; -------------------------------------------------------------------------------- ; @Title: MB86R12/MB86R11F On-Chip Peripherals ; @Props: Released ; @Author: AMM ; @Manufacturer: CYPRESS ; @Doc: hardware-manual-for-es3-es4-rev250.pdf ; rd-mb86r12-EMERALD-P-REGISTER_Rev1-40_released.pdf ; hm-mb86r12-EMERALD-P_rev1-40_released.pdf ; @Core: Cortex-A9 ; @Chip: MB86R12, MB86R11F ; @Copyright: (C) 1989-2017 Lauterbach GmbH, licensed for use with TRACE32(R) only ; -------------------------------------------------------------------------------- ; $Id: permb86r1x.per 15964 2023-04-13 11:46:29Z bschroefel $ ; Known Problems : ; APIX TX ; no addresses for Apix2_status_2 and I2C_Outbound_Job_Cancel (MB86R12 core) config 16. 8. width 0xb tree "Core Registers (Cortex-A9)" width 0x8 ; -------------------------------------------------------------------------------- ; Identification registers ; -------------------------------------------------------------------------------- tree "ID Registers" rgroup.long c15:0x0++0x0 line.long 0x0 "MIDR,Main ID Register" hexmask.long.byte 0x0 24.--31. 0x1 " IMPL ,Implementer code" bitfld.long 0x0 20.--23. " VAR ,Variant" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x0 16.--19. " ARCH , Architecture" "Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,ARMv7" textline " " hexmask.long.word 0x0 4.--15. 0x1 " PART ,Primary Part Number" bitfld.long 0x0 0.--3. " REV ,Revision Number" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" rgroup.long c15:0x100++0x0 line.long 0x0 "CTR,Cache Type Register" bitfld.long 0x0 29.--31. " FORMAT ,Format" "Not ARMv7,Not ARMv7,Not ARMv7,Not ARMv7,ARMv7,Not ARMv7,Not ARMv7,Not ARMv7" bitfld.long 0x0 24.--27. " CWG ,Cache Writeback Granule" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x0 20.--23. " ERG ,Exclusives Reservation Granule" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x0 16.--19. " DMINLINE ,D-Cache Minimum Line Size" "1 word,2 words,4 words,8 words,16 words,32 words,64 words,128 words,256 words,512 words,1024 words,2048 words,4096 words,8192 words,16384 words,32768 words" textline " " bitfld.long 0x0 14.--15. " L1POLICY ,L1 Instruction cache policy" "Reserved,ASID,Virtual,Physical" bitfld.long 0x0 0.--3. " IMINLINE ,I-Cache Minimum Line Size" "1 word,2 words,4 words,8 words,16 words,32 words,64 words,128 words,256 words,512 words,1024 words,2048 words,4096 words,8192 words,16384 words,32768 words" rgroup.long c15:0x200++0x0 line.long 0x0 "TCMTR,Tighly-Coupled Memory Type Register" rgroup.long c15:0x300++0x0 line.long 0x0 "TLBTR,TLB Type Register" hexmask.long.byte 0x0 16.--23. 0x1 " ILSIZE ,Specifies the number of instruction TLB lockable entries" hexmask.long.byte 0x0 8.--15. 0x1 " DLSIZE ,Specifies the number of unified or data TLB lockable entries" bitfld.long 0x0 1. " TLB_SIZE ,TLB Size" "64,128" textline " " bitfld.long 0x0 0. " NU ,Unified or Separate TLBs" "Unified,Separate" rgroup.long c15:0x500++0x0 line.long 0x0 "MPIDR,Multiprocessor Affinity Register" bitfld.long 0x00 30. " U ,Processor is part of a multiprocessor or uniprocessor system" "Multiprocessor,Uniprocessor" bitfld.long 0x00 8.--11. " CLUSTERID ,Value read in CLUSTERID configuration pins" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 0.--1. " CPUID ,Value depends on the number of configured CPUs" "0,1,2,3" rgroup.long c15:0x0410++0x00 line.long 0x00 "MMFR0,Memory Model Feature Register 0" bitfld.long 0x00 24.--27. " FCSE ,Fast Context Switch Memory Mappings Support" "Not supported,?..." bitfld.long 0x00 20.--23. " ACR ,Auxiliary Control Register Support" "Reserved,Supported,?..." bitfld.long 0x00 16.--19. " TCM ,TCM and Associated DMA Support" "Not supported,?..." textline " " bitfld.long 0x00 12.--15. " OSS ,Outer Shareable Support" "Not supported,?..." bitfld.long 0x00 8.--11. " CC_CPUA ,Cache Coherency Support" "Reserved,Supported,?..." bitfld.long 0x00 4.--7. " PMSA ,Physical Memory System Architecture (PMSA) Support" "Not supported,?..." textline " " bitfld.long 0x00 0.--3. " VMSA ,Virtual Memory System Architecture (VMSA) Support" "Reserved,Reserved,Reserved,Supported,?..." rgroup.long c15:0x0510++0x00 line.long 0x00 "MMFR1,Memory Model Feature Register 1" bitfld.long 0x00 28.--31. " BTB ,Branch Predictor" "Reserved,Reserved,Required,?..." bitfld.long 0x00 24.--27. " L1TCO ,Test and Clean Operations on Data Cache/Harvard/Unified Architecture Support" "Not supported,?..." bitfld.long 0x00 20.--23. " L1UCMO ,L1 Cache/All Maintenance Operations/Unified Architecture Support" "Not supported,?..." textline " " bitfld.long 0x00 16.--19. " L1HCMO ,L1 Cache/All Maintenance Operations/Harvard Architecture Support" "Not supported,?..." bitfld.long 0x00 12.--15. " L1UCLMOSW ,L1 Cache Line Maintenance Operations by Set and Way/Unified Architecture Support" "Not supported,?..." bitfld.long 0x00 8.--11. " L1HCLMOSW ,L1 Cache Line Maintenance Operations by Set and Way/Harvard Architecture Support" "Not supported,?..." textline " " bitfld.long 0x00 4.--7. " L1UCLMOMVA ,L1 Cache Line Maintenance Operations by VA/Unified Architecture Support" "Not supported,?..." bitfld.long 0x00 0.--3. " L1HCLMOMVA ,L1 Cache Line Maintenance Operations by VA/Harvard Architecture" "Not supported,?..." rgroup.long c15:0x0610++0x00 line.long 0x00 "MMFR2,Memory Model Feature Register 2" bitfld.long 0x00 28.--31. " HAF ,Hardware Access Flag Support" "Not supported,?..." bitfld.long 0x00 24.--27. " WFI ,Wait for Interrupt Stalling Support" "Reserved,Supported,?..." bitfld.long 0x00 20.--23. " MBF ,Memory Barrier Operations Support" "Reserved,Reserved,Supported,?..." textline " " bitfld.long 0x00 16.--19. " UTLBMO ,TLB Maintenance Operations/Unified Architecture Support" "Reserved,Reserved,Reserved,Supported,?..." bitfld.long 0x00 12.--15. " HTLBMO ,TLB Maintenance Operations/Harvard Architecture Support" "Not supported,?..." bitfld.long 0x00 8.--11. " HL1CMRO ,Cache Maintenance Range Operations/Harvard Architecture Support" "Not supported,?..." textline " " bitfld.long 0x00 4.--7. " HL1BPCRO ,Background Prefetch Cache Range Operations/Harvard Architecture Support" "Not supported,?..." bitfld.long 0x00 0.--3. " HL1FPCRO ,Foreground Prefetch Cache Range Operations/Harvard Architecture Support" "Not supported,?..." rgroup.long c15:0x0710++0x00 line.long 0x00 "MMFR3,Memory Model Feature Register 3" bitfld.long 0x00 28.--31. " SS ,Supersection support" "Supported,?..." bitfld.long 0x00 20.--23. " CW ,Coherent walk" "Supported,?..." bitfld.long 0x00 12.--15. " MB ,Invalidate broadcast Support" "Reserved,Reserved,Supported,?..." textline " " bitfld.long 0x00 8.--11. " BPM ,Invalidate Branch predictor Support" "Reserved,Supported,?..." bitfld.long 0x00 4.--7. " HCMOSW ,Invalidate Cache by Set and Way/Clean by Set and Way/Invalidate and Clean by Set and Way Support" "Reserved,Supported,?..." bitfld.long 0x00 0.--3. " HCMOMVA ,Invalidate Cache MVA Support" "Reserved,Supported,?..." rgroup.long c15:0x0020++0x00 line.long 0x00 "ISAR0,Instruction Set Attribute Register 0" bitfld.long 0x00 24.--27. " DIVI ,Divide Instructions Support" "Not supported,?..." bitfld.long 0x00 20.--23. " DEBI ,Debug Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 16.--19. " CI ,Coprocessor Instructions Support" "Not supported,?..." textline " " bitfld.long 0x00 12.--15. " CBI ,Combined Compare and Branch Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 8.--11. " BI ,Bitfield Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 4.--7. " BCI ,Bit Counting Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 0.--3. " SI ,Swap Instructions Support" "Reserved,Supported,?..." rgroup.long c15:0x0120++0x00 line.long 0x00 "ISAR1,Instruction Set Attribute Register 1" bitfld.long 0x00 28.--31. " JI ,Jazelle Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 24.--27. " INTI ,Instructions That Branch Between ARM and Thumb Code Support" "Reserved,Reserved,Reserved,Supported,?..." bitfld.long 0x00 20.--23. " IMMI ,Immediate Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 16.--19. " ITEI ,If Then Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 12.--15. " EXTI ,Extend Instructions Support" "Reserved,Reserved,Supported,?..." bitfld.long 0x00 8.--11. " E2I ,Exception 2 Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 4.--7. " E1I ,Exception 1 Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 0.--3. " ENDI ,Endianness Control Instructions Support" "Reserved,Supported,?..." rgroup.long c15:0x0220++0x00 line.long 0x00 "ISAR2,Instruction Set Attribute Register 2" bitfld.long 0x00 28.--31. " RI ,Reversal Instructions Support" "Reserved,Reserved,Supported,?..." bitfld.long 0x00 24.--27. " PSRI ,PSR Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 20.--23. " UMI ,Advanced Unsigned Multiply Instructions Support" "Reserved,Reserved,Supported,?..." textline " " bitfld.long 0x00 16.--19. " SMI ,Advanced Signed Multiply Instructions Support" "Reserved,Reserved,Reserved,Supported,?..." bitfld.long 0x00 12.--15. " MI ,Multiply Instructions Support" "Reserved,Reserved,Supported,?..." bitfld.long 0x00 8.--11. " II ,Multi-Access Interruptible Instructions Support" "Not supported,?..." textline " " bitfld.long 0x00 4.--7. " MHI ,Memory Hint Instructions Support" "Reserved,Reserved,Reserved,Supported,?..." bitfld.long 0x00 0.--3. " LSI ,Load and Store Instructions Support" "Reserved,Supported,?..." rgroup.long c15:0x0320++0x00 line.long 0x00 "ISAR3,Instruction Set Attribute Register 3" bitfld.long 0x00 28.--31. " T2E ,Thumb-2 Extensions Support" "Reserved,Supported,?..." bitfld.long 0x00 24.--27. " NOPI ,True NOP Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 20.--23. " TCI ,Thumb Copy Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 16.--19. " TBI ,Table Branch Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 12.--15. " SPI ,Synchronization Primitive Instructions Support" "Reserved,Reserved,Supported,?..." bitfld.long 0x00 8.--11. " SVCI ,SVC Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 4.--7. " SIMDI ,Single Instruction Multiple Data (SIMD) Instructions Support" "Reserved,Reserved,Reserved,Supported,?..." bitfld.long 0x00 0.--3. " SI ,Saturate Instructions Support" "Reserved,Supported,?..." rgroup.long c15:0x0420++0x00 line.long 0x00 "ISAR4,Instruction Set Attribute Register 4" bitfld.long 0x00 28.--31. " SWP_frac ,SWAP_frac" "Supported,?..." bitfld.long 0x00 24.--27. " PSR_M_I ,PSR_M Instructions Support" "Not supported,?..." bitfld.long 0x00 20.--23. " SPRI ,Synchronization Primitive instructions" "Not supported,?..." textline " " bitfld.long 0x00 16.--19. " BI ,Barrier Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 12.--15. " SMCI ,SMC Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 8.--11. " WBI ,Write-Back Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 4.--7. " WSI ,With-Shift Instructions Support" "Reserved,Reserved,Reserved,Reserved,Supported,?..." bitfld.long 0x00 0.--3. " UI ,Unprivileged Instructions Support" "Reserved,Reserved,Supported,?..." rgroup.long c15:0x0520++0x00 line.long 0x00 "ISAR5,Instruction Set Attribute Registers 5 (Reserved)" rgroup.long c15:0x0620++0x00 line.long 0x00 "ISAR6,Instruction Set Attribute Registers 6 (Reserved)" rgroup.long c15:0x0720++0x00 line.long 0x00 "ISAR7,Instruction Set Attribute Registers 7 (Reserved)" rgroup.long c15:0x0010++0x00 line.long 0x00 "PFR0,Processor Feature Register 0" bitfld.long 0x00 12.--15. " STATE3 ,Thumb-2 Execution Environment (Thumb-2EE) Support" "Reserved,Supported,?..." bitfld.long 0x00 8.--11. " STATE2 ,Java Extension Interface Support" "Reserved,Reserved,Supported,?..." bitfld.long 0x00 4.--7. " STATE1 ,Thumb Encoding Supported by the Processor Type" "Reserved,Reserved,Reserved,Supported,?..." textline " " bitfld.long 0x00 0.--3. " STATE0 ,ARM Instruction Set Support" "Reserved,Supported,?..." rgroup.long c15:0x0110++0x00 line.long 0x00 "PFR1,Processor Feature Register 1" bitfld.long 0x00 8.--11. " MPM ,Microcontroller Programmer's Model Support" "Not supported,?..." bitfld.long 0x00 4.--7. " SE ,Security Extensions Architecture v1 Support" "Reserved,Supported,?..." bitfld.long 0x00 0.--3. " PM ,Standard ARMv4 Programmer's Model Support" "Reserved,Supported,?..." rgroup.long c15:0x0210++0x00 line.long 0x00 "DFR0,Debug Feature Register 0" bitfld.long 0x00 20.--23. " MDM_MM ,Microcontroller Debug Model Support" "Not supported,?..." bitfld.long 0x00 16.--19. " TDM_MM ,Trace Debug Model (Memory-Mapped) Support" "Reserved,Supported,?..." bitfld.long 0x00 12.--15. " TDM_CB ,Coprocessor-Based Trace Debug Model Support" "Not supported,?..." textline " " bitfld.long 0x00 8.--11. " CDM_MM ,Memory-Mapped Debug Model Support" "Reserved,Reserved,Reserved,Reserved,Supported,?..." bitfld.long 0x00 4.--7. " SDM_CB ,Secure Debug Model (Coprocessor) Support" "Reserved,Reserved,Reserved,Reserved,Supported,?..." bitfld.long 0x00 0.--3. " CDM_CB ,Coprocessor Debug Model Support" "Reserved,Reserved,Reserved,Reserved,Supported,?..." rgroup.long c15:0x0310++0x00 line.long 0x00 "AFR0,Auxiliary Feature Register 0" hexmask.long 0x00 0.--31. 1. " AF ,Auxiliary Feature" tree.end width 0x8 tree "System Control and Configuration" group.long c15:0x1++0x0 line.long 0x0 "SCTLR,Control Register" bitfld.long 0x0 30. " TE ,Thumb exception enable" "ARM,Thumb" bitfld.long 0x0 29. " AFE ,Access Flag Enable" "Disabled,Enabled" bitfld.long 0x0 28. " TRE ,TEX remap enable" "Disabled,Enabled" textline " " bitfld.long 0x0 27. " NMFI ,DNonmaskable Fast Interrupt enable" "Disabled,Enabled" bitfld.long 0x0 25. " EE ,Exception endianess" "Little,Big" bitfld.long 0x0 14. " RR ,Replacement strategy for caches, BTAC, and micro TLBs" "Random,Round robin" textline " " bitfld.long 0x0 13. " V ,Base Location of Exception Registers" "0x00000000,0xFFFF0000" bitfld.long 0x0 12. " I ,Instruction Cache Enable" "Disabled,Enabled" bitfld.long 0x0 11. " Z ,Branch Prediction Enable" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " SW ,SWP/SWPB Enable" "Disabled,Enabled" bitfld.long 0x0 2. " C ,Enable unified cache or data cache" "Disabled,Enabled" bitfld.long 0x0 1. " A ,Strict Alignment" "Disabled,Enabled" textline " " bitfld.long 0x0 0. " M ,MMU or Protection Unit" "Disabled,Enabled" group.long c15:0x101++0x0 line.long 0x0 "ACTLR,Auxiliary Control Register" bitfld.long 0x00 9. " PARON ,Parity On" "Disabled,Enabled" bitfld.long 0x00 7. " EXCL ,Exclusive cache Enable" "Disabled,Enabled" bitfld.long 0x00 6. " SMP ,Signals if the Cortex-A9 processor is taking part in coherency or not" "0,1" textline " " bitfld.long 0x00 3. " FOZ ,Full Of Zero mode Enable" "Disabled,Enabled" bitfld.long 0x00 2. " DP1 ,L1 Dside prefetch Enable" "Disabled,Enabled" bitfld.long 0x00 1. " DP2 ,L2 Dside prefetch Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " FW ,Cache and TLB maintenance broadcast" "Disabled,Enabled" group.long c15:0x201++0x0 line.long 0x0 "CPACR,Coprocessor Access Control Register" bitfld.long 0x0 31. " ASEDIS ,Disable Advanced SIMD Extension functionality" "No,Yes" bitfld.long 0x0 30. " D32DIS ,Disable use of D16-D31 of the VFP register file" "No,Yes" bitfld.long 0x0 22.--23. " CP11 ,Coprocesor access control" "Denied,Privileged,Reserved,Full" textline " " bitfld.long 0x0 20.--21. " CP10 ,Coprocesor access control" "Denied,Privileged,Reserved,Full" textline " " group.long c15:0x11++0x0 line.long 0x0 "SCR,Secure Configuration Register" bitfld.long 0x00 6. " NET ,Not early termination" "Not early,Early" bitfld.long 0x00 5. " AW ,Controls whether the Non-secure world can modify the A-bit in the CPSR" "Not allowed,Allowed" bitfld.long 0x00 4. " FW ,FW-bit controls whether the Non-secure world can modify the F-bit in the CPSR" "Not allowed,Allowed" textline " " bitfld.long 0x00 3. " EA ,External Abort exceptions handled in Abort mode or Monitor mode" "Abort,Monitor" bitfld.long 0x00 2. " FIQ ,FIQ exceptions handled in Abort mode or Monitor mode" "FIQ,Monitor" bitfld.long 0x00 1. " IRQ ,IRQ exceptions handled in Abort mode or Monitor mode" "IRQ,Monitor" textline " " bitfld.long 0x00 0. " NS ,Secure mode " "Secure,Non-secure" group.long c15:0x111++0x0 line.long 0x0 "SDER,Secure Debug Enable Register" bitfld.long 0x00 1. " SUNIDEN ,Non-Invasive Secure User Debug Enable bit" "Denied,Permitted" bitfld.long 0x00 0. " SUIDEN ,Invasive Secure User Debug Enable bit" "Denied,Permitted" group.long c15:0x0211++0x00 line.long 0x00 "NSACR,Non-Secure Access Control Register" bitfld.long 0x00 18. " NS_SMP ,Determines if the SMP bit of the Auxiliary Control Register is writable in Non-secure state" "Disabled,Enabled" bitfld.long 0x00 17. " TL ,Lockable Page Table Entries Allocation in Nonsecure World" "Denied,Permitted" bitfld.long 0x00 15. " NSASEDIS ,Disable Non-secure Advanced SIMD Extension functionality" "Denied,Permitted" textline " " bitfld.long 0x00 14. " NSD32DIS ,Disable the Non-secure use of D16-D31 of the VFP register" "Denied,Permitted" bitfld.long 0x00 11. " CP11 ,Coprocessor 11 in the Nonsecure World Access Permission" "Denied,Permitted" bitfld.long 0x00 10. " CP10 ,Coprocessor 10 in the Nonsecure World Access Permission" "Denied,Permitted" group.long c15:0x0311++0x00 line.long 0x00 "VCR,Virtualization Control Register" bitfld.long 0x00 8. " AMO ,Abort Mask Override" "0,1" bitfld.long 0x00 7. " IMO ,IRQ Mask Override" "0,1" bitfld.long 0x00 6. " IFO ,FIQ Mask Override" "0,1" textline " " group.long c15:0x000c++0x00 line.long 0x00 "VBAR,Secure or Nonsecure Vector Base Address Register" hexmask.long 0x00 5.--31. 0x20 " VBA ,Base Address" group.long c15:0x10c++0x00 line.long 0x0 "MVBAR,Monitor Vector Base Address Register" hexmask.long 0x00 5.--31. 0x20 " MVBA , Monitor Vector Base Address" rgroup.long c15:0x1C++0x0 line.long 0x0 "ISR,Interrupt status Register" bitfld.long 0x0 8. " A ,Pending External Abort" "Not pending,Pending" bitfld.long 0x0 7. " I ,Pending IRQ" "Not pending,Pending" bitfld.long 0x0 6. " F ,Pending FIQ" "Not pending,Pending" group.long c15:0x11c++0x0 line.long 0x00 "VIR,Virtualization Interrupt Register" bitfld.long 0x00 8. " VA ,Virtual Abort" "0,1" bitfld.long 0x00 7. " VI ,Virtual IRQ" "0,1" bitfld.long 0x00 6. " VF ,Virtual FIQ" "0,1" textline " " group.long c15:0xf++0x0 line.long 0x00 "PCR,Power Control Register" bitfld.long 0x00 8.--10. " MCL ,Max Clock Latency" "0,1,2,3,4,5,6,7" bitfld.long 0x00 0. " EDCG ,Enable Dynamic Clock Gating" "Disabled,Enabled" group.long c15:0x1f++0x0 line.long 0x00 "NEONBR,NEON Busy Register" bitfld.long 0x00 0. " BUSY ,NEON Busy" "No,Yes" group.long c15:0x400f++0x0 line.long 0x00 "CBAR,Configuration Base Address Register" hexmask.long 0x00 0.--31. 1. " CBAR ,Configuration Base Address Register" tree.end width 0x08 tree "Memory Management Unit" group.long c15:0x1++0x0 line.long 0x0 "SCTLR,Control Register" bitfld.long 0x0 30. " TE ,Thumb exception enable" "ARM,Thumb" bitfld.long 0x0 29. " AFE ,Access Flag Enable" "Disabled,Enabled" bitfld.long 0x0 28. " TRE ,TEX remap enable" "Disabled,Enabled" textline " " bitfld.long 0x0 27. " NMFI ,DNonmaskable Fast Interrupt enable" "Disabled,Enabled" bitfld.long 0x0 25. " EE ,Exception endianess" "Little,Big" bitfld.long 0x0 14. " RR ,Replacement strategy for caches, BTAC, and micro TLBs" "Random,Round robin" textline " " bitfld.long 0x0 13. " V ,Base Location of Exception Registers" "0x00000000,0xFFFF0000" bitfld.long 0x0 12. " I ,Instruction Cache Enable" "Disabled,Enabled" bitfld.long 0x0 11. " Z ,Branch Prediction Enable" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " SW ,SWP/SWPB Enable" "Disabled,Enabled" bitfld.long 0x0 2. " C ,Enable unified cache or data cache" "Disabled,Enabled" bitfld.long 0x0 1. " A ,Strict Alignment" "Disabled,Enabled" textline " " bitfld.long 0x0 0. " M ,MMU or Protection Unit" "Disabled,Enabled" textline " " group.long c15:0x0002++0x00 line.long 0x00 "TTBR0,Translation Table Base Register 0" hexmask.long 0x00 14.--31. 0x4000 " TTB0 ,Translation Table Base Address" bitfld.long 0x00 6. 0. " IRGN[1:0] ,Indicates inner cacheability" "Noncacheable,Back/allocated,Through,Back/not allocated" textline " " bitfld.long 0x00 3.--4. " RGN ,Outer Cacheable Attributes for Page Table Walking" "Noncacheable,Back/allocated,Through,Back/not allocated" bitfld.long 0x00 1. " S ,Page Table Walk to Shared Memory" "Nonshared,Shared" group.long c15:0x0102++0x00 line.long 0x00 "TTBR1,Translation Table Base Register 1" hexmask.long 0x00 14.--31. 0x4000 " TTB1 ,Translation Table Base Address" bitfld.long 0x00 6. 0. " IRGN[1:0] ,Indicates inner cacheability" "Noncacheable,Back/allocated,Through,Back/not allocated" textline " " bitfld.long 0x00 3.--4. " RGN ,Outer Cacheable Attributes for Page Table Walking" "Noncacheable,Back/allocated,Through,Back/not allocated" bitfld.long 0x00 1. " S ,Page Table Walk to Shared Memory" "Nonshared,Shared" group.long c15:0x0202++0x00 line.long 0x00 "TTBCR,Translation Table Base Control Register" bitfld.long 0x00 5. " PD1 ,Page Table Walk on a TLB Miss When Using Translation Table Base Register 1" "Enable,Disable" bitfld.long 0x00 4. " PD0 ,Page Table Walk on a TLB Miss When Using Translation Table Base Register 0" "Enable,Disable" bitfld.long 0x0 0.--2. " N ,Translation Table Base Register 0 page table boundary size" "Off,0x80000000,0x40000000,0x20000000,0x10000000,0x08000000,0x04000000,0x02000000" textline " " group.long c15:0x3--0x3 line.long 0x0 "DACR,Domain Access Control Register" bitfld.long 0x0 30.--31. " D15 ,Domain Access 15" "Denied,Client,Reserved,Manager" bitfld.long 0x0 28.--29. " D14 ,Domain Access 14" "Denied,Client,Reserved,Manager" bitfld.long 0x0 26.--27. " D13 ,Domain Access 13" "Denied,Client,Reserved,Manager" bitfld.long 0x0 24.--25. " D12 ,Domain Access 12" "Denied,Client,Reserved,Manager" textline " " bitfld.long 0x0 22.--23. " D11 ,Domain Access 11" "Denied,Client,Reserved,Manager" bitfld.long 0x0 20.--21. " D10 ,Domain Access 10" "Denied,Client,Reserved,Manager" bitfld.long 0x0 18.--19. " D9 ,Domain Access 9" "Denied,Client,Reserved,Manager" bitfld.long 0x0 16.--17. " D8 ,Domain Access 8" "Denied,Client,Reserved,Manager" textline " " bitfld.long 0x0 14.--15. " D7 ,Domain Access 7" "Denied,Client,Reserved,Manager" bitfld.long 0x0 12.--13. " D6 ,Domain Access 6" "Denied,Client,Reserved,Manager" bitfld.long 0x0 10.--11. " D5 ,Domain Access 5" "Denied,Client,Reserved,Manager" bitfld.long 0x0 8.--9. " D4 ,Domain Access 4" "Denied,Client,Reserved,Manager" textline " " bitfld.long 0x0 6.--7. " D3 ,Domain Access 3" "Denied,Client,Reserved,Manager" bitfld.long 0x0 4.--5. " D2 ,Domain Access 2" "Denied,Client,Reserved,Manager" bitfld.long 0x0 2.--3. " D1 ,Domain Access 1" "Denied,Client,Reserved,Manager" bitfld.long 0x0 0.--1. " D0 ,Domain Access 0" "Denied,Client,Reserved,Manager" textline " " group.long c15:0x0005++0x00 line.long 0x00 "DFSR,Data Fault Status Register" bitfld.long 0x00 12. " EXT ,External Abort Qualifier" "DECERR,SLVERR" bitfld.long 0x00 11. " RW ,Access Caused an Abort Type" "Read,Write" textline " " bitfld.long 0x00 4.--7. " DOMAIN ,Domain Accessed When a Data Fault Occurs" "D0,D1,D2,D3,D4,D5,D6,D7,D8,D9,D10,D11,D12,D13,D14,D15" bitfld.long 0x00 0.--3. 10. " STATUS ,Generated Exception Type" "Reserved,Alignment,Debug,Access/section,Instruction,Translation/section,Access/page,Translation/page,Nontranslation/synchronous external,Domain/section,Reserved,Domain/page,L1/external,Permission/section,L2/external,Permission/page,Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,Asynchronous external,?..." group.long c15:0x0006++0x00 line.long 0x00 "DFAR,Data Fault Address Register" hexmask.long 0x00 0.--31. 1. " DFA ,Data Fault Address" group.long c15:0x0105++0x00 line.long 0x00 "IFSR,Instruction Fault Status Register" bitfld.long 0x00 12. " SD ,External Abort Qualifier" "DECERR,SLVERR" bitfld.long 0x00 0.--3. 10. " STATUS ,Generated Exception Type" "Reserved,Alignment,Debug,Access/section,Instruction,Translation/section,Access/page,Translation/page,Nontranslation/synchronous external,Domain/section,Reserved,Domain/page,L1/external,Permission/section,L2/external,Permission/page,Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,Asynchronous external,?..." group.long c15:0x0206++0x00 line.long 0x00 "IFAR,Instruction Fault Address Register" hexmask.long 0x00 0.--31. 1. " IFA ,Instruction Fault Address" group.long c15:0x0015++0x00 line.long 0x00 "DAFSR,Data Auxiliary Fault Status Register" hexmask.long 0x00 0.--31. 1. " DAFS ,Data Auxiliary Fault Status" group.long c15:0x0115++0x00 line.long 0x00 "IAFSR,Instruction Auxiliary Fault Status Register" hexmask.long 0x00 0.--31. 1. " IAFS ,Instruction Auxiliary Fault Status" textline " " group.long c15:0xa++0x0 line.long 0x0 "TLBLR,TLB Lockdown Register" bitfld.long 0x0 28.--29. " VICTIM ,Victim Value Increments after Each Tabel Walk" "0,1,2,3" bitfld.long 0x0 0. " P ,Lockdown by Victim or Set Associative Region of TLB" "Associative,Lockdown" group.long c15:0x525f++0x0 line.long 0x00 "MTLBVAR,Main TLB VA Register" hexmask.long 0x00 12.--31. 1. " VPN ,Virtual Page Number" bitfld.long 0x00 10. " NS ,Non-Secure bit" "Not secured,Secured" textline " " hexmask.long.word 0x00 0.--9. 1. " PROCESS ,Memory space identifier" group.long c15:0x526f++0x0 line.long 0x00 "MTLBPAR,Main TLB PA Register" hexmask.long 0x00 12.--31. 1. " PPN ,Physical Page Number" bitfld.long 0x00 6.--7. " SZ ,Region Size" "16MB,4KB,64KB,1MB" textline " " bitfld.long 0x00 1.--3. " AP ,Access permission" "All access,Supervisor access only,Supervisor R/W access,Full,Reserved,Supervisor read only,Supervisor/Usr read only,Supervisor/Usr read only" bitfld.long 0x00 0. "V ,Value bit" "0,1" group.long c15:0x527f++0x0 line.long 0x00 "MTLBAR,Main TLB Attribute Register" bitfld.long 0x00 11. " NS ,Non-secure description" "Not secured,Secured" bitfld.long 0x00 7.--10. " DOMAIN ,Domain number of the TLB entry" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 6. " XN ,Execute Never attribute" "0,1" bitfld.long 0x00 3.--5. " TEX ,Region type Encoding" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 1.--2. " CB ,Region type Encoding" "0,1,2,3" bitfld.long 0x00 0. " S ,Shared attribute" "0,1" group.long c15:0x0047++0x00 line.long 0x00 "PAR,PA Register" hexmask.long 0x00 12.--31. 0x1000 " PA ,Physical Adress" bitfld.long 0x00 9. " NS ,Non-secure" "Not secured,Secured" textline " " bitfld.long 0x00 7. " SH ,Shareable attribute" "Non-shareable,Shareable" bitfld.long 0x00 4.--6. " Inner ,Signals region inner attributes" "Noncacheable,Strongly-ordered,Reserved,Device,Reserved,Write-back allocate,Write-through,Write-back" textline " " bitfld.long 0x00 2.--3. " Outer ,Signals region outer attributes for normal memory type" "Noncacheable,Write-back allocate,Write-through,Write-back" bitfld.long 0x00 1. " SS ,Supersection Enable bit" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " F ,Translation Successful" "Successful,No successful" textline " " group.long c15:0x002A++0x0 line.long 0x00 "PRRR,Primary Region Remap Register" bitfld.long 0x00 19. " NS1 ,Shareable Attribute Remap when S=1 for Normal Regions" "Remapped,Not remapped" bitfld.long 0x00 18. " NS0 ,Shareable Attribute Remap when S=0 for Normal Regions" "Not remapped,Remapped" textline " " bitfld.long 0x00 17. " DS1 ,Shareable Attribute Remap when S=1 for Device regions" "Remapped,Not remapped" bitfld.long 0x00 16. " DS0 ,Shareable Attribute Remap when S=0 for Device regions" "Not remapped,Remapped" textline " " bitfld.long 0x00 14.--15. " TR7 ,{TEX[0] C B} = b111 Remap" "Strongly ordered,Device,Normal,UNP" bitfld.long 0x00 12.--13. " TR6 ,{TEX[0] C B} = b110 Remap" "Strongly ordered,Device,Normal,UNP" textline " " bitfld.long 0x00 10.--11. " TR5 ,{TEX[0] C B} = b101 Remap" "Strongly ordered,Device,Normal,UNP" bitfld.long 0x00 8.--9. " TR4 ,{TEX[0] C B} = b100 Remap" "Strongly ordered,Device,Normal,UNP" textline " " bitfld.long 0x00 6.--7. " TR3 ,{TEX[0] C B} = b011 Remap" "Strongly ordered,Device,Normal,UNP" bitfld.long 0x00 4.--5. " TR2 ,{TEX[0] C B} = b010 Remap" "Strongly ordered,Device,Normal,UNP" textline " " bitfld.long 0x00 2.--3. " TR1 ,{TEX[0] C B} = b001 Remap" "Strongly ordered,Device,Normal,UNP" bitfld.long 0x00 0.--1. " TR0 ,{TEX[0] C B} = b000 Remap" "Strongly ordered,Device,Normal,UNP" group.long c15:0x012A++0x0 line.long 0x00 "NMRR,Normal Memory Remap Register" bitfld.long 0x00 30.--31. " OR7 ,Outer Attribute for {TEX[0] C B} = b111 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" bitfld.long 0x00 28.--29. " OR6 ,Outer Attribute for {TEX[0] C B} = b110 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" textline " " bitfld.long 0x00 26.--27. " OR5 ,Outer Attribute for {TEX[0] C B} = b101 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" bitfld.long 0x00 24.--25. " OR4 ,Outer Attribute for {TEX[0] C B} = b100 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" textline " " bitfld.long 0x00 22.--23. " OR3 ,Outer Attribute for {TEX[0] C B} = b011 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" bitfld.long 0x00 20.--21. " OR2 ,Outer Attribute for {TEX[0] C B} = b010 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" textline " " bitfld.long 0x00 18.--19. " OR1 ,Outer Attribute for {TEX[0] C B} = b001 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" bitfld.long 0x00 16.--17. " OR0 ,Outer Attribute for {TEX[0] C B} = b000 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" textline " " bitfld.long 0x00 14.--15. " IR7 ,Inner attribute for {TEX[0] C B} = b111 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" bitfld.long 0x00 12.--13. " IR6 ,Inner attribute for {TEX[0] C B} = b110 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" textline " " bitfld.long 0x00 10.--11. " IR5 ,Inner attribute for {TEX[0] C B} = b101 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" bitfld.long 0x00 8.--9. " IR4 ,Inner attribute for {TEX[0] C B} = b100 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" textline " " bitfld.long 0x00 6.--7. " IR3 ,Inner attribute for {TEX[0] C B} = b011 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" bitfld.long 0x00 4.--5. " IR2 ,Inner attribute for {TEX[0] C B} = b010 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" textline " " bitfld.long 0x00 2.--3. " IR1 ,Inner attribute for {TEX[0] C B} = b001 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" bitfld.long 0x00 0.--1. " IR0 ,Inner attribute for {TEX[0] C B} = b000 Remap" "Noncachable,Write-back allocate,Write-through,Write-back no allocate" textline " " rgroup.long c15:0x000d++0x00 line.long 0x00 "FCSEIDR,FCSE PID Register" hexmask.long 0x00 0.--31. 1. " FCSEPID ,Process for Fast Context Switch Identification and Specification" group.long c15:0x10d++0x0 line.long 0x0 "CONTEXT,Context ID Register" hexmask.long.tbyte 0x0 8.--31. 1. " PROCID ,Process ID" hexmask.long.byte 0x0 0.--7. 1. " ASID ,Application Space ID" group.long c15:0x020d++0x00 line.long 0x00 "URWTPID,User Read/Write Thread and Process ID Register" hexmask.long 0x00 0.--31. 1. " URWTPID ,User Read/Write Thread and Process ID" group.long c15:0x030d++0x00 line.long 0x00 "UROTPID,User Read-Only Thread and Process ID Register" hexmask.long 0x00 0.--31. 1. " UROTPID ,User Read-Only Thread and Process ID" group.long c15:0x040d++0x00 line.long 0x00 "POTPID,Privileged Only Thread and Process ID Register" hexmask.long 0x00 0.--31. 1. " POTPID ,Privileged Only Thread and Process ID" tree.end width 0xC tree "Cache Control and Configuration" rgroup.long c15:0x1100++0x0 line.long 0x0 "CLIDR,Cache Level ID Register" bitfld.long 0x00 27.--29. " LOU ,Level of Unification" "Level 1,Level 2,Level 3,Level 4,Level 5,Level 6,Level 7,Level 8" bitfld.long 0x00 24.--26. " LOC ,Level of Coherency" "Level 1,Level 2,Level 3,Level 4,Level 5,Level 6,Level 7,Level 8" textline " " bitfld.long 0x00 21.--23. " CTYPE8 ,Cache type for levels 8" "No cache,I-cache,D-cache,Separate I/D,Unified,?..." bitfld.long 0x00 18.--20. " CTYPE7 ,Cache type for levels 7" "No cache,I-cache,D-cache,Separate I/D,Unified,?..." textline " " bitfld.long 0x00 15.--17. " CTYPE6 ,Cache type for levels 6" "No cache,I-cache,D-cache,Separate I/D,Unified,?..." bitfld.long 0x00 12.--14. " CTYPE5 ,Cache type for levels 5" "No cache,I-cache,D-cache,Separate I/D,Unified,?..." textline " " bitfld.long 0x00 9.--11. " CTYPE4 ,Cache type for levels 4" "No cache,I-cache,D-cache,Separate I/D,Unified,?..." bitfld.long 0x00 6.--8. " CTYPE3 ,Cache type for levels 3" "No cache,I-cache,D-cache,Separate I/D,Unified,?..." textline " " bitfld.long 0x00 3.--5. " CTYPE2 ,Cache type for levels 2" "No cache,I-cache,D-cache,Separate I/D,Unified,?..." bitfld.long 0x00 0.--2. " CTYPE1 ,Cache type for levels 1" "No cache,I-cache,D-cache,Separate I/D,Unified,?..." rgroup.long c15:0x1700++0x0 line.long 0x0 "AIDR,Auxiliary ID Register" hexmask.long 0x00 0.--31. 1. " AID ,Auxiliary ID" rgroup.long c15:0x1000++0x0 line.long 0x0 "CCSIDR,Current Cache Size ID Register" bitfld.long 0x00 31. " WT ,Write-Through" "Not Supported,Supported" bitfld.long 0x00 30. " WB ,Write-Back" "Not Supported,Supported" textline " " bitfld.long 0x00 29. " RA ,Read-Allocate" "Not Supported,Supported" bitfld.long 0x00 28. " WA ,Write-Allocate" "Not Supported,Supported" textline " " hexmask.long.word 0x00 13.--27. 1. " SETS ,Number of Sets" hexmask.long.word 0x00 3.--12. 1. " ASSOC ,Associativity" textline " " bitfld.long 0x00 0.--2. " LSIZE ,Line Size" "4 words,8 words,16 words,32 words,64 words,128 words,256 words,512 words" group.long c15:0x2000++0x0 line.long 0x0 "CSSELR,Cache Size Selection Register" bitfld.long 0x00 1.--3. " LEVEL ,Level" "Level 1,Level 2,Level 3,Level 4,Level 5,Level 6,Level 7,Level 8" bitfld.long 0x00 0. " IND ,Instruction/Not Data" "Data,Instruction" tree.end width 0x8 tree "L2 Preload Engine" rgroup c15:0x000b++0x00 line.long 0x00 "PLEIDR,PLE Identification Register 0" bitfld.long 0x00 0. " CH0P ,Channel 0 Present" "Not present,Present" rgroup c15:0x020b++0x00 line.long 0x00 "PLESR,PLE Status Register" bitfld.long 0x00 0. " CH0R ,Channel 0 Run" "Not running,Running" rgroup c15:0x040b++0x00 line.long 0x00 "PLEFSR,PLE FIFO Status Register" group c15:0x001b++0x00 line.long 0x00 "PLEUAR,PLE User Accessibility Register" bitfld.long 0x00 0. " U0 ,User Mode Process Access Registers for Channel 0 Permission" "Not permitted,Permitted" group c15:0x011b++0x00 line.long 0x00 "PLEPCR,PLE Parameters Control Register" tree.end width 12. tree "System Performance Monitor" group.long c15:0xC9++0x0 line.long 0x0 "PMCR,Performance Monitor Control Register" hexmask.long.byte 0x00 24.--31. 1. " IMP ,Implementer code" hexmask.long.byte 0x00 16.--23. 1. " IDCODE ,Identification code" bitfld.long 0x00 11.--15. " N ,Number of counters implemented" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 5. " DP ,Disable CCNT when prohibited" "Enabled,Disabled" textline " " bitfld.long 0x00 4. " X ,Export Enabled" "Disabled,Enabled" bitfld.long 0x00 3. " D ,Clock Divider" "Every cycle,64th cycle" bitfld.long 0x00 2. " C ,Clock Counter Reset" "No action,Reset" bitfld.long 0x00 1. " P ,Performance Counter Reset" "No action,Reset" textline " " bitfld.long 0x00 0. " E ,Counters Enable" "Disabled,Enabled" group.long c15:0x1C9++0x0 line.long 0x0 "PMCNTENSET,Count Enable Set Register" bitfld.long 0x00 31. " C ,CCNT Enabled" "Disabled,Enabled" bitfld.long 0x00 5. " P5 ,PMN5 Enabled" "Disabled,Enabled" bitfld.long 0x00 4. " P4 ,PMN5 Enabled" "Disabled,Enabled" bitfld.long 0x00 3. " P3 ,PMN3 Enabled" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " P2 ,PMN2 Enabled" "Disabled,Enabled" bitfld.long 0x00 1. " P1 ,PMN1 Enabled" "Disabled,Enabled" bitfld.long 0x00 0. " P0 ,PMN0 Enabled" "Disabled,Enabled" group.long c15:0x2C9++0x0 line.long 0x0 "PMCNTENCLR,Count Enable Clear Register" bitfld.long 0x00 31. " C ,CCNT Enabled" "Disabled,Enabled" bitfld.long 0x00 5. " P5 ,PMN5 Enabled" "Disabled,Enabled" bitfld.long 0x00 4. " P4 ,PMN5 Enabled" "Disabled,Enabled" bitfld.long 0x00 3. " P3 ,PMN3 Enabled" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " P2 ,PMN2 Enabled" "Disabled,Enabled" bitfld.long 0x00 1. " P1 ,PMN1 Enabled" "Disabled,Enabled" bitfld.long 0x00 0. " P0 ,PMN0 Enabled" "Disabled,Enabled" group.long c15:0x3C9++0x0 line.long 0x0 "PMOVSR,Overflow Flag Status Register" eventfld.long 0x00 31. " C ,CCNT overflowed" "No overflow,Overflow" eventfld.long 0x00 5. " P5 ,PMN5 overflow" "No overflow,Overflow" eventfld.long 0x00 4. " P4 ,PMN5 overflow" "No overflow,Overflow" eventfld.long 0x00 3. " P3 ,PMN3 overflow" "No overflow,Overflow" textline " " eventfld.long 0x00 2. " P2 ,PMN2 overflow" "No overflow,Overflow" eventfld.long 0x00 1. " P1 ,PMN1 overflow" "No overflow,Overflow" eventfld.long 0x00 0. " P0 ,PMN0 overflow" "No overflow,Overflow" wgroup.long c15:0x4C9++0x0 line.long 0x0 "PMSWINC,Software Increment Register" eventfld.long 0x00 5. " P5 ,Increment PMN2" "No action,Increment" eventfld.long 0x00 4. " P4 ,Increment PMN1" "No action,Increment" eventfld.long 0x00 3. " P3 ,Increment PMN3" "No action,Increment" eventfld.long 0x00 2. " P2 ,Increment PMN2" "No action,Increment" textline " " eventfld.long 0x00 1. " P1 ,Increment PMN1" "No action,Increment" eventfld.long 0x00 0. " P0 ,Increment PMN0" "No action,Increment" group.long c15:0x5C9++0x0 line.long 0x0 "PMSELR,Performance Counter Selection Register" bitfld.long 0x00 0.--5. " SEL ,Selection value" "CNT0,CNT1,CNT2,CNT3,CNT4,CNT5,?..." group.long c15:0xD9++0x0 line.long 0x00 "PMCCNTR,Cycle Count Register" group.long c15:0x01d9++0x00 line.long 0x00 "PMXEVTYPER,Event Selection Register" hexmask.long.byte 0x00 0.--7. 1. " SEL ,Event Selection" group.long c15:0x02d9++0x00 line.long 0x00 "PMCNT,Performance Monitor Count Register" group.long c15:0xE9++0x0 line.long 0x0 "PMUSERENR,User Enable Register" bitfld.long 0x00 0. " EN ,User Mode Enable" "Disabled,Enabled" group.long c15:0x1E9++0x0 line.long 0x0 "PMINTENSET,Interrupt Enable Set Register" bitfld.long 0x00 31. " C ,CCNT Overflow Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 5. " P5 ,PMCNT5 Overflow Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 4. " P4 ,PMCNT4 Overflow Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 3. " P3 ,PMCNT3 Overflow Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " P2 ,PMCNT2 Overflow Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 1. " P1 ,PMCNT1 Overflow Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 0. " P0 ,PMCNT0 Overflow Interrupt Enable" "Disabled,Enabled" group.long c15:0x2E9++0x0 line.long 0x0 "PMINTENCLR,Interrupt Enable Clear Register" eventfld.long 0x00 31. " C ,CCNT Overflow Interrupt Enable" "Disabled,Enabled" eventfld.long 0x00 5. " P5 ,PMCNT5 Overflow Interrupt Enable" "Disabled,Enabled" eventfld.long 0x00 4. " P4 ,PMCNT4 Overflow Interrupt Enable" "Disabled,Enabled" eventfld.long 0x00 3. " P3 ,PMCNT3 Overflow Interrupt Enable" "Disabled,Enabled" textline " " eventfld.long 0x00 2. " P2 ,PMCNT2 Overflow Interrupt Enable" "Disabled,Enabled" eventfld.long 0x00 1. " P1 ,PMCNT1 Overflow Interrupt Enable" "Disabled,Enabled" eventfld.long 0x00 0. " P0 ,PMCNT0 Overflow Interrupt Enable" "Disabled,Enabled" tree.end width 0xb width 10. tree "Debug Registers" rgroup c14:0x000--0x000 line.long 0x0 "DBGDIDR,Debug ID Register" bitfld.long 0x0 28.--31. " WRP ,Number of Watchpoint Register Pairs" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16" bitfld.long 0x0 24.--27. " BRP ,Number of Breakpoint Register Pairs" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16" bitfld.long 0x0 20.--23. " CONTEXT ,Number of BRPs with Context ID Comparison Capability" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16" textline " " bitfld.long 0x0 16.--19. " VERSION ,Debug Architecture Version" "Reserved,ARMv6,ARMv6.1,ARMv7,?..." textline " " bitfld.long 0x0 13. " PCSAMPLE ,PC Sample register implemented" "Not implemented,Implemented" bitfld.long 0x0 12. " SECURITY ,Security Extensions implemented" "Not implemented,Implemented" textline " " bitfld.long 0x0 4.--7. " VARIANT ,Implementation-defined Variant Number" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x0 0.--3. " REVISION ,Implementation-defined Revision Number" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " group c14:0x22--0x22 line.long 0x0 "DBGDSCR,Debug Status and Control Register" bitfld.long 0x0 30. " DTRRXFULL ,The DTRRX Full Flag" "Empty,Full" bitfld.long 0x0 29. " DTRTXfull ,The DTRTX Full Flag" "Empty,Full" textline " " bitfld.long 0x00 27. " DTRRXFULL_L ,The DTRRX Full Flag 1" "Empty,Full" bitfld.long 0x00 26. " DTRTXfull_l ,The DTRTX Full Flag 1" "Empty,Full" textline " " bitfld.long 0x0 25. " SPA ,Sticky Pipeline Advance" "No effect,Instruction retired" bitfld.long 0x0 24. " IC ,Instruction Complete" "Executing,Not executing" textline " " bitfld.long 0x0 20.--21. " DTR ,DTR Access Mode" "Non-blocking,Stall,Fast,?..." bitfld.long 0x0 19. " NSWS ,Imprecise Data Aborts discarded" "Not discarded,Discarded" textline " " bitfld.long 0x0 18. " NS ,Non-secure World Status" "Secured,Not secured" bitfld.long 0x0 17. " nSPNIDEN ,Secure Non-invasive Debug Disabled" "Enabled,Disabled" textline " " bitfld.long 0x0 16. " NSPIDEN ,Secure Invasive Debug Disabled" "Enabled,Disabled" bitfld.long 0x0 15. " MONITOR ,Monitor Debug-mode enable" "Disabled,Enabled" textline " " bitfld.long 0x0 14. " HDEN ,Halting Debug-mode enable" "Disabled,Enabled" bitfld.long 0x0 13. " EXECUTE ,Execute instruction enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " COMMS ,User mode access to Comms Channel disable" "Enabled,Disabled" bitfld.long 0x0 11. " IntDis ,Disable Interrupts" "Enabled,Disabled" textline " " bitfld.long 0x0 10. " DBGACK ,Force Debug Acknowledge" "Not forced,Forced" bitfld.long 0x0 8. " UEXT ,Sticky Undefined Exception" "No exception,Exception" textline " " bitfld.long 0x0 7. " IABORT ,Sticky Imprecise Abort" "Not aborted,Aborted" bitfld.long 0x0 6. " PABORT ,Sticky Precise Abort" "Not aborted,Aborted" textline " " bitfld.long 0x0 2.--5. " MOE ,Method of Debug Entry" "Debug Entry,Breakpoint,Imprecise Watchpoint,BKPT instruction,External debug,Vector catch,Reserved,Reserved,OS Unlock,?..." bitfld.long 0x0 1. " RESTARTED ,Core Restarted" "Debug not exited,Debug exited" textline " " bitfld.long 0x0 0. " HALTED ,Core Halted" "Normal state,Debug state" textline " " if (((per.long(c14:0x00))&0x01000)==0x00000) group c14:0x007--0x007 line.long 0x0 "DBGVCR,Vector Catch Register" bitfld.long 0x0 7. " FIQ ,Vector Catch Enable FIQ" "Disabled,Enabled" bitfld.long 0x0 6. " IRQ ,Vector Catch Enable IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 4. " DABORT ,Vector Catch Enable Data Abort" "Disabled,Enabled" bitfld.long 0x0 3. " PABORT ,Vector Catch Enable Prefetch Abort" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " SWI ,Vector Catch Enable SWI" "Disabled,Enabled" bitfld.long 0x0 1. " UNDEF ,Vector Catch Enable Undefined Instruction" "Disabled,Enabled" textline " " bitfld.long 0x0 0. " RESET ,Vector Catch Enable Reset" "Disabled,Enabled" else group c14:0x007--0x007 line.long 0x0 "DBGVCR,Vector Catch Register" bitfld.long 0x0 31. " FIQN ,Vector Catch Enable FIQ (Non-secure)" "Disabled,Enabled" bitfld.long 0x0 30. " IRQN ,Vector Catch Enable IRQ (Non-secure)" "Disabled,Enabled" textline " " bitfld.long 0x0 28. " DABORTN ,Vector Catch Enable Data Abort (Non-secure)" "Disabled,Enabled" bitfld.long 0x0 27. " PABORTN ,Vector Catch Enable Prefetch abort (Non-secure)" "Disabled,Enabled" textline " " bitfld.long 0x0 26. " SWIN ,Vector Catch Enable SWI (Non-secure)" "Disabled,Enabled" bitfld.long 0x0 25. " UNDEFS ,Vector Catch Enable Undefined (Non-secure)" "Disabled,Enabled" textline " " bitfld.long 0x0 15. " FIQS ,Vector Catch Enable FIQ (Secure)" "Disabled,Enabled" bitfld.long 0x0 14. " IRQS ,Vector Catch Enable IRQ (Secure)" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " DABORTS ,Vector Catch Enable Data Abort (Secure)" "Disabled,Enabled" bitfld.long 0x00 11. " PABORTS ,Vector Catch Enable Prefetch abort (Secure)" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " SMI ,Vector Catch Enable SMI (Secure)" "Disabled,Enabled" bitfld.long 0x0 7. " FIQ ,Vector Catch Enable FIQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " IRQ ,Vector Catch Enable IRQ" "Disabled,Enabled" bitfld.long 0x0 4. " DABORT0 ,Vector Catch Enable Data Abort" "Disabled,Enabled" textline " " bitfld.long 0x0 3. " PABORT ,Vector Catch Enable Prefetch Abort" "Disabled,Enabled" bitfld.long 0x0 2. " SWI ,Vector Catch Enable SWI" "Disabled,Enabled" textline " " bitfld.long 0x0 1. " UNDEF ,Vector Catch Enable Undefined Instruction" "Disabled,Enabled" bitfld.long 0x0 0. " RESET ,Vector Catch Enable Reset" "Disabled,Enabled" endif hgroup c14:0x020--0x020 hide.long 0x0 "DBGDTRRX,Debug Receive Register (External View)" in group c14:0x023--0x023 line.long 0x0 "DBGDTRTX,Debug Transmit Register (External View)" group c14:0x09++0x00 line.long 0x00 "DBGECR,Event Catch Register" bitfld.long 0x00 0. " OSUC ,OS Unlock Catch" "Disabled,Enabled" group c14:0x0a++0x00 line.long 0x00 "DBGDSCCR,Debug State Cache Control Register" bitfld.long 0x00 2. " NWT ,Not Write-Through" "Forced,Normal" bitfld.long 0x00 0. " DUCL ,Data and Unified Cache Linefill" "Disabled,Normal" wgroup c14:0x21++0x00 line.long 0x00 "DBGITR,Instruction Transfer Register" rgroup c14:0x21++0x00 line.long 0x00 "DBGPCSR,Program Counter Sampling Register" hexmask.long 0x00 2.--31. 1. " PCSV ,Program Counter sample value" bitfld.long 0x00 0.--1. " MPCSV ,Meaning of PC sample value" "ARM,Thumb,Jazelle,Thumb" wgroup c14:0x24++0x00 line.long 0x00 "DBGDRCR,Debug Run Control Register" bitfld.long 0x00 3. " CSPA ,Clear Sticky Pipeline Advance" "Not cleared,Cleared" bitfld.long 0x00 2. " CSE ,Clear Sticky Exceptions" "Not cleared,Cleared" textline " " bitfld.long 0x00 1. " RR ,Restart Request" "Not requested,Requested" bitfld.long 0x00 0. " HR ,Halt Request" "Not requested,Requested" wgroup c14:0xc0++0x00 line.long 0x00 "DBGOSLAR,Operating System Lock Access Register" rgroup c14:0xc1++0x00 line.long 0x00 "DBGOSLSR,Operating System Lock Status Register" bitfld.long 0x00 2. " 32_BA ,32-Bit Access" "Not required,Required" bitfld.long 0x00 1. " LB ,Locked Bit" "Not locked,Locked" bitfld.long 0x00 0. " LIB ,Lock Implemented Bit" "Not implemented,Implemented" group c14:0xc2++0x00 line.long 0x00 "DBGOSSRR,Operating System Save and Restore Register" hexmask.long 0x00 0.--31. 1. " OSSR ,OS Save and Restore" group c14:0xc4++0x00 line.long 0x00 "DBGPRCR,Device Power-Down and Reset Control Register" bitfld.long 0x00 0. " NPD ,No Power-Down" "DBGNOPWRDWN low,DBGNOPWRDWN high" group c14:0xc5++0x00 line.long 0x00 "DBGPRSR,Device Power-Down and Reset Status Register" bitfld.long 0x00 3. " SR ,Sticky Reset Status" "Not reset,Reset" bitfld.long 0x00 2. " R ,Reset Status" "No reset,Reset" textline " " bitfld.long 0x00 1. " SPD ,Sticky Power-down Status" "Not reset,Reset" bitfld.long 0x00 0. " PU ,Power-up Status" "Powered down,Powered up" width 11. tree "Processor Identifier Registers" rgroup c14:0x340--0x340 line.long 0x00 "CPUID,Main ID Register" hexmask.long.byte 0x0 24.--31. 0x1 " IMPL ,Implementer code" hexmask.long.byte 0x0 20.--23. 0x1 " SPECREV ,Variant number" textline " " hexmask.long.byte 0x0 16.--19. 0x1 " ARCH ,Architecture" hexmask.long.word 0x0 4.--15. 0x1 " PARTNUM ,Part Number" textline " " hexmask.long.byte 0x0 0.--3. 0x1 " REV ,Layout Revision" rgroup c14:0x341--0x341 line.long 0x00 "CACHETYPE,Cache Type Register" bitfld.long 0x0 29.--31. " FORMAT ,Format" "Not ARMv7,Not ARMv7,Not ARMv7,Not ARMv7,ARMv7,Not ARMv7,Not ARMv7,Not ARMv7" bitfld.long 0x0 24.--27. " CWG ,Cache Writeback Granule" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x0 20.--23. " ERG ,Exclusives Reservation Granule" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 16.--19. " DMinLine ,Words of Smallest Line Length in L1 or L2 Data Cache Number" "Reserved,Reserved,Reserved,Reserved,16x32-bit words,?..." textline " " bitfld.long 0x00 14.--15. " L1_IPOLICY ,VIPT Instruction Cache Support" "Reserved,Reserved,Supported,?..." bitfld.long 0x00 0.--3. " IMINLINE ,Words of Smallest Line Length in L1 or L2 Instruction Cache Number" "Reserved,Reserved,Reserved,Reserved,16x32-bit words,?..." rgroup c14:0x343--0x343 line.long 0x00 "TLBTYPE,TLB Type Register" hexmask.long.byte 0x0 16.--23. 0x1 " ILSIZE ,Specifies the number of instruction TLB lockable entries" hexmask.long.byte 0x0 8.--15. 0x1 " DLSIZE ,Specifies the number of unified or data TLB lockable entries" textline " " bitfld.long 0x0 1. " TLB_SIZE ,TLB Size" "64,128" bitfld.long 0x0 0. " U ,Unified or separate instruction TLBs" "Unified,Separate" rgroup c14:0x348--0x348 line.long 0x00 "ID_PFR0,Processor Feature Register 0" bitfld.long 0x00 12.--15. " STATE3 ,Thumb-2 Execution Environment (Thumb-2EE) Support" "Reserved,Supported,?..." bitfld.long 0x00 8.--11. " STATE2 ,Java Extension Interface Support" "Reserved,Reserved,Supported,?..." textline " " bitfld.long 0x00 4.--7. " STATE1 ,Thumb Encoding Supported by the Processor Type" "Reserved,Reserved,Reserved,Supported,?..." bitfld.long 0x00 0.--3. " STATE0 ,ARM Instruction Set Support" "Reserved,Supported,?..." rgroup c14:0x349--0x349 line.long 0x00 "ID_PFR1,Processor Feature Register 1" bitfld.long 0x00 8.--11. " MPM ,Microcontroller Programmer's Model Support" "Not supported,?..." bitfld.long 0x00 4.--7. " SE ,Security Extensions Architecture v1 Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 0.--3. " PM ,Standard ARMv4 Programmer's Model Support" "Reserved,Supported,?..." rgroup c14:0x34a--0x34a line.long 0x00 "ID_DFR0,Debug Feature Register 0" bitfld.long 0x00 20.--23. " MDM_MM ,Microcontroller Debug Model Support" "Not supported,?..." bitfld.long 0x00 16.--19. " TDM_MM ,Trace Debug Model (Memory-Mapped) Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 12.--15. " TDM_CB ,Coprocessor-Based Trace Debug Model Support" "Not supported,?..." bitfld.long 0x00 8.--11. " CDM_MM ,Memory-Mapped Debug Model Support" "Reserved,Reserved,Reserved,Reserved,Supported,?..." textline " " bitfld.long 0x00 4.--7. " SDM_CB ,Secure Debug Model (Coprocessor) Support" "Reserved,Reserved,Reserved,Reserved,Supported,?..." bitfld.long 0x00 0.--3. " CDM_CB ,Coprocessor Debug Model Support" "Reserved,Reserved,Reserved,Reserved,Supported,?..." rgroup c14:0x34b--0x34b line.long 0x00 "ID_AFR0,Auxiliary Feature Register 0" hexmask.long 0x00 0.--31. 1. " AF ,Auxiliary Feature" rgroup c14:0x34c--0x34c line.long 0x00 "ID_MMFR0,Processor Feature Register 0" bitfld.long 0x00 24.--27. " FCSE ,Fast Context Switch Memory Mappings Support" "Not supported,?..." bitfld.long 0x00 20.--23. " ACR ,Auxiliary Control Register Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 16.--19. " TCM ,TCM and Associated DMA Support" "Not supported,?..." bitfld.long 0x00 12.--15. " OSS ,Outer Shareable Support" "Not supported,?..." textline " " bitfld.long 0x00 8.--11. " CC_CPUA ,Cache Coherency Support" "Reserved,Supported,?..." bitfld.long 0x00 4.--7. " PMSA ,Physical Memory System Architecture (PMSA) Support" "Not supported,?..." textline " " bitfld.long 0x00 0.--3. " VMSA ,Virtual Memory System Architecture (VMSA) Support" "Reserved,Reserved,Reserved,Supported,?..." rgroup c14:0x34d--0x34d line.long 0x00 "ID_MMFR1,Processor Feature Register 1" bitfld.long 0x00 28.--31. " BTB ,Branch Predictor" "Reserved,Reserved,Required,?..." bitfld.long 0x00 24.--27. " L1TCO ,Test and Clean Operations on Data Cache/Harvard/Unified Architecture Support" "Not supported,?..." textline " " bitfld.long 0x00 20.--23. " L1UCMO ,L1 Cache/All Maintenance Operations/Unified Architecture Support" "Not supported,?..." bitfld.long 0x00 16.--19. " L1HCMO ,L1 Cache/All Maintenance Operations/Harvard Architecture Support" "Not supported,?..." textline " " bitfld.long 0x00 12.--15. " L1UCLMOSW ,L1 Cache Line Maintenance Operations by Set and Way/Unified Architecture Support" "Not supported,?..." bitfld.long 0x00 8.--11. " L1HCLMOSW ,L1 Cache Line Maintenance Operations by Set and Way/Harvard Architecture Support" "Not supported,?..." textline " " bitfld.long 0x00 4.--7. " L1UCLMOMVA ,L1 Cache Line Maintenance Operations by VA/Unified Architecture Support" "Not supported,?..." bitfld.long 0x00 0.--3. " L1HCLMOMVA ,L1 Cache Line Maintenance Operations by VA/Harvard Architecture" "Not supported,?..." rgroup c14:0x34e--0x34e line.long 0x00 "ID_MMFR2,Processor Feature Register 2" bitfld.long 0x00 28.--31. " HAF ,Hardware Access Flag Support" "Not supported,?..." bitfld.long 0x00 24.--27. " WFI ,Wait for Interrupt Stalling Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 20.--23. " MBF ,Memory Barrier Operations Support" "Reserved,Reserved,Supported,?..." bitfld.long 0x00 16.--19. " UTLBMO ,TLB Maintenance Operations/Unified Architecture Support" "Reserved,Reserved,Reserved,Supported,?..." textline " " bitfld.long 0x00 12.--15. " HTLBMO ,TLB Maintenance Operations/Harvard Architecture Support" "Not supported,?..." bitfld.long 0x00 8.--11. " HL1CMRO ,Cache Maintenance Range Operations/Harvard Architecture Support" "Not supported,?..." textline " " bitfld.long 0x00 4.--7. " HL1BPCRO ,Background Prefetch Cache Range Operations/Harvard Architecture Support" "Not supported,?..." bitfld.long 0x00 0.--3. " HL1FPCRO ,Foreground Prefetch Cache Range Operations/Harvard Architecture Support" "Not supported,?..." rgroup c14:0x34f--0x34f line.long 0x00 "ID_MMFR3,Processor Feature Register 3" bitfld.long 0x00 28.--31. " SS ,Supersection support" "Supported,?..." bitfld.long 0x00 20.--23. " CW ,Coherent walk" "Supported,?..." textline " " bitfld.long 0x00 12.--15. " MB ,Invalidate broadcast Support" "Reserved,Reserved,Supported,?..." bitfld.long 0x00 8.--11. " BPM ,Invalidate Branch predictor Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 4.--7. " HCMOSW ,Invalidate Cache by Set and Way/Clean by Set and Way/Invalidate and Clean by Set and Way Support" "Reserved,Supported,?..." bitfld.long 0x00 0.--3. " HCMOMVA ,Invalidate Cache MVA Support" "Reserved,Supported,?..." rgroup c14:0x350--0x350 line.long 0x00 "ID_ISAR0,ISA Feature Register 0" bitfld.long 0x00 24.--27. " DIVI ,Divide Instructions Support" "Not supported,?..." bitfld.long 0x00 20.--23. " DEBI ,Debug Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 16.--19. " CI ,Coprocessor Instructions Support" "Not supported,?..." bitfld.long 0x00 12.--15. " CBI ,Combined Compare and Branch Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 8.--11. " BI ,Bitfield Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 4.--7. " BCI ,Bit Counting Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 0.--3. " SI ,Swap Instructions Support" "Reserved,Supported,?..." rgroup c14:0x351--0x351 line.long 0x00 "ID_ISAR1,ISA Feature Register 1" bitfld.long 0x00 28.--31. " JI ,Jazelle Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 24.--27. " INTI ,Interwork Instructions Support" "Reserved,Reserved,Reserved,Supported,?..." textline " " bitfld.long 0x00 20.--23. " IMMI ,Immediate Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 16.--19. " ITEI ,If Then Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 12.--15. " EXTI ,Extend Instructions Support" "Reserved,Reserved,Supported,?..." bitfld.long 0x00 8.--11. " E2I ,Exception 2 Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 4.--7. " E1I ,Exception 1 Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 0.--3. " ENDI ,Endian Instructions Support" "Reserved,Supported,?..." rgroup c14:0x352--0x352 line.long 0x00 "ID_ISAR2,ISA Feature Register 2" bitfld.long 0x00 28.--31. " RI ,Reversal Instructions Support" "Reserved,Reserved,Supported,?..." bitfld.long 0x00 24.--27. " PSRI ,PSR Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 20.--23. " UMI ,Advanced Unsigned Multiply Instructions Support" "Reserved,Reserved,Supported,?..." bitfld.long 0x00 16.--19. " SMI ,Advanced Signed Multiply Instructions Support" "Reserved,Reserved,Reserved,Supported,?..." textline " " bitfld.long 0x00 12.--15. " MI ,Multiply Instructions Support" "Reserved,Reserved,Supported,?..." bitfld.long 0x00 8.--11. " II ,Multi-Access Interruptible Instructions Support" "Not supported,?..." textline " " bitfld.long 0x00 4.--7. " MHI ,Memory Hint Instructions Support" "Reserved,Reserved,Reserved,Supported,?..." bitfld.long 0x00 0.--3. " LSI ,Load and Store Instructions Support" "Reserved,Supported,?..." rgroup c14:0x353--0x353 line.long 0x00 "ID_ISAR3,ISA Feature Register 3" bitfld.long 0x00 28.--31. " T2E ,Thumb-2 Extensions Support" "Reserved,Supported,?..." bitfld.long 0x00 24.--27. " NOPI ,True NOP Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 20.--23. " TCI ,Thumb Copy Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 16.--19. " TBI ,Table Branch Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 12.--15. " SPI ,Synchronization Primitive Instructions Support" "Reserved,Reserved,Supported,?..." bitfld.long 0x00 8.--11. " SVCI ,SVC Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 4.--7. " SIMDI ,Single Instruction Multiple Data (SIMD) Instructions Support" "Reserved,Reserved,Reserved,Supported,?..." bitfld.long 0x00 0.--3. " SI ,Saturate Instructions Support" "Reserved,Supported,?..." rgroup c14:0x354--0x354 line.long 0x00 "ID_ISAR4,ISA Feature Register 4" bitfld.long 0x00 28.--31. " SWP_frac ,SWAP_frac" "Supported,?..." bitfld.long 0x00 24.--27. " PSR_M_I ,PSR_M Instructions Support" "Not supported,?..." textline " " bitfld.long 0x00 20.--23. " SPRI ,Synchronization Primitive instructions" "Not supported,?..." bitfld.long 0x00 16.--19. " BI ,Barrier Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 12.--15. " SMCI ,SMC Instructions Support" "Reserved,Supported,?..." bitfld.long 0x00 8.--11. " WBI ,Write-Back Instructions Support" "Reserved,Supported,?..." textline " " bitfld.long 0x00 4.--7. " WSI ,With-Shift Instructions Support" "Reserved,Reserved,Reserved,Reserved,Supported,?..." bitfld.long 0x00 0.--3. " UI ,Unprivileged Instructions Support" "Reserved,Reserved,Supported,?..." rgroup c14:0x355--0x355 line.long 0x00 "ID_ISAR5,ISA Feature Register 5" tree.end width 17. tree "Coresight Management Registers" textline " " group c14:0x03bd++0x00 line.long 0x00 "DBGITCTRL_IOC,Integration Internal Output Control Register" bitfld.long 0x00 5. " I_DBGTRIGGER ,Internal DBGTRIGGER" "0,1" bitfld.long 0x00 4. " I_DBGRESTARTED ,Internal DBGRESTARTED" "0,1" textline " " bitfld.long 0x00 3. " I_nPMUIRQ ,Internal nPMUIRQ" "0,1" bitfld.long 0x00 2. " InternalCOMMTX ,Internal COMMTX" "0,1" textline " " bitfld.long 0x00 1. " I_COMMRX ,Internal COMMRX" "0,1" bitfld.long 0x00 0. " I_DBGACK ,Internal DBGACK" "0,1" group c14:0x03be++0x00 line.long 0x00 "DBGITCTRL_EOC,Integration External Output Control Register" bitfld.long 0x00 7. " nDMAEXTERRIQ ,External nDMAEXTERRIRQ" "0,1" bitfld.long 0x00 6. " nDMASIRQ ,External nDMASIRQ" "0,1" textline " " bitfld.long 0x00 5. " nDMAIRQ ,External nDMAIRQ" "0,1" bitfld.long 0x00 4. " nPMUIRQ ,External nPMUIRQ" "0,1" textline " " bitfld.long 0x00 3. " STANDBYWFI ,External STANDBYWFI" "0,1" bitfld.long 0x00 2. " COMMTX ,External COMMTX" "0,1" textline " " bitfld.long 0x00 1. " COMMRX ,External COMMRX" "0,1" bitfld.long 0x00 0. " DBGACK ,External DBGACK" "0,1" rgroup c14:0x03bf++0x00 line.long 0x00 "DBGITCTRL_IS,Integration Input Status Register" bitfld.long 0x00 11. " CTI_DBGRESTART ,CTI Debug Restart" "0,1" bitfld.long 0x00 10. " CTI_EDBGRQ ,CTI Debug Request" "0,1" textline " " bitfld.long 0x00 9. " CTI_PMUEXTIN[1] ,CTI PMUEXTIN[1] Signal" "0,1" bitfld.long 0x00 8. " CTI_PMUEXTIN[0] ,CTI PMUEXTIN[0] Signal" "0,1" textline " " bitfld.long 0x00 2. " nFIQ ,nFIQ Input" "0,1" bitfld.long 0x00 1. " nIRQ ,nIRQ Input" "0,1" textline " " bitfld.long 0x00 0. " EDBGRQ ,EDBGRQ Input" "0,1" group c14:0x3c0--0x3c0 line.long 0x0 "DBGITCTRL,Integration Mode Control Register" bitfld.long 0x0 0. " IME ,Integration Mode Enable" "Disabled,Enabled" group c14:0x3e8--0x3e8 line.long 0x0 "DBGCLAIMSET,Claim Tag Set Register" bitfld.long 0x0 7. " CT7 ,Claim Tag 7" "No Effect,Set" bitfld.long 0x0 6. " CT6 ,Claim Tag 6" "No Effect,Set" textline " " bitfld.long 0x0 5. " CT5 ,Claim Tag 5" "No Effect,Set" bitfld.long 0x0 4. " CT4 ,Claim Tag 4" "No Effect,Set" textline " " bitfld.long 0x0 3. " CT3 ,Claim Tag 3" "No Effect,Set" bitfld.long 0x0 2. " CT2 ,Claim Tag 2" "No Effect,Set" textline " " bitfld.long 0x0 1. " CT1 ,Claim Tag 1" "No Effect,Set" bitfld.long 0x0 0. " CT0 ,Claim Tag 0" "No Effect,Set" group c14:0x3e9--0x3e9 line.long 0x0 "DBGCLAIMCLR,Claim Tag Clear Register" bitfld.long 0x0 7. " CT7 ,Claim Tag 7" "No Effect,Cleared" bitfld.long 0x0 6. " CT6 ,Claim Tag 6" "No Effect,Cleared" textline " " bitfld.long 0x0 5. " CT5 ,Claim Tag 5" "No Effect,Cleared" bitfld.long 0x0 4. " CT4 ,Claim Tag 4" "No Effect,Cleared" textline " " bitfld.long 0x0 3. " CT3 ,Claim Tag 3" "No Effect,Cleared" bitfld.long 0x0 2. " CT2 ,Claim Tag 2" "No Effect,Cleared" textline " " bitfld.long 0x0 1. " CT1 ,Claim Tag 1" "No Effect,Cleared" bitfld.long 0x0 0. " CT0 ,Claim Tag 0" "No Effect,Cleared" wgroup c14:0x3ec--0x3ec line.long 0x0 "DBGLAR,Lock Access Register" rgroup c14:0x3ed--0x3ed line.long 0x0 "DBGLSR,Lock Status Register" bitfld.long 0x00 2. " NTT ,Not 32-bit access" "32-bit,Not 32-bit" bitfld.long 0x00 1. " SLK ,Software Lock status" "Not locked,Locked" textline " " bitfld.long 0x00 0. " SLI ,Software Lock Implemented" "Not implemented,Implemented" rgroup c14:0x3ee--0x3ee line.long 0x0 "DBGAUTHSTATUS,Debug Authentication Status Register" bitfld.long 0x00 7. " SNI ,Secure non-invasive debug features implementation" "No effect,Implemented" bitfld.long 0x00 6. " SNE ,Secure non-invasive debug enable (DBGEN OR NIDEN) AND (SPIDEN OR SPNIDEN)" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " SI ,Secure invasive debug features implementation" "No effect,Implemented" bitfld.long 0x00 4. " SE ,Secure invasive debug enable (DBGEN AND SPIDEN)" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " NSNI ,Non-secure non-invasive debug features implementation" "Not implemented,Implemented" bitfld.long 0x00 2. " NSNE ,Non-secure non-invasive debug enable (DBGEN OR NIDEN)" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " NSI ,Non-secure invasive debug features implementation" "Not implemented,Implemented" bitfld.long 0x00 0. " NSE ,Non-secure invasive debug enable (DBGEN)" "Disabled,Enabled" hgroup c14:0x3f2--0x3f2 hide.long 0x0 "DBGDEVID,Device Identifier (RESERVED)" rgroup c14:0x3f3--0x3f3 line.long 0x0 "DBGDEVTYPE,Device Type" bitfld.long 0x00 4.--7. " T ,Sub type" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 0.--3. " C ,Main class" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" rgroup c14:0x3f8--0x3f8 line.long 0x00 "DBGPID0,Debug Peripheral ID 0" hexmask.long.byte 0x00 0.--7. 1. " PN[7:0] ,Part Number [7:0]" rgroup c14:0x3f9--0x3f9 line.long 0x00 "DBGPID1,Debug Peripheral ID 1" hexmask.long.byte 0x00 4.--7. 1. " JEPID[3:0] ,JEP Identity Code[3:0]" hexmask.long.byte 0x00 0.--3. 1. " PN[11:8] ,Part Number [11:8]" rgroup c14:0x3fa--0x3fa line.long 0x00 "DBGPID2,Debug Peripheral ID 2" hexmask.long.byte 0x00 4.--7. 1. " REV ,Revision" bitfld.long 0x00 3. " UJEPCODE ,Uses JEP Code" "Disabled,Enabled" hexmask.long.byte 0x00 0.--2. 1. " JEPID[6:4] ,JEP Identity Code[6:4]" rgroup c14:0x3fb--0x3fb line.long 0x00 "DBGPID3,Debug Peripheral ID 3" hexmask.long.byte 0x00 4.--7. 1. " REVAND ,Manufacturing revision" hexmask.long.byte 0x00 0.--3. 1. " CM ,Customer modified" rgroup c14:0x3f4--0x3f4 line.long 0x00 "DBGPID4,Debug Peripheral ID 4" hexmask.long.byte 0x00 4.--7. 1. " 4KB_COUNT ,4KB count" hexmask.long.byte 0x00 0.--3. 1. " JEP106_CONT_CODE ,JEP 106 Continuation code" rgroup c14:0x3fc--0x3fc line.long 0x00 "DBGCID0,Debug Component ID 0" hexmask.long.byte 0x00 0.--7. 1. " PREAMBLE ,Preamble byte 0" rgroup c14:0x3fd--0x3fd line.long 0x00 "DBGCID1,Debug Component ID 1" hexmask.long.byte 0x00 4.--7. 1. " CC ,Component class" hexmask.long.byte 0x00 0.--3. 1. " PREAMBLE ,Preamble byte 1" rgroup c14:0x3fe--0x3fe line.long 0x00 "DBGCID2,Debug Component ID 2" hexmask.long.byte 0x00 0.--7. 1. " PREAMBLE ,Preamble byte 2" rgroup c14:0x3ff--0x3ff line.long 0x00 "DBGCID3,Debug Component ID 3" hexmask.long.byte 0x00 0.--7. 1. " PREAMBLE ,Preamble byte 3" tree.end tree.end width 6. tree "Breakpoint Registers" group c14:0x40++0x00 line.long 0x00 "BVR0,Breakpoint Value Register 0" group c14:0x50++0x00 line.long 0x00 "BCR0,Breakpoint Control Register 0" bitfld.long 0x00 20.--22. " M ,BVR Meaning" "IVA match,Linked IVA match,Reserved,Reserved,IVA mismatch,Linked IVA mismatch,?..." bitfld.long 0x00 16.--19. " LBRP ,Linked BRP Number" "BRP,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15" bitfld.long 0x00 14.--15. " SWAC ,Secure World Access Control" "Both,Nonsecure,Secure,?..." textline " " bitfld.long 0x0 8. " BAS ,Byte 3 address select" "0,1" bitfld.long 0x0 7. ",Byte 2 address select" "0,1" bitfld.long 0x0 6. ",Byte 1 address select" "0,1" bitfld.long 0x0 5. ",Byte 0 address select" "0,1" bitfld.long 0x00 1.--2. " S ,Supervisor Access Control" "User/system/supervisor,Privileged,User,Any" bitfld.long 0x00 0. " B ,Breakpoint Enable" "Disabled,Enabled" group c14:0x41++0x00 line.long 0x00 "BVR1,Breakpoint Value Register 1" group c14:0x51++0x00 line.long 0x00 "BCR1,Breakpoint Control Register 1" bitfld.long 0x00 20.--22. " M ,BVR Meaning" "IVA match,Linked IVA match,Reserved,Reserved,IVA mismatch,Linked IVA mismatch,?..." bitfld.long 0x00 16.--19. " LBRP ,Linked BRP Number" "BRP,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15" bitfld.long 0x00 14.--15. " SWAC ,Secure World Access Control" "Both,Nonsecure,Secure,?..." textline " " bitfld.long 0x0 8. " BAS ,Byte 3 address select" "0,1" bitfld.long 0x0 7. ",Byte 2 address select" "0,1" bitfld.long 0x0 6. ",Byte 1 address select" "0,1" bitfld.long 0x0 5. ",Byte 0 address select" "0,1" bitfld.long 0x00 1.--2. " S ,Supervisor Access Control" "User/system/supervisor,Privileged,User,Any" bitfld.long 0x00 0. " B ,Breakpoint Enable" "Disabled,Enabled" group c14:0x42++0x00 line.long 0x00 "BVR2,Breakpoint Value Register 2" group c14:0x52++0x00 line.long 0x00 "BCR2,Breakpoint Control Register 2" bitfld.long 0x00 20.--22. " M ,BVR Meaning" "IVA match,Linked IVA match,Reserved,Reserved,IVA mismatch,Linked IVA mismatch,?..." bitfld.long 0x00 16.--19. " LBRP ,Linked BRP Number" "BRP,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15" bitfld.long 0x00 14.--15. " SWAC ,Secure World Access Control" "Both,Nonsecure,Secure,?..." textline " " bitfld.long 0x0 8. " BAS ,Byte 3 address select" "0,1" bitfld.long 0x0 7. ",Byte 2 address select" "0,1" bitfld.long 0x0 6. ",Byte 1 address select" "0,1" bitfld.long 0x0 5. ",Byte 0 address select" "0,1" bitfld.long 0x00 1.--2. " S ,Supervisor Access Control" "User/system/supervisor,Privileged,User,Any" bitfld.long 0x00 0. " B ,Breakpoint Enable" "Disabled,Enabled" group c14:0x43++0x00 line.long 0x00 "BVR3,Breakpoint Value Register 3" group c14:0x53++0x00 line.long 0x00 "BCR3,Breakpoint Control Register 3" bitfld.long 0x00 20.--22. " M ,BVR Meaning" "IVA match,Linked IVA match,Reserved,Reserved,IVA mismatch,Linked IVA mismatch,?..." bitfld.long 0x00 16.--19. " LBRP ,Linked BRP Number" "BRP,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15" bitfld.long 0x00 14.--15. " SWAC ,Secure World Access Control" "Both,Nonsecure,Secure,?..." textline " " bitfld.long 0x0 8. " BAS ,Byte 3 address select" "0,1" bitfld.long 0x0 7. ",Byte 2 address select" "0,1" bitfld.long 0x0 6. ",Byte 1 address select" "0,1" bitfld.long 0x0 5. ",Byte 0 address select" "0 ,1" bitfld.long 0x00 1.--2. " S ,Supervisor Access Control" "User/system/supervisor,Privileged,User,Any" bitfld.long 0x00 0. " B ,Breakpoint Enable" "Disabled,Enabled" group c14:0x44++0x00 line.long 0x00 "BVR4,Breakpoint Value Register 4" group c14:0x54++0x00 line.long 0x00 "BCR4,Breakpoint Control Register 4" bitfld.long 0x00 20.--22. " M ,BVR Meaning" "IVA match,Linked IVA match,Unlinked ID,Linked ID,IVA mismatch,Linked IVA mismatch,?..." bitfld.long 0x00 16.--19. " LBRP ,Linked BRP Number" "BRP,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15" bitfld.long 0x00 14.--15. " SWAC ,Secure World Access Control" "Both,Nonsecure,Secure,?..." textline " " bitfld.long 0x0 8. " BAS ,Byte 3 address select" "0,1" bitfld.long 0x0 7. ",Byte 2 address select" "0,1" bitfld.long 0x0 6. ",Byte 1 address select" "0,1" bitfld.long 0x0 5. ",Byte 0 address select" "0,1" bitfld.long 0x00 1.--2. " S ,Supervisor Access Control" "User/system/supervisor,Privileged,User,Any" bitfld.long 0x00 0. " B ,Breakpoint Enable" "Disabled,Enabled" group c14:0x45++0x00 line.long 0x00 "BVR5,Breakpoint Value Register 5" group c14:0x55++0x00 line.long 0x00 "BCR5,Breakpoint Control Register 5" bitfld.long 0x00 20.--22. " M ,BVR Meaning" "IVA match,Linked IVA match,Unlinked ID,Linked ID,IVA mismatch,Linked IVA mismatch,?..." bitfld.long 0x00 16.--19. " LBRP ,Linked BRP Number" "BRP,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15" bitfld.long 0x00 14.--15. " SWAC ,Secure World Access Control" "Both,Nonsecure,Secure,?..." textline " " bitfld.long 0x0 8. " BAS ,Byte 3 address select" "0,1" bitfld.long 0x0 7. ",Byte 2 address select" "0,1" bitfld.long 0x0 6. ",Byte 1 address select" "0,1" bitfld.long 0x0 5. ",Byte 0 address select" "0,1" bitfld.long 0x00 1.--2. " S ,Supervisor Access Control" "User/system/supervisor,Privileged,User,Any" bitfld.long 0x00 0. " B ,Breakpoint Enable" "Disabled,Enabled" tree.end width 6. tree "Watchpoint Control Registers" group c14:0x60++0x00 line.long 0x00 "WVR0,Watchpoint Value Register 0" hexmask.long 0x00 2.--31. 0x04 " WA0 ,Watchpoint Address 0" group c14:0x70--0x70 line.long 0x0 "WCR0,Watchpoint Control Register 0" bitfld.long 0x0 24.--28. " WAM ,Watchpoint address mask" "Not masked,Reserved,Reserved,0x7,0xF,0x1F,0x3F,0x7F,0xFF,0x1FF,0x3FF,0x7FF,0xFFF,0x1FFF,0x3FFF,0x7FFF,0xFFFF,0x1FFFF,0x3FFFF,0x7FFFF,0xFFFFF,0x1FFFFF,0x3FFFFF,0x7FFFFF,0xFFFFFF,0x1FFFFFF,0x3FFFFFF,0x7FFFFFF,0xFFFFFFF,0x1FFFFFFF,0x3FFFFFFF,0x7FFFFFFF" bitfld.long 0x0 20. " EL ,Enable Linking" "Disabled,Enabled" textline " " bitfld.long 0x0 16.--19. " LBN ,Linked BRP number" "BRP,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15" bitfld.long 0x0 14.--15. " SWAC ,Secure world access control" "Non-secure & Secure,Non-secure,Secure,?..." textline " " bitfld.long 0x0 12. " BAS ,Byte 7 address select" "0,1" bitfld.long 0x0 11. ",Byte 6 address select" "0,1" bitfld.long 0x0 10. ",Byte 5 address select" "0,1" bitfld.long 0x0 9. ",Byte 4 address select" "0,1" bitfld.long 0x0 8. ",Byte 3 address select" "0,1" bitfld.long 0x0 7. ",Byte 2 address select" "0,1" bitfld.long 0x0 6. ",Byte 1 address select" "0,1" bitfld.long 0x0 5. ",Byte 0 address select" "0,1" textline " " bitfld.long 0x0 3.--4. " RD/WR ,Load/Store access control" "Reserved,Load,Store,Any" bitfld.long 0x0 1.--2. " PAC ,Privileged access control" "Reserved,Privileged,USR,Any" textline " " bitfld.long 0x0 0. " WE ,Watchpoint enable" "Disabled,Enabled" group c14:0x61++0x00 line.long 0x00 "WVR1,Watchpoint Value Register 1" hexmask.long 0x00 2.--31. 0x04 " WA1 ,Watchpoint Address 1" group c14:0x71--0x71 line.long 0x0 "WCR1,Watchpoint Control Register 1" bitfld.long 0x0 24.--28. " WAM ,Watchpoint address mask" "Not masked,Reserved,Reserved,0x7,0xF,0x1F,0x3F,0x7F,0xFF,0x1FF,0x3FF,0x7FF,0xFFF,0x1FFF,0x3FFF,0x7FFF,0xFFFF,0x1FFFF,0x3FFFF,0x7FFFF,0xFFFFF,0x1FFFFF,0x3FFFFF,0x7FFFFF,0xFFFFFF,0x1FFFFFF,0x3FFFFFF,0x7FFFFFF,0xFFFFFFF,0x1FFFFFFF,0x3FFFFFFF,0x7FFFFFFF" bitfld.long 0x0 20. " EL ,Enable Linking" "Disabled,Enabled" textline " " bitfld.long 0x0 16.--19. " LBN ,Linked BRP number" "BRP,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15" bitfld.long 0x0 14.--15. " SWAC ,Secure world access control" "Non-secure & Secure,Non-secure,Secure,?..." textline " " bitfld.long 0x0 12. " BAS ,Byte 7 address select" "0,1" bitfld.long 0x0 11. ",Byte 6 address select" "0,1" bitfld.long 0x0 10. ",Byte 5 address select" "0,1" bitfld.long 0x0 9. ",Byte 4 address select" "0,1" bitfld.long 0x0 8. ",Byte 3 address select" "0,1" bitfld.long 0x0 7. ",Byte 2 address select" "0,1" bitfld.long 0x0 6. ",Byte 1 address select" "0,1" bitfld.long 0x0 5. ",Byte 0 address select" "0,1" textline " " bitfld.long 0x0 3.--4. " RD/WR ,Load/Store access control" "Reserved,Load,Store,Any" bitfld.long 0x0 1.--2. " PAC ,Privileged access control" "Reserved,Privileged,USR,Any" textline " " bitfld.long 0x0 0. " WE ,Watchpoint enable" "Disabled,Enabled" group c14:0x62++0x00 line.long 0x00 "WVR2,Watchpoint Value Register 2" hexmask.long 0x00 2.--31. 0x04 " WA2 ,Watchpoint Address 2" group c14:0x72--0x72 line.long 0x0 "WCR2,Watchpoint Control Register 2" bitfld.long 0x0 24.--28. " WAM ,Watchpoint address mask" "Not masked,Reserved,Reserved,0x7,0xF,0x1F,0x3F,0x7F,0xFF,0x1FF,0x3FF,0x7FF,0xFFF,0x1FFF,0x3FFF,0x7FFF,0xFFFF,0x1FFFF,0x3FFFF,0x7FFFF,0xFFFFF,0x1FFFFF,0x3FFFFF,0x7FFFFF,0xFFFFFF,0x1FFFFFF,0x3FFFFFF,0x7FFFFFF,0xFFFFFFF,0x1FFFFFFF,0x3FFFFFFF,0x7FFFFFFF" bitfld.long 0x0 20. " EL ,Enable Linking" "Disabled,Enabled" textline " " bitfld.long 0x0 16.--19. " LBN ,Linked BRP number" "BRP,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15" bitfld.long 0x0 14.--15. " SWAC ,Secure world access control" "Non-secure & Secure,Non-secure,Secure,?..." textline " " bitfld.long 0x0 12. " BAS ,Byte 7 address select" "0,1" bitfld.long 0x0 11. ",Byte 6 address select" "0,1" bitfld.long 0x0 10. ",Byte 5 address select" "0,1" bitfld.long 0x0 9. ",Byte 4 address select" "0,1" bitfld.long 0x0 8. ",Byte 3 address select" "0,1" bitfld.long 0x0 7. ",Byte 2 address select" "0,1" bitfld.long 0x0 6. ",Byte 1 address select" "0,1" bitfld.long 0x0 5. ",Byte 0 address select" "0,1" textline " " bitfld.long 0x0 3.--4. " RD/WR ,Load/Store access control" "Reserved,Load,Store,Any" bitfld.long 0x0 1.--2. " PAC ,Privileged access control" "Reserved,Privileged,USR,Any" textline " " bitfld.long 0x0 0. " WE ,Watchpoint enable" "Disabled,Enabled" group c14:0x63++0x00 line.long 0x00 "WVR3,Watchpoint Value Register 3" hexmask.long 0x00 2.--31. 0x04 " WA3 ,Watchpoint Address 3" group c14:0x73--0x73 line.long 0x0 "WCR3,Watchpoint Control Register 3" bitfld.long 0x0 24.--28. " WAM ,Watchpoint address mask" "Not masked,Reserved,Reserved,0x7,0xF,0x1F,0x3F,0x7F,0xFF,0x1FF,0x3FF,0x7FF,0xFFF,0x1FFF,0x3FFF,0x7FFF,0xFFFF,0x1FFFF,0x3FFFF,0x7FFFF,0xFFFFF,0x1FFFFF,0x3FFFFF,0x7FFFFF,0xFFFFFF,0x1FFFFFF,0x3FFFFFF,0x7FFFFFF,0xFFFFFFF,0x1FFFFFFF,0x3FFFFFFF,0x7FFFFFFF" bitfld.long 0x0 20. " EL ,Enable Linking" "Disabled,Enabled" textline " " bitfld.long 0x0 16.--19. " LBN ,Linked BRP number" "BRP,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15" bitfld.long 0x0 14.--15. " SWAC ,Secure world access control" "Non-secure & Secure,Non-secure,Secure,?..." textline " " bitfld.long 0x0 12. " BAS ,Byte 7 address select" "0,1" bitfld.long 0x0 11. ",Byte 6 address select" "0,1" bitfld.long 0x0 10. ",Byte 5 address select" "0,1" bitfld.long 0x0 9. ",Byte 4 address select" "0,1" bitfld.long 0x0 8. ",Byte 3 address select" "0,1" bitfld.long 0x0 7. ",Byte 2 address select" "0,1" bitfld.long 0x0 6. ",Byte 1 address select" "0,1" bitfld.long 0x0 5. ",Byte 0 address select" "0,1" textline " " bitfld.long 0x0 3.--4. " RD/WR ,Load/Store access control" "Reserved,Load,Store,Any" bitfld.long 0x0 1.--2. " PAC ,Privileged access control" "Reserved,Privileged,USR,Any" textline " " bitfld.long 0x0 0. " WE ,Watchpoint enable" "Disabled,Enabled" group c14:0x006--0x006 line.long 0x0 "WFAR,Watchpoint Fault Address Register" hexmask.long.long 0x00 1.--31. 0x02 " WFAR ,Address of the watchpointed instruction" tree.end width 0x0B tree.end tree "CRG (Clock reset generator)" tree "CRG-P" base ad:0x3E200000 width 8. if (((per.l(ad:0x3E200000))&0x7F)==0x00) group.long 0x00++0x03 line.long 0x00 "CRPLC,PLL Control Register" rbitfld.long 0x00 24. " PLLBYPASS ,PLL bypass mode" "Not bypassed,Bypassed" bitfld.long 0x00 16.--19. " LUWMODE ,PLL lock-up wait time" "64 * TREFCLK,128*TREFCLK,512*TREFCLK,768*TREFCLK,1024*TREFCLK,1536*TREFCLK,2048*TREFCLK,3072*TREFCLK,4096*TREFCLK,6144*TREFCLK,8192*TREFCLK,12288*TREFCLK,16384*TREFCLK,24576*TREFCLK,32768*TREFCLK,49152*TREFCLK" bitfld.long 0x00 8.--11. " PSMODE ,Sets the dividing ratio of the PLL clock frequency" "1,1/2,?..." textline " " bitfld.long 0x00 0.--5. " FBMODE ,Stops operation of the PLL clock" "Stopped,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,Activated" else group.long 0x00++0x03 line.long 0x00 "CRPLC,PLL Control Register" bitfld.long 0x00 24. " PLLBYPASS ,PLL bypass mode" "Not bypassed,Bypassed" bitfld.long 0x00 16.--19. " LUWMODE ,PLL lock-up wait time" "64 * TREFCLK,128*TREFCLK,512*TREFCLK,768*TREFCLK,1024*TREFCLK,1536*TREFCLK,2048*TREFCLK,3072*TREFCLK,4096*TREFCLK,6144*TREFCLK,8192*TREFCLK,12288*TREFCLK,16384*TREFCLK,24576*TREFCLK,32768*TREFCLK,49152*TREFCLK" bitfld.long 0x00 8.--11. " PSMODE ,Sets the dividing ratio of the PLL clock frequency" "1,1/2,?..." textline " " bitfld.long 0x00 0.--5. " FBMODE ,Stops operation of the PLL clock" "Stopped,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,Activated" endif rgroup.long 0x04++0x03 line.long 0x00 "CRRDY,PLL Ready Monitor Register" bitfld.long 0x00 4. " PSRMNT ,PSMODE monitor" "Not used,Used" bitfld.long 0x00 0. " PLLRDY ,PLLREADY monitor" "Not ready,Ready" if (((per.l(ad:0x3E200000))&0x7F)==0x00) group.long 0x08++0x03 line.long 0x00 "CRSTP,Stop Control Register" bitfld.long 0x00 1. " STOPMNT ,Stop mode monitor" "Not in stop mode,In stop mode" bitfld.long 0x00 0. " STOPEN ,Stop mode enable" "Disabled,Enabled" else group.long 0x08++0x03 line.long 0x00 "CRSTP,Stop Control Register" rbitfld.long 0x00 1. " STOPMNT ,Stop mode monitor" "Not in stop mode,In stop mode" bitfld.long 0x00 0. " STOPEN ,Stop mode enable" "Disabled,Enabled" endif group.long 0x10++0x07 line.long 0x00 "CRIMA,Interrupt Mask Control Register" bitfld.long 0x00 0. " RDYINTM ,Mask signal of PLLRDY interrupt" "Not masked,Masked" line.long 0x04 "CRPIC,Interrupt Clear Register" bitfld.long 0x04 0. " PLLRDYINT ,PLLRDY interrupt clear" "Not asserted,Asserted" group.long 0x20++0x13 line.long 0x00 "CRRSC,CRG Reset Control Register" sif (cpu()=="MB86R24") bitfld.long 0x00 16.--19. " SRSTMODE ,SRST reset pulse width" "8 x TCCLK,48 x TCCLK,64 x TCCLK,96 x TCCLK,128 x TCCLK,192 x TCCLK,256 x TCCLK,384 x TCCLK,512 x TCCLK,768 x TCCLK,1024 x TCCLK,1536 x TCCLK,2048 x TCCLK,3072 x TCCLK,4096 x TCCLK,6144 x TCCLK" else bitfld.long 0x00 16.--19. " SRSTMODE ,SRST reset pulse width" "8 x TCCLK,12 x TCCLK,16 x TCCLK,24 x TCCLK,32 x TCCLK,48 x TCCLK,64 x TCCLK,96 x TCCLK,128 x TCCLK,192 x TCCLK,256 x TCCLK,384 x TCCLK,512 x TCCLK,768 x TCCLK,1024 x TCCLK,1536 x TCCLK" endif bitfld.long 0x00 9. " WDRSTM ,Watchdog reset mode" "Not initialized,Initialized" textline " " bitfld.long 0x00 8. " SWRSTM ,Software reset mode" "No reset mode,Reset mode" textline " " bitfld.long 0x00 0.--3. " ARSTMODE ,Software reset pulse width" "8 x TCCLK,12 x TCCLK,16 x TCCLK,24 x TCCLK,32 x TCCLK,48 x TCCLK,64 x TCCLK,96 x TCCLK,128 x TCCLK,192 x TCCLK,256 x TCCLK,384 x TCCLK,512 x TCCLK,768 x TCCLK,1024 x TCCLK,1536 x TCCLK" line.long 0x04 "CRSWR,Software Reset Request Register" bitfld.long 0x04 0. " SWRSTREQ ,Software reset request" "Not occurred,Occurred" line.long 0x08 "CRRRS,Register Controlled Reset Request Register" sif (cpu()=="MB86R12") bitfld.long 0x08 31. " RRSTREQ_[31] ,USART/CAN Register*7/UART Register*7/CRG_P Register*7 reset request" "Requested,Not requested" bitfld.long 0x08 30. " [30] ,CAN/USART/CRG_P Register*6 reset request" "Requested,Not requested" bitfld.long 0x08 29. " [29] ,I2C reset request" "Requested,Not requested" bitfld.long 0x08 27. " [27] ,ADC/PWM /EBC Register*5/Display0, Display1 Register*5/Capture Register*5/WriteBack Register*5 reset request" "Requested,Not requested" bitfld.long 0x08 25. " [25] ,AHB0 Bridge reset request" "Requested,Not requested" textline " " bitfld.long 0x08 24. " [24] ,GPIO/EXIRC reset request" "Requested,Not requested" bitfld.long 0x08 23. " [23] ,TIMER/WDT_A reset request" "Requested,Not requested" bitfld.long 0x08 22. " [22] ,ADC/PWM reset request" "Requested,Not requested" bitfld.long 0x08 21. " [21] ,APIX reset request" "Requested,Not requested" bitfld.long 0x08 20. " [20] ,AHB2 Bus *2/Display2 register/CmdSeq register/PixelEngine register/DDRC register reset request" "Requested,Not requested" textline " " bitfld.long 0x08 19. " [19] ,HS_SPI reset request" "Requested,Not requested" bitfld.long 0x08 18. " [18] ,SIG reset request" "Requested,Not requested" bitfld.long 0x08 17. " [17] ,TCON reset request" "Requested,Not requested" bitfld.long 0x08 16. " [16] ,IDE66 reset request" "Requested,Not requested" bitfld.long 0x08 15. " [15] ,WDT_B reset request" "Requested,Not requested" textline " " bitfld.long 0x08 14. " [14] ,Ether reset request" "Requested,Not requested" bitfld.long 0x08 13. " [13] ,I2S reset request" "Requested,Not requested" bitfld.long 0x08 12. " [12] ,SFI reset request" "Requested,Not requested" bitfld.long 0x08 11. " [11] ,RLD reset request" "Requested,Not requested" bitfld.long 0x08 10. " [10] ,HDMAC reset request" "Requested,Not requested" textline " " bitfld.long 0x08 9. " [9] ,HSRAM1 reset request" "Requested,Not requested" bitfld.long 0x08 8. " [8] ,AHB1 Bus *1 reset request" "Requested,Not requested" bitfld.long 0x08 7. " [7] ,DDR2/3 Controller reset request" "Requested,Not requested" bitfld.long 0x08 6. " [6] ,3D Graphics Engine/PixelEngine reset request" "Requested,Not requested" bitfld.long 0x08 5. " [5] ,Display/Capture/Writeback reset request" "Requested,Not requested" textline " " bitfld.long 0x08 4. " [4] ,IrDA reset request" "Requested,Not requested" bitfld.long 0x08 2. " [2] ,SDIO Interface reset request" "Requested,Not requested" bitfld.long 0x08 1. " [1] ,MediaLB reset request" "Requested,Not requested" bitfld.long 0x08 0. " [0] ,CRG_P reset request" "Requested,Not requested" elif (cpu()=="MB86R24") bitfld.long 0x08 31. " RRSTREQ_[31] ,USART reset request" "Requested,Not requested" bitfld.long 0x08 30. " [30] ,CAN/UART/CRG_P Register*6 reset request" "Requested,Not requested" bitfld.long 0x08 29. " [29] ,I2C reset request" "Requested,Not requested" bitfld.long 0x08 26. " [26] ,PWM Register *5/ADC Register *5/EBC Register *5 reset request" "Requested,Not requested" bitfld.long 0x08 25. " [25] ,AHB0 Bridge reset request" "Requested,Not requested" textline " " bitfld.long 0x08 24. " [24] ,GPIO/EXIRC reset request" "Requested,Not requested" bitfld.long 0x08 23. " [23] ,TIMER/WDT_A reset request" "Requested,Not requested" bitfld.long 0x08 22. " [22] ,PWM reset request" "Requested,Not requested" bitfld.long 0x08 21. " [21] ,ADC reset request" "Requested,Not requested" bitfld.long 0x08 20. " [20] ,AHB2 Bus *2/Iris_MDP Register *4/Command Sequencer Register *4/SGX Register *4/DDRC Register *4 reset request" "Requested,Not requested" textline " " bitfld.long 0x08 19. " [19] ,HS_SPI reset request" "Requested,Not requested" bitfld.long 0x08 18. " [18] ,SIG reset request" "Requested,Not requested" bitfld.long 0x08 17. " [17] ,TCON reset request" "Requested,Not requested" bitfld.long 0x08 15. " [15] ,WDT_B reset request" "Requested,Not requested" textline " " bitfld.long 0x08 14. " [14] ,Ethernet reset request" "Requested,Not requested" bitfld.long 0x08 13. " [13] ,I2S reset request" "Requested,Not requested" bitfld.long 0x08 12. " [12] ,SFI reset request" "Requested,Not requested" bitfld.long 0x08 11. " [11] ,DDR Controller 1 reset request" "Requested,Not requested" bitfld.long 0x08 10. " [10] ,HDMAC reset request" "Requested,Not requested" textline " " bitfld.long 0x08 8. " [8] ,AHB1 Bus *1 reset request" "Requested,Not requested" bitfld.long 0x08 7. " [7] ,DDR Controller 0 reset request" "Requested,Not requested" bitfld.long 0x08 6. " [6] ,Iris-MDP reset request" "Requested,Not requested" bitfld.long 0x08 5. " [5] ,Display/Capture/Writeback reset request" "Requested,Not requested" textline " " bitfld.long 0x08 4. " [4] ,SGX reset request" "Requested,Not requested" bitfld.long 0x08 3. " [3] ,USB reset request" "Requested,Not requested" bitfld.long 0x08 2. " [2] ,SDIO Interface reset request" "Requested,Not requested" bitfld.long 0x08 1. " [1] ,MediaLB reset request" "Requested,Not requested" bitfld.long 0x08 0. " [0] ,CRG_P reset request" "Requested,Not requested" else bitfld.long 0x08 31. " RRSTREQ_[31] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 30. " [30] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 29. " [29] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 28. " [28] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 27. " [27] ,Register-controlled reset request" "Requested,Not requested" textline " " bitfld.long 0x08 26. " [26] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 25. " [25] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 24. " [24] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 23. " [23] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 22. " [22] ,Register-controlled reset request" "Requested,Not requested" textline " " bitfld.long 0x08 21. " [21] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 20. " [20] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 19. " [19] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 18. " [18] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 17. " [17] ,Register-controlled reset request" "Requested,Not requested" textline " " bitfld.long 0x08 16. " [16] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 15. " [15] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 14. " [14] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 13. " [13] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 12. " [12] ,Register-controlled reset request" "Requested,Not requested" textline " " bitfld.long 0x08 11. " [11] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 10. " [10] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 9. " [9] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 8. " [8] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 7. " [7] ,Register-controlled reset request" "Requested,Not requested" textline " " bitfld.long 0x08 6. " [6] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 5. " [5] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 4. " [4] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 3. " [3] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 2. " [2] ,Register-controlled reset request" "Requested,Not requested" textline " " bitfld.long 0x08 1. " [1] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 0. " [0] ,Register-controlled reset request" "Requested,Not requested" endif textline " " line.long 0x0C "CRRSM,Reset And Monitor Register" bitfld.long 0x0C 3. " PORESET ,PORESETn monitor" "Not asserted,Asserted" bitfld.long 0x0C 2. " SRST ,SRST reset monitor" "Not asserted,Asserted" bitfld.long 0x0C 1. " SWRST ,Software reset monitor" "Not asserted,Asserted" bitfld.long 0x0C 0. " WDRST ,Watchdog reset monitor" "Not asserted,Asserted" line.long 0x10 "CRCDC,Clock Divider Control Register" bitfld.long 0x10 0. " DCHREQ ,Clock divider mode update request" "Not updated,Updated" textline " " sif (cpu()=="MB86R24") rgroup.long 0x34++0x03 line.long 0x00 "CRMNT,RRESETn Monitor Register" bitfld.long 0x00 31. " RRSTREQ_[31] ,USART reset request" "Requested,Not requested" bitfld.long 0x00 30. " [30] ,CAN/UART/CRG_P Register*6 reset request" "Requested,Not requested" bitfld.long 0x00 29. " [29] ,I2C reset request" "Requested,Not requested" bitfld.long 0x00 26. " [26] ,PWM Register *5/ADC Register *5/EBC Register *5 reset request" "Requested,Not requested" bitfld.long 0x00 25. " [25] ,AHB0 Bridge reset request" "Requested,Not requested" textline " " bitfld.long 0x00 24. " [24] ,GPIO/EXIRC reset request" "Requested,Not requested" bitfld.long 0x00 23. " [23] ,TIMER/WDT_A reset request" "Requested,Not requested" bitfld.long 0x00 22. " [22] ,PWM reset request" "Requested,Not requested" bitfld.long 0x00 21. " [21] ,ADC reset request" "Requested,Not requested" bitfld.long 0x00 20. " [20] ,AHB2 Bus *2/Iris_MDP Register *4/Command Sequencer Register *4/SGX Register *4/DDRC Register *4 reset request" "Requested,Not requested" textline " " bitfld.long 0x00 19. " [19] ,HS_SPI reset request" "Requested,Not requested" bitfld.long 0x00 18. " [18] ,SIG reset request" "Requested,Not requested" bitfld.long 0x00 17. " [17] ,TCON reset request" "Requested,Not requested" bitfld.long 0x00 15. " [15] ,WDT_B reset request" "Requested,Not requested" textline " " bitfld.long 0x00 14. " [14] ,Ethernet reset request" "Requested,Not requested" bitfld.long 0x00 13. " [13] ,I2S reset request" "Requested,Not requested" bitfld.long 0x00 12. " [12] ,SFI reset request" "Requested,Not requested" bitfld.long 0x00 11. " [11] ,DDR Controller 1 reset request" "Requested,Not requested" bitfld.long 0x00 10. " [10] ,HDMAC reset request" "Requested,Not requested" textline " " bitfld.long 0x00 8. " [8] ,AHB1 Bus *1 reset request" "Requested,Not requested" bitfld.long 0x00 7. " [7] ,DDR Controller 0 reset request" "Requested,Not requested" bitfld.long 0x00 6. " [6] ,Iris-MDP reset request" "Requested,Not requested" bitfld.long 0x00 5. " [5] ,Display/Capture/Writeback reset request" "Requested,Not requested" textline " " bitfld.long 0x00 4. " [4] ,SGX reset request" "Requested,Not requested" bitfld.long 0x00 3. " [3] ,USB reset request" "Requested,Not requested" bitfld.long 0x00 2. " [2] ,SDIO Interface reset request" "Requested,Not requested" bitfld.long 0x00 1. " [1] ,MediaLB reset request" "Requested,Not requested" bitfld.long 0x00 0. " [0] ,CRG_P reset request" "Requested,Not requested" endif sif (cpu()=="MB86R24") group.long 0x100++0x07 line.long 0x00 "CRDM0,Clock Divider Mode Register Of CLK0" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE0 ,CLK0 domain divider mode" line.long 0x04 "CRLP0,Low Power Control Register Of CLK0" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x110++0x07 line.long 0x00 "CRDM1,Clock Divider Mode Register Of CLK1" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE1 ,CLK1 domain divider mode" line.long 0x04 "CRLP1,Low Power Control Register Of CLK1" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x120++0x07 line.long 0x00 "CRDM2,Clock Divider Mode Register Of CLK2" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE2 ,CLK2 domain divider mode" line.long 0x04 "CRLP2,Low Power Control Register Of CLK2" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x130++0x07 line.long 0x00 "CRDM3,Clock Divider Mode Register Of CLK3" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE3 ,CLK3 domain divider mode" line.long 0x04 "CRLP3,Low Power Control Register Of CLK3" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x140++0x07 line.long 0x00 "CRDM4,Clock Divider Mode Register Of CLK4" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE4 ,CLK4 domain divider mode" line.long 0x04 "CRLP4,Low Power Control Register Of CLK4" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x150++0x07 line.long 0x00 "CRDM5,Clock Divider Mode Register Of CLK5" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE5 ,CLK5 domain divider mode" line.long 0x04 "CRLP5,Low Power Control Register Of CLK5" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x160++0x07 line.long 0x00 "CRDM6,Clock Divider Mode Register Of CLK6" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE6 ,CLK6 domain divider mode" line.long 0x04 "CRLP6,Low Power Control Register Of CLK6" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x170++0x07 line.long 0x00 "CRDM7,Clock Divider Mode Register Of CLK7" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE7 ,CLK7 domain divider mode" line.long 0x04 "CRLP7,Low Power Control Register Of CLK7" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " else group.long 0x100++0x07 line.long 0x00 "CRDM0,Clock Divider Mode Register Of CLK0" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE0 ,CLK0 domain divider mode" line.long 0x04 "CRLP0,Low Power Control Register Of CLK0" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x110++0x07 line.long 0x00 "CRDM1,Clock Divider Mode Register Of CLK1" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE1 ,CLK1 domain divider mode" line.long 0x04 "CRLP1,Low Power Control Register Of CLK1" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x120++0x07 line.long 0x00 "CRDM2,Clock Divider Mode Register Of CLK2" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE2 ,CLK2 domain divider mode" line.long 0x04 "CRLP2,Low Power Control Register Of CLK2" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x130++0x07 line.long 0x00 "CRDM3,Clock Divider Mode Register Of CLK3" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE3 ,CLK3 domain divider mode" line.long 0x04 "CRLP3,Low Power Control Register Of CLK3" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x140++0x07 line.long 0x00 "CRDM4,Clock Divider Mode Register Of CLK4" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE4 ,CLK4 domain divider mode" line.long 0x04 "CRLP4,Low Power Control Register Of CLK4" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x150++0x07 line.long 0x00 "CRDM5,Clock Divider Mode Register Of CLK5" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE5 ,CLK5 domain divider mode" line.long 0x04 "CRLP5,Low Power Control Register Of CLK5" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x160++0x07 line.long 0x00 "CRDM6,Clock Divider Mode Register Of CLK6" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE6 ,CLK6 domain divider mode" line.long 0x04 "CRLP6,Low Power Control Register Of CLK6" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x170++0x07 line.long 0x00 "CRDM7,Clock Divider Mode Register Of CLK7" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE7 ,CLK7 domain divider mode" line.long 0x04 "CRLP7,Low Power Control Register Of CLK7" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x180++0x07 line.long 0x00 "CRDM8,Clock Divider Mode Register Of CLK8" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE8 ,CLK8 domain divider mode" line.long 0x04 "CRLP8,Low Power Control Register Of CLK8" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x190++0x07 line.long 0x00 "CRDM9,Clock Divider Mode Register Of CLK9" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE9 ,CLK9 domain divider mode" line.long 0x04 "CRLP9,Low Power Control Register Of CLK9" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x1A0++0x07 line.long 0x00 "CRDMA,Clock Divider Mode Register Of CLKA" hexmask.long.byte 0x00 0.--7. 1. " DIVMODEA ,CLKA domain divider mode" line.long 0x04 "CRLPA,Low Power Control Register Of CLKA" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x1B0++0x07 line.long 0x00 "CRDMB,Clock Divider Mode Register Of CLKB" hexmask.long.byte 0x00 0.--7. 1. " DIVMODEB ,CLKB domain divider mode" line.long 0x04 "CRLPB,Low Power Control Register Of CLKB" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x1C0++0x07 line.long 0x00 "CRDMC,Clock Divider Mode Register Of CLKC" hexmask.long.byte 0x00 0.--7. 1. " DIVMODEC ,CLKC domain divider mode" line.long 0x04 "CRLPC,Low Power Control Register Of CLKC" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x1D0++0x07 line.long 0x00 "CRDMD,Clock Divider Mode Register Of CLKD" hexmask.long.byte 0x00 0.--7. 1. " DIVMODED ,CLKD domain divider mode" line.long 0x04 "CRLPD,Low Power Control Register Of CLKD" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x1E0++0x07 line.long 0x00 "CRDME,Clock Divider Mode Register Of CLKE" hexmask.long.byte 0x00 0.--7. 1. " DIVMODEE ,CLKE domain divider mode" line.long 0x04 "CRLPE,Low Power Control Register Of CLKE" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x1F0++0x07 line.long 0x00 "CRDMF,Clock Divider Mode Register Of CLKF" hexmask.long.byte 0x00 0.--7. 1. " DIVMODEF ,CLKF domain divider mode" line.long 0x04 "CRLPF,Low Power Control Register Of CLKF" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " endif width 0x0B tree.end tree "CRG-S" base ad:0x3B500000 width 8. if (((per.l(ad:0x3B500000))&0x7F)==0x00) group.long 0x00++0x03 line.long 0x00 "CRPLC,PLL Control Register" rbitfld.long 0x00 24. " PLLBYPASS ,PLL bypass mode" "Not bypassed,Bypassed" bitfld.long 0x00 16.--19. " LUWMODE ,PLL lock-up wait time" "64 * TREFCLK,128*TREFCLK,512*TREFCLK,768*TREFCLK,1024*TREFCLK,1536*TREFCLK,2048*TREFCLK,3072*TREFCLK,4096*TREFCLK,6144*TREFCLK,8192*TREFCLK,12288*TREFCLK,16384*TREFCLK,24576*TREFCLK,32768*TREFCLK,49152*TREFCLK" bitfld.long 0x00 8.--11. " PSMODE ,Sets the dividing ratio of the PLL clock frequency" "1,1/2,?..." textline " " bitfld.long 0x00 0.--5. " FBMODE ,Stops operation of the PLL clock" "Stopped,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,Activated" else group.long 0x00++0x03 line.long 0x00 "CRPLC,PLL Control Register" bitfld.long 0x00 24. " PLLBYPASS ,PLL bypass mode" "Not bypassed,Bypassed" bitfld.long 0x00 16.--19. " LUWMODE ,PLL lock-up wait time" "64 * TREFCLK,128*TREFCLK,512*TREFCLK,768*TREFCLK,1024*TREFCLK,1536*TREFCLK,2048*TREFCLK,3072*TREFCLK,4096*TREFCLK,6144*TREFCLK,8192*TREFCLK,12288*TREFCLK,16384*TREFCLK,24576*TREFCLK,32768*TREFCLK,49152*TREFCLK" bitfld.long 0x00 8.--11. " PSMODE ,Sets the dividing ratio of the PLL clock frequency" "1,1/2,?..." textline " " bitfld.long 0x00 0.--5. " FBMODE ,Stops operation of the PLL clock" "Stopped,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,Activated" endif rgroup.long 0x04++0x03 line.long 0x00 "CRRDY,PLL Ready Monitor Register" bitfld.long 0x00 4. " PSRMNT ,PSMODE monitor" "Not used,Used" bitfld.long 0x00 0. " PLLRDY ,PLLREADY monitor" "Not ready,Ready" if (((per.l(ad:0x3B500000))&0x7F)==0x00) group.long 0x08++0x03 line.long 0x00 "CRSTP,Stop Control Register" bitfld.long 0x00 1. " STOPMNT ,Stop mode monitor" "Not in stop mode,In stop mode" bitfld.long 0x00 0. " STOPEN ,Stop mode enable" "Disabled,Enabled" else group.long 0x08++0x03 line.long 0x00 "CRSTP,Stop Control Register" rbitfld.long 0x00 1. " STOPMNT ,Stop mode monitor" "Not in stop mode,In stop mode" bitfld.long 0x00 0. " STOPEN ,Stop mode enable" "Disabled,Enabled" endif group.long 0x10++0x07 line.long 0x00 "CRIMA,Interrupt Mask Control Register" bitfld.long 0x00 0. " RDYINTM ,Mask signal of PLLRDY interrupt" "Not masked,Masked" line.long 0x04 "CRPIC,Interrupt Clear Register" bitfld.long 0x04 0. " PLLRDYINT ,PLLRDY interrupt clear" "Not asserted,Asserted" group.long 0x20++0x13 line.long 0x00 "CRRSC,CRG Reset Control Register" sif (cpu()=="MB86R24") bitfld.long 0x00 16.--19. " SRSTMODE ,SRST reset pulse width" "8 x TCCLK,48 x TCCLK,64 x TCCLK,96 x TCCLK,128 x TCCLK,192 x TCCLK,256 x TCCLK,384 x TCCLK,512 x TCCLK,768 x TCCLK,1024 x TCCLK,1536 x TCCLK,2048 x TCCLK,3072 x TCCLK,4096 x TCCLK,6144 x TCCLK" else bitfld.long 0x00 16.--19. " SRSTMODE ,SRST reset pulse width" "8 x TCCLK,12 x TCCLK,16 x TCCLK,24 x TCCLK,32 x TCCLK,48 x TCCLK,64 x TCCLK,96 x TCCLK,128 x TCCLK,192 x TCCLK,256 x TCCLK,384 x TCCLK,512 x TCCLK,768 x TCCLK,1024 x TCCLK,1536 x TCCLK" endif bitfld.long 0x00 9. " WDRSTM ,Watchdog reset mode" "Not initialized,Initialized" textline " " bitfld.long 0x00 8. " SWRSTM ,Software reset mode" "No reset mode,Reset mode" textline " " bitfld.long 0x00 0.--3. " ARSTMODE ,Software reset pulse width" "8 x TCCLK,12 x TCCLK,16 x TCCLK,24 x TCCLK,32 x TCCLK,48 x TCCLK,64 x TCCLK,96 x TCCLK,128 x TCCLK,192 x TCCLK,256 x TCCLK,384 x TCCLK,512 x TCCLK,768 x TCCLK,1024 x TCCLK,1536 x TCCLK" line.long 0x04 "CRSWR,Software Reset Request Register" bitfld.long 0x04 0. " SWRSTREQ ,Software reset request" "Not occurred,Occurred" line.long 0x08 "CRRRS,Register Controlled Reset Request Register" sif (cpu()=="MB86R12") bitfld.long 0x08 31. " RRSTREQ_[31] ,USART/CAN Register*7/UART Register*7/CRG_P Register*7 reset request" "Requested,Not requested" bitfld.long 0x08 30. " [30] ,CAN/USART/CRG_P Register*6 reset request" "Requested,Not requested" bitfld.long 0x08 29. " [29] ,I2C reset request" "Requested,Not requested" bitfld.long 0x08 27. " [27] ,ADC/PWM /EBC Register*5/Display0, Display1 Register*5/Capture Register*5/WriteBack Register*5 reset request" "Requested,Not requested" bitfld.long 0x08 25. " [25] ,AHB0 Bridge reset request" "Requested,Not requested" textline " " bitfld.long 0x08 24. " [24] ,GPIO/EXIRC reset request" "Requested,Not requested" bitfld.long 0x08 23. " [23] ,TIMER/WDT_A reset request" "Requested,Not requested" bitfld.long 0x08 22. " [22] ,ADC/PWM reset request" "Requested,Not requested" bitfld.long 0x08 21. " [21] ,APIX reset request" "Requested,Not requested" bitfld.long 0x08 20. " [20] ,AHB2 Bus *2/Display2 register/CmdSeq register/PixelEngine register/DDRC register reset request" "Requested,Not requested" textline " " bitfld.long 0x08 19. " [19] ,HS_SPI reset request" "Requested,Not requested" bitfld.long 0x08 18. " [18] ,SIG reset request" "Requested,Not requested" bitfld.long 0x08 17. " [17] ,TCON reset request" "Requested,Not requested" bitfld.long 0x08 16. " [16] ,IDE66 reset request" "Requested,Not requested" bitfld.long 0x08 15. " [15] ,WDT_B reset request" "Requested,Not requested" textline " " bitfld.long 0x08 14. " [14] ,Ether reset request" "Requested,Not requested" bitfld.long 0x08 13. " [13] ,I2S reset request" "Requested,Not requested" bitfld.long 0x08 12. " [12] ,SFI reset request" "Requested,Not requested" bitfld.long 0x08 11. " [11] ,RLD reset request" "Requested,Not requested" bitfld.long 0x08 10. " [10] ,HDMAC reset request" "Requested,Not requested" textline " " bitfld.long 0x08 9. " [9] ,HSRAM1 reset request" "Requested,Not requested" bitfld.long 0x08 8. " [8] ,AHB1 Bus *1 reset request" "Requested,Not requested" bitfld.long 0x08 7. " [7] ,DDR2/3 Controller reset request" "Requested,Not requested" bitfld.long 0x08 6. " [6] ,3D Graphics Engine/PixelEngine reset request" "Requested,Not requested" bitfld.long 0x08 5. " [5] ,Display/Capture/Writeback reset request" "Requested,Not requested" textline " " bitfld.long 0x08 4. " [4] ,IrDA reset request" "Requested,Not requested" bitfld.long 0x08 2. " [2] ,SDIO Interface reset request" "Requested,Not requested" bitfld.long 0x08 1. " [1] ,MediaLB reset request" "Requested,Not requested" bitfld.long 0x08 0. " [0] ,CRG_P reset request" "Requested,Not requested" elif (cpu()=="MB86R24") bitfld.long 0x08 31. " RRSTREQ_[31] ,USART reset request" "Requested,Not requested" bitfld.long 0x08 30. " [30] ,CAN/UART/CRG_P Register*6 reset request" "Requested,Not requested" bitfld.long 0x08 29. " [29] ,I2C reset request" "Requested,Not requested" bitfld.long 0x08 26. " [26] ,PWM Register *5/ADC Register *5/EBC Register *5 reset request" "Requested,Not requested" bitfld.long 0x08 25. " [25] ,AHB0 Bridge reset request" "Requested,Not requested" textline " " bitfld.long 0x08 24. " [24] ,GPIO/EXIRC reset request" "Requested,Not requested" bitfld.long 0x08 23. " [23] ,TIMER/WDT_A reset request" "Requested,Not requested" bitfld.long 0x08 22. " [22] ,PWM reset request" "Requested,Not requested" bitfld.long 0x08 21. " [21] ,ADC reset request" "Requested,Not requested" bitfld.long 0x08 20. " [20] ,AHB2 Bus *2/Iris_MDP Register *4/Command Sequencer Register *4/SGX Register *4/DDRC Register *4 reset request" "Requested,Not requested" textline " " bitfld.long 0x08 19. " [19] ,HS_SPI reset request" "Requested,Not requested" bitfld.long 0x08 18. " [18] ,SIG reset request" "Requested,Not requested" bitfld.long 0x08 17. " [17] ,TCON reset request" "Requested,Not requested" bitfld.long 0x08 15. " [15] ,WDT_B reset request" "Requested,Not requested" textline " " bitfld.long 0x08 14. " [14] ,Ethernet reset request" "Requested,Not requested" bitfld.long 0x08 13. " [13] ,I2S reset request" "Requested,Not requested" bitfld.long 0x08 12. " [12] ,SFI reset request" "Requested,Not requested" bitfld.long 0x08 11. " [11] ,DDR Controller 1 reset request" "Requested,Not requested" bitfld.long 0x08 10. " [10] ,HDMAC reset request" "Requested,Not requested" textline " " bitfld.long 0x08 8. " [8] ,AHB1 Bus *1 reset request" "Requested,Not requested" bitfld.long 0x08 7. " [7] ,DDR Controller 0 reset request" "Requested,Not requested" bitfld.long 0x08 6. " [6] ,Iris-MDP reset request" "Requested,Not requested" bitfld.long 0x08 5. " [5] ,Display/Capture/Writeback reset request" "Requested,Not requested" textline " " bitfld.long 0x08 4. " [4] ,SGX reset request" "Requested,Not requested" bitfld.long 0x08 3. " [3] ,USB reset request" "Requested,Not requested" bitfld.long 0x08 2. " [2] ,SDIO Interface reset request" "Requested,Not requested" bitfld.long 0x08 1. " [1] ,MediaLB reset request" "Requested,Not requested" bitfld.long 0x08 0. " [0] ,CRG_P reset request" "Requested,Not requested" else bitfld.long 0x08 31. " RRSTREQ_[31] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 30. " [30] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 29. " [29] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 28. " [28] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 27. " [27] ,Register-controlled reset request" "Requested,Not requested" textline " " bitfld.long 0x08 26. " [26] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 25. " [25] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 24. " [24] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 23. " [23] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 22. " [22] ,Register-controlled reset request" "Requested,Not requested" textline " " bitfld.long 0x08 21. " [21] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 20. " [20] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 19. " [19] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 18. " [18] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 17. " [17] ,Register-controlled reset request" "Requested,Not requested" textline " " bitfld.long 0x08 16. " [16] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 15. " [15] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 14. " [14] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 13. " [13] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 12. " [12] ,Register-controlled reset request" "Requested,Not requested" textline " " bitfld.long 0x08 11. " [11] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 10. " [10] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 9. " [9] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 8. " [8] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 7. " [7] ,Register-controlled reset request" "Requested,Not requested" textline " " bitfld.long 0x08 6. " [6] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 5. " [5] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 4. " [4] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 3. " [3] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 2. " [2] ,Register-controlled reset request" "Requested,Not requested" textline " " bitfld.long 0x08 1. " [1] ,Register-controlled reset request" "Requested,Not requested" bitfld.long 0x08 0. " [0] ,Register-controlled reset request" "Requested,Not requested" endif textline " " line.long 0x0C "CRRSM,Reset And Monitor Register" bitfld.long 0x0C 3. " PORESET ,PORESETn monitor" "Not asserted,Asserted" bitfld.long 0x0C 2. " SRST ,SRST reset monitor" "Not asserted,Asserted" bitfld.long 0x0C 1. " SWRST ,Software reset monitor" "Not asserted,Asserted" bitfld.long 0x0C 0. " WDRST ,Watchdog reset monitor" "Not asserted,Asserted" line.long 0x10 "CRCDC,Clock Divider Control Register" bitfld.long 0x10 0. " DCHREQ ,Clock divider mode update request" "Not updated,Updated" textline " " sif (cpu()=="MB86R24") rgroup.long 0x34++0x03 line.long 0x00 "CRMNT,RRESETn Monitor Register" bitfld.long 0x00 31. " RRSTREQ_[31] ,USART reset request" "Requested,Not requested" bitfld.long 0x00 30. " [30] ,CAN/UART/CRG_P Register*6 reset request" "Requested,Not requested" bitfld.long 0x00 29. " [29] ,I2C reset request" "Requested,Not requested" bitfld.long 0x00 26. " [26] ,PWM Register *5/ADC Register *5/EBC Register *5 reset request" "Requested,Not requested" bitfld.long 0x00 25. " [25] ,AHB0 Bridge reset request" "Requested,Not requested" textline " " bitfld.long 0x00 24. " [24] ,GPIO/EXIRC reset request" "Requested,Not requested" bitfld.long 0x00 23. " [23] ,TIMER/WDT_A reset request" "Requested,Not requested" bitfld.long 0x00 22. " [22] ,PWM reset request" "Requested,Not requested" bitfld.long 0x00 21. " [21] ,ADC reset request" "Requested,Not requested" bitfld.long 0x00 20. " [20] ,AHB2 Bus *2/Iris_MDP Register *4/Command Sequencer Register *4/SGX Register *4/DDRC Register *4 reset request" "Requested,Not requested" textline " " bitfld.long 0x00 19. " [19] ,HS_SPI reset request" "Requested,Not requested" bitfld.long 0x00 18. " [18] ,SIG reset request" "Requested,Not requested" bitfld.long 0x00 17. " [17] ,TCON reset request" "Requested,Not requested" bitfld.long 0x00 15. " [15] ,WDT_B reset request" "Requested,Not requested" textline " " bitfld.long 0x00 14. " [14] ,Ethernet reset request" "Requested,Not requested" bitfld.long 0x00 13. " [13] ,I2S reset request" "Requested,Not requested" bitfld.long 0x00 12. " [12] ,SFI reset request" "Requested,Not requested" bitfld.long 0x00 11. " [11] ,DDR Controller 1 reset request" "Requested,Not requested" bitfld.long 0x00 10. " [10] ,HDMAC reset request" "Requested,Not requested" textline " " bitfld.long 0x00 8. " [8] ,AHB1 Bus *1 reset request" "Requested,Not requested" bitfld.long 0x00 7. " [7] ,DDR Controller 0 reset request" "Requested,Not requested" bitfld.long 0x00 6. " [6] ,Iris-MDP reset request" "Requested,Not requested" bitfld.long 0x00 5. " [5] ,Display/Capture/Writeback reset request" "Requested,Not requested" textline " " bitfld.long 0x00 4. " [4] ,SGX reset request" "Requested,Not requested" bitfld.long 0x00 3. " [3] ,USB reset request" "Requested,Not requested" bitfld.long 0x00 2. " [2] ,SDIO Interface reset request" "Requested,Not requested" bitfld.long 0x00 1. " [1] ,MediaLB reset request" "Requested,Not requested" bitfld.long 0x00 0. " [0] ,CRG_P reset request" "Requested,Not requested" endif sif (cpu()=="MB86R24") group.long 0x100++0x07 line.long 0x00 "CRDM0,Clock Divider Mode Register Of CLK0" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE0 ,CLK0 domain divider mode" line.long 0x04 "CRLP0,Low Power Control Register Of CLK0" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x110++0x07 line.long 0x00 "CRDM1,Clock Divider Mode Register Of CLK1" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE1 ,CLK1 domain divider mode" line.long 0x04 "CRLP1,Low Power Control Register Of CLK1" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x120++0x07 line.long 0x00 "CRDM2,Clock Divider Mode Register Of CLK2" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE2 ,CLK2 domain divider mode" line.long 0x04 "CRLP2,Low Power Control Register Of CLK2" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x130++0x07 line.long 0x00 "CRDM3,Clock Divider Mode Register Of CLK3" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE3 ,CLK3 domain divider mode" line.long 0x04 "CRLP3,Low Power Control Register Of CLK3" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x140++0x07 line.long 0x00 "CRDM4,Clock Divider Mode Register Of CLK4" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE4 ,CLK4 domain divider mode" line.long 0x04 "CRLP4,Low Power Control Register Of CLK4" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x150++0x07 line.long 0x00 "CRDM5,Clock Divider Mode Register Of CLK5" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE5 ,CLK5 domain divider mode" line.long 0x04 "CRLP5,Low Power Control Register Of CLK5" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x160++0x07 line.long 0x00 "CRDM6,Clock Divider Mode Register Of CLK6" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE6 ,CLK6 domain divider mode" line.long 0x04 "CRLP6,Low Power Control Register Of CLK6" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x170++0x07 line.long 0x00 "CRDM7,Clock Divider Mode Register Of CLK7" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE7 ,CLK7 domain divider mode" line.long 0x04 "CRLP7,Low Power Control Register Of CLK7" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " else group.long 0x100++0x07 line.long 0x00 "CRDM0,Clock Divider Mode Register Of CLK0" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE0 ,CLK0 domain divider mode" line.long 0x04 "CRLP0,Low Power Control Register Of CLK0" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x110++0x07 line.long 0x00 "CRDM1,Clock Divider Mode Register Of CLK1" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE1 ,CLK1 domain divider mode" line.long 0x04 "CRLP1,Low Power Control Register Of CLK1" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x120++0x07 line.long 0x00 "CRDM2,Clock Divider Mode Register Of CLK2" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE2 ,CLK2 domain divider mode" line.long 0x04 "CRLP2,Low Power Control Register Of CLK2" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x130++0x07 line.long 0x00 "CRDM3,Clock Divider Mode Register Of CLK3" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE3 ,CLK3 domain divider mode" line.long 0x04 "CRLP3,Low Power Control Register Of CLK3" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x140++0x07 line.long 0x00 "CRDM4,Clock Divider Mode Register Of CLK4" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE4 ,CLK4 domain divider mode" line.long 0x04 "CRLP4,Low Power Control Register Of CLK4" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x150++0x07 line.long 0x00 "CRDM5,Clock Divider Mode Register Of CLK5" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE5 ,CLK5 domain divider mode" line.long 0x04 "CRLP5,Low Power Control Register Of CLK5" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x160++0x07 line.long 0x00 "CRDM6,Clock Divider Mode Register Of CLK6" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE6 ,CLK6 domain divider mode" line.long 0x04 "CRLP6,Low Power Control Register Of CLK6" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x170++0x07 line.long 0x00 "CRDM7,Clock Divider Mode Register Of CLK7" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE7 ,CLK7 domain divider mode" line.long 0x04 "CRLP7,Low Power Control Register Of CLK7" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x180++0x07 line.long 0x00 "CRDM8,Clock Divider Mode Register Of CLK8" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE8 ,CLK8 domain divider mode" line.long 0x04 "CRLP8,Low Power Control Register Of CLK8" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x190++0x07 line.long 0x00 "CRDM9,Clock Divider Mode Register Of CLK9" hexmask.long.byte 0x00 0.--7. 1. " DIVMODE9 ,CLK9 domain divider mode" line.long 0x04 "CRLP9,Low Power Control Register Of CLK9" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x1A0++0x07 line.long 0x00 "CRDMA,Clock Divider Mode Register Of CLKA" hexmask.long.byte 0x00 0.--7. 1. " DIVMODEA ,CLKA domain divider mode" line.long 0x04 "CRLPA,Low Power Control Register Of CLKA" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x1B0++0x07 line.long 0x00 "CRDMB,Clock Divider Mode Register Of CLKB" hexmask.long.byte 0x00 0.--7. 1. " DIVMODEB ,CLKB domain divider mode" line.long 0x04 "CRLPB,Low Power Control Register Of CLKB" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x1C0++0x07 line.long 0x00 "CRDMC,Clock Divider Mode Register Of CLKC" hexmask.long.byte 0x00 0.--7. 1. " DIVMODEC ,CLKC domain divider mode" line.long 0x04 "CRLPC,Low Power Control Register Of CLKC" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x1D0++0x07 line.long 0x00 "CRDMD,Clock Divider Mode Register Of CLKD" hexmask.long.byte 0x00 0.--7. 1. " DIVMODED ,CLKD domain divider mode" line.long 0x04 "CRLPD,Low Power Control Register Of CLKD" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x1E0++0x07 line.long 0x00 "CRDME,Clock Divider Mode Register Of CLKE" hexmask.long.byte 0x00 0.--7. 1. " DIVMODEE ,CLKE domain divider mode" line.long 0x04 "CRLPE,Low Power Control Register Of CLKE" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " group.long 0x1F0++0x07 line.long 0x00 "CRDMF,Clock Divider Mode Register Of CLKF" hexmask.long.byte 0x00 0.--7. 1. " DIVMODEF ,CLKF domain divider mode" line.long 0x04 "CRLPF,Low Power Control Register Of CLKF" rbitfld.long 0x04 31. " CEN_[7] ,Low power state monitor 7" "Stopped,Not stopped" rbitfld.long 0x04 30. " [6] ,Low power state monitor 6" "Stopped,Not stopped" rbitfld.long 0x04 29. " [5] ,Low power state monitor 5" "Stopped,Not stopped" rbitfld.long 0x04 28. " [4] ,Low power state monitor 4" "Stopped,Not stopped" rbitfld.long 0x04 27. " [3] ,Low power state monitor 3" "Stopped,Not stopped" textline " " rbitfld.long 0x04 26. " [2] ,Low power state monitor 2" "Stopped,Not stopped" rbitfld.long 0x04 25. " [1] ,Low power state monitor 1" "Stopped,Not stopped" rbitfld.long 0x04 24. " [0] ,Low power state monitor 0" "Stopped,Not stopped" textline " " rbitfld.long 0x04 23. " CACTIVE_C_[7] ,Internal CACTIVE_C7 signal" "Not asserted,Asserted" rbitfld.long 0x04 22. " [6] ,Internal CACTIVE_C6 signal" "Not asserted,Asserted" rbitfld.long 0x04 21. " [5] ,Internal CACTIVE_C5 signal" "Not asserted,Asserted" rbitfld.long 0x04 20. " [4] ,Internal CACTIVE_C4 signal" "Not asserted,Asserted" rbitfld.long 0x04 19. " [3] ,Internal CACTIVE_C3 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 18. " [2] ,Internal CACTIVE_C2 signal" "Not asserted,Asserted" rbitfld.long 0x04 17. " [1] ,Internal CACTIVE_C1 signal" "Not asserted,Asserted" rbitfld.long 0x04 16. " [0] ,Internal CACTIVE_C0 signal" "Not asserted,Asserted" textline " " rbitfld.long 0x04 15. " LPOWERHS_[7] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 14. " [6] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 13. " [5] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 12. " [4] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 11. " [3] ,Low power handshake signal" "Acceptable,Ignored" textline " " rbitfld.long 0x04 10. " [2] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 9. " [1] ,Low power handshake signal" "Acceptable,Ignored" rbitfld.long 0x04 8. " [0] ,Low power handshake signal" "Acceptable,Ignored" textline " " bitfld.long 0x04 7. " CSYSREQ_R_[7] ,Clock gate 7" "Not active,Active" bitfld.long 0x04 6. " [6] ,Clock gate 6" "Not active,Active" bitfld.long 0x04 5. " [5] ,Clock gate 5" "Not active,Active" bitfld.long 0x04 4. " [4] ,Clock gate 4" "Not active,Active" bitfld.long 0x04 3. " [3] ,Clock gate 3" "Not active,Active" textline " " bitfld.long 0x04 2. " [2] ,Clock gate 2" "Not active,Active" bitfld.long 0x04 1. " [1] ,Clock gate 1" "Not active,Active" bitfld.long 0x04 0. " [0] ,Clock gate 0" "Not active,Active" textline " " endif width 0x0B tree.end tree.end tree "Boot Controller" base ad:0x3B200000 width 10. rgroup.long 0x00++0x03 line.long 0x00 "REMAPSTA,Remap Status Register" bitfld.long 0x00 0. " REMAPSTATUS ,Status of the remap register" "Before remapping,After remapping" wgroup.long 0x04++0x03 line.long 0x00 "REMAPSET,Remap Set Register" bitfld.long 0x00 0. " REMAPSET ,Set the remap register" "Not set,Set" sif (cpu()=="MB86R24") rgroup.long 0x0C++0x03 else rgroup.long 0x10++0x03 endif line.long 0x00 "VIHSTA,VINITHI Status Register" bitfld.long 0x00 0. " VIH_STATUS ,Current status of the VIHSTA register" "0,1" group.long 0x30++0x03 line.long 0x00 "GPREG0,General Purpose Register 0" group.long 0x34++0x03 line.long 0x00 "GPREG1,General Purpose Register 1" group.long 0x38++0x03 line.long 0x00 "GPREG2,General Purpose Register 2" group.long 0x3C++0x03 line.long 0x00 "GPREG3,General Purpose Register 3" group.long 0x50++0x13 line.long 0x00 "DSH0SEL,Default Slave AHB_0 Register" sif (cpu()=="MB86R12") bitfld.long 0x00 9. " Boot_ROM ,Switch a slave interface of the Boot ROM unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x00 5. " SDIO_2 ,Switch a slave interface of the SDIO 2 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x00 4. " SDIO_1 ,Switch a slave interface of the SDIO 1 unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x00 3. " SDIO_0 ,Switch a slave interface of the SDIO 0 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x00 1. " HSRAM_0 ,Switch a slave interface of the HSRAM 0 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x00 0. " MEDIA_LB ,Switch a slave interface of the Media LB unit and an error response circuit" "Slave interface,Error response circuit" elif (cpu()=="MB86R24") bitfld.long 0x00 9. " Boot_ROM ,Switch a slave interface of the Boot ROM unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x00 7. " US_HF_HOST ,Switch a slave interface of the USB HF host unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x00 6. " USB_HF_DEVICE ,Switch a slave interface of the USB HF device unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x00 3. " SDIO_0 ,Switch a slave interface of the SDIO 0 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x00 1. " HSRAM_0 ,Switch a slave interface of the HSRAM 0 unit and an error response circuit" "Slave interface,Error response circuit" else bitfld.long 0x00 9. " Boot_ROM ,Switch a slave interface of the Boot ROM unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x00 8. " US_HOST ,Switch a slave interface of the USB host unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x00 7. " US_HF_HOST ,Switch a slave interface of the USB HF host unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x00 6. " USB_HF_DEVICE ,Switch a slave interface of the USB HF device unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x00 5. " SDIO_2 ,Switch a slave interface of the SDIO 2 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x00 4. " SDIO_1 ,Switch a slave interface of the SDIO 1 unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x00 3. " SDIO_0 ,Switch a slave interface of the SDIO 0 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x00 1. " HSRAM_0 ,Switch a slave interface of the HSRAM 0 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x00 0. " MEDIA_LB ,Switch a slave interface of the Media LB unit and an error response circuit" "Slave interface,Error response circuit" endif line.long 0x04 "DSH1SEL,Default Slave AHB_1 Register" sif (cpu()=="MB86R24") bitfld.long 0x04 10. " ETHER ,Switch a slave interface of the Ethernet unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x04 9. " WDT_B ,Switch a slave interface of the Watchdog B unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x04 7. " I2S_2 ,Switch a slave interface of the I2S 2 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x04 6. " I2S_1 ,Switch a slave interface of the I2S 1 unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x04 5. " I2S_0 ,Switch a slave interface of the I2S 0 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x04 4. " SFI_1 ,Switch a Slave interface of the SFI 1 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x04 3. " SFI_0 ,Switch a slave interface of the SFI 0 unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x04 2. " RLD ,Switch a slave interface of the RLD unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x04 1. " HDMAC ,Switch a slave interface of the HDMAC unit and an error response circuit" "Slave interface,Error response circuit" else bitfld.long 0x04 11. " IDE66 ,Switch a slave interface of the IDE66 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x04 10. " ETHER ,Switch a slave interface of the Ethernet unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x04 9. " WDT_B ,Switch a slave interface of the Watchdog B unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x04 8. " I2S_3 ,Switch a slave interface of the I2S 3 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x04 7. " I2S_2 ,Switch a slave interface of the I2S 2 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x04 6. " I2S_1 ,Switch a slave interface of the I2S 1 unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x04 5. " I2S_0 ,Switch a slave interface of the I2S 0 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x04 4. " SFI_1 ,Switch a slave interface of the SFI 1 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x04 3. " SFI_0 ,Switch a slave interface of the SFI 0 unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x04 2. " RLD ,Switch a slave interface of the RLD unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x04 1. " HDMAC ,Switch a slave interface of the HDMAC unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x04 0. " HSRAM_1 ,Switch a slave interface of the HSRAM_1 unit and an error response circuit" "Slave interface,Error response circuit" endif line.long 0x08 "DSH2SEL,Default Slave AHB_2 Register" sif (cpu()=="MB86R24") bitfld.long 0x08 13. " SIG_1 ,Switch a slave interface of the SIG_1 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x08 12. " SIG_0 ,Switch a slave interface of the SIG_0 unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x08 10. " DDR3CREG_1 ,Switch a slave interface of the DDR3C_1 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x08 8. " CMDSEQ ,Switch a slave interface of the Command_Sequencer unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x08 7. " PIXEL_ENGINE ,Switch a slave interface of the Pixel_Engine unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x08 6. " DDR3CREG_0 ,Switch a slave interface of the DDR3C_0 register unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x08 1. " HS_SPI ,Switch a slave interface of the HS_SPI unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x08 0. " TCON ,Switch a slave interface of the TCON unit and an error response circuit" "Slave interface,Error response circuit" else bitfld.long 0x08 14. " SIG_2 ,Switch a slave interface of the SIG_2 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x08 13. " SIG_1 ,Switch a slave interface of the SIG_1 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x08 12. " SIG_0 ,Switch a slave interface of the SIG_0 unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x08 9. " DISPLAY_2 ,Switch a slave interface of the Display_2 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x08 8. " COMMAND_SEQUENCER ,Switch a slave interface of the Command_Sequencer unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x08 7. " PIXEL_ENGINE ,Switch a slave interface of the Pixel_Engine unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x08 6. " DDR_REGISTER ,Switch a slave interface of the DDR register unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x08 1. " HS_SPI ,Switch a slave interface of the HS_SPI unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x08 0. " TCON ,Switch a slave interface of the TCON unit and an error response circuit" "Slave interface,Error response circuit" endif line.long 0x0C "DSP0SEL,Default Slave APB_0 Register" bitfld.long 0x0C 9. " UART/USART_5 ,Switch a slave interface of the UART/USART 5 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x0C 8. " UART/USART_4 ,Switch a slave interface of the UART/USART 4 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x0C 7. " UART/USART_3 ,Switch a slave interface of the UART/USART 3 unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x0C 6. " UART/USART_2 ,Switch a slave interface of the UART/USART 2 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x0C 5. " UART/USART_1 ,Switch a slave interface of the UART/USART 1 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x0C 4. " UART/USART_0 ,Switch a slave interface of the UART/USART 0 unit and an error response circuit" "Slave interface,Error response circuit" line.long 0x10 "DSP0SEL,Default Slave AXI_0 Register" sif (cpu()=="MB86R24") bitfld.long 0x10 6. " DDR3C_1 ,Switch a slave interface of the DDR3C_1 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x10 5. " EBC ,Switch a slave interface of the EBC unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x10 4. " XSRAM ,Switch a slave interface of the XSRAM unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x10 3. " XDMAC ,Switch a slave interface of the XDMAC unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x10 2. " DDR3C_0 ,Switch a slave interface of the DDR3C_0 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x10 0. " DISPLAY/CAPTURE ,Switch a slave interface of the Display/Capture unit and an error response circuit" "Slave interface,Error response circuit" else bitfld.long 0x10 5. " ACP ,Switch a slave interface of the ACP unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x10 4. " XSRAM ,Switch a slave interface of the XSRAM unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x10 3. " XDMAC ,Switch a slave interface of the XDMAC unit and an error response circuit" "Slave interface,Error response circuit" textline " " bitfld.long 0x10 2. " DDR3 ,Switch a slave interface of the DDR3 unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x10 1. " 3DGE ,Switch a slave interface of the 3DGE unit and an error response circuit" "Slave interface,Error response circuit" bitfld.long 0x10 0. " DISPLAY/CAPTURE ,Switch a slave interface of the Display/Capture unit and an error response circuit" "Slave interface,Error response circuit" endif width 0x0B tree.end tree "EBC (External Bus Controller)" base ad:0x3C400000 width 8. group.long 0x0++0x03 line.long 0x00 "MODE0,Mode Register 0" bitfld.long 0x00 6. " RDY ,READY MODE" "Off,On" bitfld.long 0x00 5. " PAGE ,PAGE access mode" "Off,On" bitfld.long 0x00 4. " NAND ,NAND flash mode" "Off,On" textline " " sif (cpu()=="MB86R24") bitfld.long 0x00 3. " WEOFF ,Write enable off" "No,Yes" bitfld.long 0x00 2. " RBMON ,Read byte mask ON" "Off,On" textline " " endif bitfld.long 0x00 0.--1. " WIDTH ,Data bit width of a connected device" "8 bit,16 bit,32 bit,?..." group.long 0x4++0x03 line.long 0x00 "MODE1,Mode Register 1" bitfld.long 0x00 6. " RDY ,READY MODE" "Off,On" bitfld.long 0x00 5. " PAGE ,PAGE access mode" "Off,On" bitfld.long 0x00 4. " NAND ,NAND flash mode" "Off,On" textline " " sif (cpu()=="MB86R24") bitfld.long 0x00 3. " WEOFF ,Write enable off" "No,Yes" bitfld.long 0x00 2. " RBMON ,Read byte mask ON" "Off,On" textline " " endif bitfld.long 0x00 0.--1. " WIDTH ,Data bit width of a connected device" "8 bit,16 bit,32 bit,?..." group.long 0x8++0x03 line.long 0x00 "MODE2,Mode Register 2" bitfld.long 0x00 6. " RDY ,READY MODE" "Off,On" bitfld.long 0x00 5. " PAGE ,PAGE access mode" "Off,On" bitfld.long 0x00 4. " NAND ,NAND flash mode" "Off,On" textline " " sif (cpu()=="MB86R24") bitfld.long 0x00 3. " WEOFF ,Write enable off" "No,Yes" bitfld.long 0x00 2. " RBMON ,Read byte mask ON" "Off,On" textline " " endif bitfld.long 0x00 0.--1. " WIDTH ,Data bit width of a connected device" "8 bit,16 bit,32 bit,?..." group.long 0x20++0x03 line.long 0x00 "TIM0,Timing Register 0" bitfld.long 0x00 28.--31. " WIDLC ,Write idle cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles" bitfld.long 0x00 24.--27. " WWEC ,Write enable cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,?..." bitfld.long 0x00 20.--23. " WADC ,Write address setup cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,?..." bitfld.long 0x00 16.--19. " WACC ,Write access cycle" ",,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles" textline " " bitfld.long 0x00 12.--15. " RIDLC ,Read idle cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles" bitfld.long 0x00 8.--11. " FRADC ,First read address cycle" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles" bitfld.long 0x00 4.--7. " RADC ,Read address setup cycle" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles" bitfld.long 0x00 0.--3. " RACC ,Read access cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles" group.long 0x24++0x03 line.long 0x00 "TIM1,Timing Register 1" bitfld.long 0x00 28.--31. " WIDLC ,Write idle cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles" bitfld.long 0x00 24.--27. " WWEC ,Write enable cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,?..." bitfld.long 0x00 20.--23. " WADC ,Write address setup cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,?..." bitfld.long 0x00 16.--19. " WACC ,Write access cycle" ",,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles" textline " " bitfld.long 0x00 12.--15. " RIDLC ,Read idle cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles" bitfld.long 0x00 8.--11. " FRADC ,First read address cycle" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles" bitfld.long 0x00 4.--7. " RADC ,Read address setup cycle" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles" bitfld.long 0x00 0.--3. " RACC ,Read access cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles" group.long 0x28++0x03 line.long 0x00 "TIM2,Timing Register 2" bitfld.long 0x00 28.--31. " WIDLC ,Write idle cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles" bitfld.long 0x00 24.--27. " WWEC ,Write enable cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,?..." bitfld.long 0x00 20.--23. " WADC ,Write address setup cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,?..." bitfld.long 0x00 16.--19. " WACC ,Write access cycle" ",,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles" textline " " bitfld.long 0x00 12.--15. " RIDLC ,Read idle cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles" bitfld.long 0x00 8.--11. " FRADC ,First read address cycle" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles" bitfld.long 0x00 4.--7. " RADC ,Read address setup cycle" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles" bitfld.long 0x00 0.--3. " RACC ,Read access cycle" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles" sif (cpu()!="MB86R24") group.long 0x40++0x03 line.long 0x00 "AREA0,Area Register 0" hexmask.long.byte 0x00 16.--22. 1. " MASK ,Address mask" hexmask.long.byte 0x00 0.--7. 1. " ADDR ,Addresses to set the corresponding MEM_XCS[n] region" group.long 0x44++0x03 line.long 0x00 "AREA1,Area Register 1" hexmask.long.byte 0x00 16.--22. 1. " MASK ,Address mask" hexmask.long.byte 0x00 0.--7. 1. " ADDR ,Addresses to set the corresponding MEM_XCS[n] region" group.long 0x48++0x03 line.long 0x00 "AREA2,Area Register 2" hexmask.long.byte 0x00 16.--22. 1. " MASK ,Address mask" hexmask.long.byte 0x00 0.--7. 1. " ADDR ,Addresses to set the corresponding MEM_XCS[n] region" endif width 0x0B tree.end tree "DDR Controller" base ad:0x38400000 width 11. group.long 0x00++0x03 line.long 0x00 "MCR_0,MCR_0" hexmask.long.word 0x00 16.--31. 1. " VERSION ,Memory controller's version" bitfld.long 0x00 8.--11. " DRAM_CLASS ,The type of connected SDRAM is set" ",,,,DDR2 SDRAM,,DDR3 SDRAM,,,,,,,,," bitfld.long 0x00 0. " START ,The initialization of DRAM begins" "No operation,Initialization start" group.long 0x08++0x03 line.long 0x00 "MCR_2,MCR_2" hexmask.long.tbyte 0x00 0.--23. 1. " TINIT ,Sets cycles until stabilizing number of clock before CKE asserted" if (((per.l(ad:0x38400000))&0xF00)==0x600) group.long 0x0C++0x07 line.long 0x00 "MCR_3,MCR_3" line.long 0x04 "MCR_4,MCR_4" else hgroup.long 0x0C++0x07 hide.long 0x00 "MCR_3,MCR_3" hide.long 0x04 "MCR_4,MCR_4" endif group.long 0x14++0x03 line.long 0x00 "MCR_5,MCR_5" bitfld.long 0x00 24.--27. " WL ,Write latency is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 8.--12. " CL ,CAS latency" "-,-,1cycle,-,2cycle,-,3cycle,-,4cycle,-,5cycle,-,6cycle,-,7cycle,-,8cycle,-,9cycle,-,10cycle,-,11cycle,-,12cycle,-,13cycle,-,14cycle,-,15cycle,-" bitfld.long 0x00 0.--3. " INITAREF ,The number of auto-refresh commands when SDRAM is initialized is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" group.long 0x18++0x0B line.long 0x00 "MCR_6,MCR_6" bitfld.long 0x00 24.--29. " TRC ,SDRAM tRC parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 16.--18. " TRRD ,SDRAM tRRD parameter" "0,1,2,3,4,5,6,7" bitfld.long 0x00 8.--10. " TBST_INT_INTERVAL ,SDRAM int. parameter" "0,1,2,3,4,5,6,7" bitfld.long 0x00 0.--4. " TCCD ,SDRAM tCCD parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x04 "MCR_7,MCR_7" bitfld.long 0x04 24.--26. " TRTP ,SDRAM tRTP parameter" "0,1,2,3,4,5,6,7" bitfld.long 0x04 16.--19. " TRP ,SDRAM tRP parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x04 8.--11. " TWTR ,SDRAM tWTR parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" hexmask.long.byte 0x04 0.--7. 1. " TRAS_MIN ,SDRAM tRAS min parameter" line.long 0x08 "MCR_8,MCR_8" hexmask.long.word 0x08 16.--31. 1. " TRAS_MAX ,SDRAM tRAS max parameter" hexmask.long.byte 0x08 8.--15. 1. " TMOD ,SDRAM tMOD parameter" bitfld.long 0x08 0.--4. " TMRD ,SDRAM tMRD parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x24++0x0B line.long 0x00 "MCR_9,MCR_9" bitfld.long 0x00 24. " AP ,Please set 0h to this parameter" "0,1" bitfld.long 0x00 16.--20. " TCKESR ,SDRAM tCKESR parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 8.--10. " TCKE ,SDRAM tCKE parameter" "0,1,2,3,4,5,6,7" line.long 0x04 "MCR_10,MCR_10" bitfld.long 0x04 24.--28. " TWR_INT ,SDRAM tWR parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.word 0x04 16.--24. 1. " TRCD_INT ,SDRAM tRCD parameter" bitfld.long 0x04 0. " CONCURRENTAP ,Precharge is enable of two or more simultaneous banks" "Disabled,Enabled" line.long 0x08 "MCR_11,MCR_11" bitfld.long 0x08 24. " NO_CMD_INIT ,Please set 0h to this parameter" "0,1" hexmask.long.word 0x08 8.--23. 1. " TDLL ,SDRAM tDLL parameter" bitfld.long 0x08 0.--4. " TDAL ,SDRAM tDAL parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" if (((per.l(ad:0x38400000))&0xF00)==0x600) group.long 0x30++0x03 line.long 0x00 "MCR_12,MCR_12" hexmask.long.word 0x00 16.--31. 1. " TCPD ,Cycle number between CKE - precharge command" bitfld.long 0x00 8.--13. " TFAW ,SDRAM TFAW parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 0.--2. " BSTLEN ,The burst-length is set" ",,,8busrt,,,," else group.long 0x30++0x03 line.long 0x00 "MCR_12,MCR_12" hexmask.long.word 0x00 16.--31. 1. " TCPD ,Cycle number between CKE - precharge command" bitfld.long 0x00 8.--13. " TFAW ,SDRAM TFAW parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 0.--2. " BSTLEN ,The burst-length is set" ",,4burst,8busrt,,,," endif textline " " group.long 0x34++0x13 line.long 0x00 "MCR_13,MCR_13" bitfld.long 0x00 24. " MANUAL_REFRESH_MODE ,Setting of mode of manual refresh" "Burst boundary,Transaction boundary" bitfld.long 0x00 16. " MREFRESH ,Refresh is executed based on the manual_refresh_mode parameter" "No action,Refresh is issued" bitfld.long 0x00 0.--3. " TRP_AB ,SDRAM tRP parameter of all banks is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " line.long 0x04 "MCR_14,MCR_14" hexmask.long.word 0x04 8.--17. 1. " TRFC ,SDRAM tRFC parameter" bitfld.long 0x04 0. " TREF_ENABLE ,Auto refresh is executed at tref parameter intervals" "Disabled,Enabled" line.long 0x08 "MCR_15,MCR_15" hexmask.long.word 0x08 0.--13. 1. " TREF ,SDRAM tREF parameter" line.long 0x10 "MCR_16,MCR_16" hexmask.long.word 0x10 16.--31. 1. " TXPDLL ,SDRAM tXPDLL parameter" hexmask.long.word 0x10 0.--15. 1. " TPDEX ,SDRAM tXP parameter" if (((per.l(ad:0x38400000+0x41C))&0x01)==0x01) group.long 0x44++0x03 line.long 0x00 "MCR_17,MCR_17" hexmask.long.word 0x00 16.--31. 1. " TXSNR ,SDRAM tXSDLL parameter" hexmask.long.word 0x00 0.--15. 1. " TXSR ,SDRAM tXS parameter" else group.long 0x44++0x03 line.long 0x00 "MCR_17,MCR_17" hexmask.long.word 0x00 16.--31. 1. " TXSNR ,SDRAM tXSRD parameter" hexmask.long.word 0x00 0.--15. 1. " TXSR ,SDRAM tXSN parameter" endif group.long 0x48++0x0F line.long 0x00 "MCR_18,MCR_18" bitfld.long 0x00 24.--26. " CKE_DELAY ,Cycle until CKE is reflected in the cke_status parameter number is set" "0,1,2,3,4,5,6,7" bitfld.long 0x00 16. " ENABLE_QUICK_SREFRESH ,Please set 1h to this parameter" "0,1" bitfld.long 0x00 0. " SREFRESH ,It shifts to the self-refresh mode" "Disabled,Enabled" line.long 0x04 "MCR_19,MCR_19" hexmask.long.word 0x04 8.--23. 1. " MR0_DATA_0 ,Setting of Mode Register MR0(DDR3), MR(DDR2)" bitfld.long 0x04 0. " WRITE_MODEREG ,write_modereg" "No action,Write mode" line.long 0x08 "MCR_20,MCR_20" hexmask.long.word 0x08 16.--31. 1. " MR2_DATA_0 ,Setting of Mode Register MR2(DDR3), EMR(2)(DDR2)" hexmask.long.word 0x08 0.--15. 1. " MR1_DATA_0 ,Setting of Mode Register MR1(DDR3), EMR(1)(DDR2)" line.long 0x0C "MCR_21,MCR_21" hexmask.long.word 0x0C 16.--27. 1. " ZQINIT ,ZQ calibration command cycle number when SDRAM is initialized is set" hexmask.long.word 0x0C 0.--15. 1. " MR3_DATA_0 ,Setting of Mode Register MR3(DDR3), EMR(3)(DDR2)" if (((per.l(ad:0x38400000+0x41C))&0x01)==0x01) group.long 0x58++0x03 line.long 0x00 "MCR_22,MCR_22" bitfld.long 0x00 16.--17. " ZQ_REQ ,The ZQ calibration is executed" "No action,ZQCS,ZQCL," hexmask.long.word 0x00 0.--11. 1. " ZQCL ,ZQCL command cycle number is set" else group.long 0x58++0x03 line.long 0x00 "MCR_22,MCR_22" hexmask.long.word 0x00 0.--11. 1. " ZQCL ,ZQCL command cycle number is set" endif group.long 0x5C++0x03 line.long 0x00 "MCR_23,MCR_23" bitfld.long 0x00 24.--25. " ZQ_ON_SREF_EXIT ,The ZQ calibration set to this parameter is executed at self-refresh exit" ",ZQCS,ZQCL," hexmask.long.byte 0x00 16.--23. 1. " REFRESH_PER_ZQ ,Maximum refresh number is set between automatic ZQCS" hexmask.long.word 0x00 0.--11. 1. " ZQCS ,ZQCS command cycle number is set" if (((per.l(ad:0x38400000+0x41C))&0x01)==0x01) group.long 0x60++0x03 line.long 0x00 "MCR_24,MCR_24" bitfld.long 0x00 24.--26. " COLUMN_SIZE ,Differences between the number of maximum column address pins and the number of column address pins" "0,1,2,3,4,5,6,7" bitfld.long 0x00 16.--18. " ADDR_PINS ,Differences between the number of DFI of address pins and the number of address pins of actual SDRAM" "0,1,2,3,4,5,6,7" bitfld.long 0x00 8. " EIGHT_BANK_MODE ,The number of banks of SDRAM is set" "4 banks,8 banks" rbitfld.long 0x00 0. " ZQ_IN_PROGRESS ,It becomes 1 while executing the ZQ calibration" "Cal. completion,Being executed" else group.long 0x60++0x03 line.long 0x00 "MCR_24,MCR_24" bitfld.long 0x00 24.--26. " COLUMN_SIZE ,Differences between the number of maximum column address pins and the number of column address pins" "0,1,2,3,4,5,6,7" bitfld.long 0x00 16.--18. " ADDR_PINS ,Differences between the number of DFI of address pins and the number of address pins of actual SDRAM" "0,1,2,3,4,5,6,7" bitfld.long 0x00 8. " EIGHT_BANK_MODE ,The number of banks of SDRAM is set" "4 banks,8 banks" endif group.long 0x64++0x0B line.long 0x00 "MCR_25,MCR_25" bitfld.long 0x00 24. " ADDR_CMP_EN ,It collides the address, and the data coherency detection is enable" "Disabled,Enabled" hexmask.long.byte 0x00 16.--23. 1. " COMMAND_AGE_COUNT ,Command_age_count" hexmask.long.byte 0x00 8.--15. 1. " AGE_COUNT ,Age_count" bitfld.long 0x00 0.--3. " APREBIT ,The Auto pre-charge bit of SDRAM address pins is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x04 "MCR_26,MCR_26" bitfld.long 0x04 24. " RW_SAME_EN ,It is enable at placement_en of the function that permutes it as write command and write command or read command" "Disabled,Enabled" bitfld.long 0x04 16. " PRIORITY_EN ,It is enable at placement_en of the function to insert the command with a high priority previously" "Disabled,Enabled" bitfld.long 0x04 8. " PLACEMENT_EN ,Command replacement function (placement logic) is used" "Disabled,Enabled" bitfld.long 0x04 0. " BANK_SPLIT_EN ,It is enable at placement_en of the function to make it not continue the command to another page of the same bank" "Disabled,Enabled" line.long 0x08 "MCR_27,MCR_27" bitfld.long 0x08 24. " REDUC ,Setting of width of DRAM data bus. MDQ15 ~ MDQ0 becomes effective at 16bit mode" "32bit,16bit" bitfld.long 0x08 16.--19. " BURST_ON_FLY_BIT ,Please set 1100 to this bit" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x08 0. " SWAP_EN ,When the placement_en is 1, it replaces it with the command with high priority" "Disabled,Enabled" group.long 0x70++0x0B line.long 0x00 "MCR_28,MCR_28" bitfld.long 0x00 24. " RESYNC_DLL ,Please set this parameter to 0" "0,1" bitfld.long 0x00 16.--18. " Q_FULLNESS ,Please set this parameter to 000" "0,1,2,3,4,5,6,7" bitfld.long 0x00 8. " FAST_WRITE ,Please set this parameter to 0" "0,1" bitfld.long 0x00 0. " CMDLAT_REDUC_EN ,Please set this parameter to 0" "0,1" textline " " line.long 0x04 "MCR_29,MCR_29" rbitfld.long 0x04 23. " INT_STATUS_[23] ,Logical add of bit[22]-bit[8]" "No interrupt,Interrupt" rbitfld.long 0x04 22. " [22] ,DLL re-synchronous completion that user executed" "No interrupt,Interrupt" rbitfld.long 0x04 21. " [21] ,DFI initialization completion" "No interrupt,Interrupt" rbitfld.long 0x04 20. " [20] ,Register write completion in register interface mode and register write issue in other register interface modes" "No interrupt,Interrupt" textline " " rbitfld.long 0x04 19. " [19] ,Leveling operation completion" "No interrupt,Interrupt" rbitfld.long 0x04 18. " [18] ,Levering operation request" "No interrupt,Interrupt" rbitfld.long 0x04 17. " [17] ,Write leveling error" "No interrupt,Interrupt" rbitfld.long 0x04 16. " [16] ,Gate training error" "No interrupt,Interrupt" textline " " rbitfld.long 0x04 14. " [14] ,Enable ODT and CAS latency = 3 set error" "No interrupt,Interrupt" rbitfld.long 0x04 13. " [13] ,DRAM initialization completion" "No interrupt,Interrupt" rbitfld.long 0x04 12. " [12] ,Command data channel error in port" "No interrupt,Interrupt" rbitfld.long 0x04 11. " [11] ,Command channel error in port" "No interrupt,Interrupt" textline " " rbitfld.long 0x04 10. " [10] ,Multi outside physical memory area access detection" "No interrupt,Interrupt" rbitfld.long 0x04 9. " [9] ,Detection of single access outside physical memory area" "No interrupt,Interrupt" rbitfld.long 0x04 8. " [8] ,Memory reset is effective in DFI" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " RESYNC_DLL_PER_SREF_EN ,Please set this parameter to 1" "0,1" textline "" line.long 0x08 "MCR_30,MCR_30" hexmask.long.word 0x08 16.--31. 1. " INT_MASK ,It mask bit that the int_status parameter corresponds by setting 1" hexmask.long.word 0x08 0.--15. 1. " INT_ACK ,It clear to 0 corresponding bit of int_status" rgroup.long 0x7C++0x17 line.long 0x00 "MCR_31,MCR_31" line.long 0x04 "MCR_32,MCR_32" bitfld.long 0x04 8.--13. " OUT_OF_RANGE_TYPE ,The command type that becomes the factor of out_of_range interrupt is stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.byte 0x04 0.--6. 1. " OUT_OF_RANGE_LENGTH ,The length of the command that becomes the factor of out_of_range interrupt is stored" line.long 0x08 "MCR_33,MCR_33" hexmask.long.tbyte 0x08 0.--16. 1. " OUT_OF_RANGE_SOURCE_ID ,Source ID of the command that becomes the factor of out_of_range interrupt is stored" line.long 0x0C "MCR_34,MCR_34" line.long 0x10 "MCR_35,MCR_35" bitfld.long 0x10 27. " PORT_CMD_ERROR_TYPE ,Narrow forwarding request from port Y where axiY_en_size_lt_width_instr parameter is not set" "0,1" hexmask.long.tbyte 0x10 0.--16. 1. " Port_cmd_error_id ,Source ID of the command that becomes the factor of the port command error is stored" line.long 0x14 "MCR_36,MCR_36" hexmask.long.tbyte 0x14 0.--16. 1. " PORT_DATA_ERROR_ID ,Source ID of the command that becomes the factor of the port data error is stored" group.long 0x94++0x0B line.long 0x00 "MCR_37,MCR_37" bitfld.long 0x00 24.--26. " R2W_SAMECS_DLY ,The number of clocks of delay added between the read command and write commands is set" "0,1,2,3,4,5,6,7" bitfld.long 0x00 16.--18. " F2R_SAMECS_DLY ,Please set 0000 to this bit" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 8.--11. " ADD_ODT_CLK_W2R_SAMECS ,Please set 0000 to this bit" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 0.--3. " ADD_ODT_CLK_R2W_SAMECS ,The number of clocks of delay added after the read command ahead of the write command to make ODT conform to this occasion" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x04 "MCR_38,MCR_38" bitfld.long 0x04 8.--10. " W2R_SAMECS_DLY ,Please set 000 to this bit" "0,1,2,3,4,5,6,7" bitfld.long 0x04 0.--2. " W2W_SAMECS_DLY ,Please set 000 to this bit" "0,1,2,3,4,5,6,7" line.long 0x08 "MCR_39,MCR_39" bitfld.long 0x08 24. " SWLVL_EXIT ,It returns from levelling operation to the ordinary mode" "No action,Exit" bitfld.long 0x08 16. " SWLVL_START ,Levelling operation is begun based on the sw_leveling_mode parameter" "No action,Started" textline " " bitfld.long 0x08 8. " SWLVL_LOAD ,The delay value is issued and the load doing and the read burst or the write strobe are issued" "No action,Delay/levelling" bitfld.long 0x08 0.--1. " SW_LEVELING_MODE ,The type of levelling operation is set" "No levelling,Write levelling,,Gate training" rgroup.long 0xA0++0x1F line.long 0x00 "MCR_40,MCR_40" bitfld.long 0x00 24. " SWLVL_RESP_1 ,The response of levelling operation against data[15:8] is stored" "0,1" bitfld.long 0x00 16. " SWLVL_RESP_0 ,The response of levelling operation against data[7:0] is stored" "0,1" textline " " bitfld.long 0x00 0. " SWLVL_OP_DONE ,The state of levelling operation is shown" "Operation in process,Operation completed" textline " " group.long 0xA4++0x1B line.long 0x00 "MCR_41,MCR_41" bitfld.long 0x00 24. " WRLVL_CS ,Please set 0 to this bit" "0,1" rbitfld.long 0x00 8. " SWLVL_RESP_3 ,The response of levelling operation against data[32:24] is stored" "0,1" textline " " rbitfld.long 0x00 0. " SWLVL_RESP_2 ,The response of leveling operation against data[23:16] is stored" "0,1" line.long 0x04 "MCR_42,MCR_42" bitfld.long 0x04 8.--13. " WLMRD ,Please set 28h to this parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x04 0.--5. " WLDQSEN ,Please set 19h to this parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x08 "MCR_43,MCR_43" hexmask.long.word 0x08 0.--15. 1. " WRLVL_REFRESH_INTERVAL ,Please set 0 to this parameter" line.long 0x0C "MCR_44,MCR_44" hexmask.long.byte 0x0C 8.--15. 1. " WRLVL_DELAY_0 ,Write levelling delay value against deta[7:0] is set" line.long 0x10 "MCR_45,MCR_45" hexmask.long.byte 0x10 16.--23. 1. " WRLVL_DELAY_2 ,Write levelling delay value against deta[23:16] is set" hexmask.long.byte 0x10 0.--7. 1. " WRLVL_DELAY_1 ,Write leveling delay value against deta[15:8] is set" line.long 0x14 "MCR_46,MCR_46" hexmask.long.byte 0x14 0.--7. 1. " WRLVL_DELAY_3 ,Write leveling delay value against deta[31:24] is set" line.long 0x18 "MCR_47,MCR_47" bitfld.long 0x18 0. " RDLVL_CS ,Please set this parameter to 0" "0,1" group.long 0xCC++0x03 line.long 0x00 "MCR_51,MCR_51" hexmask.long.byte 0x00 16.--23. 1. " RDLVL_GATE_DELAY_0 ,Gate training delay value against deta[7:0] is set" group.long 0xDC++0x03 line.long 0x00 "MCR_55,MCR_55" hexmask.long.byte 0x00 0.--7. 1. " RDLVL_GATE_DELAY_1 ,Gate training delay value against deta[15:8] is set" group.long 0xE8++0x03 line.long 0x00 "MCR_58,MCR_58" hexmask.long.byte 0x00 16.--23. 1. " RDLVL_GATE_DELAY_2 ,Gate training delay value against deta[23:16] is set" group.long 0xF8++0x23 line.long 0x00 "MCR_62,MCR_62" hexmask.long.word 0x00 16.--31. 1. " AXI0_EN_SIZE_WIDTH_INSTR ,ID of AXI that permits a narrow forwarding to port 0 is set" hexmask.long.word 0x00 0.--8. 1. " RDLVL_GATE_DELAY_3 ,Gate training delay value against deta[31:24] is set" line.long 0x04 "MCR_63,MCR_63" bitfld.long 0x04 16.--17. " AXI0_FIFO_TYPE_REG ,The clock relation between AXI clock and controller of the memory to port 0 is set" "Asynchronous,,," bitfld.long 0x04 8.--9. " AXI0_W_PRIORITY ,The priority of the write command to port 0 is set" "0,1,2,3" textline " " bitfld.long 0x04 0.--1. " AXI0_R_PRIORITY ,The priority of the read command to port 0 is set" "0,1,2,3" line.long 0x08 "MCR_64,MCR_64" bitfld.long 0x08 24.--25. " AXI1_W_PRIORITY ,The priority of the write command to port 1 is set" "0,1,2,3" bitfld.long 0x08 16.--17. " AXI1_R_PRIORITY ,The priority of the read command to port 1 is set" "0,1,2,3" textline " " hexmask.long.word 0x08 0.--15. 1. " AXI1_EN_SIZE_WIDTH_INSTR ,ID of AXI that permits a narrow forwarding to port 1 is set" line.long 0x0C "MCR_65,MCR_65" bitfld.long 0x0C 24.--25. " AXI2_R_PRIORITY ,The priority of the read command to port 2 is set" "0,1,2,3" hexmask.long.word 0x0C 8.--23. 1. " AXI2_EN_SIZE_WIDTH_INSTR ,ID of AXI that permits a narrow forwarding to port 2 is set" textline " " bitfld.long 0x0C 0.--1. " AXI1_FIFO_TYPE_REG ,The clock relation between AXI clock and controller of the memory to port 1 is set" "Asynchronous,,," line.long 0x10 "MCR_66,MCR_66" hexmask.long.word 0x10 16.--31. 1. " AXI3_EN_SIZE_WIDTH_INSTR ,ID of AXI that permits a narrow forwarding to port 3 is set" bitfld.long 0x10 8.--9. " AXI2_FIFO_TYPE_REG ,The clock relation between AXI clock and controller of the memory to port 2 is set" "Asynchronous,,," textline " " bitfld.long 0x10 0.--1. " AXI2_W_PRIORITY ,The priority of the write command to port 2 is set" "0,1,2,3" line.long 0x14 "MCR_67,MCR_67" bitfld.long 0x14 16.--17. " AXI3_FIFO_TYPE_REG ,The clock relation between AXI clock and controller of the memory to port 3 is set" "Asynchronous,,," bitfld.long 0x14 8.--9. " AXI3_W_PRIORITY ,The priority of the write command to port 3 is set" "0,1,2,3" textline " " bitfld.long 0x14 0.--1. " AXI3_R_PRIORITY ,The priority of the read command to port 3 is set" "0,1,2,3" line.long 0x18 "MCR_68,MCR_68" bitfld.long 0x18 23.--24. " AXI4_W_PRIORITY ,The priority of the write command to port 4 is set" "0,1,2,3" bitfld.long 0x18 16.--17. " AXI4_R_PRIORITY ,The priority of the read command to port 4 is set" "0,1,2,3" textline " " hexmask.long.word 0x18 0.--15. 1. " AXI4_EN_SIZE_WIDTH_INSTR ,ID of AXI that permits a narrow forwarding to port 4 is set" line.long 0x1C "MCR_69,MCR_69" rbitfld.long 0x1C 24.--25. " WRR_PARAM_VALUE_ERR ,Error/warning of the weighted round robin arbitration is shown" "0,1,2,3" bitfld.long 0x1C 8. " WEIGHTED_ROUND_ROBIN_LATENCY_CONTROL ,The count up method of the counter in Priority Relaxing is set" "Count up,Self-propelled type" textline " " bitfld.long 0x1C 0.--1. " AXI4_FIFO_TYPE_REG ,The clock relation between AXI clock and controller of the memory to port 4 is set" "Asynchronous,,," textline " " line.long 0x20 "MCR_70,MCR_70" bitfld.long 0x20 24.--27. " AXI0_PRIORITY[3]_relative_priority ,The value of relative priority of port 0 to the command of priority 3 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x20 16.--19. " [2] ,The value of relative priority of port 0 to the command of priority 2 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x20 8.--11. " [1] ,The value of relative priority of port 0 to the command of priority 1 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x20 0.--3. " [0] ,The value of relative priority of port 0 to the command of priority 0 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " group.long 0x11C++0x23 line.long 0x00 "MCR_71,MCR_71" bitfld.long 0x00 24.--27. " AXI1_PRIORITY0_RELATIVE_PRIORITY ,The value of relative priority of port 1 to the command of priority 0 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" hexmask.long.word 0x00 8.--17. 1. " AXI0_PRIORITY_RELAX ,The counter value of port 0 in priority relax is set" textline " " bitfld.long 0x00 0.--2. " AXI0_PORT_ORDERING ,The order of scan order of port 0 is set" "0,1,2,3,4,5,6,7" line.long 0x04 "MCR_72,MCR_72" bitfld.long 0x04 24.--26. " AXI1_PORT_ORDERING ,The order of scan order of port 1 is set" "0,1,2,3,4,5,6,7" bitfld.long 0x04 16.--19. " AXI1_PRIORITY3_RELATIVE_PRIORITY ,The value of relative priority of port 1 to the command of priority 3 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x04 8.--11. " AXI1_PRIORITY2_RELATIVE_PRIORITY ,The value of relative priority of port 1 to the command of priority 2 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x04 0.--3. " AXI1_PRIORITY1_RELATIVE_PRIORITY ,The value of relative priority of port 1 to the command of priority 1 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "MCR_73,MCR_73" bitfld.long 0x08 24.--27. " AXI2_PRIORITY1_RELATIVE_PRIORITY ,The value of relative priority of port 2 to the command of priority 1 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x08 16.--19. " AXI2_PRIORITY0_RELATIVE_PRIORITY ,The value of relative priority of port 2 to the command of priority 0 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " hexmask.long.word 0x08 0.--9. 1. " AXI1_PRIORITY_RELAX ,The counter value of port 1 in priority relax is set" line.long 0x0C "MCR_74,MCR_74" bitfld.long 0x0C 16.--18. " AXI2_PORT_ORDERING ,The order of scan order of port 2 is set" "0,1,2,3,4,5,6,7" bitfld.long 0x0C 8.--11. " AXI2_PRIORITY3_RELATIVE_PRIORITY ,The value of relative priority of port 2 to the command of priority 3 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x0C 0.--3. " AXI2_PRIORITY2_RELATIVE_PRIORITY ,The value of relative priority of port 2 to the command of priority 2 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x10 "MCR_75,MCR_75" bitfld.long 0x10 24.--27. " AXI3_PRIORITY1_RELATIVE_PRIORITY ,The value of relative priority of port 3 to the command of priority 1 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x10 16.--19. " AXI3_PRIORITY0_RELATIVE_PRIORITY ,The value of relative priority of port 3 to the command of priority 0 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " hexmask.long.word 0x10 0.--9. 1. " AXI2_PRIORITY_RELAX ,The counter value of port 2 in priority relax is set" line.long 0x14 "MCR_76,MCR_76" bitfld.long 0x14 16.--18. " AXI3_PORT_ORDERING ,The order of scan order of port 3 is set" "0,1,2,3,4,5,6,7" bitfld.long 0x14 8.--11. " AXI3_PRIORITY3_RELATIVE_PRIORITY ,The value of relative priority of port 3 to the command of priority 3 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x14 0.--3. " AXI3_PRIORITY2_RELATIVE_PRIORITY ,The value of relative priority of port 3 to the command of priority 2 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x18 "MCR_77,MCR_77" bitfld.long 0x18 24.--27. " AXI4_PRIORITY1_RELATIVE_PRIORITY ,The value of relative priority of port 4 to the command of priority 1 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x18 16.--19. " AXI4_PRIORITY0_RELATIVE_PRIORITY ,The value of relative priority of port 4 to the command of priority 0 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " hexmask.long.word 0x18 0.--9. 1. " AXI3_PRIORITY_RELAX ,The counter value of port 3 in priority relax is set" line.long 0x1C "MCR_78,MCR_78" bitfld.long 0x1C 16.--18. " AXI4_PORT_ORDERING ,The order of scan order of port 4 is set" "0,1,2,3,4,5,6,7" bitfld.long 0x1C 8.--11. " AXI4_PRIORITY3_RELATIVE_PRIORITY ,The value of relative priority of port 4 to the command of priority 3 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x1C 0.--3. " AXI4_PRIORITY2_RELATIVE_PRIORITY ,The value of relative priority of port 4 to the command of priority 2 is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " line.long 0x20 "MCR_79,MCR_79" rbitfld.long 0x20 16. " CKE_STATUS ,It is shown that SDRAM is self-refresh mode. Read only" "Self-refresh mode,Nomal mode" hexmask.long.word 0x20 0.--9. 1. " AXI4_PRIORITY_RELAX ,The counter value of port 4 in priority relax is set" group.long 0x140++0x0B line.long 0x00 "MCR_80,MCR_80" rbitfld.long 0x00 24.--27. " TDFI_PHY_WRLAT ,The tphy_wrlat parameter of DFI is shown" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" hexmask.long.byte 0x00 16.--23. 1. " DLL_RST_ADJ_DLY ,Please set 0h to this parameter" textline " " hexmask.long.word 0x00 0.--15. 1. " DLL_RST_DELAY ,Please set 0h to this parameter" line.long 0x04 "MCR_81,MCR_81" bitfld.long 0x04 24.--28. " TDFI_RDDATA_EN_BASE ,Please set 02h to this parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rbitfld.long 0x04 16.--20. " TDFI_RDDATA_EN ,The trddata_en parameter of DFI is shown" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x04 8.--12. " TDFI_PHY_RDLAT ,The tphy_rdlat parameter of DFI is set" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x04 0.--3. " TDFI_PHY_WRLAT_BASE ,Please set 02h to this parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "MCR_82,MCR_82" hexmask.long.word 0x08 16.--29. 1. " TDFI_CTRLUPD_MAX ,The tctrlupd_max parameter of DFI is set" rbitfld.long 0x08 8.--11. " TDFI_CTRLUPD_MIN ,The tctrlupd_min parameter of DFI is shown" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x08 0. " DRAM_CLK_DISABLE ,ON/OFF of DRAM clock is set" "On,Off" group.long 0x154++0x0B line.long 0x00 "MCR_85,MCR_85" bitfld.long 0x00 24.--27. " WRLAT_ADJ ,To be suitable for the timing demand of PHY in this parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 16.--20. " RDLAT_ADJ ,To be suitable for the timing demand of PHY in this parameter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x04 "MCR_86,MCR_86" hexmask.long.byte 0x04 24.--31. 1. " TDFI_WRLVL_DLL ,The minimum number of cycles from write leveling load signal to first write leveling strobe signal" hexmask.long.byte 0x04 16.--23. 1. " TDFI_WRLVL_EN ,The minimum number of cycles from write leveling enable signal to first write leveling load signal" line.long 0x08 "MCR_87,MCR_87" hexmask.long.word 0x08 16.--25. 1. " TDFI_WRLVL_WW ,The minimum number of cycles from write leveling strobe signal to the following write leveling strobe signal" hexmask.long.byte 0x08 8.--15. 1. " TDFI_WRLVL_RESPLAT ,Maximum number of cycles from the write leveling strobe signal to the response is effective" textline " " hexmask.long.byte 0x08 0.--7. 1. " TDFI_WRLVL_LOAD ,The minimum number of cycles from write leveling delay value setting to write leveling load signal" group.long 0x16C++0x07 line.long 0x00 "MCR_91,MCR_91" hexmask.long.byte 0x00 24.--31. 1. " TDFI_RDLVL_RESPLAT ,The Maximum number of cycles until the response becomes effective from the read command" hexmask.long.byte 0x00 16.--23. 1. " TDFI_RDLVL_LOAD ,The minimum number of cycles from the gate training delay value setting to the gate training load signal" textline " " hexmask.long.byte 0x00 8.--15. 1. " TDFI_RDLVL_DLL ,The minimum number of cycles from the gate training load signal to the following read command" hexmask.long.byte 0x00 0.--7. 1. " TDFI_RDLVL_EN ,The minimum number of cycles from gate training enable signal to gate training load signal" line.long 0x04 "MCR_92,MCR_92" hexmask.long.word 0x04 0.--9. 1. " TDFI_RDLVL_RR ,The minimum number of cycles from the read command to the following read command" textline " " rgroup.long 0x400++0x03 line.long 0x00 "REG_STR,Status information output from Memory Controller" bitfld.long 0x00 19. " R_DATA_BYTE_DISABLE[3] ,The effective byte lane of the data bus is shown" "Enabled,Disabled" bitfld.long 0x00 18. " [2] ,The effective byte lane of the data bus is shown" "Enabled,Disabled" bitfld.long 0x00 17. " [1] ,The effective byte lane of the data bus is shown" "Enabled,Disabled" bitfld.long 0x00 16. " [0] ,The effective byte lane of the data bus is shown" "Enabled,Disabled" textline " " bitfld.long 0x00 12. " R_PORT_BUSY[4] ,The busy state of the port is shown" "Not busy,Busy" bitfld.long 0x00 11. " [3] ,The busy state of the port is shown" "Not busy,Busy" bitfld.long 0x00 10. " [2] ,The busy state of the port is shown" "Not busy,Busy" bitfld.long 0x00 9. " [1] ,The busy state of the port is shown" "Not busy,Busy" bitfld.long 0x00 8. " [0] ,The busy state of the port is shown" "Not busy,Busy" textline " " bitfld.long 0x00 4. " R_REFRESH_IN_PROCESS ,Refreshing SDRAM is shown" "Not executing,Executing" textline " " bitfld.long 0x00 3. " R_CONTROLLER_BUSY ,Memory controller's busy state is shown" "Not busy,Busy" textline " " group.long 0x404++0x17 line.long 0x00 "REG_MCC,This register can control the signal output to Memory Controller" bitfld.long 0x00 24. " R_MPR_MASK ,It mask the commands output from Memory Controller when Gate training for DDR2 mode." "Not masked,Masked" bitfld.long 0x00 16.--20. " R_AXIY_AWCOBUF ,R_AXIY_AWCOBUF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 0. " R_DFI_INIT_COMP ,Please change this bit to '1' before issuing the first command" "Not complete,Complete" line.long 0x04 "REG_RST,This register can control reset of PHY" bitfld.long 0x04 18. " RX_SOFTRSTX ,Reset for the read counter of PHY" "Reset,Release" bitfld.long 0x04 17. " RX_PZQRSTX ,Reset for the calibration circuit of PHY" "Reset,Release" bitfld.long 0x04 16. " RX_DLLRSTX ,Reset for DLL of PHY" "Reset,Release" bitfld.long 0x04 3. " RX_RSTX_PZQ ,Reset of PHY" "Reset,Release" textline " " bitfld.long 0x04 2. " RX_RSTX_DQDQS ,Reset of PHY" "Reset,Release" bitfld.long 0x04 1. " RX_RSTX_CMD ,Reset of PHY" "Reset,Release" bitfld.long 0x04 0. " RX_RSTX_CK ,Reset of PHY" "Reset,Release" textline " " line.long 0x08 "REG_PWR0,This register can do Driver suspend of I/O" bitfld.long 0x08 23. " R_SUSPD_CMD_[23] ,Driver suspend of I/O for MCKE" "Enabled,Suspend" bitfld.long 0x08 22. " [22] ,Driver suspend of I/O for MODT" "Enabled,Suspend" bitfld.long 0x08 21. " [21] ,Driver suspend of I/O for MXCS" "Enabled,Suspend" bitfld.long 0x08 20. " [20] ,Driver suspend of I/O for MXRAS" "Enabled,Suspend" bitfld.long 0x08 19. " [19] ,Driver suspend of I/O for MXCAS" "Enabled,Suspend" textline " " bitfld.long 0x08 18. " [18] ,Driver suspend of I/O for MXWE" "Enabled,Suspend" bitfld.long 0x08 17. " [17] ,Driver suspend of I/O for MBA2" "Enabled,Suspend" bitfld.long 0x08 16. " [16] ,Driver suspend of I/O for MBA1" "Enabled,Suspend" bitfld.long 0x08 15. " [15] ,Driver suspend of I/O for MBA0" "Enabled,Suspend" bitfld.long 0x08 14. " [14] ,Driver suspend of I/O for MA14" "Enabled,Suspend" textline " " bitfld.long 0x08 13. " [13] ,Driver suspend of I/O for MA13" "Enabled,Suspend" bitfld.long 0x08 12. " [12] ,Driver suspend of I/O for MA12" "Enabled,Suspend" bitfld.long 0x08 11. " [11] ,Driver suspend of I/O for MA11" "Enabled,Suspend" bitfld.long 0x08 10. " [10] ,Driver suspend of I/O for MA10" "Enabled,Suspend" bitfld.long 0x08 9. " [9] ,Driver suspend of I/O for MA9" "Enabled,Suspend" textline " " bitfld.long 0x08 8. " [8] ,Driver suspend of I/O for MA8" "Enabled,Suspend" bitfld.long 0x08 7. " [7] ,Driver suspend of I/O for MA7" "Enabled,Suspend" bitfld.long 0x08 6. " [6] ,Driver suspend of I/O for MA6" "Enabled,Suspend" bitfld.long 0x08 5. " [5] ,Driver suspend of I/O for MA5" "Enabled,Suspend" bitfld.long 0x08 4. " [4] ,Driver suspend of I/O for MA4" "Enabled,Suspend" textline " " bitfld.long 0x08 3. " [3] ,Driver suspend of I/O for MA3" "Enabled,Suspend" bitfld.long 0x08 2. " [2] ,Driver suspend of I/O for MA2" "Enabled,Suspend" bitfld.long 0x08 1. " [1] ,Driver suspend of I/O for MA1" "Enabled,Suspend" bitfld.long 0x08 0. " [0] ,Driver suspend of I/O for MA0" "Enabled,Suspend" textline " " line.long 0x0C "REG_PWR1,This register can suspend an I/O cells driver or receiver operation" bitfld.long 0x0C 19. " R_SUSP_LBIO_[3] ,Receiver suspend of LoopBack I/O 3" "Enabled,Suspend" bitfld.long 0x0C 18. " [2] ,Receiver suspend of LoopBack I/O 2" "Enabled,Suspend" bitfld.long 0x0C 17. " [1] ,Receiver suspend of LoopBack I/O 1" "Enabled,Suspend" bitfld.long 0x0C 16. " [0] ,Receiver suspend of LoopBack I/O 0" "Enabled,Suspend" textline " " bitfld.long 0x0C 15. " R_SUSPR_DQ_[3] ,Receiver suspend of MDQ24~MDQ31,MDQS3,MXDQS3" "Enabled,Suspend" bitfld.long 0x0C 14. " [2] ,Receiver suspend of MDQ16~MDQ23,MDQS2,MXDQS2" "Enabled,Suspend" bitfld.long 0x0C 13. " [1] ,Receiver suspend of MDQ8~MDQ15,MDQS1,MXDQS1" "Enabled,Suspend" bitfld.long 0x0C 12. " [0] ,Receiver suspend of MDQ0~MDQ7,MDQS0,MXDQS0" "Enabled,Suspend" textline " " bitfld.long 0x0C 11. " R_SUSPD_DQ_[3] ,Driver suspend of MDQ24~MDQ31,MDM3,MDQS3,MXDQS3" "Enabled,Suspend" bitfld.long 0x0C 10. " [2] ,Driver suspend of MDQ16~MDQ23,MDM2,MDQS2,MXDQS2" "Enabled,Suspend" bitfld.long 0x0C 9. " [1] ,Driver suspend of MDQ8~MDQ15,MDM1,MDQS1,MXDQS1" "Enabled,Suspend" bitfld.long 0x0C 8. " [0] ,Driver suspend of MDQ0~MDQ7,MDM0,MDQS0,MXDQS0" "Enabled,Suspend" textline " " bitfld.long 0x0C 0. " R_SUSPD_CK ,Driver suspend of MCK,MXCK" "Enabled,Suspend" textline " " line.long 0x10 "REG_INIT0,This register sets the output timing for commands in DDR2 mode" bitfld.long 0x10 30.--31. " R_CMD_LAT_[15] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x10 28.--29. " [14] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x10 26.--27. " [13] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x10 24.--25. " [12] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x10 22.--23. " [11] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x10 20.--21. " [10] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x10 18.--19. " [9] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x10 16.--17. " [8] ,Please set 00 to this bit" "0,1,2,3" textline " " bitfld.long 0x10 14.--15. " [7] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x10 12.--13. " [6] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x10 10.--11. " [5] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x10 8.--9. " [4] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x10 6.--7. " [3] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x10 4.--5. " [2] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x10 2.--3. " [1] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x10 2.--3. " [0] ,Please set 00 to this bit" "0,1,2,3" line.long 0x14 "REG_INIT1,This register sets the output timing for commands in DDR2 mode" bitfld.long 0x14 14.--15. " R_CMD_LAT_[23] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x14 12.--13. " [22] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x14 10.--11. " [21] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x14 8.--9. " [20] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x14 6.--7. " [19] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x14 4.--5. " [18] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x14 2.--3. " [17] ,Please set 00 to this bit" "0,1,2,3" bitfld.long 0x14 0.--1. " [16] ,Please set 00 to this bit" "0,1,2,3" textline " " if (((per.l(ad:0x38400000+0x41C))&0x01)==0x01) group.long 0x41C++0x07 line.long 0x00 "REG_INIT2,This register can initialize PHY" bitfld.long 0x00 22.--23. " R_CDRV_DQ_[3] ,Driver impedance of MDQS3,MXDQS3,MDQ24~MDQ31,MDM3" "60 Ohm,48 Ohm,40 Ohm,34 Ohm" bitfld.long 0x00 20.--21. " [2] ,Driver impedance of MDQS2,MXDQS2,MDQ16~MDQ23,MDM2" "60 Ohm,48 Ohm,40 Ohm,34 Ohm" bitfld.long 0x00 18.--19. " [1] ,Driver impedance of MDQS1,MXDQS1,MDQ8~MDQ15,MDM1" "60 Ohm,48 Ohm,40 Ohm,34 Ohm" bitfld.long 0x00 16.--17. " [0] ,Driver impedance of MDQS0,MXDQS0,MDQ0~MDQ7,MDM0" "60 Ohm,48 Ohm,40 Ohm,34 Ohm" textline " " bitfld.long 0x00 10.--11. " R_CDRV_CMD ,Driver impedance of MA0~MA14,MBA0~MBA2,MXCS,MXCAS,MXRAS,MXWE,MODT,MCKE" "60 Ohm,48 Ohm,40 Ohm,34 Ohm" bitfld.long 0x00 8.--9. " R_CDRV_CK ,Driver impedance of MCK , MXCK" "60 Ohm,48 Ohm,40 Ohm,34 Ohm" bitfld.long 0x00 0. " R_DDRTYPE ,The operational mode of PHY" "DDR2 mode,DDR3 mode" line.long 0x04 "REG_INIT3,This register can initialize PHY" bitfld.long 0x04 24.--25. " R_RTE ,The RTE I/O cell pin is connected to this bit and can be controlled directly using it" ",120 Ohm,60 Ohm,40 Ohm" bitfld.long 0x04 21.--23. " R_PZQUPD_WIDTH ,Please set this bit according to the frequency of DRAM Clock as follows" ",,For 325MHz/650Mbps and under,For 350MHz/700Mbps and under,For 400MHz/800Mbps and under,For 450MHz/900Mbps and under,For 533MHz/1066Mbps and under," textline " " bitfld.long 0x04 19.--20. " R_PZQAVSET ,The value of r_pzqavset can be set using the clock frequency/transfer rate set by this bit" "0,1,2,3" bitfld.long 0x04 16. " R_PZQCLK_SEL ,Please set this bit according to the frequency of SDRAM Clock as follows" "400 MHz,533 MHz" textline " " bitfld.long 0x04 12.--14. " R_UDSET_[3] ,Please set 010 to this bit" "0,1,2,3,4,5,6,7" bitfld.long 0x04 8.--10. " R_UDSET_[2] ,Please set 010 to this bit" "0,1,2,3,4,5,6,7" bitfld.long 0x04 4.--6. " R_UDSET_[1] ,Please set 010 to this bit" "0,1,2,3,4,5,6,7" bitfld.long 0x04 0.--2. " R_UDSET_[0] ,Please set 010 to this bit" "0,1,2,3,4,5,6,7" else group.long 0x41C++0x07 line.long 0x00 "REG_INIT2,This register can initialize PHY" bitfld.long 0x00 22.--23. " R_CDRV_DQ_3 ,Driver impedance of MDQS3,MXDQS3,MDQ24~MDQ31,MDM3" "50 Ohm,40 Ohm,33.3 Ohm,28.6 Ohm" bitfld.long 0x00 20.--21. " R_CDRV_DQ_2 ,Driver impedance of MDQS2,MXDQS2,MDQ16~MDQ23,MDM2" "50 Ohm,40 Ohm,33.3 Ohm,28.6 Ohm" textline " " bitfld.long 0x00 18.--19. " R_CDRV_DQ_1 ,Driver impedance of MDQS1,MXDQS1,MDQ8~MDQ15,MDM1" "50 Ohm,40 Ohm,33.3 Ohm,28.6 Ohm" bitfld.long 0x00 16.--17. " R_CDRV_DQ_0 ,Driver impedance of MDQS0,MXDQS0,MDQ0~MDQ7,MDM0" "50 Ohm,40 Ohm,33.3 Ohm,28.6 Ohm" textline " " bitfld.long 0x00 10.--11. " R_CDRV_CMD ,Driver impedance of MA0~MA14,MBA0~MBA2,MXCS,MXCAS,MXRAS,MXWE,MODT,MCKE" "50 Ohm,40 Ohm,33.3 Ohm,28.6 Ohm" bitfld.long 0x00 8.--9. " R_CDRV_CK ,Driver impedance of MCK , MXCK" "50 Ohm,40 Ohm,33.3 Ohm,28.6 Ohm" textline " " bitfld.long 0x00 0. " R_DDRTYPE ,The operational mode of PHY" "DDR2 mode,DDR3 mode" line.long 0x04 "REG_INIT3,This register can initialize PHY" bitfld.long 0x04 24.--25. " R_RTE ,The RTE I/O cell pin is connected to this bit and can be controlled directly using it" ",100 Ohm,50 Ohm," sif (cpu()=="MB86R11F") bitfld.long 0x04 21.--23. " R_PZQUPD_WIDTH ,Please set this bit according to the frequency of DRAM Clock as follows" ",,For 325MHz/650Mbps and under,For 350MHz/700Mbps and under,For 400MHz/800Mbps and under,,," else bitfld.long 0x04 21.--23. " R_PZQUPD_WIDTH ,Please set this bit according to the frequency of DRAM Clock as follows" ",,For 325MHz/650Mbps and under,For 350MHz/700Mbps and under,For 400MHz/800Mbps and under,For 450MHz/900Mbps and under,For 533MHz/1066Mbps and under," endif textline " " bitfld.long 0x04 19.--20. " R_PZQAVSET ,The value of r_pzqavset can be set using the clock frequency/transfer rate set by this bit" "0,1,2,3" sif (cpu()=="MB86R11F") bitfld.long 0x04 16. " R_PZQCLK_SEL ,Please set this bit according to the frequency of SDRAM Clock as follows" "400 MHz,533 MHz" else bitfld.long 0x04 16. " R_PZQCLK_SEL ,Please set this bit according to the frequency of SDRAM Clock as follows" "400 MHz," endif textline " " bitfld.long 0x04 12.--14. " R_UDSET_[3] ,Please set 010 to this bit" "0,1,2,3,4,5,6,7" bitfld.long 0x04 8.--10. " R_UDSET_[2] ,Please set 010 to this bit" "0,1,2,3,4,5,6,7" bitfld.long 0x04 4.--6. " R_UDSET_[1] ,Please set 010 to this bit" "0,1,2,3,4,5,6,7" bitfld.long 0x04 0.--2. " R_UDSET_[0] ,Please set 010 to this bit" "0,1,2,3,4,5,6,7" endif textline " " group.long 0x424++0x23 line.long 0x00 "REG_INIT4,This register can initialize PHY" bitfld.long 0x00 24.--28. " R_X2CLKX_SFT_[3] ,Please set 01000 to this bit" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 16.--20. " [2] ,Please set 01000 to this bit" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 8.--12. " [1] ,Please set 01000 to this bit" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 0.--4. " [0] ,Please set 01000 to this bit" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x04 "REG_INIT5,This register can initialize PHY" bitfld.long 0x04 14.--15. " R_ODTON_END_[3] ,Please set this bit according to the frequency of DRAM" ",DDR2,DDR3," bitfld.long 0x04 12.--13. " [2] ,Please set this bit according to the frequency of DRAM" ",DDR2,DDR3," bitfld.long 0x04 10.--11. " [1] ,Please set this bit according to the frequency of DRAM" ",DDR2,DDR3," bitfld.long 0x04 8.--9. " [0] ,Please set this bit according to the frequency of DRAM" ",DDR2,DDR3," textline " " bitfld.long 0x04 6. " R_ODTON_STR_[3] ,Please set 0 to this bit" "0,1" bitfld.long 0x04 4. " [2] ,Please set 0 to this bit" "0,1" bitfld.long 0x04 2. " [1] ,Please set 0 to this bit" "0,1" bitfld.long 0x04 0. " [0] ,Please set 0 to this bit" "0,1" textline "" line.long 0x08 "REG_TDS0,This register can set each Delay value of PHY" bitfld.long 0x08 16.--20. " R_RXDQS_SFT_0 ,Offset[degree]" ",,,,,,,,45,50.625,56.25,61.875,67.5,73.125,78.75,84.375,90,95.625,101.25,106.875,112.5,118.125,123.75,129.375,,,,,,,," hexmask.long.byte 0x08 8.--15. 1. " R_TXDQ_SFT_0 ,TCK_TXDQ_offset[DRAM Clock]" sif (cpu()=="MB86R11F") bitfld.long 0x08 0.--4. " R_RDATA ,R_RDATA" ",,,,400MHz,..." else bitfld.long 0x08 0.--4. " R_RDATA ,R_RDATA" ",,,,400MHz,,,,533MHz,..." endif line.long 0x0C "REG_TDS1,This register can set each Delay value of PHY" bitfld.long 0x0C 16.--20. " R_RXDQS_SFT_1 ,Offset[degree]" ",,,,,,,,45,50.625,56.25,61.875,67.5,73.125,78.75,84.375,90,95.625,101.25,106.875,112.5,118.125,123.75,129.375,,,,,,,," hexmask.long.byte 0x0C 8.--15. 1. " R_TXDQ_SFT_1 ,TCK_TXDQ_offset[DRAM Clock]" sif (cpu()=="MB86R11F") bitfld.long 0x0C 0.--4. " R_RDATA ,R_RDATA" ",,,,400MHz,..." else bitfld.long 0x0C 0.--4. " R_RDATA ,R_RDATA" ",,,,400MHz,,,,533MHz,..." endif line.long 0x10 "REG_TDS2,This register can set each Delay value of PHY" bitfld.long 0x10 16.--20. " R_RXDQS_SFT_2 ,offset[degree]" ",,,,,,,,45,50.625,56.25,61.875,67.5,73.125,78.75,84.375,90,95.625,101.25,106.875,112.5,118.125,123.75,129.375,,,,,,,," hexmask.long.byte 0x10 8.--15. 1. " R_TXDQ_SFT_2 ,TCK_TXDQ_offset[DRAM Clock]" sif (cpu()=="MB86R11F") bitfld.long 0x10 0.--4. " R_RDATA ,R_RDATA" ",,,,400MHz,..." else bitfld.long 0x10 0.--4. " R_RDATA ,R_RDATA" ",,,,400MHz,,,,533MHz,..." endif textline " " line.long 0x14 "REG_TDS3,This register can set each Delay value of PHY" bitfld.long 0x14 16.--20. " R_RXDQS_SFT_3 ,Offset[degree]" ",,,,,,,,45,50.625,56.25,61.875,67.5,73.125,78.75,84.375,90,95.625,101.25,106.875,112.5,118.125,123.75,129.375,,,,,,,," hexmask.long.byte 0x14 8.--15. 1. " R_TXDQ_SFT_3 ,TCK_TXDQ_offset[DRAM Clock]" sif (cpu()=="MB86R11F") bitfld.long 0x14 0.--4. " R_RDATA ,R_RDATA" ",,,,400MHz,..." else bitfld.long 0x14 0.--4. " R_RDATA ,R_RDATA" ",,,,400MHz,,,,533MHz,..." endif textline " " line.long 0x18 "REG_TDS4,REG_TDS4" bitfld.long 0x18 24. " R_DSFT_LOAD_[3] ,R_DSFT_LOAD_3" "Not load,Load" bitfld.long 0x18 16. " [2] ,R_DSFT_LOAD_2" "Not load,Load" bitfld.long 0x18 8. " [1] ,R_DSFT_LOAD_1" "Not load,Load" bitfld.long 0x18 0. " [0] ,R_DSFT_LOAD_0" "Not load,Load" line.long 0x1C "REG_UP,Update can do the PZQ initial calibration result to this register" bitfld.long 0x1C 0. " R_PZQ_INIT_UPD ,Please set 0 to this bit according to the flow of PZQ initial calibration" "Update,Not update" width 0xb tree.end tree "HDMAC (AHB-DMA Controller)" base ad:0x04D00000 width 9. group.long 0x00++0x03 line.long 0x00 "DMACR,DMA Configuration Register" bitfld.long 0x00 31. " DE ,DMA enable" "Disabled,Enabled" rbitfld.long 0x00 30. " DS ,DMA stop" "Not stopped,Stopped" bitfld.long 0x00 28. " PR ,Priority rotation" "Fixed,Rotation" textline " " bitfld.long 0x00 24.--27. " DH ,DMA halt" "Not stopped,Stopped,Stopped,Stopped,Stopped,Stopped,Stopped,Stopped,Stopped,Stopped,Stopped,Stopped,Stopped,Stopped,Stopped,Stopped" if (((per.l(ad:0x04D00000+0x10))&0x00F00000)==(0x00||0x800000||0x900000)) group.long 0x10++0x03 line.long 0x00 "DMACA0,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" bitfld.long 0x00 16.--19. " BC ,Block count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" else group.long 0x10++0x03 line.long 0x00 "DMACA0,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" endif group.long (0x10+0x04)++0x0B line.long 0x00 "DMACB0,DMA Configuration B Register" bitfld.long 0x00 30.--31. " TT ,Transfer type" "2 cycles,?..." bitfld.long 0x00 28.--29. " MS ,Transfer mode" "Blocked,Burst mode,Demand mode,?..." bitfld.long 0x00 26.--27. " TW ,Transfer data width" "Byte,Half-word,Word,?..." textline " " bitfld.long 0x00 25. " FS ,Fixed source address" "Incremented,Fixed" bitfld.long 0x00 24. " FD ,Fixed destination address" "Incremented,Fixed" bitfld.long 0x00 23. " RC ,Reload count" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " RS ,Reload source" "Disabled,Enabled" bitfld.long 0x00 21. " RD ,Reload destination" "Disabled,Enabled" bitfld.long 0x00 20. " EI ,Error interrupt" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " CI ,Completion interrupt" "Disabled,Enabled" bitfld.long 0x00 16.--18. " SS ,Stop status" "Initial value,Address overflow,Transfer stop request,Source access error,Destination access error,Normal termination,,DMA pause" bitfld.long 0x00 12.--15. " SP ,Source protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 8.--11. " DP ,Destination protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x04 "DMACSA0,DMAC Source Address Register" line.long 0x08 "DMACDA0,DMAC Destination Address Register" if (((per.l(ad:0x04D00000+0x20))&0x00F00000)==(0x00||0x800000||0x900000)) group.long 0x20++0x03 line.long 0x00 "DMACA1,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" bitfld.long 0x00 16.--19. " BC ,Block count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" else group.long 0x20++0x03 line.long 0x00 "DMACA1,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" endif group.long (0x20+0x04)++0x0B line.long 0x00 "DMACB1,DMA Configuration B Register" bitfld.long 0x00 30.--31. " TT ,Transfer type" "2 cycles,?..." bitfld.long 0x00 28.--29. " MS ,Transfer mode" "Blocked,Burst mode,Demand mode,?..." bitfld.long 0x00 26.--27. " TW ,Transfer data width" "Byte,Half-word,Word,?..." textline " " bitfld.long 0x00 25. " FS ,Fixed source address" "Incremented,Fixed" bitfld.long 0x00 24. " FD ,Fixed destination address" "Incremented,Fixed" bitfld.long 0x00 23. " RC ,Reload count" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " RS ,Reload source" "Disabled,Enabled" bitfld.long 0x00 21. " RD ,Reload destination" "Disabled,Enabled" bitfld.long 0x00 20. " EI ,Error interrupt" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " CI ,Completion interrupt" "Disabled,Enabled" bitfld.long 0x00 16.--18. " SS ,Stop status" "Initial value,Address overflow,Transfer stop request,Source access error,Destination access error,Normal termination,,DMA pause" bitfld.long 0x00 12.--15. " SP ,Source protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 8.--11. " DP ,Destination protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x04 "DMACSA1,DMAC Source Address Register" line.long 0x08 "DMACDA1,DMAC Destination Address Register" if (((per.l(ad:0x04D00000+0x30))&0x00F00000)==(0x00||0x800000||0x900000)) group.long 0x30++0x03 line.long 0x00 "DMACA2,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" bitfld.long 0x00 16.--19. " BC ,Block count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" else group.long 0x30++0x03 line.long 0x00 "DMACA2,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" endif group.long (0x30+0x04)++0x0B line.long 0x00 "DMACB2,DMA Configuration B Register" bitfld.long 0x00 30.--31. " TT ,Transfer type" "2 cycles,?..." bitfld.long 0x00 28.--29. " MS ,Transfer mode" "Blocked,Burst mode,Demand mode,?..." bitfld.long 0x00 26.--27. " TW ,Transfer data width" "Byte,Half-word,Word,?..." textline " " bitfld.long 0x00 25. " FS ,Fixed source address" "Incremented,Fixed" bitfld.long 0x00 24. " FD ,Fixed destination address" "Incremented,Fixed" bitfld.long 0x00 23. " RC ,Reload count" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " RS ,Reload source" "Disabled,Enabled" bitfld.long 0x00 21. " RD ,Reload destination" "Disabled,Enabled" bitfld.long 0x00 20. " EI ,Error interrupt" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " CI ,Completion interrupt" "Disabled,Enabled" bitfld.long 0x00 16.--18. " SS ,Stop status" "Initial value,Address overflow,Transfer stop request,Source access error,Destination access error,Normal termination,,DMA pause" bitfld.long 0x00 12.--15. " SP ,Source protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 8.--11. " DP ,Destination protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x04 "DMACSA2,DMAC Source Address Register" line.long 0x08 "DMACDA2,DMAC Destination Address Register" if (((per.l(ad:0x04D00000+0x40))&0x00F00000)==(0x00||0x800000||0x900000)) group.long 0x40++0x03 line.long 0x00 "DMACA3,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" bitfld.long 0x00 16.--19. " BC ,Block count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" else group.long 0x40++0x03 line.long 0x00 "DMACA3,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" endif group.long (0x40+0x04)++0x0B line.long 0x00 "DMACB3,DMA Configuration B Register" bitfld.long 0x00 30.--31. " TT ,Transfer type" "2 cycles,?..." bitfld.long 0x00 28.--29. " MS ,Transfer mode" "Blocked,Burst mode,Demand mode,?..." bitfld.long 0x00 26.--27. " TW ,Transfer data width" "Byte,Half-word,Word,?..." textline " " bitfld.long 0x00 25. " FS ,Fixed source address" "Incremented,Fixed" bitfld.long 0x00 24. " FD ,Fixed destination address" "Incremented,Fixed" bitfld.long 0x00 23. " RC ,Reload count" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " RS ,Reload source" "Disabled,Enabled" bitfld.long 0x00 21. " RD ,Reload destination" "Disabled,Enabled" bitfld.long 0x00 20. " EI ,Error interrupt" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " CI ,Completion interrupt" "Disabled,Enabled" bitfld.long 0x00 16.--18. " SS ,Stop status" "Initial value,Address overflow,Transfer stop request,Source access error,Destination access error,Normal termination,,DMA pause" bitfld.long 0x00 12.--15. " SP ,Source protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 8.--11. " DP ,Destination protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x04 "DMACSA3,DMAC Source Address Register" line.long 0x08 "DMACDA3,DMAC Destination Address Register" if (((per.l(ad:0x04D00000+0x50))&0x00F00000)==(0x00||0x800000||0x900000)) group.long 0x50++0x03 line.long 0x00 "DMACA4,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" bitfld.long 0x00 16.--19. " BC ,Block count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" else group.long 0x50++0x03 line.long 0x00 "DMACA4,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" endif group.long (0x50+0x04)++0x0B line.long 0x00 "DMACB4,DMA Configuration B Register" bitfld.long 0x00 30.--31. " TT ,Transfer type" "2 cycles,?..." bitfld.long 0x00 28.--29. " MS ,Transfer mode" "Blocked,Burst mode,Demand mode,?..." bitfld.long 0x00 26.--27. " TW ,Transfer data width" "Byte,Half-word,Word,?..." textline " " bitfld.long 0x00 25. " FS ,Fixed source address" "Incremented,Fixed" bitfld.long 0x00 24. " FD ,Fixed destination address" "Incremented,Fixed" bitfld.long 0x00 23. " RC ,Reload count" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " RS ,Reload source" "Disabled,Enabled" bitfld.long 0x00 21. " RD ,Reload destination" "Disabled,Enabled" bitfld.long 0x00 20. " EI ,Error interrupt" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " CI ,Completion interrupt" "Disabled,Enabled" bitfld.long 0x00 16.--18. " SS ,Stop status" "Initial value,Address overflow,Transfer stop request,Source access error,Destination access error,Normal termination,,DMA pause" bitfld.long 0x00 12.--15. " SP ,Source protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 8.--11. " DP ,Destination protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x04 "DMACSA4,DMAC Source Address Register" line.long 0x08 "DMACDA4,DMAC Destination Address Register" if (((per.l(ad:0x04D00000+0x60))&0x00F00000)==(0x00||0x800000||0x900000)) group.long 0x60++0x03 line.long 0x00 "DMACA5,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" bitfld.long 0x00 16.--19. " BC ,Block count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" else group.long 0x60++0x03 line.long 0x00 "DMACA5,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" endif group.long (0x60+0x04)++0x0B line.long 0x00 "DMACB5,DMA Configuration B Register" bitfld.long 0x00 30.--31. " TT ,Transfer type" "2 cycles,?..." bitfld.long 0x00 28.--29. " MS ,Transfer mode" "Blocked,Burst mode,Demand mode,?..." bitfld.long 0x00 26.--27. " TW ,Transfer data width" "Byte,Half-word,Word,?..." textline " " bitfld.long 0x00 25. " FS ,Fixed source address" "Incremented,Fixed" bitfld.long 0x00 24. " FD ,Fixed destination address" "Incremented,Fixed" bitfld.long 0x00 23. " RC ,Reload count" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " RS ,Reload source" "Disabled,Enabled" bitfld.long 0x00 21. " RD ,Reload destination" "Disabled,Enabled" bitfld.long 0x00 20. " EI ,Error interrupt" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " CI ,Completion interrupt" "Disabled,Enabled" bitfld.long 0x00 16.--18. " SS ,Stop status" "Initial value,Address overflow,Transfer stop request,Source access error,Destination access error,Normal termination,,DMA pause" bitfld.long 0x00 12.--15. " SP ,Source protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 8.--11. " DP ,Destination protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x04 "DMACSA5,DMAC Source Address Register" line.long 0x08 "DMACDA5,DMAC Destination Address Register" if (((per.l(ad:0x04D00000+0x70))&0x00F00000)==(0x00||0x800000||0x900000)) group.long 0x70++0x03 line.long 0x00 "DMACA6,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" bitfld.long 0x00 16.--19. " BC ,Block count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" else group.long 0x70++0x03 line.long 0x00 "DMACA6,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" endif group.long (0x70+0x04)++0x0B line.long 0x00 "DMACB6,DMA Configuration B Register" bitfld.long 0x00 30.--31. " TT ,Transfer type" "2 cycles,?..." bitfld.long 0x00 28.--29. " MS ,Transfer mode" "Blocked,Burst mode,Demand mode,?..." bitfld.long 0x00 26.--27. " TW ,Transfer data width" "Byte,Half-word,Word,?..." textline " " bitfld.long 0x00 25. " FS ,Fixed source address" "Incremented,Fixed" bitfld.long 0x00 24. " FD ,Fixed destination address" "Incremented,Fixed" bitfld.long 0x00 23. " RC ,Reload count" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " RS ,Reload source" "Disabled,Enabled" bitfld.long 0x00 21. " RD ,Reload destination" "Disabled,Enabled" bitfld.long 0x00 20. " EI ,Error interrupt" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " CI ,Completion interrupt" "Disabled,Enabled" bitfld.long 0x00 16.--18. " SS ,Stop status" "Initial value,Address overflow,Transfer stop request,Source access error,Destination access error,Normal termination,,DMA pause" bitfld.long 0x00 12.--15. " SP ,Source protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 8.--11. " DP ,Destination protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x04 "DMACSA6,DMAC Source Address Register" line.long 0x08 "DMACDA6,DMAC Destination Address Register" if (((per.l(ad:0x04D00000+0x80))&0x00F00000)==(0x00||0x800000||0x900000)) group.long 0x80++0x03 line.long 0x00 "DMACA7,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" bitfld.long 0x00 16.--19. " BC ,Block count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" else group.long 0x80++0x03 line.long 0x00 "DMACA7,DMA Configuration A Register" bitfld.long 0x00 31. " EB ,Enable bit" "Disabled,Enabled" bitfld.long 0x00 30. " PB ,Pause bit" "Pause,Stopped" bitfld.long 0x00 29. " ST ,Software trigger" "Starts request,Software request" textline " " bitfld.long 0x00 24.--28. " IS ,Input select" "Software request,,,,,,,,,,,,,,DREQ H,DREQ L,IDREQ 0 H,IDREQ 1 H,IDREQ 2 H,IDREQ 3 H,IDREQ 4 H,IDREQ 5 H,IDREQ 6 H,IDREQ 7 H,IDREQ 8 H,IDREQ 9 H,IDREQ 10 H,IDREQ 11 H,IDREQ 12 H,IDREQ 13 H,IDREQ 14 H,IDREQ 15 H" bitfld.long 0x00 20.--23. " BT ,Beat type" "Normal,,,,,,,,Single(normal),INCR,WRAP4,INCR4,WRAP8,INCR8,WRAP16,INCR16" textline " " hexmask.long.word 0x00 0.--15. 1. " TC ,Transfer count" endif group.long (0x80+0x04)++0x0B line.long 0x00 "DMACB7,DMA Configuration B Register" bitfld.long 0x00 30.--31. " TT ,Transfer type" "2 cycles,?..." bitfld.long 0x00 28.--29. " MS ,Transfer mode" "Blocked,Burst mode,Demand mode,?..." bitfld.long 0x00 26.--27. " TW ,Transfer data width" "Byte,Half-word,Word,?..." textline " " bitfld.long 0x00 25. " FS ,Fixed source address" "Incremented,Fixed" bitfld.long 0x00 24. " FD ,Fixed destination address" "Incremented,Fixed" bitfld.long 0x00 23. " RC ,Reload count" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " RS ,Reload source" "Disabled,Enabled" bitfld.long 0x00 21. " RD ,Reload destination" "Disabled,Enabled" bitfld.long 0x00 20. " EI ,Error interrupt" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " CI ,Completion interrupt" "Disabled,Enabled" bitfld.long 0x00 16.--18. " SS ,Stop status" "Initial value,Address overflow,Transfer stop request,Source access error,Destination access error,Normal termination,,DMA pause" bitfld.long 0x00 12.--15. " SP ,Source protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 8.--11. " DP ,Destination protection" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x04 "DMACSA7,DMAC Source Address Register" line.long 0x08 "DMACDA7,DMAC Destination Address Register" width 0x0B tree.end tree "XDMAC (AXI-DMA Controller)" base ad:0xD0300000 width 10. group.long 0x00++0x03 line.long 0x00 "XDACS0_7,XDMAC All Channel Setting Register" bitfld.long 0x00 28. " XE ,XDMAC enable" "Disabled,Enabled" bitfld.long 0x00 24. " CP ,Channel priority" "Fixed,Rotated" bitfld.long 0x00 16. " XS ,XDMAC status" "Not active,Active" width 8. tree "Channel 0" group.long 0x10++0x17 line.long 0x00 "XDTBC0,XDMAC Transfer Byte Count Register" line.long 0x04 "XDSSA0,XDMAC Source Start Address Register" line.long 0x08 "XDDSA0,XDMAC Destination Start Address Register" line.long 0x0C "XDSAC0,XDMAC Source Access Configuration Register" bitfld.long 0x0C 16.--17. " SBS ,Source access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x0C 8.--11. " SBL ,Source access burst length" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16" bitfld.long 0x0C 2. " SAF ,Source address fix" "Not fixed,Fixed" textline " " bitfld.long 0x0C 0. " SRL ,Source address reload" "Disabled,Enabled" line.long 0x10 "XDDAC0,XDMAC Destination Access Configuration Register" bitfld.long 0x10 16.--17. " DBS ,Destination access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x10 8.--11. " DBL ,Destination access burst length" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x10 2. " DAF ,Destination address fix" "Not fixed,Fixed" textline " " bitfld.long 0x10 0. " DRL ,Destination address reload" "Disabled,Enabled" line.long 0x14 "XDDCC0,XDMAC Descriptor Chain Configuration Register" hexmask.long 0x14 4.--31. 1. " DCA ,Descriptor chain address" bitfld.long 0x14 0. " DCN ,Descriptor chain next valid" "Invalid,Valid" if (((per.l(ad:0xD0300000+0x10+0x14))&0x01)==0x01) if (((per.l(ad:0xD0300000+0x10+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0x10+0x18))&0xF00000)!=0x100000) group.long (0x10+0x18)++0x0B line.long 0x00 "XDDES0,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0x10+0x18)++0x0B line.long 0x00 "XDDES0,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif else if (((per.l(ad:0xD0300000+0x10+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0x10+0x18))&0xF00000)!=0x100000) group.long (0x10+0x18)++0x0B line.long 0x00 "XDDES0,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0x10+0x18)++0x0B line.long 0x00 "XDDES0,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif endif group.long (0x10+0x20)++0x07 line.long 0x00 "XDDPC0,XDMAC DMA Protection Control Register" bitfld.long 0x00 6. " SP[2] ,Source access protection level" "Data access,1" bitfld.long 0x00 5. " SP[1] ,Source access protection level" "Non-secure access,Secure access" bitfld.long 0x00 4. " SP[0] ,Source access protection level" "Normal access,Privileged access" textline " " bitfld.long 0x00 2. " DP[2] ,Destination access protection level" "Data access,1" bitfld.long 0x00 1. " DP[1] ,Destination access protection level" "Non-secure access,Secure access" bitfld.long 0x00 0. " DP[0] ,Destination access protection level" "Normal access,Privileged access" line.long 0x04 "XDDSD0,XDMAC DMA Status Display Register" rbitfld.long 0x04 16. " TS ,DMA transfer status" "Not running,Running" bitfld.long 0x04 0.--3. " IS ,Interrupt status" "Initial or clear,DMA stop by DSTP,DMA stop by disabling CE,,Source access error,Destination access error,Memory access error,,Normal end,?..." tree.end tree "Channel 1" group.long 0x40++0x17 line.long 0x00 "XDTBC1,XDMAC Transfer Byte Count Register" line.long 0x04 "XDSSA1,XDMAC Source Start Address Register" line.long 0x08 "XDDSA1,XDMAC Destination Start Address Register" line.long 0x0C "XDSAC1,XDMAC Source Access Configuration Register" bitfld.long 0x0C 16.--17. " SBS ,Source access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x0C 8.--11. " SBL ,Source access burst length" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16" bitfld.long 0x0C 2. " SAF ,Source address fix" "Not fixed,Fixed" textline " " bitfld.long 0x0C 0. " SRL ,Source address reload" "Disabled,Enabled" line.long 0x10 "XDDAC1,XDMAC Destination Access Configuration Register" bitfld.long 0x10 16.--17. " DBS ,Destination access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x10 8.--11. " DBL ,Destination access burst length" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x10 2. " DAF ,Destination address fix" "Not fixed,Fixed" textline " " bitfld.long 0x10 0. " DRL ,Destination address reload" "Disabled,Enabled" line.long 0x14 "XDDCC1,XDMAC Descriptor Chain Configuration Register" hexmask.long 0x14 4.--31. 1. " DCA ,Descriptor chain address" bitfld.long 0x14 0. " DCN ,Descriptor chain next valid" "Invalid,Valid" if (((per.l(ad:0xD0300000+0x40+0x14))&0x01)==0x01) if (((per.l(ad:0xD0300000+0x40+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0x40+0x18))&0xF00000)!=0x100000) group.long (0x40+0x18)++0x0B line.long 0x00 "XDDES1,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0x40+0x18)++0x0B line.long 0x00 "XDDES1,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif else if (((per.l(ad:0xD0300000+0x40+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0x40+0x18))&0xF00000)!=0x100000) group.long (0x40+0x18)++0x0B line.long 0x00 "XDDES1,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0x40+0x18)++0x0B line.long 0x00 "XDDES1,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif endif group.long (0x40+0x20)++0x07 line.long 0x00 "XDDPC1,XDMAC DMA Protection Control Register" bitfld.long 0x00 6. " SP[2] ,Source access protection level" "Data access,1" bitfld.long 0x00 5. " SP[1] ,Source access protection level" "Non-secure access,Secure access" bitfld.long 0x00 4. " SP[0] ,Source access protection level" "Normal access,Privileged access" textline " " bitfld.long 0x00 2. " DP[2] ,Destination access protection level" "Data access,1" bitfld.long 0x00 1. " DP[1] ,Destination access protection level" "Non-secure access,Secure access" bitfld.long 0x00 0. " DP[0] ,Destination access protection level" "Normal access,Privileged access" line.long 0x04 "XDDSD1,XDMAC DMA Status Display Register" rbitfld.long 0x04 16. " TS ,DMA transfer status" "Not running,Running" bitfld.long 0x04 0.--3. " IS ,Interrupt status" "Initial or clear,DMA stop by DSTP,DMA stop by disabling CE,,Source access error,Destination access error,Memory access error,,Normal end,?..." tree.end tree "Channel 2" group.long 0x70++0x17 line.long 0x00 "XDTBC2,XDMAC Transfer Byte Count Register" line.long 0x04 "XDSSA2,XDMAC Source Start Address Register" line.long 0x08 "XDDSA2,XDMAC Destination Start Address Register" line.long 0x0C "XDSAC2,XDMAC Source Access Configuration Register" bitfld.long 0x0C 16.--17. " SBS ,Source access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x0C 8.--11. " SBL ,Source access burst length" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16" bitfld.long 0x0C 2. " SAF ,Source address fix" "Not fixed,Fixed" textline " " bitfld.long 0x0C 0. " SRL ,Source address reload" "Disabled,Enabled" line.long 0x10 "XDDAC2,XDMAC Destination Access Configuration Register" bitfld.long 0x10 16.--17. " DBS ,Destination access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x10 8.--11. " DBL ,Destination access burst length" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x10 2. " DAF ,Destination address fix" "Not fixed,Fixed" textline " " bitfld.long 0x10 0. " DRL ,Destination address reload" "Disabled,Enabled" line.long 0x14 "XDDCC2,XDMAC Descriptor Chain Configuration Register" hexmask.long 0x14 4.--31. 1. " DCA ,Descriptor chain address" bitfld.long 0x14 0. " DCN ,Descriptor chain next valid" "Invalid,Valid" if (((per.l(ad:0xD0300000+0x70+0x14))&0x01)==0x01) if (((per.l(ad:0xD0300000+0x70+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0x70+0x18))&0xF00000)!=0x100000) group.long (0x70+0x18)++0x0B line.long 0x00 "XDDES2,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0x70+0x18)++0x0B line.long 0x00 "XDDES2,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif else if (((per.l(ad:0xD0300000+0x70+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0x70+0x18))&0xF00000)!=0x100000) group.long (0x70+0x18)++0x0B line.long 0x00 "XDDES2,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0x70+0x18)++0x0B line.long 0x00 "XDDES2,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif endif group.long (0x70+0x20)++0x07 line.long 0x00 "XDDPC2,XDMAC DMA Protection Control Register" bitfld.long 0x00 6. " SP[2] ,Source access protection level" "Data access,1" bitfld.long 0x00 5. " SP[1] ,Source access protection level" "Non-secure access,Secure access" bitfld.long 0x00 4. " SP[0] ,Source access protection level" "Normal access,Privileged access" textline " " bitfld.long 0x00 2. " DP[2] ,Destination access protection level" "Data access,1" bitfld.long 0x00 1. " DP[1] ,Destination access protection level" "Non-secure access,Secure access" bitfld.long 0x00 0. " DP[0] ,Destination access protection level" "Normal access,Privileged access" line.long 0x04 "XDDSD2,XDMAC DMA Status Display Register" rbitfld.long 0x04 16. " TS ,DMA transfer status" "Not running,Running" bitfld.long 0x04 0.--3. " IS ,Interrupt status" "Initial or clear,DMA stop by DSTP,DMA stop by disabling CE,,Source access error,Destination access error,Memory access error,,Normal end,?..." tree.end tree "Channel 3" group.long 0xA0++0x17 line.long 0x00 "XDTBC3,XDMAC Transfer Byte Count Register" line.long 0x04 "XDSSA3,XDMAC Source Start Address Register" line.long 0x08 "XDDSA3,XDMAC Destination Start Address Register" line.long 0x0C "XDSAC3,XDMAC Source Access Configuration Register" bitfld.long 0x0C 16.--17. " SBS ,Source access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x0C 8.--11. " SBL ,Source access burst length" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16" bitfld.long 0x0C 2. " SAF ,Source address fix" "Not fixed,Fixed" textline " " bitfld.long 0x0C 0. " SRL ,Source address reload" "Disabled,Enabled" line.long 0x10 "XDDAC3,XDMAC Destination Access Configuration Register" bitfld.long 0x10 16.--17. " DBS ,Destination access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x10 8.--11. " DBL ,Destination access burst length" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x10 2. " DAF ,Destination address fix" "Not fixed,Fixed" textline " " bitfld.long 0x10 0. " DRL ,Destination address reload" "Disabled,Enabled" line.long 0x14 "XDDCC3,XDMAC Descriptor Chain Configuration Register" hexmask.long 0x14 4.--31. 1. " DCA ,Descriptor chain address" bitfld.long 0x14 0. " DCN ,Descriptor chain next valid" "Invalid,Valid" if (((per.l(ad:0xD0300000+0xA0+0x14))&0x01)==0x01) if (((per.l(ad:0xD0300000+0xA0+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0xA0+0x18))&0xF00000)!=0x100000) group.long (0xA0+0x18)++0x0B line.long 0x00 "XDDES3,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0xA0+0x18)++0x0B line.long 0x00 "XDDES3,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif else if (((per.l(ad:0xD0300000+0xA0+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0xA0+0x18))&0xF00000)!=0x100000) group.long (0xA0+0x18)++0x0B line.long 0x00 "XDDES3,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0xA0+0x18)++0x0B line.long 0x00 "XDDES3,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif endif group.long (0xA0+0x20)++0x07 line.long 0x00 "XDDPC3,XDMAC DMA Protection Control Register" bitfld.long 0x00 6. " SP[2] ,Source access protection level" "Data access,1" bitfld.long 0x00 5. " SP[1] ,Source access protection level" "Non-secure access,Secure access" bitfld.long 0x00 4. " SP[0] ,Source access protection level" "Normal access,Privileged access" textline " " bitfld.long 0x00 2. " DP[2] ,Destination access protection level" "Data access,1" bitfld.long 0x00 1. " DP[1] ,Destination access protection level" "Non-secure access,Secure access" bitfld.long 0x00 0. " DP[0] ,Destination access protection level" "Normal access,Privileged access" line.long 0x04 "XDDSD3,XDMAC DMA Status Display Register" rbitfld.long 0x04 16. " TS ,DMA transfer status" "Not running,Running" bitfld.long 0x04 0.--3. " IS ,Interrupt status" "Initial or clear,DMA stop by DSTP,DMA stop by disabling CE,,Source access error,Destination access error,Memory access error,,Normal end,?..." tree.end tree "Channel 4" group.long 0xD0++0x17 line.long 0x00 "XDTBC4,XDMAC Transfer Byte Count Register" line.long 0x04 "XDSSA4,XDMAC Source Start Address Register" line.long 0x08 "XDDSA4,XDMAC Destination Start Address Register" line.long 0x0C "XDSAC4,XDMAC Source Access Configuration Register" bitfld.long 0x0C 16.--17. " SBS ,Source access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x0C 8.--11. " SBL ,Source access burst length" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16" bitfld.long 0x0C 2. " SAF ,Source address fix" "Not fixed,Fixed" textline " " bitfld.long 0x0C 0. " SRL ,Source address reload" "Disabled,Enabled" line.long 0x10 "XDDAC4,XDMAC Destination Access Configuration Register" bitfld.long 0x10 16.--17. " DBS ,Destination access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x10 8.--11. " DBL ,Destination access burst length" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x10 2. " DAF ,Destination address fix" "Not fixed,Fixed" textline " " bitfld.long 0x10 0. " DRL ,Destination address reload" "Disabled,Enabled" line.long 0x14 "XDDCC4,XDMAC Descriptor Chain Configuration Register" hexmask.long 0x14 4.--31. 1. " DCA ,Descriptor chain address" bitfld.long 0x14 0. " DCN ,Descriptor chain next valid" "Invalid,Valid" if (((per.l(ad:0xD0300000+0xD0+0x14))&0x01)==0x01) if (((per.l(ad:0xD0300000+0xD0+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0xD0+0x18))&0xF00000)!=0x100000) group.long (0xD0+0x18)++0x0B line.long 0x00 "XDDES4,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0xD0+0x18)++0x0B line.long 0x00 "XDDES4,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif else if (((per.l(ad:0xD0300000+0xD0+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0xD0+0x18))&0xF00000)!=0x100000) group.long (0xD0+0x18)++0x0B line.long 0x00 "XDDES4,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0xD0+0x18)++0x0B line.long 0x00 "XDDES4,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif endif group.long (0xD0+0x20)++0x07 line.long 0x00 "XDDPC4,XDMAC DMA Protection Control Register" bitfld.long 0x00 6. " SP[2] ,Source access protection level" "Data access,1" bitfld.long 0x00 5. " SP[1] ,Source access protection level" "Non-secure access,Secure access" bitfld.long 0x00 4. " SP[0] ,Source access protection level" "Normal access,Privileged access" textline " " bitfld.long 0x00 2. " DP[2] ,Destination access protection level" "Data access,1" bitfld.long 0x00 1. " DP[1] ,Destination access protection level" "Non-secure access,Secure access" bitfld.long 0x00 0. " DP[0] ,Destination access protection level" "Normal access,Privileged access" line.long 0x04 "XDDSD4,XDMAC DMA Status Display Register" rbitfld.long 0x04 16. " TS ,DMA transfer status" "Not running,Running" bitfld.long 0x04 0.--3. " IS ,Interrupt status" "Initial or clear,DMA stop by DSTP,DMA stop by disabling CE,,Source access error,Destination access error,Memory access error,,Normal end,?..." tree.end tree "Channel 5" group.long 0x100++0x17 line.long 0x00 "XDTBC5,XDMAC Transfer Byte Count Register" line.long 0x04 "XDSSA5,XDMAC Source Start Address Register" line.long 0x08 "XDDSA5,XDMAC Destination Start Address Register" line.long 0x0C "XDSAC5,XDMAC Source Access Configuration Register" bitfld.long 0x0C 16.--17. " SBS ,Source access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x0C 8.--11. " SBL ,Source access burst length" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16" bitfld.long 0x0C 2. " SAF ,Source address fix" "Not fixed,Fixed" textline " " bitfld.long 0x0C 0. " SRL ,Source address reload" "Disabled,Enabled" line.long 0x10 "XDDAC5,XDMAC Destination Access Configuration Register" bitfld.long 0x10 16.--17. " DBS ,Destination access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x10 8.--11. " DBL ,Destination access burst length" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x10 2. " DAF ,Destination address fix" "Not fixed,Fixed" textline " " bitfld.long 0x10 0. " DRL ,Destination address reload" "Disabled,Enabled" line.long 0x14 "XDDCC5,XDMAC Descriptor Chain Configuration Register" hexmask.long 0x14 4.--31. 1. " DCA ,Descriptor chain address" bitfld.long 0x14 0. " DCN ,Descriptor chain next valid" "Invalid,Valid" if (((per.l(ad:0xD0300000+0x100+0x14))&0x01)==0x01) if (((per.l(ad:0xD0300000+0x100+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0x100+0x18))&0xF00000)!=0x100000) group.long (0x100+0x18)++0x0B line.long 0x00 "XDDES5,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0x100+0x18)++0x0B line.long 0x00 "XDDES5,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif else if (((per.l(ad:0xD0300000+0x100+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0x100+0x18))&0xF00000)!=0x100000) group.long (0x100+0x18)++0x0B line.long 0x00 "XDDES5,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0x100+0x18)++0x0B line.long 0x00 "XDDES5,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif endif group.long (0x100+0x20)++0x07 line.long 0x00 "XDDPC5,XDMAC DMA Protection Control Register" bitfld.long 0x00 6. " SP[2] ,Source access protection level" "Data access,1" bitfld.long 0x00 5. " SP[1] ,Source access protection level" "Non-secure access,Secure access" bitfld.long 0x00 4. " SP[0] ,Source access protection level" "Normal access,Privileged access" textline " " bitfld.long 0x00 2. " DP[2] ,Destination access protection level" "Data access,1" bitfld.long 0x00 1. " DP[1] ,Destination access protection level" "Non-secure access,Secure access" bitfld.long 0x00 0. " DP[0] ,Destination access protection level" "Normal access,Privileged access" line.long 0x04 "XDDSD5,XDMAC DMA Status Display Register" rbitfld.long 0x04 16. " TS ,DMA transfer status" "Not running,Running" bitfld.long 0x04 0.--3. " IS ,Interrupt status" "Initial or clear,DMA stop by DSTP,DMA stop by disabling CE,,Source access error,Destination access error,Memory access error,,Normal end,?..." tree.end tree "Channel 6" group.long 0x130++0x17 line.long 0x00 "XDTBC6,XDMAC Transfer Byte Count Register" line.long 0x04 "XDSSA6,XDMAC Source Start Address Register" line.long 0x08 "XDDSA6,XDMAC Destination Start Address Register" line.long 0x0C "XDSAC6,XDMAC Source Access Configuration Register" bitfld.long 0x0C 16.--17. " SBS ,Source access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x0C 8.--11. " SBL ,Source access burst length" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16" bitfld.long 0x0C 2. " SAF ,Source address fix" "Not fixed,Fixed" textline " " bitfld.long 0x0C 0. " SRL ,Source address reload" "Disabled,Enabled" line.long 0x10 "XDDAC6,XDMAC Destination Access Configuration Register" bitfld.long 0x10 16.--17. " DBS ,Destination access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x10 8.--11. " DBL ,Destination access burst length" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x10 2. " DAF ,Destination address fix" "Not fixed,Fixed" textline " " bitfld.long 0x10 0. " DRL ,Destination address reload" "Disabled,Enabled" line.long 0x14 "XDDCC6,XDMAC Descriptor Chain Configuration Register" hexmask.long 0x14 4.--31. 1. " DCA ,Descriptor chain address" bitfld.long 0x14 0. " DCN ,Descriptor chain next valid" "Invalid,Valid" if (((per.l(ad:0xD0300000+0x130+0x14))&0x01)==0x01) if (((per.l(ad:0xD0300000+0x130+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0x130+0x18))&0xF00000)!=0x100000) group.long (0x130+0x18)++0x0B line.long 0x00 "XDDES6,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0x130+0x18)++0x0B line.long 0x00 "XDDES6,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif else if (((per.l(ad:0xD0300000+0x130+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0x130+0x18))&0xF00000)!=0x100000) group.long (0x130+0x18)++0x0B line.long 0x00 "XDDES6,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0x130+0x18)++0x0B line.long 0x00 "XDDES6,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif endif group.long (0x130+0x20)++0x07 line.long 0x00 "XDDPC6,XDMAC DMA Protection Control Register" bitfld.long 0x00 6. " SP[2] ,Source access protection level" "Data access,1" bitfld.long 0x00 5. " SP[1] ,Source access protection level" "Non-secure access,Secure access" bitfld.long 0x00 4. " SP[0] ,Source access protection level" "Normal access,Privileged access" textline " " bitfld.long 0x00 2. " DP[2] ,Destination access protection level" "Data access,1" bitfld.long 0x00 1. " DP[1] ,Destination access protection level" "Non-secure access,Secure access" bitfld.long 0x00 0. " DP[0] ,Destination access protection level" "Normal access,Privileged access" line.long 0x04 "XDDSD6,XDMAC DMA Status Display Register" rbitfld.long 0x04 16. " TS ,DMA transfer status" "Not running,Running" bitfld.long 0x04 0.--3. " IS ,Interrupt status" "Initial or clear,DMA stop by DSTP,DMA stop by disabling CE,,Source access error,Destination access error,Memory access error,,Normal end,?..." tree.end tree "Channel 7" group.long 0x160++0x17 line.long 0x00 "XDTBC7,XDMAC Transfer Byte Count Register" line.long 0x04 "XDSSA7,XDMAC Source Start Address Register" line.long 0x08 "XDDSA7,XDMAC Destination Start Address Register" line.long 0x0C "XDSAC7,XDMAC Source Access Configuration Register" bitfld.long 0x0C 16.--17. " SBS ,Source access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x0C 8.--11. " SBL ,Source access burst length" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16" bitfld.long 0x0C 2. " SAF ,Source address fix" "Not fixed,Fixed" textline " " bitfld.long 0x0C 0. " SRL ,Source address reload" "Disabled,Enabled" line.long 0x10 "XDDAC7,XDMAC Destination Access Configuration Register" bitfld.long 0x10 16.--17. " DBS ,Destination access burst size" "Byte,Half word,Word,Double word" bitfld.long 0x10 8.--11. " DBL ,Destination access burst length" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x10 2. " DAF ,Destination address fix" "Not fixed,Fixed" textline " " bitfld.long 0x10 0. " DRL ,Destination address reload" "Disabled,Enabled" line.long 0x14 "XDDCC7,XDMAC Descriptor Chain Configuration Register" hexmask.long 0x14 4.--31. 1. " DCA ,Descriptor chain address" bitfld.long 0x14 0. " DCN ,Descriptor chain next valid" "Invalid,Valid" if (((per.l(ad:0xD0300000+0x160+0x14))&0x01)==0x01) if (((per.l(ad:0xD0300000+0x160+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0x160+0x18))&0xF00000)!=0x100000) group.long (0x160+0x18)++0x0B line.long 0x00 "XDDES7,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0x160+0x18)++0x0B line.long 0x00 "XDDES7,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif else if (((per.l(ad:0xD0300000+0x160+0x18))&0xF00000)!=0x00)&&(((per.l(ad:0xD0300000+0x160+0x18))&0xF00000)!=0x100000) group.long (0x160+0x18)++0x0B line.long 0x00 "XDDES7,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " AT ,DACK assert timing" "Source slave,Destination slave" bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" else group.long (0x160+0x18)++0x0B line.long 0x00 "XDDES7,XDMAC DMA Enable Setting Register" bitfld.long 0x00 28. " CE ,Channel enable" "Disabled,Enabled" bitfld.long 0x00 24. " SE ,Software enable" "Disabled,Enabled" bitfld.long 0x00 20.--23. " TF ,Transfer factor" "None,Software,DREQ[0],DREQ[1],DREQ[2],DREQ[3],DREQ[4],DREQ[5],DREQ[6],DREQ[7],DREQ[8],DREQ[9],DREQ[10],DREQ[11],DREQ[12],DREQ[13]" textline " " bitfld.long 0x00 15. " SA ,Serial access" "Disabled,Enabled" bitfld.long 0x00 12. " BT ,Block transfer" "Disabled,Enabled" bitfld.long 0x00 8. " BR ,Transfer byte count reload" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " EI ,Error interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " TI ,Termination interrupt" "Disabled,Enabled" endif endif group.long (0x160+0x20)++0x07 line.long 0x00 "XDDPC7,XDMAC DMA Protection Control Register" bitfld.long 0x00 6. " SP[2] ,Source access protection level" "Data access,1" bitfld.long 0x00 5. " SP[1] ,Source access protection level" "Non-secure access,Secure access" bitfld.long 0x00 4. " SP[0] ,Source access protection level" "Normal access,Privileged access" textline " " bitfld.long 0x00 2. " DP[2] ,Destination access protection level" "Data access,1" bitfld.long 0x00 1. " DP[1] ,Destination access protection level" "Non-secure access,Secure access" bitfld.long 0x00 0. " DP[0] ,Destination access protection level" "Normal access,Privileged access" line.long 0x04 "XDDSD7,XDMAC DMA Status Display Register" rbitfld.long 0x04 16. " TS ,DMA transfer status" "Not running,Running" bitfld.long 0x04 0.--3. " IS ,Interrupt status" "Initial or clear,DMA stop by DSTP,DMA stop by disabling CE,,Source access error,Destination access error,Memory access error,,Normal end,?..." tree.end width 0x0B tree.end tree "GPIO (General Purpose Input/Output)" base ad:0x3B300000 width 7. group.long 0x0++0x03 line.long 0x00 "PDR0,Port Data Register 0" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x4++0x03 line.long 0x00 "PDR1,Port Data Register 1" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x8++0x03 line.long 0x00 "PDR2,Port Data Register 2" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0xC++0x03 line.long 0x00 "PDR3,Port Data Register 3" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x10++0x03 line.long 0x00 "PDR4,Port Data Register 4" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x14++0x03 line.long 0x00 "PDR5,Port Data Register 5" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x18++0x03 line.long 0x00 "PDR6,Port Data Register 6" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x1C++0x03 line.long 0x00 "PDR7,Port Data Register 7" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x20++0x03 line.long 0x00 "PDR8,Port Data Register 8" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x24++0x03 line.long 0x00 "PDR9,Port Data Register 9" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x28++0x03 line.long 0x00 "PDR10,Port Data Register 10" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x2C++0x03 line.long 0x00 "PDR11,Port Data Register 11" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x30++0x03 line.long 0x00 "PDR12,Port Data Register 12" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x34++0x03 line.long 0x00 "PDR13,Port Data Register 13" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x38++0x03 line.long 0x00 "PDR14,Port Data Register 14" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x3C++0x03 line.long 0x00 "PDR15,Port Data Register 15" hexmask.long.byte 0x00 0.--7. 1. " PDR ,8bit data register" group.long 0x40++0x03 line.long 0x00 "DDR0,Data Direction Register 0" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x44++0x03 line.long 0x00 "DDR1,Data Direction Register 1" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x48++0x03 line.long 0x00 "DDR2,Data Direction Register 2" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x4C++0x03 line.long 0x00 "DDR3,Data Direction Register 3" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x50++0x03 line.long 0x00 "DDR4,Data Direction Register 4" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x54++0x03 line.long 0x00 "DDR5,Data Direction Register 5" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x58++0x03 line.long 0x00 "DDR6,Data Direction Register 6" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x5C++0x03 line.long 0x00 "DDR7,Data Direction Register 7" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x60++0x03 line.long 0x00 "DDR8,Data Direction Register 8" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x64++0x03 line.long 0x00 "DDR9,Data Direction Register 9" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x68++0x03 line.long 0x00 "DDR10,Data Direction Register 10" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x6C++0x03 line.long 0x00 "DDR11,Data Direction Register 11" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x70++0x03 line.long 0x00 "DDR12,Data Direction Register 12" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x74++0x03 line.long 0x00 "DDR13,Data Direction Register 13" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x78++0x03 line.long 0x00 "DDR14,Data Direction Register 14" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" group.long 0x7C++0x03 line.long 0x00 "DDR15,Data Direction Register 15" bitfld.long 0x00 7. " DDR_[7] ,Direction control register" "Input,Output" bitfld.long 0x00 6. " [6] ,Direction control register" "Input,Output" bitfld.long 0x00 5. " [5] ,Direction control register" "Input,Output" bitfld.long 0x00 4. " [4] ,Direction control register" "Input,Output" bitfld.long 0x00 3. " [3] ,Direction control register" "Input,Output" bitfld.long 0x00 2. " [2] ,Direction control register" "Input,Output" bitfld.long 0x00 1. " [1] ,Direction control register" "Input,Output" bitfld.long 0x00 0. " [0] ,Direction control register" "Input,Output" width 0xb tree.end tree "PWM (Pulse Width Modulator)" tree "PWM 0" base ad:0x3C200000 width 10. group.long (0x00+0x00)++0x17 line.long 0x00 "BCR0,PWM Base Clock Register" hexmask.long.word 0x00 0.--15. 1. " BCR ,Cycle furation of PWM base clock to APB clock cycles" line.long 0x04 "TPR0,PWM Total Pulse Register" hexmask.long.word 0x04 0.--15. 1. " TPR ,Total pulse" line.long 0x08 "PR0,PWM Phase Ratio Register" hexmask.long.word 0x08 0.--15. 1. " PR ,Phase ratio" line.long 0x0C "DR0,PWM Duty Ratio Register" hexmask.long.word 0x0C 0.--15. 1. " DR ,Duty ratio" line.long 0x10 "CR0,PWM Condition Register" bitfld.long 0x10 3. " ONESHOT ,Single/continuous set register of PWM output pulse" "Continuous,Single" bitfld.long 0x10 2. " EXEDGE ,Negative/positive edge set register of external trigger start pulse" "Negative edge,Positive edge" textline " " bitfld.long 0x10 1. " EXTRG ,ON/OFF setting register of external trigger" "Off,On" bitfld.long 0x10 0. " POL ,Polarity setting register of PWM output pulse" "Negative pulse,Positive pulse" line.long 0x14 "SR0,PWM Start Register" bitfld.long 0x14 1. " SYNC ,Synchronization and setting registers of two channels" "Off,On" bitfld.long 0x14 0. " START ,PWM output start setting register" "Stopped,Started" rgroup.long (0x00+0x18)++0x03 line.long 0x00 "CCR0,PWM Current Count Register" hexmask.long.word 0x00 0.--15. 1. " CCR ,PWM base clock counter" group.long (0x00+0x1C)++0x03 line.long 0x00 "IR0,PWM Interrupt Register" bitfld.long 0x00 8.--9. " INTREP ,PWM interrupt output condition setting register" "NO,DONE,TRGDEC,DONE+TRGDEC" bitfld.long 0x00 1. " TRGDEC ,Trigger edge detection register" "Not detected,Detected" textline " " bitfld.long 0x00 0. " DONE ,Completion watch register of one PWM pulse cycle" "Not completed,Completed" textline "" group.long (0x80+0x00)++0x17 line.long 0x00 "BCR1,PWM Base Clock Register" hexmask.long.word 0x00 0.--15. 1. " BCR ,Cycle furation of PWM base clock to APB clock cycles" line.long 0x04 "TPR1,PWM Total Pulse Register" hexmask.long.word 0x04 0.--15. 1. " TPR ,Total pulse" line.long 0x08 "PR1,PWM Phase Ratio Register" hexmask.long.word 0x08 0.--15. 1. " PR ,Phase ratio" line.long 0x0C "DR1,PWM Duty Ratio Register" hexmask.long.word 0x0C 0.--15. 1. " DR ,Duty ratio" line.long 0x10 "CR1,PWM Condition Register" bitfld.long 0x10 3. " ONESHOT ,Single/continuous set register of PWM output pulse" "Continuous,Single" bitfld.long 0x10 2. " EXEDGE ,Negative/positive edge set register of external trigger start pulse" "Negative edge,Positive edge" textline " " bitfld.long 0x10 1. " EXTRG ,ON/OFF setting register of external trigger" "Off,On" bitfld.long 0x10 0. " POL ,Polarity setting register of PWM output pulse" "Negative pulse,Positive pulse" line.long 0x14 "SR1,PWM Start Register" bitfld.long 0x14 1. " SYNC ,Synchronization and setting registers of two channels" "Off,On" bitfld.long 0x14 0. " START ,PWM output start setting register" "Stopped,Started" rgroup.long (0x80+0x18)++0x03 line.long 0x00 "CCR1,PWM Current Count Register" hexmask.long.word 0x00 0.--15. 1. " CCR ,PWM base clock counter" group.long (0x80+0x1C)++0x03 line.long 0x00 "IR1,PWM Interrupt Register" bitfld.long 0x00 8.--9. " INTREP ,PWM interrupt output condition setting register" "NO,DONE,TRGDEC,DONE+TRGDEC" bitfld.long 0x00 1. " TRGDEC ,Trigger edge detection register" "Not detected,Detected" textline " " bitfld.long 0x00 0. " DONE ,Completion watch register of one PWM pulse cycle" "Not completed,Completed" textline "" group.long (0x100+0x00)++0x17 line.long 0x00 "BCR2,PWM Base Clock Register" hexmask.long.word 0x00 0.--15. 1. " BCR ,Cycle furation of PWM base clock to APB clock cycles" line.long 0x04 "TPR2,PWM Total Pulse Register" hexmask.long.word 0x04 0.--15. 1. " TPR ,Total pulse" line.long 0x08 "PR2,PWM Phase Ratio Register" hexmask.long.word 0x08 0.--15. 1. " PR ,Phase ratio" line.long 0x0C "DR2,PWM Duty Ratio Register" hexmask.long.word 0x0C 0.--15. 1. " DR ,Duty ratio" line.long 0x10 "CR2,PWM Condition Register" bitfld.long 0x10 3. " ONESHOT ,Single/continuous set register of PWM output pulse" "Continuous,Single" bitfld.long 0x10 2. " EXEDGE ,Negative/positive edge set register of external trigger start pulse" "Negative edge,Positive edge" textline " " bitfld.long 0x10 1. " EXTRG ,ON/OFF setting register of external trigger" "Off,On" bitfld.long 0x10 0. " POL ,Polarity setting register of PWM output pulse" "Negative pulse,Positive pulse" line.long 0x14 "SR2,PWM Start Register" bitfld.long 0x14 1. " SYNC ,Synchronization and setting registers of two channels" "Off,On" bitfld.long 0x14 0. " START ,PWM output start setting register" "Stopped,Started" rgroup.long (0x100+0x18)++0x03 line.long 0x00 "CCR2,PWM Current Count Register" hexmask.long.word 0x00 0.--15. 1. " CCR ,PWM base clock counter" group.long (0x100+0x1C)++0x03 line.long 0x00 "IR2,PWM Interrupt Register" bitfld.long 0x00 8.--9. " INTREP ,PWM interrupt output condition setting register" "NO,DONE,TRGDEC,DONE+TRGDEC" bitfld.long 0x00 1. " TRGDEC ,Trigger edge detection register" "Not detected,Detected" textline " " bitfld.long 0x00 0. " DONE ,Completion watch register of one PWM pulse cycle" "Not completed,Completed" textline "" group.long (0x180+0x00)++0x17 line.long 0x00 "BCR3,PWM Base Clock Register" hexmask.long.word 0x00 0.--15. 1. " BCR ,Cycle furation of PWM base clock to APB clock cycles" line.long 0x04 "TPR3,PWM Total Pulse Register" hexmask.long.word 0x04 0.--15. 1. " TPR ,Total pulse" line.long 0x08 "PR3,PWM Phase Ratio Register" hexmask.long.word 0x08 0.--15. 1. " PR ,Phase ratio" line.long 0x0C "DR3,PWM Duty Ratio Register" hexmask.long.word 0x0C 0.--15. 1. " DR ,Duty ratio" line.long 0x10 "CR3,PWM Condition Register" bitfld.long 0x10 3. " ONESHOT ,Single/continuous set register of PWM output pulse" "Continuous,Single" bitfld.long 0x10 2. " EXEDGE ,Negative/positive edge set register of external trigger start pulse" "Negative edge,Positive edge" textline " " bitfld.long 0x10 1. " EXTRG ,ON/OFF setting register of external trigger" "Off,On" bitfld.long 0x10 0. " POL ,Polarity setting register of PWM output pulse" "Negative pulse,Positive pulse" line.long 0x14 "SR3,PWM Start Register" bitfld.long 0x14 1. " SYNC ,Synchronization and setting registers of two channels" "Off,On" bitfld.long 0x14 0. " START ,PWM output start setting register" "Stopped,Started" rgroup.long (0x180+0x18)++0x03 line.long 0x00 "CCR3,PWM Current Count Register" hexmask.long.word 0x00 0.--15. 1. " CCR ,PWM base clock counter" group.long (0x180+0x1C)++0x03 line.long 0x00 "IR3,PWM Interrupt Register" bitfld.long 0x00 8.--9. " INTREP ,PWM interrupt output condition setting register" "NO,DONE,TRGDEC,DONE+TRGDEC" bitfld.long 0x00 1. " TRGDEC ,Trigger edge detection register" "Not detected,Detected" textline " " bitfld.long 0x00 0. " DONE ,Completion watch register of one PWM pulse cycle" "Not completed,Completed" textline "" width 0x0B tree.end tree "PWM 1" base ad:0x3C210000 width 10. group.long (0x00+0x00)++0x17 line.long 0x00 "BCR1,PWM Base Clock Register" hexmask.long.word 0x00 0.--15. 1. " BCR ,Cycle furation of PWM base clock to APB clock cycles" line.long 0x04 "TPR1,PWM Total Pulse Register" hexmask.long.word 0x04 0.--15. 1. " TPR ,Total pulse" line.long 0x08 "PR1,PWM Phase Ratio Register" hexmask.long.word 0x08 0.--15. 1. " PR ,Phase ratio" line.long 0x0C "DR1,PWM Duty Ratio Register" hexmask.long.word 0x0C 0.--15. 1. " DR ,Duty ratio" line.long 0x10 "CR1,PWM Condition Register" bitfld.long 0x10 3. " ONESHOT ,Single/continuous set register of PWM output pulse" "Continuous,Single" bitfld.long 0x10 2. " EXEDGE ,Negative/positive edge set register of external trigger start pulse" "Negative edge,Positive edge" textline " " bitfld.long 0x10 1. " EXTRG ,ON/OFF setting register of external trigger" "Off,On" bitfld.long 0x10 0. " POL ,Polarity setting register of PWM output pulse" "Negative pulse,Positive pulse" line.long 0x14 "SR1,PWM Start Register" bitfld.long 0x14 1. " SYNC ,Synchronization and setting registers of two channels" "Off,On" bitfld.long 0x14 0. " START ,PWM output start setting register" "Stopped,Started" rgroup.long (0x00+0x18)++0x03 line.long 0x00 "CCR1,PWM Current Count Register" hexmask.long.word 0x00 0.--15. 1. " CCR ,PWM base clock counter" group.long (0x00+0x1C)++0x03 line.long 0x00 "IR1,PWM Interrupt Register" bitfld.long 0x00 8.--9. " INTREP ,PWM interrupt output condition setting register" "NO,DONE,TRGDEC,DONE+TRGDEC" bitfld.long 0x00 1. " TRGDEC ,Trigger edge detection register" "Not detected,Detected" textline " " bitfld.long 0x00 0. " DONE ,Completion watch register of one PWM pulse cycle" "Not completed,Completed" textline "" group.long (0x80+0x00)++0x17 line.long 0x00 "BCR2,PWM Base Clock Register" hexmask.long.word 0x00 0.--15. 1. " BCR ,Cycle furation of PWM base clock to APB clock cycles" line.long 0x04 "TPR2,PWM Total Pulse Register" hexmask.long.word 0x04 0.--15. 1. " TPR ,Total pulse" line.long 0x08 "PR2,PWM Phase Ratio Register" hexmask.long.word 0x08 0.--15. 1. " PR ,Phase ratio" line.long 0x0C "DR2,PWM Duty Ratio Register" hexmask.long.word 0x0C 0.--15. 1. " DR ,Duty ratio" line.long 0x10 "CR2,PWM Condition Register" bitfld.long 0x10 3. " ONESHOT ,Single/continuous set register of PWM output pulse" "Continuous,Single" bitfld.long 0x10 2. " EXEDGE ,Negative/positive edge set register of external trigger start pulse" "Negative edge,Positive edge" textline " " bitfld.long 0x10 1. " EXTRG ,ON/OFF setting register of external trigger" "Off,On" bitfld.long 0x10 0. " POL ,Polarity setting register of PWM output pulse" "Negative pulse,Positive pulse" line.long 0x14 "SR2,PWM Start Register" bitfld.long 0x14 1. " SYNC ,Synchronization and setting registers of two channels" "Off,On" bitfld.long 0x14 0. " START ,PWM output start setting register" "Stopped,Started" rgroup.long (0x80+0x18)++0x03 line.long 0x00 "CCR2,PWM Current Count Register" hexmask.long.word 0x00 0.--15. 1. " CCR ,PWM base clock counter" group.long (0x80+0x1C)++0x03 line.long 0x00 "IR2,PWM Interrupt Register" bitfld.long 0x00 8.--9. " INTREP ,PWM interrupt output condition setting register" "NO,DONE,TRGDEC,DONE+TRGDEC" bitfld.long 0x00 1. " TRGDEC ,Trigger edge detection register" "Not detected,Detected" textline " " bitfld.long 0x00 0. " DONE ,Completion watch register of one PWM pulse cycle" "Not completed,Completed" textline "" group.long (0x100+0x00)++0x17 line.long 0x00 "BCR3,PWM Base Clock Register" hexmask.long.word 0x00 0.--15. 1. " BCR ,Cycle furation of PWM base clock to APB clock cycles" line.long 0x04 "TPR3,PWM Total Pulse Register" hexmask.long.word 0x04 0.--15. 1. " TPR ,Total pulse" line.long 0x08 "PR3,PWM Phase Ratio Register" hexmask.long.word 0x08 0.--15. 1. " PR ,Phase ratio" line.long 0x0C "DR3,PWM Duty Ratio Register" hexmask.long.word 0x0C 0.--15. 1. " DR ,Duty ratio" line.long 0x10 "CR3,PWM Condition Register" bitfld.long 0x10 3. " ONESHOT ,Single/continuous set register of PWM output pulse" "Continuous,Single" bitfld.long 0x10 2. " EXEDGE ,Negative/positive edge set register of external trigger start pulse" "Negative edge,Positive edge" textline " " bitfld.long 0x10 1. " EXTRG ,ON/OFF setting register of external trigger" "Off,On" bitfld.long 0x10 0. " POL ,Polarity setting register of PWM output pulse" "Negative pulse,Positive pulse" line.long 0x14 "SR3,PWM Start Register" bitfld.long 0x14 1. " SYNC ,Synchronization and setting registers of two channels" "Off,On" bitfld.long 0x14 0. " START ,PWM output start setting register" "Stopped,Started" rgroup.long (0x100+0x18)++0x03 line.long 0x00 "CCR3,PWM Current Count Register" hexmask.long.word 0x00 0.--15. 1. " CCR ,PWM base clock counter" group.long (0x100+0x1C)++0x03 line.long 0x00 "IR3,PWM Interrupt Register" bitfld.long 0x00 8.--9. " INTREP ,PWM interrupt output condition setting register" "NO,DONE,TRGDEC,DONE+TRGDEC" bitfld.long 0x00 1. " TRGDEC ,Trigger edge detection register" "Not detected,Detected" textline " " bitfld.long 0x00 0. " DONE ,Completion watch register of one PWM pulse cycle" "Not completed,Completed" textline "" group.long (0x180+0x00)++0x17 line.long 0x00 "BCR4,PWM Base Clock Register" hexmask.long.word 0x00 0.--15. 1. " BCR ,Cycle furation of PWM base clock to APB clock cycles" line.long 0x04 "TPR4,PWM Total Pulse Register" hexmask.long.word 0x04 0.--15. 1. " TPR ,Total pulse" line.long 0x08 "PR4,PWM Phase Ratio Register" hexmask.long.word 0x08 0.--15. 1. " PR ,Phase ratio" line.long 0x0C "DR4,PWM Duty Ratio Register" hexmask.long.word 0x0C 0.--15. 1. " DR ,Duty ratio" line.long 0x10 "CR4,PWM Condition Register" bitfld.long 0x10 3. " ONESHOT ,Single/continuous set register of PWM output pulse" "Continuous,Single" bitfld.long 0x10 2. " EXEDGE ,Negative/positive edge set register of external trigger start pulse" "Negative edge,Positive edge" textline " " bitfld.long 0x10 1. " EXTRG ,ON/OFF setting register of external trigger" "Off,On" bitfld.long 0x10 0. " POL ,Polarity setting register of PWM output pulse" "Negative pulse,Positive pulse" line.long 0x14 "SR4,PWM Start Register" bitfld.long 0x14 1. " SYNC ,Synchronization and setting registers of two channels" "Off,On" bitfld.long 0x14 0. " START ,PWM output start setting register" "Stopped,Started" rgroup.long (0x180+0x18)++0x03 line.long 0x00 "CCR4,PWM Current Count Register" hexmask.long.word 0x00 0.--15. 1. " CCR ,PWM base clock counter" group.long (0x180+0x1C)++0x03 line.long 0x00 "IR4,PWM Interrupt Register" bitfld.long 0x00 8.--9. " INTREP ,PWM interrupt output condition setting register" "NO,DONE,TRGDEC,DONE+TRGDEC" bitfld.long 0x00 1. " TRGDEC ,Trigger edge detection register" "Not detected,Detected" textline " " bitfld.long 0x00 0. " DONE ,Completion watch register of one PWM pulse cycle" "Not completed,Completed" textline "" width 0x0B tree.end tree "PWM 2" base ad:0x3C220000 width 10. group.long (0x00+0x00)++0x17 line.long 0x00 "BCR2,PWM Base Clock Register" hexmask.long.word 0x00 0.--15. 1. " BCR ,Cycle furation of PWM base clock to APB clock cycles" line.long 0x04 "TPR2,PWM Total Pulse Register" hexmask.long.word 0x04 0.--15. 1. " TPR ,Total pulse" line.long 0x08 "PR2,PWM Phase Ratio Register" hexmask.long.word 0x08 0.--15. 1. " PR ,Phase ratio" line.long 0x0C "DR2,PWM Duty Ratio Register" hexmask.long.word 0x0C 0.--15. 1. " DR ,Duty ratio" line.long 0x10 "CR2,PWM Condition Register" bitfld.long 0x10 3. " ONESHOT ,Single/continuous set register of PWM output pulse" "Continuous,Single" bitfld.long 0x10 2. " EXEDGE ,Negative/positive edge set register of external trigger start pulse" "Negative edge,Positive edge" textline " " bitfld.long 0x10 1. " EXTRG ,ON/OFF setting register of external trigger" "Off,On" bitfld.long 0x10 0. " POL ,Polarity setting register of PWM output pulse" "Negative pulse,Positive pulse" line.long 0x14 "SR2,PWM Start Register" bitfld.long 0x14 1. " SYNC ,Synchronization and setting registers of two channels" "Off,On" bitfld.long 0x14 0. " START ,PWM output start setting register" "Stopped,Started" rgroup.long (0x00+0x18)++0x03 line.long 0x00 "CCR2,PWM Current Count Register" hexmask.long.word 0x00 0.--15. 1. " CCR ,PWM base clock counter" group.long (0x00+0x1C)++0x03 line.long 0x00 "IR2,PWM Interrupt Register" bitfld.long 0x00 8.--9. " INTREP ,PWM interrupt output condition setting register" "NO,DONE,TRGDEC,DONE+TRGDEC" bitfld.long 0x00 1. " TRGDEC ,Trigger edge detection register" "Not detected,Detected" textline " " bitfld.long 0x00 0. " DONE ,Completion watch register of one PWM pulse cycle" "Not completed,Completed" textline "" group.long (0x80+0x00)++0x17 line.long 0x00 "BCR3,PWM Base Clock Register" hexmask.long.word 0x00 0.--15. 1. " BCR ,Cycle furation of PWM base clock to APB clock cycles" line.long 0x04 "TPR3,PWM Total Pulse Register" hexmask.long.word 0x04 0.--15. 1. " TPR ,Total pulse" line.long 0x08 "PR3,PWM Phase Ratio Register" hexmask.long.word 0x08 0.--15. 1. " PR ,Phase ratio" line.long 0x0C "DR3,PWM Duty Ratio Register" hexmask.long.word 0x0C 0.--15. 1. " DR ,Duty ratio" line.long 0x10 "CR3,PWM Condition Register" bitfld.long 0x10 3. " ONESHOT ,Single/continuous set register of PWM output pulse" "Continuous,Single" bitfld.long 0x10 2. " EXEDGE ,Negative/positive edge set register of external trigger start pulse" "Negative edge,Positive edge" textline " " bitfld.long 0x10 1. " EXTRG ,ON/OFF setting register of external trigger" "Off,On" bitfld.long 0x10 0. " POL ,Polarity setting register of PWM output pulse" "Negative pulse,Positive pulse" line.long 0x14 "SR3,PWM Start Register" bitfld.long 0x14 1. " SYNC ,Synchronization and setting registers of two channels" "Off,On" bitfld.long 0x14 0. " START ,PWM output start setting register" "Stopped,Started" rgroup.long (0x80+0x18)++0x03 line.long 0x00 "CCR3,PWM Current Count Register" hexmask.long.word 0x00 0.--15. 1. " CCR ,PWM base clock counter" group.long (0x80+0x1C)++0x03 line.long 0x00 "IR3,PWM Interrupt Register" bitfld.long 0x00 8.--9. " INTREP ,PWM interrupt output condition setting register" "NO,DONE,TRGDEC,DONE+TRGDEC" bitfld.long 0x00 1. " TRGDEC ,Trigger edge detection register" "Not detected,Detected" textline " " bitfld.long 0x00 0. " DONE ,Completion watch register of one PWM pulse cycle" "Not completed,Completed" textline "" group.long (0x100+0x00)++0x17 line.long 0x00 "BCR4,PWM Base Clock Register" hexmask.long.word 0x00 0.--15. 1. " BCR ,Cycle furation of PWM base clock to APB clock cycles" line.long 0x04 "TPR4,PWM Total Pulse Register" hexmask.long.word 0x04 0.--15. 1. " TPR ,Total pulse" line.long 0x08 "PR4,PWM Phase Ratio Register" hexmask.long.word 0x08 0.--15. 1. " PR ,Phase ratio" line.long 0x0C "DR4,PWM Duty Ratio Register" hexmask.long.word 0x0C 0.--15. 1. " DR ,Duty ratio" line.long 0x10 "CR4,PWM Condition Register" bitfld.long 0x10 3. " ONESHOT ,Single/continuous set register of PWM output pulse" "Continuous,Single" bitfld.long 0x10 2. " EXEDGE ,Negative/positive edge set register of external trigger start pulse" "Negative edge,Positive edge" textline " " bitfld.long 0x10 1. " EXTRG ,ON/OFF setting register of external trigger" "Off,On" bitfld.long 0x10 0. " POL ,Polarity setting register of PWM output pulse" "Negative pulse,Positive pulse" line.long 0x14 "SR4,PWM Start Register" bitfld.long 0x14 1. " SYNC ,Synchronization and setting registers of two channels" "Off,On" bitfld.long 0x14 0. " START ,PWM output start setting register" "Stopped,Started" rgroup.long (0x100+0x18)++0x03 line.long 0x00 "CCR4,PWM Current Count Register" hexmask.long.word 0x00 0.--15. 1. " CCR ,PWM base clock counter" group.long (0x100+0x1C)++0x03 line.long 0x00 "IR4,PWM Interrupt Register" bitfld.long 0x00 8.--9. " INTREP ,PWM interrupt output condition setting register" "NO,DONE,TRGDEC,DONE+TRGDEC" bitfld.long 0x00 1. " TRGDEC ,Trigger edge detection register" "Not detected,Detected" textline " " bitfld.long 0x00 0. " DONE ,Completion watch register of one PWM pulse cycle" "Not completed,Completed" textline "" group.long (0x180+0x00)++0x17 line.long 0x00 "BCR5,PWM Base Clock Register" hexmask.long.word 0x00 0.--15. 1. " BCR ,Cycle furation of PWM base clock to APB clock cycles" line.long 0x04 "TPR5,PWM Total Pulse Register" hexmask.long.word 0x04 0.--15. 1. " TPR ,Total pulse" line.long 0x08 "PR5,PWM Phase Ratio Register" hexmask.long.word 0x08 0.--15. 1. " PR ,Phase ratio" line.long 0x0C "DR5,PWM Duty Ratio Register" hexmask.long.word 0x0C 0.--15. 1. " DR ,Duty ratio" line.long 0x10 "CR5,PWM Condition Register" bitfld.long 0x10 3. " ONESHOT ,Single/continuous set register of PWM output pulse" "Continuous,Single" bitfld.long 0x10 2. " EXEDGE ,Negative/positive edge set register of external trigger start pulse" "Negative edge,Positive edge" textline " " bitfld.long 0x10 1. " EXTRG ,ON/OFF setting register of external trigger" "Off,On" bitfld.long 0x10 0. " POL ,Polarity setting register of PWM output pulse" "Negative pulse,Positive pulse" line.long 0x14 "SR5,PWM Start Register" bitfld.long 0x14 1. " SYNC ,Synchronization and setting registers of two channels" "Off,On" bitfld.long 0x14 0. " START ,PWM output start setting register" "Stopped,Started" rgroup.long (0x180+0x18)++0x03 line.long 0x00 "CCR5,PWM Current Count Register" hexmask.long.word 0x00 0.--15. 1. " CCR ,PWM base clock counter" group.long (0x180+0x1C)++0x03 line.long 0x00 "IR5,PWM Interrupt Register" bitfld.long 0x00 8.--9. " INTREP ,PWM interrupt output condition setting register" "NO,DONE,TRGDEC,DONE+TRGDEC" bitfld.long 0x00 1. " TRGDEC ,Trigger edge detection register" "Not detected,Detected" textline " " bitfld.long 0x00 0. " DONE ,Completion watch register of one PWM pulse cycle" "Not completed,Completed" textline "" width 0x0B tree.end tree.end tree "ADC (Analog-to-Digital Converter)" tree "ADC_1" base ad:0x3C100000 width 10. rgroup.long 0x00++0x03 line.long 0x00 "DATA,DATA" hexmask.long.word 0x00 0.--11. 1. " DATA ,Data storage register after analog to digital conversion" group.long 0x08++0x03 line.long 0x00 "XPD,Register that controls down of power of A/D Converter macro" bitfld.long 0x00 0. " XPD ,Register that controls down of power of A/D Converter macro" "Down of power setting,Down of power release" group.long 0x0C++0x0B line.long 0x00 "CK_SEL,Sampling clock frequency setting register of A/D Converter" bitfld.long 0x00 0.--2. " CK_SEL ,Sampling clock frequency setting register of A/D Converter" "1/1,1/2,1/3,1/4,1/5,1/6,1/7,1/8" line.long 0x04 "EOC,Register that shows A/D data update completion" bitfld.long 0x04 0. " EOC ,Whether it operates in A/D Converter can be confirmed by receiving the EOC signal from the A/D Converter" "Unreception,Reception" line.long 0x08 "EOC_MASK,Mask setting/release register" bitfld.long 0x08 0. " EOC_MSK ,Mask setting/release register of analog to digital conversion data update completion interrupt signal" "Mask setting,Mask release" width 0xb tree.end tree "ADC_2" base ad:0x3C110000 width 10. rgroup.long 0x00++0x03 line.long 0x00 "DATA,DATA" hexmask.long.word 0x00 0.--11. 1. " DATA ,Data storage register after analog to digital conversion" group.long 0x08++0x03 line.long 0x00 "XPD,Register that controls down of power of A/D Converter macro" bitfld.long 0x00 0. " XPD ,Register that controls down of power of A/D Converter macro" "Down of power setting,Down of power release" group.long 0x0C++0x0B line.long 0x00 "CK_SEL,Sampling clock frequency setting register of A/D Converter" bitfld.long 0x00 0.--2. " CK_SEL ,Sampling clock frequency setting register of A/D Converter" "1/1,1/2,1/3,1/4,1/5,1/6,1/7,1/8" line.long 0x04 "EOC,Register that shows A/D data update completion" bitfld.long 0x04 0. " EOC ,Whether it operates in A/D Converter can be confirmed by receiving the EOC signal from the A/D Converter" "Unreception,Reception" line.long 0x08 "EOC_MASK,Mask setting/release register" bitfld.long 0x08 0. " EOC_MSK ,Mask setting/release register of analog to digital conversion data update completion interrupt signal" "Mask setting,Mask release" width 0xb tree.end tree.end tree "GDC (Graphics display controller)" tree "Display 0" base ad:0xD0800000 width 25. group.long 0x00++0x03 line.long 0x00 "DISPLAYENABLE,Display Enable register" bitfld.long 0x00 0. " DEN ,DisplayEnable" "Disabled,Enabled" if (((per.l(ad:0xD0800000+0x04))&0x01)==0x01) group.long 0x04++0x03 line.long 0x00 "REGISTERUPDATEMODE,Defines the register update mode" bitfld.long 0x00 29. " RUMLAY_[0] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 28. " [1] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 27. " [2] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 26. " [3] ,Defines update mode" "Direct,Synchronous" textline " " bitfld.long 0x00 25. " [4] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 24. " [5] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 23. " [6] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 22. " [7] ,Defines update mode" "Direct,Synchronous" textline " " bitfld.long 0x00 21. " [8] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 20. " [9] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 19. " [10] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 18. " [11] ,Defines update mode" "Direct,Synchronous" textline " " bitfld.long 0x00 17. " [12] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 16. " [13] ,Defines update mode" "Direct,Synchronous" textline " " bitfld.long 0x00 1. " RUM ,Selects a mode during which register values are updated in sync with vertical synchronization globally" "Off,On" bitfld.long 0x00 0. " RUMSEL ,Selects the global register update mode" "Global,Per layer" else group.long 0x04++0x03 line.long 0x00 "REGISTERUPDATEMODE,Defines the register update mode" textline " " textline " " textline " " textline " " bitfld.long 0x00 1. " RUM ,Selects a mode during which register values are updated in sync with vertical synchronization globally" "Off,On" bitfld.long 0x00 0. " RUMSEL ,Selects the global register update mode" "Global,Per layer" endif textline " " group.long 0x08++0x1B line.long 0x00 "REGISTERUPDATESELECTION,Set the layers for synchronous update by vertical synchronization with RUFlag" sif (cpu()=="MB86R11F") hexmask.long.word 0x00 16.--29. 1. " RUFLAY ,Defines independently for each layer" textline " " endif bitfld.long 0x00 0. " RUFSEL ,Selects global update for all layers or independent update per layer" "Global,Per layer" textline " " line.long 0x04 "REGISTERUPDATEFLAG,Triggers the register update at next vertical synchronization" bitfld.long 0x04 29. " RUFLAY[13] ,Bit 13 layer update" "No update,Update" bitfld.long 0x04 28. " [12] ,Bit 12 layer update" "No update,Update" bitfld.long 0x04 27. " [11] ,Bit 11 layer update" "No update,Update" bitfld.long 0x04 26. " [10] ,Bit 10 layer update" "No update,Update" textline " " bitfld.long 0x04 25. " [9] ,Bit 9 layer update" "No update,Update" bitfld.long 0x04 24. " [8] ,Bit 8 layer update" "No update,Update" bitfld.long 0x04 23. " [7] ,Bit 7 layer update" "No update,Update" bitfld.long 0x04 22. " [6] ,Bit 6 layer update" "No update,Update" textline " " bitfld.long 0x04 21. " [5] ,Bit 5 layer update" "No update,Update" bitfld.long 0x04 20. " [4] ,Bit 4 layer update" "No update,Update" bitfld.long 0x04 19. " [3] ,Bit 3 layer update" "No update,Update" bitfld.long 0x04 18. " [2] ,Bit 2 layer update" "No update,Update" textline " " bitfld.long 0x04 17. " [1] ,Bit 1 layer update" "No update,Update" bitfld.long 0x04 16. " [0] ,Bit 0 layer update" "No update,Update" textline " " bitfld.long 0x04 0. " RUFLAG ,Instruction is issued to update selected layers" "Initial state/update completed,Vertical synchronization triggered" textline " " line.long 0x08 "DCLKCONFIG,Defines the pixel output clock" bitfld.long 0x08 25. " DPIXMODE ,Set Dual Pixel mode" "Not used,Used" bitfld.long 0x08 24. " RSDSMODE ,Set RSDS mode" "Not used,Used" sif (cpu()=="MB86R11F") bitfld.long 0x08 18.--22. " DCKDEL ,Defines an additional delay in units of the reference clock" "No additional delay,,+1 reference clock,,+2 reference clock,,+3 reference clock,,+4 reference clock,,+5 reference clock,,+6 reference clock,,+7 reference clock,,+8 reference clock,,+9 reference clock,,+10 reference clock,,+11 reference clock,,+12 reference clock,,+13 reference clock,,+14 reference clock,,+15 reference clock," else bitfld.long 0x08 18.--22. " DCKDEL ,Defines an additional delay in units of the reference clock" "No additional delay,,+2 reference clock,,+3 reference clock,,+4 reference clock,,+5 reference clock,,+6 reference clock,,+7 reference clock,,+8 reference clock,,+9 reference clock,,+10 reference clock,,+11 reference clock,,+12 reference clock,,+13 reference clock,,+14 reference clock,,+15 reference clock,,+16 reference clock," endif textline " " bitfld.long 0x08 17. " DCKDELEN ,Display clock delay" "Disabled,Enabled" bitfld.long 0x08 16. " DCKINV ,Inversion of display clock" "Not inverted,Inverted" bitfld.long 0x08 9.--14. " SC ,Divides the display reference clock by the set ratio for dot clocks generation" "Not divide,,,Divide the clock by 4,Divide the clock by 5,,,Divide the clock by 8,,,,,Divide the clock by 13,,,Divide the clock by 16,,,,,Divide the clock by 21,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,Divide the clock by 53,,,,,,,,,,Divide the clock by 63,Divide the clock by 64" textline " " bitfld.long 0x08 8. " DCSEL ,Selects the frequency of the reference input clock" "800/1066 MHz,Low" bitfld.long 0x08 0. " CKS ,Selects the reference clock" "PLL,DCLKI" line.long 0x0C "DISPLAYPORTCONFIG,Configuration of ports for synchronization signals" bitfld.long 0x0C 21. " TCONDELAY[5] ,Change TCON coutput timing of display" "No delay,Delay" bitfld.long 0x0C 20. " [4] ,Change TCON coutput timing of display" "No delay,Delay" bitfld.long 0x0C 19. " [3] ,Change TCON coutput timing of display" "No delay,Delay" bitfld.long 0x0C 18. " [2] ,Change TCON coutput timing of display" "No delay,Delay" bitfld.long 0x0C 17. " [1] ,Change TCON coutput timing of display" "No delay,Delay" bitfld.long 0x0C 16. " [0] ,Change TCON coutput timing of display" "No delay,Delay" textline " " bitfld.long 0x0C 3. " SYOUTEN ,Switch display YSNC and VSYNC pin direction" "INPUT Ports,OUTPUT Ports" bitfld.long 0x0C 1. " SF ,Sets synchronization active value" "Low active,High active" bitfld.long 0x0C 0. " ESY ,Enables external synchronization mode" "Disabled,Enabled" line.long 0x10 "DISPLAYRESOLUTION,Configuration of display resolution" hexmask.long.word 0x10 16.--27. 1. " VTR ,Specifies the vertical total line count" hexmask.long.word 0x10 0.--11. 1. " HTP ,Specifies the horizontal total pixel count" line.long 0x14 "ACTIVEAREA,Configuration of active video area" hexmask.long.word 0x14 16.--27. 1. " VDP ,Specifies the vertical display period in units of lines" hexmask.long.word 0x14 0.--11. 1. " HDP ,Specifies the horizontal display boundary in units of pixel" textline " " width 31. line.long 0x18 "HORSYNCHTIMINGCONFIGURATION,Configuration of the horizontal synchronization output timing" hexmask.long.byte 0x18 16.--23. 1. " HSW ,Specifies the pulse width of the horizontal synchronization signal in units of pixel" hexmask.long.word 0x18 0.--11. 1. " HSP ,Specifies the position of the horizontal synchronization signal in units of pixel" group.long 0x24++0x23 line.long 0x00 "VERSYNCHTIMINGCONFIGURATION,Configuration of the vertical synchronization output timing" bitfld.long 0x00 31. " VSWH ,Extends the pulse width of the vertical synchronization signal by half of a line" "0,1" hexmask.long.byte 0x00 16.--21. 1. " VSW ,Specifies the pulse width of the vertical synchronization signal in units of pixel clocks" textline " " hexmask.long.word 0x00 0.--11. 1. " VSP ,Specifies the position of the vertical synchronization signal in units of lines" line.long 0x04 "DISPLAYOUTPUTCONFIG,Configuration of output modes" bitfld.long 0x04 4. " DCKEDGE ,Defines the DCLK OUTPUT edge mode" "No equalization,Equalization" bitfld.long 0x04 3. " EEQ ,Sets the equalization pulse mode for the CSYNC signal" "EEQOFF,EEQON" textline " " bitfld.long 0x04 2. " POM ,Parallel Operation Mode" "Disabled,Enabled" bitfld.long 0x04 0.--1. " SYNC ,Sets display output mode" "NOINTLM,INTLM,,INTLVM" line.long 0x08 "MULTIDISPLAYDUALVIEWSETUP,Configuration of dual view processing" bitfld.long 0x08 31. " MDEN ,Enable multi-display functionality" "Disabled,Enabled" bitfld.long 0x08 2. " DVPATTERN ,Control the re-ordering between different lines" "Disabled,Enabled" textline " " bitfld.long 0x08 1. " DVDTSW ,Left and Right screen swapping" "Don't swap,Swap" bitfld.long 0x08 0. " DVEN ,DualView Enable" "Disabled,Enabled" line.long 0x0C "CHROMAKEYCONTROL,Configuration of chroma keying" bitfld.long 0x0C 31. " KCS ,Selects whether the display output color" "Display,L0 layer" bitfld.long 0x0C 30. " KYEN ,Enables chroma-key processing" "Disabled,Enabled" textline " " hexmask.long.tbyte 0x0C 0.--23. 1. " KYC ,Sets the key color used to perform chroma-key processing" line.long 0x10 "CLUTCONTROL,Enables/Disables the Color Lookup table" bitfld.long 0x10 31. " CLUTEN ,Enable Color Look Up" "Disabled,Enabled" line.long 0x14 "DITHERCONTROL,Configures the Dither unit" bitfld.long 0x14 4. " DITHMS ,Select mode for dithering" "Temporal dithering,Spatial dithering" bitfld.long 0x14 3. " DITHRS ,Sets dither range" "Add '1' to lower bits,Add '1' to higher bits" textline " " bitfld.long 0x14 1.--2. " DITHFS ,Select output format for dithering" "10x10x10->8x8x8,10x10x10->7x7x7,10x10x10->6x6x6,10x10x10->5x6x5" bitfld.long 0x14 0. " DITHEN ,Enable Dithering" "Disabled,Enabled" line.long 0x18 "DISPLAYBACKGROUNDCOLOR,This color is displayed on screen areas that are not included in any display window" bitfld.long 0x18 31. " DBGEN ,Enable the background color" "Not blended,Blended" hexmask.long.byte 0x18 16.--23. 1. " DBGR ,Specifies the red level of the background color" textline " " hexmask.long.byte 0x18 8.--15. 1. " DBGG ,Specifies the green level of the background color" hexmask.long.byte 0x18 0.--7. 1. " DBGB ,Specifies the blue level of the background color" line.long 0x20 "DISPLAYLAYERSELECT,Defines the layer superimposition order" textline " " bitfld.long 0x20 28.--31. " DLS_[7] ,Selects the bottom layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 24.--27. " [6] ,Selects the seventh layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 20.--23. " [5] ,Selects the sixth layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 16.--19. " [4] ,Selects the fifth layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" textline " " bitfld.long 0x20 12.--15. " [3] ,Selects the fourth layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 8.--11. " [2] ,Selects the third layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 4.--7. " [1] ,Selects the second layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 0.--3. " [0] ,Selects the top layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" textline " " group.long 0x44++0x23 line.long 0x00 "COMPATIBILITYMODE,Handles RUBY compatibility" bitfld.long 0x00 4. " RUBYMD ,Ruby Mode" "Ruby mode off,Ruby mode on" bitfld.long 0x00 0. " AH ,Address high keep this bit zero" "0,1" line.long 0x04 "L0LAYERMODE,L0LayerMode" bitfld.long 0x04 31. " L0E ,Enables L0 layer display" "Disabled,Enabled" bitfld.long 0x04 30. " SC1EN0 ,SC1en0" "Not included,Included" textline " " bitfld.long 0x04 29. " SC0EN0 ,SC0en0" "Not included,Included" hexmask.long.byte 0x04 16.--23. 1. " L0W ,Sets the memory width (stride) of the L0 layer logical frame in units of 64 bytes" textline " " hexmask.long.word 0x04 0.--11. 1. " L0H ,Specifies the height of the L0 layer logical frame in units of pixels" line.long 0x08 "L0COLORMODE,L0ColorMode" bitfld.long 0x08 8.--10. " L0CMODE ,Sets the L0 layer color mode" "16b/p ARGB mode,24b/p ARGB mode,16b/p RGBA mode,24b/p RGBA mode,24b/p ABGR mode,Indirect color 8 b/p mode,16b/p RGB565 mode," bitfld.long 0x08 0.--3. " L0PB ,Indicates the value added to the index when using the L0 layer palette" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x0C "L0ORIGINADDRESS,L0OriginAddress" line.long 0x10 "L0DISPLAYADDRESS,L0DisplayAddress" line.long 0x14 "L0DISPLAYPOSITION,Sets the display position coordinates (DX,DY) of the L0 layer" hexmask.long.word 0x14 16.--27. 1. " L0DY ,Specifies the DY coordinate" hexmask.long.word 0x14 0.--11. 1. " L0DX ,Specifies the DX coordinate" line.long 0x18 "L0WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the L0 layer window" hexmask.long.word 0x18 16.--27. 1. " L0WY ,Specifies theWY coordinate" hexmask.long.word 0x18 0.--11. 1. " L0WX ,Specifies the WX coordinate" line.long 0x1C "L0WINDOWSIZE,Sets the size of the L0 layer window" hexmask.long.word 0x1C 16.--27. 1. " L0WH ,Specifies the height" hexmask.long.word 0x1C 0.--11. 1. " L0WW ,Specifies the width in units of pixels" line.long 0x20 "L0READSKIPMODE,Controls read skip operation of layer L0" bitfld.long 0x20 15. " L0SE ,Specifies whether or not to enable the read skip function" "Disabled,Enabled" hexmask.long.word 0x20 0.--8. 1. " L0PRE ,Specifies whether or not to perform a read operation for the partition corresponding to each bit" group.long 0x68++0x0F line.long 0x00 "L0PARTITIONX,Specifies two X coordinates which split the L0 layer when performing a read skip" hexmask.long.word 0x00 16.--27. 1. " L0PX1 ,Specifies the second X coordinate for read skip partition" hexmask.long.word 0x00 0.--11. 1. " L0PX0 ,Specifies the first X coordinate for read skip partition" line.long 0x04 "L0PARTITIONY,Specifies two Y coordinates which split the L0 layer when performing a read skip" hexmask.long.word 0x04 16.--27. 1. " L0PY1 ,Specifies the second Y coordinate for read skip partition" hexmask.long.word 0x04 0.--11. 1. " L0PY0 ,Specifies the first Y coordinate for read skip partition" line.long 0x08 "L0BLEND,Configures blending operation of Layer 0" bitfld.long 0x08 16.--18. " L0BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x08 14. " L0BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x08 13. " L0BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x08 11.--12. " L0AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x08 10. " L0AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x08 9. " L0AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x08 0.--8. 1. " L0BR ,Sets the blend ratio" line.long 0x0C "L0TRANSPARENCYCONTROL,Controls transparency processing of Layer 0" bitfld.long 0x0C 31. " L0ZT ,Enables transparent processing for Layer L0" "Disabled,Enabled" hexmask.long.tbyte 0x0C 0.--23. 1. " L0TC ,Sets the color value (code) treated as transparent color for L0 layer" group.long 0x78++0x0B line.long 0x00 "L1LAYERMODE,1LayerMode" bitfld.long 0x00 31. " L1E ,Enables L1 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1en1 ,SC1en1" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0EN1 ,SC0en1" "Not included,Included" bitfld.long 0x00 20. " L1ENBWAUTO ,Set an automatic video capture operation mode when L1CS is in capture mode" "No automatic mode,Automatic Buffer managment" textline " " bitfld.long 0x00 19. " L1YC ,Sets the L1 layer color format" "RGB mode,YC mode" bitfld.long 0x00 18. " L1CS ,Sets whether to use the L1 layer as a normal display layer or as a video capture layer" "Normal mode,Video Capture mode" textline " " bitfld.long 0x00 17. " L1INTL ,Sets a video capture operation mode" "Normal mode,WEAVE mode" bitfld.long 0x00 16. " L1VMAG ,Enables capture image upscaling" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 0.--7. 1. " L1W ,Sets the memory width (stride) of the L1 layer logical frame in units of 64 bytes" line.long 0x04 "L1COLORMODE,L1ColorMode" bitfld.long 0x04 8.--10. " L1CMODE ,Sets the L1 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,16b/p RGB565 mode," bitfld.long 0x04 0.--3. " L1PB ,Indicates the value to be added to the index when drawing the L1 layer palette" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "L1DISPLAYADDRESS,Sets the display window origin address of the L1 layer" rgroup.long 0x84++0x07 line.long 0x00 "CAPTURE1BUFFERDISPLAYADDRESS0,Starting address of the displayed capture image" line.long 0x04 "CAPTURE1BUFFERDISPLAYADDRESS1,This register indicates the starting address of an even field of the capture screen" group.long 0x8C++0x07 line.long 0x00 "L1WINDOWPOSITION,L1WindowPosition" hexmask.long.word 0x00 16.--27. 1. " L1WY ,Sets the display position coordinates (WY) of the L1 layer window" hexmask.long.word 0x00 0.--11. 1. " L1WX ,Sets the display position coordinates (WX) of the L1 layer window" line.long 0x04 "L1WINDOWSIZE,L1WindowSize" hexmask.long.word 0x04 16.--27. 1. " L1WH ,Sets the size of the L1 layer window. Specifies the height" hexmask.long.word 0x04 0.--11. 1. " L1WW ,Sets the size of the L1 layer window.Specifies the width in units of pixels" group.long 0x9C++0x07 line.long 0x00 "L1BLEND,Configures blending operation of Layer 1" bitfld.long 0x00 16.--18. " L1BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x00 14. " L1BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x00 13. " L1BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x00 11.--12. " L1AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x00 10. " L1AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x00 9. " L1AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x00 0.--8. 1. " L1BR ,Sets the blend ratio" line.long 0x04 "L1TRANSPARENCYCONTROL,Controls transparency processing of Layer 1" bitfld.long 0x04 31. " L1ZT ,Enables transparent processing for Layer L1" "Disabled,Enabled" hexmask.long.tbyte 0x04 0.--23. 1. " L1TC ,Sets the color value (code) treated as transparent color for L1 layer" group.long 0xA4++0x1B line.long 0x00 "L2LAYERMODE,2LayerMode" bitfld.long 0x00 31. " L2E ,Enables L2 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1en2 ,SC1en2" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0EN2 ,SC0en2" "Not included,Included" bitfld.long 0x00 20. " L2ENBWAUTO ,Set an automatic video capture operation mode when L2CS is in capture mode" "No automatic mode,Automatic Buffer managment" textline " " bitfld.long 0x00 19. " L2YC ,Sets the L2 layer color format" "RGB mode,YC mode" bitfld.long 0x00 18. " L2CS ,Sets whether to use the L2 layer as a normal display layer or as a video capture layer" "Normal mode,Video Capture mode" textline " " bitfld.long 0x00 17. " L2INTL ,Sets a video capture operation mode" "Normal mode,WEAVE mode" bitfld.long 0x00 16. " L2VMAG ,Enable capture image upscaling" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 0.--7. 1. " L2W ,Sets the memory width (stride) of the L2 layer logical frame in units of 64 bytes" line.long 0x04 "L2COLORMODE,L2ColorMode" bitfld.long 0x04 8.--10. " L2CMODE ,Sets the L2 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,16b/p RGB565 mode," bitfld.long 0x04 0.--3. " L2PB ,Indicates the value to be added to the index when drawing the L2 layer palette" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "L2DISPLAYADDRESS,Sets the display window origin address of the L2 layer" line.long 0x0C "CAPTURE2BUFFERDISPLAYADDRESS0,Starting address of the displayed capture image" line.long 0x10 "CAPTURE2BUFFERDISPLAYADDRESS1,This register indicates the starting address of an even field of the capture screen" line.long 0x14 "L2WINDOWPOSITION,L2WindowPosition" hexmask.long.word 0x14 16.--27. 1. " L2WY ,Sets the display position coordinates (WY) of the L2 layer window" hexmask.long.word 0x14 0.--11. 1. " L2WX ,Sets the display position coordinates (WX) of the L2 layer window" line.long 0x18 "L2WINDOWSIZE,L2WindowSize" hexmask.long.word 0x18 16.--27. 1. " L2WH ,Sets the size of the L2 layer window. Specifies the height" hexmask.long.word 0x18 0.--11. 1. " L2WW ,Sets the size of the L2 layer window.Specifies the width in units of pixels" group.long 0xC8++0x07 line.long 0x00 "L2BLEND,Configures blending operation of Layer 2" bitfld.long 0x00 16.--18. " L2BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x00 14. " L2BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x00 13. " L2BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x00 11.--12. " L2AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x00 10. " L2AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x00 9. " L2AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x00 0.--8. 1. " L2BR ,Sets the blend ratio" line.long 0x04 "L2TRANSPARENCYCONTROL,Controls transparency processing of Layer 2" bitfld.long 0x04 31. " L2ZT ,Enables transparent processing for Layer L2" "Disabled,Enabled" hexmask.long.tbyte 0x04 0.--23. 1. " L2TC ,Sets the color value (code) treated as transparent color for L2 layer" group.long 0xD0++0x1B line.long 0x00 "L3LAYERMODE,3LayerMode" bitfld.long 0x00 31. " L3E ,Enables L3 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1en3 ,SC1en3" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0EN3 ,SC0en3" "Not included,Included" bitfld.long 0x00 20. " L3ENBWAUTO ,Set an automatic video capture operation mode when L3CS is in capture mode" "No automatic mode,Automatic Buffer managment" textline " " bitfld.long 0x00 19. " L3YC ,Sets the L3 layer color format" "RGB mode,YC mode" bitfld.long 0x00 18. " L3CS ,Sets whether to use the L3 layer as a normal display layer or as a video capture layer" "Normal mode,Video Capture mode" textline " " bitfld.long 0x00 17. " L3INTL ,Sets a video capture operation mode" "Normal mode,WEAVE mode" bitfld.long 0x00 16. " L3VMAG ,Enable capture image upscaling" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 0.--7. 1. " L3W ,Sets the memory width (stride) of the L3layer logical frame in units of 64 bytes" line.long 0x04 "L3COLORMODE,L3ColorMode" bitfld.long 0x04 8.--10. " L3CMODE ,Sets the L3 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,16b/p RGB565 mode," bitfld.long 0x04 0.--3. " L3PB ,Indicates the value to be added to the index when drawing the L3 layer palette" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "L3DISPLAYADDRESS,Sets the display window origin address of the L3 layer" line.long 0x0C "CAPTURE3BUFFERDISPLAYADDRESS0,Starting address of the displayed capture image" line.long 0x10 "CAPTURE3BUFFERDISPLAYADDRESS1,This register indicates the starting address of an even field of the capture screen" line.long 0x14 "L3WINDOWPOSITION,L3WindowPosition" hexmask.long.word 0x14 16.--27. 1. " L3WY ,Sets the display position coordinates (WY) of the L3 layer window" hexmask.long.word 0x14 0.--11. 1. " L3WX ,Sets the display position coordinates (WX) of the L3 layer window" line.long 0x18 "L3WINDOWSIZE,L3WindowSize" hexmask.long.word 0x18 16.--27. 1. " L3WH ,Sets the size of the L3 layer window. Specifies the height" hexmask.long.word 0x18 0.--11. 1. " L3WW ,Sets the size of the L3 layer window.Specifies the width in units of pixels" group.long 0xF4++0x07 line.long 0x00 "L3BLEND,Configures blending operation of Layer 3" bitfld.long 0x00 16.--18. " L3BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x00 14. " L3BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x00 13. " L3BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x00 11.--12. " L3AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x00 10. " L3AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x00 9. " L3AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x00 0.--8. 1. " L3BR ,Sets the blend ratio" line.long 0x04 "L3TRANSPARENCYCONTROL,Controls transparency processing of Layer 3" bitfld.long 0x04 31. " L3ZT ,Enables transparent processing for Layer L3" "Disabled,Enabled" hexmask.long.tbyte 0x04 0.--23. 1. " L3TC ,Sets the color value (code) treated as transparent color for L3 layer" group.long 0xFC++0x03 line.long 0x00 "L4LAYERMODE,4LayerMode" bitfld.long 0x00 31. " L4E ,Enables L4 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1en4 ,SC1en4" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0EN4 ,SC0en4" "Not included,Included" bitfld.long 0x00 20. " L4ENBWAUTO ,Set an automatic video capture operation mode when L4CS is in capture mode" "No automatic mode,Automatic Buffer managment" textline " " bitfld.long 0x00 19. " L4YC ,Sets the L4 layer color format" "RGB mode,YC mode" bitfld.long 0x00 18. " L4CS ,Sets whether to use the L4 layer as a normal display layer or as a video capture layer" "Normal mode,Video Capture mode" textline " " bitfld.long 0x00 17. " L4INTL ,Sets a video capture operation mode" "Normal mode,WEAVE mode" bitfld.long 0x00 16. " L4VMAG ,Enable capture image upscaling" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 0.--7. 1. " L4W ,Sets the memory width (stride) of the L4layer logical frame in units of 64 bytes" group.long 0x100++0x17 line.long 0x00 "L4COLORMODE,L4ColorMode" bitfld.long 0x00 8.--10. " L4CMODE ,Sets the L4 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,16b/p RGB565 mode," line.long 0x04 "L4DISPLAYADDRESS,Sets the display window origin address of the L4 layer" line.long 0x08 "CAPTURE4BUFFERDISPLAYADDRESS0,Starting address of the displayed capture image" line.long 0x0C "CAPTURE4BUFFERDISPLAYADDRESS1,This register indicates the starting address of an even field of the capture screen" line.long 0x10 "L4WINDOWPOSITION,L4WindowPosition" hexmask.long.word 0x10 16.--27. 1. " L4WY ,Sets the display position coordinates (WY) of the L4 layer window" hexmask.long.word 0x10 0.--11. 1. " L4WX ,Sets the display position coordinates (WX) of the L4 layer window" line.long 0x14 "L4WINDOWSIZE,L4WindowSize" hexmask.long.word 0x14 16.--27. 1. " L4WH ,Sets the size of the L4 layer window. Specifies the height" hexmask.long.word 0x14 0.--11. 1. " L4WW ,Sets the size of the L4 layer window.Specifies the width in units of pixels" group.long 0x120++0x07 line.long 0x00 "L4BLEND,Configures blending operation of Layer 4" bitfld.long 0x00 16.--18. " L4BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x00 14. " L4BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x00 13. " L4BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x00 11.--12. " L4AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x00 10. " L4AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x00 9. " L4AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x00 0.--8. 1. " L4BR ,Sets the blend ratio" line.long 0x04 "L4TRANSPARENCYCONTROL,Controls transparency processing of Layer 4" bitfld.long 0x04 31. " L4ZT ,Enables transparent processing for Layer L4" "Disabled,Enabled" hexmask.long.tbyte 0x04 0.--23. 1. " L4TC ,Sets the color value (code) treated as transparent color for L4 layer" group.long 0x128++0x3 line.long 0x00 "L5LAYERMODE,5LayerMode" bitfld.long 0x00 31. " L5E ,Enables L5 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1EN5 ,SC1en5" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0EN5 ,SC0en5" "Not included,Included" hexmask.long.byte 0x00 16.--23. 1. " L5W ,Sets the memory width (stride) of the L5 layer logical frame in units of 64 bytes" textline " " hexmask.long.word 0x00 0.--11. 1. " L5H ,Specifies the height of the L5 layer logical frame in units of pixels" group.long 0x12C++0x17 line.long 0x00 "L5COLORMODE,L5ColorMode" bitfld.long 0x00 8.--10. " L5CMODE ,Sets the L5 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,16b/p RGB565 mode," line.long 0x04 "L5ORIGINADDRESS,Sets the logical frame origin address of L5 layer" line.long 0x08 "L5DISPLAYADDRESS,Sets the display origin address of L5 layer" line.long 0x0C "L5DISPLAYPOSITION,L5DisplayPosition" line.long 0x10 "L5WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the L5 layer window" hexmask.long.word 0x10 16.--27. 1. " L5WY ,Sets the display position coordinates (WY) of the L5 layer window" hexmask.long.word 0x10 0.--11. 1. " L5WX ,Sets the display position coordinates (WX) of the L5 layer window" line.long 0x14 "L5WINDOWSIZE,L5WindowSize" hexmask.long.word 0x14 16.--27. 1. " L5WH ,Sets the size of the L5 layer window. Specifies the height" hexmask.long.word 0x14 0.--11. 1. " L5WW ,Sets the size of the L5 layer window.Specifies the width in units of pixels" group.long 0x144++0x13 line.long 0x00 "L5READSKIPMODE,Controls read skip operation of layer L5" bitfld.long 0x00 15. " L0SE ,Specifies whether or not to enable the read skip function" "Disabled,Enabled" hexmask.long.word 0x00 0.--8. 1. " L0PRE ,Specifies whether or not to perform a read operation for the partition corresponding to each bit" line.long 0x04 "L5PARTITIONX,Specifies two X coordinates which split the L5 layer when performing a read skip" hexmask.long.word 0x04 16.--27. 1. " L0PX1 ,Specifies the second X coordinate for read skip partition" hexmask.long.word 0x04 0.--11. 1. " L0PX0 ,Specifies the first X coordinate for read skip partition" line.long 0x08 "L5PARTITIONY,Specifies two Y coordinates which split the L5 layer when performing a read skip" hexmask.long.word 0x08 16.--27. 1. " L0PY1 ,Specifies the second Y coordinate for read skip partition" hexmask.long.word 0x08 0.--11. 1. " L0PY0 ,Specifies the first Y coordinate for read skip partition" line.long 0x0C "L5BLEND,Configures blending operation of Layer 5" bitfld.long 0x0C 16.--18. " L5BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x0C 14. " L5BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x0C 13. " L5BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x0C 11.--12. " L5AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x0C 10. " L5AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x0C 9. " L5AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x0C 0.--8. 1. " L5BR ,Sets the blend ratio" line.long 0x10 "L5TRANSPARENCYCONTROL,Controls transparency processing of Layer 5" bitfld.long 0x10 31. " L5ZT ,Enables transparent processing for Layer L5" "Disabled,Enabled" hexmask.long.tbyte 0x10 0.--23. 1. " L5TC ,Sets the color value (code) treated as transparent color for L5 layer" group.long 0x158++0x3 line.long 0x00 "L6LAYERMODE,6LayerMode" bitfld.long 0x00 31. " L5E ,Enables L6 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1en6 ,SC1en6" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0EN6 ,SC0en6" "Not included,Included" hexmask.long.byte 0x00 16.--23. 1. " L6W ,Sets the memory width (stride) of the L6 layer logical frame in units of 64 bytes" textline " " hexmask.long.word 0x00 0.--11. 1. " L6H ,Specifies the height of the L6 layer logical frame in units of pixels" group.long 0x15C++0x17 line.long 0x00 "L6COLORMODE,L6ColorMode" bitfld.long 0x00 8.--10. " L6CMODE ,Sets the L6 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,16b/p RGB565 mode," line.long 0x04 "L6ORIGINADDRESS,Sets the logical frame origin address of L6 layer" line.long 0x08 "L6DISPLAYADDRESS,Sets the display origin address of L6 layer" line.long 0x0C "L6DISPLAYPOSITION,L6DisplayPosition" line.long 0x10 "L6WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the L6 layer window" hexmask.long.word 0x10 16.--27. 1. " L6WY ,Sets the display position coordinates (WY) of the L6 layer window" hexmask.long.word 0x10 0.--11. 1. " L6WX ,Sets the display position coordinates (WX) of the L6 layer window" line.long 0x14 "L6WINDOWSIZE,L6WindowSize" hexmask.long.word 0x14 16.--27. 1. " L6WH ,Sets the size of the L6 layer window. Specifies the height" hexmask.long.word 0x14 0.--11. 1. " L6WW ,Sets the size of the L6 layer window.Specifies the width in units of pixels" group.long 0x174++0x13 line.long 0x00 "L6READSKIPMODE,Controls read skip operation of layer L6" bitfld.long 0x00 15. " L6SE ,Specifies whether or not to enable the read skip function" "Disabled,Enabled" hexmask.long.word 0x00 0.--8. 1. " L6PRE ,Specifies whether or not to perform a read operation for the partition corresponding to each bit" line.long 0x04 "L6PARTITIONX,Specifies two X coordinates which split the L6 layer when performing a read skip" hexmask.long.word 0x04 16.--27. 1. " L6PX1 ,Specifies the second X coordinate for read skip partition" hexmask.long.word 0x04 0.--11. 1. " L6PX0 ,Specifies the first X coordinate for read skip partition" line.long 0x08 "L6PARTITIONY,Specifies two Y coordinates which split the L6 layer when performing a read skip" hexmask.long.word 0x08 16.--27. 1. " L6PY1 ,Specifies the second Y coordinate for read skip partition" hexmask.long.word 0x08 0.--11. 1. " L6PY0 ,Specifies the first Y coordinate for read skip partition" line.long 0x0C "L6BLEND,Configures blending operation of Layer 6" bitfld.long 0x0C 16.--18. " L6BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x0C 14. " L6BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x0C 13. " L6BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x0C 11.--12. " L6AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x0C 10. " L6AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x0C 9. " L6AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x0C 0.--8. 1. " L6BR ,Sets the blend ratio" line.long 0x10 "L6TRANSPARENCYCONTROL,Controls transparency processing of Layer 6" bitfld.long 0x10 31. " L6ZT ,Enables transparent processing for Layer L6" "Disabled,Enabled" hexmask.long.tbyte 0x10 0.--23. 1. " L6TC ,Sets the color value (code) treated as transparent color for L6 layer" group.long 0x188++0x3 line.long 0x00 "L7LAYERMODE,7LayerMode" bitfld.long 0x00 31. " L7E ,Enables L7 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1EN7 ,SC1en6" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0EN7 ,SC0en7" "Not included,Included" hexmask.long.byte 0x00 16.--23. 1. " L7W ,Sets the memory width (stride) of the L7 layer logical frame in units of 64 bytes" textline " " hexmask.long.word 0x00 0.--11. 1. " L7H ,Specifies the height of the L7 layer logical frame in units of pixels" group.long 0x18C++0x17 line.long 0x00 "L7COLORMODE,L7ColorMode" bitfld.long 0x00 8.--10. " L7CMODE ,Sets the L7 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,16b/p RGB565 mode," line.long 0x04 "L7ORIGINADDRESS,Sets the logical frame origin address of L7 layer" line.long 0x08 "L7DISPLAYADDRESS,Sets the display origin address of L7 layer" line.long 0x0C "L7DISPLAYPOSITION,L7DisplayPosition" line.long 0x10 "L7WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the L7 layer window" hexmask.long.word 0x10 16.--27. 1. " L7WY ,Sets the display position coordinates (WY) of the L7 layer window" hexmask.long.word 0x10 0.--11. 1. " L7WX ,Sets the display position coordinates (WX) of the L7 layer window" line.long 0x14 "L7WINDOWSIZE,L7WindowSize" hexmask.long.word 0x14 16.--27. 1. " L7WH ,Sets the size of the L7 layer window. Specifies the height" hexmask.long.word 0x14 0.--11. 1. " L7WW ,Sets the size of the L7 layer window.Specifies the width in units of pixels" group.long 0x1A4++0x13 line.long 0x00 "L7READSKIPMODE,Controls read skip operation of layer L7" bitfld.long 0x00 15. " L7SE ,Specifies whether or not to enable the read skip function" "Disabled,Enabled" hexmask.long.word 0x00 0.--8. 1. " L7PRE ,Specifies whether or not to perform a read operation for the partition corresponding to each bit" line.long 0x04 "L7PARTITIONX,Specifies two X coordinates which split the L7 layer when performing a read skip" hexmask.long.word 0x04 16.--27. 1. " L7PX1 ,Specifies the second X coordinate for read skip partition" hexmask.long.word 0x04 0.--11. 1. " L7PX0 ,Specifies the first X coordinate for read skip partition" line.long 0x08 "L7PARTITIONY,Specifies two Y coordinates which split the L7 layer when performing a read skip" hexmask.long.word 0x08 16.--27. 1. " L7PY1 ,Specifies the second Y coordinate for read skip partition" hexmask.long.word 0x08 0.--11. 1. " L7PY0 ,Specifies the first Y coordinate for read skip partition" line.long 0x0C "L7BLEND,Configures blending operation of Layer 7" bitfld.long 0x0C 16.--18. " L7BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x0C 14. " L7BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x0C 13. " L7BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x0C 11.--12. " L7AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x0C 10. " L7AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x0C 9. " L7AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x0C 0.--8. 1. " L7BR ,Sets the blend ratio" line.long 0x10 "L7TRANSPARENCYCONTROL,Controls transparency processing of Layer 7" bitfld.long 0x10 31. " L7ZT ,Enables transparent processing for Layer L7" "Disabled,Enabled" hexmask.long.tbyte 0x10 0.--23. 1. " L7TC ,Sets the color value (code) treated as transparent color for L7 layer" group.long 0x1B8++0x0F line.long 0x00 "LA0LAYERMODE,LA0LayerMode" bitfld.long 0x00 31. " LA0E ,Enables the LA0 layer" "Disabled,Enabled" hexmask.long.byte 0x00 0.--7. 1. " LA0W ,Sets the memory width (stride) of the LA0 layer logical frame in units of 64 bytes" line.long 0x04 "LA0DISPLAYADDRESS,LA0DisplayAddress" line.long 0x08 "LA0WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the LA0 layer window" hexmask.long.word 0x08 16.--27. 1. " LA0WY ,Specifies the WY coordinate" hexmask.long.word 0x08 0.--11. 1. " LA0WX ,Specifies the WX coordinate" line.long 0x0C "LA0WINDOWSIZE,Sets the size of the LA0 layer window" hexmask.long.word 0x0C 16.--27. 1. " LA0WH ,Specifies the height" hexmask.long.word 0x0C 0.--11. 1. " LA0WW ,Specifies the width in units of pixels" group.long 0x1C8++0x0F line.long 0x00 "LA1LAYERMODE,LA1LayerMode" bitfld.long 0x00 31. " LA1E ,Enables the LA1 layer" "Disabled,Enabled" hexmask.long.byte 0x00 0.--7. 1. " LA1W ,Sets the memory width (stride) of the LA1 layer logical frame in units of 64 bytes" line.long 0x04 "LA1DISPLAYADDRESS,LA1DisplayAddress" line.long 0x08 "LA1WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the LA1 layer window" hexmask.long.word 0x08 16.--27. 1. " LA1WY ,Specifies the WY coordinate" hexmask.long.word 0x08 0.--11. 1. " LA1WX ,Specifies the WX coordinate" line.long 0x0C "LA1WINDOWSIZE,Sets the size of the LA1 layer window" hexmask.long.word 0x0C 16.--27. 1. " LA1WH ,Specifies the height" hexmask.long.word 0x0C 0.--11. 1. " LA1WW ,Specifies the width in units of pixels" group.long 0x1D8++0x0F line.long 0x00 "LA2LAYERMODE,LA2LayerMode" bitfld.long 0x00 31. " LA2E ,Enables the LA2 layer" "Disabled,Enabled" hexmask.long.byte 0x00 0.--7. 1. " LA2W ,Sets the memory width (stride) of the LA2 layer logical frame in units of 64 bytes" line.long 0x04 "LA2DISPLAYADDRESS,LA2DisplayAddress" line.long 0x08 "LA2WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the LA2 layer window" hexmask.long.word 0x08 16.--27. 1. " LA2WY ,Specifies the WY coordinate" hexmask.long.word 0x08 0.--11. 1. " LA2WX ,Specifies the WX coordinate" line.long 0x0C "LA2WINDOWSIZE,Sets the size of the LA2 layer window" hexmask.long.word 0x0C 16.--27. 1. " LA2WH ,Specifies the height" hexmask.long.word 0x0C 0.--11. 1. " LA2WW ,Specifies the width in units of pixels" group.long 0x1E8++0x0F line.long 0x00 "LA3LAYERMODE,LA3LayerMode" bitfld.long 0x00 31. " LA3E ,Enables the LA3 layer" "Disabled,Enabled" hexmask.long.byte 0x00 0.--7. 1. " LA3W ,Sets the memory width (stride) of the LA3 layer logical frame in units of 64 bytes" line.long 0x04 "LA3DISPLAYADDRESS,LA3DisplayAddress" line.long 0x08 "LA3WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the LA3 layer window" hexmask.long.word 0x08 16.--27. 1. " LA3WY ,Specifies the WY coordinate" hexmask.long.word 0x08 0.--11. 1. " LA3WX ,Specifies the WX coordinate" line.long 0x0C "LA3WINDOWSIZE,Sets the size of the LA3 layer window" hexmask.long.word 0x0C 16.--27. 1. " LA3WH ,Specifies the height" hexmask.long.word 0x0C 0.--11. 1. " LA3WW ,Specifies the width in units of pixels" group.long 0x1F8++0x0F line.long 0x00 "CURSOR0PRIORITYMODE,Sets the priority of cursor display" bitfld.long 0x00 31. " CEN0 ,Enables/disables display of cursor 0" "Disabled,Enabled" bitfld.long 0x00 30. " SC1ENC0 ,Determines whether cursor0 is included in screen1 or not" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0ENC0 ,Determines whether cursor0 is included in screen0 or not" "Not included,Included" bitfld.long 0x00 1.--2. " CU0SIZ ,Sets Size of cursor 0" "128x128,64x64,32x32,16x16" textline " " bitfld.long 0x00 0. " CUO0 ,Sets the display priority of cursor 0 and the L0 layer" "Below,Above" line.long 0x04 "CURSOR0ORIGINADDRESS,Cursor0OriginAddress" line.long 0x08 "CURSOR0POSITION,Sets the display position coordinates (CUX0,CUY0) of cursor 0 in units of pixels" hexmask.long.word 0x08 16.--27. 1. " CUY0 ,Specifies the CUY coordinate" hexmask.long.word 0x08 0.--11. 1. " CUX0 ,Specifies the CUX coordinate" line.long 0x0C "CURSOR0TRANSPARENTCONTROL,Cursor0TransparentControl" bitfld.long 0x0C 8. " CUZT0 ,Controls the transparency mode" "Disabled,Enabled" hexmask.long.byte 0x0C 0.--7. 1. " CUTC0 ,Specifies Cursor 0 color data that should be treated as transparent" group.long 0x208++0x0F line.long 0x00 "CURSOR1PRIORITYMODE,Sets the priority of cursor display" bitfld.long 0x00 31. " CEN1 ,Enables/disables display of cursor 1" "Disabled,Enabled" bitfld.long 0x00 30. " SC1ENC1 ,Determines whether cursor1 is included in screen1 or not" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0ENC1 ,Determines whether cursor1 is included in screen0 or not" "Not included,Included" bitfld.long 0x00 1.--2. " CU1SIZ ,Sets Size of cursor 1" "128x128,64x64,32x32,16x16" textline " " bitfld.long 0x00 0. " CUO1 ,Sets the display priority of cursor 1 and the L1 layer" "Below,Above" line.long 0x04 "CURSOR1ORIGINADDRESS,Cursor1OriginAddress" line.long 0x08 "CURSOR1POSITION,Sets the display position coordinates (CUX1,CUY1) of cursor 1 in units of pixels" hexmask.long.word 0x08 16.--27. 1. " CUY1 ,Specifies the CUY coordinate" hexmask.long.word 0x08 0.--11. 1. " CUX1 ,Specifies the CUX coordinate" line.long 0x0C "CURSOR1TRANSPARENTCONTROL,Cursor1TransparentControl" bitfld.long 0x0C 8. " CUZT1 ,Controls the transparency mode" "Disabled,Enabled" hexmask.long.byte 0x0C 0.--7. 1. " CUTC1 ,Specifies Cursor 1 color data that should be treated as transparent" group.long 0x218++0x17 line.long 0x00 "L1COEFFICIENT0,Set color matrix of Layer 1" hexmask.long.word 0x00 16.--26. 1. " L1A12 ,11-bit signed fixed-point value" hexmask.long.word 0x00 0.--10. 1. " L1A11 ,11-bit signed fixed-point value" line.long 0x04 "L1COEFFICIENT1,Set color matrix of Layer 1" hexmask.long.word 0x04 16.--24. 1. " L1B1 ,9-bit signed integer" hexmask.long.word 0x04 0.--10. 1. " L1A13 ,11-bit signed fixed-point value" line.long 0x08 "L1COEFFICIENT2,Set color matrix of Layer 1" hexmask.long.word 0x08 16.--26. 1. " L1A22 ,11-bit signed fixed-point value" hexmask.long.word 0x08 0.--10. 1. " L1A21 ,11-bit signed fixed-point value" line.long 0x0C "L1COEFFICIENT3,Set color matrix of Layer 1" hexmask.long.word 0x0C 16.--24. 1. " L1B2 ,9-bit signed integer" hexmask.long.word 0x0C 0.--10. 1. " L1A23 ,11-bit signed fixed-point value" line.long 0x10 "L1COEFFICIENT4,Set color matrix of Layer 1" hexmask.long.word 0x10 16.--26. 1. " L1A32 ,11-bit signed fixed-point value" hexmask.long.word 0x10 0.--10. 1. " L1A31 ,11-bit signed fixed-point value" line.long 0x14 "L1COEFFICIENT5,Set color matrix of Layer 1" hexmask.long.word 0x14 16.--24. 1. " L1B3 ,9-bit signed integer" hexmask.long.word 0x14 0.--10. 1. " L1A33 ,11-bit signed fixed-point value" group.long 0x230++0x17 line.long 0x00 "L2COEFFICIENT0,Set color matrix of Layer 1" hexmask.long.word 0x00 16.--26. 1. " L2A12 ,11-bit signed fixed-point value" hexmask.long.word 0x00 0.--10. 1. " L2A11 ,11-bit signed fixed-point value" line.long 0x04 "L2COEFFICIENT1,Set color matrix of Layer 1" hexmask.long.word 0x04 16.--24. 1. " L2B1 ,9-bit signed integer" hexmask.long.word 0x04 0.--10. 1. " L2A13 ,11-bit signed fixed-point value" line.long 0x08 "L2COEFFICIENT2,Set color matrix of Layer 1" hexmask.long.word 0x08 16.--26. 1. " L2A22 ,11-bit signed fixed-point value" hexmask.long.word 0x08 0.--10. 1. " L2A21 ,11-bit signed fixed-point value" line.long 0x0C "L2COEFFICIENT3,Set color matrix of Layer 1" hexmask.long.word 0x0C 16.--24. 1. " L2B2 ,9-bit signed integer" hexmask.long.word 0x0C 0.--10. 1. " L2A23 ,11-bit signed fixed-point value" line.long 0x10 "L2COEFFICIENT4,Set color matrix of Layer 1" hexmask.long.word 0x10 16.--26. 1. " L2A32 ,11-bit signed fixed-point value" hexmask.long.word 0x10 0.--10. 1. " L2A31 ,11-bit signed fixed-point value" line.long 0x14 "L2COEFFICIENT5,Set color matrix of Layer 1" hexmask.long.word 0x14 16.--24. 1. " L2B3 ,9-bit signed integer" hexmask.long.word 0x14 0.--10. 1. " L2A33 ,11-bit signed fixed-point value" group.long 0x248++0x17 line.long 0x00 "L3COEFFICIENT0,Set color matrix of Layer 1" hexmask.long.word 0x00 16.--26. 1. " L3A12 ,11-bit signed fixed-point value" hexmask.long.word 0x00 0.--10. 1. " L3A11 ,11-bit signed fixed-point value" line.long 0x04 "L3COEFFICIENT1,Set color matrix of Layer 1" hexmask.long.word 0x04 16.--24. 1. " L3B1 ,9-bit signed integer" hexmask.long.word 0x04 0.--10. 1. " L3A13 ,11-bit signed fixed-point value" line.long 0x08 "L3COEFFICIENT2,Set color matrix of Layer 1" hexmask.long.word 0x08 16.--26. 1. " L3A22 ,11-bit signed fixed-point value" hexmask.long.word 0x08 0.--10. 1. " L3A21 ,11-bit signed fixed-point value" line.long 0x0C "L3COEFFICIENT3,Set color matrix of Layer 1" hexmask.long.word 0x0C 16.--24. 1. " L3B2 ,9-bit signed integer" hexmask.long.word 0x0C 0.--10. 1. " L3A23 ,11-bit signed fixed-point value" line.long 0x10 "L3COEFFICIENT4,Set color matrix of Layer 1" hexmask.long.word 0x10 16.--26. 1. " L3A32 ,11-bit signed fixed-point value" hexmask.long.word 0x10 0.--10. 1. " L3A31 ,11-bit signed fixed-point value" line.long 0x14 "L3COEFFICIENT5,Set color matrix of Layer 1" hexmask.long.word 0x14 16.--24. 1. " L3B3 ,9-bit signed integer" hexmask.long.word 0x14 0.--10. 1. " L3A33 ,11-bit signed fixed-point value" group.long 0x260++0x17 line.long 0x00 "L4COEFFICIENT0,Set color matrix of Layer 1" hexmask.long.word 0x00 16.--26. 1. " L4A12 ,11-bit signed fixed-point value" hexmask.long.word 0x00 0.--10. 1. " L4A11 ,11-bit signed fixed-point value" line.long 0x04 "L4COEFFICIENT1,Set color matrix of Layer 1" hexmask.long.word 0x04 16.--24. 1. " L4B1 ,9-bit signed integer" hexmask.long.word 0x04 0.--10. 1. " L4A13 ,11-bit signed fixed-point value" line.long 0x08 "L4COEFFICIENT2,Set color matrix of Layer 1" hexmask.long.word 0x08 16.--26. 1. " L4A22 ,11-bit signed fixed-point value" hexmask.long.word 0x08 0.--10. 1. " L4A21 ,11-bit signed fixed-point value" line.long 0x0C "L4COEFFICIENT3,Set color matrix of Layer 1" hexmask.long.word 0x0C 16.--24. 1. " L4B2 ,9-bit signed integer" hexmask.long.word 0x0C 0.--10. 1. " L4A23 ,11-bit signed fixed-point value" line.long 0x10 "L4COEFFICIENT4,Set color matrix of Layer 1" hexmask.long.word 0x10 16.--26. 1. " L4A32 ,11-bit signed fixed-point value" hexmask.long.word 0x10 0.--10. 1. " L4A31 ,11-bit signed fixed-point value" line.long 0x14 "L4COEFFICIENT5,Set color matrix of Layer 1" hexmask.long.word 0x14 16.--24. 1. " L4B3 ,9-bit signed integer" hexmask.long.word 0x14 0.--10. 1. " L4A33 ,11-bit signed fixed-point value" textline " " rgroup.long 0x300++0x07 line.long 0x00 "BUFFERROR,Buffer error register" bitfld.long 0x00 11. " LA[3]ERR ,Error status of LA3 FIFO" "Normal,Error" bitfld.long 0x00 10. " [2] ,Error status of LA2 FIFO" "Normal,Error" bitfld.long 0x00 9. " [1] ,Error status of LA1 FIFO" "Normal,Error" bitfld.long 0x00 8. " [0] ,Error status of LA0 FIFO" "Normal,Error" textline " " bitfld.long 0x00 7. " L[7]ERR ,Error status of L7 FIFO" "Normal,Error" bitfld.long 0x00 6. " [6] ,Error status of L6 FIFO" "Normal,Error" bitfld.long 0x00 5. " [5] ,Error status of L5 FIFO" "Normal,Error" bitfld.long 0x00 4. " [4] ,Error status of L4 FIFO" "Normal,Error" textline " " bitfld.long 0x00 3. " [3] ,Error status of L3 FIFO" "Normal,Error" bitfld.long 0x00 2. " [2] ,Error status of L2 FIFO" "Normal,Error" bitfld.long 0x00 1. " [1] ,Error status of L1 FIFO" "Normal,Error" bitfld.long 0x00 0. " [0] ,Error status of L0 FIFO" "Normal,Error" textline " " line.long 0x04 "BUFFERRIE,Enable to generate interrupt signal of buffer error. Emerald-P and -L(MP) only" bitfld.long 0x04 0. " BUFFERRIE ,BuffErrIE" "Disabled,Enabled" group.long 0x400++0x3 line.long 0x00 "PALETTE0,Memory mapped RAM for Palette0" button "PALETTE0" "d (ad:0xD0800000+0x400)--(ad:0xD0800000+0x7FF) /long" group.long 0x800++0x3 line.long 0x00 "PALETTE1,Memory mapped RAM for Palette1" button "PALETTE1" "d (ad:0xD0800000+0x800)--(ad:0xD0800000+0xBFF) /long" group.long 0xC00++0x3 line.long 0x00 "PALETTE2,Memory mapped RAM for Palette2" button "PALETTE2" "d (ad:0xD0800000+0xC00)--(ad:0xD0800000+0xFFF) /long" group.long 0x1000++0x3 line.long 0x00 "PALETTE3,Memory mapped RAM for Palette3" button "PALETTE3" "d (ad:0xD0800000+0x1000)--(ad:0xD0800000+0x13FF) /long" group.long 0x1400++0x3 line.long 0x00 "CLUTDATA,Memory mapped RAM for CLUT" button "CLUTDATA" "d (ad:0xD0800000+0x1400)--(ad:0xD0800000+0x17FF) /long" group.long 0x1800++0x03 line.long 0x00 "SOFTWARERESETENABLE,SW reset" bitfld.long 0x00 0. " SOFTRESET ,Executes a software reset" "No reset,Reset" width 0xb tree.end tree "Display 1" base ad:0xD0810000 width 25. group.long 0x00++0x03 line.long 0x00 "DISPLAYENABLE,Display Enable register" bitfld.long 0x00 0. " DEN ,DisplayEnable" "Disabled,Enabled" if (((per.l(ad:0xD0810000+0x04))&0x01)==0x01) group.long 0x04++0x03 line.long 0x00 "REGISTERUPDATEMODE,Defines the register update mode" bitfld.long 0x00 29. " RUMLAY_[0] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 28. " [1] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 27. " [2] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 26. " [3] ,Defines update mode" "Direct,Synchronous" textline " " bitfld.long 0x00 25. " [4] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 24. " [5] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 23. " [6] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 22. " [7] ,Defines update mode" "Direct,Synchronous" textline " " bitfld.long 0x00 21. " [8] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 20. " [9] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 19. " [10] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 18. " [11] ,Defines update mode" "Direct,Synchronous" textline " " bitfld.long 0x00 17. " [12] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 16. " [13] ,Defines update mode" "Direct,Synchronous" textline " " bitfld.long 0x00 1. " RUM ,Selects a mode during which register values are updated in sync with vertical synchronization globally" "Off,On" bitfld.long 0x00 0. " RUMSEL ,Selects the global register update mode" "Global,Per layer" else group.long 0x04++0x03 line.long 0x00 "REGISTERUPDATEMODE,Defines the register update mode" textline " " textline " " textline " " textline " " bitfld.long 0x00 1. " RUM ,Selects a mode during which register values are updated in sync with vertical synchronization globally" "Off,On" bitfld.long 0x00 0. " RUMSEL ,Selects the global register update mode" "Global,Per layer" endif textline " " group.long 0x08++0x1B line.long 0x00 "REGISTERUPDATESELECTION,Set the layers for synchronous update by vertical synchronization with RUFlag" sif (cpu()=="MB86R11F") hexmask.long.word 0x00 16.--29. 1. " RUFLAY ,Defines independently for each layer" textline " " endif bitfld.long 0x00 0. " RUFSEL ,Selects global update for all layers or independent update per layer" "Global,Per layer" textline " " line.long 0x04 "REGISTERUPDATEFLAG,Triggers the register update at next vertical synchronization" bitfld.long 0x04 29. " RUFLAY[13] ,Bit 13 layer update" "No update,Update" bitfld.long 0x04 28. " [12] ,Bit 12 layer update" "No update,Update" bitfld.long 0x04 27. " [11] ,Bit 11 layer update" "No update,Update" bitfld.long 0x04 26. " [10] ,Bit 10 layer update" "No update,Update" textline " " bitfld.long 0x04 25. " [9] ,Bit 9 layer update" "No update,Update" bitfld.long 0x04 24. " [8] ,Bit 8 layer update" "No update,Update" bitfld.long 0x04 23. " [7] ,Bit 7 layer update" "No update,Update" bitfld.long 0x04 22. " [6] ,Bit 6 layer update" "No update,Update" textline " " bitfld.long 0x04 21. " [5] ,Bit 5 layer update" "No update,Update" bitfld.long 0x04 20. " [4] ,Bit 4 layer update" "No update,Update" bitfld.long 0x04 19. " [3] ,Bit 3 layer update" "No update,Update" bitfld.long 0x04 18. " [2] ,Bit 2 layer update" "No update,Update" textline " " bitfld.long 0x04 17. " [1] ,Bit 1 layer update" "No update,Update" bitfld.long 0x04 16. " [0] ,Bit 0 layer update" "No update,Update" textline " " bitfld.long 0x04 0. " RUFLAG ,Instruction is issued to update selected layers" "Initial state/update completed,Vertical synchronization triggered" textline " " line.long 0x08 "DCLKCONFIG,Defines the pixel output clock" bitfld.long 0x08 25. " DPIXMODE ,Set Dual Pixel mode" "Not used,Used" bitfld.long 0x08 24. " RSDSMODE ,Set RSDS mode" "Not used,Used" sif (cpu()=="MB86R11F") bitfld.long 0x08 18.--22. " DCKDEL ,Defines an additional delay in units of the reference clock" "No additional delay,,+1 reference clock,,+2 reference clock,,+3 reference clock,,+4 reference clock,,+5 reference clock,,+6 reference clock,,+7 reference clock,,+8 reference clock,,+9 reference clock,,+10 reference clock,,+11 reference clock,,+12 reference clock,,+13 reference clock,,+14 reference clock,,+15 reference clock," else bitfld.long 0x08 18.--22. " DCKDEL ,Defines an additional delay in units of the reference clock" "No additional delay,,+2 reference clock,,+3 reference clock,,+4 reference clock,,+5 reference clock,,+6 reference clock,,+7 reference clock,,+8 reference clock,,+9 reference clock,,+10 reference clock,,+11 reference clock,,+12 reference clock,,+13 reference clock,,+14 reference clock,,+15 reference clock,,+16 reference clock," endif textline " " bitfld.long 0x08 17. " DCKDELEN ,Display clock delay" "Disabled,Enabled" bitfld.long 0x08 16. " DCKINV ,Inversion of display clock" "Not inverted,Inverted" bitfld.long 0x08 9.--14. " SC ,Divides the display reference clock by the set ratio for dot clocks generation" "Not divide,,,Divide the clock by 4,Divide the clock by 5,,,Divide the clock by 8,,,,,Divide the clock by 13,,,Divide the clock by 16,,,,,Divide the clock by 21,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,Divide the clock by 53,,,,,,,,,,Divide the clock by 63,Divide the clock by 64" textline " " bitfld.long 0x08 8. " DCSEL ,Selects the frequency of the reference input clock" "800/1066 MHz,Low" bitfld.long 0x08 1. " ENDCOP ,Sets the display clock output pin to high impedance" "Don't switch,Switch" bitfld.long 0x08 0. " CKS ,Selects the reference clock" "PLL,DCLKI" line.long 0x0C "DISPLAYPORTCONFIG,Configuration of ports for synchronization signals" bitfld.long 0x0C 21. " TCONDELAY[5] ,Change TCON coutput timing of display" "No delay,Delay" bitfld.long 0x0C 20. " [4] ,Change TCON coutput timing of display" "No delay,Delay" bitfld.long 0x0C 19. " [3] ,Change TCON coutput timing of display" "No delay,Delay" bitfld.long 0x0C 18. " [2] ,Change TCON coutput timing of display" "No delay,Delay" bitfld.long 0x0C 17. " [1] ,Change TCON coutput timing of display" "No delay,Delay" bitfld.long 0x0C 16. " [0] ,Change TCON coutput timing of display" "No delay,Delay" textline " " bitfld.long 0x0C 3. " SYOUTEN ,Switch display YSNC and VSYNC pin direction" "INPUT Ports,OUTPUT Ports" bitfld.long 0x0C 1. " SF ,Sets synchronization active value" "Low active,High active" bitfld.long 0x0C 0. " ESY ,Enables external synchronization mode" "Disabled,Enabled" line.long 0x10 "DISPLAYRESOLUTION,Configuration of display resolution" hexmask.long.word 0x10 16.--27. 1. " VTR ,Specifies the vertical total line count" hexmask.long.word 0x10 0.--11. 1. " HTP ,Specifies the horizontal total pixel count" line.long 0x14 "ACTIVEAREA,Configuration of active video area" hexmask.long.word 0x14 16.--27. 1. " VDP ,Specifies the vertical display period in units of lines" hexmask.long.word 0x14 0.--11. 1. " HDP ,Specifies the horizontal display boundary in units of pixel" textline " " width 31. line.long 0x18 "HORSYNCHTIMINGCONFIGURATION,Configuration of the horizontal synchronization output timing" hexmask.long.byte 0x18 16.--23. 1. " HSW ,Specifies the pulse width of the horizontal synchronization signal in units of pixel" hexmask.long.word 0x18 0.--11. 1. " HSP ,Specifies the position of the horizontal synchronization signal in units of pixel" group.long 0x24++0x23 line.long 0x00 "VERSYNCHTIMINGCONFIGURATION,Configuration of the vertical synchronization output timing" bitfld.long 0x00 31. " VSWH ,Extends the pulse width of the vertical synchronization signal by half of a line" "0,1" hexmask.long.byte 0x00 16.--21. 1. " VSW ,Specifies the pulse width of the vertical synchronization signal in units of pixel clocks" textline " " hexmask.long.word 0x00 0.--11. 1. " VSP ,Specifies the position of the vertical synchronization signal in units of lines" line.long 0x04 "DISPLAYOUTPUTCONFIG,Configuration of output modes" bitfld.long 0x04 4. " DCKEDGE ,Defines the DCLK OUTPUT edge mode" "No equalization,Equalization" bitfld.long 0x04 3. " EEQ ,Sets the equalization pulse mode for the CSYNC signal" "EEQOFF,EEQON" textline " " bitfld.long 0x04 2. " POM ,Parallel Operation Mode" "Disabled,Enabled" bitfld.long 0x04 0.--1. " SYNC ,Sets display output mode" "NOINTLM,INTLM,,INTLVM" line.long 0x08 "MULTIDISPLAYDUALVIEWSETUP,Configuration of dual view processing" bitfld.long 0x08 31. " MDEN ,Enable multi-display functionality" "Disabled,Enabled" bitfld.long 0x08 2. " DVPATTERN ,Control the re-ordering between different lines" "Disabled,Enabled" textline " " bitfld.long 0x08 1. " DVDTSW ,Left and Right screen swapping" "Don't swap,Swap" bitfld.long 0x08 0. " DVEN ,DualView Enable" "Disabled,Enabled" line.long 0x0C "CHROMAKEYCONTROL,Configuration of chroma keying" bitfld.long 0x0C 31. " KCS ,Selects whether the display output color" "Display,L0 layer" bitfld.long 0x0C 30. " KYEN ,Enables chroma-key processing" "Disabled,Enabled" textline " " hexmask.long.tbyte 0x0C 0.--23. 1. " KYC ,Sets the key color used to perform chroma-key processing" line.long 0x10 "CLUTCONTROL,Enables/Disables the Color Lookup table" bitfld.long 0x10 31. " CLUTEN ,Enable Color Look Up" "Disabled,Enabled" line.long 0x14 "DITHERCONTROL,Configures the Dither unit" bitfld.long 0x14 4. " DITHMS ,Select mode for dithering" "Temporal dithering,Spatial dithering" bitfld.long 0x14 3. " DITHRS ,Sets dither range" "Add '1' to lower bits,Add '1' to higher bits" textline " " bitfld.long 0x14 1.--2. " DITHFS ,Select output format for dithering" "10x10x10->8x8x8,10x10x10->7x7x7,10x10x10->6x6x6,10x10x10->5x6x5" bitfld.long 0x14 0. " DITHEN ,Enable Dithering" "Disabled,Enabled" line.long 0x18 "DISPLAYBACKGROUNDCOLOR,This color is displayed on screen areas that are not included in any display window" bitfld.long 0x18 31. " DBGEN ,Enable the background color" "Not blended,Blended" hexmask.long.byte 0x18 16.--23. 1. " DBGR ,Specifies the red level of the background color" textline " " hexmask.long.byte 0x18 8.--15. 1. " DBGG ,Specifies the green level of the background color" hexmask.long.byte 0x18 0.--7. 1. " DBGB ,Specifies the blue level of the background color" line.long 0x20 "DISPLAYLAYERSELECT,Defines the layer superimposition order" textline " " bitfld.long 0x20 28.--31. " DLS_[7] ,Selects the bottom layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 24.--27. " [6] ,Selects the seventh layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 20.--23. " [5] ,Selects the sixth layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 16.--19. " [4] ,Selects the fifth layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" textline " " bitfld.long 0x20 12.--15. " [3] ,Selects the fourth layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 8.--11. " [2] ,Selects the third layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 4.--7. " [1] ,Selects the second layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 0.--3. " [0] ,Selects the top layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" textline " " group.long 0x44++0x23 line.long 0x00 "COMPATIBILITYMODE,Handles RUBY compatibility" bitfld.long 0x00 4. " RUBYMD ,Ruby Mode" "Ruby mode off,Ruby mode on" bitfld.long 0x00 0. " AH ,Address high keep this bit zero" "0,1" line.long 0x04 "L0LAYERMODE,L0LayerMode" bitfld.long 0x04 31. " L0E ,Enables L0 layer display" "Disabled,Enabled" bitfld.long 0x04 30. " SC1EN0 ,SC1en0" "Not included,Included" textline " " bitfld.long 0x04 29. " SC0EN0 ,SC0en0" "Not included,Included" hexmask.long.byte 0x04 16.--23. 1. " L0W ,Sets the memory width (stride) of the L0 layer logical frame in units of 64 bytes" textline " " hexmask.long.word 0x04 0.--11. 1. " L0H ,Specifies the height of the L0 layer logical frame in units of pixels" line.long 0x08 "L0COLORMODE,L0ColorMode" bitfld.long 0x08 8.--10. " L0CMODE ,Sets the L0 layer color mode" "16b/p ARGB mode,24b/p ARGB mode,16b/p RGBA mode,24b/p RGBA mode,24b/p ABGR mode,Indirect color 8 b/p mode,16b/p RGB565 mode," bitfld.long 0x08 0.--3. " L0PB ,Indicates the value added to the index when using the L0 layer palette" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x0C "L0ORIGINADDRESS,L0OriginAddress" line.long 0x10 "L0DISPLAYADDRESS,L0DisplayAddress" line.long 0x14 "L0DISPLAYPOSITION,Sets the display position coordinates (DX,DY) of the L0 layer" hexmask.long.word 0x14 16.--27. 1. " L0DY ,Specifies the DY coordinate" hexmask.long.word 0x14 0.--11. 1. " L0DX ,Specifies the DX coordinate" line.long 0x18 "L0WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the L0 layer window" hexmask.long.word 0x18 16.--27. 1. " L0WY ,Specifies theWY coordinate" hexmask.long.word 0x18 0.--11. 1. " L0WX ,Specifies the WX coordinate" line.long 0x1C "L0WINDOWSIZE,Sets the size of the L0 layer window" hexmask.long.word 0x1C 16.--27. 1. " L0WH ,Specifies the height" hexmask.long.word 0x1C 0.--11. 1. " L0WW ,Specifies the width in units of pixels" line.long 0x20 "L0READSKIPMODE,Controls read skip operation of layer L0" bitfld.long 0x20 15. " L0SE ,Specifies whether or not to enable the read skip function" "Disabled,Enabled" hexmask.long.word 0x20 0.--8. 1. " L0PRE ,Specifies whether or not to perform a read operation for the partition corresponding to each bit" group.long 0x68++0x0F line.long 0x00 "L0PARTITIONX,Specifies two X coordinates which split the L0 layer when performing a read skip" hexmask.long.word 0x00 16.--27. 1. " L0PX1 ,Specifies the second X coordinate for read skip partition" hexmask.long.word 0x00 0.--11. 1. " L0PX0 ,Specifies the first X coordinate for read skip partition" line.long 0x04 "L0PARTITIONY,Specifies two Y coordinates which split the L0 layer when performing a read skip" hexmask.long.word 0x04 16.--27. 1. " L0PY1 ,Specifies the second Y coordinate for read skip partition" hexmask.long.word 0x04 0.--11. 1. " L0PY0 ,Specifies the first Y coordinate for read skip partition" line.long 0x08 "L0BLEND,Configures blending operation of Layer 0" bitfld.long 0x08 16.--18. " L0BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x08 14. " L0BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x08 13. " L0BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x08 11.--12. " L0AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x08 10. " L0AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x08 9. " L0AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x08 0.--8. 1. " L0BR ,Sets the blend ratio" line.long 0x0C "L0TRANSPARENCYCONTROL,Controls transparency processing of Layer 0" bitfld.long 0x0C 31. " L0ZT ,Enables transparent processing for Layer L0" "Disabled,Enabled" hexmask.long.tbyte 0x0C 0.--23. 1. " L0TC ,Sets the color value (code) treated as transparent color for L0 layer" group.long 0x78++0x0B line.long 0x00 "L1LAYERMODE,1LayerMode" bitfld.long 0x00 31. " L1E ,Enables L1 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1en1 ,SC1en1" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0EN1 ,SC0en1" "Not included,Included" bitfld.long 0x00 20. " L1ENBWAUTO ,Set an automatic video capture operation mode when L1CS is in capture mode" "No automatic mode,Automatic Buffer managment" textline " " bitfld.long 0x00 19. " L1YC ,Sets the L1 layer color format" "RGB mode,YC mode" bitfld.long 0x00 18. " L1CS ,Sets whether to use the L1 layer as a normal display layer or as a video capture layer" "Normal mode,Video Capture mode" textline " " bitfld.long 0x00 17. " L1INTL ,Sets a video capture operation mode" "Normal mode,WEAVE mode" bitfld.long 0x00 16. " L1VMAG ,Enables capture image upscaling" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 0.--7. 1. " L1W ,Sets the memory width (stride) of the L1 layer logical frame in units of 64 bytes" line.long 0x04 "L1COLORMODE,L1ColorMode" bitfld.long 0x04 8.--10. " L1CMODE ,Sets the L1 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,16b/p RGB565 mode," bitfld.long 0x04 0.--3. " L1PB ,Indicates the value to be added to the index when drawing the L1 layer palette" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "L1DISPLAYADDRESS,Sets the display window origin address of the L1 layer" rgroup.long 0x84++0x07 line.long 0x00 "CAPTURE1BUFFERDISPLAYADDRESS0,Starting address of the displayed capture image" line.long 0x04 "CAPTURE1BUFFERDISPLAYADDRESS1,This register indicates the starting address of an even field of the capture screen" group.long 0x8C++0x07 line.long 0x00 "L1WINDOWPOSITION,L1WindowPosition" hexmask.long.word 0x00 16.--27. 1. " L1WY ,Sets the display position coordinates (WY) of the L1 layer window" hexmask.long.word 0x00 0.--11. 1. " L1WX ,Sets the display position coordinates (WX) of the L1 layer window" line.long 0x04 "L1WINDOWSIZE,L1WindowSize" hexmask.long.word 0x04 16.--27. 1. " L1WH ,Sets the size of the L1 layer window. Specifies the height" hexmask.long.word 0x04 0.--11. 1. " L1WW ,Sets the size of the L1 layer window.Specifies the width in units of pixels" group.long 0x9C++0x07 line.long 0x00 "L1BLEND,Configures blending operation of Layer 1" bitfld.long 0x00 16.--18. " L1BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x00 14. " L1BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x00 13. " L1BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x00 11.--12. " L1AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x00 10. " L1AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x00 9. " L1AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x00 0.--8. 1. " L1BR ,Sets the blend ratio" line.long 0x04 "L1TRANSPARENCYCONTROL,Controls transparency processing of Layer 1" bitfld.long 0x04 31. " L1ZT ,Enables transparent processing for Layer L1" "Disabled,Enabled" hexmask.long.tbyte 0x04 0.--23. 1. " L1TC ,Sets the color value (code) treated as transparent color for L1 layer" group.long 0xA4++0x1B line.long 0x00 "L2LAYERMODE,2LayerMode" bitfld.long 0x00 31. " L2E ,Enables L2 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1en2 ,SC1en2" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0EN2 ,SC0en2" "Not included,Included" bitfld.long 0x00 20. " L2ENBWAUTO ,Set an automatic video capture operation mode when L2CS is in capture mode" "No automatic mode,Automatic Buffer managment" textline " " bitfld.long 0x00 19. " L2YC ,Sets the L2 layer color format" "RGB mode,YC mode" bitfld.long 0x00 18. " L2CS ,Sets whether to use the L2 layer as a normal display layer or as a video capture layer" "Normal mode,Video Capture mode" textline " " bitfld.long 0x00 17. " L2INTL ,Sets a video capture operation mode" "Normal mode,WEAVE mode" bitfld.long 0x00 16. " L2VMAG ,Enable capture image upscaling" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 0.--7. 1. " L2W ,Sets the memory width (stride) of the L2 layer logical frame in units of 64 bytes" line.long 0x04 "L2COLORMODE,L2ColorMode" bitfld.long 0x04 8.--10. " L2CMODE ,Sets the L2 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,16b/p RGB565 mode," bitfld.long 0x04 0.--3. " L2PB ,Indicates the value to be added to the index when drawing the L2 layer palette" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "L2DISPLAYADDRESS,Sets the display window origin address of the L2 layer" line.long 0x0C "CAPTURE2BUFFERDISPLAYADDRESS0,Starting address of the displayed capture image" line.long 0x10 "CAPTURE2BUFFERDISPLAYADDRESS1,This register indicates the starting address of an even field of the capture screen" line.long 0x14 "L2WINDOWPOSITION,L2WindowPosition" hexmask.long.word 0x14 16.--27. 1. " L2WY ,Sets the display position coordinates (WY) of the L2 layer window" hexmask.long.word 0x14 0.--11. 1. " L2WX ,Sets the display position coordinates (WX) of the L2 layer window" line.long 0x18 "L2WINDOWSIZE,L2WindowSize" hexmask.long.word 0x18 16.--27. 1. " L2WH ,Sets the size of the L2 layer window. Specifies the height" hexmask.long.word 0x18 0.--11. 1. " L2WW ,Sets the size of the L2 layer window.Specifies the width in units of pixels" group.long 0xC8++0x07 line.long 0x00 "L2BLEND,Configures blending operation of Layer 2" bitfld.long 0x00 16.--18. " L2BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x00 14. " L2BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x00 13. " L2BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x00 11.--12. " L2AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x00 10. " L2AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x00 9. " L2AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x00 0.--8. 1. " L2BR ,Sets the blend ratio" line.long 0x04 "L2TRANSPARENCYCONTROL,Controls transparency processing of Layer 2" bitfld.long 0x04 31. " L2ZT ,Enables transparent processing for Layer L2" "Disabled,Enabled" hexmask.long.tbyte 0x04 0.--23. 1. " L2TC ,Sets the color value (code) treated as transparent color for L2 layer" group.long 0xD0++0x1B line.long 0x00 "L3LAYERMODE,3LayerMode" bitfld.long 0x00 31. " L3E ,Enables L3 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1en3 ,SC1en3" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0EN3 ,SC0en3" "Not included,Included" bitfld.long 0x00 20. " L3ENBWAUTO ,Set an automatic video capture operation mode when L3CS is in capture mode" "No automatic mode,Automatic Buffer managment" textline " " bitfld.long 0x00 19. " L3YC ,Sets the L3 layer color format" "RGB mode,YC mode" bitfld.long 0x00 18. " L3CS ,Sets whether to use the L3 layer as a normal display layer or as a video capture layer" "Normal mode,Video Capture mode" textline " " bitfld.long 0x00 17. " L3INTL ,Sets a video capture operation mode" "Normal mode,WEAVE mode" bitfld.long 0x00 16. " L3VMAG ,Enable capture image upscaling" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 0.--7. 1. " L3W ,Sets the memory width (stride) of the L3layer logical frame in units of 64 bytes" line.long 0x04 "L3COLORMODE,L3ColorMode" bitfld.long 0x04 8.--10. " L3CMODE ,Sets the L3 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,16b/p RGB565 mode," bitfld.long 0x04 0.--3. " L3PB ,Indicates the value to be added to the index when drawing the L3 layer palette" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "L3DISPLAYADDRESS,Sets the display window origin address of the L3 layer" line.long 0x0C "CAPTURE3BUFFERDISPLAYADDRESS0,Starting address of the displayed capture image" line.long 0x10 "CAPTURE3BUFFERDISPLAYADDRESS1,This register indicates the starting address of an even field of the capture screen" line.long 0x14 "L3WINDOWPOSITION,L3WindowPosition" hexmask.long.word 0x14 16.--27. 1. " L3WY ,Sets the display position coordinates (WY) of the L3 layer window" hexmask.long.word 0x14 0.--11. 1. " L3WX ,Sets the display position coordinates (WX) of the L3 layer window" line.long 0x18 "L3WINDOWSIZE,L3WindowSize" hexmask.long.word 0x18 16.--27. 1. " L3WH ,Sets the size of the L3 layer window. Specifies the height" hexmask.long.word 0x18 0.--11. 1. " L3WW ,Sets the size of the L3 layer window.Specifies the width in units of pixels" group.long 0xF4++0x07 line.long 0x00 "L3BLEND,Configures blending operation of Layer 3" bitfld.long 0x00 16.--18. " L3BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x00 14. " L3BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x00 13. " L3BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x00 11.--12. " L3AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x00 10. " L3AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x00 9. " L3AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x00 0.--8. 1. " L3BR ,Sets the blend ratio" line.long 0x04 "L3TRANSPARENCYCONTROL,Controls transparency processing of Layer 3" bitfld.long 0x04 31. " L3ZT ,Enables transparent processing for Layer L3" "Disabled,Enabled" hexmask.long.tbyte 0x04 0.--23. 1. " L3TC ,Sets the color value (code) treated as transparent color for L3 layer" group.long 0xFC++0x03 line.long 0x00 "L4LAYERMODE,4LayerMode" bitfld.long 0x00 31. " L4E ,Enables L4 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1en4 ,SC1en4" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0EN4 ,SC0en4" "Not included,Included" bitfld.long 0x00 20. " L4ENBWAUTO ,Set an automatic video capture operation mode when L4CS is in capture mode" "No automatic mode,Automatic Buffer managment" textline " " bitfld.long 0x00 19. " L4YC ,Sets the L4 layer color format" "RGB mode,YC mode" bitfld.long 0x00 18. " L4CS ,Sets whether to use the L4 layer as a normal display layer or as a video capture layer" "Normal mode,Video Capture mode" textline " " bitfld.long 0x00 17. " L4INTL ,Sets a video capture operation mode" "Normal mode,WEAVE mode" bitfld.long 0x00 16. " L4VMAG ,Enable capture image upscaling" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 0.--7. 1. " L4W ,Sets the memory width (stride) of the L4layer logical frame in units of 64 bytes" group.long 0x100++0x17 line.long 0x00 "L4COLORMODE,L4ColorMode" bitfld.long 0x00 8.--10. " L4CMODE ,Sets the L4 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,16b/p RGB565 mode," line.long 0x04 "L4DISPLAYADDRESS,Sets the display window origin address of the L4 layer" line.long 0x08 "CAPTURE4BUFFERDISPLAYADDRESS0,Starting address of the displayed capture image" line.long 0x0C "CAPTURE4BUFFERDISPLAYADDRESS1,This register indicates the starting address of an even field of the capture screen" line.long 0x10 "L4WINDOWPOSITION,L4WindowPosition" hexmask.long.word 0x10 16.--27. 1. " L4WY ,Sets the display position coordinates (WY) of the L4 layer window" hexmask.long.word 0x10 0.--11. 1. " L4WX ,Sets the display position coordinates (WX) of the L4 layer window" line.long 0x14 "L4WINDOWSIZE,L4WindowSize" hexmask.long.word 0x14 16.--27. 1. " L4WH ,Sets the size of the L4 layer window. Specifies the height" hexmask.long.word 0x14 0.--11. 1. " L4WW ,Sets the size of the L4 layer window.Specifies the width in units of pixels" group.long 0x120++0x07 line.long 0x00 "L4BLEND,Configures blending operation of Layer 4" bitfld.long 0x00 16.--18. " L4BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x00 14. " L4BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x00 13. " L4BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x00 11.--12. " L4AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x00 10. " L4AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x00 9. " L4AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x00 0.--8. 1. " L4BR ,Sets the blend ratio" line.long 0x04 "L4TRANSPARENCYCONTROL,Controls transparency processing of Layer 4" bitfld.long 0x04 31. " L4ZT ,Enables transparent processing for Layer L4" "Disabled,Enabled" hexmask.long.tbyte 0x04 0.--23. 1. " L4TC ,Sets the color value (code) treated as transparent color for L4 layer" group.long 0x128++0x3 line.long 0x00 "L5LAYERMODE,5LayerMode" bitfld.long 0x00 31. " L5E ,Enables L5 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1EN5 ,SC1en5" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0EN5 ,SC0en5" "Not included,Included" hexmask.long.byte 0x00 16.--23. 1. " L5W ,Sets the memory width (stride) of the L5 layer logical frame in units of 64 bytes" textline " " hexmask.long.word 0x00 0.--11. 1. " L5H ,Specifies the height of the L5 layer logical frame in units of pixels" group.long 0x12C++0x17 line.long 0x00 "L5COLORMODE,L5ColorMode" bitfld.long 0x00 8.--10. " L5CMODE ,Sets the L5 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,16b/p RGB565 mode," line.long 0x04 "L5ORIGINADDRESS,Sets the logical frame origin address of L5 layer" line.long 0x08 "L5DISPLAYADDRESS,Sets the display origin address of L5 layer" line.long 0x0C "L5DISPLAYPOSITION,L5DisplayPosition" line.long 0x10 "L5WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the L5 layer window" hexmask.long.word 0x10 16.--27. 1. " L5WY ,Sets the display position coordinates (WY) of the L5 layer window" hexmask.long.word 0x10 0.--11. 1. " L5WX ,Sets the display position coordinates (WX) of the L5 layer window" line.long 0x14 "L5WINDOWSIZE,L5WindowSize" hexmask.long.word 0x14 16.--27. 1. " L5WH ,Sets the size of the L5 layer window. Specifies the height" hexmask.long.word 0x14 0.--11. 1. " L5WW ,Sets the size of the L5 layer window.Specifies the width in units of pixels" group.long 0x144++0x13 line.long 0x00 "L5READSKIPMODE,Controls read skip operation of layer L5" bitfld.long 0x00 15. " L0SE ,Specifies whether or not to enable the read skip function" "Disabled,Enabled" hexmask.long.word 0x00 0.--8. 1. " L0PRE ,Specifies whether or not to perform a read operation for the partition corresponding to each bit" line.long 0x04 "L5PARTITIONX,Specifies two X coordinates which split the L5 layer when performing a read skip" hexmask.long.word 0x04 16.--27. 1. " L0PX1 ,Specifies the second X coordinate for read skip partition" hexmask.long.word 0x04 0.--11. 1. " L0PX0 ,Specifies the first X coordinate for read skip partition" line.long 0x08 "L5PARTITIONY,Specifies two Y coordinates which split the L5 layer when performing a read skip" hexmask.long.word 0x08 16.--27. 1. " L0PY1 ,Specifies the second Y coordinate for read skip partition" hexmask.long.word 0x08 0.--11. 1. " L0PY0 ,Specifies the first Y coordinate for read skip partition" line.long 0x0C "L5BLEND,Configures blending operation of Layer 5" bitfld.long 0x0C 16.--18. " L5BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x0C 14. " L5BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x0C 13. " L5BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x0C 11.--12. " L5AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x0C 10. " L5AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x0C 9. " L5AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x0C 0.--8. 1. " L5BR ,Sets the blend ratio" line.long 0x10 "L5TRANSPARENCYCONTROL,Controls transparency processing of Layer 5" bitfld.long 0x10 31. " L5ZT ,Enables transparent processing for Layer L5" "Disabled,Enabled" hexmask.long.tbyte 0x10 0.--23. 1. " L5TC ,Sets the color value (code) treated as transparent color for L5 layer" group.long 0x158++0x3 line.long 0x00 "L6LAYERMODE,6LayerMode" bitfld.long 0x00 31. " L5E ,Enables L6 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1en6 ,SC1en6" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0EN6 ,SC0en6" "Not included,Included" hexmask.long.byte 0x00 16.--23. 1. " L6W ,Sets the memory width (stride) of the L6 layer logical frame in units of 64 bytes" textline " " hexmask.long.word 0x00 0.--11. 1. " L6H ,Specifies the height of the L6 layer logical frame in units of pixels" group.long 0x15C++0x17 line.long 0x00 "L6COLORMODE,L6ColorMode" bitfld.long 0x00 8.--10. " L6CMODE ,Sets the L6 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,16b/p RGB565 mode," line.long 0x04 "L6ORIGINADDRESS,Sets the logical frame origin address of L6 layer" line.long 0x08 "L6DISPLAYADDRESS,Sets the display origin address of L6 layer" line.long 0x0C "L6DISPLAYPOSITION,L6DisplayPosition" line.long 0x10 "L6WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the L6 layer window" hexmask.long.word 0x10 16.--27. 1. " L6WY ,Sets the display position coordinates (WY) of the L6 layer window" hexmask.long.word 0x10 0.--11. 1. " L6WX ,Sets the display position coordinates (WX) of the L6 layer window" line.long 0x14 "L6WINDOWSIZE,L6WindowSize" hexmask.long.word 0x14 16.--27. 1. " L6WH ,Sets the size of the L6 layer window. Specifies the height" hexmask.long.word 0x14 0.--11. 1. " L6WW ,Sets the size of the L6 layer window.Specifies the width in units of pixels" group.long 0x174++0x13 line.long 0x00 "L6READSKIPMODE,Controls read skip operation of layer L6" bitfld.long 0x00 15. " L6SE ,Specifies whether or not to enable the read skip function" "Disabled,Enabled" hexmask.long.word 0x00 0.--8. 1. " L6PRE ,Specifies whether or not to perform a read operation for the partition corresponding to each bit" line.long 0x04 "L6PARTITIONX,Specifies two X coordinates which split the L6 layer when performing a read skip" hexmask.long.word 0x04 16.--27. 1. " L6PX1 ,Specifies the second X coordinate for read skip partition" hexmask.long.word 0x04 0.--11. 1. " L6PX0 ,Specifies the first X coordinate for read skip partition" line.long 0x08 "L6PARTITIONY,Specifies two Y coordinates which split the L6 layer when performing a read skip" hexmask.long.word 0x08 16.--27. 1. " L6PY1 ,Specifies the second Y coordinate for read skip partition" hexmask.long.word 0x08 0.--11. 1. " L6PY0 ,Specifies the first Y coordinate for read skip partition" line.long 0x0C "L6BLEND,Configures blending operation of Layer 6" bitfld.long 0x0C 16.--18. " L6BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x0C 14. " L6BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x0C 13. " L6BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x0C 11.--12. " L6AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x0C 10. " L6AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x0C 9. " L6AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x0C 0.--8. 1. " L6BR ,Sets the blend ratio" line.long 0x10 "L6TRANSPARENCYCONTROL,Controls transparency processing of Layer 6" bitfld.long 0x10 31. " L6ZT ,Enables transparent processing for Layer L6" "Disabled,Enabled" hexmask.long.tbyte 0x10 0.--23. 1. " L6TC ,Sets the color value (code) treated as transparent color for L6 layer" group.long 0x188++0x3 line.long 0x00 "L7LAYERMODE,7LayerMode" bitfld.long 0x00 31. " L7E ,Enables L7 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1EN7 ,SC1en6" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0EN7 ,SC0en7" "Not included,Included" hexmask.long.byte 0x00 16.--23. 1. " L7W ,Sets the memory width (stride) of the L7 layer logical frame in units of 64 bytes" textline " " hexmask.long.word 0x00 0.--11. 1. " L7H ,Specifies the height of the L7 layer logical frame in units of pixels" group.long 0x18C++0x17 line.long 0x00 "L7COLORMODE,L7ColorMode" bitfld.long 0x00 8.--10. " L7CMODE ,Sets the L7 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,16b/p RGB565 mode," line.long 0x04 "L7ORIGINADDRESS,Sets the logical frame origin address of L7 layer" line.long 0x08 "L7DISPLAYADDRESS,Sets the display origin address of L7 layer" line.long 0x0C "L7DISPLAYPOSITION,L7DisplayPosition" line.long 0x10 "L7WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the L7 layer window" hexmask.long.word 0x10 16.--27. 1. " L7WY ,Sets the display position coordinates (WY) of the L7 layer window" hexmask.long.word 0x10 0.--11. 1. " L7WX ,Sets the display position coordinates (WX) of the L7 layer window" line.long 0x14 "L7WINDOWSIZE,L7WindowSize" hexmask.long.word 0x14 16.--27. 1. " L7WH ,Sets the size of the L7 layer window. Specifies the height" hexmask.long.word 0x14 0.--11. 1. " L7WW ,Sets the size of the L7 layer window.Specifies the width in units of pixels" group.long 0x1A4++0x13 line.long 0x00 "L7READSKIPMODE,Controls read skip operation of layer L7" bitfld.long 0x00 15. " L7SE ,Specifies whether or not to enable the read skip function" "Disabled,Enabled" hexmask.long.word 0x00 0.--8. 1. " L7PRE ,Specifies whether or not to perform a read operation for the partition corresponding to each bit" line.long 0x04 "L7PARTITIONX,Specifies two X coordinates which split the L7 layer when performing a read skip" hexmask.long.word 0x04 16.--27. 1. " L7PX1 ,Specifies the second X coordinate for read skip partition" hexmask.long.word 0x04 0.--11. 1. " L7PX0 ,Specifies the first X coordinate for read skip partition" line.long 0x08 "L7PARTITIONY,Specifies two Y coordinates which split the L7 layer when performing a read skip" hexmask.long.word 0x08 16.--27. 1. " L7PY1 ,Specifies the second Y coordinate for read skip partition" hexmask.long.word 0x08 0.--11. 1. " L7PY0 ,Specifies the first Y coordinate for read skip partition" line.long 0x0C "L7BLEND,Configures blending operation of Layer 7" bitfld.long 0x0C 16.--18. " L7BLMODE ,Selects Blend Mode" "Standard alpha blending,Standard alpha blending + RGB,Constant alpha blending,Simultaneous alpha blending,Simultaneous alpha blending + RGB,,," bitfld.long 0x0C 14. " L7BE ,Enables blend" "Disabled,Enabled" textline " " bitfld.long 0x0C 13. " L7BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" bitfld.long 0x0C 11.--12. " L7AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" textline " " bitfld.long 0x0C 10. " L7AS ,Selects an alpha layer" "Alpha,LA0 to LA3" bitfld.long 0x0C 9. " L7AM ,A-field of pixel controls blend operation mask bit" "Not control,Control" textline " " hexmask.long.word 0x0C 0.--8. 1. " L7BR ,Sets the blend ratio" line.long 0x10 "L7TRANSPARENCYCONTROL,Controls transparency processing of Layer 7" bitfld.long 0x10 31. " L7ZT ,Enables transparent processing for Layer L7" "Disabled,Enabled" hexmask.long.tbyte 0x10 0.--23. 1. " L7TC ,Sets the color value (code) treated as transparent color for L7 layer" group.long 0x1B8++0x0F line.long 0x00 "LA0LAYERMODE,LA0LayerMode" bitfld.long 0x00 31. " LA0E ,Enables the LA0 layer" "Disabled,Enabled" hexmask.long.byte 0x00 0.--7. 1. " LA0W ,Sets the memory width (stride) of the LA0 layer logical frame in units of 64 bytes" line.long 0x04 "LA0DISPLAYADDRESS,LA0DisplayAddress" line.long 0x08 "LA0WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the LA0 layer window" hexmask.long.word 0x08 16.--27. 1. " LA0WY ,Specifies the WY coordinate" hexmask.long.word 0x08 0.--11. 1. " LA0WX ,Specifies the WX coordinate" line.long 0x0C "LA0WINDOWSIZE,Sets the size of the LA0 layer window" hexmask.long.word 0x0C 16.--27. 1. " LA0WH ,Specifies the height" hexmask.long.word 0x0C 0.--11. 1. " LA0WW ,Specifies the width in units of pixels" group.long 0x1C8++0x0F line.long 0x00 "LA1LAYERMODE,LA1LayerMode" bitfld.long 0x00 31. " LA1E ,Enables the LA1 layer" "Disabled,Enabled" hexmask.long.byte 0x00 0.--7. 1. " LA1W ,Sets the memory width (stride) of the LA1 layer logical frame in units of 64 bytes" line.long 0x04 "LA1DISPLAYADDRESS,LA1DisplayAddress" line.long 0x08 "LA1WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the LA1 layer window" hexmask.long.word 0x08 16.--27. 1. " LA1WY ,Specifies the WY coordinate" hexmask.long.word 0x08 0.--11. 1. " LA1WX ,Specifies the WX coordinate" line.long 0x0C "LA1WINDOWSIZE,Sets the size of the LA1 layer window" hexmask.long.word 0x0C 16.--27. 1. " LA1WH ,Specifies the height" hexmask.long.word 0x0C 0.--11. 1. " LA1WW ,Specifies the width in units of pixels" group.long 0x1D8++0x0F line.long 0x00 "LA2LAYERMODE,LA2LayerMode" bitfld.long 0x00 31. " LA2E ,Enables the LA2 layer" "Disabled,Enabled" hexmask.long.byte 0x00 0.--7. 1. " LA2W ,Sets the memory width (stride) of the LA2 layer logical frame in units of 64 bytes" line.long 0x04 "LA2DISPLAYADDRESS,LA2DisplayAddress" line.long 0x08 "LA2WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the LA2 layer window" hexmask.long.word 0x08 16.--27. 1. " LA2WY ,Specifies the WY coordinate" hexmask.long.word 0x08 0.--11. 1. " LA2WX ,Specifies the WX coordinate" line.long 0x0C "LA2WINDOWSIZE,Sets the size of the LA2 layer window" hexmask.long.word 0x0C 16.--27. 1. " LA2WH ,Specifies the height" hexmask.long.word 0x0C 0.--11. 1. " LA2WW ,Specifies the width in units of pixels" group.long 0x1E8++0x0F line.long 0x00 "LA3LAYERMODE,LA3LayerMode" bitfld.long 0x00 31. " LA3E ,Enables the LA3 layer" "Disabled,Enabled" hexmask.long.byte 0x00 0.--7. 1. " LA3W ,Sets the memory width (stride) of the LA3 layer logical frame in units of 64 bytes" line.long 0x04 "LA3DISPLAYADDRESS,LA3DisplayAddress" line.long 0x08 "LA3WINDOWPOSITION,Sets the display position coordinates (WX,WY) of the LA3 layer window" hexmask.long.word 0x08 16.--27. 1. " LA3WY ,Specifies the WY coordinate" hexmask.long.word 0x08 0.--11. 1. " LA3WX ,Specifies the WX coordinate" line.long 0x0C "LA3WINDOWSIZE,Sets the size of the LA3 layer window" hexmask.long.word 0x0C 16.--27. 1. " LA3WH ,Specifies the height" hexmask.long.word 0x0C 0.--11. 1. " LA3WW ,Specifies the width in units of pixels" group.long 0x1F8++0x0F line.long 0x00 "CURSOR0PRIORITYMODE,Sets the priority of cursor display" bitfld.long 0x00 31. " CEN0 ,Enables/disables display of cursor 0" "Disabled,Enabled" bitfld.long 0x00 30. " SC1ENC0 ,Determines whether cursor0 is included in screen1 or not" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0ENC0 ,Determines whether cursor0 is included in screen0 or not" "Not included,Included" bitfld.long 0x00 1.--2. " CU0SIZ ,Sets Size of cursor 0" "128x128,64x64,32x32,16x16" textline " " bitfld.long 0x00 0. " CUO0 ,Sets the display priority of cursor 0 and the L0 layer" "Below,Above" line.long 0x04 "CURSOR0ORIGINADDRESS,Cursor0OriginAddress" line.long 0x08 "CURSOR0POSITION,Sets the display position coordinates (CUX0,CUY0) of cursor 0 in units of pixels" hexmask.long.word 0x08 16.--27. 1. " CUY0 ,Specifies the CUY coordinate" hexmask.long.word 0x08 0.--11. 1. " CUX0 ,Specifies the CUX coordinate" line.long 0x0C "CURSOR0TRANSPARENTCONTROL,Cursor0TransparentControl" bitfld.long 0x0C 8. " CUZT0 ,Controls the transparency mode" "Disabled,Enabled" hexmask.long.byte 0x0C 0.--7. 1. " CUTC0 ,Specifies Cursor 0 color data that should be treated as transparent" group.long 0x208++0x0F line.long 0x00 "CURSOR1PRIORITYMODE,Sets the priority of cursor display" bitfld.long 0x00 31. " CEN1 ,Enables/disables display of cursor 1" "Disabled,Enabled" bitfld.long 0x00 30. " SC1ENC1 ,Determines whether cursor1 is included in screen1 or not" "Not included,Included" textline " " bitfld.long 0x00 29. " SC0ENC1 ,Determines whether cursor1 is included in screen0 or not" "Not included,Included" bitfld.long 0x00 1.--2. " CU1SIZ ,Sets Size of cursor 1" "128x128,64x64,32x32,16x16" textline " " bitfld.long 0x00 0. " CUO1 ,Sets the display priority of cursor 1 and the L1 layer" "Below,Above" line.long 0x04 "CURSOR1ORIGINADDRESS,Cursor1OriginAddress" line.long 0x08 "CURSOR1POSITION,Sets the display position coordinates (CUX1,CUY1) of cursor 1 in units of pixels" hexmask.long.word 0x08 16.--27. 1. " CUY1 ,Specifies the CUY coordinate" hexmask.long.word 0x08 0.--11. 1. " CUX1 ,Specifies the CUX coordinate" line.long 0x0C "CURSOR1TRANSPARENTCONTROL,Cursor1TransparentControl" bitfld.long 0x0C 8. " CUZT1 ,Controls the transparency mode" "Disabled,Enabled" hexmask.long.byte 0x0C 0.--7. 1. " CUTC1 ,Specifies Cursor 1 color data that should be treated as transparent" group.long 0x218++0x17 line.long 0x00 "L1COEFFICIENT0,Set color matrix of Layer 1" hexmask.long.word 0x00 16.--26. 1. " L1A12 ,11-bit signed fixed-point value" hexmask.long.word 0x00 0.--10. 1. " L1A11 ,11-bit signed fixed-point value" line.long 0x04 "L1COEFFICIENT1,Set color matrix of Layer 1" hexmask.long.word 0x04 16.--24. 1. " L1B1 ,9-bit signed integer" hexmask.long.word 0x04 0.--10. 1. " L1A13 ,11-bit signed fixed-point value" line.long 0x08 "L1COEFFICIENT2,Set color matrix of Layer 1" hexmask.long.word 0x08 16.--26. 1. " L1A22 ,11-bit signed fixed-point value" hexmask.long.word 0x08 0.--10. 1. " L1A21 ,11-bit signed fixed-point value" line.long 0x0C "L1COEFFICIENT3,Set color matrix of Layer 1" hexmask.long.word 0x0C 16.--24. 1. " L1B2 ,9-bit signed integer" hexmask.long.word 0x0C 0.--10. 1. " L1A23 ,11-bit signed fixed-point value" line.long 0x10 "L1COEFFICIENT4,Set color matrix of Layer 1" hexmask.long.word 0x10 16.--26. 1. " L1A32 ,11-bit signed fixed-point value" hexmask.long.word 0x10 0.--10. 1. " L1A31 ,11-bit signed fixed-point value" line.long 0x14 "L1COEFFICIENT5,Set color matrix of Layer 1" hexmask.long.word 0x14 16.--24. 1. " L1B3 ,9-bit signed integer" hexmask.long.word 0x14 0.--10. 1. " L1A33 ,11-bit signed fixed-point value" group.long 0x230++0x17 line.long 0x00 "L2COEFFICIENT0,Set color matrix of Layer 1" hexmask.long.word 0x00 16.--26. 1. " L2A12 ,11-bit signed fixed-point value" hexmask.long.word 0x00 0.--10. 1. " L2A11 ,11-bit signed fixed-point value" line.long 0x04 "L2COEFFICIENT1,Set color matrix of Layer 1" hexmask.long.word 0x04 16.--24. 1. " L2B1 ,9-bit signed integer" hexmask.long.word 0x04 0.--10. 1. " L2A13 ,11-bit signed fixed-point value" line.long 0x08 "L2COEFFICIENT2,Set color matrix of Layer 1" hexmask.long.word 0x08 16.--26. 1. " L2A22 ,11-bit signed fixed-point value" hexmask.long.word 0x08 0.--10. 1. " L2A21 ,11-bit signed fixed-point value" line.long 0x0C "L2COEFFICIENT3,Set color matrix of Layer 1" hexmask.long.word 0x0C 16.--24. 1. " L2B2 ,9-bit signed integer" hexmask.long.word 0x0C 0.--10. 1. " L2A23 ,11-bit signed fixed-point value" line.long 0x10 "L2COEFFICIENT4,Set color matrix of Layer 1" hexmask.long.word 0x10 16.--26. 1. " L2A32 ,11-bit signed fixed-point value" hexmask.long.word 0x10 0.--10. 1. " L2A31 ,11-bit signed fixed-point value" line.long 0x14 "L2COEFFICIENT5,Set color matrix of Layer 1" hexmask.long.word 0x14 16.--24. 1. " L2B3 ,9-bit signed integer" hexmask.long.word 0x14 0.--10. 1. " L2A33 ,11-bit signed fixed-point value" group.long 0x248++0x17 line.long 0x00 "L3COEFFICIENT0,Set color matrix of Layer 1" hexmask.long.word 0x00 16.--26. 1. " L3A12 ,11-bit signed fixed-point value" hexmask.long.word 0x00 0.--10. 1. " L3A11 ,11-bit signed fixed-point value" line.long 0x04 "L3COEFFICIENT1,Set color matrix of Layer 1" hexmask.long.word 0x04 16.--24. 1. " L3B1 ,9-bit signed integer" hexmask.long.word 0x04 0.--10. 1. " L3A13 ,11-bit signed fixed-point value" line.long 0x08 "L3COEFFICIENT2,Set color matrix of Layer 1" hexmask.long.word 0x08 16.--26. 1. " L3A22 ,11-bit signed fixed-point value" hexmask.long.word 0x08 0.--10. 1. " L3A21 ,11-bit signed fixed-point value" line.long 0x0C "L3COEFFICIENT3,Set color matrix of Layer 1" hexmask.long.word 0x0C 16.--24. 1. " L3B2 ,9-bit signed integer" hexmask.long.word 0x0C 0.--10. 1. " L3A23 ,11-bit signed fixed-point value" line.long 0x10 "L3COEFFICIENT4,Set color matrix of Layer 1" hexmask.long.word 0x10 16.--26. 1. " L3A32 ,11-bit signed fixed-point value" hexmask.long.word 0x10 0.--10. 1. " L3A31 ,11-bit signed fixed-point value" line.long 0x14 "L3COEFFICIENT5,Set color matrix of Layer 1" hexmask.long.word 0x14 16.--24. 1. " L3B3 ,9-bit signed integer" hexmask.long.word 0x14 0.--10. 1. " L3A33 ,11-bit signed fixed-point value" group.long 0x260++0x17 line.long 0x00 "L4COEFFICIENT0,Set color matrix of Layer 1" hexmask.long.word 0x00 16.--26. 1. " L4A12 ,11-bit signed fixed-point value" hexmask.long.word 0x00 0.--10. 1. " L4A11 ,11-bit signed fixed-point value" line.long 0x04 "L4COEFFICIENT1,Set color matrix of Layer 1" hexmask.long.word 0x04 16.--24. 1. " L4B1 ,9-bit signed integer" hexmask.long.word 0x04 0.--10. 1. " L4A13 ,11-bit signed fixed-point value" line.long 0x08 "L4COEFFICIENT2,Set color matrix of Layer 1" hexmask.long.word 0x08 16.--26. 1. " L4A22 ,11-bit signed fixed-point value" hexmask.long.word 0x08 0.--10. 1. " L4A21 ,11-bit signed fixed-point value" line.long 0x0C "L4COEFFICIENT3,Set color matrix of Layer 1" hexmask.long.word 0x0C 16.--24. 1. " L4B2 ,9-bit signed integer" hexmask.long.word 0x0C 0.--10. 1. " L4A23 ,11-bit signed fixed-point value" line.long 0x10 "L4COEFFICIENT4,Set color matrix of Layer 1" hexmask.long.word 0x10 16.--26. 1. " L4A32 ,11-bit signed fixed-point value" hexmask.long.word 0x10 0.--10. 1. " L4A31 ,11-bit signed fixed-point value" line.long 0x14 "L4COEFFICIENT5,Set color matrix of Layer 1" hexmask.long.word 0x14 16.--24. 1. " L4B3 ,9-bit signed integer" hexmask.long.word 0x14 0.--10. 1. " L4A33 ,11-bit signed fixed-point value" textline " " rgroup.long 0x300++0x07 line.long 0x00 "BUFFERROR,Buffer error register" bitfld.long 0x00 11. " LA[3]ERR ,Error status of LA3 FIFO" "Normal,Error" bitfld.long 0x00 10. " [2] ,Error status of LA2 FIFO" "Normal,Error" bitfld.long 0x00 9. " [1] ,Error status of LA1 FIFO" "Normal,Error" bitfld.long 0x00 8. " [0] ,Error status of LA0 FIFO" "Normal,Error" textline " " bitfld.long 0x00 7. " L[7]ERR ,Error status of L7 FIFO" "Normal,Error" bitfld.long 0x00 6. " [6] ,Error status of L6 FIFO" "Normal,Error" bitfld.long 0x00 5. " [5] ,Error status of L5 FIFO" "Normal,Error" bitfld.long 0x00 4. " [4] ,Error status of L4 FIFO" "Normal,Error" textline " " bitfld.long 0x00 3. " [3] ,Error status of L3 FIFO" "Normal,Error" bitfld.long 0x00 2. " [2] ,Error status of L2 FIFO" "Normal,Error" bitfld.long 0x00 1. " [1] ,Error status of L1 FIFO" "Normal,Error" bitfld.long 0x00 0. " [0] ,Error status of L0 FIFO" "Normal,Error" textline " " line.long 0x04 "BUFFERRIE,Enable to generate interrupt signal of buffer error. Emerald-P and -L(MP) only" bitfld.long 0x04 0. " BUFFERRIE ,BuffErrIE" "Disabled,Enabled" group.long 0x400++0x3 line.long 0x00 "PALETTE0,Memory mapped RAM for Palette0" button "PALETTE0" "d (ad:0xD0810000+0x400)--(ad:0xD0810000+0x7FF) /long" group.long 0x800++0x3 line.long 0x00 "PALETTE1,Memory mapped RAM for Palette1" button "PALETTE1" "d (ad:0xD0810000+0x800)--(ad:0xD0810000+0xBFF) /long" group.long 0xC00++0x3 line.long 0x00 "PALETTE2,Memory mapped RAM for Palette2" button "PALETTE2" "d (ad:0xD0810000+0xC00)--(ad:0xD0810000+0xFFF) /long" group.long 0x1000++0x3 line.long 0x00 "PALETTE3,Memory mapped RAM for Palette3" button "PALETTE3" "d (ad:0xD0810000+0x1000)--(ad:0xD0810000+0x13FF) /long" group.long 0x1400++0x3 line.long 0x00 "CLUTDATA,Memory mapped RAM for CLUT" button "CLUTDATA" "d (ad:0xD0810000+0x1400)--(ad:0xD0810000+0x17FF) /long" group.long 0x1800++0x03 line.long 0x00 "SOFTWARERESETENABLE,SW reset" bitfld.long 0x00 0. " SOFTRESET ,Executes a software reset" "No reset,Reset" width 0xb tree.end sif (cpu()=="MB86R12") tree "Display 2" base ad:0x38A00000 width 29. group.long 0x00++0x23 line.long 0x00 "DISPLAYENABLE,DisplayEnable register" bitfld.long 0x00 0. " DEN ,Display Enable" "Disabled,Enabled" if (((per.l(ad:0x38A00000+0x04))&0x01)==0x01) group.long 0x04++0x03 line.long 0x00 "REGISTERUPDATEMODE,Defines the register update mode" bitfld.long 0x00 29. " RUMLAY_[0] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 28. " [1] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 27. " [2] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 26. " [3] ,Defines update mode" "Direct,Synchronous" textline " " bitfld.long 0x00 25. " [4] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 24. " [5] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 23. " [6] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 22. " [7] ,Defines update mode" "Direct,Synchronous" textline " " bitfld.long 0x00 21. " [8] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 20. " [9 ] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 19. " [10] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 18. " [11] ,Defines update mode" "Direct,Synchronous" textline " " bitfld.long 0x00 17. " [12] ,Defines update mode" "Direct,Synchronous" bitfld.long 0x00 16. " [13] ,Defines update mode" "Direct,Synchronous" textline " " bitfld.long 0x00 1. " RUM ,Selects a mode during which register values are updated in sync with vertical synchronization globally" "Off,On" bitfld.long 0x00 0. " RUMSEL ,Selects the global register update mode" "Global,Per layer" else group.long 0x04++0x03 line.long 0x00 "REGISTERUPDATEMODE,Defines the register update mode" textline " " textline " " textline " " textline " " bitfld.long 0x00 1. " RUM ,Selects a mode during which register values are updated in sync with vertical synchronization globally" "Off,On" bitfld.long 0x00 0. " RUMSEL ,Selects the global register update mode" "Global,Per layer" endif group.long 0x08++0x1B line.long 0x00 "REGISTERUPDATESELECTION,Set the layers for synchronous update by vertical synchronization with RUFlag" bitfld.long 0x00 0. " RUFSEL ,Selects global update for all layers or independent update per layer" "All layers,Layers selected" textline " " line.long 0x04 "REGISTERUPDATEFLAG,Triggers the register update at next vertical synchronization" bitfld.long 0x04 29. " RUFLAY_[13] ,Defines the layer is updated with the next vertical synchronization" "No update,Update" bitfld.long 0x04 28. " [12] ,Defines the layer is updated with the next vertical synchronization" "No update,Update" bitfld.long 0x04 27. " [11] ,Defines the layer is updated with the next vertical synchronization" "No update,Update" bitfld.long 0x04 26. " [10] ,Defines the layer is updated with the next vertical synchronization" "No update,Update" textline " " bitfld.long 0x04 25. " [9] ,Defines the layer is updated with the next vertical synchronization" "No update,Update" bitfld.long 0x04 24. " [8] ,Defines the layer is updated with the next vertical synchronization" "No update,Update" bitfld.long 0x04 23. " [7] ,Defines the layer is updated with the next vertical synchronization" "No update,Update" bitfld.long 0x04 22. " [6] ,Defines the layer is updated with the next vertical synchronization" "No update,Update" textline " " bitfld.long 0x04 21. " [5] ,Defines the layer is updated with the next vertical synchronization" "No update,Update" bitfld.long 0x04 20. " [4] ,Defines the layer is updated with the next vertical synchronization" "No update,Update" bitfld.long 0x04 19. " [3] ,Defines the layer is updated with the next vertical synchronization" "No update,Update" bitfld.long 0x04 18. " [2] ,Defines the layer is updated with the next vertical synchronization" "No update,Update" textline " " bitfld.long 0x04 17. " [1] ,Defines the layer is updated with the next vertical synchronization" "No update,Update" bitfld.long 0x04 16. " [0] ,Defines the layer is updated with the next vertical synchronization" "No update,Update" textline " " bitfld.long 0x04 0. " RUFLAG ,RUFlag" "Initial state/Update completed,Vertical synchronization" textline " " line.long 0x08 "DCLKCONFIG,Defines the pixel output clock" bitfld.long 0x08 18.--22. " DCKDEL ,Defines an additional delay in units of the reference clock" "No additional delay,,+2 reference clock,,+3 reference clock,,+4 reference clock,,+5 reference clock,,+6 reference clock,,+7 reference clock,,+8 reference clock,,+9 reference clock,,+10 reference clock,,+11 reference clock,,+12 reference clock,,+13 reference clock,,+14 reference clock,,+15 reference clock,,+16 reference clock," bitfld.long 0x08 17. " DCKDELEN ,Display clock delay" "Disabled,Enabled" bitfld.long 0x08 16. " DCKINV ,Inversion of display clock" "Not inverted,Inverted" textline " " bitfld.long 0x08 9.--14. " SC ,Divides the display reference clock by the set ratio for dot clocks generation" "Not divide,Div/2,Div/3,Div/4,Div/5,Div/6,Div/7,Div/8,Div/9,Div/10,Div/11,Div/12,Div/13,Div/14,Div/15,Div/16,Div/17,Div/18,Div/19,Div/20,Div/21,Div/22,Div/23,Div/24,Div/25,Div/26,Div/27,Div/28,Div/29,Div/30,Div/31,Div/32,Div/33,Div/34,Div/35,Div/36,Div/37,Div/38,Div/39,Div/40,Div/41,Div/42,Div/43,Div/44,Div/45,Div/46,Div/47,Div/48,Div/49,Div/50,Div/51,Div/52,Div/53,Div/54,Div/55,Div/56,Div/57,Div/58,Div/59,Div/60,Div/61,Div/62,Div/63,Div/64" bitfld.long 0x08 8. " DCSEL ,Selects the frequency of the reference input clock" "800 MHz/1066 MHz,Standard frequency" bitfld.long 0x08 1. " ENDCOP ,Sets the display clock output pin to high impedance" "Don't switch,Switch" textline " " bitfld.long 0x08 0. " CKS ,Selects the reference clock" "PLL,DCLKI" line.long 0x0C "DISPLAYPORTCONFIG,Configuration of ports for synchronization signals" bitfld.long 0x0C 3. " SYOUTEN ,Switch display YSNC and VSYNC pin direction" "Input Ports,Output Ports" bitfld.long 0x0C 2. " ENDDOP ,Sets the display data outputs to high impedance" "Normal,High" textline " " bitfld.long 0x0C 1. " SF ,Sets synchronization active value" "Low active,High active" bitfld.long 0x0C 0. " ESY ,Enables external synchronization mode" "Disabled,Enabled" line.long 0x10 "DISPLAYRESOLUTION,Configuration of display resolution" hexmask.long.word 0x10 16.--27. 1. " VTR ,Specifies the vertical total line count" hexmask.long.word 0x10 0.--11. 1. " HTP ,Specifies the horizontal total pixel count" line.long 0x14 "ACTIVEAREA,Configuration of active video area" hexmask.long.word 0x14 16.--27. 1. " VDP ,Specifies the vertical display period in units of lines" hexmask.long.word 0x14 0.--11. 1. " HDP ,Specifies the horizontal display boundary in units of pixel" line.long 0x18 "HORSYNCHTIMINGCONFIGURATION,Configuration of the horizontal synchronization output timing" hexmask.long.byte 0x18 16.--23. 1. " HSW ,Specifies the pulse width of the horizontal synchronization signal in units of pixel" hexmask.long.word 0x18 0.--11. 1. " HSP ,Specifies the position of the horizontal synchronization signal in units of pixel" group.long 0x24++0x23 line.long 0x00 "VERSYNCHTIMINGCONFIGURATION,Configuration of the vertical synchronization output timing" bitfld.long 0x00 31. " VSWH ,Extends the pulse width of the vertical synchronization signal by half of a line" "0,1" hexmask.long.byte 0x00 16.--21. 1. " VSW ,Specifies the pulse width of the vertical synchronization signal in units of pixel clocks" hexmask.long.word 0x00 0.--11. 1. " VSP ,Specifies the position of the vertical synchronization signal in units of lines" line.long 0x04 "DISPLAYOUTPUTCONFIG,Configuration of output modes" bitfld.long 0x04 4. " DCKEDGE ,Defines the DCLK OUTPUT edge mode" "Single edge mode,Dual edge mode" bitfld.long 0x04 3. " EEQ ,Sets the equalization pulse mode for the CSYNC signal" "No equalization,Equalization" bitfld.long 0x04 0.--1. " SYNC ,Sets display output mode" "Non-interlaced mode,Interlace mode,,Interlace video mode" line.long 0x08 "MULTIDISPLAYDUALVIEWSETUP,Configuration of dual view processing" bitfld.long 0x08 31. " MDEN ,Enable/Disable multi-display functionality" "Disabled,Enabled" bitfld.long 0x08 2. " DVPATTERN ,Control the re-ordering between different lines" "Disabled,Enabled" textline " " bitfld.long 0x08 1. " DVDTSW ,Left and Right screen swapping" "Don't swap,Swap" bitfld.long 0x08 0. " DVEN ,DualView Enable" "Disabled,Enabled" line.long 0x0C "CHROMAKEYCONTROL,Configuration of chroma keying" bitfld.long 0x0C 31. " KCS ,Selects whether the display output color" "Display,L0 layer" bitfld.long 0x0C 30. " KYEN ,Enables/Disables chroma-key processing" "Disabled,Enabled" hexmask.long.tbyte 0x0C 0.--23. 1. " KYC ,Sets the key color used to perform chromakey processing" line.long 0x10 "CLUTCONTROL,Enables/Disables the Color Lookup table" bitfld.long 0x10 31. " CLUTEN ,Enable Color Look Up" "Disabled,Enabled" line.long 0x14 "DITHERCONTROL,Configures the Dither unit" bitfld.long 0x14 4. " DITHMS ,Select mode for dithering" "Temporal dithering,Spatial dithering" bitfld.long 0x14 3. " DITHRS ,Sets dither range" "Low,High" textline " " bitfld.long 0x14 1.--2. " DITHFS ,Select output format for dithering" "10x10x10->8x8x8,10x10x10->7x7x7,10x10x10->6x6x6,10x10x10->5x6x5" bitfld.long 0x14 0. " DITHEN ,Enable Dithering" "Disabled,Enabled" line.long 0x18 "DISPLAYBACKGROUNDCOLOR,This color is displayed on screen areas that are not included in any display window" bitfld.long 0x18 31. " DBGEN ,Enable the background color" "Disabled,Enabled" hexmask.long.byte 0x18 16.--23. 1. " DBGR ,Specifies the red level of the background color" textline " " hexmask.long.byte 0x18 8.--15. 1. " DBGG ,Specifies the green level of the background color" hexmask.long.byte 0x18 0.--7. 1. " DBGB ,Specifies the blue level of the background color" line.long 0x20 "DISPLAYLAYERSELECT,Defines the layer superimposition order" textline " " bitfld.long 0x20 28.--31. " DLS_[7] ,Selects the bottom layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 24.--27. " [6] ,Selects the seventh layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 20.--23. " [5] ,Selects the sixth layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 16.--19. " [4] ,Selects the fifth layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" textline " " bitfld.long 0x20 12.--15. " [3] ,Selects the fourth layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 8.--11. " [2] ,Selects the third layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 4.--7. " [1] ,Selects the second layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" bitfld.long 0x20 0.--3. " [0] ,Selects the top layer" "L0 layer,L1 layer,L2 layer,L3 layer,L4 layer,L5 layer,L6 layer,L7 layer,,,,,,,,No layer is selected" textline " " group.long 0x44++0x23 line.long 0x00 "COMPATIBILITYMODE,Handles RUBY compatibility" bitfld.long 0x00 4. " RUBYMD ,Ruby Mode" "Ruby mode off,Ruby mode on" bitfld.long 0x00 0. " AH ,Address high keep this bit zero" "0,1" group.long 0x78++0x0B line.long 0x00 "L1LAYERMODE,1LayerMode" bitfld.long 0x00 31. " L1E ,Enables L1 layer display" "Disabled,Enabled" bitfld.long 0x00 30. " SC1EN1 ,SC1en1" "Not included,Included" bitfld.long 0x00 29. " SC0EN1 ,SC0en1" "Not included,Included" textline " " bitfld.long 0x00 20. " L1ENBWAUTO ,Set an automatic video capture operation mode when L1CS is in capture mode" "No automatic mode,Automatic Buffer managment" bitfld.long 0x00 19. " L1YC ,Sets the L1 layer color format" "RGB mode,YC mode" bitfld.long 0x00 18. " L1CS ,Sets whether to use the L1 layer as a normal display layer or as a video capture layer" "Normal mode,Video Capture mode" textline " " bitfld.long 0x00 17. " L1INTL ,Sets a video capture operation mode when L1CS is in capture mode" "Normal mode,Weave mode" bitfld.long 0x00 16. " L1VMAG ,Enables/disables capture image upscaling" "Disabled,Enabled" hexmask.long.byte 0x00 0.--7. 1. " L1W ,Sets the memory width (stride) of the L1 layer logical frame in units of 64 bytes" line.long 0x04 "L1COLORMODE,L1ColorMode" bitfld.long 0x04 8.--10. " L1CMODE ,Sets the L1 layer color mode" "16 b/p ARGB mode,24 b/p ARGB mode,16 b/p RGBA mode,24 b/p RGBA mode,24 b/p ABGR mode,Indirect color 8 b/p,," bitfld.long 0x04 0.--3. " L1PB ,Indicates the value to be added to the index when drawing the L1 layer palette" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "L1DISPLAYADDRESS,Sets the display window origin address of the L1 layer" rgroup.long 0x84++0x07 line.long 0x00 "CAPTURE1BUFFERDISPADDRESS0,Starting address of the displayed capture image" line.long 0x04 "CAPTURE1BUFFERDISPADDRESS1,This register indicates the starting address of an even field of the capture screen" group.long 0x8C++0x07 line.long 0x00 "L1WINDOWPOSITION,L1WindowPosition" hexmask.long.word 0x00 16.--27. 1. " L1WY ,Sets the display position coordinates (WY) of the L1 layer window" hexmask.long.word 0x00 0.--11. 1. " L1WX ,Sets the display position coordinates (WX) of the L1 layer window" line.long 0x04 "L1WINDOWSIZE,L1WindowSize" hexmask.long.word 0x04 16.--27. 1. " L1WH ,Sets the size of the L1 layer window. Specifies the height" hexmask.long.word 0x04 0.--11. 1. " L1WW ,Sets the size of the L1 layer window.Specifies the width in units of pixels" group.long 0x9C++0x07 line.long 0x00 "L1BLEND,Configures blending operation of Layer 1" bitfld.long 0x00 16.--18. " L1BLMODE ,Selects Blend Mode" "Standard alpha,Standard alpha + RGB,Constant alpha,Simultaneous alpha,Simultaneous alpha + RGB,,," bitfld.long 0x00 14. " L1BE ,Enables blend" "Disabled,Enabled" bitfld.long 0x00 13. " L1BI ,Selects whether or not 1/256 is added when the blend ratio is not 0" "Do not add 1/256,Add 1/256" textline " " bitfld.long 0x00 11.--12. " L1AL ,Selects an alpha dedicated layer" "LA0,LA1,LA2,LA3" bitfld.long 0x00 10. " L1AS ,Selects an alpha layer" "Alpha field,LA0 to LA3" bitfld.long 0x00 9. " L1AM ,L1AM (L1 A-field mask)" "Not control,Control" textline " " hexmask.long.word 0x00 0.--8. 1. " L1BR ,Sets the blend ratio" line.long 0x04 "L1TRANSPARENCYCONTROL,Controls transparency processing of Layer 1" bitfld.long 0x04 31. " L1ZT ,Enables transparent processing for Layer L1" "Disabled,Enabled" hexmask.long.tbyte 0x04 0.--23. 1. " L1TC ,Sets the color value (code) treated as transparent color for L1 layer" group.long 0x218++0x17 line.long 0x00 "L1COEFFICIENT0,Set color matrix of Layer 1" hexmask.long.word 0x00 16.--26. 1. " L1A12 ,11-bit signed fixed-point value" hexmask.long.word 0x00 0.--10. 1. " L1A11 ,11-bit signed fixed-point value" line.long 0x04 "L1COEFFICIENT1,Set color matrix of Layer 1" hexmask.long.word 0x04 16.--24. 1. " L1B1 ,9-bit signed integer" hexmask.long.word 0x04 0.--10. 1. " L1A13 ,11-bit signed fixed-point value" line.long 0x08 "L1COEFFICIENT2,Set color matrix of Layer 1" hexmask.long.word 0x08 16.--26. 1. " L1A22 ,11-bit signed fixed-point value" hexmask.long.word 0x08 0.--10. 1. " L1A21 ,11-bit signed fixed-point value" line.long 0x0C "L1COEFFICIENT3,Set color matrix of Layer 1" hexmask.long.word 0x0C 16.--24. 1. " L1B2 ,9-bit signed integer" hexmask.long.word 0x0C 0.--10. 1. " L1A23 ,11-bit signed fixed-point value" line.long 0x10 "L1COEFFICIENT4,Set color matrix of Layer 1" hexmask.long.word 0x10 16.--26. 1. " L1A32 ,11-bit signed fixed-point value" hexmask.long.word 0x10 0.--10. 1. " L1A31 ,11-bit signed fixed-point value" line.long 0x14 "L1COEFFICIENT5,Set color matrix of Layer 1" hexmask.long.word 0x14 16.--24. 1. " L1B3 ,9-bit signed integer" hexmask.long.word 0x14 0.--10. 1. " L1A33 ,11-bit signed fixed-point value" rgroup.long 0x300++0x07 line.long 0x00 "BUFFERROR,Buffer error register" bitfld.long 0x00 1. " L1ERR ,Error status of L1 FIFO" "Normal,Error" line.long 0x04 "BUFFERRIE,Enable to generate interrupt signal of buffer error. Emerald-P and -L(MP) only" bitfld.long 0x04 0. " BUFFERRIE ,BuffErrIE" "Disabled,Enabled" group.long 0x1400++0x3 line.long 0x00 "CLUTDATA,Memory mapped RAM for CLUT" button "CLUTDATA" "d (ad:0x38A00000+0x1400)--(ad:0x38A00000+0x17FF) /long" group.long 0x1800++0x03 line.long 0x00 "SOFTWARERESETENABLE,SW reset" bitfld.long 0x00 0. " SOFTRESET ,Executes a software reset" "No reset,Reset" width 0xb tree.end endif tree "Writeback Processor" base ad:0xD0820000 width 18. group.long 0x00++0x07 line.long 0x00 "SOFTWARERESET,Software Reset Register" bitfld.long 0x00 0. " SOFTRESET ,Software reset" "No reset,Reset" line.long 0x04 "FLOWCONTROL,Writeback Flow Control Register" bitfld.long 0x04 1. " WBMODE ,Writeback operation mode" "Single shot mode,Continuous mode" bitfld.long 0x04 0. " WBE ,Writeback enable" "Disabled,Enabled" rgroup.long 0x08++0x03 line.long 0x00 "STATUS,Writeback Status Register" bitfld.long 0x00 0.--2. " STATUS ,Status" "Default state,Odd field mode,Even field mode,,Both fields mode(first),Both fields mode(second),?..." group.long 0x0C++0x13 line.long 0x00 "MODE,Writeback Mode Register" hexmask.long.byte 0x00 16.--23. 1. " WBW ,Memory width" bitfld.long 0x00 10. " RGBWIDTH ,Data size of a single pixel" "16 bits/pixel,32 bits/pixel" bitfld.long 0x00 8.--9. " RGBAMODE ,Pixel data format" "ARGB,RGBA,ABGR,?..." textline " " bitfld.long 0x00 4.--6. " FMODE ,Field mode" ",Odd field mode,Even field mode,Both fields mode,,,,Both fields mode" sif (cpu()=="MB86R24") bitfld.long 0x00 0.--3. " VSEL ,Data source for the writeback unit" "DC0/DDS0,DC1/DDS0,DC0/DDS1,DC1/DDS1,Capture unit 0,Capture unit 1,Capture unit 2,Capture unit 3,,,MIPI unit,,Capture unit 4,Capture unit 5,?..." else bitfld.long 0x00 0.--2. " VSEL ,Data source for the writeback unit" "DC0/DDS0,DC1/DDS0,DC0/DDS1,DC1/DDS1,Capture unit 0,Capture unit 1,Capture unit 2,Capture unit 3" endif line.long 0x04 "ORIGINADDRESS0,Writeback Origin Address 0 Register" hexmask.long 0x04 3.--28. 0x08 " WBOA0 ,Starting address of write destination image area 0" line.long 0x08 "ORIGINADDRESS1,Writeback Origin Address 1 Register" hexmask.long 0x08 3.--28. 0x08 " WBOA1 ,Starting address of write destination image area 1" line.long 0x0C "START,Writeback Start Register" hexmask.long.word 0x0C 16.--27. 1. " WIVSTR ,Writeback image vertical start" hexmask.long.word 0x0C 0.--11. 1. " WIHSTR ,Writeback image horizontal start" line.long 0x10 "END,Writeback End Register" hexmask.long.word 0x10 16.--27. 1. " WIVEND ,Writeback image vertical end" hexmask.long.word 0x10 0.--11. 1. " WIHEND ,Writeback image horizontal end" sif (cpu()=="MB86R12") group.long 0x24++0x03 line.long 0x00 "VSTREND,Set Different Address For Even Field" hexmask.long.word 0x00 16.--27. 1. " WIVEND ,Writeback image vertical end" hexmask.long.word 0x00 0.--11. 1. " WIHEND ,Writeback image horizontal end" else group.long 0x24++0x03 line.long 0x00 "WRITEBACKVSTREND,Set Different Address For Even Field" bitfld.long 0x00 31. " ENADDADR ,Enable the WritebackVstrEnd register setting as additional WIVSTARTEND" "Disabled,Enabled" hexmask.long.word 0x00 16.--27. 1. " WBVERES ,Writeback image vertical end" hexmask.long.word 0x00 0.--11. 1. " WBVSRES ,Writeback image horizontal end" endif width 0x0B tree.end tree "CAP0" base ad:0xD0830000 width 15. group.long 0x00++0x3B line.long 0x00 "VCM,Video Capture Mode register" bitfld.long 0x00 31. " VIE ,Video Input Capture Enable" "Disabled,Enabled" bitfld.long 0x00 29.--30. " VIS ,Video Input Format Select" "ITU BT 656 input select,HD 720p input select,RGB input select," textline " " bitfld.long 0x00 28. " VICE ,Video Input Clock Enable" "Disabled,Enabled" sif (cpu()=="MB86R11F") bitfld.long 0x00 26.--27. " A_MSB ,MSB Address bits 29-28 of the capture unit address" "0 to 256MByte,256MByte to 512MByte,512MByte to 768MByte,768MByte to 1GByte" endif textline " " bitfld.long 0x00 24.--25. " CM ,Capture Mode register" "Capture mode,,,Capture" textline " " bitfld.long 0x00 20. " VI ,Vertical Interpolation" "On,Off" bitfld.long 0x00 14.--19. " VDSS_VDMS ,Video Data Mode Select" "RGB_888,,RGB_888_A0,,RGB_666_0,,RGB_888_A1,,RGB_666_1,,RGB_666_A0,,ITU_656_0_P,ITU_656_0_N,RGB_666_A1,,ITU_656_1_P,ITU_656_1_N,,,ITU_656_2_P,ITU_656_2_N,ITU_656_1_A1,,ITU_656_3_P,ITU_656_3_P_N,HD_SDR16_0A0,,HD_DDR8_0,HD_SDR8_0,HD_SDR16_0A1,,HD_DDR8_1,HD_SDR8_1,,,HD_DDR8_2,HD_SDR8_2,,,HD_DDR8_3,HD_SDR8_3,,,HD_SDR16_0,..." textline " " bitfld.long 0x00 11. " VF ,Input Video Format Select" "ITU-R BT 656,YC multiplex" bitfld.long 0x00 4. " DSEL ,Select the display unit for video output" "Display 0,Display 1" textline " " bitfld.long 0x00 2. " NRGB ,Native RGB input on, native RGB input is set" "RGB to YUV 422 mode,RGB mode" bitfld.long 0x00 1. " VS ,Video Select" "NTSC,PAL" line.long 0x04 "CSC,Capture Scale register" bitfld.long 0x04 27.--31. " VSCI ,Vertical Scale Integer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.word 0x04 16.--26. 1. " VSCF ,Vertical Scale Fraction" textline " " bitfld.long 0x04 11.--15. " HSCI ,Horizontal Scale Integer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.word 0x04 0.--10. 1. " HSCF ,Horizontal Scale Fraction" line.long 0x08 "VCS,Video Capture Status 0 register" textline " " bitfld.long 0x08 6. " CE_[6] ,ITU-R 656 short term H code error (EAV)" "No error,Error" bitfld.long 0x08 5. " [5] ,ITU-R 656 short term H code error (SAV)" "No error,Error" bitfld.long 0x08 4. " [4] ,ITU-R 656 long term H code error (EAV)" "No error,Error" bitfld.long 0x08 3. " [3] ,ITU-R 656 long term H code error (SAV)" "No error,Error" textline " " bitfld.long 0x08 2. " [2] ,ITU-R 656 undefined error (Code Bit7-0) " "No error,Error" bitfld.long 0x08 1. " [1] ,ITU-R 656 undefined error (Code Bit7-4)" "No error,Error" bitfld.long 0x08 0. " [0] ,ITU-R 656 undefined error (Code Bit7)" "No error,Error" textline " " line.long 0x0C "VCS_MSK,Video Capture Status 0 Mask register" bitfld.long 0x0C 6. " MSK_ERR6 ,Code Error 6 Mask" "Masked,Not masked" bitfld.long 0x0C 5. " MSK_ERR5 ,Code Error 5 Mask" "Masked,Not masked" textline " " bitfld.long 0x0C 4. " MSK_ERR4 ,Code Error 4 Mask" "Masked,Not masked" bitfld.long 0x0C 3. " MSK_ERR3 ,Code Error 3 Mask" "Masked,Not masked" textline " " bitfld.long 0x0C 2. " MSK_ERR2 ,Code Error 2 Mask" "Masked,Not masked" bitfld.long 0x0C 1. " MSK_ERR1 ,Code Error 1 Mask" "Masked,Not masked" textline " " bitfld.long 0x0C 0. " MSK_ERR0 ,Code Error 0 Mask" "Masked,Not masked" line.long 0x10 "CBM0,Video Capture Buffer Mode 0 register" bitfld.long 0x10 31. " OO ,Odd Only Mode" "Normal Mode,Capture odd fields only" bitfld.long 0x10 30. " SBUF ,Single Buffer" "Normal Mode,Single Buffer Mode" textline " " bitfld.long 0x10 29. " CRGB ,Conversion to RGB" "Disabled,Enabled" hexmask.long.byte 0x10 16.--23. 1. " CBW ,Capture Buffer Memory Width" textline " " bitfld.long 0x10 15. " BLEN ,Blending Enable" "Disabled,Enabled" bitfld.long 0x10 14. " C24 ,Color 24bit/pixel" "16 bits/pixel,24 bits/pixel" textline " " bitfld.long 0x10 12.--13. " RGBA ,Configure RGBA component order" "ARGB,RGBA,ABGR,RGB565" bitfld.long 0x10 0. " CBST ,Capture Burst Mode" "Normal,Long" line.long 0x14 "CBA0,Video Capture Buffer 0 Address register" hexmask.long 0x14 3.--31. 0x08 " CBOA ,Video Capture Buffer Origin Address" line.long 0x18 "CBA1,Video Capture Buffer 1 Address register" hexmask.long 0x18 3.--31. 0x08 " CBLA ,Video Capture Buffer Limit Address" line.long 0x1C "CISTR,Capture Image Start register" hexmask.long.word 0x1C 16.--27. 1. " CIVSTR0 ,Capture Image Vertical Start" hexmask.long.word 0x1C 0.--11. 1. " CIHSTR ,Capture Image Horizontal start" line.long 0x20 "CIEND,Capture Image End register" hexmask.long.word 0x20 16.--27. 1. " CIVEND0 ,Capture Image Vertical End 0" hexmask.long.word 0x20 0.--11. 1. " CIHEND ,Capture Image Horizontal End 0" line.long 0x24 "CISEO,Capture Image Start End Optional register" hexmask.long.word 0x24 16.--27. 1. " CIVEND1 ,Capture Image Vertical End 1" hexmask.long.word 0x24 0.--11. 1. " CIVSTR1 ,Capture Image Vertical Start 1" line.long 0x28 "CHP,Capture Horizontal Pixel register" hexmask.long.word 0x28 0.--9. 1. " CHP ,Capture Horizontal Pixel" line.long 0x2C "CVP,Capture Vertical Pixel register" hexmask.long.word 0x2C 16.--25. 1. " CVPP ,Capture Vertical Pixel for PAL" hexmask.long.word 0x2C 0.--9. 1. " CVPN ,Capture Vertical Pixel for NTSC" line.long 0x30 "CLPF,Capture Low-Pass Filters register" bitfld.long 0x30 24.--27. " CVLPF ,Capture Vertical LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x30 16.--19. " CHLPF ,Capture Horizontal LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x34 "CMSS,Capture Magnify Source Size register" hexmask.long.word 0x34 16.--25. 1. " CMSHP ,Capture Magnify Source Horizontal Pixel" hexmask.long.word 0x34 0.--9. 1. " CMSVL ,Capture Magnify Source Vertical Line" line.long 0x38 "CMDS,Capture Magnify Destination Size register" hexmask.long.word 0x38 16.--26. 1. " CMDHP ,Capture Magnify Destination Horizontal Pixel" hexmask.long.word 0x38 0.--9. 1. " CMDVL ,Capture Magnify Destination Vertical Line" group.long 0x48++0x23 line.long 0x00 "RGBHC,RGB input HSYNC cycle register" hexmask.long.word 0x00 0.--13. 1. " RGBHC ,Sets the horizontal cycle (HSYNC) time when RGB mode is used" line.long 0x04 "RGBHEN,RGB input horizontal enable area register" hexmask.long.word 0x04 16.--27. 1. " RGBHST ,Configures the start position of effective pixel data" hexmask.long.word 0x04 0.--12. 1. " RGBHEN ,Sets the effective pixel data size per pixel" line.long 0x08 "RGBVEN,RGB input vertical enable area register" bitfld.long 0x08 28.--29. " RGBVST_T_O ,RGB input Vertical Enable area start position for odd fields" "0,1,2,3" hexmask.long.word 0x08 16.--24. 1. " RGBVST ,RGB input Vertical Enable area Size" textline " " hexmask.long.word 0x08 0.--12. 1. " RGBVEN ,RGB input Vertical Enable area size" line.long 0x0C "VIN_VSAMP,Video Input VSYNC Sampling mode register" bitfld.long 0x0C 8.--9. " VJITFLT ,Jitter Filter configuration" "Samples on HSYNC,,," bitfld.long 0x0C 0. " FLDREV ,Field Reverse, inverts the logic of the CAP0FID input" "Disabled,Enabled" line.long 0x10 "RGBS,RGB input sync register" bitfld.long 0x10 16. " RM ,RGB input mode select" ",RGB direct input mode" bitfld.long 0x10 1. " HP ,HSYNC Polarity" "Falling edge,Rising edge" textline " " bitfld.long 0x10 0. " VP ,VINSYNC Polarity" "Falling edge,Rising edge" line.long 0x14 "RGBCMY,RGB Color Conversion Matrix Y coefficient register" hexmask.long.word 0x14 22.--31. 1. " A11 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x14 11.--20. 1. " A12 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x14 0.--9. 1. " A13 ,10 bit signed value, the lower 8 bits are the fractional part" line.long 0x18 "RGBCMCB,RGB Color Convert Matrix Cb coefficient register" hexmask.long.word 0x18 22.--31. 1. " A21 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x18 11.--20. 1. " A22 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x18 0.--9. 1. " A23 ,10 bit signed value, the lower 8 bits are the fractional part" line.long 0x1C "RGBCMCR,RGB Color Convert Matrix Cr coefficient register" hexmask.long.word 0x1C 22.--31. 1. " A31 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x1C 11.--20. 1. " A32 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x1C 0.--9. 1. " A33 ,10 bit signed value, the lower 8 bits are the fractional part" line.long 0x20 "RGBCMB,RGB Color Convert Matrix b coefficient register" hexmask.long.word 0x20 22.--30. 1. " B1 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x20 11.--19. 1. " B2 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x20 0.--8. 1. " B3 ,10 bit signed value, the lower 8 bits are the fractional part" group.long 0x78++0x0F line.long 0x00 "CINT,Capture interrupt register" bitfld.long 0x00 1. " IVS ,VS (VSYNC) Interrupt" "No interrupt,Interrupt" line.long 0x04 "CINTMSK,Capture Interrupt Mask register" bitfld.long 0x04 4. " DIRECT_INT ,Feeds VSYNC to the interrupt line" "Standard interrupt,Direct Interrupt" bitfld.long 0x04 2.--3. " MSK_FIELD ,Mask the VS interrupt for top or bottom field" "Not masked,Top field,Bottom field," textline " " bitfld.long 0x04 1. " MSK_VSI ,Mask VS (VSYNC) Interrupt" "Disabled,Active" line.long 0x08 "SYNC_ERR,Synchronisation error register" bitfld.long 0x08 25. " VS_LONG_ERR ,Vsync Long Error" "No error,Error" bitfld.long 0x08 24. " VS_SHORT_ERR ,Vsync Short Error" "No error,Error" textline " " bitfld.long 0x08 16. " VS_ERR ,Vsync Error(disconnected)" "No error,Error" bitfld.long 0x08 9. " HS_LONG_ERR ,Hsync Long Error" "No error,Error" textline " " bitfld.long 0x08 8. " HS_SHORT_ERR ,Hsync Short Error" "No error,Error" bitfld.long 0x08 0. " HS_ERR ,Hsync Error(disconnected)" "No error,Error" line.long 0x0C "SYNC_ERR_MSK,Synchronisation Error Mask register" bitfld.long 0x0C 25. " MSK_VS_LONG_ERR ,Mask Vsync Long Error" "Enabled,Disabled" bitfld.long 0x0C 24. " MSK_VS_SHORT_ERR ,Mask Vsync Short Error" "Enabled,Disabled" textline " " bitfld.long 0x0C 16. " MSK_VS_ERR ,Mask Vsync Error" "Enabled,Disabled" bitfld.long 0x0C 9. " MSK_HS_LONG_ERR ,Mask Hsync Long Error" "Enabled,Disabled" textline " " bitfld.long 0x0C 8. " MSK_HS_SHORT_ERR ,Mask Hsync Short Error" "Enabled,Disabled" bitfld.long 0x0C 0. " MSK_HS_ERR ,Mask Hsync Error" "Enabled,Disabled" rgroup.long 0x88++0x03 line.long 0x00 "CVCNT,Capture Vertical Count register" hexmask.long.word 0x00 0.--11. 1. " CVCNT ,Capture Vertical Count" group.long 0x98++0x07 line.long 0x00 "CDCN,Capture Data Count (NTSC) register" hexmask.long.word 0x00 16.--28. 1. " BDCN ,Blanking Data Count (NTSC)" hexmask.long.word 0x00 0.--13. 1. " VDCN ,Valid Data Count (NTSC)" line.long 0x04 "CDCP,Capture Data Count (PAL) register" hexmask.long.word 0x04 16.--28. 1. " BDCP ,Blanking Data Count (PAL)" hexmask.long.word 0x04 0.--13. 1. " VDCP ,Valid Data Count (PAL)" group.long 0xA8++0x0B line.long 0x00 "MDS,Mode select register" bitfld.long 0x00 4.--5. " VCMIM ,YC Multiplex video input mode" "RGB input mode,,,YC Multiplex input mode" line.long 0x04 "CDCNS,Capture Data Count (NTSC Short)" hexmask.long.word 0x04 16.--28. 1. " BDCN_S ,Blanking Data Count (NTSC Short)" hexmask.long.word 0x04 0.--13. 1. " VDCN_S ,Valid Data Count (NTSC Short)" line.long 0x08 "CDCPS,Capture Data Count (PAL Short)" hexmask.long.word 0x08 16.--28. 1. " BDCP_S ,Blanking Data Count (PAL Short)" hexmask.long.word 0x08 0.--13. 1. " VDCP_S ,Valid Data Count (PAL Short)" rgroup.long 0xCC++0x03 line.long 0x00 "VINLC_KEP,Video Input Line Count" hexmask.long.word 0x00 0.--12. 1. " VIN_LINE_NO_KEP ,Line count of one frame (field) including the blanking period" group.long 0xD4++0x0F line.long 0x00 "VHSLS,Video Input HSYNC Long/Short register" hexmask.long.word 0x00 16.--29. 1. " VIN_HS_LONG ,Sets the video input long interval HSYNC monitoring" hexmask.long.word 0x00 0.--13. 1. " VIN_HS_SHORT ,Configures the video input short interval HSYNC monitoring" line.long 0x04 "VHSDC,Video HSYNC Down Count register" bitfld.long 0x04 31. " VIN_EHSYNC_MSK ,Video Input Error HSYNC Mask" "Disabled,Enabled" hexmask.long.byte 0x04 0.--7. 1. " VIN_HDOWN_CNT ,Configures the video input HSYNC disconnected monitoring cycle" line.long 0x08 "VVSLS,Video Input VSYNC Long/Short register" hexmask.long.word 0x08 16.--28. 1. " VIN_VS_LONG ,Sets video input long interval VSYNC monitoring" hexmask.long.word 0x08 0.--12. 1. " VIN_VS_SHORT ,Configures the video input short interval VSYNC monitoring" if (((per.l(ad:0xD0830000+0xA8))&0x30)==0x30) group.long 0xE0++0x03 line.long 0x00 "VVSDC,Video Input VSYNC Down Count register" bitfld.long 0x00 31. " VIN_EVSYNC_MSK ,Video Input Error VSYNC Mask" "0,1" hexmask.long.byte 0x00 0.--7. 1. " VIN_VDOWN_CNT ,Configures the video input VSYNC disconnected monitoring cycle" else group.long 0xE0++0x03 line.long 0x00 "VVSDC,Video Input VSYNC Down Count register" hexmask.long.byte 0x00 0.--7. 1. " VIN_VDOWN_CNT ,Configures the video input VSYNC disconnected monitoring cycle" endif group.long 0x108++0x27 line.long 0x00 "SDER,Still Detection Enable Register" hexmask.long.word 0x00 16.--26. 1. " SDMOPIX ,The number of pixels of the reduced frame n which were detected as motion pixels" rbitfld.long 0x00 3. " BF ,Bottom Field" "Top,Bottom" textline " " rbitfld.long 0x00 2. " SDMON ,Still Detection Monitor" "Interpolation,Non-interpolation" bitfld.long 0x00 1. " SDMAN ,Still Detection Manual Mode" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " SDEN ,Still Detection Enable" "Disabled,Enabled" line.long 0x04 "SDCF0,Still Detection Config register 0" hexmask.long.word 0x04 16.--24. 1. " MLC ,Maximum Line Count" hexmask.long.word 0x04 0.--10. 1. " MPC ,Maximum Pixel Count" line.long 0x08 "SDCF1,Still Detection Config register 1" hexmask.long.word 0x08 16.--26. 1. " MB ,Motion Blocks" hexmask.long.word 0x08 0.--10. 1. " MA ,The Maximum Address (MA) of reduced frame memory" line.long 0x0C "SDTH,Still Detection Threshold register" hexmask.long.tbyte 0x0C 0.--16. 1. " CBTH ,Compare Blocks Threshold value" line.long 0x10 "SDHY,Still Detection Hysteresis register" bitfld.long 0x10 24.--29. " SLB ,Still Look Back" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x10 16.--21. " MLB ,Motion Look Back" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x10 8.--13. " MO2ST ,Motion to Still switch value" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x10 0.--5. " ST2MO ,Still to Motion switch value" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x14 "HDCFG,High Definition (HD) Configuration Register" bitfld.long 0x14 5. " HD_EN_TO_DET ,Enable timeout detection" "Disabled,Enabled" bitfld.long 0x14 4. " HD_EN_ERR_DET ,Enable error detection" "Disabled,Enabled" textline " " bitfld.long 0x14 2.--3. " HD_SPREAD ,HD spread" "All AV tags are on the Y,All AV tags are on the CbCr,Alternating CbCr component,Alternating Y component" bitfld.long 0x14 1. " HD_SWAP ,HD swap" "No swap,Swap" textline " " bitfld.long 0x14 0. " HD_RUN ,HD run" "Disabled,Enabled" line.long 0x18 "HDEST,High definition Error Status Register" bitfld.long 0x18 5. " HD_L_ERR_NOL ,Long Error in Number of active lines detected" "No error,Error" bitfld.long 0x18 4. " HD_L_ERR_HACT ,Long Error in HACTIVE detected" "No error,Error" textline " " bitfld.long 0x18 3. " HD_L_ERR_HBL ,Long Error in HBLANK detected" "No error,Error" bitfld.long 0x18 2. " HD_S_ERR_NOL ,Short Error in Number of active lines detected" "No error,Error" textline " " bitfld.long 0x18 1. " HD_S_ERR_HACT ,Short Error in HACTIVE detected" "No error,Error" bitfld.long 0x18 0. " HD_S_ERR_HBL ,Short Error in HBLANK detected" "No error,Error" line.long 0x1C "HDMSK,High definition Error Mask register" bitfld.long 0x1C 5. " MSK_HD_L_ERR_NOL ,Mask register for HD_L_ERR_NOL" "Disabled,Enabled" bitfld.long 0x1C 4. " MSK_HD_L_ERR_HACT ,Mask register for HD_L_ERR_HACT" "Disabled,Enabled" textline " " bitfld.long 0x1C 3. " MSK_HD_L_ERR_HBL ,Mask register for HD_L_ERR_HBL" "Disabled,Enabled" bitfld.long 0x1C 2. " MSK_HD_S_ERR_NOL ,Mask register for HD_S_ERR_NOL" "Disabled,Enabled" textline " " bitfld.long 0x1C 1. " MSK_HD_S_ERR_HACT ,Mask register for HD_S_ERR_HACT" "Disabled,Enabled" bitfld.long 0x1C 0. " MSK_HD_S_ERR_HBL ,Mask register for HD_S_ERR_HBL" "Disabled,Enabled" line.long 0x20 "HDHBL,High definition HBLANK error detection parameter register" hexmask.long.word 0x20 16.--26. 1. " HD_L_HBL ,HBLANK long parameter to compare with. Error if frame HBLANK is larger than this value" hexmask.long.word 0x20 0.--10. 1. " HD_S_HBL ,HBLANK short parameter to compare with.Error if frame HBLANK is smaller than this value" line.long 0x24 "HDHACT,High definition HACTIVE error detection parameter register" hexmask.long.word 0x24 16.--24. 1. " HD_L_HACT ,HACTIVE long parameter to compare with Error if frame HACTIVE is larger than this value" hexmask.long.word 0x24 0.--10. 1. " HD_S_HACT ,HACTIVE short parameter to compare with Error if frame HACTIVE is smaller than this value" group.long 0x130++0x27 line.long 0x00 "HDNOL,High definition NOL (number of lines) error detection parameter register" hexmask.long.word 0x00 16.--26. 1. " HD_L_NOL ,Number of active lines long parameter" hexmask.long.word 0x00 0.--10. 1. " HD_S_NOL ,Number of active lines short parameter" line.long 0x04 "CM_COEFF_0,Color Matrix Coefficient Register 0" hexmask.long.word 0x04 0.--10. 1. " CMKY ,Coefficient for Y, same for R,G,B calculation" line.long 0x08 "CM_COEFF_1,Color Matrix Coefficient Register 1" hexmask.long.word 0x08 16.--26. 1. " CMKCBB ,Coefficient for Cb, for calculation of B value" hexmask.long.word 0x08 0.--10. 1. " CMKCBG ,Coefficient for Cb, for calculation of G value" line.long 0x0C "CM_COEFF_2,Color Matrix Coefficient Register 2" hexmask.long.word 0x0C 16.--26. 1. " CMKCRG ,Coefficient for Cr, for calculation of G value" hexmask.long.word 0x0C 0.--10. 1. " CMKCRR ,Coefficient for Cr, for calculation of R value" line.long 0x10 "SWRSTREG,Software Reset Register" bitfld.long 0x10 0. " SWRST ,Software Reset" "No reset,Reset" line.long 0x14 "WRBUFFERERROR,Write Buffer Error" eventfld.long 0x14 0. " WRBE ,Error Status" "Normal,Error" line.long 0x18 "WRBUFERRIE,Write Buffer Error Interrupt Enable" bitfld.long 0x18 0. " WRBEIE ,Enable to generate interrupt singal of buffer error. Emerald-L(MP) only" "Disabled,Enbaled" line.long 0x1C "D_YHLPF,Direct coefficient for Y component Horizontal LPF" bitfld.long 0x1C 24.--29. " K4YH ,K4 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x1C 18.--23. " K3YH ,K3 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x1C 12.--17. " K2YH ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x1C 6.--11. " K1YH ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x1C 0.--5. " K0YH ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x20 "D_CHLPF,Direct coefficient for C component Horizontal LPF" bitfld.long 0x20 24.--29. " K4CH ,K4 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x20 18.--23. " K3CH ,K3 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x20 12.--17. " K2CH ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x20 6.--11. " K1CH ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x20 0.--5. " K0CH ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x24 "D_VLPF,Direct coefficient for vertical LPF" bitfld.long 0x24 26.--30. " K2CV ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x24 21.--25. " K1CV ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x24 16.--20. " K0CV ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x24 10.--14. " K2YV ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x24 5.--9. " K1YV ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x24 0.--4. " K0YV ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x380++0x03 line.long 0x00 "CBM1,Capture Buffer Mode 1" sif (cpu()=="MB86R12") bitfld.long 0x00 20. " YRGB ,Enable YRGB format, only valid if 32bpp is used" "Disabled,Enabled" textline " " endif bitfld.long 0x00 16. " WMODE ,Weave mode" "Disabled,Enabled" bitfld.long 0x00 2. " IDMAXH ,ID max hold" "From 255 to 0,Stops at 255" textline " " bitfld.long 0x00 1. " IDRESM ,ID reset mode" "No reset,Reset" bitfld.long 0x00 0. " IDRDS ,ID read select" "Read now,Read recently" rgroup.long 0x384++0x03 line.long 0x00 "CBSTA,Capture Buffer Status" bitfld.long 0x00 16. " VALID ,Valid" "No effective,Effective" hexmask.long.byte 0x00 0.--7. 1. " IDCNT ,ID count" group.long 0x388++0x03 line.long 0x00 "CBA2,Capture Buffer Address 2" hexmask.long 0x00 4.--31. 0x10 " CBA2 ,The first address in a new area when the swap of the capture buffer is executed is set" rgroup.long 0x38C++0x03 line.long 0x00 "CBA3,Capture Buffer Address 3" group.long 0x390++0x07 line.long 0x00 "CBSWS,Capture Buffer Swap Select" bitfld.long 0x00 3. " CBSWS3 ,Capture buffer swap select 3" "Not selected,Selected" bitfld.long 0x00 2. " CBSWS2 ,Capture buffer swap select 2" "Not selected,Selected" textline " " bitfld.long 0x00 2. " CBSWS1 ,Capture buffer swap select 1" "Not selected,Selected" bitfld.long 0x00 0. " CBSWS0 ,Capture buffer swap select 0" "Not selected,Selected" line.long 0x04 "CBSWP,Capture Buffer Swap" width 0xb tree.end tree "CAP1" base ad:0xD0840000 width 15. group.long 0x00++0x3B line.long 0x00 "VCM,Video Capture Mode register" bitfld.long 0x00 31. " VIE ,Video Input Capture Enable" "Disabled,Enabled" bitfld.long 0x00 29.--30. " VIS ,Video Input Format Select" "ITU BT 656 input select,HD 720p input select,RGB input select," textline " " bitfld.long 0x00 28. " VICE ,Video Input Clock Enable" "Disabled,Enabled" sif (cpu()=="MB86R11F") bitfld.long 0x00 26.--27. " A_MSB ,MSB Address bits 29-28 of the capture unit address" "0 to 256MByte,256MByte to 512MByte,512MByte to 768MByte,768MByte to 1GByte" endif textline " " bitfld.long 0x00 24.--25. " CM ,Capture Mode register" "Capture mode,,,Capture" textline " " bitfld.long 0x00 20. " VI ,Vertical Interpolation" "On,Off" bitfld.long 0x00 14.--19. " VDSS_VDMS ,Video Data Mode Select" "RGB_888,,RGB_888_A0,,RGB_666_0,,RGB_888_A1,,RGB_666_1,,RGB_666_A0,,ITU_656_0_P,ITU_656_0_N,RGB_666_A1,,ITU_656_1_P,ITU_656_1_N,,,ITU_656_2_P,ITU_656_2_N,ITU_656_1_A1,,ITU_656_3_P,ITU_656_3_P_N,HD_SDR16_0A0,,HD_DDR8_0,HD_SDR8_0,HD_SDR16_0A1,,HD_DDR8_1,HD_SDR8_1,,,HD_DDR8_2,HD_SDR8_2,,,HD_DDR8_3,HD_SDR8_3,,,HD_SDR16_0,..." textline " " bitfld.long 0x00 11. " VF ,Input Video Format Select" "ITU-R BT 656,YC multiplex" bitfld.long 0x00 4. " DSEL ,Select the display unit for video output" "Display 0,Display 1" textline " " bitfld.long 0x00 2. " NRGB ,Native RGB input on, native RGB input is set" "RGB to YUV 422 mode,RGB mode" bitfld.long 0x00 1. " VS ,Video Select" "NTSC,PAL" line.long 0x04 "CSC,Capture Scale register" bitfld.long 0x04 27.--31. " VSCI ,Vertical Scale Integer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.word 0x04 16.--26. 1. " VSCF ,Vertical Scale Fraction" textline " " bitfld.long 0x04 11.--15. " HSCI ,Horizontal Scale Integer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.word 0x04 0.--10. 1. " HSCF ,Horizontal Scale Fraction" line.long 0x08 "VCS,Video Capture Status 0 register" textline " " bitfld.long 0x08 6. " CE_[6] ,ITU-R 656 short term H code error (EAV)" "No error,Error" bitfld.long 0x08 5. " [5] ,ITU-R 656 short term H code error (SAV)" "No error,Error" bitfld.long 0x08 4. " [4] ,ITU-R 656 long term H code error (EAV)" "No error,Error" bitfld.long 0x08 3. " [3] ,ITU-R 656 long term H code error (SAV)" "No error,Error" textline " " bitfld.long 0x08 2. " [2] ,ITU-R 656 undefined error (Code Bit7-0) " "No error,Error" bitfld.long 0x08 1. " [1] ,ITU-R 656 undefined error (Code Bit7-4)" "No error,Error" bitfld.long 0x08 0. " [0] ,ITU-R 656 undefined error (Code Bit7)" "No error,Error" textline " " line.long 0x0C "VCS_MSK,Video Capture Status 0 Mask register" bitfld.long 0x0C 6. " MSK_ERR6 ,Code Error 6 Mask" "Masked,Not masked" bitfld.long 0x0C 5. " MSK_ERR5 ,Code Error 5 Mask" "Masked,Not masked" textline " " bitfld.long 0x0C 4. " MSK_ERR4 ,Code Error 4 Mask" "Masked,Not masked" bitfld.long 0x0C 3. " MSK_ERR3 ,Code Error 3 Mask" "Masked,Not masked" textline " " bitfld.long 0x0C 2. " MSK_ERR2 ,Code Error 2 Mask" "Masked,Not masked" bitfld.long 0x0C 1. " MSK_ERR1 ,Code Error 1 Mask" "Masked,Not masked" textline " " bitfld.long 0x0C 0. " MSK_ERR0 ,Code Error 0 Mask" "Masked,Not masked" line.long 0x10 "CBM0,Video Capture Buffer Mode 0 register" bitfld.long 0x10 31. " OO ,Odd Only Mode" "Normal Mode,Capture odd fields only" bitfld.long 0x10 30. " SBUF ,Single Buffer" "Normal Mode,Single Buffer Mode" textline " " bitfld.long 0x10 29. " CRGB ,Conversion to RGB" "Disabled,Enabled" hexmask.long.byte 0x10 16.--23. 1. " CBW ,Capture Buffer Memory Width" textline " " bitfld.long 0x10 15. " BLEN ,Blending Enable" "Disabled,Enabled" bitfld.long 0x10 14. " C24 ,Color 24bit/pixel" "16 bits/pixel,24 bits/pixel" textline " " bitfld.long 0x10 12.--13. " RGBA ,Configure RGBA component order" "ARGB,RGBA,ABGR,RGB565" bitfld.long 0x10 0. " CBST ,Capture Burst Mode" "Normal,Long" line.long 0x14 "CBA0,Video Capture Buffer 0 Address register" hexmask.long 0x14 3.--31. 0x08 " CBOA ,Video Capture Buffer Origin Address" line.long 0x18 "CBA1,Video Capture Buffer 1 Address register" hexmask.long 0x18 3.--31. 0x08 " CBLA ,Video Capture Buffer Limit Address" line.long 0x1C "CISTR,Capture Image Start register" hexmask.long.word 0x1C 16.--27. 1. " CIVSTR0 ,Capture Image Vertical Start" hexmask.long.word 0x1C 0.--11. 1. " CIHSTR ,Capture Image Horizontal start" line.long 0x20 "CIEND,Capture Image End register" hexmask.long.word 0x20 16.--27. 1. " CIVEND0 ,Capture Image Vertical End 0" hexmask.long.word 0x20 0.--11. 1. " CIHEND ,Capture Image Horizontal End 0" line.long 0x24 "CISEO,Capture Image Start End Optional register" hexmask.long.word 0x24 16.--27. 1. " CIVEND1 ,Capture Image Vertical End 1" hexmask.long.word 0x24 0.--11. 1. " CIVSTR1 ,Capture Image Vertical Start 1" line.long 0x28 "CHP,Capture Horizontal Pixel register" hexmask.long.word 0x28 0.--9. 1. " CHP ,Capture Horizontal Pixel" line.long 0x2C "CVP,Capture Vertical Pixel register" hexmask.long.word 0x2C 16.--25. 1. " CVPP ,Capture Vertical Pixel for PAL" hexmask.long.word 0x2C 0.--9. 1. " CVPN ,Capture Vertical Pixel for NTSC" line.long 0x30 "CLPF,Capture Low-Pass Filters register" bitfld.long 0x30 24.--27. " CVLPF ,Capture Vertical LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x30 16.--19. " CHLPF ,Capture Horizontal LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x34 "CMSS,Capture Magnify Source Size register" hexmask.long.word 0x34 16.--25. 1. " CMSHP ,Capture Magnify Source Horizontal Pixel" hexmask.long.word 0x34 0.--9. 1. " CMSVL ,Capture Magnify Source Vertical Line" line.long 0x38 "CMDS,Capture Magnify Destination Size register" hexmask.long.word 0x38 16.--26. 1. " CMDHP ,Capture Magnify Destination Horizontal Pixel" hexmask.long.word 0x38 0.--9. 1. " CMDVL ,Capture Magnify Destination Vertical Line" group.long 0x48++0x23 line.long 0x00 "RGBHC,RGB input HSYNC cycle register" hexmask.long.word 0x00 0.--13. 1. " RGBHC ,Sets the horizontal cycle (HSYNC) time when RGB mode is used" line.long 0x04 "RGBHEN,RGB input horizontal enable area register" hexmask.long.word 0x04 16.--27. 1. " RGBHST ,Configures the start position of effective pixel data" hexmask.long.word 0x04 0.--12. 1. " RGBHEN ,Sets the effective pixel data size per pixel" line.long 0x08 "RGBVEN,RGB input vertical enable area register" bitfld.long 0x08 28.--29. " RGBVST_T_O ,RGB input Vertical Enable area start position for odd fields" "0,1,2,3" hexmask.long.word 0x08 16.--24. 1. " RGBVST ,RGB input Vertical Enable area Size" textline " " hexmask.long.word 0x08 0.--12. 1. " RGBVEN ,RGB input Vertical Enable area size" line.long 0x0C "VIN_VSAMP,Video Input VSYNC Sampling mode register" bitfld.long 0x0C 8.--9. " VJITFLT ,Jitter Filter configuration" "Samples on HSYNC,,," bitfld.long 0x0C 0. " FLDREV ,Field Reverse, inverts the logic of the CAP0FID input" "Disabled,Enabled" line.long 0x10 "RGBS,RGB input sync register" bitfld.long 0x10 16. " RM ,RGB input mode select" ",RGB direct input mode" bitfld.long 0x10 1. " HP ,HSYNC Polarity" "Falling edge,Rising edge" textline " " bitfld.long 0x10 0. " VP ,VINSYNC Polarity" "Falling edge,Rising edge" line.long 0x14 "RGBCMY,RGB Color Conversion Matrix Y coefficient register" hexmask.long.word 0x14 22.--31. 1. " A11 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x14 11.--20. 1. " A12 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x14 0.--9. 1. " A13 ,10 bit signed value, the lower 8 bits are the fractional part" line.long 0x18 "RGBCMCB,RGB Color Convert Matrix Cb coefficient register" hexmask.long.word 0x18 22.--31. 1. " A21 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x18 11.--20. 1. " A22 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x18 0.--9. 1. " A23 ,10 bit signed value, the lower 8 bits are the fractional part" line.long 0x1C "RGBCMCR,RGB Color Convert Matrix Cr coefficient register" hexmask.long.word 0x1C 22.--31. 1. " A31 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x1C 11.--20. 1. " A32 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x1C 0.--9. 1. " A33 ,10 bit signed value, the lower 8 bits are the fractional part" line.long 0x20 "RGBCMB,RGB Color Convert Matrix b coefficient register" hexmask.long.word 0x20 22.--30. 1. " B1 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x20 11.--19. 1. " B2 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x20 0.--8. 1. " B3 ,10 bit signed value, the lower 8 bits are the fractional part" group.long 0x78++0x0F line.long 0x00 "CINT,Capture interrupt register" bitfld.long 0x00 1. " IVS ,VS (VSYNC) Interrupt" "No interrupt,Interrupt" line.long 0x04 "CINTMSK,Capture Interrupt Mask register" bitfld.long 0x04 4. " DIRECT_INT ,Feeds VSYNC to the interrupt line" "Standard interrupt,Direct Interrupt" bitfld.long 0x04 2.--3. " MSK_FIELD ,Mask the VS interrupt for top or bottom field" "Not masked,Top field,Bottom field," textline " " bitfld.long 0x04 1. " MSK_VSI ,Mask VS (VSYNC) Interrupt" "Disabled,Active" line.long 0x08 "SYNC_ERR,Synchronisation error register" bitfld.long 0x08 25. " VS_LONG_ERR ,Vsync Long Error" "No error,Error" bitfld.long 0x08 24. " VS_SHORT_ERR ,Vsync Short Error" "No error,Error" textline " " bitfld.long 0x08 16. " VS_ERR ,Vsync Error(disconnected)" "No error,Error" bitfld.long 0x08 9. " HS_LONG_ERR ,Hsync Long Error" "No error,Error" textline " " bitfld.long 0x08 8. " HS_SHORT_ERR ,Hsync Short Error" "No error,Error" bitfld.long 0x08 0. " HS_ERR ,Hsync Error(disconnected)" "No error,Error" line.long 0x0C "SYNC_ERR_MSK,Synchronisation Error Mask register" bitfld.long 0x0C 25. " MSK_VS_LONG_ERR ,Mask Vsync Long Error" "Enabled,Disabled" bitfld.long 0x0C 24. " MSK_VS_SHORT_ERR ,Mask Vsync Short Error" "Enabled,Disabled" textline " " bitfld.long 0x0C 16. " MSK_VS_ERR ,Mask Vsync Error" "Enabled,Disabled" bitfld.long 0x0C 9. " MSK_HS_LONG_ERR ,Mask Hsync Long Error" "Enabled,Disabled" textline " " bitfld.long 0x0C 8. " MSK_HS_SHORT_ERR ,Mask Hsync Short Error" "Enabled,Disabled" bitfld.long 0x0C 0. " MSK_HS_ERR ,Mask Hsync Error" "Enabled,Disabled" rgroup.long 0x88++0x03 line.long 0x00 "CVCNT,Capture Vertical Count register" hexmask.long.word 0x00 0.--11. 1. " CVCNT ,Capture Vertical Count" group.long 0x98++0x07 line.long 0x00 "CDCN,Capture Data Count (NTSC) register" hexmask.long.word 0x00 16.--28. 1. " BDCN ,Blanking Data Count (NTSC)" hexmask.long.word 0x00 0.--13. 1. " VDCN ,Valid Data Count (NTSC)" line.long 0x04 "CDCP,Capture Data Count (PAL) register" hexmask.long.word 0x04 16.--28. 1. " BDCP ,Blanking Data Count (PAL)" hexmask.long.word 0x04 0.--13. 1. " VDCP ,Valid Data Count (PAL)" group.long 0xA8++0x0B line.long 0x00 "MDS,Mode select register" bitfld.long 0x00 4.--5. " VCMIM ,YC Multiplex video input mode" "RGB input mode,,,YC Multiplex input mode" line.long 0x04 "CDCNS,Capture Data Count (NTSC Short)" hexmask.long.word 0x04 16.--28. 1. " BDCN_S ,Blanking Data Count (NTSC Short)" hexmask.long.word 0x04 0.--13. 1. " VDCN_S ,Valid Data Count (NTSC Short)" line.long 0x08 "CDCPS,Capture Data Count (PAL Short)" hexmask.long.word 0x08 16.--28. 1. " BDCP_S ,Blanking Data Count (PAL Short)" hexmask.long.word 0x08 0.--13. 1. " VDCP_S ,Valid Data Count (PAL Short)" rgroup.long 0xCC++0x03 line.long 0x00 "VINLC_KEP,Video Input Line Count" hexmask.long.word 0x00 0.--12. 1. " VIN_LINE_NO_KEP ,Line count of one frame (field) including the blanking period" group.long 0xD4++0x0F line.long 0x00 "VHSLS,Video Input HSYNC Long/Short register" hexmask.long.word 0x00 16.--29. 1. " VIN_HS_LONG ,Sets the video input long interval HSYNC monitoring" hexmask.long.word 0x00 0.--13. 1. " VIN_HS_SHORT ,Configures the video input short interval HSYNC monitoring" line.long 0x04 "VHSDC,Video HSYNC Down Count register" bitfld.long 0x04 31. " VIN_EHSYNC_MSK ,Video Input Error HSYNC Mask" "Disabled,Enabled" hexmask.long.byte 0x04 0.--7. 1. " VIN_HDOWN_CNT ,Configures the video input HSYNC disconnected monitoring cycle" line.long 0x08 "VVSLS,Video Input VSYNC Long/Short register" hexmask.long.word 0x08 16.--28. 1. " VIN_VS_LONG ,Sets video input long interval VSYNC monitoring" hexmask.long.word 0x08 0.--12. 1. " VIN_VS_SHORT ,Configures the video input short interval VSYNC monitoring" if (((per.l(ad:0xD0840000+0xA8))&0x30)==0x30) group.long 0xE0++0x03 line.long 0x00 "VVSDC,Video Input VSYNC Down Count register" bitfld.long 0x00 31. " VIN_EVSYNC_MSK ,Video Input Error VSYNC Mask" "0,1" hexmask.long.byte 0x00 0.--7. 1. " VIN_VDOWN_CNT ,Configures the video input VSYNC disconnected monitoring cycle" else group.long 0xE0++0x03 line.long 0x00 "VVSDC,Video Input VSYNC Down Count register" hexmask.long.byte 0x00 0.--7. 1. " VIN_VDOWN_CNT ,Configures the video input VSYNC disconnected monitoring cycle" endif group.long 0x108++0x27 line.long 0x00 "SDER,Still Detection Enable Register" hexmask.long.word 0x00 16.--26. 1. " SDMOPIX ,The number of pixels of the reduced frame n which were detected as motion pixels" rbitfld.long 0x00 3. " BF ,Bottom Field" "Top,Bottom" textline " " rbitfld.long 0x00 2. " SDMON ,Still Detection Monitor" "Interpolation,Non-interpolation" bitfld.long 0x00 1. " SDMAN ,Still Detection Manual Mode" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " SDEN ,Still Detection Enable" "Disabled,Enabled" line.long 0x04 "SDCF0,Still Detection Config register 0" hexmask.long.word 0x04 16.--24. 1. " MLC ,Maximum Line Count" hexmask.long.word 0x04 0.--10. 1. " MPC ,Maximum Pixel Count" line.long 0x08 "SDCF1,Still Detection Config register 1" hexmask.long.word 0x08 16.--26. 1. " MB ,Motion Blocks" hexmask.long.word 0x08 0.--10. 1. " MA ,The Maximum Address (MA) of reduced frame memory" line.long 0x0C "SDTH,Still Detection Threshold register" hexmask.long.tbyte 0x0C 0.--16. 1. " CBTH ,Compare Blocks Threshold value" line.long 0x10 "SDHY,Still Detection Hysteresis register" bitfld.long 0x10 24.--29. " SLB ,Still Look Back" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x10 16.--21. " MLB ,Motion Look Back" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x10 8.--13. " MO2ST ,Motion to Still switch value" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x10 0.--5. " ST2MO ,Still to Motion switch value" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x14 "HDCFG,High Definition (HD) Configuration Register" bitfld.long 0x14 5. " HD_EN_TO_DET ,Enable timeout detection" "Disabled,Enabled" bitfld.long 0x14 4. " HD_EN_ERR_DET ,Enable error detection" "Disabled,Enabled" textline " " bitfld.long 0x14 2.--3. " HD_SPREAD ,HD spread" "All AV tags are on the Y,All AV tags are on the CbCr,Alternating CbCr component,Alternating Y component" bitfld.long 0x14 1. " HD_SWAP ,HD swap" "No swap,Swap" textline " " bitfld.long 0x14 0. " HD_RUN ,HD run" "Disabled,Enabled" line.long 0x18 "HDEST,High definition Error Status Register" bitfld.long 0x18 5. " HD_L_ERR_NOL ,Long Error in Number of active lines detected" "No error,Error" bitfld.long 0x18 4. " HD_L_ERR_HACT ,Long Error in HACTIVE detected" "No error,Error" textline " " bitfld.long 0x18 3. " HD_L_ERR_HBL ,Long Error in HBLANK detected" "No error,Error" bitfld.long 0x18 2. " HD_S_ERR_NOL ,Short Error in Number of active lines detected" "No error,Error" textline " " bitfld.long 0x18 1. " HD_S_ERR_HACT ,Short Error in HACTIVE detected" "No error,Error" bitfld.long 0x18 0. " HD_S_ERR_HBL ,Short Error in HBLANK detected" "No error,Error" line.long 0x1C "HDMSK,High definition Error Mask register" bitfld.long 0x1C 5. " MSK_HD_L_ERR_NOL ,Mask register for HD_L_ERR_NOL" "Disabled,Enabled" bitfld.long 0x1C 4. " MSK_HD_L_ERR_HACT ,Mask register for HD_L_ERR_HACT" "Disabled,Enabled" textline " " bitfld.long 0x1C 3. " MSK_HD_L_ERR_HBL ,Mask register for HD_L_ERR_HBL" "Disabled,Enabled" bitfld.long 0x1C 2. " MSK_HD_S_ERR_NOL ,Mask register for HD_S_ERR_NOL" "Disabled,Enabled" textline " " bitfld.long 0x1C 1. " MSK_HD_S_ERR_HACT ,Mask register for HD_S_ERR_HACT" "Disabled,Enabled" bitfld.long 0x1C 0. " MSK_HD_S_ERR_HBL ,Mask register for HD_S_ERR_HBL" "Disabled,Enabled" line.long 0x20 "HDHBL,High definition HBLANK error detection parameter register" hexmask.long.word 0x20 16.--26. 1. " HD_L_HBL ,HBLANK long parameter to compare with. Error if frame HBLANK is larger than this value" hexmask.long.word 0x20 0.--10. 1. " HD_S_HBL ,HBLANK short parameter to compare with.Error if frame HBLANK is smaller than this value" line.long 0x24 "HDHACT,High definition HACTIVE error detection parameter register" hexmask.long.word 0x24 16.--24. 1. " HD_L_HACT ,HACTIVE long parameter to compare with Error if frame HACTIVE is larger than this value" hexmask.long.word 0x24 0.--10. 1. " HD_S_HACT ,HACTIVE short parameter to compare with Error if frame HACTIVE is smaller than this value" group.long 0x130++0x27 line.long 0x00 "HDNOL,High definition NOL (number of lines) error detection parameter register" hexmask.long.word 0x00 16.--26. 1. " HD_L_NOL ,Number of active lines long parameter" hexmask.long.word 0x00 0.--10. 1. " HD_S_NOL ,Number of active lines short parameter" line.long 0x04 "CM_COEFF_0,Color Matrix Coefficient Register 0" hexmask.long.word 0x04 0.--10. 1. " CMKY ,Coefficient for Y, same for R,G,B calculation" line.long 0x08 "CM_COEFF_1,Color Matrix Coefficient Register 1" hexmask.long.word 0x08 16.--26. 1. " CMKCBB ,Coefficient for Cb, for calculation of B value" hexmask.long.word 0x08 0.--10. 1. " CMKCBG ,Coefficient for Cb, for calculation of G value" line.long 0x0C "CM_COEFF_2,Color Matrix Coefficient Register 2" hexmask.long.word 0x0C 16.--26. 1. " CMKCRG ,Coefficient for Cr, for calculation of G value" hexmask.long.word 0x0C 0.--10. 1. " CMKCRR ,Coefficient for Cr, for calculation of R value" line.long 0x10 "SWRSTREG,Software Reset Register" bitfld.long 0x10 0. " SWRST ,Software Reset" "No reset,Reset" line.long 0x14 "WRBUFFERERROR,Write Buffer Error" eventfld.long 0x14 0. " WRBE ,Error Status" "Normal,Error" line.long 0x18 "WRBUFERRIE,Write Buffer Error Interrupt Enable" bitfld.long 0x18 0. " WRBEIE ,Enable to generate interrupt singal of buffer error. Emerald-L(MP) only" "Disabled,Enbaled" line.long 0x1C "D_YHLPF,Direct coefficient for Y component Horizontal LPF" bitfld.long 0x1C 24.--29. " K4YH ,K4 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x1C 18.--23. " K3YH ,K3 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x1C 12.--17. " K2YH ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x1C 6.--11. " K1YH ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x1C 0.--5. " K0YH ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x20 "D_CHLPF,Direct coefficient for C component Horizontal LPF" bitfld.long 0x20 24.--29. " K4CH ,K4 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x20 18.--23. " K3CH ,K3 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x20 12.--17. " K2CH ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x20 6.--11. " K1CH ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x20 0.--5. " K0CH ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x24 "D_VLPF,Direct coefficient for vertical LPF" bitfld.long 0x24 26.--30. " K2CV ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x24 21.--25. " K1CV ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x24 16.--20. " K0CV ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x24 10.--14. " K2YV ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x24 5.--9. " K1YV ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x24 0.--4. " K0YV ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x380++0x03 line.long 0x00 "CBM1,Capture Buffer Mode 1" sif (cpu()=="MB86R12") bitfld.long 0x00 20. " YRGB ,Enable YRGB format, only valid if 32bpp is used" "Disabled,Enabled" textline " " endif bitfld.long 0x00 16. " WMODE ,Weave mode" "Disabled,Enabled" bitfld.long 0x00 2. " IDMAXH ,ID max hold" "From 255 to 0,Stops at 255" textline " " bitfld.long 0x00 1. " IDRESM ,ID reset mode" "No reset,Reset" bitfld.long 0x00 0. " IDRDS ,ID read select" "Read now,Read recently" rgroup.long 0x384++0x03 line.long 0x00 "CBSTA,Capture Buffer Status" bitfld.long 0x00 16. " VALID ,Valid" "No effective,Effective" hexmask.long.byte 0x00 0.--7. 1. " IDCNT ,ID count" group.long 0x388++0x03 line.long 0x00 "CBA2,Capture Buffer Address 2" hexmask.long 0x00 4.--31. 0x10 " CBA2 ,The first address in a new area when the swap of the capture buffer is executed is set" rgroup.long 0x38C++0x03 line.long 0x00 "CBA3,Capture Buffer Address 3" group.long 0x390++0x07 line.long 0x00 "CBSWS,Capture Buffer Swap Select" bitfld.long 0x00 3. " CBSWS3 ,Capture buffer swap select 3" "Not selected,Selected" bitfld.long 0x00 2. " CBSWS2 ,Capture buffer swap select 2" "Not selected,Selected" textline " " bitfld.long 0x00 2. " CBSWS1 ,Capture buffer swap select 1" "Not selected,Selected" bitfld.long 0x00 0. " CBSWS0 ,Capture buffer swap select 0" "Not selected,Selected" line.long 0x04 "CBSWP,Capture Buffer Swap" width 0xb tree.end tree "CAP2" base ad:0xD0850000 width 15. group.long 0x00++0x3B line.long 0x00 "VCM,Video Capture Mode register" bitfld.long 0x00 31. " VIE ,Video Input Capture Enable" "Disabled,Enabled" bitfld.long 0x00 29.--30. " VIS ,Video Input Format Select" "ITU BT 656 input select,HD 720p input select,RGB input select," textline " " bitfld.long 0x00 28. " VICE ,Video Input Clock Enable" "Disabled,Enabled" sif (cpu()=="MB86R11F") bitfld.long 0x00 26.--27. " A_MSB ,MSB Address bits 29-28 of the capture unit address" "0 to 256MByte,256MByte to 512MByte,512MByte to 768MByte,768MByte to 1GByte" endif textline " " bitfld.long 0x00 24.--25. " CM ,Capture Mode register" "Capture mode,,,Capture" textline " " bitfld.long 0x00 20. " VI ,Vertical Interpolation" "On,Off" bitfld.long 0x00 14.--19. " VDSS_VDMS ,Video Data Mode Select" "RGB_888,,RGB_888_A0,,RGB_666_0,,RGB_888_A1,,RGB_666_1,,RGB_666_A0,,ITU_656_0_P,ITU_656_0_N,RGB_666_A1,,ITU_656_1_P,ITU_656_1_N,,,ITU_656_2_P,ITU_656_2_N,ITU_656_1_A1,,ITU_656_3_P,ITU_656_3_P_N,HD_SDR16_0A0,,HD_DDR8_0,HD_SDR8_0,HD_SDR16_0A1,,HD_DDR8_1,HD_SDR8_1,,,HD_DDR8_2,HD_SDR8_2,,,HD_DDR8_3,HD_SDR8_3,,,HD_SDR16_0,..." textline " " bitfld.long 0x00 11. " VF ,Input Video Format Select" "ITU-R BT 656,YC multiplex" bitfld.long 0x00 4. " DSEL ,Select the display unit for video output" "Display 0,Display 1" textline " " bitfld.long 0x00 2. " NRGB ,Native RGB input on, native RGB input is set" "RGB to YUV 422 mode,RGB mode" bitfld.long 0x00 1. " VS ,Video Select" "NTSC,PAL" line.long 0x04 "CSC,Capture Scale register" bitfld.long 0x04 27.--31. " VSCI ,Vertical Scale Integer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.word 0x04 16.--26. 1. " VSCF ,Vertical Scale Fraction" textline " " bitfld.long 0x04 11.--15. " HSCI ,Horizontal Scale Integer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.word 0x04 0.--10. 1. " HSCF ,Horizontal Scale Fraction" line.long 0x08 "VCS,Video Capture Status 0 register" textline " " bitfld.long 0x08 6. " CE_[6] ,ITU-R 656 short term H code error (EAV)" "No error,Error" bitfld.long 0x08 5. " [5] ,ITU-R 656 short term H code error (SAV)" "No error,Error" bitfld.long 0x08 4. " [4] ,ITU-R 656 long term H code error (EAV)" "No error,Error" bitfld.long 0x08 3. " [3] ,ITU-R 656 long term H code error (SAV)" "No error,Error" textline " " bitfld.long 0x08 2. " [2] ,ITU-R 656 undefined error (Code Bit7-0) " "No error,Error" bitfld.long 0x08 1. " [1] ,ITU-R 656 undefined error (Code Bit7-4)" "No error,Error" bitfld.long 0x08 0. " [0] ,ITU-R 656 undefined error (Code Bit7)" "No error,Error" textline " " line.long 0x0C "VCS_MSK,Video Capture Status 0 Mask register" bitfld.long 0x0C 6. " MSK_ERR6 ,Code Error 6 Mask" "Masked,Not masked" bitfld.long 0x0C 5. " MSK_ERR5 ,Code Error 5 Mask" "Masked,Not masked" textline " " bitfld.long 0x0C 4. " MSK_ERR4 ,Code Error 4 Mask" "Masked,Not masked" bitfld.long 0x0C 3. " MSK_ERR3 ,Code Error 3 Mask" "Masked,Not masked" textline " " bitfld.long 0x0C 2. " MSK_ERR2 ,Code Error 2 Mask" "Masked,Not masked" bitfld.long 0x0C 1. " MSK_ERR1 ,Code Error 1 Mask" "Masked,Not masked" textline " " bitfld.long 0x0C 0. " MSK_ERR0 ,Code Error 0 Mask" "Masked,Not masked" line.long 0x10 "CBM0,Video Capture Buffer Mode 0 register" bitfld.long 0x10 31. " OO ,Odd Only Mode" "Normal Mode,Capture odd fields only" bitfld.long 0x10 30. " SBUF ,Single Buffer" "Normal Mode,Single Buffer Mode" textline " " bitfld.long 0x10 29. " CRGB ,Conversion to RGB" "Disabled,Enabled" hexmask.long.byte 0x10 16.--23. 1. " CBW ,Capture Buffer Memory Width" textline " " bitfld.long 0x10 15. " BLEN ,Blending Enable" "Disabled,Enabled" bitfld.long 0x10 14. " C24 ,Color 24bit/pixel" "16 bits/pixel,24 bits/pixel" textline " " bitfld.long 0x10 12.--13. " RGBA ,Configure RGBA component order" "ARGB,RGBA,ABGR,RGB565" bitfld.long 0x10 0. " CBST ,Capture Burst Mode" "Normal,Long" line.long 0x14 "CBA0,Video Capture Buffer 0 Address register" hexmask.long 0x14 3.--31. 0x08 " CBOA ,Video Capture Buffer Origin Address" line.long 0x18 "CBA1,Video Capture Buffer 1 Address register" hexmask.long 0x18 3.--31. 0x08 " CBLA ,Video Capture Buffer Limit Address" line.long 0x1C "CISTR,Capture Image Start register" hexmask.long.word 0x1C 16.--27. 1. " CIVSTR0 ,Capture Image Vertical Start" hexmask.long.word 0x1C 0.--11. 1. " CIHSTR ,Capture Image Horizontal start" line.long 0x20 "CIEND,Capture Image End register" hexmask.long.word 0x20 16.--27. 1. " CIVEND0 ,Capture Image Vertical End 0" hexmask.long.word 0x20 0.--11. 1. " CIHEND ,Capture Image Horizontal End 0" line.long 0x24 "CISEO,Capture Image Start End Optional register" hexmask.long.word 0x24 16.--27. 1. " CIVEND1 ,Capture Image Vertical End 1" hexmask.long.word 0x24 0.--11. 1. " CIVSTR1 ,Capture Image Vertical Start 1" line.long 0x28 "CHP,Capture Horizontal Pixel register" hexmask.long.word 0x28 0.--9. 1. " CHP ,Capture Horizontal Pixel" line.long 0x2C "CVP,Capture Vertical Pixel register" hexmask.long.word 0x2C 16.--25. 1. " CVPP ,Capture Vertical Pixel for PAL" hexmask.long.word 0x2C 0.--9. 1. " CVPN ,Capture Vertical Pixel for NTSC" line.long 0x30 "CLPF,Capture Low-Pass Filters register" bitfld.long 0x30 24.--27. " CVLPF ,Capture Vertical LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x30 16.--19. " CHLPF ,Capture Horizontal LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x34 "CMSS,Capture Magnify Source Size register" hexmask.long.word 0x34 16.--25. 1. " CMSHP ,Capture Magnify Source Horizontal Pixel" hexmask.long.word 0x34 0.--9. 1. " CMSVL ,Capture Magnify Source Vertical Line" line.long 0x38 "CMDS,Capture Magnify Destination Size register" hexmask.long.word 0x38 16.--26. 1. " CMDHP ,Capture Magnify Destination Horizontal Pixel" hexmask.long.word 0x38 0.--9. 1. " CMDVL ,Capture Magnify Destination Vertical Line" group.long 0x48++0x23 line.long 0x00 "RGBHC,RGB input HSYNC cycle register" hexmask.long.word 0x00 0.--13. 1. " RGBHC ,Sets the horizontal cycle (HSYNC) time when RGB mode is used" line.long 0x04 "RGBHEN,RGB input horizontal enable area register" hexmask.long.word 0x04 16.--27. 1. " RGBHST ,Configures the start position of effective pixel data" hexmask.long.word 0x04 0.--12. 1. " RGBHEN ,Sets the effective pixel data size per pixel" line.long 0x08 "RGBVEN,RGB input vertical enable area register" bitfld.long 0x08 28.--29. " RGBVST_T_O ,RGB input Vertical Enable area start position for odd fields" "0,1,2,3" hexmask.long.word 0x08 16.--24. 1. " RGBVST ,RGB input Vertical Enable area Size" textline " " hexmask.long.word 0x08 0.--12. 1. " RGBVEN ,RGB input Vertical Enable area size" line.long 0x0C "VIN_VSAMP,Video Input VSYNC Sampling mode register" bitfld.long 0x0C 8.--9. " VJITFLT ,Jitter Filter configuration" "Samples on HSYNC,,," bitfld.long 0x0C 0. " FLDREV ,Field Reverse, inverts the logic of the CAP0FID input" "Disabled,Enabled" line.long 0x10 "RGBS,RGB input sync register" bitfld.long 0x10 16. " RM ,RGB input mode select" ",RGB direct input mode" bitfld.long 0x10 1. " HP ,HSYNC Polarity" "Falling edge,Rising edge" textline " " bitfld.long 0x10 0. " VP ,VINSYNC Polarity" "Falling edge,Rising edge" line.long 0x14 "RGBCMY,RGB Color Conversion Matrix Y coefficient register" hexmask.long.word 0x14 22.--31. 1. " A11 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x14 11.--20. 1. " A12 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x14 0.--9. 1. " A13 ,10 bit signed value, the lower 8 bits are the fractional part" line.long 0x18 "RGBCMCB,RGB Color Convert Matrix Cb coefficient register" hexmask.long.word 0x18 22.--31. 1. " A21 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x18 11.--20. 1. " A22 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x18 0.--9. 1. " A23 ,10 bit signed value, the lower 8 bits are the fractional part" line.long 0x1C "RGBCMCR,RGB Color Convert Matrix Cr coefficient register" hexmask.long.word 0x1C 22.--31. 1. " A31 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x1C 11.--20. 1. " A32 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x1C 0.--9. 1. " A33 ,10 bit signed value, the lower 8 bits are the fractional part" line.long 0x20 "RGBCMB,RGB Color Convert Matrix b coefficient register" hexmask.long.word 0x20 22.--30. 1. " B1 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x20 11.--19. 1. " B2 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x20 0.--8. 1. " B3 ,10 bit signed value, the lower 8 bits are the fractional part" group.long 0x78++0x0F line.long 0x00 "CINT,Capture interrupt register" bitfld.long 0x00 1. " IVS ,VS (VSYNC) Interrupt" "No interrupt,Interrupt" line.long 0x04 "CINTMSK,Capture Interrupt Mask register" bitfld.long 0x04 4. " DIRECT_INT ,Feeds VSYNC to the interrupt line" "Standard interrupt,Direct Interrupt" bitfld.long 0x04 2.--3. " MSK_FIELD ,Mask the VS interrupt for top or bottom field" "Not masked,Top field,Bottom field," textline " " bitfld.long 0x04 1. " MSK_VSI ,Mask VS (VSYNC) Interrupt" "Disabled,Active" line.long 0x08 "SYNC_ERR,Synchronisation error register" bitfld.long 0x08 25. " VS_LONG_ERR ,Vsync Long Error" "No error,Error" bitfld.long 0x08 24. " VS_SHORT_ERR ,Vsync Short Error" "No error,Error" textline " " bitfld.long 0x08 16. " VS_ERR ,Vsync Error(disconnected)" "No error,Error" bitfld.long 0x08 9. " HS_LONG_ERR ,Hsync Long Error" "No error,Error" textline " " bitfld.long 0x08 8. " HS_SHORT_ERR ,Hsync Short Error" "No error,Error" bitfld.long 0x08 0. " HS_ERR ,Hsync Error(disconnected)" "No error,Error" line.long 0x0C "SYNC_ERR_MSK,Synchronisation Error Mask register" bitfld.long 0x0C 25. " MSK_VS_LONG_ERR ,Mask Vsync Long Error" "Enabled,Disabled" bitfld.long 0x0C 24. " MSK_VS_SHORT_ERR ,Mask Vsync Short Error" "Enabled,Disabled" textline " " bitfld.long 0x0C 16. " MSK_VS_ERR ,Mask Vsync Error" "Enabled,Disabled" bitfld.long 0x0C 9. " MSK_HS_LONG_ERR ,Mask Hsync Long Error" "Enabled,Disabled" textline " " bitfld.long 0x0C 8. " MSK_HS_SHORT_ERR ,Mask Hsync Short Error" "Enabled,Disabled" bitfld.long 0x0C 0. " MSK_HS_ERR ,Mask Hsync Error" "Enabled,Disabled" rgroup.long 0x88++0x03 line.long 0x00 "CVCNT,Capture Vertical Count register" hexmask.long.word 0x00 0.--11. 1. " CVCNT ,Capture Vertical Count" group.long 0x98++0x07 line.long 0x00 "CDCN,Capture Data Count (NTSC) register" hexmask.long.word 0x00 16.--28. 1. " BDCN ,Blanking Data Count (NTSC)" hexmask.long.word 0x00 0.--13. 1. " VDCN ,Valid Data Count (NTSC)" line.long 0x04 "CDCP,Capture Data Count (PAL) register" hexmask.long.word 0x04 16.--28. 1. " BDCP ,Blanking Data Count (PAL)" hexmask.long.word 0x04 0.--13. 1. " VDCP ,Valid Data Count (PAL)" group.long 0xA8++0x0B line.long 0x00 "MDS,Mode select register" bitfld.long 0x00 4.--5. " VCMIM ,YC Multiplex video input mode" "RGB input mode,,,YC Multiplex input mode" line.long 0x04 "CDCNS,Capture Data Count (NTSC Short)" hexmask.long.word 0x04 16.--28. 1. " BDCN_S ,Blanking Data Count (NTSC Short)" hexmask.long.word 0x04 0.--13. 1. " VDCN_S ,Valid Data Count (NTSC Short)" line.long 0x08 "CDCPS,Capture Data Count (PAL Short)" hexmask.long.word 0x08 16.--28. 1. " BDCP_S ,Blanking Data Count (PAL Short)" hexmask.long.word 0x08 0.--13. 1. " VDCP_S ,Valid Data Count (PAL Short)" rgroup.long 0xCC++0x03 line.long 0x00 "VINLC_KEP,Video Input Line Count" hexmask.long.word 0x00 0.--12. 1. " VIN_LINE_NO_KEP ,Line count of one frame (field) including the blanking period" group.long 0xD4++0x0F line.long 0x00 "VHSLS,Video Input HSYNC Long/Short register" hexmask.long.word 0x00 16.--29. 1. " VIN_HS_LONG ,Sets the video input long interval HSYNC monitoring" hexmask.long.word 0x00 0.--13. 1. " VIN_HS_SHORT ,Configures the video input short interval HSYNC monitoring" line.long 0x04 "VHSDC,Video HSYNC Down Count register" bitfld.long 0x04 31. " VIN_EHSYNC_MSK ,Video Input Error HSYNC Mask" "Disabled,Enabled" hexmask.long.byte 0x04 0.--7. 1. " VIN_HDOWN_CNT ,Configures the video input HSYNC disconnected monitoring cycle" line.long 0x08 "VVSLS,Video Input VSYNC Long/Short register" hexmask.long.word 0x08 16.--28. 1. " VIN_VS_LONG ,Sets video input long interval VSYNC monitoring" hexmask.long.word 0x08 0.--12. 1. " VIN_VS_SHORT ,Configures the video input short interval VSYNC monitoring" if (((per.l(ad:0xD0850000+0xA8))&0x30)==0x30) group.long 0xE0++0x03 line.long 0x00 "VVSDC,Video Input VSYNC Down Count register" bitfld.long 0x00 31. " VIN_EVSYNC_MSK ,Video Input Error VSYNC Mask" "0,1" hexmask.long.byte 0x00 0.--7. 1. " VIN_VDOWN_CNT ,Configures the video input VSYNC disconnected monitoring cycle" else group.long 0xE0++0x03 line.long 0x00 "VVSDC,Video Input VSYNC Down Count register" hexmask.long.byte 0x00 0.--7. 1. " VIN_VDOWN_CNT ,Configures the video input VSYNC disconnected monitoring cycle" endif group.long 0x108++0x27 line.long 0x00 "SDER,Still Detection Enable Register" hexmask.long.word 0x00 16.--26. 1. " SDMOPIX ,The number of pixels of the reduced frame n which were detected as motion pixels" rbitfld.long 0x00 3. " BF ,Bottom Field" "Top,Bottom" textline " " rbitfld.long 0x00 2. " SDMON ,Still Detection Monitor" "Interpolation,Non-interpolation" bitfld.long 0x00 1. " SDMAN ,Still Detection Manual Mode" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " SDEN ,Still Detection Enable" "Disabled,Enabled" line.long 0x04 "SDCF0,Still Detection Config register 0" hexmask.long.word 0x04 16.--24. 1. " MLC ,Maximum Line Count" hexmask.long.word 0x04 0.--10. 1. " MPC ,Maximum Pixel Count" line.long 0x08 "SDCF1,Still Detection Config register 1" hexmask.long.word 0x08 16.--26. 1. " MB ,Motion Blocks" hexmask.long.word 0x08 0.--10. 1. " MA ,The Maximum Address (MA) of reduced frame memory" line.long 0x0C "SDTH,Still Detection Threshold register" hexmask.long.tbyte 0x0C 0.--16. 1. " CBTH ,Compare Blocks Threshold value" line.long 0x10 "SDHY,Still Detection Hysteresis register" bitfld.long 0x10 24.--29. " SLB ,Still Look Back" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x10 16.--21. " MLB ,Motion Look Back" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x10 8.--13. " MO2ST ,Motion to Still switch value" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x10 0.--5. " ST2MO ,Still to Motion switch value" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x14 "HDCFG,High Definition (HD) Configuration Register" bitfld.long 0x14 5. " HD_EN_TO_DET ,Enable timeout detection" "Disabled,Enabled" bitfld.long 0x14 4. " HD_EN_ERR_DET ,Enable error detection" "Disabled,Enabled" textline " " bitfld.long 0x14 2.--3. " HD_SPREAD ,HD spread" "All AV tags are on the Y,All AV tags are on the CbCr,Alternating CbCr component,Alternating Y component" bitfld.long 0x14 1. " HD_SWAP ,HD swap" "No swap,Swap" textline " " bitfld.long 0x14 0. " HD_RUN ,HD run" "Disabled,Enabled" line.long 0x18 "HDEST,High definition Error Status Register" bitfld.long 0x18 5. " HD_L_ERR_NOL ,Long Error in Number of active lines detected" "No error,Error" bitfld.long 0x18 4. " HD_L_ERR_HACT ,Long Error in HACTIVE detected" "No error,Error" textline " " bitfld.long 0x18 3. " HD_L_ERR_HBL ,Long Error in HBLANK detected" "No error,Error" bitfld.long 0x18 2. " HD_S_ERR_NOL ,Short Error in Number of active lines detected" "No error,Error" textline " " bitfld.long 0x18 1. " HD_S_ERR_HACT ,Short Error in HACTIVE detected" "No error,Error" bitfld.long 0x18 0. " HD_S_ERR_HBL ,Short Error in HBLANK detected" "No error,Error" line.long 0x1C "HDMSK,High definition Error Mask register" bitfld.long 0x1C 5. " MSK_HD_L_ERR_NOL ,Mask register for HD_L_ERR_NOL" "Disabled,Enabled" bitfld.long 0x1C 4. " MSK_HD_L_ERR_HACT ,Mask register for HD_L_ERR_HACT" "Disabled,Enabled" textline " " bitfld.long 0x1C 3. " MSK_HD_L_ERR_HBL ,Mask register for HD_L_ERR_HBL" "Disabled,Enabled" bitfld.long 0x1C 2. " MSK_HD_S_ERR_NOL ,Mask register for HD_S_ERR_NOL" "Disabled,Enabled" textline " " bitfld.long 0x1C 1. " MSK_HD_S_ERR_HACT ,Mask register for HD_S_ERR_HACT" "Disabled,Enabled" bitfld.long 0x1C 0. " MSK_HD_S_ERR_HBL ,Mask register for HD_S_ERR_HBL" "Disabled,Enabled" line.long 0x20 "HDHBL,High definition HBLANK error detection parameter register" hexmask.long.word 0x20 16.--26. 1. " HD_L_HBL ,HBLANK long parameter to compare with. Error if frame HBLANK is larger than this value" hexmask.long.word 0x20 0.--10. 1. " HD_S_HBL ,HBLANK short parameter to compare with.Error if frame HBLANK is smaller than this value" line.long 0x24 "HDHACT,High definition HACTIVE error detection parameter register" hexmask.long.word 0x24 16.--24. 1. " HD_L_HACT ,HACTIVE long parameter to compare with Error if frame HACTIVE is larger than this value" hexmask.long.word 0x24 0.--10. 1. " HD_S_HACT ,HACTIVE short parameter to compare with Error if frame HACTIVE is smaller than this value" group.long 0x130++0x27 line.long 0x00 "HDNOL,High definition NOL (number of lines) error detection parameter register" hexmask.long.word 0x00 16.--26. 1. " HD_L_NOL ,Number of active lines long parameter" hexmask.long.word 0x00 0.--10. 1. " HD_S_NOL ,Number of active lines short parameter" line.long 0x04 "CM_COEFF_0,Color Matrix Coefficient Register 0" hexmask.long.word 0x04 0.--10. 1. " CMKY ,Coefficient for Y, same for R,G,B calculation" line.long 0x08 "CM_COEFF_1,Color Matrix Coefficient Register 1" hexmask.long.word 0x08 16.--26. 1. " CMKCBB ,Coefficient for Cb, for calculation of B value" hexmask.long.word 0x08 0.--10. 1. " CMKCBG ,Coefficient for Cb, for calculation of G value" line.long 0x0C "CM_COEFF_2,Color Matrix Coefficient Register 2" hexmask.long.word 0x0C 16.--26. 1. " CMKCRG ,Coefficient for Cr, for calculation of G value" hexmask.long.word 0x0C 0.--10. 1. " CMKCRR ,Coefficient for Cr, for calculation of R value" line.long 0x10 "SWRSTREG,Software Reset Register" bitfld.long 0x10 0. " SWRST ,Software Reset" "No reset,Reset" line.long 0x14 "WRBUFFERERROR,Write Buffer Error" eventfld.long 0x14 0. " WRBE ,Error Status" "Normal,Error" line.long 0x18 "WRBUFERRIE,Write Buffer Error Interrupt Enable" bitfld.long 0x18 0. " WRBEIE ,Enable to generate interrupt singal of buffer error. Emerald-L(MP) only" "Disabled,Enbaled" line.long 0x1C "D_YHLPF,Direct coefficient for Y component Horizontal LPF" bitfld.long 0x1C 24.--29. " K4YH ,K4 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x1C 18.--23. " K3YH ,K3 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x1C 12.--17. " K2YH ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x1C 6.--11. " K1YH ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x1C 0.--5. " K0YH ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x20 "D_CHLPF,Direct coefficient for C component Horizontal LPF" bitfld.long 0x20 24.--29. " K4CH ,K4 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x20 18.--23. " K3CH ,K3 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x20 12.--17. " K2CH ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x20 6.--11. " K1CH ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x20 0.--5. " K0CH ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x24 "D_VLPF,Direct coefficient for vertical LPF" bitfld.long 0x24 26.--30. " K2CV ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x24 21.--25. " K1CV ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x24 16.--20. " K0CV ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x24 10.--14. " K2YV ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x24 5.--9. " K1YV ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x24 0.--4. " K0YV ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x380++0x03 line.long 0x00 "CBM1,Capture Buffer Mode 1" sif (cpu()=="MB86R12") bitfld.long 0x00 20. " YRGB ,Enable YRGB format, only valid if 32bpp is used" "Disabled,Enabled" textline " " endif bitfld.long 0x00 16. " WMODE ,Weave mode" "Disabled,Enabled" bitfld.long 0x00 2. " IDMAXH ,ID max hold" "From 255 to 0,Stops at 255" textline " " bitfld.long 0x00 1. " IDRESM ,ID reset mode" "No reset,Reset" bitfld.long 0x00 0. " IDRDS ,ID read select" "Read now,Read recently" rgroup.long 0x384++0x03 line.long 0x00 "CBSTA,Capture Buffer Status" bitfld.long 0x00 16. " VALID ,Valid" "No effective,Effective" hexmask.long.byte 0x00 0.--7. 1. " IDCNT ,ID count" group.long 0x388++0x03 line.long 0x00 "CBA2,Capture Buffer Address 2" hexmask.long 0x00 4.--31. 0x10 " CBA2 ,The first address in a new area when the swap of the capture buffer is executed is set" rgroup.long 0x38C++0x03 line.long 0x00 "CBA3,Capture Buffer Address 3" group.long 0x390++0x07 line.long 0x00 "CBSWS,Capture Buffer Swap Select" bitfld.long 0x00 3. " CBSWS3 ,Capture buffer swap select 3" "Not selected,Selected" bitfld.long 0x00 2. " CBSWS2 ,Capture buffer swap select 2" "Not selected,Selected" textline " " bitfld.long 0x00 2. " CBSWS1 ,Capture buffer swap select 1" "Not selected,Selected" bitfld.long 0x00 0. " CBSWS0 ,Capture buffer swap select 0" "Not selected,Selected" line.long 0x04 "CBSWP,Capture Buffer Swap" width 0xb tree.end tree "CAP3" base ad:0xD0860000 width 15. group.long 0x00++0x3B line.long 0x00 "VCM,Video Capture Mode register" bitfld.long 0x00 31. " VIE ,Video Input Capture Enable" "Disabled,Enabled" bitfld.long 0x00 29.--30. " VIS ,Video Input Format Select" "ITU BT 656 input select,HD 720p input select,RGB input select," textline " " bitfld.long 0x00 28. " VICE ,Video Input Clock Enable" "Disabled,Enabled" sif (cpu()=="MB86R11F") bitfld.long 0x00 26.--27. " A_MSB ,MSB Address bits 29-28 of the capture unit address" "0 to 256MByte,256MByte to 512MByte,512MByte to 768MByte,768MByte to 1GByte" endif textline " " bitfld.long 0x00 24.--25. " CM ,Capture Mode register" "Capture mode,,,Capture" textline " " bitfld.long 0x00 20. " VI ,Vertical Interpolation" "On,Off" bitfld.long 0x00 14.--19. " VDSS_VDMS ,Video Data Mode Select" "RGB_888,,RGB_888_A0,,RGB_666_0,,RGB_888_A1,,RGB_666_1,,RGB_666_A0,,ITU_656_0_P,ITU_656_0_N,RGB_666_A1,,ITU_656_1_P,ITU_656_1_N,,,ITU_656_2_P,ITU_656_2_N,ITU_656_1_A1,,ITU_656_3_P,ITU_656_3_P_N,HD_SDR16_0A0,,HD_DDR8_0,HD_SDR8_0,HD_SDR16_0A1,,HD_DDR8_1,HD_SDR8_1,,,HD_DDR8_2,HD_SDR8_2,,,HD_DDR8_3,HD_SDR8_3,,,HD_SDR16_0,..." textline " " bitfld.long 0x00 11. " VF ,Input Video Format Select" "ITU-R BT 656,YC multiplex" bitfld.long 0x00 4. " DSEL ,Select the display unit for video output" "Display 0,Display 1" textline " " bitfld.long 0x00 2. " NRGB ,Native RGB input on, native RGB input is set" "RGB to YUV 422 mode,RGB mode" bitfld.long 0x00 1. " VS ,Video Select" "NTSC,PAL" line.long 0x04 "CSC,Capture Scale register" bitfld.long 0x04 27.--31. " VSCI ,Vertical Scale Integer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.word 0x04 16.--26. 1. " VSCF ,Vertical Scale Fraction" textline " " bitfld.long 0x04 11.--15. " HSCI ,Horizontal Scale Integer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.word 0x04 0.--10. 1. " HSCF ,Horizontal Scale Fraction" line.long 0x08 "VCS,Video Capture Status 0 register" textline " " bitfld.long 0x08 6. " CE_[6] ,ITU-R 656 short term H code error (EAV)" "No error,Error" bitfld.long 0x08 5. " [5] ,ITU-R 656 short term H code error (SAV)" "No error,Error" bitfld.long 0x08 4. " [4] ,ITU-R 656 long term H code error (EAV)" "No error,Error" bitfld.long 0x08 3. " [3] ,ITU-R 656 long term H code error (SAV)" "No error,Error" textline " " bitfld.long 0x08 2. " [2] ,ITU-R 656 undefined error (Code Bit7-0) " "No error,Error" bitfld.long 0x08 1. " [1] ,ITU-R 656 undefined error (Code Bit7-4)" "No error,Error" bitfld.long 0x08 0. " [0] ,ITU-R 656 undefined error (Code Bit7)" "No error,Error" textline " " line.long 0x0C "VCS_MSK,Video Capture Status 0 Mask register" bitfld.long 0x0C 6. " MSK_ERR6 ,Code Error 6 Mask" "Masked,Not masked" bitfld.long 0x0C 5. " MSK_ERR5 ,Code Error 5 Mask" "Masked,Not masked" textline " " bitfld.long 0x0C 4. " MSK_ERR4 ,Code Error 4 Mask" "Masked,Not masked" bitfld.long 0x0C 3. " MSK_ERR3 ,Code Error 3 Mask" "Masked,Not masked" textline " " bitfld.long 0x0C 2. " MSK_ERR2 ,Code Error 2 Mask" "Masked,Not masked" bitfld.long 0x0C 1. " MSK_ERR1 ,Code Error 1 Mask" "Masked,Not masked" textline " " bitfld.long 0x0C 0. " MSK_ERR0 ,Code Error 0 Mask" "Masked,Not masked" line.long 0x10 "CBM0,Video Capture Buffer Mode 0 register" bitfld.long 0x10 31. " OO ,Odd Only Mode" "Normal Mode,Capture odd fields only" bitfld.long 0x10 30. " SBUF ,Single Buffer" "Normal Mode,Single Buffer Mode" textline " " bitfld.long 0x10 29. " CRGB ,Conversion to RGB" "Disabled,Enabled" hexmask.long.byte 0x10 16.--23. 1. " CBW ,Capture Buffer Memory Width" textline " " bitfld.long 0x10 15. " BLEN ,Blending Enable" "Disabled,Enabled" bitfld.long 0x10 14. " C24 ,Color 24bit/pixel" "16 bits/pixel,24 bits/pixel" textline " " bitfld.long 0x10 12.--13. " RGBA ,Configure RGBA component order" "ARGB,RGBA,ABGR,RGB565" bitfld.long 0x10 0. " CBST ,Capture Burst Mode" "Normal,Long" line.long 0x14 "CBA0,Video Capture Buffer 0 Address register" hexmask.long 0x14 3.--31. 0x08 " CBOA ,Video Capture Buffer Origin Address" line.long 0x18 "CBA1,Video Capture Buffer 1 Address register" hexmask.long 0x18 3.--31. 0x08 " CBLA ,Video Capture Buffer Limit Address" line.long 0x1C "CISTR,Capture Image Start register" hexmask.long.word 0x1C 16.--27. 1. " CIVSTR0 ,Capture Image Vertical Start" hexmask.long.word 0x1C 0.--11. 1. " CIHSTR ,Capture Image Horizontal start" line.long 0x20 "CIEND,Capture Image End register" hexmask.long.word 0x20 16.--27. 1. " CIVEND0 ,Capture Image Vertical End 0" hexmask.long.word 0x20 0.--11. 1. " CIHEND ,Capture Image Horizontal End 0" line.long 0x24 "CISEO,Capture Image Start End Optional register" hexmask.long.word 0x24 16.--27. 1. " CIVEND1 ,Capture Image Vertical End 1" hexmask.long.word 0x24 0.--11. 1. " CIVSTR1 ,Capture Image Vertical Start 1" line.long 0x28 "CHP,Capture Horizontal Pixel register" hexmask.long.word 0x28 0.--9. 1. " CHP ,Capture Horizontal Pixel" line.long 0x2C "CVP,Capture Vertical Pixel register" hexmask.long.word 0x2C 16.--25. 1. " CVPP ,Capture Vertical Pixel for PAL" hexmask.long.word 0x2C 0.--9. 1. " CVPN ,Capture Vertical Pixel for NTSC" line.long 0x30 "CLPF,Capture Low-Pass Filters register" bitfld.long 0x30 24.--27. " CVLPF ,Capture Vertical LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x30 16.--19. " CHLPF ,Capture Horizontal LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x34 "CMSS,Capture Magnify Source Size register" hexmask.long.word 0x34 16.--25. 1. " CMSHP ,Capture Magnify Source Horizontal Pixel" hexmask.long.word 0x34 0.--9. 1. " CMSVL ,Capture Magnify Source Vertical Line" line.long 0x38 "CMDS,Capture Magnify Destination Size register" hexmask.long.word 0x38 16.--26. 1. " CMDHP ,Capture Magnify Destination Horizontal Pixel" hexmask.long.word 0x38 0.--9. 1. " CMDVL ,Capture Magnify Destination Vertical Line" group.long 0x48++0x23 line.long 0x00 "RGBHC,RGB input HSYNC cycle register" hexmask.long.word 0x00 0.--13. 1. " RGBHC ,Sets the horizontal cycle (HSYNC) time when RGB mode is used" line.long 0x04 "RGBHEN,RGB input horizontal enable area register" hexmask.long.word 0x04 16.--27. 1. " RGBHST ,Configures the start position of effective pixel data" hexmask.long.word 0x04 0.--12. 1. " RGBHEN ,Sets the effective pixel data size per pixel" line.long 0x08 "RGBVEN,RGB input vertical enable area register" bitfld.long 0x08 28.--29. " RGBVST_T_O ,RGB input Vertical Enable area start position for odd fields" "0,1,2,3" hexmask.long.word 0x08 16.--24. 1. " RGBVST ,RGB input Vertical Enable area Size" textline " " hexmask.long.word 0x08 0.--12. 1. " RGBVEN ,RGB input Vertical Enable area size" line.long 0x0C "VIN_VSAMP,Video Input VSYNC Sampling mode register" bitfld.long 0x0C 8.--9. " VJITFLT ,Jitter Filter configuration" "Samples on HSYNC,,," bitfld.long 0x0C 0. " FLDREV ,Field Reverse, inverts the logic of the CAP0FID input" "Disabled,Enabled" line.long 0x10 "RGBS,RGB input sync register" bitfld.long 0x10 16. " RM ,RGB input mode select" ",RGB direct input mode" bitfld.long 0x10 1. " HP ,HSYNC Polarity" "Falling edge,Rising edge" textline " " bitfld.long 0x10 0. " VP ,VINSYNC Polarity" "Falling edge,Rising edge" line.long 0x14 "RGBCMY,RGB Color Conversion Matrix Y coefficient register" hexmask.long.word 0x14 22.--31. 1. " A11 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x14 11.--20. 1. " A12 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x14 0.--9. 1. " A13 ,10 bit signed value, the lower 8 bits are the fractional part" line.long 0x18 "RGBCMCB,RGB Color Convert Matrix Cb coefficient register" hexmask.long.word 0x18 22.--31. 1. " A21 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x18 11.--20. 1. " A22 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x18 0.--9. 1. " A23 ,10 bit signed value, the lower 8 bits are the fractional part" line.long 0x1C "RGBCMCR,RGB Color Convert Matrix Cr coefficient register" hexmask.long.word 0x1C 22.--31. 1. " A31 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x1C 11.--20. 1. " A32 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x1C 0.--9. 1. " A33 ,10 bit signed value, the lower 8 bits are the fractional part" line.long 0x20 "RGBCMB,RGB Color Convert Matrix b coefficient register" hexmask.long.word 0x20 22.--30. 1. " B1 ,10 bit signed value, the lower 8 bits are the fractional part" hexmask.long.word 0x20 11.--19. 1. " B2 ,10 bit signed value, the lower 8 bits are the fractional part" textline " " hexmask.long.word 0x20 0.--8. 1. " B3 ,10 bit signed value, the lower 8 bits are the fractional part" group.long 0x78++0x0F line.long 0x00 "CINT,Capture interrupt register" bitfld.long 0x00 1. " IVS ,VS (VSYNC) Interrupt" "No interrupt,Interrupt" line.long 0x04 "CINTMSK,Capture Interrupt Mask register" bitfld.long 0x04 4. " DIRECT_INT ,Feeds VSYNC to the interrupt line" "Standard interrupt,Direct Interrupt" bitfld.long 0x04 2.--3. " MSK_FIELD ,Mask the VS interrupt for top or bottom field" "Not masked,Top field,Bottom field," textline " " bitfld.long 0x04 1. " MSK_VSI ,Mask VS (VSYNC) Interrupt" "Disabled,Active" line.long 0x08 "SYNC_ERR,Synchronisation error register" bitfld.long 0x08 25. " VS_LONG_ERR ,Vsync Long Error" "No error,Error" bitfld.long 0x08 24. " VS_SHORT_ERR ,Vsync Short Error" "No error,Error" textline " " bitfld.long 0x08 16. " VS_ERR ,Vsync Error(disconnected)" "No error,Error" bitfld.long 0x08 9. " HS_LONG_ERR ,Hsync Long Error" "No error,Error" textline " " bitfld.long 0x08 8. " HS_SHORT_ERR ,Hsync Short Error" "No error,Error" bitfld.long 0x08 0. " HS_ERR ,Hsync Error(disconnected)" "No error,Error" line.long 0x0C "SYNC_ERR_MSK,Synchronisation Error Mask register" bitfld.long 0x0C 25. " MSK_VS_LONG_ERR ,Mask Vsync Long Error" "Enabled,Disabled" bitfld.long 0x0C 24. " MSK_VS_SHORT_ERR ,Mask Vsync Short Error" "Enabled,Disabled" textline " " bitfld.long 0x0C 16. " MSK_VS_ERR ,Mask Vsync Error" "Enabled,Disabled" bitfld.long 0x0C 9. " MSK_HS_LONG_ERR ,Mask Hsync Long Error" "Enabled,Disabled" textline " " bitfld.long 0x0C 8. " MSK_HS_SHORT_ERR ,Mask Hsync Short Error" "Enabled,Disabled" bitfld.long 0x0C 0. " MSK_HS_ERR ,Mask Hsync Error" "Enabled,Disabled" rgroup.long 0x88++0x03 line.long 0x00 "CVCNT,Capture Vertical Count register" hexmask.long.word 0x00 0.--11. 1. " CVCNT ,Capture Vertical Count" group.long 0x98++0x07 line.long 0x00 "CDCN,Capture Data Count (NTSC) register" hexmask.long.word 0x00 16.--28. 1. " BDCN ,Blanking Data Count (NTSC)" hexmask.long.word 0x00 0.--13. 1. " VDCN ,Valid Data Count (NTSC)" line.long 0x04 "CDCP,Capture Data Count (PAL) register" hexmask.long.word 0x04 16.--28. 1. " BDCP ,Blanking Data Count (PAL)" hexmask.long.word 0x04 0.--13. 1. " VDCP ,Valid Data Count (PAL)" group.long 0xA8++0x0B line.long 0x00 "MDS,Mode select register" bitfld.long 0x00 4.--5. " VCMIM ,YC Multiplex video input mode" "RGB input mode,,,YC Multiplex input mode" line.long 0x04 "CDCNS,Capture Data Count (NTSC Short)" hexmask.long.word 0x04 16.--28. 1. " BDCN_S ,Blanking Data Count (NTSC Short)" hexmask.long.word 0x04 0.--13. 1. " VDCN_S ,Valid Data Count (NTSC Short)" line.long 0x08 "CDCPS,Capture Data Count (PAL Short)" hexmask.long.word 0x08 16.--28. 1. " BDCP_S ,Blanking Data Count (PAL Short)" hexmask.long.word 0x08 0.--13. 1. " VDCP_S ,Valid Data Count (PAL Short)" rgroup.long 0xCC++0x03 line.long 0x00 "VINLC_KEP,Video Input Line Count" hexmask.long.word 0x00 0.--12. 1. " VIN_LINE_NO_KEP ,Line count of one frame (field) including the blanking period" group.long 0xD4++0x0F line.long 0x00 "VHSLS,Video Input HSYNC Long/Short register" hexmask.long.word 0x00 16.--29. 1. " VIN_HS_LONG ,Sets the video input long interval HSYNC monitoring" hexmask.long.word 0x00 0.--13. 1. " VIN_HS_SHORT ,Configures the video input short interval HSYNC monitoring" line.long 0x04 "VHSDC,Video HSYNC Down Count register" bitfld.long 0x04 31. " VIN_EHSYNC_MSK ,Video Input Error HSYNC Mask" "Disabled,Enabled" hexmask.long.byte 0x04 0.--7. 1. " VIN_HDOWN_CNT ,Configures the video input HSYNC disconnected monitoring cycle" line.long 0x08 "VVSLS,Video Input VSYNC Long/Short register" hexmask.long.word 0x08 16.--28. 1. " VIN_VS_LONG ,Sets video input long interval VSYNC monitoring" hexmask.long.word 0x08 0.--12. 1. " VIN_VS_SHORT ,Configures the video input short interval VSYNC monitoring" if (((per.l(ad:0xD0860000+0xA8))&0x30)==0x30) group.long 0xE0++0x03 line.long 0x00 "VVSDC,Video Input VSYNC Down Count register" bitfld.long 0x00 31. " VIN_EVSYNC_MSK ,Video Input Error VSYNC Mask" "0,1" hexmask.long.byte 0x00 0.--7. 1. " VIN_VDOWN_CNT ,Configures the video input VSYNC disconnected monitoring cycle" else group.long 0xE0++0x03 line.long 0x00 "VVSDC,Video Input VSYNC Down Count register" hexmask.long.byte 0x00 0.--7. 1. " VIN_VDOWN_CNT ,Configures the video input VSYNC disconnected monitoring cycle" endif group.long 0x108++0x27 line.long 0x00 "SDER,Still Detection Enable Register" hexmask.long.word 0x00 16.--26. 1. " SDMOPIX ,The number of pixels of the reduced frame n which were detected as motion pixels" rbitfld.long 0x00 3. " BF ,Bottom Field" "Top,Bottom" textline " " rbitfld.long 0x00 2. " SDMON ,Still Detection Monitor" "Interpolation,Non-interpolation" bitfld.long 0x00 1. " SDMAN ,Still Detection Manual Mode" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " SDEN ,Still Detection Enable" "Disabled,Enabled" line.long 0x04 "SDCF0,Still Detection Config register 0" hexmask.long.word 0x04 16.--24. 1. " MLC ,Maximum Line Count" hexmask.long.word 0x04 0.--10. 1. " MPC ,Maximum Pixel Count" line.long 0x08 "SDCF1,Still Detection Config register 1" hexmask.long.word 0x08 16.--26. 1. " MB ,Motion Blocks" hexmask.long.word 0x08 0.--10. 1. " MA ,The Maximum Address (MA) of reduced frame memory" line.long 0x0C "SDTH,Still Detection Threshold register" hexmask.long.tbyte 0x0C 0.--16. 1. " CBTH ,Compare Blocks Threshold value" line.long 0x10 "SDHY,Still Detection Hysteresis register" bitfld.long 0x10 24.--29. " SLB ,Still Look Back" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x10 16.--21. " MLB ,Motion Look Back" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x10 8.--13. " MO2ST ,Motion to Still switch value" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x10 0.--5. " ST2MO ,Still to Motion switch value" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x14 "HDCFG,High Definition (HD) Configuration Register" bitfld.long 0x14 5. " HD_EN_TO_DET ,Enable timeout detection" "Disabled,Enabled" bitfld.long 0x14 4. " HD_EN_ERR_DET ,Enable error detection" "Disabled,Enabled" textline " " bitfld.long 0x14 2.--3. " HD_SPREAD ,HD spread" "All AV tags are on the Y,All AV tags are on the CbCr,Alternating CbCr component,Alternating Y component" bitfld.long 0x14 1. " HD_SWAP ,HD swap" "No swap,Swap" textline " " bitfld.long 0x14 0. " HD_RUN ,HD run" "Disabled,Enabled" line.long 0x18 "HDEST,High definition Error Status Register" bitfld.long 0x18 5. " HD_L_ERR_NOL ,Long Error in Number of active lines detected" "No error,Error" bitfld.long 0x18 4. " HD_L_ERR_HACT ,Long Error in HACTIVE detected" "No error,Error" textline " " bitfld.long 0x18 3. " HD_L_ERR_HBL ,Long Error in HBLANK detected" "No error,Error" bitfld.long 0x18 2. " HD_S_ERR_NOL ,Short Error in Number of active lines detected" "No error,Error" textline " " bitfld.long 0x18 1. " HD_S_ERR_HACT ,Short Error in HACTIVE detected" "No error,Error" bitfld.long 0x18 0. " HD_S_ERR_HBL ,Short Error in HBLANK detected" "No error,Error" line.long 0x1C "HDMSK,High definition Error Mask register" bitfld.long 0x1C 5. " MSK_HD_L_ERR_NOL ,Mask register for HD_L_ERR_NOL" "Disabled,Enabled" bitfld.long 0x1C 4. " MSK_HD_L_ERR_HACT ,Mask register for HD_L_ERR_HACT" "Disabled,Enabled" textline " " bitfld.long 0x1C 3. " MSK_HD_L_ERR_HBL ,Mask register for HD_L_ERR_HBL" "Disabled,Enabled" bitfld.long 0x1C 2. " MSK_HD_S_ERR_NOL ,Mask register for HD_S_ERR_NOL" "Disabled,Enabled" textline " " bitfld.long 0x1C 1. " MSK_HD_S_ERR_HACT ,Mask register for HD_S_ERR_HACT" "Disabled,Enabled" bitfld.long 0x1C 0. " MSK_HD_S_ERR_HBL ,Mask register for HD_S_ERR_HBL" "Disabled,Enabled" line.long 0x20 "HDHBL,High definition HBLANK error detection parameter register" hexmask.long.word 0x20 16.--26. 1. " HD_L_HBL ,HBLANK long parameter to compare with. Error if frame HBLANK is larger than this value" hexmask.long.word 0x20 0.--10. 1. " HD_S_HBL ,HBLANK short parameter to compare with.Error if frame HBLANK is smaller than this value" line.long 0x24 "HDHACT,High definition HACTIVE error detection parameter register" hexmask.long.word 0x24 16.--24. 1. " HD_L_HACT ,HACTIVE long parameter to compare with Error if frame HACTIVE is larger than this value" hexmask.long.word 0x24 0.--10. 1. " HD_S_HACT ,HACTIVE short parameter to compare with Error if frame HACTIVE is smaller than this value" group.long 0x130++0x27 line.long 0x00 "HDNOL,High definition NOL (number of lines) error detection parameter register" hexmask.long.word 0x00 16.--26. 1. " HD_L_NOL ,Number of active lines long parameter" hexmask.long.word 0x00 0.--10. 1. " HD_S_NOL ,Number of active lines short parameter" line.long 0x04 "CM_COEFF_0,Color Matrix Coefficient Register 0" hexmask.long.word 0x04 0.--10. 1. " CMKY ,Coefficient for Y, same for R,G,B calculation" line.long 0x08 "CM_COEFF_1,Color Matrix Coefficient Register 1" hexmask.long.word 0x08 16.--26. 1. " CMKCBB ,Coefficient for Cb, for calculation of B value" hexmask.long.word 0x08 0.--10. 1. " CMKCBG ,Coefficient for Cb, for calculation of G value" line.long 0x0C "CM_COEFF_2,Color Matrix Coefficient Register 2" hexmask.long.word 0x0C 16.--26. 1. " CMKCRG ,Coefficient for Cr, for calculation of G value" hexmask.long.word 0x0C 0.--10. 1. " CMKCRR ,Coefficient for Cr, for calculation of R value" line.long 0x10 "SWRSTREG,Software Reset Register" bitfld.long 0x10 0. " SWRST ,Software Reset" "No reset,Reset" line.long 0x14 "WRBUFFERERROR,Write Buffer Error" eventfld.long 0x14 0. " WRBE ,Error Status" "Normal,Error" line.long 0x18 "WRBUFERRIE,Write Buffer Error Interrupt Enable" bitfld.long 0x18 0. " WRBEIE ,Enable to generate interrupt singal of buffer error. Emerald-L(MP) only" "Disabled,Enbaled" line.long 0x1C "D_YHLPF,Direct coefficient for Y component Horizontal LPF" bitfld.long 0x1C 24.--29. " K4YH ,K4 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x1C 18.--23. " K3YH ,K3 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x1C 12.--17. " K2YH ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x1C 6.--11. " K1YH ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x1C 0.--5. " K0YH ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x20 "D_CHLPF,Direct coefficient for C component Horizontal LPF" bitfld.long 0x20 24.--29. " K4CH ,K4 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x20 18.--23. " K3CH ,K3 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x20 12.--17. " K2CH ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x20 6.--11. " K1CH ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x20 0.--5. " K0CH ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x24 "D_VLPF,Direct coefficient for vertical LPF" bitfld.long 0x24 26.--30. " K2CV ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x24 21.--25. " K1CV ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x24 16.--20. " K0CV ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x24 10.--14. " K2YV ,K2 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x24 5.--9. " K1YV ,K1 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x24 0.--4. " K0YV ,K0 coefficient of LPF" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x380++0x03 line.long 0x00 "CBM1,Capture Buffer Mode 1" sif (cpu()=="MB86R12") bitfld.long 0x00 20. " YRGB ,Enable YRGB format, only valid if 32bpp is used" "Disabled,Enabled" textline " " endif bitfld.long 0x00 16. " WMODE ,Weave mode" "Disabled,Enabled" bitfld.long 0x00 2. " IDMAXH ,ID max hold" "From 255 to 0,Stops at 255" textline " " bitfld.long 0x00 1. " IDRESM ,ID reset mode" "No reset,Reset" bitfld.long 0x00 0. " IDRDS ,ID read select" "Read now,Read recently" rgroup.long 0x384++0x03 line.long 0x00 "CBSTA,Capture Buffer Status" bitfld.long 0x00 16. " VALID ,Valid" "No effective,Effective" hexmask.long.byte 0x00 0.--7. 1. " IDCNT ,ID count" group.long 0x388++0x03 line.long 0x00 "CBA2,Capture Buffer Address 2" hexmask.long 0x00 4.--31. 0x10 " CBA2 ,The first address in a new area when the swap of the capture buffer is executed is set" rgroup.long 0x38C++0x03 line.long 0x00 "CBA3,Capture Buffer Address 3" group.long 0x390++0x07 line.long 0x00 "CBSWS,Capture Buffer Swap Select" bitfld.long 0x00 3. " CBSWS3 ,Capture buffer swap select 3" "Not selected,Selected" bitfld.long 0x00 2. " CBSWS2 ,Capture buffer swap select 2" "Not selected,Selected" textline " " bitfld.long 0x00 2. " CBSWS1 ,Capture buffer swap select 1" "Not selected,Selected" bitfld.long 0x00 0. " CBSWS0 ,Capture buffer swap select 0" "Not selected,Selected" line.long 0x04 "CBSWP,Capture Buffer Swap" width 0xb tree.end sif (cpu()=="MB86R11F") tree "GDC Controller" base ad:0x3C300000 width 18. group.long 0x00++0x03 line.long 0x00 "Control_Register,Control Register 1" bitfld.long 0x00 16. " RTD ,RgbYuv Display size" "720pixel,640pixel" group.long 0x10++0x03 line.long 0x00 "Control2_Register,Control2 Register 2" bitfld.long 0x00 2. " YCS ,YCbcr dfference Select" "Not optimal,Optimal" bitfld.long 0x00 1. " BLS ,Blank period select" "Gray,Black" textline " " bitfld.long 0x00 0. " DCK1S ,It is selected whether to invert the Pixel clock generated at Display1" "Not inverted,Inverted" width 0xb tree.end endif tree "3D Graphic Engine" base ad:0xD1000000 tree "DDLFIFO" width 10. hgroup.long 0x0++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x4++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x8++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0xC++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x10++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x14++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x18++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x1C++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x20++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x24++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x28++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x2C++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x30++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x34++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x38++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x3C++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x40++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x44++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x48++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x4C++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x50++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x54++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x58++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x5C++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x60++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x64++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x68++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x6C++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x70++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x74++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x78++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in hgroup.long 0x7C++0x03 hide.long 0x00 " DDLFIFO ,Direct Display List FIFO" in tree.end width 16. rgroup.long 0x100++0x03 line.long 0x00 "STATUS,Indicates status of the 3D Graphic Engine" hexmask.long.byte 0x00 15.--22. 1. " FCNT ,FIFO Counter" bitfld.long 0x00 14. " NF ,Near Full" "Greater than 64,Less than 64" textline " " bitfld.long 0x00 13. " FF ,FIFO Full" "Not full,Full" bitfld.long 0x00 12. " FE ,FIFO Empty" "Not empty,Empty" textline " " bitfld.long 0x00 1. " BFST ,Buffer Status" "Empty,Pixel in buffer" bitfld.long 0x00 0. " ST ,Status" "Idle,Busy" group.long 0x104++0x17 line.long 0x00 "SRESET,Do software reset to 3D Graphic Engine" bitfld.long 0x00 0. " SRST ,Soft Reset" "No reset,Reset" line.long 0x04 "CMDINT,Command Interpreter's Normal Interrupt Information" eventfld.long 0x04 1. " DFIN ,Drawing Finished interrupt" "Not occurred,Occurred" eventfld.long 0x04 0. " FIFO ,Interrupt DL command read from display list FIFO" "Not detected,Detected" line.long 0x08 "CMDINTM,Mask of Command Interpreter's Normal Interrupt" bitfld.long 0x08 1. " MDFIN ,Mask of interrupt of Drawing Finished" "Not masked,Masked" bitfld.long 0x08 0. " MFIFO ,Masks interrupt during DL interpretation" "Not masked,Masked" line.long 0x0C "CMDERR,Command Interpreter's Abnormal Interrupt Information" bitfld.long 0x0C 16. " AXIER ,Interrupt of AXI protocol error" "Not occurred,Occurred" bitfld.long 0x0C 0. " CERR ,Interrupt of Command Error" "Not detected,Detected" line.long 0x10 "CMDERRM,Mask of Command Interpreter's Abnormal Interrupt" bitfld.long 0x10 16. " MAXIER ,Mask of AXI protocol error interrupt" "Not masked,Masked" bitfld.long 0x10 0. " MCERR ,Mask of Command Error interrupt" "Not masked,Masked" textline " " line.long 0x14 "CMDINTR,Command Interpreter's Normal Interrupt" eventfld.long 0x14 31. " F_[31] ,31 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 30. " [30] ,30 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 29. " [29] ,29 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 28. " [28] ,28 interrupt status" "Not occurred,Occurred" textline " " eventfld.long 0x14 27. " [27] ,27 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 26. " [26] ,26 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 25. " [25] ,25 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 24. " [24] ,24 interrupt status" "Not occurred,Occurred" textline " " eventfld.long 0x14 23. " [23] ,23 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 22. " [22] ,22 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 21. " [21] ,21 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 20. " [20] ,20 interrupt status" "Not occurred,Occurred" textline " " eventfld.long 0x14 19. " [19] ,19 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 18. " [18] ,18 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 17. " [17] ,17 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 16. " [16] ,16 interrupt status" "Not occurred,Occurred" textline " " eventfld.long 0x14 15. " [15] ,15 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 14. " [14] ,14 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 13. " [13] ,13 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 12. " [12] ,12 interrupt status" "Not occurred,Occurred" textline " " eventfld.long 0x14 11. " [11] ,11 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 10. " [10] ,10 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 9. " [9] ,9 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 8. " [8] ,8 interrupt status" "Not occurred,Occurred" textline " " eventfld.long 0x14 7. " [7] ,7 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 6. " [6] ,6 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 5. " [5] ,5 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 4. " [4] ,4 interrupt status" "Not occurred,Occurred" textline " " eventfld.long 0x14 3. " [3] ,3 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 2. " [2] ,2 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 1. " [1] ,1 interrupt status" "Not occurred,Occurred" eventfld.long 0x14 0. " [0] ,0 interrupt status" "Not occurred,Occurred" textline " " rgroup.long 0x11C++0x03 line.long 0x00 "MID,ID for identifying 3D Graphic Engine macro" hexmask.long.byte 0x00 8.--15. 1. " MN ,Macro Name" hexmask.long.byte 0x00 0.--7. 1. " VER ,Version" rgroup.long 0x300++0x07 line.long 0x00 "ERRORDL,Error Cause Display List Command" line.long 0x04 "DL_CNT,Display List Command Counter" group.long 0x308++0x03 line.long 0x00 "ENDCHG,Endian Change" bitfld.long 0x00 2.--3. " RGED ,Register access Endian Definition" "Little endian 32bits,,Little endian,Big endian" bitfld.long 0x00 0.--1. " FIED ,FIFO Endian Definition" "Little endian of 32bits,,Little endian,Big endian" group.long 0x528++0x03 line.long 0x00 "DBGMODE,Debug Mode" bitfld.long 0x00 0. " DBG ,Debug mode enable" "Normal,Debug" if (((per.l(ad:0xD1000000+0x528))&0x01)==0x01) group.long 0x20038++0x07 line.long 0x00 "DepthPassCount,number of pixels that have passed a depth test between SetQuery:Begin and SetQuery:End" line.long 0x04 "DepthFailCount,number of pixels that have failed a depth test between SetQuery:Begin and SetQuery:End" else hgroup.long 0x20038++0x07 hide.long 0x00 "DepthPassCount,number of pixels that have passed a depth test between SetQuery:Begin and SetQuery:End" hide.long 0x04 "DepthFailCount,number of pixels that have failed a depth test between SetQuery:Begin and SetQuery:End" endif width 0xb tree.end tree "Shader" base ad:0xD1040000 width 9. group.long 0x00++0x13 line.long 0x00 "SHDSTAT,Shader status" bitfld.long 0x00 31. " SHDBUSY ,Execution unit is busy" "0,1" textline " " sif (cpu()=="MB86R12") eventfld.long 0x00 7. " FPUINFPIX ,At least one pixblt shader operation resulted in plus or minus infinite" "0,1" eventfld.long 0x00 6. " FPUNANPIX ,At least one pixblt shader operation resulted undefined" "0,1" textline " " endif eventfld.long 0x00 5. " FPUINFFRG ,At least one fragment shader operation resulted in plus or minus infinite" "0,1" eventfld.long 0x00 4. " FPUNANFRG ,At least one fragment shader operation resulted undefined" "0,1" textline " " eventfld.long 0x00 3. " FPUINFVTX ,At least one vertex shader operation resulted in plus or minus infinite" "0,1" eventfld.long 0x00 2. " FPUNANVTX ,At least one vertex shader operation resulted undefined" "0,1" textline " " eventfld.long 0x00 1. " EXUBADCODE ,Execution unit has processed an invalid instruction code" "0,1" eventfld.long 0x00 0. " SHDINIT ,Software reset" "No reset,Reset" line.long 0x04 "SHDCTRL,Shader control settings" bitfld.long 0x04 8.--12. " NUMVTX ,Number of vertex shader output temporary registers" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x04 5.--7. " PERFPERIOD ,Defines the measurement period for performance counters" "16 clock cycles,16^2 clock cycles,16^3 clock cycles,16^4 clock cycles,16^5 clock cycles,16^6 clock cycles,16^7 clock cycles,16^8 clock cycles" textline " " bitfld.long 0x04 3.--4. " CTXBITSBND ,Set context bundle number" "Defined by ctxBits,2 times more,4 times more,8 times more" bitfld.long 0x04 0.--2. " CTXBITS ,Set context number" "128 registers,64 registers,32 registers,16 registers,8 registers,4 registers,," line.long 0x08 "FRGCTR,Control settings for fragment shaders" bitfld.long 0x08 26.--31. " ARBCTXFRG ,Controls dynamic load balancing" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x08 25. " BNDCTXFRG ,Enable increased number of temporary registers for fragment shaders" "Enabled,Disabled" bitfld.long 0x08 23.--24. " AUTOKICKFRG ,Mode for automatic kick of shader execution" "No auto kick,Auto kick 5 clock cycles,Auto kick 25 clock cycles,Auto kick 125 clock cycles" textline " " bitfld.long 0x08 21.--22. " ARBMODEFRG ,Load balancing mode for fragment shaders" "Always,Not idle,Not idle and stalled,Smaller than perfCntFrg" bitfld.long 0x08 20. " TEXFORMATFRG ,Controls texel color conversion from 4 x Uint8 to 4 x Fp16 normalized for fragment shader input" "Enabled,Disabled" bitfld.long 0x08 19. " FRGFORMAT ,Controls fragment shader output data conversion from 4 x Fp16 normalized to 4 x Uint8 color codes" "Enabled,Disabled" textline " " hexmask.long.word 0x08 10.--18. 1. " UNIOFSFRG ,Offset for uniform register addressing" hexmask.long.word 0x08 0.--9. 1. " EXUADRFRG ,Start address of shader program" line.long 0x0C "FRGOFS,Temporary register indices for fragment shaders" hexmask.long.byte 0x0C 24.--30. 1. " TEXOFSFRG ,Index of texel color" hexmask.long.byte 0x0C 16.--22. 1. " CRDOFSFRG ,Index of texel coordinates" textline " " hexmask.long.byte 0x0C 8.--14. 1. " COLOFSFRG ,Index of the output fragment color" hexmask.long.byte 0x0C 0.--6. 1. " DISOFSFRG ,Index of the first input varying variable" line.long 0x10 "VTXCTR,Control settings for vertex shaders" bitfld.long 0x10 26.--31. " ARBCTXVTX ,Controls dynamic load balancing" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x10 25. " BNDCTXVTX ,Enable increased number of temporary registers for vertex shaders" "Enabled,Disabled" bitfld.long 0x10 23.--24. " AUTOKICKVTX ,Mode for automatic kick of shader execution" "No auto kick,Auto kick 10 clock cycles,Auto kick 100 clock cycles,Auto kick 1000 clock cycles" textline " " bitfld.long 0x10 21.--22. " ARBMODEVTX ,Load balancing mode for fragment shaders" "Always,Not idle,Not idle and stalled," bitfld.long 0x10 20. " TEXFORMATVTX ,Controls texel color conversion from 4 x Uint8 to 4 x Fp16 normalized for vertex shader input" "Enabled,Disabled" hexmask.long.word 0x10 10.--18. 1. " UNIOFSVTX ,Offset for uniform register addressing" textline " " hexmask.long.word 0x10 0.--9. 1. " EXUADRVTX ,Start address of shader program" sif (cpu()=="MB86R12") group.long 0x14++0x13 line.long 0x00 "VTXOFS,Temporary register indices for pixblt shaders" hexmask.long.byte 0x00 24.--30. 1. " TEXOFSVTX ,Index of texel color" hexmask.long.byte 0x00 16.--22. 1. " CRDOFSVTX ,Index of texel coordinates" textline " " hexmask.long.byte 0x00 8.--14. 1. " COLOFSVTX ,Index of the first output varying variable" hexmask.long.byte 0x00 0.--6. 1. " DISOFSVTX ,Index of the first input attribute" line.long 0x04 "PIXCTR,Control settings for pixblt shaders" bitfld.long 0x04 26.--31. " ARBCTXPIX ,Controls dynamic load balancing" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x04 25. " BNDCTXPIX ,Enable increased number of temporary registers for vertex shaders" "Enabled,Disabled" bitfld.long 0x04 21.--22. " ARBMODEPIX ,Load balancing mode for fragment shaders" "Always,Not idle,Not idle and stalled," textline " " bitfld.long 0x04 20. " TEXFORMATPIX ,Controls texel color conversion from 4 x Uint8 to 4 x Fp16 normalized for vertex shader input" "Enabled,Disabled" bitfld.long 0x04 19. " PIXFORMAT ,Data format of the 32-bit word that is received from and sent to the PixBlt unit" "4x Uint8,2x Fp16/1x Fp32" hexmask.long.word 0x04 10.--18. 1. " UNIOFSPIX ,Offset for uniform register addressing" textline " " hexmask.long.word 0x04 0.--9. 1. " EXUADRPIX ,Start address of shader program" line.long 0x08 "PIXOFS,Temporary register indices for pixblt shaders" hexmask.long.byte 0x08 24.--30. 1. " TEXOFSPIX ,Index of texel color" hexmask.long.byte 0x08 16.--22. 1. " CRDOFSPIX ,Index of texel coordinates" textline " " hexmask.long.byte 0x08 8.--14. 1. " COLOFSPIX ,Index of the first output varying variable" hexmask.long.byte 0x08 0.--6. 1. " DISOFSPIX ,Index of the first input attribute" line.long 0x0C "DBGCTRL,Debugging support features" bitfld.long 0x0C 3.--4. " DUMPCNT ,Replaces the output of fragment shaders by the current value of certain status registers" "No replacement,PerfCnt register,TypeCnt register," endif rgroup.long 0x24++0x07 line.long 0x00 "PERFCNT,Counters for shader load analysis" sif (cpu()=="MB86R12") bitfld.long 0x00 28.--31. " PERFCNTBLT ,PixBlt shader output interface" "No load,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Full load" textline " " endif bitfld.long 0x00 24.--27. " PERFCNTGEO ,Vertex shader output interface" "No load,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Full load" bitfld.long 0x00 20.--23. " PERFCNTROP ,Fragment shader output interface" "No load,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Full load" textline " " bitfld.long 0x00 16.--19. " PERFCNTTEX ,Texture unit" "No load,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Full load" bitfld.long 0x00 12.--15. " PERFCNTFPU ,Floating-Point units" "No load,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Full load" textline " " sif (cpu()=="MB86R12") bitfld.long 0x00 8.--11. " PERFCNTPIX ,PixBlt shader input interface" "No load,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Full load" textline " " endif bitfld.long 0x00 4.--7. " PERFCNTVTX ,Vertex shader input interface" "No load,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Full load" bitfld.long 0x00 0.--3. " PERFCNTFRG ,Fragment shader input interface" "No load,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Full load" line.long 0x04 "TYPECNT,Counters for shader type allocation analysis" sif (cpu()=="MB86R12") bitfld.long 0x04 16.--20. " TYPECNTPIX ,Number of bundles allocated for pixblt shaders" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " endif bitfld.long 0x04 8.--12. " TYPECNTVTX ,Number of bundles allocated for vertex shaders" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x04 0.--4. " TYPECNTFRG ,Number of bundles allocated for fragment shaders" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" width 0xb tree.end tree "Pixel Engine" base ad:0x38C00000 width 24. tree "Fetch 0" group.long 0x00++0xF line.long 0x00 "BURSTBUFFERMANAGEMENT,AXI interface buffer management register" bitfld.long 0x00 24.--28. " SETBURSTLENGTH ,Set this to the burst length that should be used on the AXI interface" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.byte 0x00 16.--23. 1. " SETNUMBUFFERS ,Set this to the number of bursts that should be buffered" textline " " rbitfld.long 0x00 8.--12. " BURSTLENGTHFORMAXBUFFERS ,Maximum Burst Length that can be used when ManagedBurstBuffers burst buffers are used" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.byte 0x00 0.--7. 1. " MANAGEDBURSTBUFFERS ,Maximum number of burst buffers that can be administrated in the AXI interface" line.long 0x04 "BASEADDRESS,Source buffer base address" line.long 0x08 "SOURCEBUFFERSTRIDE,Source buffer stride" hexmask.long.word 0x08 0.--13. 1. " STRIDE ,Source buffer stride in bytes minus one used for address generation" line.long 0x0C "SOURCEBUFFERATTRIBUTES,Source buffer attributes" hexmask.long.word 0x0C 16.--27. 1. " LINECOUNT ,Number of lines of the source buffer minus one needed for tiling" hexmask.long.word 0x0C 0.--11. 1. " LINEWIDTH ,Width of the source buffer in pixels minus one needed for tiling" if (((per.l(ad:0x38C00000+0x44))&0x30000000)==0x10000000) group.long 0x10++0x03 line.long 0x00 "SOURCEBUFFERLENGTH,Source Buffer Length for Run Length Decoding" hexmask.long 0x00 0.--24. 1. " RLEWORDS ,Number of 32-bit words minus one that are required to decode the run length encoded source buffer" else hgroup.long 0x10++0x03 hide.long 0x00 "SOURCEBUFFERLENGTH,Source Buffer Length for Run Length Decoding" endif group.long 0x14++0x07 line.long 0x00 "FRAMEXOFFSET,Frame X offset" hexmask.long.word 0x00 16.--29. 1. " FRAMEXOFFSET ,Frame X origin offset relative to the source buffer origin" line.long 0x04 "FRAMEYOFFSET,Frame Y offset" hexmask.long.word 0x04 16.--29. 1. " FRAMEYOFFSET ,Frame Y origin offset relative to the source buffer origin" if (((per.l(ad:0x38C00000+0x44))&0x30000000)==0x20000000) group.long 0x1C++0x03 line.long 0x00 "FRAMEDIMENSIONS,Defines frame rectangle" hexmask.long.word 0x00 16.--27. 1. " FRAMEHEIGHT ,Frame height minus one" hexmask.long.word 0x00 0.--11. 1. " FRAMEWIDTH ,Frame width minus one" hgroup.long 0x20++0x07 hide.long 0x00 "DELTAXX,DeltaXX stepsize" hide.long 0x04 "DELTAYY,DeltaYY stepsize" else group.long 0x1C++0x03 line.long 0x00 "FRAMEDIMENSIONS,Defines frame rectangle" bitfld.long 0x00 31. " FRAMESWAPDIRECTIONS ,Swaps X and Y directions" "0,1" hexmask.long.word 0x00 16.--27. 1. " FRAMEHEIGHT ,Frame height minus one" textline " " hexmask.long.word 0x00 0.--11. 1. " FRAMEWIDTH ,Frame width minus one" group.long 0x20++0x07 line.long 0x00 "DELTAXX,DeltaXX stepsize" bitfld.long 0x00 14.--19. " DELTAX ,DeltaX stepsize for repetition operation given in signed fixed-point 4.2 two's complement notation" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x04 "DELTAYY,DeltaYY stepsize" bitfld.long 0x04 14.--19. " DELTAY ,DeltaY stepsize for repetition operation given in signed fixed-point 4.2 two's complement notation" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" endif group.long 0x30++0x13 line.long 0x00 "SKIPWINDOWOFFSET,Skip window offset" hexmask.long.word 0x00 16.--27. 1. " SKIPWINDOWYOFFSET ,Skip window Y offset relative to the source buffer origin" hexmask.long.word 0x00 0.--11. 1. " SKIPWINDOWXOFFSET ,Skip window X offset relative to the source buffer origin" line.long 0x04 "SKIPWINDOWDIMENSIONS,Defines skip window rectangle" hexmask.long.word 0x04 16.--27. 1. " SKIPWINDOWHEIGHT ,Skip window height" hexmask.long.word 0x04 0.--11. 1. " SKIPWINDOWWIDTH ,Skip window width" line.long 0x08 "COLORCOMPONENTBITS,Color component size of source buffer" bitfld.long 0x08 24.--27. " COMPONENTBITSRED ,ComponentBitsRed" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x08 16.--19. " COMPONENTBITSGREEN ,ComponentBitsGreen" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x08 8.--11. " COMPONENTBITSBLUE ,ComponentBitsBlue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x08 0.--3. " COMPONENTBITSALPHA ,ComponentBitsAlpha" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x0C "COLORCOMPONENTSHIFT,Color component offset of source buffer" bitfld.long 0x0C 24.--28. " COMPONENTSHIFTRED ,ComponentShiftRed" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0C 16.--20. " COMPONENTSHIFTGREEN ,ComponentShiftGreen" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0C 8.--12. " COMPONENTSHIFTBLUE ,ComponentShiftBlue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0C 0.--4. " COMPONENTSHIFTALPHA ,ComponentShiftAlpha" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x10 "CONSTANTCOLOR,Constant color settings" hexmask.long.byte 0x10 24.--31. 1. " CONSTANTCOLORRED ,ConstantColorRed" hexmask.long.byte 0x10 16.--23. 1. " CONSTANTCOLORGREEN ,ConstantColorGreen" textline " " hexmask.long.byte 0x10 8.--15. 1. " CONSTANTCOLORBLUE ,ConstantColorBlue" hexmask.long.byte 0x10 0.--7. 1. " CONSTANTCOLORALPHA ,ConstantColorAlpha" if ((((per.l(ad:0x38C00000+0x44))&0x30000000)==0x10000000)&&(((per.l(ad:0x38C00000+0x44))&0x40000000)==0x00000000)) group.long 0x44++0x03 line.long 0x00 "CONTROL,Fetch unit main control register" bitfld.long 0x00 31. " SHD_UPD ,Overrides the standard shadow load mechanisms and constantly loads shadows" "Normal,Update" rbitfld.long 0x00 30. " HASMULTIPLY ,This field can be used to determine if this fetch can perform color multiplications" "MULTIPLY,NO_MULTIPLY" textline " " rbitfld.long 0x00 28.--29. " FETCHTYPE ,This field can be used to determine what kind of fetch unit this is" "SIMPLE,RLD,ROT," bitfld.long 0x00 24. " RLDENABLE ,Enables use of the Run Length Decompression feature" "Enabled,Disabled" textline " " bitfld.long 0x00 23. " RLDCMDCOMP ,Enables use of the Command Compatibility Mode with the Run Length Decompression feature" "Disabled,Enabled" bitfld.long 0x00 21.--22. " TILEMODE ,Select the tile mode for pixels outside the source buffer" "TILE_PAD,TILE_FILL_CONSTANT,TILE_FILL_ZERO," textline " " bitfld.long 0x00 20. " DUMMYSKIPSELECT ,Select which values to use for skipped pixels inside the skip rectangle" "CONSTANTCOLOR,ZERO" bitfld.long 0x00 17. " TOGGLEFIELD ,Enable toggling of the field bit of the command word output to the pixel pipeline between frames" "Disabled,Enabled" textline " " bitfld.long 0x00 16. " SETFIELD ,The fld control bit of the start of frame control word of the pixel pipeline" "0,1" bitfld.long 0x00 14. " COLORMULTIPLYSELECT ,Select which multiplicator to use for color multiply" "ALPHA,CONSTANTCOLOR" textline " " bitfld.long 0x00 13. " COLORMULTIPLYENABLE ,Enable multiplication of color values after constant alpha multiplication stage" "Disabled,Enabled" bitfld.long 0x00 12. " ALPHAMULTIPLY ,Enable multiplication of pixel alpha withconstant alpha" "Disabled,Enabled" textline " " bitfld.long 0x00 10.--11. " ENDIANSWAP ,Configure the endian swap on the 64 bit word" "Disabled,Word_16bit,Word_32bit,Word_64bit" bitfld.long 0x00 4.--9. " BITSPERPIXEL ,Pixel size in bits has to be a power of two or 24" "-,TOTALBITS_1,TOTALBITS_2,-,TOTALBITS_4,-,-,-,TOTALBITS_8,-,-,-,-,-,-,-,TOTALBITS_16,-,-,-,-,-,-,-,TOTALBITS_24,-,-,-,-,-,-,-,TOTALBITS_32,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-" textline " " bitfld.long 0x00 3. " CLOCKDISABLE ,Deactivates most internal clocks of fetch unit" "OPERATION,POWERDOWN" bitfld.long 0x00 2. " SWRESET ,Puts the fetch unit in software reset" "OPERATION,SW_RESET" textline " " bitfld.long 0x00 1. " START ,Writing a '1' starts processing" "Stopped,Started" bitfld.long 0x00 0. " SHADOWLOAD ,Set this to '1' if you want the fetch unit to perform a shadow load with the next start of operation" "0,1" elif ((((per.l(ad:0x38C00000+0x44))&0x30000000)!=0x10000000)&&(((per.l(ad:0x38C00000+0x44))&0x40000000)==0x40000000)) group.long 0x44++0x03 line.long 0x00 "CONTROL,Fetch unit main control register" bitfld.long 0x00 31. " SHD_UPD ,Overrides the standard shadow load mechanisms and constantly loads shadows" "Normal,Update" rbitfld.long 0x00 30. " HASMULTIPLY ,This field can be used to determine if this fetch can perform color multiplications" "MULTIPLY,NO_MULTIPLY" textline " " rbitfld.long 0x00 28.--29. " FETCHTYPE ,This field can be used to determine what kind of fetch unit this is" "SIMPLE,RLD,ROT," bitfld.long 0x00 21.--22. " TILEMODE ,Select the tile mode for pixels outside the source buffer" "TILE_PAD,TILE_FILL_CONSTANT,TILE_FILL_ZERO," textline " " bitfld.long 0x00 20. " DUMMYSKIPSELECT ,Select which values to use for skipped pixels inside the skip rectangle" "CONSTANTCOLOR,ZERO" bitfld.long 0x00 17. " TOGGLEFIELD ,Enable toggling of the field bit of the command word output to the pixel pipeline between frames" "Disabled,Enabled" textline " " bitfld.long 0x00 16. " SETFIELD ,The fld control bit of the start of frame control word of the pixel pipeline" "0,1" bitfld.long 0x00 12. " ALPHAMULTIPLY ,Enable multiplication of pixel alpha withconstant alpha" "Disabled,Enabled" textline " " bitfld.long 0x00 4.--9. " BITSPERPIXEL ,Pixel size in bits has to be a power of two or 24" "-,TOTALBITS_1,TOTALBITS_2,-,TOTALBITS_4,-,-,-,TOTALBITS_8,-,-,-,-,-,-,-,TOTALBITS_16,-,-,-,-,-,-,-,TOTALBITS_24,-,-,-,-,-,-,-,TOTALBITS_32,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-" bitfld.long 0x00 3. " CLOCKDISABLE ,Deactivates most internal clocks of fetch unit" "OPERATION,POWERDOWN" textline " " bitfld.long 0x00 2. " SWRESET ,Puts the fetch unit in software reset" "OPERATION,SW_RESET" bitfld.long 0x00 1. " START ,Writing a '1' starts processing" "Stopped,Started" textline " " bitfld.long 0x00 0. " SHADOWLOAD ,Set this to '1' if you want the fetch unit to perform a shadow load with the next start of operation" "0,1" elif ((((per.l(ad:0x38C00000+0x44))&0x30000000)!=0x10000000)&&(((per.l(ad:0x38C00000+0x44))&0x40000000)==0x00000000)) group.long 0x44++0x03 line.long 0x00 "CONTROL,Fetch unit main control register" bitfld.long 0x00 31. " SHD_UPD ,Overrides the standard shadow load mechanisms and constantly loads shadows" "Normal,Update" rbitfld.long 0x00 30. " HASMULTIPLY ,This field can be used to determine if this fetch can perform color multiplications" "MULTIPLY,NO_MULTIPLY" textline " " rbitfld.long 0x00 28.--29. " FETCHTYPE ,This field can be used to determine what kind of fetch unit this is" "SIMPLE,RLD,ROT," bitfld.long 0x00 21.--22. " TILEMODE ,Select the tile mode for pixels outside the source buffer" "TILE_PAD,TILE_FILL_CONSTANT,TILE_FILL_ZERO," textline " " bitfld.long 0x00 20. " DUMMYSKIPSELECT ,Select which values to use for skipped pixels inside the skip rectangle" "CONSTANTCOLOR,ZERO" bitfld.long 0x00 17. " TOGGLEFIELD ,Enable toggling of the field bit of the command word output to the pixel pipeline between frames" "Disabled,Enabled" textline " " bitfld.long 0x00 16. " SETFIELD ,The fld control bit of the start of frame control word of the pixel pipeline" "0,1" bitfld.long 0x00 14. " COLORMULTIPLYSELECT ,Select which multiplicator to use for color multiply" "ALPHA,CONSTANTCOLOR" textline " " bitfld.long 0x00 13. " COLORMULTIPLYENABLE ,Enable multiplication of color values after constant alpha multiplication stage" "Disabled,Enabled" bitfld.long 0x00 12. " ALPHAMULTIPLY ,Enable multiplication of pixel alpha withconstant alpha" "Disabled,Enabled" textline " " bitfld.long 0x00 10.--11. " ENDIANSWAP ,Configure the endian swap on the 64 bit word" "Disabled,Word_16bit,Word_32bit,Word_64bit" bitfld.long 0x00 4.--9. " BITSPERPIXEL ,Pixel size in bits has to be a power of two or 24" "-,TOTALBITS_1,TOTALBITS_2,-,TOTALBITS_4,-,-,-,TOTALBITS_8,-,-,-,-,-,-,-,TOTALBITS_16,-,-,-,-,-,-,-,TOTALBITS_24,-,-,-,-,-,-,-,TOTALBITS_32,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-" textline " " bitfld.long 0x00 3. " CLOCKDISABLE ,Deactivates most internal clocks of fetch unit" "OPERATION,POWERDOWN" bitfld.long 0x00 2. " SWRESET ,Puts the fetch unit in software reset" "OPERATION,SW_RESET" textline " " bitfld.long 0x00 1. " START ,Writing a '1' starts processing" "Stopped,Started" bitfld.long 0x00 0. " SHADOWLOAD ,Set this to '1' if you want the fetch unit to perform a shadow load with the next start of operation" "0,1" else group.long 0x44++0x03 line.long 0x00 "CONTROL,Fetch unit main control register" bitfld.long 0x00 31. " SHD_UPD ,Overrides the standard shadow load mechanisms and constantly loads shadows" "Normal,Update" rbitfld.long 0x00 30. " HASMULTIPLY ,This field can be used to determine if this fetch can perform color multiplications" "MULTIPLY,NO_MULTIPLY" textline " " rbitfld.long 0x00 28.--29. " FETCHTYPE ,This field can be used to determine what kind of fetch unit this is" "SIMPLE,RLD,ROT," bitfld.long 0x00 24. " RLDENABLE ,Enables use of the Run Length Decompression feature" "Enabled,Disabled" textline " " bitfld.long 0x00 23. " RLDCMDCOMP ,Enables use of the Command Compatibility Mode with the Run Length Decompression feature" "Disabled,Enabled" bitfld.long 0x00 21.--22. " TILEMODE ,Select the tile mode for pixels outside the source buffer" "TILE_PAD,TILE_FILL_CONSTANT,TILE_FILL_ZERO," textline " " bitfld.long 0x00 20. " DUMMYSKIPSELECT ,Select which values to use for skipped pixels inside the skip rectangle" "CONSTANTCOLOR,ZERO" bitfld.long 0x00 17. " TOGGLEFIELD ,Enable toggling of the field bit of the command word output to the pixel pipeline between frames" "Disabled,Enabled" textline " " bitfld.long 0x00 16. " SETFIELD ,The fld control bit of the start of frame control word of the pixel pipeline" "0,1" bitfld.long 0x00 12. " ALPHAMULTIPLY ,Enable multiplication of pixel alpha withconstant alpha" "Disabled,Enabled" textline " " bitfld.long 0x00 10.--11. " ENDIANSWAP ,Configure the endian swap on the 64 bit word" "Disabled,Word_16bit,Word_32bit,Word_64bit" bitfld.long 0x00 4.--9. " BITSPERPIXEL ,Pixel size in bits has to be a power of two or 24" "-,TOTALBITS_1,TOTALBITS_2,-,TOTALBITS_4,-,-,-,TOTALBITS_8,-,-,-,-,-,-,-,TOTALBITS_16,-,-,-,-,-,-,-,TOTALBITS_24,-,-,-,-,-,-,-,TOTALBITS_32,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-" textline " " bitfld.long 0x00 3. " CLOCKDISABLE ,Deactivates most internal clocks of fetch unit" "OPERATION,POWERDOWN" bitfld.long 0x00 2. " SWRESET ,Puts the fetch unit in software reset" "OPERATION,SW_RESET" textline " " bitfld.long 0x00 1. " START ,Writing a '1' starts processing" "Stopped,Started" bitfld.long 0x00 0. " SHADOWLOAD ,Set this to '1' if you want the fetch unit to perform a shadow load with the next start of operation" "0,1" endif tree.end width 24. tree "Fetch 1" group.long 0x400++0x0F line.long 0x00 "BURSTBUFFERMANAGEMENT,AXI interface buffer management register" bitfld.long 0x00 24.--28. " SETBURSTLENGTH ,Set this to the burst length that should be used on the AXI interface" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.byte 0x00 16.--23. 1. " SETNUMBUFFERS ,Set this to the number of bursts that should be buffered" textline " " rbitfld.long 0x00 8.--12. " BURSTLENGTHFORMAXBUFFERS ,Maximum Burst Length that can be used when ManagedBurstBuffers burst buffers are used" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.byte 0x00 0.--7. 1. " MANAGEDBURSTBUFFERS ,Maximum number of burst buffers that can be administrated in the AXI interface" line.long 0x04 "BASEADDRESS,Source buffer base address" line.long 0x08 "SOURCEBUFFERSTRIDE,Source buffer stride" hexmask.long.word 0x08 0.--13. 1. " STRIDE ,Source buffer stride in bytes minus one used for address generation" line.long 0x0C "SOURCEBUFFERATTRIBUTES,Source buffer attributes" hexmask.long.word 0x0C 16.--27. 1. " LINECOUNT ,Number of lines of the source buffer minus one needed for tiling" hexmask.long.word 0x0C 0.--11. 1. " LINEWIDTH ,Width of the source buffer in pixels minus one needed for tiling" sif (cpu()=="MB86R11F") if (((per.l(ad:0x38C00000+0x444))&0x30000000)==0x10000000) group.long 0x410++0x03 line.long 0x00 "SOURCEBUFFERLENGTH,Source Buffer Length for Run Length Decoding" hexmask.long 0x00 0.--24. 1. " RLEWORDS ,Number of 32-bit words minus one that are required to decode the run length encoded source buffer" else hgroup.long 0x410++0x03 hide.long 0x00 "SOURCEBUFFERLENGTH,Source Buffer Length for Run Length Decoding" in endif endif group.long 0x414++0x07 line.long 0x00 "FRAMEXOFFSET,Frame X offset" hexmask.long.word 0x00 16.--29. 1. " FRAMEXOFFSET ,Frame X origin offset relative to the source buffer origin" line.long 0x04 "FRAMEYOFFSET,Frame Y offset" hexmask.long.word 0x04 16.--29. 1. " FRAMEYOFFSET ,Frame Y origin offset relative to the source buffer origin" if (((per.l(ad:0x38C00000+0x444))&0x30000000)==0x20000000) group.long 0x41C++0x03 line.long 0x00 "FRAMEDIMENSIONS,Defines frame rectangle" hexmask.long.word 0x00 16.--27. 1. " FRAMEHEIGHT ,Frame height minus one" hexmask.long.word 0x00 0.--11. 1. " FRAMEWIDTH ,Frame width minus one" hgroup.long 0x420++0x07 hide.long 0x00 "DELTAXX,DeltaXX stepsize" in hide.long 0x04 "DELTAYY,DeltaYY stepsize" in else group.long 0x41C++0x03 line.long 0x00 "FRAMEDIMENSIONS,Defines frame rectangle" bitfld.long 0x00 31. " FRAMESWAPDIRECTIONS ,Swaps X and Y directions" "0,1" hexmask.long.word 0x00 16.--27. 1. " FRAMEHEIGHT ,Frame height minus one" textline " " hexmask.long.word 0x00 0.--11. 1. " FRAMEWIDTH ,Frame width minus one" group.long 0x420++0x07 line.long 0x00 "DELTAXX,DeltaXX stepsize" bitfld.long 0x00 14.--19. " DELTAX ,DELTAX stepsize for repetition operation given in signed fixed-point 4.2 two's complement notation" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x04 "DELTAYY,DeltaYY stepsize" bitfld.long 0x04 14.--19. " DELTAY ,DeltaY stepsize for repetition operation given in signed fixed-point 4.2 two's complement notation" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" endif group.long 0x430++0x13 line.long 0x00 "SKIPWINDOWOFFSET,Skip window offset" hexmask.long.word 0x00 16.--27. 1. " SKIPWINDOWYOFFSET ,Skip window Y offset relative to the source buffer origin" hexmask.long.word 0x00 0.--11. 1. " SKIPWINDOWXOFFSET ,Skip window X offset relative to the source buffer origin" line.long 0x04 "SKIPWINDOWDIMENSIONS,Defines skip window rectangle" hexmask.long.word 0x04 16.--27. 1. " SKIPWINDOWHEIGHT ,Skip window height" hexmask.long.word 0x04 0.--11. 1. " SKIPWINDOWWIDTH ,Skip window width" line.long 0x08 "COLORCOMPONENTBITS,Color component size of source buffer" bitfld.long 0x08 24.--27. " COMPONENTBITSRED ,ComponentBitsRed" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x08 16.--19. " COMPONENTBITSGREEN ,ComponentBitsGreen" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x08 8.--11. " COMPONENTBITSBLUE ,ComponentBitsBlue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x08 0.--3. " COMPONENTBITSALPHA ,ComponentBitsAlpha" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x0C "COLORCOMPONENTSHIFT,Color component offset of source buffer" bitfld.long 0x0C 24.--28. " COMPONENTSHIFTRED ,ComponentShiftRed" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0C 16.--20. " COMPONENTSHIFTGREEN ,ComponentShiftGreen" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0C 8.--12. " COMPONENTSHIFTBLUE ,ComponentShiftBlue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0C 0.--4. " COMPONENTSHIFTALPHA ,ComponentShiftAlpha" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x10 "CONSTANTCOLOR,Constant color settings" hexmask.long.byte 0x10 24.--31. 1. " CONSTANTCOLORRED ,ConstantColorRed" hexmask.long.byte 0x10 16.--23. 1. " CONSTANTCOLORGREEN ,ConstantColorGreen" textline " " hexmask.long.byte 0x10 8.--15. 1. " CONSTANTCOLORBLUE ,ConstantColorBlue" hexmask.long.byte 0x10 0.--7. 1. " CONSTANTCOLORALPHA ,ConstantColorAlpha" group.long 0x444++0x03 line.long 0x00 "CONTROL,Fetch unit main control register" bitfld.long 0x00 31. " SHD_UPD ,Overrides the standard shadow load mechanisms and constantly loads shadows" "Normal,Update" rbitfld.long 0x00 30. " HASMULTIPLY ,This field can be used to determine if this fetch can perform color multiplications" "MULTIPLY,NO_MULTIPLY" textline " " rbitfld.long 0x00 28.--29. " FETCHTYPE ,This field can be used to determine what kind of fetch unit this is" "SIMPLE,RLD,ROT," bitfld.long 0x00 21.--22. " TILEMODE ,Select the tile mode for pixels outside the source buffer" "TILE_PAD,TILE_FILL_CONSTANT,TILE_FILL_ZERO," textline " " bitfld.long 0x00 20. " DUMMYSKIPSELECT ,Select which values to use for skipped pixels inside the skip rectangle" "CONSTANTCOLOR,ZERO" bitfld.long 0x00 17. " TOGGLEFIELD ,Enable toggling of the field bit of the command word output to the pixel pipeline between frames" "Disabled,Enabled" textline " " bitfld.long 0x00 16. " SETFIELD ,The fld control bit of the start of frame control word of the pixel pipeline" "0,1" bitfld.long 0x00 12. " ALPHAMULTIPLY ,Enable multiplication of pixel alpha withconstant alpha" "Disabled,Enabled" textline " " bitfld.long 0x00 4.--9. " BITSPERPIXEL ,Pixel size in bits has to be a power of two or 24" "-,TOTALBITS_1,TOTALBITS_2,-,TOTALBITS_4,-,-,-,TOTALBITS_8,-,-,-,-,-,-,-,TOTALBITS_16,-,-,-,-,-,-,-,TOTALBITS_24,-,-,-,-,-,-,-,TOTALBITS_32,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-" bitfld.long 0x00 3. " CLOCKDISABLE ,Deactivates most internal clocks of fetch unit" "OPERATION,POWERDOWN" textline " " bitfld.long 0x00 2. " SWRESET ,Puts the fetch unit in software reset" "OPERATION,SW_RESET" bitfld.long 0x00 1. " START ,Writing a '1' starts processing" "Stopped,Started" textline " " bitfld.long 0x00 0. " SHADOWLOAD ,Set this to '1' if you want the fetch unit to perform a shadow load with the next start of operation" "0,1" tree.end tree "Fetch 2" width 24. group.long 0x800++0x0F line.long 0x00 "BURSTBUFFERMANAGEMENT,AXI interface buffer management register" bitfld.long 0x00 24.--28. " SETBURSTLENGTH ,Set this to the burst length that should be used on the AXI interface" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.byte 0x00 16.--23. 1. " SETNUMBUFFERS ,Set this to the number of bursts that should be buffered" textline " " rbitfld.long 0x00 8.--12. " BURSTLENGTHFORMAXBUFFERS ,Maximum Burst Length that can be used when ManagedBurstBuffers burst buffers are used" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.byte 0x00 0.--7. 1. " MANAGEDBURSTBUFFERS ,Maximum number of burst buffers that can be administrated in the AXI interface" line.long 0x04 "BASEADDRESS,Source buffer base address" line.long 0x08 "SOURCEBUFFERSTRIDE,Source buffer stride" hexmask.long.word 0x08 0.--13. 1. " STRIDE ,Source buffer stride in bytes minus one used for address generation" line.long 0x0C "SOURCEBUFFERATTRIBUTES,Source buffer attributes" hexmask.long.word 0x0C 16.--27. 1. " LINECOUNT ,Number of lines of the source buffer minus one needed for tiling" hexmask.long.word 0x0C 0.--11. 1. " LINEWIDTH ,Width of the source buffer in pixels minus one needed for tiling" sif (cpu()=="MB86R11F") if (((per.l(ad:0x38C00000+0x84C))&0x30000000)==0x10000000) group.long 0x810++0x03 line.long 0x00 "SOURCEBUFFERLENGTH,Source Buffer Length for Run Length Decoding" hexmask.long 0x00 0.--24. 1. " RLEWORDS ,Number of 32-bit words minus one that are required to decode the run length encoded source buffer" else hgroup.long 0x810++0x03 hide.long 0x00 "SOURCEBUFFERLENGTH,Source Buffer Length for Run Length Decoding" in endif endif if (((per.l(ad:0x38C00000+0x84C))&0x30000000)==0x20000000) group.long 0x814++0x07 line.long 0x00 "FRAMEXOFFSET,Frame X offset" hexmask.long.word 0x00 16.--29. 1. " FRAMEXOFFSET ,Frame X origin offset relative to the source buffer origin" textline " " bitfld.long 0x00 11.--15. " FRAMEXOFFSETDECIMALPLACES ,Ufix 0 Fractional bits of the X Offset" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x04 "FRAMEYOFFSET,Frame Y offset" hexmask.long.word 0x04 16.--29. 1. " FRAMEYOFFSET ,Frame Y origin offset relative to the source buffer origin" textline " " bitfld.long 0x04 11.--15. " FRAMEYOFFSETDECIMALPLACES ,Ufix 0 Fractional bits of the Y Offset" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" else group.long 0x814++0x07 line.long 0x00 "FRAMEXOFFSET,Frame X offset" hexmask.long.word 0x00 16.--29. 1. " FRAMEXOFFSET ,Frame X origin offset relative to the source buffer origin" line.long 0x04 "FRAMEYOFFSET,Frame Y offset" hexmask.long.word 0x04 16.--29. 1. " FRAMEYOFFSET ,Frame Y origin offset relative to the source buffer origin" endif group.long 0x81C++0x03 line.long 0x00 "FRAMEDIMENSIONS,Defines frame rectangle" hexmask.long.word 0x00 16.--27. 1. " FRAMEHEIGHT ,Frame height minus one" hexmask.long.word 0x00 0.--11. 1. " FRAMEWIDTH ,Frame width minus one" if (((per.l(ad:0x38C00000+0x84C))&0x30000000)==0x20000000) group.long 0x820++0x0F line.long 0x00 "DELTAXX,DeltaXX stepsize" hexmask.long.tbyte 0x00 0.--22. 1. " DELTAXX ,DeltaXX stepsize for repetition operation given in signed fixed-point 7.16 two's complement notation" line.long 0x04 "DELTAXY,DeltaXY stepsize" hexmask.long.tbyte 0x04 0.--22. 1. " DELTAXY ,DeltaXY stepsize for repetition operation given in signed fixed-point 7.16 two's complement notation" line.long 0x08 "DELTAYX,DeltaYX stepsize" hexmask.long.tbyte 0x08 0.--22. 1. " DELTAYX ,DeltaYX stepsize for repetition operation given in signed fixed-point 7.16 two's complement notation" line.long 0x0C "DELTAYY,DeltaYY stepsize" hexmask.long.tbyte 0x0C 0.--22. 1. " DELTAYY ,DeltaYY stepsize for repetition operation given in signed fixed-point 7.16 two's complement notation" else hgroup.long 0x820++0x0F hide.long 0x00 "DELTAXX,DeltaXX stepsize" hide.long 0x04 "DELTAXY,DeltaXY stepsize" hide.long 0x08 "DELTAYX,DeltaYX stepsize" hide.long 0x0C "DELTAYY,DeltaYY stepsize" endif group.long 0x830++0x13 line.long 0x00 "SKIPWINDOWOFFSET,Skip window offset" hexmask.long.word 0x00 16.--27. 1. " SKIPWINDOWYOFFSET ,Skip window Y offset relative to the source buffer origin" hexmask.long.word 0x00 0.--11. 1. " SKIPWINDOWXOFFSET ,Skip window X offset relative to the source buffer origin" line.long 0x04 "SKIPWINDOWDIMENSIONS,Defines skip window rectangle" hexmask.long.word 0x04 16.--27. 1. " SKIPWINDOWHEIGHT ,Skip window height" hexmask.long.word 0x04 0.--11. 1. " SKIPWINDOWWIDTH ,Skip window width" line.long 0x08 "COLORCOMPONENTBITS,Color component size of source buffer" bitfld.long 0x08 24.--27. " COMPONENTBITSRED ,ComponentBitsRed" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x08 16.--19. " COMPONENTBITSGREEN ,ComponentBitsGreen" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x08 8.--11. " COMPONENTBITSBLUE ,ComponentBitsBlue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x08 0.--3. " COMPONENTBITSALPHA ,ComponentBitsAlpha" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x0C "COLORCOMPONENTSHIFT,Color component offset of source buffer" bitfld.long 0x0C 24.--28. " COMPONENTSHIFTRED ,ComponentShiftRed" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0C 16.--20. " COMPONENTSHIFTGREEN ,ComponentShiftGreen" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0C 8.--12. " COMPONENTSHIFTBLUE ,ComponentShiftBlue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0C 0.--4. " COMPONENTSHIFTALPHA ,ComponentShiftAlpha" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x10 "CONSTANTCOLOR,Constant color settings" hexmask.long.byte 0x10 24.--31. 1. " CONSTANTCOLORRED ,ConstantColorRed" hexmask.long.byte 0x10 16.--23. 1. " CONSTANTCOLORGREEN ,ConstantColorGreen" textline " " hexmask.long.byte 0x10 8.--15. 1. " CONSTANTCOLORBLUE ,ConstantColorBlue" hexmask.long.byte 0x10 0.--7. 1. " CONSTANTCOLORALPHA ,ConstantColorAlpha" group.long 0x844++0x07 line.long 0x00 "FIRPOSITIONS,FIR Sequence control register" bitfld.long 0x00 12.--15. " FIRPOSITION3 ,Selects the position of the fourth FIR input pixel in the 4*4 FIR input array of the fetch rot" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 8.--11. " FIRPOSITION2 ,Selects the position of the third FIR input pixel in the 4*4 FIR input array of the fetch rot" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 4.--7. " FIRPOSITION1 ,Selects the position of the second FIR input pixel in the 4*4 FIR input array of the fetch rot" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 0.--3. " FIRPOSITION0 ,Selects the position of the first FIR input pixel in the 4*4 FIR input array of the fetch rot" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x04 "FIRCOEFFICIENTS,FIR coefficients register" hexmask.long.byte 0x04 24.--31. 1. " FIRCOEFFICIENT3 ,Specifies the fourth FIR coefficient for fetch rot FIR operations" hexmask.long.byte 0x04 16.--23. 1. " FIRCOEFFICIENT2 ,Specifies the third FIR coefficient for fetch rot FIR operations" textline " " hexmask.long.byte 0x04 8.--15. 1. " FIRCOEFFICIENT1 ,Specifies the second FIR coefficient for fetch rot FIR operations" hexmask.long.byte 0x04 0.--7. 1. " FIRCOEFFICIENT0 ,Specifies the first FIR coefficient for fetch rot FIR operations" if ((((per.l(ad:0x38C00000+0x84C))&0x30000000)==0x20000000)&&(((per.l(ad:0x38C00000+0x84C))&0x40000000)==0x00000000)) group.long 0x84C++0x03 line.long 0x00 "Control,Fetch unit main control register" bitfld.long 0x00 31. " SHD_UPD ,Overrides the standard shadow load mechanisms and constantly loads shadows" "Normal,Update" rbitfld.long 0x00 30. " HASMULTIPLY ,This field can be used to determine if this fetch can perform color multiplications" "MULTIPLY,NO_MULTIPLY" textline " " rbitfld.long 0x00 28.--29. " FETCHTYPE ,This field can be used to determine what kind of fetch unit this is" "SIMPLE,RLD,ROT," bitfld.long 0x00 25.--26. " FILTERMODE ,Use this to select between nearest and bilinear filtering" "NEAREST,BILINEAR,FIR2,FIR4" textline " " bitfld.long 0x00 21.--22. " TILEMODE ,Select the tile mode for pixels outside the source buffer" "TILE_PAD,TILE_FILL_CONSTANT,TILE_FILL_ZERO," bitfld.long 0x00 20. " DUMMYSKIPSELECT ,Select which values to use for skipped pixels inside the skip rectangle" "CONSTANTCOLOR,ZERO" textline " " bitfld.long 0x00 19. " GAMMAAPPLYENABLE ,Enable gamma correction stage to apply gamma" "Disabled,Enabled" bitfld.long 0x00 18. " GAMMAREMOVEENABLE ,Enable gamma correction stage to remove gamma" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " TOGGLEFIELD ,Enable toggling of the field bit of the command word output to the pixel pipeline between frames" "Disabled,Enabled" bitfld.long 0x00 16. " SETFIELD ,The fld control bit of the start of frame control word of the pixel pipeline" "0,1" textline " " bitfld.long 0x00 14. " COLORMULTIPLYSELECT ,Select which multiplicator to use for color multiply" "ALPHA,CONSTANTCOLOR" bitfld.long 0x00 13. " COLORMULTIPLYENABLE ,Enable multiplication of color values after constant alpha multiplication stage" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " ALPHAMULTIPLY ,Enable multiplication of pixel alpha withconstant alpha" "Disabled,Enabled" bitfld.long 0x00 4.--9. " BITSPERPIXEL ,Pixel size in bits has to be a power of two or 24" "-,TOTALBITS_1,TOTALBITS_2,-,TOTALBITS_4,-,-,-,TOTALBITS_8,-,-,-,-,-,-,-,TOTALBITS_16,-,-,-,-,-,-,-,TOTALBITS_24,-,-,-,-,-,-,-,TOTALBITS_32,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-" textline " " bitfld.long 0x00 3. " CLOCKDISABLE ,Deactivates most internal clocks of fetch unit" "OPERATION,POWERDOWN" bitfld.long 0x00 2. " SWRESET ,Puts the fetch unit in software reset" "OPERATION,SW_RESET" textline " " bitfld.long 0x00 1. " START ,Writing a '1' starts processing" "Stopped,Started" bitfld.long 0x00 0. " SHADOWLOAD ,Set this to '1' if you want the fetch unit to perform a shadow load with the next start of operation" "0,1" elif ((((per.l(ad:0x38C00000+0x84C))&0x30000000)==0x20000000)&&(((per.l(ad:0x38C00000+0x84C))&0x40000000)==0x40000000)) group.long 0x84C++0x03 line.long 0x00 "CONTROL,Fetch unit main control register" bitfld.long 0x00 31. " SHD_UPD ,Overrides the standard shadow load mechanisms and constantly loads shadows" "Normal,Update" rbitfld.long 0x00 30. " HASMULTIPLY ,This field can be used to determine if this fetch can perform color multiplications" "MULTIPLY,NO_MULTIPLY" textline " " rbitfld.long 0x00 28.--29. " FETCHTYPE ,This field can be used to determine what kind of fetch unit this is" "SIMPLE,RLD,ROT," bitfld.long 0x00 25.--26. " FILTERMODE ,Use this to select between nearest and bilinear filtering" "NEAREST,BILINEAR,FIR2,FIR4" textline " " bitfld.long 0x00 21.--22. " TILEMODE ,Select the tile mode for pixels outside the source buffer" "TILE_PAD,TILE_FILL_CONSTANT,TILE_FILL_ZERO," bitfld.long 0x00 20. " DUMMYSKIPSELECT ,Select which values to use for skipped pixels inside the skip rectangle" "CONSTANTCOLOR,ZERO" textline " " bitfld.long 0x00 19. " GAMMAAPPLYENABLE ,Enable gamma correction stage to apply gamma" "Disabled,Enabled" bitfld.long 0x00 18. " GAMMAREMOVEENABLE ,Enable gamma correction stage to remove gamma" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " TOGGLEFIELD ,Enable toggling of the field bit of the command word output to the pixel pipeline between frames" "Disabled,Enabled" bitfld.long 0x00 16. " SETFIELD ,The fld control bit of the start of frame control word of the pixel pipeline" "0,1" textline " " bitfld.long 0x00 12. " ALPHAMULTIPLY ,Enable multiplication of pixel alpha withconstant alpha" "Disabled,Enabled" bitfld.long 0x00 4.--9. " BITSPERPIXEL ,Pixel size in bits has to be a power of two or 24" "-,TOTALBITS_1,TOTALBITS_2,-,TOTALBITS_4,-,-,-,TOTALBITS_8,-,-,-,-,-,-,-,TOTALBITS_16,-,-,-,-,-,-,-,TOTALBITS_24,-,-,-,-,-,-,-,TOTALBITS_32,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-" textline " " bitfld.long 0x00 3. " CLOCKDISABLE ,Deactivates most internal clocks of fetch unit" "OPERATION,POWERDOWN" bitfld.long 0x00 2. " SWRESET ,Puts the fetch unit in software reset" "OPERATION,SW_RESET" textline " " bitfld.long 0x00 1. " START ,Writing a '1' starts processing" "Stopped,Started" bitfld.long 0x00 0. " SHADOWLOAD ,Set this to '1' if you want the fetch unit to perform a shadow load with the next start of operation" "0,1" elif ((((per.l(ad:0x38C00000+0x84C))&0x30000000)!=0x20000000)&&(((per.l(ad:0x38C00000+0x84C))&0x40000000)==0x00000000)) group.long 0x84C++0x03 line.long 0x00 "CONTROL,Fetch unit main control register" bitfld.long 0x00 31. " SHD_UPD ,Overrides the standard shadow load mechanisms and constantly loads shadows" "Normal,Update" rbitfld.long 0x00 30. " HASMULTIPLY ,This field can be used to determine if this fetch can perform color multiplications" "MULTIPLY,NO_MULTIPLY" textline " " rbitfld.long 0x00 28.--29. " FETCHTYPE ,This field can be used to determine what kind of fetch unit this is" "SIMPLE,RLD,ROT," textline " " bitfld.long 0x00 21.--22. " TILEMODE ,Select the tile mode for pixels outside the source buffer" "TILE_PAD,TILE_FILL_CONSTANT,TILE_FILL_ZERO," bitfld.long 0x00 20. " DUMMYSKIPSELECT ,Select which values to use for skipped pixels inside the skip rectangle" "CONSTANTCOLOR,ZERO" textline " " bitfld.long 0x00 19. " GAMMAAPPLYENABLE ,Enable gamma correction stage to apply gamma" "Disabled,Enabled" bitfld.long 0x00 18. " GAMMAREMOVEENABLE ,Enable gamma correction stage to remove gamma" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " TOGGLEFIELD ,Enable toggling of the field bit of the command word output to the pixel pipeline between frames" "Disabled,Enabled" bitfld.long 0x00 16. " SETFIELD ,The fld control bit of the start of frame control word of the pixel pipeline" "0,1" textline " " bitfld.long 0x00 14. " COLORMULTIPLYSELECT ,Select which multiplicator to use for color multiply" "ALPHA,CONSTANTCOLOR" bitfld.long 0x00 13. " COLORMULTIPLYENABLE ,Enable multiplication of color values after constant alpha multiplication stage" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " ALPHAMULTIPLY ,Enable multiplication of pixel alpha withconstant alpha" "Disabled,Enabled" bitfld.long 0x00 4.--9. " BITSPERPIXEL ,Pixel size in bits has to be a power of two or 24" "-,TOTALBITS_1,TOTALBITS_2,-,TOTALBITS_4,-,-,-,TOTALBITS_8,-,-,-,-,-,-,-,TOTALBITS_16,-,-,-,-,-,-,-,TOTALBITS_24,-,-,-,-,-,-,-,TOTALBITS_32,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-" textline " " bitfld.long 0x00 3. " CLOCKDISABLE ,Deactivates most internal clocks of fetch unit" "OPERATION,POWERDOWN" bitfld.long 0x00 2. " SWRESET ,Puts the fetch unit in software reset" "OPERATION,SW_RESET" textline " " bitfld.long 0x00 1. " START ,Writing a '1' starts processing" "Stopped,Started" bitfld.long 0x00 0. " SHADOWLOAD ,Set this to '1' if you want the fetch unit to perform a shadow load with the next start of operation" "0,1" else group.long 0x84C++0x03 line.long 0x00 "CONTROL,Fetch unit main control register" bitfld.long 0x00 31. " SHD_UPD ,Overrides the standard shadow load mechanisms and constantly loads shadows" "Normal,Update" rbitfld.long 0x00 30. " HASMULTIPLY ,This field can be used to determine if this fetch can perform color multiplications" "MULTIPLY,NO_MULTIPLY" textline " " rbitfld.long 0x00 28.--29. " FETCHTYPE ,This field can be used to determine what kind of fetch unit this is" "SIMPLE,RLD,ROT," textline " " bitfld.long 0x00 21.--22. " TILEMODE ,Select the tile mode for pixels outside the source buffer" "TILE_PAD,TILE_FILL_CONSTANT,TILE_FILL_ZERO," bitfld.long 0x00 20. " DUMMYSKIPSELECT ,Select which values to use for skipped pixels inside the skip rectangle" "CONSTANTCOLOR,ZERO" textline " " bitfld.long 0x00 19. " GAMMAAPPLYENABLE ,Enable gamma correction stage to apply gamma" "Disabled,Enabled" bitfld.long 0x00 18. " GAMMAREMOVEENABLE ,Enable gamma correction stage to remove gamma" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " TOGGLEFIELD ,Enable toggling of the field bit of the command word output to the pixel pipeline between frames" "Disabled,Enabled" bitfld.long 0x00 16. " SETFIELD ,The fld control bit of the start of frame control word of the pixel pipeline" "0,1" textline " " bitfld.long 0x00 12. " ALPHAMULTIPLY ,Enable multiplication of pixel alpha withconstant alpha" "Disabled,Enabled" bitfld.long 0x00 4.--9. " BITSPERPIXEL ,Pixel size in bits has to be a power of two or 24" "-,TOTALBITS_1,TOTALBITS_2,-,TOTALBITS_4,-,-,-,TOTALBITS_8,-,-,-,-,-,-,-,TOTALBITS_16,-,-,-,-,-,-,-,TOTALBITS_24,-,-,-,-,-,-,-,TOTALBITS_32,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-,-" textline " " bitfld.long 0x00 3. " CLOCKDISABLE ,Deactivates most internal clocks of fetch unit" "OPERATION,POWERDOWN" bitfld.long 0x00 2. " SWRESET ,Puts the fetch unit in software reset" "OPERATION,SW_RESET" textline " " bitfld.long 0x00 1. " START ,Writing a '1' starts processing" "Stopped,Started" bitfld.long 0x00 0. " SHADOWLOAD ,Set this to '1' if you want the fetch unit to perform a shadow load with the next start of operation" "0,1" endif tree.end tree "Store 0" width 25. group.long 0xC00++0x0F line.long 0x00 "BURSTBUFFERMANAGEMENT,AXI interface buffer management register" bitfld.long 0x00 24.--28. " SETBURSTLENGTH ,Set this to the burst length that should be used on the AXI interface" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " rbitfld.long 0x00 8.--12. " MAXBURSTLENGTH ,Maximum Burst Length that can be used when ManagedBurstBuffers burst buffers are used" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.byte 0x00 0.--7. 1. " MANAGEDBURSTBUFFERS ,Maximum number of burst buffers that can be administrated in the AXI interface" line.long 0x04 "BASEADDRESS,Destination buffer base address" line.long 0x08 "DESTINATIONBUFFERSTRIDE,Destination buffer stride" hexmask.long.word 0x08 0.--13. 1. " STRIDE ,Source buffer stride in bytes minus one used for address generation" group.long 0xC14++0x07 line.long 0x00 "FRAMEXOFFSET,Frame X offset" hexmask.long.word 0x00 16.--27. 1. " FRAMEXOFFSET ,Frame X origin offset relative to the destination buffer origin" line.long 0x04 "FRAMEYOFFSET ,Frame Y offset" hexmask.long.word 0x04 16.--27. 1. " FRAMEYOFFSET ,Frame Y origin offset relative to the destination buffer origin" group.long 0xC38++0x07 line.long 0x00 "COLORCOMPONENTBITS,Color component size of destination buffer" bitfld.long 0x00 24.--27. " COMPONENTBITSRED ,ComponentBitsRed" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 16.--19. " COMPONENTBITSGREEN ,ComponentBitsGreen" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 8.--11. " COMPONENTBITSBLUE ,ComponentBitsBlue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 0.--3. " COMPONENTBITSALPHA ,ComponentBitsAlpha" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x04 "COLORCOMPONENTSHIFT,Color component offset of destination buffer" bitfld.long 0x04 24.--28. " COMPONENTSHIFTRED ,ComponentShiftRed" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x04 16.--20. " COMPONENTSHIFTGREEN ,ComponentShiftGreen" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x04 8.--12. " COMPONENTSHIFTBLUE ,ComponentShiftBlue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x04 0.--4. " COMPONENTSHIFTALPHA ,ComponentShiftAlpha" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0xC4C++0x03 line.long 0x00 "CONTROL,Store unit main control register" bitfld.long 0x00 31. " SHD_UPD ,Overrides the standard shadow load mechanisms and constantly loads shadows" "Normal,Update" bitfld.long 0x00 13. " ALPHADITHERENABLE ,Specifies whether dithering or LSB truncation" "LSBTRUNK,DITHER" textline " " bitfld.long 0x00 12. " COLORDITHERENABLE ,Specifies whether dithering or LSB truncation" "LSBTRUNK,DITHER" hexmask.long.byte 0x00 4.--10. 1. " BITSPERPIXEL ,Pixel size in bits has to be a power of two or 24" textline " " bitfld.long 0x00 3. " CLOCKDISABLE ,Deactivates most internal clocks of store unit" "OPERATION,POWERDOWN" bitfld.long 0x00 2. " SWRESET ,Puts the store unit in software reset" "OPERATION,SW_RESET" textline " " eventfld.long 0x00 0. " START ,Writing a one starts processing of the pixel engine" "0,1" rgroup.long 0xC50++0x07 line.long 0x00 "LAST_CONTROL_WORD,Shows the last control word received" line.long 0x04 "PERFCOUNTER,Performance counter result" tree.end tree "Rop 0" width 24. group.long 0x1000++0x7 line.long 0x00 "CONTROL,Raster Operation control register" bitfld.long 0x00 31. " SHD_UPD ,Overrides the standard shadow load mechanisms and constantly loads shadows" "NORMAL,UPDATE" bitfld.long 0x00 10. " TERTDIV2 ,Selects whether to divide the tertiary input color components by two or not for ADD mode" "BYPASS,DIVIDEBY2" textline " " bitfld.long 0x00 9. " SECDIV2 ,Selects whether to divide the secondary input color components by two or not for ADD mode" "BYPASS,DIVIDEBY2" bitfld.long 0x00 8. " PRIMDIV2 ,Selects whether to divide the primary input color components by two or not for ADD mode" "BYPASS,DIVIDEBY2" textline " " bitfld.long 0x00 7. " REDMODE ,Selects the mode for the red component channel" "ROP,ADD" bitfld.long 0x00 6. " GREENMODE ,Selects the mode for the green component channel" "ROP,ADD" textline " " bitfld.long 0x00 5. " BLUEMODE ,Selects the mode for the blue component channel" "ROP,ADD" bitfld.long 0x00 4. " ALPHAMODE ,Selects the mode for the alpha component channel" "ROP,ADD" textline " " bitfld.long 0x00 0. " MODE ,Operation mode for rop" "NEUTRAL,OPERATION" line.long 0x04 "RASTEROPERATIONINDICES,ROP operation indices" hexmask.long.byte 0x04 24.--31. 1. " OPINDEXRED ,OpIndexRed" hexmask.long.byte 0x04 16.--23. 1. " OPINDEXGREEN ,OpIndexGreen" textline " " hexmask.long.byte 0x04 8.--15. 1. " OPINDEXBLUE ,OpIndexBlue" hexmask.long.byte 0x04 0.--7. 1. " OPINDEXALPHA ,OpIndexAlpha" rgroup.long 0x1008++0xB line.long 0x00 "PRIM_CONTROL_WORD,Value of last received primary control word" line.long 0x04 "SEC_CONTROL_WORD,Value of last received secondary control word" line.long 0x08 "TERT_CONTROL_WORD,Value of last received tertiary control word" width 25. tree.end tree "Blitblend 0" group.long 0x1400++0x1F line.long 0x00 "CONTROL,BlitBlend control register" bitfld.long 0x00 31. " SHD_UPD ,Overrides the standard shadow load mechanisms and constantly loads shadows" "NORMAL,UPDATE" bitfld.long 0x00 0. " MODE ,Operation mode for BlitBlend" "NEUTRAL,OPERATION" line.long 0x04 "CONSTANTCOLOR,Constant color for blend operations" hexmask.long.byte 0x04 24.--31. 1. " CONSTANTCOLORRED ,ConstantColorRed" hexmask.long.byte 0x04 16.--23. 1. " CONSTANTCOLORGREEN ,ConstantColorGreen" textline " " hexmask.long.byte 0x04 8.--15. 1. " CONSTANTCOLORBLUE ,ConstantColorBlue" hexmask.long.byte 0x04 0.--7. 1. " CONSTANTCOLORALPHA ,ConstantColorAlpha" line.long 0x08 "COLORREDBLENDFUNCTION,Open GL RGB blending factors" hexmask.long.word 0x08 16.--31. 1. " BLENDFUNCCOLORREDDST ,BlendFuncColorRedDst" hexmask.long.word 0x08 0.--15. 1. " BLENDFUNCCOLORREDSRC ,BlendFuncColorRedSrc" line.long 0x0C "COLORGREENBLENDFUNCTION,Open GL RGB blending factors" hexmask.long.word 0x0C 16.--31. 1. " BLENDFUNCCOLORGREENDST ,BlendFuncColorGreenDst" hexmask.long.word 0x0C 0.--15. 1. " BLENDFUNCCOLORGREENSRC ,BlendFuncColorGreenSrc" line.long 0x10 "COLORBLUEBLENDFUNCTION,Open GL RGB blending factors" hexmask.long.word 0x10 16.--31. 1. " BLENDFUNCCOLORBLUEDST ,BlendFuncColorBlueDst" hexmask.long.word 0x10 0.--15. 1. " BLENDFUNCCOLORBLUESRC ,BlendFuncColorBlueSrc" line.long 0x14 "ALPHABLENDFUNCTION,Open GL alpha blending factors" hexmask.long.word 0x14 16.--31. 1. " BLENDFUNCALPHADST ,BlendFuncAlphaDst" hexmask.long.word 0x14 0.--15. 1. " BLENDFUNCALPHASRC ,BlendFuncAlphaSrc" line.long 0x18 "BLENDMODE1,Open GL and Open VG blending modes for colors red and green" hexmask.long.word 0x18 16.--31. 1. " BLENDMODECOLORGREEN ,BlendModeColorGreen" hexmask.long.word 0x18 0.--15. 1. " BLENDMODECOLORRED ,BlendModeColorRed" line.long 0x1C "BLENDMODE2,Open GL and Open VG blending modes for color blue and alpha" hexmask.long.word 0x1C 16.--31. 1. " BLENDMODEALPHA ,BlendModeAlpha" hexmask.long.word 0x1C 1.--15. 1. " BLENDMODECOLORBLUE ,BlendModeColorBlue" rgroup.long 0x1420++0x07 line.long 0x00 "PRIM_CONTROL_WORD,Value of last received primary control word" line.long 0x04 "SEC_CONTROL_WORD,Value of last received secondary control word" sif (cpu()=="MB86R12") group.long 0x1428++0x3 line.long 0x00 "Debug,Debug" hexmask.long.word 0x00 10.--19. 1. " ALPHADEBUG ,Sets the multiplexers of the alpha datapath for debugging" hexmask.long.word 0x00 0.--9. 1. " COLORDEBUG ,Sets the multiplexers of the color datapath for debugging" endif tree.end tree "Lut 0" width 19. group.long 0x1800++0x03 line.long 0x00 "CONTROL,CLUT control register" bitfld.long 0x00 31. " SHD_UPD ,Shadow register update mode" "NORMAL,WRITE_THROUGH" eventfld.long 0x00 25. " READ_TIMEOUT ,Timeout detected when reading from the LUT" "0,1" textline " " eventfld.long 0x00 24. " WRITE_TIMEOUT ,Timeout detected when writing to the LUT" "0,1" bitfld.long 0x00 6.--9. " IDX_BITS ,Number of msb bits of the red color input used for the LUT index input" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 5. " R_EN ,Write enable for writing the red color LUT entry from the host" "Disabled,Enabled" bitfld.long 0x00 4. " G_EN ,Write enable for writing the green color LUT entry from the host" "Disable,Enabled" textline " " bitfld.long 0x00 3. " B_EN ,Write enable for writing the blue color LUT entry from the host" "Disabled,Enabled" bitfld.long 0x00 2. " COL_8BIT ,Color (red, green, blue) output bitwidth select" "Disabled,Enabled" textline " " bitfld.long 0x00 0.--1. " MODE ,Operation mode for color lookup table" "NEUTRAL,LUT,INDEX_10BIT,INDEX_RGBA" rgroup.long 0x1804++0x03 line.long 0x00 "LAST_CONTROL_WORD,Value of last received control word, for debugging" group.long 0x1C00++0x3 line.long 0x00 "LUT,LUT" button "LUT" "d (ad:0x38C00000+0x1C00)--(ad:0x38C00000+0x1FFF) /long" tree.end tree "Matrix 0" group.long 0x2000++0x1B line.long 0x00 "CONTROL,Color Matrix control register" bitfld.long 0x00 31. " SHD_UPD ,Shadow register update mode" "NORMAL,WRITE_THROUGH" bitfld.long 0x00 0.--1. " MODE ,Operation mode for color matrix" "NEUTRAL,MATRIX,PREMUL," line.long 0x04 "RED0,Matrix values for calculation of the red output value" hexmask.long.word 0x04 16.--26. 1. " A12 ,Value for Green input" hexmask.long.word 0x04 0.--10. 1. " A11 ,Value for Red input" line.long 0x08 "RED1,Matrix values for calculation of the red output value" hexmask.long.word 0x08 16.--26. 1. " C1 ,Red output Offset" hexmask.long.word 0x08 0.--10. 1. " A13 ,Value for Blue input" line.long 0x0C "GREEN0,Matrix values for calculation of the green output value" hexmask.long.word 0x0C 16.--26. 1. " A22 ,Value for Green input" hexmask.long.word 0x0C 0.--10. 1. " A21 ,Value for Red input" line.long 0x10 "GREEN1,Matrix values for calculation of the green output value" hexmask.long.word 0x10 16.--26. 1. " C2 ,Green output Offset" hexmask.long.word 0x10 0.--10. 1. " A23 ,Value for Blue input" line.long 0x14 "BLUE0,Matrix values for calculation of the blue output value" hexmask.long.word 0x14 16.--26. 1. " A32 ,Value for Green input" hexmask.long.word 0x14 0.--10. 1. " A31 ,Value for Red input" line.long 0x18 "BLUE1,Matrix values for calculation of the blue output value" hexmask.long.word 0x18 16.--26. 1. " C3 ,Blue output Offset" hexmask.long.word 0x18 0.--10. 1. " A33 ,Value for Blue input" rgroup.long 0x201C++0x03 line.long 0x00 "LAST_CONTROL_WORD,Value of last received control word, for debugging" tree.end tree "Pixelbus" width 18. group.long 0x2800++0x1F line.long 0x00 "FETCH0_CFG,Pixelbus configuration for unit fetch0" bitfld.long 0x00 26. " FETCH0_SHDW ,Control for shadow reload flag generation of fetch0 module" "Disabled,Store0" line.long 0x04 "FETCH1_CFG,Pixelbus configuration for unit fetch1" bitfld.long 0x04 26. " FETCH1_SHDW ,Control for shadow reload flag generation of fetch1 module" "Disabled,Store0" line.long 0x08 "FETCH2_CFG,Pixelbus configuration for unit fetch2" bitfld.long 0x08 26. " FETCH2_SHDW ,Control for shadow reload flag generation of fetch2 module" "Disabled,Store0" line.long 0x0C "STORE0_CFG,Pixelbus configuration for unit store0" bitfld.long 0x0C 26. " STORE0_SHDW ,Shadow control for this register" "Disabled,Store0" bitfld.long 0x0C 0.--3. " STORE0_SRC_SEL ,Selection of the source for the src input of the store0 module" "Disabled,,,fetch2,,,blitblend0,lut0,matrix0,,,,,,," line.long 0x10 "ROP0_CFG,Pixelbus configuration for unit rop0" bitfld.long 0x10 26. " ROP0_SHDW ,Shadow control for this register" "Disabled,Store0" bitfld.long 0x10 24.--25. " ROP0_CLKEN ,Enable of rop0 clock" "Disabled,Automatic,,Full" textline " " bitfld.long 0x10 16.--19. " ROP0_TERT_SEL ,Selection of the source for the tert input of the rop0 module" "Disabled,,,Fetch2,,,,Lut0,,,,,,,," bitfld.long 0x10 8.--11. " ROP0_SEC_SEL ,Selection of the source for the sec input of the rop0 module" "Disabled,,Fetch1,,,,,,,,,,,,," textline " " bitfld.long 0x10 0.--3. " ROP0_PRIM_SEL ,Selection of the source for the prim input of the rop0 module" "Disabled,,,Fetch2,,,,Lut0,,,,,,,," line.long 0x14 "BLITBLEND0_CFG,Pixelbus configuration for unit blitblend0" bitfld.long 0x14 26. " BLITBLEND0_SHDW ,Shadow control for this register" "Disabled,Store0" bitfld.long 0x14 24.--25. " BLITBLEND0_CLKEN ,Enable of blitblend0 clock" "Disabled,Automatic,,Full" textline " " bitfld.long 0x14 8.--11. " BLITBLEND0_SEC_SEL ,Selection of the source for the sec input of the blitblend0 module" "Disabled,,,Fetch2,,,,Lut0,,,,,,,," bitfld.long 0x14 0.--3. " BLITBLEND0_PRIM_SEL ,Selection of the source for the prim input of the blitblend0 module" "Disabled,,,,,,,Matrix0,,,,,,,," line.long 0x18 "LUT0_CFG,Pixelbus configuration for unit lut0" bitfld.long 0x18 26. " LUT0_SHDW ,Shadow control for this register" "Disabled,Store0" bitfld.long 0x18 24.--25. " LUT0_CLKEN ,Enable of lut0 clock" "Disabled,Automatic,,Full" textline " " bitfld.long 0x18 0.--3. " LUT0_SRC_SEL ,Selection of the source for the src input of the lut0 module" "Disabled,Fetch0,,,,,,,,,,,,,," line.long 0x1C "MATRIX0_CFG,Pixelbus configuration for unit matrix0" bitfld.long 0x1C 26. " MATRIX0_SHDW ,Shadow control for this register" "Disabled,Store0" bitfld.long 0x1C 24.--25. " MATRIX0_CLKEN ,Enable of matrix0 clock" "Disabled,Automatic,,Full" textline " " bitfld.long 0x1C 0.--3. " MATRIX0_SRC_SEL ,Selection of the source for the src input of the matrix0 module" "Disabled,,,,,Rop0,,,,,,,,,," group.long 0x2824++0x03 line.long 0x00 "STORE0_SYNC,Pixel engine synchronization" bitfld.long 0x00 4. " STORE0_STORE0_FRAME_END ,Detection mode of frame end for store0 pipeline" "PIXENG_SYNC,STORE0" bitfld.long 0x00 3. " STORE0_MST_EN ,Enable bits for master pipelines" "Off,Store0" textline " " bitfld.long 0x00 2. " STORE0_SLV_EN ,Enable bits for slave pipelines" "Off,Store0" bitfld.long 0x00 1. " STORE0_SYNC_RESET_N ,Software reset of synchronization state machine" "Reset,Active" textline " " eventfld.long 0x00 0. " STORE0_START ,Start synchronization with store0 pixel engine synchronizer" "0,1" rgroup.long 0x2828++0x03 line.long 0x00 "STORE0_SYNC_STAT,Pixel engine synchronization status" bitfld.long 0x00 1.--2. " STORE0_KICK_CNT_STORE0 ,State of store0 pipeline" "EMPTY,RUNNING,RUNNING_RETRIGGERED," bitfld.long 0x00 0. " STORE0_SYNC_BUSY ,Store0 pixel engine synchronizer busy" "0,1" group.long 0x282C++0x07 line.long 0x00 "STORE0_CLK,Store0 clock throttling" hexmask.long.byte 0x00 0.--7. 1. " STORE0_DIV ,Store0 clock dividing factor" line.long 0x04 "PIXENG_STS,Status collected from all interrupt signals" eventfld.long 0x04 5. " BLITBLEND0_STS0 ,Status bits for the blitblend0 interrupt number 0 the corresponding interrupt set this flag" "Not clear,Clear" eventfld.long 0x04 4. " ROP0_STS0 ,Status bits for the rop0 interrupt number 0 the corresponding interrupt set this flag" "Not clear,Clear" textline " " eventfld.long 0x04 3. " STORE0_STS2 ,Status bits for the store0 interrupt number2 the corresponding interrupt set this flag" "Not clear,Clear" eventfld.long 0x04 2. " STORE0_STS1 ,Status bits for the store0 interrupt number1 the corresponding interrupt set this flag" "Not clear,Clear" textline " " eventfld.long 0x04 1. " STORE0_STS0 ,Status bits for the store0 interrupt number0 the corresponding interrupt set this flag" "Not clear,Clear" eventfld.long 0x04 0. " STORE0_SYNC_STS ,Status bits for the store0 synchronizer interrupt the corresponding interrupt set this flag" "Not clear,Clear" tree.end width 0xb tree.end tree "CMDSEQ 0 (Command Sequencer)" base ad:0x38E00000 width 18. sif (cpu()=="MB86R24") group.long 0x00++0x03 line.long 0x00 "HIF,Command Input Buffer" else group.long 0x00++0x03 line.long 0x00 "HIF,Command Input Buffer" button "COMMANDFIFO" "d (ad:0x38E00000+0x0000)--(ad:0x38E00000+0x00FF) /long" endif rgroup.long 0x100++0x03 line.long 0x00 "STATUS,Status Register" bitfld.long 0x00 31. " ERROR ,Execution stopped after receiving an illegal instruction" "No error,Error" bitfld.long 0x00 30. " IDLE ,Command sequencer is in IDLE state" "Busy,Idle" bitfld.long 0x00 29. " WATCHDOG ,Watchdog expired" "Not expired,Expired" bitfld.long 0x00 26. " FIFOWMSTATE ,Watermark state" "0,1" textline " " bitfld.long 0x00 25. " FIFOFULL ,Command FIFO full flag" "Not full,Full" bitfld.long 0x00 24. " FIFOEMPTY ,Command FIFO empty flag" "Not empty,Empty" hexmask.long.tbyte 0x00 0.--16. 1. " FIFOSPACE ,The available space in the command FIFO in bytes" group.long 0x104++0x0F line.long 0x00 "CONTROL,Control Register" eventfld.long 0x00 31. " CLEAR ,Clear the command buffer" "Not cleared,Cleared" line.long 0x04 "BUFFERADDRESS,Command Buffer Address Register" hexmask.long 0x04 2.--31. 0x04 " ADDR ,Command buffer base address" sif (cpu()=="MB86R24") bitfld.long 0x04 0. " LOCAL ,Select local address space" "0,1" endif line.long 0x08 "BUFFERSIZE,Command Buffer Size Register" hexmask.long.word 0x08 0.--15. 1. " SIZE ,Size of command buffer in dwords" line.long 0x0C "WATERMARKCONTROL,Watermark Control Register" hexmask.long.word 0x0C 16.--31. 1. " HIGHWM ,High watermark" hexmask.long.word 0x0C 0.--15. 1. " LOWWM ,Low watermark" width 0x0B tree.end tree "CMDSEQ 1 (Command Sequencer)" base ad:0x38F00000 width 18. sif (cpu()=="MB86R24") group.long 0x00++0x03 line.long 0x00 "HIF,Command Input Buffer" else group.long 0x00++0x03 line.long 0x00 "HIF,Command Input Buffer" button "COMMANDFIFO" "d (ad:0x38F00000+0x0000)--(ad:0x38F00000+0x00FF) /long" endif rgroup.long 0x100++0x03 line.long 0x00 "STATUS,Status Register" bitfld.long 0x00 31. " ERROR ,Execution stopped after receiving an illegal instruction" "No error,Error" bitfld.long 0x00 30. " IDLE ,Command sequencer is in IDLE state" "Busy,Idle" bitfld.long 0x00 29. " WATCHDOG ,Watchdog expired" "Not expired,Expired" bitfld.long 0x00 26. " FIFOWMSTATE ,Watermark state" "0,1" textline " " bitfld.long 0x00 25. " FIFOFULL ,Command FIFO full flag" "Not full,Full" bitfld.long 0x00 24. " FIFOEMPTY ,Command FIFO empty flag" "Not empty,Empty" hexmask.long.tbyte 0x00 0.--16. 1. " FIFOSPACE ,The available space in the command FIFO in bytes" group.long 0x104++0x0F line.long 0x00 "CONTROL,Control Register" eventfld.long 0x00 31. " CLEAR ,Clear the command buffer" "Not cleared,Cleared" line.long 0x04 "BUFFERADDRESS,Command Buffer Address Register" hexmask.long 0x04 2.--31. 0x04 " ADDR ,Command buffer base address" sif (cpu()=="MB86R24") bitfld.long 0x04 0. " LOCAL ,Select local address space" "0,1" endif line.long 0x08 "BUFFERSIZE,Command Buffer Size Register" hexmask.long.word 0x08 0.--15. 1. " SIZE ,Size of command buffer in dwords" line.long 0x0C "WATERMARKCONTROL,Watermark Control Register" hexmask.long.word 0x0C 16.--31. 1. " HIGHWM ,High watermark" hexmask.long.word 0x0C 0.--15. 1. " LOWWM ,Low watermark" width 0x0B tree.end tree.end tree "I2S Serial audio interface" tree "I2S_0" base ad:0x04E00000 width 13. hgroup.long 0x00++0x03 hide.long 0x00 "RXFDAT,Reception FIFO Data Register" in wgroup.long 0x04++0x03 line.long 0x00 "TXFDAT,Transmission FIFO Data Register" if ((per.l(ad:0x04E00000+0x18))&0x01)==0x00 group.long 0x08++0x03 line.long 0x00 "CNTREG,Control Register" bitfld.long 0x00 26.--31. " CKRT ,Sets output clock frequency dividing ratio at master operation" "Bypassed,1/2,1/4,1/6,1/8,1/10,1/12,1/14,1/16,1/18,1/20,1/22,1/24,1/26,1/30,1/34,1/36,1/38,1/40,1/42,1/44,1/46,1/48,1/50,1/52,1/54,1/56,1/58,1/60,1/62,1/64,1/66,1/68,1/70,1/72,1/74,1/76,1/78,1/80,1/82,1/84,1/86,1/88,1/90,1/92,1/94,1/96,1/98,1/100,1/102,1/104,1/106,1/108,1/110,1/112,1/114,1/116,1/118,1/120,1/122,1/124,1/126,1/128,1/130" hexmask.long.word 0x00 16.--25. 1. " OVHD ,Frame rate is able to be adjusted by inserting OVHD bit following to valid data of the frame" textline " " bitfld.long 0x00 14. " MSKB ,Serial output data of invalid transmission frame" "Not set,Set" bitfld.long 0x00 13. " MSMD ,Master/Slave mode" "Slave,Master" textline " " bitfld.long 0x00 12. " SBFN ,Sub frame construction of the frame" "1 frame,2 frame" bitfld.long 0x00 11. " RHLL ,Handling of words in the FIFO" "1 word,2 word" textline " " bitfld.long 0x00 10. " ECKM ,Clock frequency division for master mode" "Internal clock,External clock" bitfld.long 0x00 9. " BEXT ,Extension mode" "Extended by 0,Extended by sign bit" textline " " bitfld.long 0x00 8. " FRUN ,Output mode of frame synchronous signal" "Burst mode,Free-running mode" bitfld.long 0x00 7. " MLSB ,Word bit's shift order" "MSB,LSB" textline " " bitfld.long 0x00 6. " TXDIS ,Transmitting function" "Enabled,Disabled" bitfld.long 0x00 5. " RXDIS ,Receiving function" "Enabled,Disabled" textline " " bitfld.long 0x00 4. " SMPL ,Sampling point of reception data" "Center,End" bitfld.long 0x00 3. " CPOL ,I2S_SCK polarity which drives/samples serial data" "Rising/Falling edge,Falling/Rising edge" textline " " bitfld.long 0x00 2. " FSPH ,Phase is specified to I2S_WS frame data" "1 clock before,Same time" bitfld.long 0x00 1. " FSLN ,Pulse width of I2S_WS" "1 bit,1 channel" textline " " bitfld.long 0x00 0. " FSPL ,Polarity of I2S_WS pin" "0 at idle,1 at idle" else rgroup.long 0x08++0x03 line.long 0x00 "CNTREG,Control Register" bitfld.long 0x00 26.--31. " CKRT ,Sets output clock frequency dividing ratio at master operation" "Bypassed,1/2,1/4,1/6,1/8,1/10,1/12,1/14,1/16,1/18,1/20,1/22,1/24,1/26,1/30,1/34,1/36,1/38,1/40,1/42,1/44,1/46,1/48,1/50,1/52,1/54,1/56,1/58,1/60,1/62,1/64,1/66,1/68,1/70,1/72,1/74,1/76,1/78,1/80,1/82,1/84,1/86,1/88,1/90,1/92,1/94,1/96,1/98,1/100,1/102,1/104,1/106,1/108,1/110,1/112,1/114,1/116,1/118,1/120,1/122,1/124,1/126,1/128,1/130" hexmask.long.word 0x00 16.--25. 1. " OVHD ,Frame rate is able to be adjusted by inserting OVHD bit following to valid data of the frame" textline " " bitfld.long 0x00 14. " MSKB ,Serial output data of invalid transmission frame" "Not set,Set" bitfld.long 0x00 13. " MSMD ,Master/Slave mode" "Slave,Master" textline " " bitfld.long 0x00 12. " SBFN ,Sub frame construction of the frame" "1 frame,2 frame" bitfld.long 0x00 11. " RHLL ,Handling of words in the FIFO" "1 word,2 word" textline " " bitfld.long 0x00 10. " ECKM ,Clock frequency division for master mode" "Internal clock,External clock" bitfld.long 0x00 9. " BEXT ,Extension mode" "Extended by 0,Extended by sign bit" textline " " bitfld.long 0x00 8. " FRUN ,Output mode of frame synchronous signal" "Burst mode,Free-running mode" bitfld.long 0x00 7. " MLSB ,Word bit's shift order" "MSB,LSB" textline " " bitfld.long 0x00 6. " TXDIS ,Transmitting function" "Enabled,Disabled" bitfld.long 0x00 5. " RXDIS ,Receiving function" "Enabled,Disabled" textline " " bitfld.long 0x00 4. " SMPL ,Sampling point of reception data" "Center,End" bitfld.long 0x00 3. " CPOL ,I2S_SCK polarity which drives/samples serial data" "Rising/Falling edge,Falling/Rising edge" textline " " bitfld.long 0x00 2. " FSPH ,Phase is specified to I2S_WS frame data" "1 clock before,Same time" bitfld.long 0x00 1. " FSLN ,Pulse width of I2S_WS" "1 bit,1 channel" textline " " bitfld.long 0x00 0. " FSPL ,Polarity of I2S_WS pin" "0 at idle,1 at idle" endif width 13. textline " " if ((per.l(ad:0x04E00000+0x08))&0x1000)==0x1000 group.long 0x0C++0x03 line.long 0x00 "MCR0REG,Channel Control Register 0" bitfld.long 0x00 26.--30. " S1CHN ,Number of channel of sub frame 1" "1 channel,2 channel,3 channel,4 channel,5 channel,6 channel,7 channel,8 channel,9 channel,10 channel,11 channel,12 channel,13 channel,14 channel,15 channel,16 channel,17 channel,18 channel,19 channel,20 channel,21 channel,22 channel,23 channel,24 channel,25 channel,26 channel,27 channel,28 channel,29 channel,30 channel,31 channel,32 channel" bitfld.long 0x00 21.--25. " S1CHL ,Channel length of the channel constructing sub frame 1" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" bitfld.long 0x00 16.--20. " S1WDL ,Word length of the channel constructing sub frame 1" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" textline " " bitfld.long 0x00 10.--14. " S0CHN ,Number of channel of sub frame 0 is set up to 32 channels" "1 channel,2 channel,3 channel,4 channel,5 channel,6 channel,7 channel,8 channel,9 channel,10 channel,11 channel,12 channel,13 channel,14 channel,15 channel,16 channel,17 channel,18 channel,19 channel,20 channel,21 channel,22 channel,23 channel,24 channel,25 channel,26 channel,27 channel,28 channel,29 channel,30 channel,31 channel,32 channel" bitfld.long 0x00 5.--9. " S0CHL ,Channel length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" bitfld.long 0x00 0.--4. " S0WDL ,Word length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" else group.long 0x0C++0x03 line.long 0x00 "MCR0REG,Channel Control Register 0" bitfld.long 0x00 10.--14. " S0CHN ,Number of channel of sub frame 0 is set up to 32 channels" "1 channel,2 channel,3 channel,4 channel,5 channel,6 channel,7 channel,8 channel,9 channel,10 channel,11 channel,12 channel,13 channel,14 channel,15 channel,16 channel,17 channel,18 channel,19 channel,20 channel,21 channel,22 channel,23 channel,24 channel,25 channel,26 channel,27 channel,28 channel,29 channel,30 channel,31 channel,32 channel" bitfld.long 0x00 5.--9. " S0CHL ,Channel length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" bitfld.long 0x00 0.--4. " S0WDL ,Word length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" endif group.long 0x10++0x03 line.long 0x00 "MCR1REG,Channel Control Register 1" bitfld.long 0x00 31. " S0CH31 ,The S0CH31 bit controls the 31 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 30. " S0CH30 ,The S0CH30 bit controls the 30 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 29. " S0CH29 ,The S0CH29 bit controls the 29 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 28. " S0CH28 ,The S0CH28 bit controls the 28 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 27. " S0CH27 ,The S0CH27 bit controls the 27 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 26. " S0CH26 ,The S0CH26 bit controls the 26 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 25. " S0CH25 ,The S0CH25 bit controls the 25 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 24. " S0CH24 ,The S0CH24 bit controls the 24 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 23. " S0CH23 ,The S0CH23 bit controls the 23 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 22. " S0CH22 ,The S0CH22 bit controls the 22 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 21. " S0CH21 ,The S0CH21 bit controls the 21 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 20. " S0CH20 ,The S0CH20 bit controls the 20 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " S0CH19 ,The S0CH19 bit controls the 19 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 18. " S0CH18 ,The S0CH18 bit controls the 18 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 17. " S0CH17 ,The S0CH17 bit controls the 17 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 16. " S0CH16 ,The S0CH16 bit controls the 16 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 15. " S0CH15 ,The S0CH15 bit controls the 15 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 14. " S0CH14 ,The S0CH14 bit controls the 14 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 13. " S0CH13 ,The S0CH13 bit controls the 13 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 12. " S0CH12 ,The S0CH12 bit controls the 12 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " S0CH11 ,The S0CH11 bit controls the 11 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 10. " S0CH10 ,The S0CH10 bit controls the 10 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 9. " S0CH9 ,The S0CH9 bit controls the 9 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 8. " S0CH8 ,The S0CH8 bit controls the 8 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " S0CH7 ,The S0CH7 bit controls the 7 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 6. " S0CH6 ,The S0CH6 bit controls the 6 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 5. " S0CH5 ,The S0CH5 bit controls the 5 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 4. " S0CH4 ,The S0CH4 bit controls the 4 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " S0CH3 ,The S0CH3 bit controls the 3 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 2. " S0CH2 ,The S0CH2 bit controls the 2 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 1. " S0CH1 ,The S0CH1 bit controls the 1 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 0. " S0CH0 ,The S0CH0 bit controls the 0 channel of sub frame 0" "Disabled,Enabled" if (((per.l(ad:0x04E00000+0x08))&0x1000)==0x1000) group.long 0x14++0x03 line.long 0x00 "MCR2REG,Channel Control Register 2" bitfld.long 0x00 31. " S1CH31 ,The S1CH31 bit controls the 31 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 30. " S1CH30 ,The S1CH30 bit controls the 30 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 29. " S1CH29 ,The S1CH29 bit controls the 29 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 28. " S1CH28 ,The S1CH28 bit controls the 28 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 27. " S1CH27 ,The S1CH27 bit controls the 27 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 26. " S1CH26 ,The S1CH26 bit controls the 26 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 25. " S1CH25 ,The S1CH25 bit controls the 25 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 24. " S1CH24 ,The S1CH24 bit controls the 24 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 23. " S1CH23 ,The S1CH23 bit controls the 23 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 22. " S1CH22 ,The S1CH22 bit controls the 22 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 21. " S1CH21 ,The S1CH21 bit controls the 21 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 20. " S1CH20 ,The S1CH20 bit controls the 20 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " S1CH19 ,The S1CH19 bit controls the 19 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 18. " S1CH18 ,The S1CH18 bit controls the 18 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 17. " S1CH17 ,The S1CH17 bit controls the 17 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 16. " S1CH16 ,The S1CH16 bit controls the 16 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 15. " S1CH15 ,The S1CH15 bit controls the 15 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 14. " S1CH14 ,The S1CH14 bit controls the 14 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 13. " S1CH13 ,The S1CH13 bit controls the 13 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 12. " S1CH12 ,The S1CH12 bit controls the 12 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " S1CH11 ,The S1CH11 bit controls the 11 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 10. " S1CH10 ,The S1CH10 bit controls the 10 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 9. " S1CH9 ,The S1CH9 bit controls the 9 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 8. " S1CH8 ,The S1CH8 bit controls the 8 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " S1CH7 ,The S1CH7 bit controls the 7 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 6. " S1CH6 ,The S1CH6 bit controls the 6 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 5. " S1CH5 ,The S1CH5 bit controls the 5 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 4. " S1CH4 ,The S1CH4 bit controls the 4 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " S1CH3 ,The S1CH3 bit controls the 3 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 2. " S1CH2 ,The S1CH2 bit controls the 2 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 1. " S1CH1 ,The S1CH1 bit controls the 1 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 0. " S1CH0 ,The S1CH0 bit controls the 0 channel of sub frame 1" "Disabled,Enabled" textline " " else hgroup.long 0x14++0x03 hide.long 0x00 "MCR2REG,Channel Control Register 2" endif group.long 0x18++0x13 line.long 0x00 "OPRREG,Operation Control Register" bitfld.long 0x00 24. " RXENB ,Enable functions of receiving operation" "Disabled,Enabled" bitfld.long 0x00 16. " TXENB ,Enable functions of transmitting operation" "Disabled,Enabled" bitfld.long 0x00 0. " START ,I2S operation enable" "Disabled,Enabled" line.long 0x04 "SRST,Software Reset Register" bitfld.long 0x04 0. " SRST ,Software reset" "No reset,Reset" line.long 0x08 "INTCNT,Interrupt Control Register" bitfld.long 0x08 30. " TXUD1M ,Transmission FIFO underflow interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 29. " TBERM ,Interrupt mask bit of block size error of transmission channel" "Not masked,Masked" textline " " bitfld.long 0x08 28. " FERRM ,Frame error interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 27. " TXUD0M ,Transmission FIFO underflow interrupt mask bit" "Not masked,Masked" textline " " bitfld.long 0x08 26. " TXOVM ,Transmission FIFO overflow interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 25. " TXFDM ,DMA request mask register bit" "Request,Not request" textline " " bitfld.long 0x08 24. " TXFIM ,Transmission FIFO interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 21. " RBERM ,Interrupt mask bit of reception channel block size error" "Not masked,Masked" textline " " bitfld.long 0x08 20. " RXUDM ,Reception underflow interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 19. " RXOVM ,Interrupt mask bit of reception FIFO overflow" "Not masked,Masked" textline " " bitfld.long 0x08 18. " EOPM ,Interrupt mask bit by EOPI of STATUS register" "Not masked,Masked" bitfld.long 0x08 17. " RXFDM ,Reception DMA request mask bit" "Request,Not request" textline " " bitfld.long 0x08 16. " RXFIM ,Reception FIFO interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 8.--11. " TFTH ,Threshold value of transmission FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x08 4.--5. " RPTMR ,Packet reception completion timer setting bit" "0,54000 AHB clock cycles,108000 AHB clock cycles,216000 AHB clock cycles" bitfld.long 0x08 0.--3. " RFTH ,Threshold value of reception FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x0C "STATUS,STATUS Register" rbitfld.long 0x0C 31. " TBERR ,Block size of DMA transmission channel" "Disabled,Enabled" rbitfld.long 0x0C 30. " RBERR ,Block size of DMA reception channel" "Disabled,Enabled" textline " " eventfld.long 0x0C 29. " FERR ,Occurrence of frame error" "Disabled,Enabled" eventfld.long 0x0C 28. " TXUDR1 ,Transmission FIFO underflows at the top of frame" "Disabled,Enabled" textline " " eventfld.long 0x0C 27. " TXUDR0 ,Transmission FIFO underflows during frame transmission" "Disabled,Enabled" eventfld.long 0x0C 26. " TXOVR ,Transmission FIFO overflows" "Disabled,Enabled" textline " " eventfld.long 0x0C 25. " RXUDR ,Reception FIFO underflows" "Disabled,Enabled" eventfld.long 0x0C 24. " RXOVR ,Reception FIFO overflows" "Disabled,Enabled" textline " " eventfld.long 0x0C 19. " EOPI ,Interrupt flag containing reception timer" "Disabled,Enabled" rbitfld.long 0x0C 18. " BSY ,Serial transmission control part" "Idle,Busy" textline " " rbitfld.long 0x0C 17. " TXFI ,Number of empty slot of reception FIFO" "Disabled,Enabled" rbitfld.long 0x0C 16. " RXFI ,Number of reception FIFO data" "Disabled,Enabled" textline " " rbitfld.long 0x0C 8.--13. " TXNUM ,The number of data in transmission FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" rbitfld.long 0x0C 0.--5. " RXNUM ,The number of data in reception FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x10 "DMAACT,DMA Start-Up Register" sif (cpu()=="MB86R12")||(cpu()=="MB86R24") bitfld.long 0x10 24. " TL1E0 ,TXDREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " elif (cpu()=="MB86R11") rbitfld.long 0x10 24. " TL1E0 ,TXDREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " endif bitfld.long 0x10 16. " TDMACT ,Transmission channel of DMAC" "Not active,Active" textline " " sif (cpu()=="MB86R12")||(cpu()=="MB86R24") bitfld.long 0x10 8. " RL1E0 ,RXREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " elif (cpu()=="MB86R11") rbitfld.long 0x10 8. " RL1E0 ,RXREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " endif bitfld.long 0x10 0. " RDMACT ,The reception channel of DMAC" "Not active,Active" width 0x0B tree.end tree "I2S_1" base ad:0x04E10000 width 13. hgroup.long 0x00++0x03 hide.long 0x00 "RXFDAT,Reception FIFO Data Register" in wgroup.long 0x04++0x03 line.long 0x00 "TXFDAT,Transmission FIFO Data Register" if ((per.l(ad:0x04E10000+0x18))&0x01)==0x00 group.long 0x08++0x03 line.long 0x00 "CNTREG,Control Register" bitfld.long 0x00 26.--31. " CKRT ,Sets output clock frequency dividing ratio at master operation" "Bypassed,1/2,1/4,1/6,1/8,1/10,1/12,1/14,1/16,1/18,1/20,1/22,1/24,1/26,1/30,1/34,1/36,1/38,1/40,1/42,1/44,1/46,1/48,1/50,1/52,1/54,1/56,1/58,1/60,1/62,1/64,1/66,1/68,1/70,1/72,1/74,1/76,1/78,1/80,1/82,1/84,1/86,1/88,1/90,1/92,1/94,1/96,1/98,1/100,1/102,1/104,1/106,1/108,1/110,1/112,1/114,1/116,1/118,1/120,1/122,1/124,1/126,1/128,1/130" hexmask.long.word 0x00 16.--25. 1. " OVHD ,Frame rate is able to be adjusted by inserting OVHD bit following to valid data of the frame" textline " " bitfld.long 0x00 14. " MSKB ,Serial output data of invalid transmission frame" "Not set,Set" bitfld.long 0x00 13. " MSMD ,Master/Slave mode" "Slave,Master" textline " " bitfld.long 0x00 12. " SBFN ,Sub frame construction of the frame" "1 frame,2 frame" bitfld.long 0x00 11. " RHLL ,Handling of words in the FIFO" "1 word,2 word" textline " " bitfld.long 0x00 10. " ECKM ,Clock frequency division for master mode" "Internal clock,External clock" bitfld.long 0x00 9. " BEXT ,Extension mode" "Extended by 0,Extended by sign bit" textline " " bitfld.long 0x00 8. " FRUN ,Output mode of frame synchronous signal" "Burst mode,Free-running mode" bitfld.long 0x00 7. " MLSB ,Word bit's shift order" "MSB,LSB" textline " " bitfld.long 0x00 6. " TXDIS ,Transmitting function" "Enabled,Disabled" bitfld.long 0x00 5. " RXDIS ,Receiving function" "Enabled,Disabled" textline " " bitfld.long 0x00 4. " SMPL ,Sampling point of reception data" "Center,End" bitfld.long 0x00 3. " CPOL ,I2S_SCK polarity which drives/samples serial data" "Rising/Falling edge,Falling/Rising edge" textline " " bitfld.long 0x00 2. " FSPH ,Phase is specified to I2S_WS frame data" "1 clock before,Same time" bitfld.long 0x00 1. " FSLN ,Pulse width of I2S_WS" "1 bit,1 channel" textline " " bitfld.long 0x00 0. " FSPL ,Polarity of I2S_WS pin" "0 at idle,1 at idle" else rgroup.long 0x08++0x03 line.long 0x00 "CNTREG,Control Register" bitfld.long 0x00 26.--31. " CKRT ,Sets output clock frequency dividing ratio at master operation" "Bypassed,1/2,1/4,1/6,1/8,1/10,1/12,1/14,1/16,1/18,1/20,1/22,1/24,1/26,1/30,1/34,1/36,1/38,1/40,1/42,1/44,1/46,1/48,1/50,1/52,1/54,1/56,1/58,1/60,1/62,1/64,1/66,1/68,1/70,1/72,1/74,1/76,1/78,1/80,1/82,1/84,1/86,1/88,1/90,1/92,1/94,1/96,1/98,1/100,1/102,1/104,1/106,1/108,1/110,1/112,1/114,1/116,1/118,1/120,1/122,1/124,1/126,1/128,1/130" hexmask.long.word 0x00 16.--25. 1. " OVHD ,Frame rate is able to be adjusted by inserting OVHD bit following to valid data of the frame" textline " " bitfld.long 0x00 14. " MSKB ,Serial output data of invalid transmission frame" "Not set,Set" bitfld.long 0x00 13. " MSMD ,Master/Slave mode" "Slave,Master" textline " " bitfld.long 0x00 12. " SBFN ,Sub frame construction of the frame" "1 frame,2 frame" bitfld.long 0x00 11. " RHLL ,Handling of words in the FIFO" "1 word,2 word" textline " " bitfld.long 0x00 10. " ECKM ,Clock frequency division for master mode" "Internal clock,External clock" bitfld.long 0x00 9. " BEXT ,Extension mode" "Extended by 0,Extended by sign bit" textline " " bitfld.long 0x00 8. " FRUN ,Output mode of frame synchronous signal" "Burst mode,Free-running mode" bitfld.long 0x00 7. " MLSB ,Word bit's shift order" "MSB,LSB" textline " " bitfld.long 0x00 6. " TXDIS ,Transmitting function" "Enabled,Disabled" bitfld.long 0x00 5. " RXDIS ,Receiving function" "Enabled,Disabled" textline " " bitfld.long 0x00 4. " SMPL ,Sampling point of reception data" "Center,End" bitfld.long 0x00 3. " CPOL ,I2S_SCK polarity which drives/samples serial data" "Rising/Falling edge,Falling/Rising edge" textline " " bitfld.long 0x00 2. " FSPH ,Phase is specified to I2S_WS frame data" "1 clock before,Same time" bitfld.long 0x00 1. " FSLN ,Pulse width of I2S_WS" "1 bit,1 channel" textline " " bitfld.long 0x00 0. " FSPL ,Polarity of I2S_WS pin" "0 at idle,1 at idle" endif width 13. textline " " if ((per.l(ad:0x04E10000+0x08))&0x1000)==0x1000 group.long 0x0C++0x03 line.long 0x00 "MCR0REG,Channel Control Register 0" bitfld.long 0x00 26.--30. " S1CHN ,Number of channel of sub frame 1" "1 channel,2 channel,3 channel,4 channel,5 channel,6 channel,7 channel,8 channel,9 channel,10 channel,11 channel,12 channel,13 channel,14 channel,15 channel,16 channel,17 channel,18 channel,19 channel,20 channel,21 channel,22 channel,23 channel,24 channel,25 channel,26 channel,27 channel,28 channel,29 channel,30 channel,31 channel,32 channel" bitfld.long 0x00 21.--25. " S1CHL ,Channel length of the channel constructing sub frame 1" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" bitfld.long 0x00 16.--20. " S1WDL ,Word length of the channel constructing sub frame 1" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" textline " " bitfld.long 0x00 10.--14. " S0CHN ,Number of channel of sub frame 0 is set up to 32 channels" "1 channel,2 channel,3 channel,4 channel,5 channel,6 channel,7 channel,8 channel,9 channel,10 channel,11 channel,12 channel,13 channel,14 channel,15 channel,16 channel,17 channel,18 channel,19 channel,20 channel,21 channel,22 channel,23 channel,24 channel,25 channel,26 channel,27 channel,28 channel,29 channel,30 channel,31 channel,32 channel" bitfld.long 0x00 5.--9. " S0CHL ,Channel length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" bitfld.long 0x00 0.--4. " S0WDL ,Word length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" else group.long 0x0C++0x03 line.long 0x00 "MCR0REG,Channel Control Register 0" bitfld.long 0x00 10.--14. " S0CHN ,Number of channel of sub frame 0 is set up to 32 channels" "1 channel,2 channel,3 channel,4 channel,5 channel,6 channel,7 channel,8 channel,9 channel,10 channel,11 channel,12 channel,13 channel,14 channel,15 channel,16 channel,17 channel,18 channel,19 channel,20 channel,21 channel,22 channel,23 channel,24 channel,25 channel,26 channel,27 channel,28 channel,29 channel,30 channel,31 channel,32 channel" bitfld.long 0x00 5.--9. " S0CHL ,Channel length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" bitfld.long 0x00 0.--4. " S0WDL ,Word length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" endif group.long 0x10++0x03 line.long 0x00 "MCR1REG,Channel Control Register 1" bitfld.long 0x00 31. " S0CH31 ,The S0CH31 bit controls the 31 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 30. " S0CH30 ,The S0CH30 bit controls the 30 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 29. " S0CH29 ,The S0CH29 bit controls the 29 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 28. " S0CH28 ,The S0CH28 bit controls the 28 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 27. " S0CH27 ,The S0CH27 bit controls the 27 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 26. " S0CH26 ,The S0CH26 bit controls the 26 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 25. " S0CH25 ,The S0CH25 bit controls the 25 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 24. " S0CH24 ,The S0CH24 bit controls the 24 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 23. " S0CH23 ,The S0CH23 bit controls the 23 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 22. " S0CH22 ,The S0CH22 bit controls the 22 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 21. " S0CH21 ,The S0CH21 bit controls the 21 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 20. " S0CH20 ,The S0CH20 bit controls the 20 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " S0CH19 ,The S0CH19 bit controls the 19 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 18. " S0CH18 ,The S0CH18 bit controls the 18 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 17. " S0CH17 ,The S0CH17 bit controls the 17 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 16. " S0CH16 ,The S0CH16 bit controls the 16 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 15. " S0CH15 ,The S0CH15 bit controls the 15 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 14. " S0CH14 ,The S0CH14 bit controls the 14 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 13. " S0CH13 ,The S0CH13 bit controls the 13 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 12. " S0CH12 ,The S0CH12 bit controls the 12 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " S0CH11 ,The S0CH11 bit controls the 11 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 10. " S0CH10 ,The S0CH10 bit controls the 10 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 9. " S0CH9 ,The S0CH9 bit controls the 9 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 8. " S0CH8 ,The S0CH8 bit controls the 8 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " S0CH7 ,The S0CH7 bit controls the 7 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 6. " S0CH6 ,The S0CH6 bit controls the 6 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 5. " S0CH5 ,The S0CH5 bit controls the 5 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 4. " S0CH4 ,The S0CH4 bit controls the 4 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " S0CH3 ,The S0CH3 bit controls the 3 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 2. " S0CH2 ,The S0CH2 bit controls the 2 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 1. " S0CH1 ,The S0CH1 bit controls the 1 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 0. " S0CH0 ,The S0CH0 bit controls the 0 channel of sub frame 0" "Disabled,Enabled" if (((per.l(ad:0x04E10000+0x08))&0x1000)==0x1000) group.long 0x14++0x03 line.long 0x00 "MCR2REG,Channel Control Register 2" bitfld.long 0x00 31. " S1CH31 ,The S1CH31 bit controls the 31 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 30. " S1CH30 ,The S1CH30 bit controls the 30 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 29. " S1CH29 ,The S1CH29 bit controls the 29 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 28. " S1CH28 ,The S1CH28 bit controls the 28 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 27. " S1CH27 ,The S1CH27 bit controls the 27 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 26. " S1CH26 ,The S1CH26 bit controls the 26 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 25. " S1CH25 ,The S1CH25 bit controls the 25 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 24. " S1CH24 ,The S1CH24 bit controls the 24 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 23. " S1CH23 ,The S1CH23 bit controls the 23 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 22. " S1CH22 ,The S1CH22 bit controls the 22 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 21. " S1CH21 ,The S1CH21 bit controls the 21 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 20. " S1CH20 ,The S1CH20 bit controls the 20 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " S1CH19 ,The S1CH19 bit controls the 19 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 18. " S1CH18 ,The S1CH18 bit controls the 18 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 17. " S1CH17 ,The S1CH17 bit controls the 17 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 16. " S1CH16 ,The S1CH16 bit controls the 16 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 15. " S1CH15 ,The S1CH15 bit controls the 15 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 14. " S1CH14 ,The S1CH14 bit controls the 14 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 13. " S1CH13 ,The S1CH13 bit controls the 13 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 12. " S1CH12 ,The S1CH12 bit controls the 12 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " S1CH11 ,The S1CH11 bit controls the 11 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 10. " S1CH10 ,The S1CH10 bit controls the 10 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 9. " S1CH9 ,The S1CH9 bit controls the 9 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 8. " S1CH8 ,The S1CH8 bit controls the 8 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " S1CH7 ,The S1CH7 bit controls the 7 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 6. " S1CH6 ,The S1CH6 bit controls the 6 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 5. " S1CH5 ,The S1CH5 bit controls the 5 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 4. " S1CH4 ,The S1CH4 bit controls the 4 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " S1CH3 ,The S1CH3 bit controls the 3 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 2. " S1CH2 ,The S1CH2 bit controls the 2 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 1. " S1CH1 ,The S1CH1 bit controls the 1 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 0. " S1CH0 ,The S1CH0 bit controls the 0 channel of sub frame 1" "Disabled,Enabled" textline " " else hgroup.long 0x14++0x03 hide.long 0x00 "MCR2REG,Channel Control Register 2" endif group.long 0x18++0x13 line.long 0x00 "OPRREG,Operation Control Register" bitfld.long 0x00 24. " RXENB ,Enable functions of receiving operation" "Disabled,Enabled" bitfld.long 0x00 16. " TXENB ,Enable functions of transmitting operation" "Disabled,Enabled" bitfld.long 0x00 0. " START ,I2S operation enable" "Disabled,Enabled" line.long 0x04 "SRST,Software Reset Register" bitfld.long 0x04 0. " SRST ,Software reset" "No reset,Reset" line.long 0x08 "INTCNT,Interrupt Control Register" bitfld.long 0x08 30. " TXUD1M ,Transmission FIFO underflow interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 29. " TBERM ,Interrupt mask bit of block size error of transmission channel" "Not masked,Masked" textline " " bitfld.long 0x08 28. " FERRM ,Frame error interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 27. " TXUD0M ,Transmission FIFO underflow interrupt mask bit" "Not masked,Masked" textline " " bitfld.long 0x08 26. " TXOVM ,Transmission FIFO overflow interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 25. " TXFDM ,DMA request mask register bit" "Request,Not request" textline " " bitfld.long 0x08 24. " TXFIM ,Transmission FIFO interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 21. " RBERM ,Interrupt mask bit of reception channel block size error" "Not masked,Masked" textline " " bitfld.long 0x08 20. " RXUDM ,Reception underflow interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 19. " RXOVM ,Interrupt mask bit of reception FIFO overflow" "Not masked,Masked" textline " " bitfld.long 0x08 18. " EOPM ,Interrupt mask bit by EOPI of STATUS register" "Not masked,Masked" bitfld.long 0x08 17. " RXFDM ,Reception DMA request mask bit" "Request,Not request" textline " " bitfld.long 0x08 16. " RXFIM ,Reception FIFO interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 8.--11. " TFTH ,Threshold value of transmission FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x08 4.--5. " RPTMR ,Packet reception completion timer setting bit" "0,54000 AHB clock cycles,108000 AHB clock cycles,216000 AHB clock cycles" bitfld.long 0x08 0.--3. " RFTH ,Threshold value of reception FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x0C "STATUS,STATUS Register" rbitfld.long 0x0C 31. " TBERR ,Block size of DMA transmission channel" "Disabled,Enabled" rbitfld.long 0x0C 30. " RBERR ,Block size of DMA reception channel" "Disabled,Enabled" textline " " eventfld.long 0x0C 29. " FERR ,Occurrence of frame error" "Disabled,Enabled" eventfld.long 0x0C 28. " TXUDR1 ,Transmission FIFO underflows at the top of frame" "Disabled,Enabled" textline " " eventfld.long 0x0C 27. " TXUDR0 ,Transmission FIFO underflows during frame transmission" "Disabled,Enabled" eventfld.long 0x0C 26. " TXOVR ,Transmission FIFO overflows" "Disabled,Enabled" textline " " eventfld.long 0x0C 25. " RXUDR ,Reception FIFO underflows" "Disabled,Enabled" eventfld.long 0x0C 24. " RXOVR ,Reception FIFO overflows" "Disabled,Enabled" textline " " eventfld.long 0x0C 19. " EOPI ,Interrupt flag containing reception timer" "Disabled,Enabled" rbitfld.long 0x0C 18. " BSY ,Serial transmission control part" "Idle,Busy" textline " " rbitfld.long 0x0C 17. " TXFI ,Number of empty slot of reception FIFO" "Disabled,Enabled" rbitfld.long 0x0C 16. " RXFI ,Number of reception FIFO data" "Disabled,Enabled" textline " " rbitfld.long 0x0C 8.--13. " TXNUM ,The number of data in transmission FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" rbitfld.long 0x0C 0.--5. " RXNUM ,The number of data in reception FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x10 "DMAACT,DMA Start-Up Register" sif (cpu()=="MB86R12")||(cpu()=="MB86R24") bitfld.long 0x10 24. " TL1E0 ,TXDREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " elif (cpu()=="MB86R11") rbitfld.long 0x10 24. " TL1E0 ,TXDREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " endif bitfld.long 0x10 16. " TDMACT ,Transmission channel of DMAC" "Not active,Active" textline " " sif (cpu()=="MB86R12")||(cpu()=="MB86R24") bitfld.long 0x10 8. " RL1E0 ,RXREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " elif (cpu()=="MB86R11") rbitfld.long 0x10 8. " RL1E0 ,RXREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " endif bitfld.long 0x10 0. " RDMACT ,The reception channel of DMAC" "Not active,Active" width 0x0B tree.end tree "I2S_2" base ad:0x04E20000 width 13. hgroup.long 0x00++0x03 hide.long 0x00 "RXFDAT,Reception FIFO Data Register" in wgroup.long 0x04++0x03 line.long 0x00 "TXFDAT,Transmission FIFO Data Register" if ((per.l(ad:0x04E20000+0x18))&0x01)==0x00 group.long 0x08++0x03 line.long 0x00 "CNTREG,Control Register" bitfld.long 0x00 26.--31. " CKRT ,Sets output clock frequency dividing ratio at master operation" "Bypassed,1/2,1/4,1/6,1/8,1/10,1/12,1/14,1/16,1/18,1/20,1/22,1/24,1/26,1/30,1/34,1/36,1/38,1/40,1/42,1/44,1/46,1/48,1/50,1/52,1/54,1/56,1/58,1/60,1/62,1/64,1/66,1/68,1/70,1/72,1/74,1/76,1/78,1/80,1/82,1/84,1/86,1/88,1/90,1/92,1/94,1/96,1/98,1/100,1/102,1/104,1/106,1/108,1/110,1/112,1/114,1/116,1/118,1/120,1/122,1/124,1/126,1/128,1/130" hexmask.long.word 0x00 16.--25. 1. " OVHD ,Frame rate is able to be adjusted by inserting OVHD bit following to valid data of the frame" textline " " bitfld.long 0x00 14. " MSKB ,Serial output data of invalid transmission frame" "Not set,Set" bitfld.long 0x00 13. " MSMD ,Master/Slave mode" "Slave,Master" textline " " bitfld.long 0x00 12. " SBFN ,Sub frame construction of the frame" "1 frame,2 frame" bitfld.long 0x00 11. " RHLL ,Handling of words in the FIFO" "1 word,2 word" textline " " bitfld.long 0x00 10. " ECKM ,Clock frequency division for master mode" "Internal clock,External clock" bitfld.long 0x00 9. " BEXT ,Extension mode" "Extended by 0,Extended by sign bit" textline " " bitfld.long 0x00 8. " FRUN ,Output mode of frame synchronous signal" "Burst mode,Free-running mode" bitfld.long 0x00 7. " MLSB ,Word bit's shift order" "MSB,LSB" textline " " bitfld.long 0x00 6. " TXDIS ,Transmitting function" "Enabled,Disabled" bitfld.long 0x00 5. " RXDIS ,Receiving function" "Enabled,Disabled" textline " " bitfld.long 0x00 4. " SMPL ,Sampling point of reception data" "Center,End" bitfld.long 0x00 3. " CPOL ,I2S_SCK polarity which drives/samples serial data" "Rising/Falling edge,Falling/Rising edge" textline " " bitfld.long 0x00 2. " FSPH ,Phase is specified to I2S_WS frame data" "1 clock before,Same time" bitfld.long 0x00 1. " FSLN ,Pulse width of I2S_WS" "1 bit,1 channel" textline " " bitfld.long 0x00 0. " FSPL ,Polarity of I2S_WS pin" "0 at idle,1 at idle" else rgroup.long 0x08++0x03 line.long 0x00 "CNTREG,Control Register" bitfld.long 0x00 26.--31. " CKRT ,Sets output clock frequency dividing ratio at master operation" "Bypassed,1/2,1/4,1/6,1/8,1/10,1/12,1/14,1/16,1/18,1/20,1/22,1/24,1/26,1/30,1/34,1/36,1/38,1/40,1/42,1/44,1/46,1/48,1/50,1/52,1/54,1/56,1/58,1/60,1/62,1/64,1/66,1/68,1/70,1/72,1/74,1/76,1/78,1/80,1/82,1/84,1/86,1/88,1/90,1/92,1/94,1/96,1/98,1/100,1/102,1/104,1/106,1/108,1/110,1/112,1/114,1/116,1/118,1/120,1/122,1/124,1/126,1/128,1/130" hexmask.long.word 0x00 16.--25. 1. " OVHD ,Frame rate is able to be adjusted by inserting OVHD bit following to valid data of the frame" textline " " bitfld.long 0x00 14. " MSKB ,Serial output data of invalid transmission frame" "Not set,Set" bitfld.long 0x00 13. " MSMD ,Master/Slave mode" "Slave,Master" textline " " bitfld.long 0x00 12. " SBFN ,Sub frame construction of the frame" "1 frame,2 frame" bitfld.long 0x00 11. " RHLL ,Handling of words in the FIFO" "1 word,2 word" textline " " bitfld.long 0x00 10. " ECKM ,Clock frequency division for master mode" "Internal clock,External clock" bitfld.long 0x00 9. " BEXT ,Extension mode" "Extended by 0,Extended by sign bit" textline " " bitfld.long 0x00 8. " FRUN ,Output mode of frame synchronous signal" "Burst mode,Free-running mode" bitfld.long 0x00 7. " MLSB ,Word bit's shift order" "MSB,LSB" textline " " bitfld.long 0x00 6. " TXDIS ,Transmitting function" "Enabled,Disabled" bitfld.long 0x00 5. " RXDIS ,Receiving function" "Enabled,Disabled" textline " " bitfld.long 0x00 4. " SMPL ,Sampling point of reception data" "Center,End" bitfld.long 0x00 3. " CPOL ,I2S_SCK polarity which drives/samples serial data" "Rising/Falling edge,Falling/Rising edge" textline " " bitfld.long 0x00 2. " FSPH ,Phase is specified to I2S_WS frame data" "1 clock before,Same time" bitfld.long 0x00 1. " FSLN ,Pulse width of I2S_WS" "1 bit,1 channel" textline " " bitfld.long 0x00 0. " FSPL ,Polarity of I2S_WS pin" "0 at idle,1 at idle" endif width 13. textline " " if ((per.l(ad:0x04E20000+0x08))&0x1000)==0x1000 group.long 0x0C++0x03 line.long 0x00 "MCR0REG,Channel Control Register 0" bitfld.long 0x00 26.--30. " S1CHN ,Number of channel of sub frame 1" "1 channel,2 channel,3 channel,4 channel,5 channel,6 channel,7 channel,8 channel,9 channel,10 channel,11 channel,12 channel,13 channel,14 channel,15 channel,16 channel,17 channel,18 channel,19 channel,20 channel,21 channel,22 channel,23 channel,24 channel,25 channel,26 channel,27 channel,28 channel,29 channel,30 channel,31 channel,32 channel" bitfld.long 0x00 21.--25. " S1CHL ,Channel length of the channel constructing sub frame 1" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" bitfld.long 0x00 16.--20. " S1WDL ,Word length of the channel constructing sub frame 1" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" textline " " bitfld.long 0x00 10.--14. " S0CHN ,Number of channel of sub frame 0 is set up to 32 channels" "1 channel,2 channel,3 channel,4 channel,5 channel,6 channel,7 channel,8 channel,9 channel,10 channel,11 channel,12 channel,13 channel,14 channel,15 channel,16 channel,17 channel,18 channel,19 channel,20 channel,21 channel,22 channel,23 channel,24 channel,25 channel,26 channel,27 channel,28 channel,29 channel,30 channel,31 channel,32 channel" bitfld.long 0x00 5.--9. " S0CHL ,Channel length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" bitfld.long 0x00 0.--4. " S0WDL ,Word length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" else group.long 0x0C++0x03 line.long 0x00 "MCR0REG,Channel Control Register 0" bitfld.long 0x00 10.--14. " S0CHN ,Number of channel of sub frame 0 is set up to 32 channels" "1 channel,2 channel,3 channel,4 channel,5 channel,6 channel,7 channel,8 channel,9 channel,10 channel,11 channel,12 channel,13 channel,14 channel,15 channel,16 channel,17 channel,18 channel,19 channel,20 channel,21 channel,22 channel,23 channel,24 channel,25 channel,26 channel,27 channel,28 channel,29 channel,30 channel,31 channel,32 channel" bitfld.long 0x00 5.--9. " S0CHL ,Channel length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" bitfld.long 0x00 0.--4. " S0WDL ,Word length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" endif group.long 0x10++0x03 line.long 0x00 "MCR1REG,Channel Control Register 1" bitfld.long 0x00 31. " S0CH31 ,The S0CH31 bit controls the 31 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 30. " S0CH30 ,The S0CH30 bit controls the 30 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 29. " S0CH29 ,The S0CH29 bit controls the 29 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 28. " S0CH28 ,The S0CH28 bit controls the 28 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 27. " S0CH27 ,The S0CH27 bit controls the 27 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 26. " S0CH26 ,The S0CH26 bit controls the 26 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 25. " S0CH25 ,The S0CH25 bit controls the 25 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 24. " S0CH24 ,The S0CH24 bit controls the 24 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 23. " S0CH23 ,The S0CH23 bit controls the 23 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 22. " S0CH22 ,The S0CH22 bit controls the 22 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 21. " S0CH21 ,The S0CH21 bit controls the 21 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 20. " S0CH20 ,The S0CH20 bit controls the 20 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " S0CH19 ,The S0CH19 bit controls the 19 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 18. " S0CH18 ,The S0CH18 bit controls the 18 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 17. " S0CH17 ,The S0CH17 bit controls the 17 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 16. " S0CH16 ,The S0CH16 bit controls the 16 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 15. " S0CH15 ,The S0CH15 bit controls the 15 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 14. " S0CH14 ,The S0CH14 bit controls the 14 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 13. " S0CH13 ,The S0CH13 bit controls the 13 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 12. " S0CH12 ,The S0CH12 bit controls the 12 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " S0CH11 ,The S0CH11 bit controls the 11 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 10. " S0CH10 ,The S0CH10 bit controls the 10 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 9. " S0CH9 ,The S0CH9 bit controls the 9 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 8. " S0CH8 ,The S0CH8 bit controls the 8 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " S0CH7 ,The S0CH7 bit controls the 7 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 6. " S0CH6 ,The S0CH6 bit controls the 6 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 5. " S0CH5 ,The S0CH5 bit controls the 5 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 4. " S0CH4 ,The S0CH4 bit controls the 4 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " S0CH3 ,The S0CH3 bit controls the 3 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 2. " S0CH2 ,The S0CH2 bit controls the 2 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 1. " S0CH1 ,The S0CH1 bit controls the 1 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 0. " S0CH0 ,The S0CH0 bit controls the 0 channel of sub frame 0" "Disabled,Enabled" if (((per.l(ad:0x04E20000+0x08))&0x1000)==0x1000) group.long 0x14++0x03 line.long 0x00 "MCR2REG,Channel Control Register 2" bitfld.long 0x00 31. " S1CH31 ,The S1CH31 bit controls the 31 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 30. " S1CH30 ,The S1CH30 bit controls the 30 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 29. " S1CH29 ,The S1CH29 bit controls the 29 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 28. " S1CH28 ,The S1CH28 bit controls the 28 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 27. " S1CH27 ,The S1CH27 bit controls the 27 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 26. " S1CH26 ,The S1CH26 bit controls the 26 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 25. " S1CH25 ,The S1CH25 bit controls the 25 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 24. " S1CH24 ,The S1CH24 bit controls the 24 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 23. " S1CH23 ,The S1CH23 bit controls the 23 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 22. " S1CH22 ,The S1CH22 bit controls the 22 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 21. " S1CH21 ,The S1CH21 bit controls the 21 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 20. " S1CH20 ,The S1CH20 bit controls the 20 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " S1CH19 ,The S1CH19 bit controls the 19 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 18. " S1CH18 ,The S1CH18 bit controls the 18 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 17. " S1CH17 ,The S1CH17 bit controls the 17 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 16. " S1CH16 ,The S1CH16 bit controls the 16 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 15. " S1CH15 ,The S1CH15 bit controls the 15 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 14. " S1CH14 ,The S1CH14 bit controls the 14 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 13. " S1CH13 ,The S1CH13 bit controls the 13 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 12. " S1CH12 ,The S1CH12 bit controls the 12 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " S1CH11 ,The S1CH11 bit controls the 11 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 10. " S1CH10 ,The S1CH10 bit controls the 10 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 9. " S1CH9 ,The S1CH9 bit controls the 9 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 8. " S1CH8 ,The S1CH8 bit controls the 8 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " S1CH7 ,The S1CH7 bit controls the 7 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 6. " S1CH6 ,The S1CH6 bit controls the 6 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 5. " S1CH5 ,The S1CH5 bit controls the 5 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 4. " S1CH4 ,The S1CH4 bit controls the 4 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " S1CH3 ,The S1CH3 bit controls the 3 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 2. " S1CH2 ,The S1CH2 bit controls the 2 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 1. " S1CH1 ,The S1CH1 bit controls the 1 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 0. " S1CH0 ,The S1CH0 bit controls the 0 channel of sub frame 1" "Disabled,Enabled" textline " " else hgroup.long 0x14++0x03 hide.long 0x00 "MCR2REG,Channel Control Register 2" endif group.long 0x18++0x13 line.long 0x00 "OPRREG,Operation Control Register" bitfld.long 0x00 24. " RXENB ,Enable functions of receiving operation" "Disabled,Enabled" bitfld.long 0x00 16. " TXENB ,Enable functions of transmitting operation" "Disabled,Enabled" bitfld.long 0x00 0. " START ,I2S operation enable" "Disabled,Enabled" line.long 0x04 "SRST,Software Reset Register" bitfld.long 0x04 0. " SRST ,Software reset" "No reset,Reset" line.long 0x08 "INTCNT,Interrupt Control Register" bitfld.long 0x08 30. " TXUD1M ,Transmission FIFO underflow interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 29. " TBERM ,Interrupt mask bit of block size error of transmission channel" "Not masked,Masked" textline " " bitfld.long 0x08 28. " FERRM ,Frame error interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 27. " TXUD0M ,Transmission FIFO underflow interrupt mask bit" "Not masked,Masked" textline " " bitfld.long 0x08 26. " TXOVM ,Transmission FIFO overflow interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 25. " TXFDM ,DMA request mask register bit" "Request,Not request" textline " " bitfld.long 0x08 24. " TXFIM ,Transmission FIFO interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 21. " RBERM ,Interrupt mask bit of reception channel block size error" "Not masked,Masked" textline " " bitfld.long 0x08 20. " RXUDM ,Reception underflow interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 19. " RXOVM ,Interrupt mask bit of reception FIFO overflow" "Not masked,Masked" textline " " bitfld.long 0x08 18. " EOPM ,Interrupt mask bit by EOPI of STATUS register" "Not masked,Masked" bitfld.long 0x08 17. " RXFDM ,Reception DMA request mask bit" "Request,Not request" textline " " bitfld.long 0x08 16. " RXFIM ,Reception FIFO interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 8.--11. " TFTH ,Threshold value of transmission FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x08 4.--5. " RPTMR ,Packet reception completion timer setting bit" "0,54000 AHB clock cycles,108000 AHB clock cycles,216000 AHB clock cycles" bitfld.long 0x08 0.--3. " RFTH ,Threshold value of reception FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x0C "STATUS,STATUS Register" rbitfld.long 0x0C 31. " TBERR ,Block size of DMA transmission channel" "Disabled,Enabled" rbitfld.long 0x0C 30. " RBERR ,Block size of DMA reception channel" "Disabled,Enabled" textline " " eventfld.long 0x0C 29. " FERR ,Occurrence of frame error" "Disabled,Enabled" eventfld.long 0x0C 28. " TXUDR1 ,Transmission FIFO underflows at the top of frame" "Disabled,Enabled" textline " " eventfld.long 0x0C 27. " TXUDR0 ,Transmission FIFO underflows during frame transmission" "Disabled,Enabled" eventfld.long 0x0C 26. " TXOVR ,Transmission FIFO overflows" "Disabled,Enabled" textline " " eventfld.long 0x0C 25. " RXUDR ,Reception FIFO underflows" "Disabled,Enabled" eventfld.long 0x0C 24. " RXOVR ,Reception FIFO overflows" "Disabled,Enabled" textline " " eventfld.long 0x0C 19. " EOPI ,Interrupt flag containing reception timer" "Disabled,Enabled" rbitfld.long 0x0C 18. " BSY ,Serial transmission control part" "Idle,Busy" textline " " rbitfld.long 0x0C 17. " TXFI ,Number of empty slot of reception FIFO" "Disabled,Enabled" rbitfld.long 0x0C 16. " RXFI ,Number of reception FIFO data" "Disabled,Enabled" textline " " rbitfld.long 0x0C 8.--13. " TXNUM ,The number of data in transmission FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" rbitfld.long 0x0C 0.--5. " RXNUM ,The number of data in reception FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x10 "DMAACT,DMA Start-Up Register" sif (cpu()=="MB86R12")||(cpu()=="MB86R24") bitfld.long 0x10 24. " TL1E0 ,TXDREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " elif (cpu()=="MB86R11") rbitfld.long 0x10 24. " TL1E0 ,TXDREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " endif bitfld.long 0x10 16. " TDMACT ,Transmission channel of DMAC" "Not active,Active" textline " " sif (cpu()=="MB86R12")||(cpu()=="MB86R24") bitfld.long 0x10 8. " RL1E0 ,RXREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " elif (cpu()=="MB86R11") rbitfld.long 0x10 8. " RL1E0 ,RXREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " endif bitfld.long 0x10 0. " RDMACT ,The reception channel of DMAC" "Not active,Active" width 0x0B tree.end tree "I2S_3" base ad:0x04E30000 width 13. hgroup.long 0x00++0x03 hide.long 0x00 "RXFDAT,Reception FIFO Data Register" in wgroup.long 0x04++0x03 line.long 0x00 "TXFDAT,Transmission FIFO Data Register" if ((per.l(ad:0x04E30000+0x18))&0x01)==0x00 group.long 0x08++0x03 line.long 0x00 "CNTREG,Control Register" bitfld.long 0x00 26.--31. " CKRT ,Sets output clock frequency dividing ratio at master operation" "Bypassed,1/2,1/4,1/6,1/8,1/10,1/12,1/14,1/16,1/18,1/20,1/22,1/24,1/26,1/30,1/34,1/36,1/38,1/40,1/42,1/44,1/46,1/48,1/50,1/52,1/54,1/56,1/58,1/60,1/62,1/64,1/66,1/68,1/70,1/72,1/74,1/76,1/78,1/80,1/82,1/84,1/86,1/88,1/90,1/92,1/94,1/96,1/98,1/100,1/102,1/104,1/106,1/108,1/110,1/112,1/114,1/116,1/118,1/120,1/122,1/124,1/126,1/128,1/130" hexmask.long.word 0x00 16.--25. 1. " OVHD ,Frame rate is able to be adjusted by inserting OVHD bit following to valid data of the frame" textline " " bitfld.long 0x00 14. " MSKB ,Serial output data of invalid transmission frame" "Not set,Set" bitfld.long 0x00 13. " MSMD ,Master/Slave mode" "Slave,Master" textline " " bitfld.long 0x00 12. " SBFN ,Sub frame construction of the frame" "1 frame,2 frame" bitfld.long 0x00 11. " RHLL ,Handling of words in the FIFO" "1 word,2 word" textline " " bitfld.long 0x00 10. " ECKM ,Clock frequency division for master mode" "Internal clock,External clock" bitfld.long 0x00 9. " BEXT ,Extension mode" "Extended by 0,Extended by sign bit" textline " " bitfld.long 0x00 8. " FRUN ,Output mode of frame synchronous signal" "Burst mode,Free-running mode" bitfld.long 0x00 7. " MLSB ,Word bit's shift order" "MSB,LSB" textline " " bitfld.long 0x00 6. " TXDIS ,Transmitting function" "Enabled,Disabled" bitfld.long 0x00 5. " RXDIS ,Receiving function" "Enabled,Disabled" textline " " bitfld.long 0x00 4. " SMPL ,Sampling point of reception data" "Center,End" bitfld.long 0x00 3. " CPOL ,I2S_SCK polarity which drives/samples serial data" "Rising/Falling edge,Falling/Rising edge" textline " " bitfld.long 0x00 2. " FSPH ,Phase is specified to I2S_WS frame data" "1 clock before,Same time" bitfld.long 0x00 1. " FSLN ,Pulse width of I2S_WS" "1 bit,1 channel" textline " " bitfld.long 0x00 0. " FSPL ,Polarity of I2S_WS pin" "0 at idle,1 at idle" else rgroup.long 0x08++0x03 line.long 0x00 "CNTREG,Control Register" bitfld.long 0x00 26.--31. " CKRT ,Sets output clock frequency dividing ratio at master operation" "Bypassed,1/2,1/4,1/6,1/8,1/10,1/12,1/14,1/16,1/18,1/20,1/22,1/24,1/26,1/30,1/34,1/36,1/38,1/40,1/42,1/44,1/46,1/48,1/50,1/52,1/54,1/56,1/58,1/60,1/62,1/64,1/66,1/68,1/70,1/72,1/74,1/76,1/78,1/80,1/82,1/84,1/86,1/88,1/90,1/92,1/94,1/96,1/98,1/100,1/102,1/104,1/106,1/108,1/110,1/112,1/114,1/116,1/118,1/120,1/122,1/124,1/126,1/128,1/130" hexmask.long.word 0x00 16.--25. 1. " OVHD ,Frame rate is able to be adjusted by inserting OVHD bit following to valid data of the frame" textline " " bitfld.long 0x00 14. " MSKB ,Serial output data of invalid transmission frame" "Not set,Set" bitfld.long 0x00 13. " MSMD ,Master/Slave mode" "Slave,Master" textline " " bitfld.long 0x00 12. " SBFN ,Sub frame construction of the frame" "1 frame,2 frame" bitfld.long 0x00 11. " RHLL ,Handling of words in the FIFO" "1 word,2 word" textline " " bitfld.long 0x00 10. " ECKM ,Clock frequency division for master mode" "Internal clock,External clock" bitfld.long 0x00 9. " BEXT ,Extension mode" "Extended by 0,Extended by sign bit" textline " " bitfld.long 0x00 8. " FRUN ,Output mode of frame synchronous signal" "Burst mode,Free-running mode" bitfld.long 0x00 7. " MLSB ,Word bit's shift order" "MSB,LSB" textline " " bitfld.long 0x00 6. " TXDIS ,Transmitting function" "Enabled,Disabled" bitfld.long 0x00 5. " RXDIS ,Receiving function" "Enabled,Disabled" textline " " bitfld.long 0x00 4. " SMPL ,Sampling point of reception data" "Center,End" bitfld.long 0x00 3. " CPOL ,I2S_SCK polarity which drives/samples serial data" "Rising/Falling edge,Falling/Rising edge" textline " " bitfld.long 0x00 2. " FSPH ,Phase is specified to I2S_WS frame data" "1 clock before,Same time" bitfld.long 0x00 1. " FSLN ,Pulse width of I2S_WS" "1 bit,1 channel" textline " " bitfld.long 0x00 0. " FSPL ,Polarity of I2S_WS pin" "0 at idle,1 at idle" endif width 13. textline " " if ((per.l(ad:0x04E30000+0x08))&0x1000)==0x1000 group.long 0x0C++0x03 line.long 0x00 "MCR0REG,Channel Control Register 0" bitfld.long 0x00 26.--30. " S1CHN ,Number of channel of sub frame 1" "1 channel,2 channel,3 channel,4 channel,5 channel,6 channel,7 channel,8 channel,9 channel,10 channel,11 channel,12 channel,13 channel,14 channel,15 channel,16 channel,17 channel,18 channel,19 channel,20 channel,21 channel,22 channel,23 channel,24 channel,25 channel,26 channel,27 channel,28 channel,29 channel,30 channel,31 channel,32 channel" bitfld.long 0x00 21.--25. " S1CHL ,Channel length of the channel constructing sub frame 1" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" bitfld.long 0x00 16.--20. " S1WDL ,Word length of the channel constructing sub frame 1" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" textline " " bitfld.long 0x00 10.--14. " S0CHN ,Number of channel of sub frame 0 is set up to 32 channels" "1 channel,2 channel,3 channel,4 channel,5 channel,6 channel,7 channel,8 channel,9 channel,10 channel,11 channel,12 channel,13 channel,14 channel,15 channel,16 channel,17 channel,18 channel,19 channel,20 channel,21 channel,22 channel,23 channel,24 channel,25 channel,26 channel,27 channel,28 channel,29 channel,30 channel,31 channel,32 channel" bitfld.long 0x00 5.--9. " S0CHL ,Channel length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" bitfld.long 0x00 0.--4. " S0WDL ,Word length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" else group.long 0x0C++0x03 line.long 0x00 "MCR0REG,Channel Control Register 0" bitfld.long 0x00 10.--14. " S0CHN ,Number of channel of sub frame 0 is set up to 32 channels" "1 channel,2 channel,3 channel,4 channel,5 channel,6 channel,7 channel,8 channel,9 channel,10 channel,11 channel,12 channel,13 channel,14 channel,15 channel,16 channel,17 channel,18 channel,19 channel,20 channel,21 channel,22 channel,23 channel,24 channel,25 channel,26 channel,27 channel,28 channel,29 channel,30 channel,31 channel,32 channel" bitfld.long 0x00 5.--9. " S0CHL ,Channel length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" bitfld.long 0x00 0.--4. " S0WDL ,Word length of the channel constructing sub frame 0" ",,,,,,7 bit,8 bit,9 bit,10 bit,11 bit,12 bit,13 bit,14 bit,15 bit,16 bit,17 bit,18 bit,19 bit,20 bit,21 bit,22 bit,23 bit,24 bit,25 bit,26 bit,27 bit,28 bit,29 bit,30 bit,31 bit,32 bit" endif group.long 0x10++0x03 line.long 0x00 "MCR1REG,Channel Control Register 1" bitfld.long 0x00 31. " S0CH31 ,The S0CH31 bit controls the 31 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 30. " S0CH30 ,The S0CH30 bit controls the 30 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 29. " S0CH29 ,The S0CH29 bit controls the 29 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 28. " S0CH28 ,The S0CH28 bit controls the 28 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 27. " S0CH27 ,The S0CH27 bit controls the 27 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 26. " S0CH26 ,The S0CH26 bit controls the 26 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 25. " S0CH25 ,The S0CH25 bit controls the 25 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 24. " S0CH24 ,The S0CH24 bit controls the 24 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 23. " S0CH23 ,The S0CH23 bit controls the 23 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 22. " S0CH22 ,The S0CH22 bit controls the 22 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 21. " S0CH21 ,The S0CH21 bit controls the 21 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 20. " S0CH20 ,The S0CH20 bit controls the 20 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " S0CH19 ,The S0CH19 bit controls the 19 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 18. " S0CH18 ,The S0CH18 bit controls the 18 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 17. " S0CH17 ,The S0CH17 bit controls the 17 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 16. " S0CH16 ,The S0CH16 bit controls the 16 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 15. " S0CH15 ,The S0CH15 bit controls the 15 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 14. " S0CH14 ,The S0CH14 bit controls the 14 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 13. " S0CH13 ,The S0CH13 bit controls the 13 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 12. " S0CH12 ,The S0CH12 bit controls the 12 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " S0CH11 ,The S0CH11 bit controls the 11 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 10. " S0CH10 ,The S0CH10 bit controls the 10 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 9. " S0CH9 ,The S0CH9 bit controls the 9 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 8. " S0CH8 ,The S0CH8 bit controls the 8 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " S0CH7 ,The S0CH7 bit controls the 7 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 6. " S0CH6 ,The S0CH6 bit controls the 6 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 5. " S0CH5 ,The S0CH5 bit controls the 5 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 4. " S0CH4 ,The S0CH4 bit controls the 4 channel of sub frame 0" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " S0CH3 ,The S0CH3 bit controls the 3 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 2. " S0CH2 ,The S0CH2 bit controls the 2 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 1. " S0CH1 ,The S0CH1 bit controls the 1 channel of sub frame 0" "Disabled,Enabled" bitfld.long 0x00 0. " S0CH0 ,The S0CH0 bit controls the 0 channel of sub frame 0" "Disabled,Enabled" if (((per.l(ad:0x04E30000+0x08))&0x1000)==0x1000) group.long 0x14++0x03 line.long 0x00 "MCR2REG,Channel Control Register 2" bitfld.long 0x00 31. " S1CH31 ,The S1CH31 bit controls the 31 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 30. " S1CH30 ,The S1CH30 bit controls the 30 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 29. " S1CH29 ,The S1CH29 bit controls the 29 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 28. " S1CH28 ,The S1CH28 bit controls the 28 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 27. " S1CH27 ,The S1CH27 bit controls the 27 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 26. " S1CH26 ,The S1CH26 bit controls the 26 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 25. " S1CH25 ,The S1CH25 bit controls the 25 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 24. " S1CH24 ,The S1CH24 bit controls the 24 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 23. " S1CH23 ,The S1CH23 bit controls the 23 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 22. " S1CH22 ,The S1CH22 bit controls the 22 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 21. " S1CH21 ,The S1CH21 bit controls the 21 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 20. " S1CH20 ,The S1CH20 bit controls the 20 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " S1CH19 ,The S1CH19 bit controls the 19 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 18. " S1CH18 ,The S1CH18 bit controls the 18 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 17. " S1CH17 ,The S1CH17 bit controls the 17 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 16. " S1CH16 ,The S1CH16 bit controls the 16 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 15. " S1CH15 ,The S1CH15 bit controls the 15 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 14. " S1CH14 ,The S1CH14 bit controls the 14 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 13. " S1CH13 ,The S1CH13 bit controls the 13 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 12. " S1CH12 ,The S1CH12 bit controls the 12 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " S1CH11 ,The S1CH11 bit controls the 11 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 10. " S1CH10 ,The S1CH10 bit controls the 10 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 9. " S1CH9 ,The S1CH9 bit controls the 9 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 8. " S1CH8 ,The S1CH8 bit controls the 8 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " S1CH7 ,The S1CH7 bit controls the 7 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 6. " S1CH6 ,The S1CH6 bit controls the 6 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 5. " S1CH5 ,The S1CH5 bit controls the 5 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 4. " S1CH4 ,The S1CH4 bit controls the 4 channel of sub frame 1" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " S1CH3 ,The S1CH3 bit controls the 3 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 2. " S1CH2 ,The S1CH2 bit controls the 2 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 1. " S1CH1 ,The S1CH1 bit controls the 1 channel of sub frame 1" "Disabled,Enabled" bitfld.long 0x00 0. " S1CH0 ,The S1CH0 bit controls the 0 channel of sub frame 1" "Disabled,Enabled" textline " " else hgroup.long 0x14++0x03 hide.long 0x00 "MCR2REG,Channel Control Register 2" endif group.long 0x18++0x13 line.long 0x00 "OPRREG,Operation Control Register" bitfld.long 0x00 24. " RXENB ,Enable functions of receiving operation" "Disabled,Enabled" bitfld.long 0x00 16. " TXENB ,Enable functions of transmitting operation" "Disabled,Enabled" bitfld.long 0x00 0. " START ,I2S operation enable" "Disabled,Enabled" line.long 0x04 "SRST,Software Reset Register" bitfld.long 0x04 0. " SRST ,Software reset" "No reset,Reset" line.long 0x08 "INTCNT,Interrupt Control Register" bitfld.long 0x08 30. " TXUD1M ,Transmission FIFO underflow interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 29. " TBERM ,Interrupt mask bit of block size error of transmission channel" "Not masked,Masked" textline " " bitfld.long 0x08 28. " FERRM ,Frame error interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 27. " TXUD0M ,Transmission FIFO underflow interrupt mask bit" "Not masked,Masked" textline " " bitfld.long 0x08 26. " TXOVM ,Transmission FIFO overflow interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 25. " TXFDM ,DMA request mask register bit" "Request,Not request" textline " " bitfld.long 0x08 24. " TXFIM ,Transmission FIFO interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 21. " RBERM ,Interrupt mask bit of reception channel block size error" "Not masked,Masked" textline " " bitfld.long 0x08 20. " RXUDM ,Reception underflow interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 19. " RXOVM ,Interrupt mask bit of reception FIFO overflow" "Not masked,Masked" textline " " bitfld.long 0x08 18. " EOPM ,Interrupt mask bit by EOPI of STATUS register" "Not masked,Masked" bitfld.long 0x08 17. " RXFDM ,Reception DMA request mask bit" "Request,Not request" textline " " bitfld.long 0x08 16. " RXFIM ,Reception FIFO interrupt mask bit" "Not masked,Masked" bitfld.long 0x08 8.--11. " TFTH ,Threshold value of transmission FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x08 4.--5. " RPTMR ,Packet reception completion timer setting bit" "0,54000 AHB clock cycles,108000 AHB clock cycles,216000 AHB clock cycles" bitfld.long 0x08 0.--3. " RFTH ,Threshold value of reception FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x0C "STATUS,STATUS Register" rbitfld.long 0x0C 31. " TBERR ,Block size of DMA transmission channel" "Disabled,Enabled" rbitfld.long 0x0C 30. " RBERR ,Block size of DMA reception channel" "Disabled,Enabled" textline " " eventfld.long 0x0C 29. " FERR ,Occurrence of frame error" "Disabled,Enabled" eventfld.long 0x0C 28. " TXUDR1 ,Transmission FIFO underflows at the top of frame" "Disabled,Enabled" textline " " eventfld.long 0x0C 27. " TXUDR0 ,Transmission FIFO underflows during frame transmission" "Disabled,Enabled" eventfld.long 0x0C 26. " TXOVR ,Transmission FIFO overflows" "Disabled,Enabled" textline " " eventfld.long 0x0C 25. " RXUDR ,Reception FIFO underflows" "Disabled,Enabled" eventfld.long 0x0C 24. " RXOVR ,Reception FIFO overflows" "Disabled,Enabled" textline " " eventfld.long 0x0C 19. " EOPI ,Interrupt flag containing reception timer" "Disabled,Enabled" rbitfld.long 0x0C 18. " BSY ,Serial transmission control part" "Idle,Busy" textline " " rbitfld.long 0x0C 17. " TXFI ,Number of empty slot of reception FIFO" "Disabled,Enabled" rbitfld.long 0x0C 16. " RXFI ,Number of reception FIFO data" "Disabled,Enabled" textline " " rbitfld.long 0x0C 8.--13. " TXNUM ,The number of data in transmission FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" rbitfld.long 0x0C 0.--5. " RXNUM ,The number of data in reception FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x10 "DMAACT,DMA Start-Up Register" sif (cpu()=="MB86R12")||(cpu()=="MB86R24") bitfld.long 0x10 24. " TL1E0 ,TXDREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " elif (cpu()=="MB86R11") rbitfld.long 0x10 24. " TL1E0 ,TXDREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " endif bitfld.long 0x10 16. " TDMACT ,Transmission channel of DMAC" "Not active,Active" textline " " sif (cpu()=="MB86R12")||(cpu()=="MB86R24") bitfld.long 0x10 8. " RL1E0 ,RXREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " elif (cpu()=="MB86R11") rbitfld.long 0x10 8. " RL1E0 ,RXREQ mode" "Edge-Sensitive mode,Level-Sensitive mode" textline " " endif bitfld.long 0x10 0. " RDMACT ,The reception channel of DMAC" "Not active,Active" width 0x0B tree.end tree.end tree "UART" tree "UART0" base ad:0x3E000000 width 9. if (((per.l(ad:0x3E000000+0x0C))&0x80)==0x00) hgroup.long 0x00++0x03 hide.long 0x00 "RFR/TFR,Reception/Transmission FIFO Register" in group.long 0x04++0x03 line.long 0x00 "IER,Interrupt Enable Register" bitfld.long 0x00 3. " EDSSI ,Enable modem status interrupt" "Disabled,Enabled" bitfld.long 0x00 2. " ELSI ,Enable receiver status interrupt" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " ETBEI ,Enable transmitter FIFO register empty interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " ERBFI ,Enable receiver FIFO register" "Disabled,Enabled" else hgroup.long 0x00++0x07 hide.long 0x00 "RFR/TFR,Reception/Transmission FIFO Register" hide.long 0x04 "IER,Interrupt Enable Register" endif rgroup.long 0x08++0x03 line.long 0x00 "IIR,Interrupt ID Register" bitfld.long 0x00 6.--7. " FIFO ,FIFO status fixed to '11'" "0,1,2,3" bitfld.long 0x00 0.--3. " ID ,Interrupt setting" "Modem status,No interrupt,Transmission FIFO is empty,,Reception data existed,,Reception line status,,,,,,Time-out,?..." wgroup.long 0x08++0x03 line.long 0x00 "FCR,FIFO Control Register" bitfld.long 0x00 6.--7. " RCVR ,Reception FIFO's trigger level" "1byte,4bytes,8bytes,14bytes" bitfld.long 0x00 3. " DMA_MODE ,DMA transfer mode" "Single,Demand" textline " " bitfld.long 0x00 2. " TXF_RST ,Transmission FIFO reset" "No reset,Reset" bitfld.long 0x00 1. " RXF_RST ,Reception FIFO reset" "No reset,Reset" if (((per.l(ad:0x3E000000+0x0C))&0x03)==0x00) group.long 0x0C++0x03 line.long 0x00 "LCR,Line Control Register" bitfld.long 0x00 7. " DLAB ,Divisor latch access bit" "Disabled,Enabled" bitfld.long 0x00 6. " SB ,Set break" "SOUT1,Forced to 0" textline " " bitfld.long 0x00 5. " SP ,Stick parity" "EPS-PEN,Fixed" bitfld.long 0x00 4. " EPS ,Even parity select" "Odd parity,Even parity" textline " " bitfld.long 0x00 3. " PEN ,Parity enable" "Disabled,Enabled" bitfld.long 0x00 2. " STB ,Number of stop bit" "1bit,1.5bits" textline " " bitfld.long 0x00 0.--1. " WLS ,Word length select" "5bit,6bit,7bit,8bit" else group.long 0x0C++0x03 line.long 0x00 "LCR,Line Control Register" bitfld.long 0x00 7. " DLAB ,Divisor latch access bit" "Disabled,Enabled" bitfld.long 0x00 6. " SB ,Set break" "SOUT1,Forced to 0" textline " " bitfld.long 0x00 5. " SP ,Stick parity" "EPS-PEN,Fixed" bitfld.long 0x00 4. " EPS ,Even parity select" "Odd parity,Even parity" textline " " bitfld.long 0x00 3. " PEN ,Parity enable" "Disabled,Enabled" bitfld.long 0x00 2. " STB ,Number of stop bit" "1bit,2bits" textline " " bitfld.long 0x00 0.--1. " WLS ,Word length select" "5bit,6bit,7bit,8bit" endif group.long 0x10++0x03 line.long 0x00 "MCR,Modem Control Register" sif (cpu()!="MB86R01")&&(cpu()!="MB86R24") bitfld.long 0x00 4. " LOOP ,Loop back mode" "Not set,Set" bitfld.long 0x00 3. " OUT2 ,OUT2 control signal" "Not active,Active" textline " " bitfld.long 0x00 2. " OUT1 ,OUT1 control signal" "Not active,Active" bitfld.long 0x00 1. " RTS ,RTS control signal" "Not active,Active" textline " " bitfld.long 0x00 0. " DTR ,DTR control signal" "Not active,Active" else bitfld.long 0x00 4. " LOOP ,Loop back mode" "Not set,Set" bitfld.long 0x00 1. " RTS ,RTS control signal" "Not active,Active" endif hgroup.long 0x14++0x07 hide.long 0x00 "LSR,Line Status Register" in hide.long 0x04 "MSR,Modem Status Register" in if (((per.l(ad:0x3E000000+0x0C))&0x80)==0x80) group.long 0x00++0x07 line.long 0x00 "DLL,Divider Latch Register" hexmask.long.byte 0x00 0.--7. 1. " DL ,Low order byte" line.long 0x04 "DLM,Divider Latch Register" hexmask.long.word 0x04 0.--15. 1. " DLM ,High order byte" else hgroup.long 0x00++0x07 hide.long 0x00 "DLL,Divider Latch Register" hide.long 0x04 "DLM,Divider Latch Register" endif width 0x0B tree.end tree "UART1" base ad:0x3E010000 width 9. if (((per.l(ad:0x3E010000+0x0C))&0x80)==0x00) hgroup.long 0x00++0x03 hide.long 0x00 "RFR/TFR,Reception/Transmission FIFO Register" in group.long 0x04++0x03 line.long 0x00 "IER,Interrupt Enable Register" bitfld.long 0x00 3. " EDSSI ,Enable modem status interrupt" "Disabled,Enabled" bitfld.long 0x00 2. " ELSI ,Enable receiver status interrupt" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " ETBEI ,Enable transmitter FIFO register empty interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " ERBFI ,Enable receiver FIFO register" "Disabled,Enabled" else hgroup.long 0x00++0x07 hide.long 0x00 "RFR/TFR,Reception/Transmission FIFO Register" hide.long 0x04 "IER,Interrupt Enable Register" endif rgroup.long 0x08++0x03 line.long 0x00 "IIR,Interrupt ID Register" bitfld.long 0x00 6.--7. " FIFO ,FIFO status fixed to '11'" "0,1,2,3" bitfld.long 0x00 0.--3. " ID ,Interrupt setting" "Modem status,No interrupt,Transmission FIFO is empty,,Reception data existed,,Reception line status,,,,,,Time-out,?..." wgroup.long 0x08++0x03 line.long 0x00 "FCR,FIFO Control Register" bitfld.long 0x00 6.--7. " RCVR ,Reception FIFO's trigger level" "1byte,4bytes,8bytes,14bytes" bitfld.long 0x00 3. " DMA_MODE ,DMA transfer mode" "Single,Demand" textline " " bitfld.long 0x00 2. " TXF_RST ,Transmission FIFO reset" "No reset,Reset" bitfld.long 0x00 1. " RXF_RST ,Reception FIFO reset" "No reset,Reset" if (((per.l(ad:0x3E010000+0x0C))&0x03)==0x00) group.long 0x0C++0x03 line.long 0x00 "LCR,Line Control Register" bitfld.long 0x00 7. " DLAB ,Divisor latch access bit" "Disabled,Enabled" bitfld.long 0x00 6. " SB ,Set break" "SOUT1,Forced to 0" textline " " bitfld.long 0x00 5. " SP ,Stick parity" "EPS-PEN,Fixed" bitfld.long 0x00 4. " EPS ,Even parity select" "Odd parity,Even parity" textline " " bitfld.long 0x00 3. " PEN ,Parity enable" "Disabled,Enabled" bitfld.long 0x00 2. " STB ,Number of stop bit" "1bit,1.5bits" textline " " bitfld.long 0x00 0.--1. " WLS ,Word length select" "5bit,6bit,7bit,8bit" else group.long 0x0C++0x03 line.long 0x00 "LCR,Line Control Register" bitfld.long 0x00 7. " DLAB ,Divisor latch access bit" "Disabled,Enabled" bitfld.long 0x00 6. " SB ,Set break" "SOUT1,Forced to 0" textline " " bitfld.long 0x00 5. " SP ,Stick parity" "EPS-PEN,Fixed" bitfld.long 0x00 4. " EPS ,Even parity select" "Odd parity,Even parity" textline " " bitfld.long 0x00 3. " PEN ,Parity enable" "Disabled,Enabled" bitfld.long 0x00 2. " STB ,Number of stop bit" "1bit,2bits" textline " " bitfld.long 0x00 0.--1. " WLS ,Word length select" "5bit,6bit,7bit,8bit" endif group.long 0x10++0x03 line.long 0x00 "MCR,Modem Control Register" sif (cpu()!="MB86R01")&&(cpu()!="MB86R24") bitfld.long 0x00 4. " LOOP ,Loop back mode" "Not set,Set" bitfld.long 0x00 3. " OUT2 ,OUT2 control signal" "Not active,Active" textline " " bitfld.long 0x00 2. " OUT1 ,OUT1 control signal" "Not active,Active" bitfld.long 0x00 1. " RTS ,RTS control signal" "Not active,Active" textline " " bitfld.long 0x00 0. " DTR ,DTR control signal" "Not active,Active" else bitfld.long 0x00 4. " LOOP ,Loop back mode" "Not set,Set" bitfld.long 0x00 1. " RTS ,RTS control signal" "Not active,Active" endif hgroup.long 0x14++0x07 hide.long 0x00 "LSR,Line Status Register" in hide.long 0x04 "MSR,Modem Status Register" in if (((per.l(ad:0x3E010000+0x0C))&0x80)==0x80) group.long 0x00++0x07 line.long 0x00 "DLL,Divider Latch Register" hexmask.long.byte 0x00 0.--7. 1. " DL ,Low order byte" line.long 0x04 "DLM,Divider Latch Register" hexmask.long.word 0x04 0.--15. 1. " DLM ,High order byte" else hgroup.long 0x00++0x07 hide.long 0x00 "DLL,Divider Latch Register" hide.long 0x04 "DLM,Divider Latch Register" endif width 0x0B tree.end tree "UART2" base ad:0x3E020000 width 9. if (((per.l(ad:0x3E020000+0x0C))&0x80)==0x00) hgroup.long 0x00++0x03 hide.long 0x00 "RFR/TFR,Reception/Transmission FIFO Register" in group.long 0x04++0x03 line.long 0x00 "IER,Interrupt Enable Register" bitfld.long 0x00 3. " EDSSI ,Enable modem status interrupt" "Disabled,Enabled" bitfld.long 0x00 2. " ELSI ,Enable receiver status interrupt" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " ETBEI ,Enable transmitter FIFO register empty interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " ERBFI ,Enable receiver FIFO register" "Disabled,Enabled" else hgroup.long 0x00++0x07 hide.long 0x00 "RFR/TFR,Reception/Transmission FIFO Register" hide.long 0x04 "IER,Interrupt Enable Register" endif rgroup.long 0x08++0x03 line.long 0x00 "IIR,Interrupt ID Register" bitfld.long 0x00 6.--7. " FIFO ,FIFO status fixed to '11'" "0,1,2,3" bitfld.long 0x00 0.--3. " ID ,Interrupt setting" "Modem status,No interrupt,Transmission FIFO is empty,,Reception data existed,,Reception line status,,,,,,Time-out,?..." wgroup.long 0x08++0x03 line.long 0x00 "FCR,FIFO Control Register" bitfld.long 0x00 6.--7. " RCVR ,Reception FIFO's trigger level" "1byte,4bytes,8bytes,14bytes" bitfld.long 0x00 3. " DMA_MODE ,DMA transfer mode" "Single,Demand" textline " " bitfld.long 0x00 2. " TXF_RST ,Transmission FIFO reset" "No reset,Reset" bitfld.long 0x00 1. " RXF_RST ,Reception FIFO reset" "No reset,Reset" if (((per.l(ad:0x3E020000+0x0C))&0x03)==0x00) group.long 0x0C++0x03 line.long 0x00 "LCR,Line Control Register" bitfld.long 0x00 7. " DLAB ,Divisor latch access bit" "Disabled,Enabled" bitfld.long 0x00 6. " SB ,Set break" "SOUT1,Forced to 0" textline " " bitfld.long 0x00 5. " SP ,Stick parity" "EPS-PEN,Fixed" bitfld.long 0x00 4. " EPS ,Even parity select" "Odd parity,Even parity" textline " " bitfld.long 0x00 3. " PEN ,Parity enable" "Disabled,Enabled" bitfld.long 0x00 2. " STB ,Number of stop bit" "1bit,1.5bits" textline " " bitfld.long 0x00 0.--1. " WLS ,Word length select" "5bit,6bit,7bit,8bit" else group.long 0x0C++0x03 line.long 0x00 "LCR,Line Control Register" bitfld.long 0x00 7. " DLAB ,Divisor latch access bit" "Disabled,Enabled" bitfld.long 0x00 6. " SB ,Set break" "SOUT1,Forced to 0" textline " " bitfld.long 0x00 5. " SP ,Stick parity" "EPS-PEN,Fixed" bitfld.long 0x00 4. " EPS ,Even parity select" "Odd parity,Even parity" textline " " bitfld.long 0x00 3. " PEN ,Parity enable" "Disabled,Enabled" bitfld.long 0x00 2. " STB ,Number of stop bit" "1bit,2bits" textline " " bitfld.long 0x00 0.--1. " WLS ,Word length select" "5bit,6bit,7bit,8bit" endif group.long 0x10++0x03 line.long 0x00 "MCR,Modem Control Register" sif (cpu()!="MB86R01")&&(cpu()!="MB86R24") bitfld.long 0x00 4. " LOOP ,Loop back mode" "Not set,Set" bitfld.long 0x00 3. " OUT2 ,OUT2 control signal" "Not active,Active" textline " " bitfld.long 0x00 2. " OUT1 ,OUT1 control signal" "Not active,Active" bitfld.long 0x00 1. " RTS ,RTS control signal" "Not active,Active" textline " " bitfld.long 0x00 0. " DTR ,DTR control signal" "Not active,Active" else bitfld.long 0x00 4. " LOOP ,Loop back mode" "Not set,Set" bitfld.long 0x00 1. " RTS ,RTS control signal" "Not active,Active" endif hgroup.long 0x14++0x07 hide.long 0x00 "LSR,Line Status Register" in hide.long 0x04 "MSR,Modem Status Register" in if (((per.l(ad:0x3E020000+0x0C))&0x80)==0x80) group.long 0x00++0x07 line.long 0x00 "DLL,Divider Latch Register" hexmask.long.byte 0x00 0.--7. 1. " DL ,Low order byte" line.long 0x04 "DLM,Divider Latch Register" hexmask.long.word 0x04 0.--15. 1. " DLM ,High order byte" else hgroup.long 0x00++0x07 hide.long 0x00 "DLL,Divider Latch Register" hide.long 0x04 "DLM,Divider Latch Register" endif width 0x0B tree.end tree "UART3" base ad:0x3E030000 width 9. if (((per.l(ad:0x3E030000+0x0C))&0x80)==0x00) hgroup.long 0x00++0x03 hide.long 0x00 "RFR/TFR,Reception/Transmission FIFO Register" in group.long 0x04++0x03 line.long 0x00 "IER,Interrupt Enable Register" bitfld.long 0x00 3. " EDSSI ,Enable modem status interrupt" "Disabled,Enabled" bitfld.long 0x00 2. " ELSI ,Enable receiver status interrupt" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " ETBEI ,Enable transmitter FIFO register empty interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " ERBFI ,Enable receiver FIFO register" "Disabled,Enabled" else hgroup.long 0x00++0x07 hide.long 0x00 "RFR/TFR,Reception/Transmission FIFO Register" hide.long 0x04 "IER,Interrupt Enable Register" endif rgroup.long 0x08++0x03 line.long 0x00 "IIR,Interrupt ID Register" bitfld.long 0x00 6.--7. " FIFO ,FIFO status fixed to '11'" "0,1,2,3" bitfld.long 0x00 0.--3. " ID ,Interrupt setting" "Modem status,No interrupt,Transmission FIFO is empty,,Reception data existed,,Reception line status,,,,,,Time-out,?..." wgroup.long 0x08++0x03 line.long 0x00 "FCR,FIFO Control Register" bitfld.long 0x00 6.--7. " RCVR ,Reception FIFO's trigger level" "1byte,4bytes,8bytes,14bytes" bitfld.long 0x00 3. " DMA_MODE ,DMA transfer mode" "Single,Demand" textline " " bitfld.long 0x00 2. " TXF_RST ,Transmission FIFO reset" "No reset,Reset" bitfld.long 0x00 1. " RXF_RST ,Reception FIFO reset" "No reset,Reset" if (((per.l(ad:0x3E030000+0x0C))&0x03)==0x00) group.long 0x0C++0x03 line.long 0x00 "LCR,Line Control Register" bitfld.long 0x00 7. " DLAB ,Divisor latch access bit" "Disabled,Enabled" bitfld.long 0x00 6. " SB ,Set break" "SOUT1,Forced to 0" textline " " bitfld.long 0x00 5. " SP ,Stick parity" "EPS-PEN,Fixed" bitfld.long 0x00 4. " EPS ,Even parity select" "Odd parity,Even parity" textline " " bitfld.long 0x00 3. " PEN ,Parity enable" "Disabled,Enabled" bitfld.long 0x00 2. " STB ,Number of stop bit" "1bit,1.5bits" textline " " bitfld.long 0x00 0.--1. " WLS ,Word length select" "5bit,6bit,7bit,8bit" else group.long 0x0C++0x03 line.long 0x00 "LCR,Line Control Register" bitfld.long 0x00 7. " DLAB ,Divisor latch access bit" "Disabled,Enabled" bitfld.long 0x00 6. " SB ,Set break" "SOUT1,Forced to 0" textline " " bitfld.long 0x00 5. " SP ,Stick parity" "EPS-PEN,Fixed" bitfld.long 0x00 4. " EPS ,Even parity select" "Odd parity,Even parity" textline " " bitfld.long 0x00 3. " PEN ,Parity enable" "Disabled,Enabled" bitfld.long 0x00 2. " STB ,Number of stop bit" "1bit,2bits" textline " " bitfld.long 0x00 0.--1. " WLS ,Word length select" "5bit,6bit,7bit,8bit" endif group.long 0x10++0x03 line.long 0x00 "MCR,Modem Control Register" sif (cpu()!="MB86R01")&&(cpu()!="MB86R24") bitfld.long 0x00 4. " LOOP ,Loop back mode" "Not set,Set" bitfld.long 0x00 3. " OUT2 ,OUT2 control signal" "Not active,Active" textline " " bitfld.long 0x00 2. " OUT1 ,OUT1 control signal" "Not active,Active" bitfld.long 0x00 1. " RTS ,RTS control signal" "Not active,Active" textline " " bitfld.long 0x00 0. " DTR ,DTR control signal" "Not active,Active" else bitfld.long 0x00 4. " LOOP ,Loop back mode" "Not set,Set" bitfld.long 0x00 1. " RTS ,RTS control signal" "Not active,Active" endif hgroup.long 0x14++0x07 hide.long 0x00 "LSR,Line Status Register" in hide.long 0x04 "MSR,Modem Status Register" in if (((per.l(ad:0x3E030000+0x0C))&0x80)==0x80) group.long 0x00++0x07 line.long 0x00 "DLL,Divider Latch Register" hexmask.long.byte 0x00 0.--7. 1. " DL ,Low order byte" line.long 0x04 "DLM,Divider Latch Register" hexmask.long.word 0x04 0.--15. 1. " DLM ,High order byte" else hgroup.long 0x00++0x07 hide.long 0x00 "DLL,Divider Latch Register" hide.long 0x04 "DLM,Divider Latch Register" endif width 0x0B tree.end tree "UART4" base ad:0x3E040000 width 9. if (((per.l(ad:0x3E040000+0x0C))&0x80)==0x00) hgroup.long 0x00++0x03 hide.long 0x00 "RFR/TFR,Reception/Transmission FIFO Register" in group.long 0x04++0x03 line.long 0x00 "IER,Interrupt Enable Register" bitfld.long 0x00 3. " EDSSI ,Enable modem status interrupt" "Disabled,Enabled" bitfld.long 0x00 2. " ELSI ,Enable receiver status interrupt" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " ETBEI ,Enable transmitter FIFO register empty interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " ERBFI ,Enable receiver FIFO register" "Disabled,Enabled" else hgroup.long 0x00++0x07 hide.long 0x00 "RFR/TFR,Reception/Transmission FIFO Register" hide.long 0x04 "IER,Interrupt Enable Register" endif rgroup.long 0x08++0x03 line.long 0x00 "IIR,Interrupt ID Register" bitfld.long 0x00 6.--7. " FIFO ,FIFO status fixed to '11'" "0,1,2,3" bitfld.long 0x00 0.--3. " ID ,Interrupt setting" "Modem status,No interrupt,Transmission FIFO is empty,,Reception data existed,,Reception line status,,,,,,Time-out,?..." wgroup.long 0x08++0x03 line.long 0x00 "FCR,FIFO Control Register" bitfld.long 0x00 6.--7. " RCVR ,Reception FIFO's trigger level" "1byte,4bytes,8bytes,14bytes" bitfld.long 0x00 3. " DMA_MODE ,DMA transfer mode" "Single,Demand" textline " " bitfld.long 0x00 2. " TXF_RST ,Transmission FIFO reset" "No reset,Reset" bitfld.long 0x00 1. " RXF_RST ,Reception FIFO reset" "No reset,Reset" if (((per.l(ad:0x3E040000+0x0C))&0x03)==0x00) group.long 0x0C++0x03 line.long 0x00 "LCR,Line Control Register" bitfld.long 0x00 7. " DLAB ,Divisor latch access bit" "Disabled,Enabled" bitfld.long 0x00 6. " SB ,Set break" "SOUT1,Forced to 0" textline " " bitfld.long 0x00 5. " SP ,Stick parity" "EPS-PEN,Fixed" bitfld.long 0x00 4. " EPS ,Even parity select" "Odd parity,Even parity" textline " " bitfld.long 0x00 3. " PEN ,Parity enable" "Disabled,Enabled" bitfld.long 0x00 2. " STB ,Number of stop bit" "1bit,1.5bits" textline " " bitfld.long 0x00 0.--1. " WLS ,Word length select" "5bit,6bit,7bit,8bit" else group.long 0x0C++0x03 line.long 0x00 "LCR,Line Control Register" bitfld.long 0x00 7. " DLAB ,Divisor latch access bit" "Disabled,Enabled" bitfld.long 0x00 6. " SB ,Set break" "SOUT1,Forced to 0" textline " " bitfld.long 0x00 5. " SP ,Stick parity" "EPS-PEN,Fixed" bitfld.long 0x00 4. " EPS ,Even parity select" "Odd parity,Even parity" textline " " bitfld.long 0x00 3. " PEN ,Parity enable" "Disabled,Enabled" bitfld.long 0x00 2. " STB ,Number of stop bit" "1bit,2bits" textline " " bitfld.long 0x00 0.--1. " WLS ,Word length select" "5bit,6bit,7bit,8bit" endif group.long 0x10++0x03 line.long 0x00 "MCR,Modem Control Register" sif (cpu()!="MB86R01")&&(cpu()!="MB86R24") bitfld.long 0x00 4. " LOOP ,Loop back mode" "Not set,Set" bitfld.long 0x00 3. " OUT2 ,OUT2 control signal" "Not active,Active" textline " " bitfld.long 0x00 2. " OUT1 ,OUT1 control signal" "Not active,Active" bitfld.long 0x00 1. " RTS ,RTS control signal" "Not active,Active" textline " " bitfld.long 0x00 0. " DTR ,DTR control signal" "Not active,Active" else bitfld.long 0x00 4. " LOOP ,Loop back mode" "Not set,Set" bitfld.long 0x00 1. " RTS ,RTS control signal" "Not active,Active" endif hgroup.long 0x14++0x07 hide.long 0x00 "LSR,Line Status Register" in hide.long 0x04 "MSR,Modem Status Register" in if (((per.l(ad:0x3E040000+0x0C))&0x80)==0x80) group.long 0x00++0x07 line.long 0x00 "DLL,Divider Latch Register" hexmask.long.byte 0x00 0.--7. 1. " DL ,Low order byte" line.long 0x04 "DLM,Divider Latch Register" hexmask.long.word 0x04 0.--15. 1. " DLM ,High order byte" else hgroup.long 0x00++0x07 hide.long 0x00 "DLL,Divider Latch Register" hide.long 0x04 "DLM,Divider Latch Register" endif width 0x0B tree.end tree "UART5" base ad:0x3E050000 width 9. if (((per.l(ad:0x3E050000+0x0C))&0x80)==0x00) hgroup.long 0x00++0x03 hide.long 0x00 "RFR/TFR,Reception/Transmission FIFO Register" in group.long 0x04++0x03 line.long 0x00 "IER,Interrupt Enable Register" bitfld.long 0x00 3. " EDSSI ,Enable modem status interrupt" "Disabled,Enabled" bitfld.long 0x00 2. " ELSI ,Enable receiver status interrupt" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " ETBEI ,Enable transmitter FIFO register empty interrupt" "Disabled,Enabled" bitfld.long 0x00 0. " ERBFI ,Enable receiver FIFO register" "Disabled,Enabled" else hgroup.long 0x00++0x07 hide.long 0x00 "RFR/TFR,Reception/Transmission FIFO Register" hide.long 0x04 "IER,Interrupt Enable Register" endif rgroup.long 0x08++0x03 line.long 0x00 "IIR,Interrupt ID Register" bitfld.long 0x00 6.--7. " FIFO ,FIFO status fixed to '11'" "0,1,2,3" bitfld.long 0x00 0.--3. " ID ,Interrupt setting" "Modem status,No interrupt,Transmission FIFO is empty,,Reception data existed,,Reception line status,,,,,,Time-out,?..." wgroup.long 0x08++0x03 line.long 0x00 "FCR,FIFO Control Register" bitfld.long 0x00 6.--7. " RCVR ,Reception FIFO's trigger level" "1byte,4bytes,8bytes,14bytes" bitfld.long 0x00 3. " DMA_MODE ,DMA transfer mode" "Single,Demand" textline " " bitfld.long 0x00 2. " TXF_RST ,Transmission FIFO reset" "No reset,Reset" bitfld.long 0x00 1. " RXF_RST ,Reception FIFO reset" "No reset,Reset" if (((per.l(ad:0x3E050000+0x0C))&0x03)==0x00) group.long 0x0C++0x03 line.long 0x00 "LCR,Line Control Register" bitfld.long 0x00 7. " DLAB ,Divisor latch access bit" "Disabled,Enabled" bitfld.long 0x00 6. " SB ,Set break" "SOUT1,Forced to 0" textline " " bitfld.long 0x00 5. " SP ,Stick parity" "EPS-PEN,Fixed" bitfld.long 0x00 4. " EPS ,Even parity select" "Odd parity,Even parity" textline " " bitfld.long 0x00 3. " PEN ,Parity enable" "Disabled,Enabled" bitfld.long 0x00 2. " STB ,Number of stop bit" "1bit,1.5bits" textline " " bitfld.long 0x00 0.--1. " WLS ,Word length select" "5bit,6bit,7bit,8bit" else group.long 0x0C++0x03 line.long 0x00 "LCR,Line Control Register" bitfld.long 0x00 7. " DLAB ,Divisor latch access bit" "Disabled,Enabled" bitfld.long 0x00 6. " SB ,Set break" "SOUT1,Forced to 0" textline " " bitfld.long 0x00 5. " SP ,Stick parity" "EPS-PEN,Fixed" bitfld.long 0x00 4. " EPS ,Even parity select" "Odd parity,Even parity" textline " " bitfld.long 0x00 3. " PEN ,Parity enable" "Disabled,Enabled" bitfld.long 0x00 2. " STB ,Number of stop bit" "1bit,2bits" textline " " bitfld.long 0x00 0.--1. " WLS ,Word length select" "5bit,6bit,7bit,8bit" endif group.long 0x10++0x03 line.long 0x00 "MCR,Modem Control Register" sif (cpu()!="MB86R01")&&(cpu()!="MB86R24") bitfld.long 0x00 4. " LOOP ,Loop back mode" "Not set,Set" bitfld.long 0x00 3. " OUT2 ,OUT2 control signal" "Not active,Active" textline " " bitfld.long 0x00 2. " OUT1 ,OUT1 control signal" "Not active,Active" bitfld.long 0x00 1. " RTS ,RTS control signal" "Not active,Active" textline " " bitfld.long 0x00 0. " DTR ,DTR control signal" "Not active,Active" else bitfld.long 0x00 4. " LOOP ,Loop back mode" "Not set,Set" bitfld.long 0x00 1. " RTS ,RTS control signal" "Not active,Active" endif hgroup.long 0x14++0x07 hide.long 0x00 "LSR,Line Status Register" in hide.long 0x04 "MSR,Modem Status Register" in if (((per.l(ad:0x3E050000+0x0C))&0x80)==0x80) group.long 0x00++0x07 line.long 0x00 "DLL,Divider Latch Register" hexmask.long.byte 0x00 0.--7. 1. " DL ,Low order byte" line.long 0x04 "DLM,Divider Latch Register" hexmask.long.word 0x04 0.--15. 1. " DLM ,High order byte" else hgroup.long 0x00++0x07 hide.long 0x00 "DLL,Divider Latch Register" hide.long 0x04 "DLM,Divider Latch Register" endif width 0x0B tree.end tree.end tree "USART" tree "USART_0" base ad:0x3F000000 width 14. group.byte 0x00++0x00 "Mode and Control Registers" line.byte 0x00 "SMR,Serial Mode Register" bitfld.byte 0x0 6.--7. " MD ,Operation Mode Select" "Asynchronous normal,Asynchronous multiprocessor,Synchronous,Asynchronous LIN" bitfld.byte 0x0 5. " OTO ,One-to-One External Clock Selection" "Reload counter,External clock" bitfld.byte 0x0 4. " EXT ,External Clock Selection" "Reload counter,External clock" textline " " bitfld.byte 0x0 3. " REST ,Restart of Transmission Reload Counter" "No reset,Restart" bitfld.byte 0x0 2. " UPCL ,LIN-USART Programmable Clear" "No reset,Reset" if ((((per.b(ad:0x3F000000))&0xC0)==0x00)||(((per.b(ad:0x3F000000))&0xC0)==0x80)&&(((per.b(ad:0x3F000000+0x0C))&0x08)==0x08)) group.byte 0x01++0x00 line.byte 0x0 "SCR,Serial Control Register" bitfld.byte 0x0 7. " PEN ,Parity Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " P ,Parity Selection" "Even,Odd" bitfld.byte 0x0 5. " SBL ,Stop Bit Length Selection" "1,2" textline " " bitfld.byte 0x0 4. " CL ,Character (Data frame) Length (in bits)" "7,8" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " AD_SET/CLR ,Address or Data Selection" "Data,Address" bitfld.byte 0x0 2. " CRE ,Clear Reception Error Flags" "No effect,Clear" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXE_SET/CLR ,Reception Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXE_SET/CLR ,Transmission Enable" "Disabled,Enabled" else group.byte 0x01++0x00 line.byte 0x0 "SCR,Serial Control Register" bitfld.byte 0x0 6. " P ,Parity Selection" "Even,Odd" bitfld.byte 0x0 5. " SBL ,Stop Bit Length Selection" "1,2" textline " " bitfld.byte 0x0 4. " CL ,Character (Data frame) Length (in bits)" "7,8" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " AD_SET/CLR ,Address or Data Selection" "Data,Address" bitfld.byte 0x0 2. " CRE ,Clear Reception Error Flags" "No effect,Clear" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXE_SET/CLR ,Reception Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXE_SET/CLR ,Transmission Enable" "Disabled,Enabled" endif wgroup.byte 0x2++0x1 line.byte 0x0 "SMSR,Serial Mode Set Register" bitfld.byte 0x0 3. " RESTS ,REST Set" "No effect,Set" bitfld.byte 0x0 2. " UPCLS ,UPCL Set" "No effect,Set" line.byte 0x1 "SCSR,Serial Control Set Register" bitfld.byte 0x1 2. " CRES ,CRE Set" "No effect,Set" wgroup.byte 0x06++0x0 "Transmission Data Register" line.byte 0x0 "TDR,Transmission Data Register" hexmask.byte 0x0 0.--7. 1. " D[7:0] ,Transmission data" group.byte 0x07++0x0 "Status Register" line.byte 0x0 "SSR,Serial Status Register" rbitfld.byte 0x0 7. " PE ,Parity Error Flag" "No error,Error" rbitfld.byte 0x0 6. " ORE ,Overrun Error Flag" "No error,Error" rbitfld.byte 0x0 5. " FRE ,Framing Error Flag" "No error,Error" textline " " rbitfld.byte 0x0 4. " RDRF ,Receive Data Register Full Flag" "Empty,Full" bitfld.byte 0x0 3. " TDRE ,Transmission Data Register Empty" "Full,Empty" bitfld.byte 0x0 2. " BDS ,Transfer Direction Selection" "LSB,MSB" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RIE_SET/CLR ,Receive Interrupt Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TIE_SET/CLR ,Transmission Interrupt Request Enable" "Disabled,Enabled" hgroup.byte 0x08++0x00 "Reception Data Register" hide.byte 0x0 "RDR,Reception Data Register" in if ((((per.b(ad:0x3F000000+0x0C))&0x20)==0x20)&&(((per.b(ad:0x3F000000))&0xC0)==0x80)) group.byte 0x0C++0x00 "Extended Registers" line.byte 0x0 "ECCR,Extended Communication Control Register" bitfld.byte 0x0 7. " INV ,Invert Serial Data" "Not inverted,Inverted" bitfld.byte 0x0 6. " LBR ,Generate LIN Sync Break" "Ignored,Generated" bitfld.byte 0x0 5. " MS ,Master Slave Mode select" "Master mode,Slave mode" textline " " bitfld.byte 0x0 4. " SCDE ,Serial Clock Delay Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " SSM ,Start_Stop Bit Mode Enable" "Disabled,Enabled" else group.byte 0x0C++0x00 "Extended Registers" line.byte 0x0 "ECCR,Extended Communication Control Register" bitfld.byte 0x0 7. " INV ,Invert Serial Data" "Not inverted,Inverted" bitfld.byte 0x0 6. " LBR ,Generate LIN Sync Break" "Ignored,Generated" bitfld.byte 0x0 5. " MS ,Master Slave Mode select" "Master mode,Slave mode" textline " " bitfld.byte 0x0 4. " SCDE ,Serial Clock Delay Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " SSM ,Start_Stop Bit Mode Enable" "Disabled,Enabled" bitfld.byte 0x0 2. " BIE ,Bus Idle Interrupt Enable" "Disabled,Enabled" textline " " rbitfld.byte 0x0 1. " RBI ,Reception Bus Idle Flag" "Reception,No reception" rbitfld.byte 0x0 0. " TBI ,Transmission Bus Idle Flag" "Transmission,No transmission" endif if (((per.b(ad:0x3F000000+0x19))&0x1)==0x0) group.byte 0x0D++0x00 line.byte 0x0 "ESCR,Extended Status/Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " LBIE_SET/CLR ,LIN Sync Break Detection Interrupt Enable" "Disabled,Enabled" rbitfld.byte 0x0 6. " LBD ,Sync Break Detected Flag" "Not detected,Detected" bitfld.byte 0x0 4.--5. " LBL ,LIN Sync Break Length Selection (in bit times)" "13,14,15,16" textline " " bitfld.byte 0x0 3. " SOPE ,Serial Output Pin Direct Access Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " SOIP_SET/CLR ,Serial Input Output Pin Direct Access" "Low,High" bitfld.byte 0x0 1. " CCO ,Continuous Clock Output Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " SCES ,Serial Clock Edge Select" "Rising edge,Falling edge" else group.byte 0x0D++0x00 line.byte 0x0 "ESCR,Extended Status/Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " LBIE_SET/CLR ,LIN Sync Break Detection Interrupt Enable" "Disabled,Enabled" rbitfld.byte 0x0 6. " LBD ,Sync Break Detected Flag" "Not detected,Detected" bitfld.byte 0x0 4.--5. " LBL ,LIN Sync Break Length Selection (in bit times)" "17,18,19,20" textline " " bitfld.byte 0x0 3. " SOPE ,Serial Output Pin Direct Access Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " SOIP_SET/CLR ,Serial Input Output Pin Direct Access" "Low,High" bitfld.byte 0x0 1. " CCO ,Continuous Clock Output Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " SCES ,Serial Clock Edge Select" "Rising edge,Falling edge" endif group.byte 0x0E++0x00 line.byte 0x0 "ECCSR,Extended Communication Control Set Register" bitfld.byte 0x0 6. " LBRS ,LBR Set" "No effect,Set" bitfld.byte 0x0 2. " BIES ,BIE Set" "No effect,Set" group.byte 0x10++0x01 line.byte 0x00 "ECCCR,Extended Communication Control Clear Register" bitfld.byte 0x0 2. " BIEC ,BIE Clear" "No effect,Clear" line.byte 0x01 "ESCCR,Extended Status/Control Clear Register" bitfld.byte 0x1 6. " LBDC ,LBD Clear" "No effect,Clear" group.byte 0x12++0x00 line.byte 0x0 "ESIR,Extended Serial Interrupt Register" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " PEIE_SET/CLR ,Parity Error (in data received) Interrupt Enable bit" "Disabled,Enabled" setclrfld.byte 0x0 5. 0x2 5. 0x4 5. " OREIE_SET/CLR ,Overrun Error Interrupt Enable bit" "Disabled,Enabled" setclrfld.byte 0x0 4. 0x2 4. 0x4 4. " FREIE_SET/CLR ,Framing Error Interrupt Enable bit" "Disabled,Enabled" textline " " bitfld.byte 0x0 3. " TDRE ,Transmission Data Register Empty (Sticky Behaviour)" "Full,Empty" bitfld.byte 0x0 2. " RDRF ,Reception Data Register Full (Sticky Behaviour)" "Empty,Full" bitfld.byte 0x0 1. " RBI ,Reception Bus Idle (Sticky Behaviour)" "Reception,No reception" textline " " bitfld.byte 0x0 0. " AICD ,Auto Interrupt Clear Disable" "Enabled,Disabled" if (((per.b(ad:0x3F000000))&0xC0)==0xC0) group.byte 0x13++0x0 line.byte 0x0 "EIER,Extended Interrupt Enable Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFIE_SET/CLR ,Transmission FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " RXFIE_SET/CLR ,Reception FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 5. 0x2 5. 0x4 5. " SYNFEIE_SET/CLR ,Sync Field Error Interrupt Enable" "Disabled,Enabled" textline " " setclrfld.byte 0x0 4. 0x2 4. 0x4 4. " RXHDIE_SET/CLR ,Reception Header Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " TXHDIE_SET/CLR ,Transmission Header Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " PEFRDIE_SET/CLR ,Parity Error in Frame-ID Received Interrupt Enable" "Disabled,Enabled" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " BUSERRIE_SET/CLR ,Bus Error Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " LBSOIE_SET/CLR ,BLast Bit Shifted Out Interrupt Enable bit" "Disabled,Enabled" else group.byte 0x13++0x0 line.byte 0x0 "EIER,Extended Interrupt Enable Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFIE_SET/CLR ,Transmission FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " RXFIE_SET/CLR ,Reception FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " LBSOIE_SET/CLR ,BLast Bit Shifted Out Interrupt Enable bit" "Disabled,Enabled" endif wgroup.byte 0x16++0x0 line.byte 0x0 "ESICR,Extended Serial Interrupt Clear Register" bitfld.byte 0x0 3. " TDREC ,Transmission Data Register Empty Flag (TDRE) Clear" "No effect,Clear" bitfld.byte 0x0 2. " RDRFC ,Reception Data Register Full Flag (RDRF) Clear" "No effect,Clear" bitfld.byte 0x0 1. " RBIC ,Reception Bus Idle Flag (RBI) Clear" "No effect,Clear" group.byte 0x18++0x1 line.byte 0x0 "EFERL,Extended Feature Enable Register - L" bitfld.byte 0x0 6. " OSDE ,Oversampling Disable" "No,Yes" bitfld.byte 0x0 5. " DTSTART ,Detect Start bit" "Low level,Falling edge" bitfld.byte 0x0 4. " RSTRFM ,Reset Reception State Machine" "Enabled,Disabled" textline " " bitfld.byte 0x0 3. " LBEDGE ,LIN Break Edge Sensitive" "Level,Edge" bitfld.byte 0x0 2. " ABRE ,Auto Baud Rate Detection/Adjustment Enable" "Disabled,Enabled" bitfld.byte 0x0 1. " ENRXHR ,Automatic Header Detection Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " ENTXHR ,Automatic Header Transmission Enable" "Disabled,Enabled" line.byte 0x1 "EFERH,Extended Feature Enable Register - H" bitfld.byte 0x1 5. " INTLBEN ,Internal Loop Back Enable" "Disabled,Enabled" bitfld.byte 0x1 4. " BRGR ,Baud Rate Regiter Read" "Reload Counter Value,Reload Value of CPU/ABR" bitfld.byte 0x1 3. " FIDPE ,Enable for Parity Checking of Frame-ID" "Disabled,Enabled" textline " " bitfld.byte 0x1 2. " DBE ,Detection of Bus Error Enable" "Disabled,Enabled" bitfld.byte 0x1 1. " FIDE ,Frame-ID Register Enable" "Disabled,Enabled" bitfld.byte 0x1 0. " LBL2 ,MSB of LIN Break Length" "13-16,17-20" group.byte 0x1A++0x0 line.byte 0x0 "RFCR,Reception FIFO Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " RXFE_SET/CLR ,Reception FIFO Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " RXFCL ,Reception FIFO Clear" "Not reset,Reset" bitfld.byte 0x0 0.--4. " RXFLC ,Reception FIFO Level Configuration (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," group.byte 0x1B++0x0 line.byte 0x0 "TFCR,Transmission FIFO Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFE_SET/CLR ,Transmission FIFO Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " TXFCL ,Transmission FIFO Clear" "Not reset,Reset" bitfld.byte 0x0 0.--4. " TXFLC ,Transmission FIFO Level Configuration (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," wgroup.byte 0x1E++0x1 line.byte 0x0 "RFCCR,Reception FIFO Control Clear Register" bitfld.byte 0x0 6. " RXFCLC ,RXFCL Clear" "No effect,Clear" line.byte 0x1 "TFCCR,Transmission FIFO Control Clear Register" bitfld.byte 0x1 6. " TXFCLC ,TXFCL Clear" "No effect,Clear" group.byte 0x20++0x1 line.byte 0x0 "RFSR,Reception FIFO Status Register" bitfld.byte 0x0 0.--4. " RXFVD ,Reception FIFO Valid Data (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," line.byte 0x1 "TFSR,Transmission FIFO Status Register" bitfld.byte 0x1 0.--4. " TXFVD ,Transmission FIFO Valid Data (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," group.byte 0x22++0x0 "Checksum Register" line.byte 0x0 "CSCR,Checksum Status and Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " CRCERRIE_set/clr ,Checksum Error Interrupt Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " CCRCERR ,CRC Error Flag" "No error,Error" bitfld.byte 0x0 5. " CRCTYPE ,Checksum Type" "Classic,Enhanced" textline " " bitfld.byte 0x0 4. " CRCCHECK ,Checksum Verification Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " CRCGEN ,Checksum Generation Enable" "Disabled,Enabled" bitfld.byte 0x0 0.--2. " DL ,Data Length in LIN Frame (in bytes)" "1,2,3,4,5,6,7,8" wgroup.byte 0x26++0x0 line.byte 0x0 "CSCCR,Checksum Status and Control Clear Register" bitfld.byte 0x0 6. " CRCERRC ,CRCERR Clear" "No effect,Clear" rgroup.byte 0x23++0x0 "Status Register" line.byte 0x0 "ESR,Extended Status Register" bitfld.byte 0x0 6. " AD ,AD Status of Received Frame" "Usual data,Address" bitfld.byte 0x0 5. " TXHRI ,Transmission of Header" "Not completed,Completed" bitfld.byte 0x0 4. " RXHRI ,Reception of Header" "Not completed,Completed" textline " " bitfld.byte 0x0 3. " LBSOF ,Last Bit Shift Out Flag" "Not shifted out,Shifted out" bitfld.byte 0x0 2. " BUSERR ,Bus Error Flag" "No error,Error" bitfld.byte 0x0 1. " PEFRD ,Parity Error in Frame-ID" "No error,Error" textline " " bitfld.byte 0x0 0. " SYNFE ,Sync Field Error Flag" "No error,Error" wgroup.byte 0x27++0x0 line.byte 0x0 "ESCLR,Extended Status Clear Register" bitfld.byte 0x00 5. " TXHRIC ,TXHRI Clear" "No effect,Clear" bitfld.byte 0x00 4. " RXHRIC ,RXHRI Clear" "No effect,Clear" bitfld.byte 0x00 3. " LBSOFC ,LBSOF Clear" "No effect,Clear" textline " " bitfld.byte 0x00 2. " BUSERRC ,BUSERR Clear" "No effect,Clear" bitfld.byte 0x00 1. " PEFRDC ,PEFRD Clear" "No effect,Clear" bitfld.byte 0x00 0. " SYNFEC ,SYNFEC Clear" "No effect,Clear" wgroup.byte 0x28++0x2 "Baud Rate Registers" line.byte 0x0 "BGRLL,Baud Rate Generation Reload Register - L (bits[7:0])" line.byte 0x1 "BGRLM,Baud Rate Generation Reload Register - M (bits[15:8])" line.byte 0x2 "BGRLH,Baud Rate Generation Reload Register - H (bits[18:16])" bitfld.byte 0x2 0.--2. " Value[18:16] ,Baud Rate Generation Reload Register - H bits 16..18" "0,1,2,3,4,5,6,7" rgroup.byte 0x2C++0x2 line.byte 0x0 "BGRL,Baud Rate Generation Register - L (bits[0:7])" line.byte 0x1 "BGRM,Baud Rate Generation Register - M (bits[8:15])" line.byte 0x2 "BGRH,Baud Rate Generation Register - H (bits[16:18])" bitfld.byte 0x2 0.--2. " Value[18:16] ,Baud Rate Generation Register - H bits 16..18" "0,1,2,3,4,5,6,7" group.byte 0x30++0x00 "DMA Configuration Registers" line.byte 0x0 "STXDR,Serial Transmit DMA Configuration Register" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " TXDISDOERR_SET/CLR ,TX-DMA Request Mask/Disable" "No,Yes" setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " TXDRQEN_SET/CLR ,TX-DMA Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXDDEN_SET/CLR ,TX-DMA Demand Transfer Enable" "Disabled,Enabled" group.byte 0x31++0x00 line.byte 0x0 "SRXDR,Serial Receive DMA Configuration Register" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " RXDISDOERR_SET/CLR ,RX-DMA Request Mask/Disable" "No,Yes" setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXDRQEN_SET/CLR ,RX-DMA Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " RXDDEN_SET/CLR ,RX-DMA Demand Transfer Enable" "Disabled,Enabled" group.byte 0x36++0x02 "Sync Field Timeout Registers" line.byte 0x00 "SFTRL,Sync Field Timeout Register - L (bits[7:0])" line.byte 0x01 "SFTRM,Sync Field Timeout Register - M (bits[15:8])" line.byte 0x02 "SFTRH,Sync Field Timeout Register - H (bits[18:16])" bitfld.byte 0x02 0.--2. " VALUE[18:16] ,Sync Field Timeout Register - H bits 16..18" "0,1,2,3,4,5,6,7" group.byte 0x3A++0x0 "Frame-ID and Debug Register" line.byte 0x0 "FIDR,Frame-ID Register" sif (cpu()!="MB86R11F") group.byte 0x3C++0x0 line.byte 0x0 "DEBUG,Debug Register" bitfld.byte 0x0 0. " DBGEN ,Debug Enable" "Disabled,Enabled" endif width 12. tree.end tree "USART_1" base ad:0x3F010000 width 14. group.byte 0x00++0x00 "Mode and Control Registers" line.byte 0x00 "SMR,Serial Mode Register" bitfld.byte 0x0 6.--7. " MD ,Operation Mode Select" "Asynchronous normal,Asynchronous multiprocessor,Synchronous,Asynchronous LIN" bitfld.byte 0x0 5. " OTO ,One-to-One External Clock Selection" "Reload counter,External clock" bitfld.byte 0x0 4. " EXT ,External Clock Selection" "Reload counter,External clock" textline " " bitfld.byte 0x0 3. " REST ,Restart of Transmission Reload Counter" "No reset,Restart" bitfld.byte 0x0 2. " UPCL ,LIN-USART Programmable Clear" "No reset,Reset" if ((((per.b(ad:0x3F010000))&0xC0)==0x00)||(((per.b(ad:0x3F010000))&0xC0)==0x80)&&(((per.b(ad:0x3F010000+0x0C))&0x08)==0x08)) group.byte 0x01++0x00 line.byte 0x0 "SCR,Serial Control Register" bitfld.byte 0x0 7. " PEN ,Parity Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " P ,Parity Selection" "Even,Odd" bitfld.byte 0x0 5. " SBL ,Stop Bit Length Selection" "1,2" textline " " bitfld.byte 0x0 4. " CL ,Character (Data frame) Length (in bits)" "7,8" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " AD_SET/CLR ,Address or Data Selection" "Data,Address" bitfld.byte 0x0 2. " CRE ,Clear Reception Error Flags" "No effect,Clear" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXE_SET/CLR ,Reception Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXE_SET/CLR ,Transmission Enable" "Disabled,Enabled" else group.byte 0x01++0x00 line.byte 0x0 "SCR,Serial Control Register" bitfld.byte 0x0 6. " P ,Parity Selection" "Even,Odd" bitfld.byte 0x0 5. " SBL ,Stop Bit Length Selection" "1,2" textline " " bitfld.byte 0x0 4. " CL ,Character (Data frame) Length (in bits)" "7,8" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " AD_SET/CLR ,Address or Data Selection" "Data,Address" bitfld.byte 0x0 2. " CRE ,Clear Reception Error Flags" "No effect,Clear" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXE_SET/CLR ,Reception Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXE_SET/CLR ,Transmission Enable" "Disabled,Enabled" endif wgroup.byte 0x2++0x1 line.byte 0x0 "SMSR,Serial Mode Set Register" bitfld.byte 0x0 3. " RESTS ,REST Set" "No effect,Set" bitfld.byte 0x0 2. " UPCLS ,UPCL Set" "No effect,Set" line.byte 0x1 "SCSR,Serial Control Set Register" bitfld.byte 0x1 2. " CRES ,CRE Set" "No effect,Set" wgroup.byte 0x06++0x0 "Transmission Data Register" line.byte 0x0 "TDR,Transmission Data Register" hexmask.byte 0x0 0.--7. 1. " D[7:0] ,Transmission data" group.byte 0x07++0x0 "Status Register" line.byte 0x0 "SSR,Serial Status Register" rbitfld.byte 0x0 7. " PE ,Parity Error Flag" "No error,Error" rbitfld.byte 0x0 6. " ORE ,Overrun Error Flag" "No error,Error" rbitfld.byte 0x0 5. " FRE ,Framing Error Flag" "No error,Error" textline " " rbitfld.byte 0x0 4. " RDRF ,Receive Data Register Full Flag" "Empty,Full" bitfld.byte 0x0 3. " TDRE ,Transmission Data Register Empty" "Full,Empty" bitfld.byte 0x0 2. " BDS ,Transfer Direction Selection" "LSB,MSB" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RIE_SET/CLR ,Receive Interrupt Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TIE_SET/CLR ,Transmission Interrupt Request Enable" "Disabled,Enabled" hgroup.byte 0x08++0x00 "Reception Data Register" hide.byte 0x0 "RDR,Reception Data Register" in if ((((per.b(ad:0x3F010000+0x0C))&0x20)==0x20)&&(((per.b(ad:0x3F010000))&0xC0)==0x80)) group.byte 0x0C++0x00 "Extended Registers" line.byte 0x0 "ECCR,Extended Communication Control Register" bitfld.byte 0x0 7. " INV ,Invert Serial Data" "Not inverted,Inverted" bitfld.byte 0x0 6. " LBR ,Generate LIN Sync Break" "Ignored,Generated" bitfld.byte 0x0 5. " MS ,Master Slave Mode select" "Master mode,Slave mode" textline " " bitfld.byte 0x0 4. " SCDE ,Serial Clock Delay Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " SSM ,Start_Stop Bit Mode Enable" "Disabled,Enabled" else group.byte 0x0C++0x00 "Extended Registers" line.byte 0x0 "ECCR,Extended Communication Control Register" bitfld.byte 0x0 7. " INV ,Invert Serial Data" "Not inverted,Inverted" bitfld.byte 0x0 6. " LBR ,Generate LIN Sync Break" "Ignored,Generated" bitfld.byte 0x0 5. " MS ,Master Slave Mode select" "Master mode,Slave mode" textline " " bitfld.byte 0x0 4. " SCDE ,Serial Clock Delay Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " SSM ,Start_Stop Bit Mode Enable" "Disabled,Enabled" bitfld.byte 0x0 2. " BIE ,Bus Idle Interrupt Enable" "Disabled,Enabled" textline " " rbitfld.byte 0x0 1. " RBI ,Reception Bus Idle Flag" "Reception,No reception" rbitfld.byte 0x0 0. " TBI ,Transmission Bus Idle Flag" "Transmission,No transmission" endif if (((per.b(ad:0x3F010000+0x19))&0x1)==0x0) group.byte 0x0D++0x00 line.byte 0x0 "ESCR,Extended Status/Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " LBIE_SET/CLR ,LIN Sync Break Detection Interrupt Enable" "Disabled,Enabled" rbitfld.byte 0x0 6. " LBD ,Sync Break Detected Flag" "Not detected,Detected" bitfld.byte 0x0 4.--5. " LBL ,LIN Sync Break Length Selection (in bit times)" "13,14,15,16" textline " " bitfld.byte 0x0 3. " SOPE ,Serial Output Pin Direct Access Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " SOIP_SET/CLR ,Serial Input Output Pin Direct Access" "Low,High" bitfld.byte 0x0 1. " CCO ,Continuous Clock Output Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " SCES ,Serial Clock Edge Select" "Rising edge,Falling edge" else group.byte 0x0D++0x00 line.byte 0x0 "ESCR,Extended Status/Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " LBIE_SET/CLR ,LIN Sync Break Detection Interrupt Enable" "Disabled,Enabled" rbitfld.byte 0x0 6. " LBD ,Sync Break Detected Flag" "Not detected,Detected" bitfld.byte 0x0 4.--5. " LBL ,LIN Sync Break Length Selection (in bit times)" "17,18,19,20" textline " " bitfld.byte 0x0 3. " SOPE ,Serial Output Pin Direct Access Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " SOIP_SET/CLR ,Serial Input Output Pin Direct Access" "Low,High" bitfld.byte 0x0 1. " CCO ,Continuous Clock Output Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " SCES ,Serial Clock Edge Select" "Rising edge,Falling edge" endif group.byte 0x0E++0x00 line.byte 0x0 "ECCSR,Extended Communication Control Set Register" bitfld.byte 0x0 6. " LBRS ,LBR Set" "No effect,Set" bitfld.byte 0x0 2. " BIES ,BIE Set" "No effect,Set" group.byte 0x10++0x01 line.byte 0x00 "ECCCR,Extended Communication Control Clear Register" bitfld.byte 0x0 2. " BIEC ,BIE Clear" "No effect,Clear" line.byte 0x01 "ESCCR,Extended Status/Control Clear Register" bitfld.byte 0x1 6. " LBDC ,LBD Clear" "No effect,Clear" group.byte 0x12++0x00 line.byte 0x0 "ESIR,Extended Serial Interrupt Register" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " PEIE_SET/CLR ,Parity Error (in data received) Interrupt Enable bit" "Disabled,Enabled" setclrfld.byte 0x0 5. 0x2 5. 0x4 5. " OREIE_SET/CLR ,Overrun Error Interrupt Enable bit" "Disabled,Enabled" setclrfld.byte 0x0 4. 0x2 4. 0x4 4. " FREIE_SET/CLR ,Framing Error Interrupt Enable bit" "Disabled,Enabled" textline " " bitfld.byte 0x0 3. " TDRE ,Transmission Data Register Empty (Sticky Behaviour)" "Full,Empty" bitfld.byte 0x0 2. " RDRF ,Reception Data Register Full (Sticky Behaviour)" "Empty,Full" bitfld.byte 0x0 1. " RBI ,Reception Bus Idle (Sticky Behaviour)" "Reception,No reception" textline " " bitfld.byte 0x0 0. " AICD ,Auto Interrupt Clear Disable" "Enabled,Disabled" if (((per.b(ad:0x3F010000))&0xC0)==0xC0) group.byte 0x13++0x0 line.byte 0x0 "EIER,Extended Interrupt Enable Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFIE_SET/CLR ,Transmission FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " RXFIE_SET/CLR ,Reception FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 5. 0x2 5. 0x4 5. " SYNFEIE_SET/CLR ,Sync Field Error Interrupt Enable" "Disabled,Enabled" textline " " setclrfld.byte 0x0 4. 0x2 4. 0x4 4. " RXHDIE_SET/CLR ,Reception Header Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " TXHDIE_SET/CLR ,Transmission Header Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " PEFRDIE_SET/CLR ,Parity Error in Frame-ID Received Interrupt Enable" "Disabled,Enabled" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " BUSERRIE_SET/CLR ,Bus Error Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " LBSOIE_SET/CLR ,BLast Bit Shifted Out Interrupt Enable bit" "Disabled,Enabled" else group.byte 0x13++0x0 line.byte 0x0 "EIER,Extended Interrupt Enable Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFIE_SET/CLR ,Transmission FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " RXFIE_SET/CLR ,Reception FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " LBSOIE_SET/CLR ,BLast Bit Shifted Out Interrupt Enable bit" "Disabled,Enabled" endif wgroup.byte 0x16++0x0 line.byte 0x0 "ESICR,Extended Serial Interrupt Clear Register" bitfld.byte 0x0 3. " TDREC ,Transmission Data Register Empty Flag (TDRE) Clear" "No effect,Clear" bitfld.byte 0x0 2. " RDRFC ,Reception Data Register Full Flag (RDRF) Clear" "No effect,Clear" bitfld.byte 0x0 1. " RBIC ,Reception Bus Idle Flag (RBI) Clear" "No effect,Clear" group.byte 0x18++0x1 line.byte 0x0 "EFERL,Extended Feature Enable Register - L" bitfld.byte 0x0 6. " OSDE ,Oversampling Disable" "No,Yes" bitfld.byte 0x0 5. " DTSTART ,Detect Start bit" "Low level,Falling edge" bitfld.byte 0x0 4. " RSTRFM ,Reset Reception State Machine" "Enabled,Disabled" textline " " bitfld.byte 0x0 3. " LBEDGE ,LIN Break Edge Sensitive" "Level,Edge" bitfld.byte 0x0 2. " ABRE ,Auto Baud Rate Detection/Adjustment Enable" "Disabled,Enabled" bitfld.byte 0x0 1. " ENRXHR ,Automatic Header Detection Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " ENTXHR ,Automatic Header Transmission Enable" "Disabled,Enabled" line.byte 0x1 "EFERH,Extended Feature Enable Register - H" bitfld.byte 0x1 5. " INTLBEN ,Internal Loop Back Enable" "Disabled,Enabled" bitfld.byte 0x1 4. " BRGR ,Baud Rate Regiter Read" "Reload Counter Value,Reload Value of CPU/ABR" bitfld.byte 0x1 3. " FIDPE ,Enable for Parity Checking of Frame-ID" "Disabled,Enabled" textline " " bitfld.byte 0x1 2. " DBE ,Detection of Bus Error Enable" "Disabled,Enabled" bitfld.byte 0x1 1. " FIDE ,Frame-ID Register Enable" "Disabled,Enabled" bitfld.byte 0x1 0. " LBL2 ,MSB of LIN Break Length" "13-16,17-20" group.byte 0x1A++0x0 line.byte 0x0 "RFCR,Reception FIFO Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " RXFE_SET/CLR ,Reception FIFO Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " RXFCL ,Reception FIFO Clear" "Not reset,Reset" bitfld.byte 0x0 0.--4. " RXFLC ,Reception FIFO Level Configuration (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," group.byte 0x1B++0x0 line.byte 0x0 "TFCR,Transmission FIFO Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFE_SET/CLR ,Transmission FIFO Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " TXFCL ,Transmission FIFO Clear" "Not reset,Reset" bitfld.byte 0x0 0.--4. " TXFLC ,Transmission FIFO Level Configuration (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," wgroup.byte 0x1E++0x1 line.byte 0x0 "RFCCR,Reception FIFO Control Clear Register" bitfld.byte 0x0 6. " RXFCLC ,RXFCL Clear" "No effect,Clear" line.byte 0x1 "TFCCR,Transmission FIFO Control Clear Register" bitfld.byte 0x1 6. " TXFCLC ,TXFCL Clear" "No effect,Clear" group.byte 0x20++0x1 line.byte 0x0 "RFSR,Reception FIFO Status Register" bitfld.byte 0x0 0.--4. " RXFVD ,Reception FIFO Valid Data (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," line.byte 0x1 "TFSR,Transmission FIFO Status Register" bitfld.byte 0x1 0.--4. " TXFVD ,Transmission FIFO Valid Data (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," group.byte 0x22++0x0 "Checksum Register" line.byte 0x0 "CSCR,Checksum Status and Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " CRCERRIE_set/clr ,Checksum Error Interrupt Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " CCRCERR ,CRC Error Flag" "No error,Error" bitfld.byte 0x0 5. " CRCTYPE ,Checksum Type" "Classic,Enhanced" textline " " bitfld.byte 0x0 4. " CRCCHECK ,Checksum Verification Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " CRCGEN ,Checksum Generation Enable" "Disabled,Enabled" bitfld.byte 0x0 0.--2. " DL ,Data Length in LIN Frame (in bytes)" "1,2,3,4,5,6,7,8" wgroup.byte 0x26++0x0 line.byte 0x0 "CSCCR,Checksum Status and Control Clear Register" bitfld.byte 0x0 6. " CRCERRC ,CRCERR Clear" "No effect,Clear" rgroup.byte 0x23++0x0 "Status Register" line.byte 0x0 "ESR,Extended Status Register" bitfld.byte 0x0 6. " AD ,AD Status of Received Frame" "Usual data,Address" bitfld.byte 0x0 5. " TXHRI ,Transmission of Header" "Not completed,Completed" bitfld.byte 0x0 4. " RXHRI ,Reception of Header" "Not completed,Completed" textline " " bitfld.byte 0x0 3. " LBSOF ,Last Bit Shift Out Flag" "Not shifted out,Shifted out" bitfld.byte 0x0 2. " BUSERR ,Bus Error Flag" "No error,Error" bitfld.byte 0x0 1. " PEFRD ,Parity Error in Frame-ID" "No error,Error" textline " " bitfld.byte 0x0 0. " SYNFE ,Sync Field Error Flag" "No error,Error" wgroup.byte 0x27++0x0 line.byte 0x0 "ESCLR,Extended Status Clear Register" bitfld.byte 0x00 5. " TXHRIC ,TXHRI Clear" "No effect,Clear" bitfld.byte 0x00 4. " RXHRIC ,RXHRI Clear" "No effect,Clear" bitfld.byte 0x00 3. " LBSOFC ,LBSOF Clear" "No effect,Clear" textline " " bitfld.byte 0x00 2. " BUSERRC ,BUSERR Clear" "No effect,Clear" bitfld.byte 0x00 1. " PEFRDC ,PEFRD Clear" "No effect,Clear" bitfld.byte 0x00 0. " SYNFEC ,SYNFEC Clear" "No effect,Clear" wgroup.byte 0x28++0x2 "Baud Rate Registers" line.byte 0x0 "BGRLL,Baud Rate Generation Reload Register - L (bits[7:0])" line.byte 0x1 "BGRLM,Baud Rate Generation Reload Register - M (bits[15:8])" line.byte 0x2 "BGRLH,Baud Rate Generation Reload Register - H (bits[18:16])" bitfld.byte 0x2 0.--2. " Value[18:16] ,Baud Rate Generation Reload Register - H bits 16..18" "0,1,2,3,4,5,6,7" rgroup.byte 0x2C++0x2 line.byte 0x0 "BGRL,Baud Rate Generation Register - L (bits[0:7])" line.byte 0x1 "BGRM,Baud Rate Generation Register - M (bits[8:15])" line.byte 0x2 "BGRH,Baud Rate Generation Register - H (bits[16:18])" bitfld.byte 0x2 0.--2. " Value[18:16] ,Baud Rate Generation Register - H bits 16..18" "0,1,2,3,4,5,6,7" group.byte 0x30++0x00 "DMA Configuration Registers" line.byte 0x0 "STXDR,Serial Transmit DMA Configuration Register" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " TXDISDOERR_SET/CLR ,TX-DMA Request Mask/Disable" "No,Yes" setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " TXDRQEN_SET/CLR ,TX-DMA Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXDDEN_SET/CLR ,TX-DMA Demand Transfer Enable" "Disabled,Enabled" group.byte 0x31++0x00 line.byte 0x0 "SRXDR,Serial Receive DMA Configuration Register" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " RXDISDOERR_SET/CLR ,RX-DMA Request Mask/Disable" "No,Yes" setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXDRQEN_SET/CLR ,RX-DMA Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " RXDDEN_SET/CLR ,RX-DMA Demand Transfer Enable" "Disabled,Enabled" group.byte 0x36++0x02 "Sync Field Timeout Registers" line.byte 0x00 "SFTRL,Sync Field Timeout Register - L (bits[7:0])" line.byte 0x01 "SFTRM,Sync Field Timeout Register - M (bits[15:8])" line.byte 0x02 "SFTRH,Sync Field Timeout Register - H (bits[18:16])" bitfld.byte 0x02 0.--2. " VALUE[18:16] ,Sync Field Timeout Register - H bits 16..18" "0,1,2,3,4,5,6,7" group.byte 0x3A++0x0 "Frame-ID and Debug Register" line.byte 0x0 "FIDR,Frame-ID Register" sif (cpu()!="MB86R11F") group.byte 0x3C++0x0 line.byte 0x0 "DEBUG,Debug Register" bitfld.byte 0x0 0. " DBGEN ,Debug Enable" "Disabled,Enabled" endif width 12. tree.end tree "USART_2" base ad:0x3F020000 width 14. group.byte 0x00++0x00 "Mode and Control Registers" line.byte 0x00 "SMR,Serial Mode Register" bitfld.byte 0x0 6.--7. " MD ,Operation Mode Select" "Asynchronous normal,Asynchronous multiprocessor,Synchronous,Asynchronous LIN" bitfld.byte 0x0 5. " OTO ,One-to-One External Clock Selection" "Reload counter,External clock" bitfld.byte 0x0 4. " EXT ,External Clock Selection" "Reload counter,External clock" textline " " bitfld.byte 0x0 3. " REST ,Restart of Transmission Reload Counter" "No reset,Restart" bitfld.byte 0x0 2. " UPCL ,LIN-USART Programmable Clear" "No reset,Reset" if ((((per.b(ad:0x3F020000))&0xC0)==0x00)||(((per.b(ad:0x3F020000))&0xC0)==0x80)&&(((per.b(ad:0x3F020000+0x0C))&0x08)==0x08)) group.byte 0x01++0x00 line.byte 0x0 "SCR,Serial Control Register" bitfld.byte 0x0 7. " PEN ,Parity Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " P ,Parity Selection" "Even,Odd" bitfld.byte 0x0 5. " SBL ,Stop Bit Length Selection" "1,2" textline " " bitfld.byte 0x0 4. " CL ,Character (Data frame) Length (in bits)" "7,8" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " AD_SET/CLR ,Address or Data Selection" "Data,Address" bitfld.byte 0x0 2. " CRE ,Clear Reception Error Flags" "No effect,Clear" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXE_SET/CLR ,Reception Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXE_SET/CLR ,Transmission Enable" "Disabled,Enabled" else group.byte 0x01++0x00 line.byte 0x0 "SCR,Serial Control Register" bitfld.byte 0x0 6. " P ,Parity Selection" "Even,Odd" bitfld.byte 0x0 5. " SBL ,Stop Bit Length Selection" "1,2" textline " " bitfld.byte 0x0 4. " CL ,Character (Data frame) Length (in bits)" "7,8" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " AD_SET/CLR ,Address or Data Selection" "Data,Address" bitfld.byte 0x0 2. " CRE ,Clear Reception Error Flags" "No effect,Clear" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXE_SET/CLR ,Reception Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXE_SET/CLR ,Transmission Enable" "Disabled,Enabled" endif wgroup.byte 0x2++0x1 line.byte 0x0 "SMSR,Serial Mode Set Register" bitfld.byte 0x0 3. " RESTS ,REST Set" "No effect,Set" bitfld.byte 0x0 2. " UPCLS ,UPCL Set" "No effect,Set" line.byte 0x1 "SCSR,Serial Control Set Register" bitfld.byte 0x1 2. " CRES ,CRE Set" "No effect,Set" wgroup.byte 0x06++0x0 "Transmission Data Register" line.byte 0x0 "TDR,Transmission Data Register" hexmask.byte 0x0 0.--7. 1. " D[7:0] ,Transmission data" group.byte 0x07++0x0 "Status Register" line.byte 0x0 "SSR,Serial Status Register" rbitfld.byte 0x0 7. " PE ,Parity Error Flag" "No error,Error" rbitfld.byte 0x0 6. " ORE ,Overrun Error Flag" "No error,Error" rbitfld.byte 0x0 5. " FRE ,Framing Error Flag" "No error,Error" textline " " rbitfld.byte 0x0 4. " RDRF ,Receive Data Register Full Flag" "Empty,Full" bitfld.byte 0x0 3. " TDRE ,Transmission Data Register Empty" "Full,Empty" bitfld.byte 0x0 2. " BDS ,Transfer Direction Selection" "LSB,MSB" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RIE_SET/CLR ,Receive Interrupt Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TIE_SET/CLR ,Transmission Interrupt Request Enable" "Disabled,Enabled" hgroup.byte 0x08++0x00 "Reception Data Register" hide.byte 0x0 "RDR,Reception Data Register" in if ((((per.b(ad:0x3F020000+0x0C))&0x20)==0x20)&&(((per.b(ad:0x3F020000))&0xC0)==0x80)) group.byte 0x0C++0x00 "Extended Registers" line.byte 0x0 "ECCR,Extended Communication Control Register" bitfld.byte 0x0 7. " INV ,Invert Serial Data" "Not inverted,Inverted" bitfld.byte 0x0 6. " LBR ,Generate LIN Sync Break" "Ignored,Generated" bitfld.byte 0x0 5. " MS ,Master Slave Mode select" "Master mode,Slave mode" textline " " bitfld.byte 0x0 4. " SCDE ,Serial Clock Delay Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " SSM ,Start_Stop Bit Mode Enable" "Disabled,Enabled" else group.byte 0x0C++0x00 "Extended Registers" line.byte 0x0 "ECCR,Extended Communication Control Register" bitfld.byte 0x0 7. " INV ,Invert Serial Data" "Not inverted,Inverted" bitfld.byte 0x0 6. " LBR ,Generate LIN Sync Break" "Ignored,Generated" bitfld.byte 0x0 5. " MS ,Master Slave Mode select" "Master mode,Slave mode" textline " " bitfld.byte 0x0 4. " SCDE ,Serial Clock Delay Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " SSM ,Start_Stop Bit Mode Enable" "Disabled,Enabled" bitfld.byte 0x0 2. " BIE ,Bus Idle Interrupt Enable" "Disabled,Enabled" textline " " rbitfld.byte 0x0 1. " RBI ,Reception Bus Idle Flag" "Reception,No reception" rbitfld.byte 0x0 0. " TBI ,Transmission Bus Idle Flag" "Transmission,No transmission" endif if (((per.b(ad:0x3F020000+0x19))&0x1)==0x0) group.byte 0x0D++0x00 line.byte 0x0 "ESCR,Extended Status/Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " LBIE_SET/CLR ,LIN Sync Break Detection Interrupt Enable" "Disabled,Enabled" rbitfld.byte 0x0 6. " LBD ,Sync Break Detected Flag" "Not detected,Detected" bitfld.byte 0x0 4.--5. " LBL ,LIN Sync Break Length Selection (in bit times)" "13,14,15,16" textline " " bitfld.byte 0x0 3. " SOPE ,Serial Output Pin Direct Access Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " SOIP_SET/CLR ,Serial Input Output Pin Direct Access" "Low,High" bitfld.byte 0x0 1. " CCO ,Continuous Clock Output Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " SCES ,Serial Clock Edge Select" "Rising edge,Falling edge" else group.byte 0x0D++0x00 line.byte 0x0 "ESCR,Extended Status/Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " LBIE_SET/CLR ,LIN Sync Break Detection Interrupt Enable" "Disabled,Enabled" rbitfld.byte 0x0 6. " LBD ,Sync Break Detected Flag" "Not detected,Detected" bitfld.byte 0x0 4.--5. " LBL ,LIN Sync Break Length Selection (in bit times)" "17,18,19,20" textline " " bitfld.byte 0x0 3. " SOPE ,Serial Output Pin Direct Access Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " SOIP_SET/CLR ,Serial Input Output Pin Direct Access" "Low,High" bitfld.byte 0x0 1. " CCO ,Continuous Clock Output Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " SCES ,Serial Clock Edge Select" "Rising edge,Falling edge" endif group.byte 0x0E++0x00 line.byte 0x0 "ECCSR,Extended Communication Control Set Register" bitfld.byte 0x0 6. " LBRS ,LBR Set" "No effect,Set" bitfld.byte 0x0 2. " BIES ,BIE Set" "No effect,Set" group.byte 0x10++0x01 line.byte 0x00 "ECCCR,Extended Communication Control Clear Register" bitfld.byte 0x0 2. " BIEC ,BIE Clear" "No effect,Clear" line.byte 0x01 "ESCCR,Extended Status/Control Clear Register" bitfld.byte 0x1 6. " LBDC ,LBD Clear" "No effect,Clear" group.byte 0x12++0x00 line.byte 0x0 "ESIR,Extended Serial Interrupt Register" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " PEIE_SET/CLR ,Parity Error (in data received) Interrupt Enable bit" "Disabled,Enabled" setclrfld.byte 0x0 5. 0x2 5. 0x4 5. " OREIE_SET/CLR ,Overrun Error Interrupt Enable bit" "Disabled,Enabled" setclrfld.byte 0x0 4. 0x2 4. 0x4 4. " FREIE_SET/CLR ,Framing Error Interrupt Enable bit" "Disabled,Enabled" textline " " bitfld.byte 0x0 3. " TDRE ,Transmission Data Register Empty (Sticky Behaviour)" "Full,Empty" bitfld.byte 0x0 2. " RDRF ,Reception Data Register Full (Sticky Behaviour)" "Empty,Full" bitfld.byte 0x0 1. " RBI ,Reception Bus Idle (Sticky Behaviour)" "Reception,No reception" textline " " bitfld.byte 0x0 0. " AICD ,Auto Interrupt Clear Disable" "Enabled,Disabled" if (((per.b(ad:0x3F020000))&0xC0)==0xC0) group.byte 0x13++0x0 line.byte 0x0 "EIER,Extended Interrupt Enable Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFIE_SET/CLR ,Transmission FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " RXFIE_SET/CLR ,Reception FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 5. 0x2 5. 0x4 5. " SYNFEIE_SET/CLR ,Sync Field Error Interrupt Enable" "Disabled,Enabled" textline " " setclrfld.byte 0x0 4. 0x2 4. 0x4 4. " RXHDIE_SET/CLR ,Reception Header Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " TXHDIE_SET/CLR ,Transmission Header Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " PEFRDIE_SET/CLR ,Parity Error in Frame-ID Received Interrupt Enable" "Disabled,Enabled" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " BUSERRIE_SET/CLR ,Bus Error Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " LBSOIE_SET/CLR ,BLast Bit Shifted Out Interrupt Enable bit" "Disabled,Enabled" else group.byte 0x13++0x0 line.byte 0x0 "EIER,Extended Interrupt Enable Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFIE_SET/CLR ,Transmission FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " RXFIE_SET/CLR ,Reception FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " LBSOIE_SET/CLR ,BLast Bit Shifted Out Interrupt Enable bit" "Disabled,Enabled" endif wgroup.byte 0x16++0x0 line.byte 0x0 "ESICR,Extended Serial Interrupt Clear Register" bitfld.byte 0x0 3. " TDREC ,Transmission Data Register Empty Flag (TDRE) Clear" "No effect,Clear" bitfld.byte 0x0 2. " RDRFC ,Reception Data Register Full Flag (RDRF) Clear" "No effect,Clear" bitfld.byte 0x0 1. " RBIC ,Reception Bus Idle Flag (RBI) Clear" "No effect,Clear" group.byte 0x18++0x1 line.byte 0x0 "EFERL,Extended Feature Enable Register - L" bitfld.byte 0x0 6. " OSDE ,Oversampling Disable" "No,Yes" bitfld.byte 0x0 5. " DTSTART ,Detect Start bit" "Low level,Falling edge" bitfld.byte 0x0 4. " RSTRFM ,Reset Reception State Machine" "Enabled,Disabled" textline " " bitfld.byte 0x0 3. " LBEDGE ,LIN Break Edge Sensitive" "Level,Edge" bitfld.byte 0x0 2. " ABRE ,Auto Baud Rate Detection/Adjustment Enable" "Disabled,Enabled" bitfld.byte 0x0 1. " ENRXHR ,Automatic Header Detection Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " ENTXHR ,Automatic Header Transmission Enable" "Disabled,Enabled" line.byte 0x1 "EFERH,Extended Feature Enable Register - H" bitfld.byte 0x1 5. " INTLBEN ,Internal Loop Back Enable" "Disabled,Enabled" bitfld.byte 0x1 4. " BRGR ,Baud Rate Regiter Read" "Reload Counter Value,Reload Value of CPU/ABR" bitfld.byte 0x1 3. " FIDPE ,Enable for Parity Checking of Frame-ID" "Disabled,Enabled" textline " " bitfld.byte 0x1 2. " DBE ,Detection of Bus Error Enable" "Disabled,Enabled" bitfld.byte 0x1 1. " FIDE ,Frame-ID Register Enable" "Disabled,Enabled" bitfld.byte 0x1 0. " LBL2 ,MSB of LIN Break Length" "13-16,17-20" group.byte 0x1A++0x0 line.byte 0x0 "RFCR,Reception FIFO Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " RXFE_SET/CLR ,Reception FIFO Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " RXFCL ,Reception FIFO Clear" "Not reset,Reset" bitfld.byte 0x0 0.--4. " RXFLC ,Reception FIFO Level Configuration (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," group.byte 0x1B++0x0 line.byte 0x0 "TFCR,Transmission FIFO Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFE_SET/CLR ,Transmission FIFO Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " TXFCL ,Transmission FIFO Clear" "Not reset,Reset" bitfld.byte 0x0 0.--4. " TXFLC ,Transmission FIFO Level Configuration (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," wgroup.byte 0x1E++0x1 line.byte 0x0 "RFCCR,Reception FIFO Control Clear Register" bitfld.byte 0x0 6. " RXFCLC ,RXFCL Clear" "No effect,Clear" line.byte 0x1 "TFCCR,Transmission FIFO Control Clear Register" bitfld.byte 0x1 6. " TXFCLC ,TXFCL Clear" "No effect,Clear" group.byte 0x20++0x1 line.byte 0x0 "RFSR,Reception FIFO Status Register" bitfld.byte 0x0 0.--4. " RXFVD ,Reception FIFO Valid Data (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," line.byte 0x1 "TFSR,Transmission FIFO Status Register" bitfld.byte 0x1 0.--4. " TXFVD ,Transmission FIFO Valid Data (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," group.byte 0x22++0x0 "Checksum Register" line.byte 0x0 "CSCR,Checksum Status and Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " CRCERRIE_set/clr ,Checksum Error Interrupt Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " CCRCERR ,CRC Error Flag" "No error,Error" bitfld.byte 0x0 5. " CRCTYPE ,Checksum Type" "Classic,Enhanced" textline " " bitfld.byte 0x0 4. " CRCCHECK ,Checksum Verification Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " CRCGEN ,Checksum Generation Enable" "Disabled,Enabled" bitfld.byte 0x0 0.--2. " DL ,Data Length in LIN Frame (in bytes)" "1,2,3,4,5,6,7,8" wgroup.byte 0x26++0x0 line.byte 0x0 "CSCCR,Checksum Status and Control Clear Register" bitfld.byte 0x0 6. " CRCERRC ,CRCERR Clear" "No effect,Clear" rgroup.byte 0x23++0x0 "Status Register" line.byte 0x0 "ESR,Extended Status Register" bitfld.byte 0x0 6. " AD ,AD Status of Received Frame" "Usual data,Address" bitfld.byte 0x0 5. " TXHRI ,Transmission of Header" "Not completed,Completed" bitfld.byte 0x0 4. " RXHRI ,Reception of Header" "Not completed,Completed" textline " " bitfld.byte 0x0 3. " LBSOF ,Last Bit Shift Out Flag" "Not shifted out,Shifted out" bitfld.byte 0x0 2. " BUSERR ,Bus Error Flag" "No error,Error" bitfld.byte 0x0 1. " PEFRD ,Parity Error in Frame-ID" "No error,Error" textline " " bitfld.byte 0x0 0. " SYNFE ,Sync Field Error Flag" "No error,Error" wgroup.byte 0x27++0x0 line.byte 0x0 "ESCLR,Extended Status Clear Register" bitfld.byte 0x00 5. " TXHRIC ,TXHRI Clear" "No effect,Clear" bitfld.byte 0x00 4. " RXHRIC ,RXHRI Clear" "No effect,Clear" bitfld.byte 0x00 3. " LBSOFC ,LBSOF Clear" "No effect,Clear" textline " " bitfld.byte 0x00 2. " BUSERRC ,BUSERR Clear" "No effect,Clear" bitfld.byte 0x00 1. " PEFRDC ,PEFRD Clear" "No effect,Clear" bitfld.byte 0x00 0. " SYNFEC ,SYNFEC Clear" "No effect,Clear" wgroup.byte 0x28++0x2 "Baud Rate Registers" line.byte 0x0 "BGRLL,Baud Rate Generation Reload Register - L (bits[7:0])" line.byte 0x1 "BGRLM,Baud Rate Generation Reload Register - M (bits[15:8])" line.byte 0x2 "BGRLH,Baud Rate Generation Reload Register - H (bits[18:16])" bitfld.byte 0x2 0.--2. " Value[18:16] ,Baud Rate Generation Reload Register - H bits 16..18" "0,1,2,3,4,5,6,7" rgroup.byte 0x2C++0x2 line.byte 0x0 "BGRL,Baud Rate Generation Register - L (bits[0:7])" line.byte 0x1 "BGRM,Baud Rate Generation Register - M (bits[8:15])" line.byte 0x2 "BGRH,Baud Rate Generation Register - H (bits[16:18])" bitfld.byte 0x2 0.--2. " Value[18:16] ,Baud Rate Generation Register - H bits 16..18" "0,1,2,3,4,5,6,7" group.byte 0x30++0x00 "DMA Configuration Registers" line.byte 0x0 "STXDR,Serial Transmit DMA Configuration Register" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " TXDISDOERR_SET/CLR ,TX-DMA Request Mask/Disable" "No,Yes" setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " TXDRQEN_SET/CLR ,TX-DMA Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXDDEN_SET/CLR ,TX-DMA Demand Transfer Enable" "Disabled,Enabled" group.byte 0x31++0x00 line.byte 0x0 "SRXDR,Serial Receive DMA Configuration Register" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " RXDISDOERR_SET/CLR ,RX-DMA Request Mask/Disable" "No,Yes" setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXDRQEN_SET/CLR ,RX-DMA Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " RXDDEN_SET/CLR ,RX-DMA Demand Transfer Enable" "Disabled,Enabled" group.byte 0x36++0x02 "Sync Field Timeout Registers" line.byte 0x00 "SFTRL,Sync Field Timeout Register - L (bits[7:0])" line.byte 0x01 "SFTRM,Sync Field Timeout Register - M (bits[15:8])" line.byte 0x02 "SFTRH,Sync Field Timeout Register - H (bits[18:16])" bitfld.byte 0x02 0.--2. " VALUE[18:16] ,Sync Field Timeout Register - H bits 16..18" "0,1,2,3,4,5,6,7" group.byte 0x3A++0x0 "Frame-ID and Debug Register" line.byte 0x0 "FIDR,Frame-ID Register" sif (cpu()!="MB86R11F") group.byte 0x3C++0x0 line.byte 0x0 "DEBUG,Debug Register" bitfld.byte 0x0 0. " DBGEN ,Debug Enable" "Disabled,Enabled" endif width 12. tree.end tree "USART_3" base ad:0x3F030000 width 14. group.byte 0x00++0x00 "Mode and Control Registers" line.byte 0x00 "SMR,Serial Mode Register" bitfld.byte 0x0 6.--7. " MD ,Operation Mode Select" "Asynchronous normal,Asynchronous multiprocessor,Synchronous,Asynchronous LIN" bitfld.byte 0x0 5. " OTO ,One-to-One External Clock Selection" "Reload counter,External clock" bitfld.byte 0x0 4. " EXT ,External Clock Selection" "Reload counter,External clock" textline " " bitfld.byte 0x0 3. " REST ,Restart of Transmission Reload Counter" "No reset,Restart" bitfld.byte 0x0 2. " UPCL ,LIN-USART Programmable Clear" "No reset,Reset" if ((((per.b(ad:0x3F030000))&0xC0)==0x00)||(((per.b(ad:0x3F030000))&0xC0)==0x80)&&(((per.b(ad:0x3F030000+0x0C))&0x08)==0x08)) group.byte 0x01++0x00 line.byte 0x0 "SCR,Serial Control Register" bitfld.byte 0x0 7. " PEN ,Parity Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " P ,Parity Selection" "Even,Odd" bitfld.byte 0x0 5. " SBL ,Stop Bit Length Selection" "1,2" textline " " bitfld.byte 0x0 4. " CL ,Character (Data frame) Length (in bits)" "7,8" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " AD_SET/CLR ,Address or Data Selection" "Data,Address" bitfld.byte 0x0 2. " CRE ,Clear Reception Error Flags" "No effect,Clear" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXE_SET/CLR ,Reception Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXE_SET/CLR ,Transmission Enable" "Disabled,Enabled" else group.byte 0x01++0x00 line.byte 0x0 "SCR,Serial Control Register" bitfld.byte 0x0 6. " P ,Parity Selection" "Even,Odd" bitfld.byte 0x0 5. " SBL ,Stop Bit Length Selection" "1,2" textline " " bitfld.byte 0x0 4. " CL ,Character (Data frame) Length (in bits)" "7,8" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " AD_SET/CLR ,Address or Data Selection" "Data,Address" bitfld.byte 0x0 2. " CRE ,Clear Reception Error Flags" "No effect,Clear" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXE_SET/CLR ,Reception Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXE_SET/CLR ,Transmission Enable" "Disabled,Enabled" endif wgroup.byte 0x2++0x1 line.byte 0x0 "SMSR,Serial Mode Set Register" bitfld.byte 0x0 3. " RESTS ,REST Set" "No effect,Set" bitfld.byte 0x0 2. " UPCLS ,UPCL Set" "No effect,Set" line.byte 0x1 "SCSR,Serial Control Set Register" bitfld.byte 0x1 2. " CRES ,CRE Set" "No effect,Set" wgroup.byte 0x06++0x0 "Transmission Data Register" line.byte 0x0 "TDR,Transmission Data Register" hexmask.byte 0x0 0.--7. 1. " D[7:0] ,Transmission data" group.byte 0x07++0x0 "Status Register" line.byte 0x0 "SSR,Serial Status Register" rbitfld.byte 0x0 7. " PE ,Parity Error Flag" "No error,Error" rbitfld.byte 0x0 6. " ORE ,Overrun Error Flag" "No error,Error" rbitfld.byte 0x0 5. " FRE ,Framing Error Flag" "No error,Error" textline " " rbitfld.byte 0x0 4. " RDRF ,Receive Data Register Full Flag" "Empty,Full" bitfld.byte 0x0 3. " TDRE ,Transmission Data Register Empty" "Full,Empty" bitfld.byte 0x0 2. " BDS ,Transfer Direction Selection" "LSB,MSB" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RIE_SET/CLR ,Receive Interrupt Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TIE_SET/CLR ,Transmission Interrupt Request Enable" "Disabled,Enabled" hgroup.byte 0x08++0x00 "Reception Data Register" hide.byte 0x0 "RDR,Reception Data Register" in if ((((per.b(ad:0x3F030000+0x0C))&0x20)==0x20)&&(((per.b(ad:0x3F030000))&0xC0)==0x80)) group.byte 0x0C++0x00 "Extended Registers" line.byte 0x0 "ECCR,Extended Communication Control Register" bitfld.byte 0x0 7. " INV ,Invert Serial Data" "Not inverted,Inverted" bitfld.byte 0x0 6. " LBR ,Generate LIN Sync Break" "Ignored,Generated" bitfld.byte 0x0 5. " MS ,Master Slave Mode select" "Master mode,Slave mode" textline " " bitfld.byte 0x0 4. " SCDE ,Serial Clock Delay Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " SSM ,Start_Stop Bit Mode Enable" "Disabled,Enabled" else group.byte 0x0C++0x00 "Extended Registers" line.byte 0x0 "ECCR,Extended Communication Control Register" bitfld.byte 0x0 7. " INV ,Invert Serial Data" "Not inverted,Inverted" bitfld.byte 0x0 6. " LBR ,Generate LIN Sync Break" "Ignored,Generated" bitfld.byte 0x0 5. " MS ,Master Slave Mode select" "Master mode,Slave mode" textline " " bitfld.byte 0x0 4. " SCDE ,Serial Clock Delay Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " SSM ,Start_Stop Bit Mode Enable" "Disabled,Enabled" bitfld.byte 0x0 2. " BIE ,Bus Idle Interrupt Enable" "Disabled,Enabled" textline " " rbitfld.byte 0x0 1. " RBI ,Reception Bus Idle Flag" "Reception,No reception" rbitfld.byte 0x0 0. " TBI ,Transmission Bus Idle Flag" "Transmission,No transmission" endif if (((per.b(ad:0x3F030000+0x19))&0x1)==0x0) group.byte 0x0D++0x00 line.byte 0x0 "ESCR,Extended Status/Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " LBIE_SET/CLR ,LIN Sync Break Detection Interrupt Enable" "Disabled,Enabled" rbitfld.byte 0x0 6. " LBD ,Sync Break Detected Flag" "Not detected,Detected" bitfld.byte 0x0 4.--5. " LBL ,LIN Sync Break Length Selection (in bit times)" "13,14,15,16" textline " " bitfld.byte 0x0 3. " SOPE ,Serial Output Pin Direct Access Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " SOIP_SET/CLR ,Serial Input Output Pin Direct Access" "Low,High" bitfld.byte 0x0 1. " CCO ,Continuous Clock Output Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " SCES ,Serial Clock Edge Select" "Rising edge,Falling edge" else group.byte 0x0D++0x00 line.byte 0x0 "ESCR,Extended Status/Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " LBIE_SET/CLR ,LIN Sync Break Detection Interrupt Enable" "Disabled,Enabled" rbitfld.byte 0x0 6. " LBD ,Sync Break Detected Flag" "Not detected,Detected" bitfld.byte 0x0 4.--5. " LBL ,LIN Sync Break Length Selection (in bit times)" "17,18,19,20" textline " " bitfld.byte 0x0 3. " SOPE ,Serial Output Pin Direct Access Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " SOIP_SET/CLR ,Serial Input Output Pin Direct Access" "Low,High" bitfld.byte 0x0 1. " CCO ,Continuous Clock Output Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " SCES ,Serial Clock Edge Select" "Rising edge,Falling edge" endif group.byte 0x0E++0x00 line.byte 0x0 "ECCSR,Extended Communication Control Set Register" bitfld.byte 0x0 6. " LBRS ,LBR Set" "No effect,Set" bitfld.byte 0x0 2. " BIES ,BIE Set" "No effect,Set" group.byte 0x10++0x01 line.byte 0x00 "ECCCR,Extended Communication Control Clear Register" bitfld.byte 0x0 2. " BIEC ,BIE Clear" "No effect,Clear" line.byte 0x01 "ESCCR,Extended Status/Control Clear Register" bitfld.byte 0x1 6. " LBDC ,LBD Clear" "No effect,Clear" group.byte 0x12++0x00 line.byte 0x0 "ESIR,Extended Serial Interrupt Register" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " PEIE_SET/CLR ,Parity Error (in data received) Interrupt Enable bit" "Disabled,Enabled" setclrfld.byte 0x0 5. 0x2 5. 0x4 5. " OREIE_SET/CLR ,Overrun Error Interrupt Enable bit" "Disabled,Enabled" setclrfld.byte 0x0 4. 0x2 4. 0x4 4. " FREIE_SET/CLR ,Framing Error Interrupt Enable bit" "Disabled,Enabled" textline " " bitfld.byte 0x0 3. " TDRE ,Transmission Data Register Empty (Sticky Behaviour)" "Full,Empty" bitfld.byte 0x0 2. " RDRF ,Reception Data Register Full (Sticky Behaviour)" "Empty,Full" bitfld.byte 0x0 1. " RBI ,Reception Bus Idle (Sticky Behaviour)" "Reception,No reception" textline " " bitfld.byte 0x0 0. " AICD ,Auto Interrupt Clear Disable" "Enabled,Disabled" if (((per.b(ad:0x3F030000))&0xC0)==0xC0) group.byte 0x13++0x0 line.byte 0x0 "EIER,Extended Interrupt Enable Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFIE_SET/CLR ,Transmission FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " RXFIE_SET/CLR ,Reception FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 5. 0x2 5. 0x4 5. " SYNFEIE_SET/CLR ,Sync Field Error Interrupt Enable" "Disabled,Enabled" textline " " setclrfld.byte 0x0 4. 0x2 4. 0x4 4. " RXHDIE_SET/CLR ,Reception Header Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " TXHDIE_SET/CLR ,Transmission Header Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " PEFRDIE_SET/CLR ,Parity Error in Frame-ID Received Interrupt Enable" "Disabled,Enabled" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " BUSERRIE_SET/CLR ,Bus Error Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " LBSOIE_SET/CLR ,BLast Bit Shifted Out Interrupt Enable bit" "Disabled,Enabled" else group.byte 0x13++0x0 line.byte 0x0 "EIER,Extended Interrupt Enable Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFIE_SET/CLR ,Transmission FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " RXFIE_SET/CLR ,Reception FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " LBSOIE_SET/CLR ,BLast Bit Shifted Out Interrupt Enable bit" "Disabled,Enabled" endif wgroup.byte 0x16++0x0 line.byte 0x0 "ESICR,Extended Serial Interrupt Clear Register" bitfld.byte 0x0 3. " TDREC ,Transmission Data Register Empty Flag (TDRE) Clear" "No effect,Clear" bitfld.byte 0x0 2. " RDRFC ,Reception Data Register Full Flag (RDRF) Clear" "No effect,Clear" bitfld.byte 0x0 1. " RBIC ,Reception Bus Idle Flag (RBI) Clear" "No effect,Clear" group.byte 0x18++0x1 line.byte 0x0 "EFERL,Extended Feature Enable Register - L" bitfld.byte 0x0 6. " OSDE ,Oversampling Disable" "No,Yes" bitfld.byte 0x0 5. " DTSTART ,Detect Start bit" "Low level,Falling edge" bitfld.byte 0x0 4. " RSTRFM ,Reset Reception State Machine" "Enabled,Disabled" textline " " bitfld.byte 0x0 3. " LBEDGE ,LIN Break Edge Sensitive" "Level,Edge" bitfld.byte 0x0 2. " ABRE ,Auto Baud Rate Detection/Adjustment Enable" "Disabled,Enabled" bitfld.byte 0x0 1. " ENRXHR ,Automatic Header Detection Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " ENTXHR ,Automatic Header Transmission Enable" "Disabled,Enabled" line.byte 0x1 "EFERH,Extended Feature Enable Register - H" bitfld.byte 0x1 5. " INTLBEN ,Internal Loop Back Enable" "Disabled,Enabled" bitfld.byte 0x1 4. " BRGR ,Baud Rate Regiter Read" "Reload Counter Value,Reload Value of CPU/ABR" bitfld.byte 0x1 3. " FIDPE ,Enable for Parity Checking of Frame-ID" "Disabled,Enabled" textline " " bitfld.byte 0x1 2. " DBE ,Detection of Bus Error Enable" "Disabled,Enabled" bitfld.byte 0x1 1. " FIDE ,Frame-ID Register Enable" "Disabled,Enabled" bitfld.byte 0x1 0. " LBL2 ,MSB of LIN Break Length" "13-16,17-20" group.byte 0x1A++0x0 line.byte 0x0 "RFCR,Reception FIFO Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " RXFE_SET/CLR ,Reception FIFO Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " RXFCL ,Reception FIFO Clear" "Not reset,Reset" bitfld.byte 0x0 0.--4. " RXFLC ,Reception FIFO Level Configuration (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," group.byte 0x1B++0x0 line.byte 0x0 "TFCR,Transmission FIFO Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFE_SET/CLR ,Transmission FIFO Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " TXFCL ,Transmission FIFO Clear" "Not reset,Reset" bitfld.byte 0x0 0.--4. " TXFLC ,Transmission FIFO Level Configuration (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," wgroup.byte 0x1E++0x1 line.byte 0x0 "RFCCR,Reception FIFO Control Clear Register" bitfld.byte 0x0 6. " RXFCLC ,RXFCL Clear" "No effect,Clear" line.byte 0x1 "TFCCR,Transmission FIFO Control Clear Register" bitfld.byte 0x1 6. " TXFCLC ,TXFCL Clear" "No effect,Clear" group.byte 0x20++0x1 line.byte 0x0 "RFSR,Reception FIFO Status Register" bitfld.byte 0x0 0.--4. " RXFVD ,Reception FIFO Valid Data (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," line.byte 0x1 "TFSR,Transmission FIFO Status Register" bitfld.byte 0x1 0.--4. " TXFVD ,Transmission FIFO Valid Data (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," group.byte 0x22++0x0 "Checksum Register" line.byte 0x0 "CSCR,Checksum Status and Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " CRCERRIE_set/clr ,Checksum Error Interrupt Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " CCRCERR ,CRC Error Flag" "No error,Error" bitfld.byte 0x0 5. " CRCTYPE ,Checksum Type" "Classic,Enhanced" textline " " bitfld.byte 0x0 4. " CRCCHECK ,Checksum Verification Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " CRCGEN ,Checksum Generation Enable" "Disabled,Enabled" bitfld.byte 0x0 0.--2. " DL ,Data Length in LIN Frame (in bytes)" "1,2,3,4,5,6,7,8" wgroup.byte 0x26++0x0 line.byte 0x0 "CSCCR,Checksum Status and Control Clear Register" bitfld.byte 0x0 6. " CRCERRC ,CRCERR Clear" "No effect,Clear" rgroup.byte 0x23++0x0 "Status Register" line.byte 0x0 "ESR,Extended Status Register" bitfld.byte 0x0 6. " AD ,AD Status of Received Frame" "Usual data,Address" bitfld.byte 0x0 5. " TXHRI ,Transmission of Header" "Not completed,Completed" bitfld.byte 0x0 4. " RXHRI ,Reception of Header" "Not completed,Completed" textline " " bitfld.byte 0x0 3. " LBSOF ,Last Bit Shift Out Flag" "Not shifted out,Shifted out" bitfld.byte 0x0 2. " BUSERR ,Bus Error Flag" "No error,Error" bitfld.byte 0x0 1. " PEFRD ,Parity Error in Frame-ID" "No error,Error" textline " " bitfld.byte 0x0 0. " SYNFE ,Sync Field Error Flag" "No error,Error" wgroup.byte 0x27++0x0 line.byte 0x0 "ESCLR,Extended Status Clear Register" bitfld.byte 0x00 5. " TXHRIC ,TXHRI Clear" "No effect,Clear" bitfld.byte 0x00 4. " RXHRIC ,RXHRI Clear" "No effect,Clear" bitfld.byte 0x00 3. " LBSOFC ,LBSOF Clear" "No effect,Clear" textline " " bitfld.byte 0x00 2. " BUSERRC ,BUSERR Clear" "No effect,Clear" bitfld.byte 0x00 1. " PEFRDC ,PEFRD Clear" "No effect,Clear" bitfld.byte 0x00 0. " SYNFEC ,SYNFEC Clear" "No effect,Clear" wgroup.byte 0x28++0x2 "Baud Rate Registers" line.byte 0x0 "BGRLL,Baud Rate Generation Reload Register - L (bits[7:0])" line.byte 0x1 "BGRLM,Baud Rate Generation Reload Register - M (bits[15:8])" line.byte 0x2 "BGRLH,Baud Rate Generation Reload Register - H (bits[18:16])" bitfld.byte 0x2 0.--2. " Value[18:16] ,Baud Rate Generation Reload Register - H bits 16..18" "0,1,2,3,4,5,6,7" rgroup.byte 0x2C++0x2 line.byte 0x0 "BGRL,Baud Rate Generation Register - L (bits[0:7])" line.byte 0x1 "BGRM,Baud Rate Generation Register - M (bits[8:15])" line.byte 0x2 "BGRH,Baud Rate Generation Register - H (bits[16:18])" bitfld.byte 0x2 0.--2. " Value[18:16] ,Baud Rate Generation Register - H bits 16..18" "0,1,2,3,4,5,6,7" group.byte 0x30++0x00 "DMA Configuration Registers" line.byte 0x0 "STXDR,Serial Transmit DMA Configuration Register" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " TXDISDOERR_SET/CLR ,TX-DMA Request Mask/Disable" "No,Yes" setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " TXDRQEN_SET/CLR ,TX-DMA Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXDDEN_SET/CLR ,TX-DMA Demand Transfer Enable" "Disabled,Enabled" group.byte 0x31++0x00 line.byte 0x0 "SRXDR,Serial Receive DMA Configuration Register" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " RXDISDOERR_SET/CLR ,RX-DMA Request Mask/Disable" "No,Yes" setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXDRQEN_SET/CLR ,RX-DMA Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " RXDDEN_SET/CLR ,RX-DMA Demand Transfer Enable" "Disabled,Enabled" group.byte 0x36++0x02 "Sync Field Timeout Registers" line.byte 0x00 "SFTRL,Sync Field Timeout Register - L (bits[7:0])" line.byte 0x01 "SFTRM,Sync Field Timeout Register - M (bits[15:8])" line.byte 0x02 "SFTRH,Sync Field Timeout Register - H (bits[18:16])" bitfld.byte 0x02 0.--2. " VALUE[18:16] ,Sync Field Timeout Register - H bits 16..18" "0,1,2,3,4,5,6,7" group.byte 0x3A++0x0 "Frame-ID and Debug Register" line.byte 0x0 "FIDR,Frame-ID Register" sif (cpu()!="MB86R11F") group.byte 0x3C++0x0 line.byte 0x0 "DEBUG,Debug Register" bitfld.byte 0x0 0. " DBGEN ,Debug Enable" "Disabled,Enabled" endif width 12. tree.end tree "USART_4" base ad:0x3F040000 width 14. group.byte 0x00++0x00 "Mode and Control Registers" line.byte 0x00 "SMR,Serial Mode Register" bitfld.byte 0x0 6.--7. " MD ,Operation Mode Select" "Asynchronous normal,Asynchronous multiprocessor,Synchronous,Asynchronous LIN" bitfld.byte 0x0 5. " OTO ,One-to-One External Clock Selection" "Reload counter,External clock" bitfld.byte 0x0 4. " EXT ,External Clock Selection" "Reload counter,External clock" textline " " bitfld.byte 0x0 3. " REST ,Restart of Transmission Reload Counter" "No reset,Restart" bitfld.byte 0x0 2. " UPCL ,LIN-USART Programmable Clear" "No reset,Reset" if ((((per.b(ad:0x3F040000))&0xC0)==0x00)||(((per.b(ad:0x3F040000))&0xC0)==0x80)&&(((per.b(ad:0x3F040000+0x0C))&0x08)==0x08)) group.byte 0x01++0x00 line.byte 0x0 "SCR,Serial Control Register" bitfld.byte 0x0 7. " PEN ,Parity Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " P ,Parity Selection" "Even,Odd" bitfld.byte 0x0 5. " SBL ,Stop Bit Length Selection" "1,2" textline " " bitfld.byte 0x0 4. " CL ,Character (Data frame) Length (in bits)" "7,8" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " AD_SET/CLR ,Address or Data Selection" "Data,Address" bitfld.byte 0x0 2. " CRE ,Clear Reception Error Flags" "No effect,Clear" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXE_SET/CLR ,Reception Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXE_SET/CLR ,Transmission Enable" "Disabled,Enabled" else group.byte 0x01++0x00 line.byte 0x0 "SCR,Serial Control Register" bitfld.byte 0x0 6. " P ,Parity Selection" "Even,Odd" bitfld.byte 0x0 5. " SBL ,Stop Bit Length Selection" "1,2" textline " " bitfld.byte 0x0 4. " CL ,Character (Data frame) Length (in bits)" "7,8" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " AD_SET/CLR ,Address or Data Selection" "Data,Address" bitfld.byte 0x0 2. " CRE ,Clear Reception Error Flags" "No effect,Clear" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXE_SET/CLR ,Reception Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXE_SET/CLR ,Transmission Enable" "Disabled,Enabled" endif wgroup.byte 0x2++0x1 line.byte 0x0 "SMSR,Serial Mode Set Register" bitfld.byte 0x0 3. " RESTS ,REST Set" "No effect,Set" bitfld.byte 0x0 2. " UPCLS ,UPCL Set" "No effect,Set" line.byte 0x1 "SCSR,Serial Control Set Register" bitfld.byte 0x1 2. " CRES ,CRE Set" "No effect,Set" wgroup.byte 0x06++0x0 "Transmission Data Register" line.byte 0x0 "TDR,Transmission Data Register" hexmask.byte 0x0 0.--7. 1. " D[7:0] ,Transmission data" group.byte 0x07++0x0 "Status Register" line.byte 0x0 "SSR,Serial Status Register" rbitfld.byte 0x0 7. " PE ,Parity Error Flag" "No error,Error" rbitfld.byte 0x0 6. " ORE ,Overrun Error Flag" "No error,Error" rbitfld.byte 0x0 5. " FRE ,Framing Error Flag" "No error,Error" textline " " rbitfld.byte 0x0 4. " RDRF ,Receive Data Register Full Flag" "Empty,Full" bitfld.byte 0x0 3. " TDRE ,Transmission Data Register Empty" "Full,Empty" bitfld.byte 0x0 2. " BDS ,Transfer Direction Selection" "LSB,MSB" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RIE_SET/CLR ,Receive Interrupt Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TIE_SET/CLR ,Transmission Interrupt Request Enable" "Disabled,Enabled" hgroup.byte 0x08++0x00 "Reception Data Register" hide.byte 0x0 "RDR,Reception Data Register" in if ((((per.b(ad:0x3F040000+0x0C))&0x20)==0x20)&&(((per.b(ad:0x3F040000))&0xC0)==0x80)) group.byte 0x0C++0x00 "Extended Registers" line.byte 0x0 "ECCR,Extended Communication Control Register" bitfld.byte 0x0 7. " INV ,Invert Serial Data" "Not inverted,Inverted" bitfld.byte 0x0 6. " LBR ,Generate LIN Sync Break" "Ignored,Generated" bitfld.byte 0x0 5. " MS ,Master Slave Mode select" "Master mode,Slave mode" textline " " bitfld.byte 0x0 4. " SCDE ,Serial Clock Delay Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " SSM ,Start_Stop Bit Mode Enable" "Disabled,Enabled" else group.byte 0x0C++0x00 "Extended Registers" line.byte 0x0 "ECCR,Extended Communication Control Register" bitfld.byte 0x0 7. " INV ,Invert Serial Data" "Not inverted,Inverted" bitfld.byte 0x0 6. " LBR ,Generate LIN Sync Break" "Ignored,Generated" bitfld.byte 0x0 5. " MS ,Master Slave Mode select" "Master mode,Slave mode" textline " " bitfld.byte 0x0 4. " SCDE ,Serial Clock Delay Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " SSM ,Start_Stop Bit Mode Enable" "Disabled,Enabled" bitfld.byte 0x0 2. " BIE ,Bus Idle Interrupt Enable" "Disabled,Enabled" textline " " rbitfld.byte 0x0 1. " RBI ,Reception Bus Idle Flag" "Reception,No reception" rbitfld.byte 0x0 0. " TBI ,Transmission Bus Idle Flag" "Transmission,No transmission" endif if (((per.b(ad:0x3F040000+0x19))&0x1)==0x0) group.byte 0x0D++0x00 line.byte 0x0 "ESCR,Extended Status/Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " LBIE_SET/CLR ,LIN Sync Break Detection Interrupt Enable" "Disabled,Enabled" rbitfld.byte 0x0 6. " LBD ,Sync Break Detected Flag" "Not detected,Detected" bitfld.byte 0x0 4.--5. " LBL ,LIN Sync Break Length Selection (in bit times)" "13,14,15,16" textline " " bitfld.byte 0x0 3. " SOPE ,Serial Output Pin Direct Access Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " SOIP_SET/CLR ,Serial Input Output Pin Direct Access" "Low,High" bitfld.byte 0x0 1. " CCO ,Continuous Clock Output Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " SCES ,Serial Clock Edge Select" "Rising edge,Falling edge" else group.byte 0x0D++0x00 line.byte 0x0 "ESCR,Extended Status/Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " LBIE_SET/CLR ,LIN Sync Break Detection Interrupt Enable" "Disabled,Enabled" rbitfld.byte 0x0 6. " LBD ,Sync Break Detected Flag" "Not detected,Detected" bitfld.byte 0x0 4.--5. " LBL ,LIN Sync Break Length Selection (in bit times)" "17,18,19,20" textline " " bitfld.byte 0x0 3. " SOPE ,Serial Output Pin Direct Access Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " SOIP_SET/CLR ,Serial Input Output Pin Direct Access" "Low,High" bitfld.byte 0x0 1. " CCO ,Continuous Clock Output Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " SCES ,Serial Clock Edge Select" "Rising edge,Falling edge" endif group.byte 0x0E++0x00 line.byte 0x0 "ECCSR,Extended Communication Control Set Register" bitfld.byte 0x0 6. " LBRS ,LBR Set" "No effect,Set" bitfld.byte 0x0 2. " BIES ,BIE Set" "No effect,Set" group.byte 0x10++0x01 line.byte 0x00 "ECCCR,Extended Communication Control Clear Register" bitfld.byte 0x0 2. " BIEC ,BIE Clear" "No effect,Clear" line.byte 0x01 "ESCCR,Extended Status/Control Clear Register" bitfld.byte 0x1 6. " LBDC ,LBD Clear" "No effect,Clear" group.byte 0x12++0x00 line.byte 0x0 "ESIR,Extended Serial Interrupt Register" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " PEIE_SET/CLR ,Parity Error (in data received) Interrupt Enable bit" "Disabled,Enabled" setclrfld.byte 0x0 5. 0x2 5. 0x4 5. " OREIE_SET/CLR ,Overrun Error Interrupt Enable bit" "Disabled,Enabled" setclrfld.byte 0x0 4. 0x2 4. 0x4 4. " FREIE_SET/CLR ,Framing Error Interrupt Enable bit" "Disabled,Enabled" textline " " bitfld.byte 0x0 3. " TDRE ,Transmission Data Register Empty (Sticky Behaviour)" "Full,Empty" bitfld.byte 0x0 2. " RDRF ,Reception Data Register Full (Sticky Behaviour)" "Empty,Full" bitfld.byte 0x0 1. " RBI ,Reception Bus Idle (Sticky Behaviour)" "Reception,No reception" textline " " bitfld.byte 0x0 0. " AICD ,Auto Interrupt Clear Disable" "Enabled,Disabled" if (((per.b(ad:0x3F040000))&0xC0)==0xC0) group.byte 0x13++0x0 line.byte 0x0 "EIER,Extended Interrupt Enable Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFIE_SET/CLR ,Transmission FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " RXFIE_SET/CLR ,Reception FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 5. 0x2 5. 0x4 5. " SYNFEIE_SET/CLR ,Sync Field Error Interrupt Enable" "Disabled,Enabled" textline " " setclrfld.byte 0x0 4. 0x2 4. 0x4 4. " RXHDIE_SET/CLR ,Reception Header Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " TXHDIE_SET/CLR ,Transmission Header Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " PEFRDIE_SET/CLR ,Parity Error in Frame-ID Received Interrupt Enable" "Disabled,Enabled" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " BUSERRIE_SET/CLR ,Bus Error Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " LBSOIE_SET/CLR ,BLast Bit Shifted Out Interrupt Enable bit" "Disabled,Enabled" else group.byte 0x13++0x0 line.byte 0x0 "EIER,Extended Interrupt Enable Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFIE_SET/CLR ,Transmission FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " RXFIE_SET/CLR ,Reception FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " LBSOIE_SET/CLR ,BLast Bit Shifted Out Interrupt Enable bit" "Disabled,Enabled" endif wgroup.byte 0x16++0x0 line.byte 0x0 "ESICR,Extended Serial Interrupt Clear Register" bitfld.byte 0x0 3. " TDREC ,Transmission Data Register Empty Flag (TDRE) Clear" "No effect,Clear" bitfld.byte 0x0 2. " RDRFC ,Reception Data Register Full Flag (RDRF) Clear" "No effect,Clear" bitfld.byte 0x0 1. " RBIC ,Reception Bus Idle Flag (RBI) Clear" "No effect,Clear" group.byte 0x18++0x1 line.byte 0x0 "EFERL,Extended Feature Enable Register - L" bitfld.byte 0x0 6. " OSDE ,Oversampling Disable" "No,Yes" bitfld.byte 0x0 5. " DTSTART ,Detect Start bit" "Low level,Falling edge" bitfld.byte 0x0 4. " RSTRFM ,Reset Reception State Machine" "Enabled,Disabled" textline " " bitfld.byte 0x0 3. " LBEDGE ,LIN Break Edge Sensitive" "Level,Edge" bitfld.byte 0x0 2. " ABRE ,Auto Baud Rate Detection/Adjustment Enable" "Disabled,Enabled" bitfld.byte 0x0 1. " ENRXHR ,Automatic Header Detection Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " ENTXHR ,Automatic Header Transmission Enable" "Disabled,Enabled" line.byte 0x1 "EFERH,Extended Feature Enable Register - H" bitfld.byte 0x1 5. " INTLBEN ,Internal Loop Back Enable" "Disabled,Enabled" bitfld.byte 0x1 4. " BRGR ,Baud Rate Regiter Read" "Reload Counter Value,Reload Value of CPU/ABR" bitfld.byte 0x1 3. " FIDPE ,Enable for Parity Checking of Frame-ID" "Disabled,Enabled" textline " " bitfld.byte 0x1 2. " DBE ,Detection of Bus Error Enable" "Disabled,Enabled" bitfld.byte 0x1 1. " FIDE ,Frame-ID Register Enable" "Disabled,Enabled" bitfld.byte 0x1 0. " LBL2 ,MSB of LIN Break Length" "13-16,17-20" group.byte 0x1A++0x0 line.byte 0x0 "RFCR,Reception FIFO Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " RXFE_SET/CLR ,Reception FIFO Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " RXFCL ,Reception FIFO Clear" "Not reset,Reset" bitfld.byte 0x0 0.--4. " RXFLC ,Reception FIFO Level Configuration (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," group.byte 0x1B++0x0 line.byte 0x0 "TFCR,Transmission FIFO Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFE_SET/CLR ,Transmission FIFO Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " TXFCL ,Transmission FIFO Clear" "Not reset,Reset" bitfld.byte 0x0 0.--4. " TXFLC ,Transmission FIFO Level Configuration (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," wgroup.byte 0x1E++0x1 line.byte 0x0 "RFCCR,Reception FIFO Control Clear Register" bitfld.byte 0x0 6. " RXFCLC ,RXFCL Clear" "No effect,Clear" line.byte 0x1 "TFCCR,Transmission FIFO Control Clear Register" bitfld.byte 0x1 6. " TXFCLC ,TXFCL Clear" "No effect,Clear" group.byte 0x20++0x1 line.byte 0x0 "RFSR,Reception FIFO Status Register" bitfld.byte 0x0 0.--4. " RXFVD ,Reception FIFO Valid Data (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," line.byte 0x1 "TFSR,Transmission FIFO Status Register" bitfld.byte 0x1 0.--4. " TXFVD ,Transmission FIFO Valid Data (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," group.byte 0x22++0x0 "Checksum Register" line.byte 0x0 "CSCR,Checksum Status and Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " CRCERRIE_set/clr ,Checksum Error Interrupt Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " CCRCERR ,CRC Error Flag" "No error,Error" bitfld.byte 0x0 5. " CRCTYPE ,Checksum Type" "Classic,Enhanced" textline " " bitfld.byte 0x0 4. " CRCCHECK ,Checksum Verification Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " CRCGEN ,Checksum Generation Enable" "Disabled,Enabled" bitfld.byte 0x0 0.--2. " DL ,Data Length in LIN Frame (in bytes)" "1,2,3,4,5,6,7,8" wgroup.byte 0x26++0x0 line.byte 0x0 "CSCCR,Checksum Status and Control Clear Register" bitfld.byte 0x0 6. " CRCERRC ,CRCERR Clear" "No effect,Clear" rgroup.byte 0x23++0x0 "Status Register" line.byte 0x0 "ESR,Extended Status Register" bitfld.byte 0x0 6. " AD ,AD Status of Received Frame" "Usual data,Address" bitfld.byte 0x0 5. " TXHRI ,Transmission of Header" "Not completed,Completed" bitfld.byte 0x0 4. " RXHRI ,Reception of Header" "Not completed,Completed" textline " " bitfld.byte 0x0 3. " LBSOF ,Last Bit Shift Out Flag" "Not shifted out,Shifted out" bitfld.byte 0x0 2. " BUSERR ,Bus Error Flag" "No error,Error" bitfld.byte 0x0 1. " PEFRD ,Parity Error in Frame-ID" "No error,Error" textline " " bitfld.byte 0x0 0. " SYNFE ,Sync Field Error Flag" "No error,Error" wgroup.byte 0x27++0x0 line.byte 0x0 "ESCLR,Extended Status Clear Register" bitfld.byte 0x00 5. " TXHRIC ,TXHRI Clear" "No effect,Clear" bitfld.byte 0x00 4. " RXHRIC ,RXHRI Clear" "No effect,Clear" bitfld.byte 0x00 3. " LBSOFC ,LBSOF Clear" "No effect,Clear" textline " " bitfld.byte 0x00 2. " BUSERRC ,BUSERR Clear" "No effect,Clear" bitfld.byte 0x00 1. " PEFRDC ,PEFRD Clear" "No effect,Clear" bitfld.byte 0x00 0. " SYNFEC ,SYNFEC Clear" "No effect,Clear" wgroup.byte 0x28++0x2 "Baud Rate Registers" line.byte 0x0 "BGRLL,Baud Rate Generation Reload Register - L (bits[7:0])" line.byte 0x1 "BGRLM,Baud Rate Generation Reload Register - M (bits[15:8])" line.byte 0x2 "BGRLH,Baud Rate Generation Reload Register - H (bits[18:16])" bitfld.byte 0x2 0.--2. " Value[18:16] ,Baud Rate Generation Reload Register - H bits 16..18" "0,1,2,3,4,5,6,7" rgroup.byte 0x2C++0x2 line.byte 0x0 "BGRL,Baud Rate Generation Register - L (bits[0:7])" line.byte 0x1 "BGRM,Baud Rate Generation Register - M (bits[8:15])" line.byte 0x2 "BGRH,Baud Rate Generation Register - H (bits[16:18])" bitfld.byte 0x2 0.--2. " Value[18:16] ,Baud Rate Generation Register - H bits 16..18" "0,1,2,3,4,5,6,7" group.byte 0x30++0x00 "DMA Configuration Registers" line.byte 0x0 "STXDR,Serial Transmit DMA Configuration Register" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " TXDISDOERR_SET/CLR ,TX-DMA Request Mask/Disable" "No,Yes" setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " TXDRQEN_SET/CLR ,TX-DMA Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXDDEN_SET/CLR ,TX-DMA Demand Transfer Enable" "Disabled,Enabled" group.byte 0x31++0x00 line.byte 0x0 "SRXDR,Serial Receive DMA Configuration Register" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " RXDISDOERR_SET/CLR ,RX-DMA Request Mask/Disable" "No,Yes" setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXDRQEN_SET/CLR ,RX-DMA Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " RXDDEN_SET/CLR ,RX-DMA Demand Transfer Enable" "Disabled,Enabled" group.byte 0x36++0x02 "Sync Field Timeout Registers" line.byte 0x00 "SFTRL,Sync Field Timeout Register - L (bits[7:0])" line.byte 0x01 "SFTRM,Sync Field Timeout Register - M (bits[15:8])" line.byte 0x02 "SFTRH,Sync Field Timeout Register - H (bits[18:16])" bitfld.byte 0x02 0.--2. " VALUE[18:16] ,Sync Field Timeout Register - H bits 16..18" "0,1,2,3,4,5,6,7" group.byte 0x3A++0x0 "Frame-ID and Debug Register" line.byte 0x0 "FIDR,Frame-ID Register" sif (cpu()!="MB86R11F") group.byte 0x3C++0x0 line.byte 0x0 "DEBUG,Debug Register" bitfld.byte 0x0 0. " DBGEN ,Debug Enable" "Disabled,Enabled" endif width 12. tree.end tree "USART_5" base ad:0x3F050000 width 14. group.byte 0x00++0x00 "Mode and Control Registers" line.byte 0x00 "SMR,Serial Mode Register" bitfld.byte 0x0 6.--7. " MD ,Operation Mode Select" "Asynchronous normal,Asynchronous multiprocessor,Synchronous,Asynchronous LIN" bitfld.byte 0x0 5. " OTO ,One-to-One External Clock Selection" "Reload counter,External clock" bitfld.byte 0x0 4. " EXT ,External Clock Selection" "Reload counter,External clock" textline " " bitfld.byte 0x0 3. " REST ,Restart of Transmission Reload Counter" "No reset,Restart" bitfld.byte 0x0 2. " UPCL ,LIN-USART Programmable Clear" "No reset,Reset" if ((((per.b(ad:0x3F050000))&0xC0)==0x00)||(((per.b(ad:0x3F050000))&0xC0)==0x80)&&(((per.b(ad:0x3F050000+0x0C))&0x08)==0x08)) group.byte 0x01++0x00 line.byte 0x0 "SCR,Serial Control Register" bitfld.byte 0x0 7. " PEN ,Parity Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " P ,Parity Selection" "Even,Odd" bitfld.byte 0x0 5. " SBL ,Stop Bit Length Selection" "1,2" textline " " bitfld.byte 0x0 4. " CL ,Character (Data frame) Length (in bits)" "7,8" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " AD_SET/CLR ,Address or Data Selection" "Data,Address" bitfld.byte 0x0 2. " CRE ,Clear Reception Error Flags" "No effect,Clear" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXE_SET/CLR ,Reception Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXE_SET/CLR ,Transmission Enable" "Disabled,Enabled" else group.byte 0x01++0x00 line.byte 0x0 "SCR,Serial Control Register" bitfld.byte 0x0 6. " P ,Parity Selection" "Even,Odd" bitfld.byte 0x0 5. " SBL ,Stop Bit Length Selection" "1,2" textline " " bitfld.byte 0x0 4. " CL ,Character (Data frame) Length (in bits)" "7,8" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " AD_SET/CLR ,Address or Data Selection" "Data,Address" bitfld.byte 0x0 2. " CRE ,Clear Reception Error Flags" "No effect,Clear" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXE_SET/CLR ,Reception Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXE_SET/CLR ,Transmission Enable" "Disabled,Enabled" endif wgroup.byte 0x2++0x1 line.byte 0x0 "SMSR,Serial Mode Set Register" bitfld.byte 0x0 3. " RESTS ,REST Set" "No effect,Set" bitfld.byte 0x0 2. " UPCLS ,UPCL Set" "No effect,Set" line.byte 0x1 "SCSR,Serial Control Set Register" bitfld.byte 0x1 2. " CRES ,CRE Set" "No effect,Set" wgroup.byte 0x06++0x0 "Transmission Data Register" line.byte 0x0 "TDR,Transmission Data Register" hexmask.byte 0x0 0.--7. 1. " D[7:0] ,Transmission data" group.byte 0x07++0x0 "Status Register" line.byte 0x0 "SSR,Serial Status Register" rbitfld.byte 0x0 7. " PE ,Parity Error Flag" "No error,Error" rbitfld.byte 0x0 6. " ORE ,Overrun Error Flag" "No error,Error" rbitfld.byte 0x0 5. " FRE ,Framing Error Flag" "No error,Error" textline " " rbitfld.byte 0x0 4. " RDRF ,Receive Data Register Full Flag" "Empty,Full" bitfld.byte 0x0 3. " TDRE ,Transmission Data Register Empty" "Full,Empty" bitfld.byte 0x0 2. " BDS ,Transfer Direction Selection" "LSB,MSB" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RIE_SET/CLR ,Receive Interrupt Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TIE_SET/CLR ,Transmission Interrupt Request Enable" "Disabled,Enabled" hgroup.byte 0x08++0x00 "Reception Data Register" hide.byte 0x0 "RDR,Reception Data Register" in if ((((per.b(ad:0x3F050000+0x0C))&0x20)==0x20)&&(((per.b(ad:0x3F050000))&0xC0)==0x80)) group.byte 0x0C++0x00 "Extended Registers" line.byte 0x0 "ECCR,Extended Communication Control Register" bitfld.byte 0x0 7. " INV ,Invert Serial Data" "Not inverted,Inverted" bitfld.byte 0x0 6. " LBR ,Generate LIN Sync Break" "Ignored,Generated" bitfld.byte 0x0 5. " MS ,Master Slave Mode select" "Master mode,Slave mode" textline " " bitfld.byte 0x0 4. " SCDE ,Serial Clock Delay Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " SSM ,Start_Stop Bit Mode Enable" "Disabled,Enabled" else group.byte 0x0C++0x00 "Extended Registers" line.byte 0x0 "ECCR,Extended Communication Control Register" bitfld.byte 0x0 7. " INV ,Invert Serial Data" "Not inverted,Inverted" bitfld.byte 0x0 6. " LBR ,Generate LIN Sync Break" "Ignored,Generated" bitfld.byte 0x0 5. " MS ,Master Slave Mode select" "Master mode,Slave mode" textline " " bitfld.byte 0x0 4. " SCDE ,Serial Clock Delay Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " SSM ,Start_Stop Bit Mode Enable" "Disabled,Enabled" bitfld.byte 0x0 2. " BIE ,Bus Idle Interrupt Enable" "Disabled,Enabled" textline " " rbitfld.byte 0x0 1. " RBI ,Reception Bus Idle Flag" "Reception,No reception" rbitfld.byte 0x0 0. " TBI ,Transmission Bus Idle Flag" "Transmission,No transmission" endif if (((per.b(ad:0x3F050000+0x19))&0x1)==0x0) group.byte 0x0D++0x00 line.byte 0x0 "ESCR,Extended Status/Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " LBIE_SET/CLR ,LIN Sync Break Detection Interrupt Enable" "Disabled,Enabled" rbitfld.byte 0x0 6. " LBD ,Sync Break Detected Flag" "Not detected,Detected" bitfld.byte 0x0 4.--5. " LBL ,LIN Sync Break Length Selection (in bit times)" "13,14,15,16" textline " " bitfld.byte 0x0 3. " SOPE ,Serial Output Pin Direct Access Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " SOIP_SET/CLR ,Serial Input Output Pin Direct Access" "Low,High" bitfld.byte 0x0 1. " CCO ,Continuous Clock Output Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " SCES ,Serial Clock Edge Select" "Rising edge,Falling edge" else group.byte 0x0D++0x00 line.byte 0x0 "ESCR,Extended Status/Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " LBIE_SET/CLR ,LIN Sync Break Detection Interrupt Enable" "Disabled,Enabled" rbitfld.byte 0x0 6. " LBD ,Sync Break Detected Flag" "Not detected,Detected" bitfld.byte 0x0 4.--5. " LBL ,LIN Sync Break Length Selection (in bit times)" "17,18,19,20" textline " " bitfld.byte 0x0 3. " SOPE ,Serial Output Pin Direct Access Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " SOIP_SET/CLR ,Serial Input Output Pin Direct Access" "Low,High" bitfld.byte 0x0 1. " CCO ,Continuous Clock Output Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " SCES ,Serial Clock Edge Select" "Rising edge,Falling edge" endif group.byte 0x0E++0x00 line.byte 0x0 "ECCSR,Extended Communication Control Set Register" bitfld.byte 0x0 6. " LBRS ,LBR Set" "No effect,Set" bitfld.byte 0x0 2. " BIES ,BIE Set" "No effect,Set" group.byte 0x10++0x01 line.byte 0x00 "ECCCR,Extended Communication Control Clear Register" bitfld.byte 0x0 2. " BIEC ,BIE Clear" "No effect,Clear" line.byte 0x01 "ESCCR,Extended Status/Control Clear Register" bitfld.byte 0x1 6. " LBDC ,LBD Clear" "No effect,Clear" group.byte 0x12++0x00 line.byte 0x0 "ESIR,Extended Serial Interrupt Register" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " PEIE_SET/CLR ,Parity Error (in data received) Interrupt Enable bit" "Disabled,Enabled" setclrfld.byte 0x0 5. 0x2 5. 0x4 5. " OREIE_SET/CLR ,Overrun Error Interrupt Enable bit" "Disabled,Enabled" setclrfld.byte 0x0 4. 0x2 4. 0x4 4. " FREIE_SET/CLR ,Framing Error Interrupt Enable bit" "Disabled,Enabled" textline " " bitfld.byte 0x0 3. " TDRE ,Transmission Data Register Empty (Sticky Behaviour)" "Full,Empty" bitfld.byte 0x0 2. " RDRF ,Reception Data Register Full (Sticky Behaviour)" "Empty,Full" bitfld.byte 0x0 1. " RBI ,Reception Bus Idle (Sticky Behaviour)" "Reception,No reception" textline " " bitfld.byte 0x0 0. " AICD ,Auto Interrupt Clear Disable" "Enabled,Disabled" if (((per.b(ad:0x3F050000))&0xC0)==0xC0) group.byte 0x13++0x0 line.byte 0x0 "EIER,Extended Interrupt Enable Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFIE_SET/CLR ,Transmission FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " RXFIE_SET/CLR ,Reception FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 5. 0x2 5. 0x4 5. " SYNFEIE_SET/CLR ,Sync Field Error Interrupt Enable" "Disabled,Enabled" textline " " setclrfld.byte 0x0 4. 0x2 4. 0x4 4. " RXHDIE_SET/CLR ,Reception Header Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 3. 0x2 3. 0x4 3. " TXHDIE_SET/CLR ,Transmission Header Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " PEFRDIE_SET/CLR ,Parity Error in Frame-ID Received Interrupt Enable" "Disabled,Enabled" textline " " setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " BUSERRIE_SET/CLR ,Bus Error Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " LBSOIE_SET/CLR ,BLast Bit Shifted Out Interrupt Enable bit" "Disabled,Enabled" else group.byte 0x13++0x0 line.byte 0x0 "EIER,Extended Interrupt Enable Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFIE_SET/CLR ,Transmission FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 6. 0x2 6. 0x4 6. " RXFIE_SET/CLR ,Reception FIFO Interrupt Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " LBSOIE_SET/CLR ,BLast Bit Shifted Out Interrupt Enable bit" "Disabled,Enabled" endif wgroup.byte 0x16++0x0 line.byte 0x0 "ESICR,Extended Serial Interrupt Clear Register" bitfld.byte 0x0 3. " TDREC ,Transmission Data Register Empty Flag (TDRE) Clear" "No effect,Clear" bitfld.byte 0x0 2. " RDRFC ,Reception Data Register Full Flag (RDRF) Clear" "No effect,Clear" bitfld.byte 0x0 1. " RBIC ,Reception Bus Idle Flag (RBI) Clear" "No effect,Clear" group.byte 0x18++0x1 line.byte 0x0 "EFERL,Extended Feature Enable Register - L" bitfld.byte 0x0 6. " OSDE ,Oversampling Disable" "No,Yes" bitfld.byte 0x0 5. " DTSTART ,Detect Start bit" "Low level,Falling edge" bitfld.byte 0x0 4. " RSTRFM ,Reset Reception State Machine" "Enabled,Disabled" textline " " bitfld.byte 0x0 3. " LBEDGE ,LIN Break Edge Sensitive" "Level,Edge" bitfld.byte 0x0 2. " ABRE ,Auto Baud Rate Detection/Adjustment Enable" "Disabled,Enabled" bitfld.byte 0x0 1. " ENRXHR ,Automatic Header Detection Enable" "Disabled,Enabled" textline " " bitfld.byte 0x0 0. " ENTXHR ,Automatic Header Transmission Enable" "Disabled,Enabled" line.byte 0x1 "EFERH,Extended Feature Enable Register - H" bitfld.byte 0x1 5. " INTLBEN ,Internal Loop Back Enable" "Disabled,Enabled" bitfld.byte 0x1 4. " BRGR ,Baud Rate Regiter Read" "Reload Counter Value,Reload Value of CPU/ABR" bitfld.byte 0x1 3. " FIDPE ,Enable for Parity Checking of Frame-ID" "Disabled,Enabled" textline " " bitfld.byte 0x1 2. " DBE ,Detection of Bus Error Enable" "Disabled,Enabled" bitfld.byte 0x1 1. " FIDE ,Frame-ID Register Enable" "Disabled,Enabled" bitfld.byte 0x1 0. " LBL2 ,MSB of LIN Break Length" "13-16,17-20" group.byte 0x1A++0x0 line.byte 0x0 "RFCR,Reception FIFO Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " RXFE_SET/CLR ,Reception FIFO Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " RXFCL ,Reception FIFO Clear" "Not reset,Reset" bitfld.byte 0x0 0.--4. " RXFLC ,Reception FIFO Level Configuration (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," group.byte 0x1B++0x0 line.byte 0x0 "TFCR,Transmission FIFO Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " TXFE_SET/CLR ,Transmission FIFO Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " TXFCL ,Transmission FIFO Clear" "Not reset,Reset" bitfld.byte 0x0 0.--4. " TXFLC ,Transmission FIFO Level Configuration (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," wgroup.byte 0x1E++0x1 line.byte 0x0 "RFCCR,Reception FIFO Control Clear Register" bitfld.byte 0x0 6. " RXFCLC ,RXFCL Clear" "No effect,Clear" line.byte 0x1 "TFCCR,Transmission FIFO Control Clear Register" bitfld.byte 0x1 6. " TXFCLC ,TXFCL Clear" "No effect,Clear" group.byte 0x20++0x1 line.byte 0x0 "RFSR,Reception FIFO Status Register" bitfld.byte 0x0 0.--4. " RXFVD ,Reception FIFO Valid Data (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," line.byte 0x1 "TFSR,Transmission FIFO Status Register" bitfld.byte 0x1 0.--4. " TXFVD ,Transmission FIFO Valid Data (in data bytes)" "Empty,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,,,,,,,,,,,,,,," group.byte 0x22++0x0 "Checksum Register" line.byte 0x0 "CSCR,Checksum Status and Control Register" setclrfld.byte 0x0 7. 0x2 7. 0x4 7. " CRCERRIE_set/clr ,Checksum Error Interrupt Enable" "Disabled,Enabled" bitfld.byte 0x0 6. " CCRCERR ,CRC Error Flag" "No error,Error" bitfld.byte 0x0 5. " CRCTYPE ,Checksum Type" "Classic,Enhanced" textline " " bitfld.byte 0x0 4. " CRCCHECK ,Checksum Verification Enable" "Disabled,Enabled" bitfld.byte 0x0 3. " CRCGEN ,Checksum Generation Enable" "Disabled,Enabled" bitfld.byte 0x0 0.--2. " DL ,Data Length in LIN Frame (in bytes)" "1,2,3,4,5,6,7,8" wgroup.byte 0x26++0x0 line.byte 0x0 "CSCCR,Checksum Status and Control Clear Register" bitfld.byte 0x0 6. " CRCERRC ,CRCERR Clear" "No effect,Clear" rgroup.byte 0x23++0x0 "Status Register" line.byte 0x0 "ESR,Extended Status Register" bitfld.byte 0x0 6. " AD ,AD Status of Received Frame" "Usual data,Address" bitfld.byte 0x0 5. " TXHRI ,Transmission of Header" "Not completed,Completed" bitfld.byte 0x0 4. " RXHRI ,Reception of Header" "Not completed,Completed" textline " " bitfld.byte 0x0 3. " LBSOF ,Last Bit Shift Out Flag" "Not shifted out,Shifted out" bitfld.byte 0x0 2. " BUSERR ,Bus Error Flag" "No error,Error" bitfld.byte 0x0 1. " PEFRD ,Parity Error in Frame-ID" "No error,Error" textline " " bitfld.byte 0x0 0. " SYNFE ,Sync Field Error Flag" "No error,Error" wgroup.byte 0x27++0x0 line.byte 0x0 "ESCLR,Extended Status Clear Register" bitfld.byte 0x00 5. " TXHRIC ,TXHRI Clear" "No effect,Clear" bitfld.byte 0x00 4. " RXHRIC ,RXHRI Clear" "No effect,Clear" bitfld.byte 0x00 3. " LBSOFC ,LBSOF Clear" "No effect,Clear" textline " " bitfld.byte 0x00 2. " BUSERRC ,BUSERR Clear" "No effect,Clear" bitfld.byte 0x00 1. " PEFRDC ,PEFRD Clear" "No effect,Clear" bitfld.byte 0x00 0. " SYNFEC ,SYNFEC Clear" "No effect,Clear" wgroup.byte 0x28++0x2 "Baud Rate Registers" line.byte 0x0 "BGRLL,Baud Rate Generation Reload Register - L (bits[7:0])" line.byte 0x1 "BGRLM,Baud Rate Generation Reload Register - M (bits[15:8])" line.byte 0x2 "BGRLH,Baud Rate Generation Reload Register - H (bits[18:16])" bitfld.byte 0x2 0.--2. " Value[18:16] ,Baud Rate Generation Reload Register - H bits 16..18" "0,1,2,3,4,5,6,7" rgroup.byte 0x2C++0x2 line.byte 0x0 "BGRL,Baud Rate Generation Register - L (bits[0:7])" line.byte 0x1 "BGRM,Baud Rate Generation Register - M (bits[8:15])" line.byte 0x2 "BGRH,Baud Rate Generation Register - H (bits[16:18])" bitfld.byte 0x2 0.--2. " Value[18:16] ,Baud Rate Generation Register - H bits 16..18" "0,1,2,3,4,5,6,7" group.byte 0x30++0x00 "DMA Configuration Registers" line.byte 0x0 "STXDR,Serial Transmit DMA Configuration Register" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " TXDISDOERR_SET/CLR ,TX-DMA Request Mask/Disable" "No,Yes" setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " TXDRQEN_SET/CLR ,TX-DMA Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " TXDDEN_SET/CLR ,TX-DMA Demand Transfer Enable" "Disabled,Enabled" group.byte 0x31++0x00 line.byte 0x0 "SRXDR,Serial Receive DMA Configuration Register" setclrfld.byte 0x0 2. 0x2 2. 0x4 2. " RXDISDOERR_SET/CLR ,RX-DMA Request Mask/Disable" "No,Yes" setclrfld.byte 0x0 1. 0x2 1. 0x4 1. " RXDRQEN_SET/CLR ,RX-DMA Request Enable" "Disabled,Enabled" setclrfld.byte 0x0 0. 0x2 0. 0x4 0. " RXDDEN_SET/CLR ,RX-DMA Demand Transfer Enable" "Disabled,Enabled" group.byte 0x36++0x02 "Sync Field Timeout Registers" line.byte 0x00 "SFTRL,Sync Field Timeout Register - L (bits[7:0])" line.byte 0x01 "SFTRM,Sync Field Timeout Register - M (bits[15:8])" line.byte 0x02 "SFTRH,Sync Field Timeout Register - H (bits[18:16])" bitfld.byte 0x02 0.--2. " VALUE[18:16] ,Sync Field Timeout Register - H bits 16..18" "0,1,2,3,4,5,6,7" group.byte 0x3A++0x0 "Frame-ID and Debug Register" line.byte 0x0 "FIDR,Frame-ID Register" sif (cpu()!="MB86R11F") group.byte 0x3C++0x0 line.byte 0x0 "DEBUG,Debug Register" bitfld.byte 0x0 0. " DBGEN ,Debug Enable" "Disabled,Enabled" endif width 12. tree.end tree.end sif (cpu()=="MB86R12") tree "I2C BUS interface" tree "I2C ch0" base ad:0x3D200000 width 10. rgroup.byte 0x00++0x00 line.byte 0x00 "I2C0BSR,Bus status register" bitfld.byte 0x00 7. " BB ,Bus busy" "Stop,Start" bitfld.byte 0x00 6. " RSC ,Repeated Start Condition" "Not detected,Detected" bitfld.byte 0x00 5. " AL ,Arbitration Lost" "Not detected,Detected" bitfld.byte 0x00 4. " LRB ,LAST Received Bit" "ACK ,NACK" textline " " bitfld.byte 0x00 3. " TRX ,Transfer/Receive" "Reception state,Transmission state" bitfld.byte 0x00 2. " AAS ,Address As Slave" "Not performed,Performed" bitfld.byte 0x00 1. " GCA ,General Call Address" "Not received,Received" bitfld.byte 0x00 0. " FBT ,First Byte Transfer" "Not first byte,First byte" group.byte 0x01++0x00 line.byte 0x00 "I2C0BCR,Bus control register" bitfld.byte 0x00 7. " BER ,Bus Error" "Not detected,Detected" bitfld.byte 0x00 6. " BEIE ,Bus Error Interrupt Enable" "Prohibited,Permitted" eventfld.byte 0x00 5. " SCC ,Start Condition Continue" "Not available,Start" bitfld.byte 0x00 4. " MSS ,Master Slave Select" "Slave mode,Master mode" textline " " bitfld.byte 0x00 3. " ACK ,ACKnowledge" "Not Occurred,Occurred" bitfld.byte 0x00 2. " GCAA ,General Call Address Acknowledge" "Not Occurred,Occurred" bitfld.byte 0x00 1. " INTE ,INTerrupt Enable " "Disabled,Enabled" bitfld.byte 0x00 0. " INT ,INTerrupt" "Not interrupt,Interrupt" if (((per.b(ad:0x3D200000+0x02))&0x40)==0x40) rgroup.byte 0x02++0x00 line.byte 0x00 "I2C0CCR,Clock control register" bitfld.byte 0x00 6. " HSM ,High Speed Mode" "Standard,High-speed mode" bitfld.byte 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.byte 0x00 0.--4. " CS ,Clock Period Select" ",,,,,,,,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32" else rgroup.byte 0x02++0x00 line.byte 0x00 "I2C0CCR,Clock control register" bitfld.byte 0x00 6. " HSM ,High Speed Mode" "Standard,High-speed mode" bitfld.byte 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.byte 0x00 0.--4. " CS ,Clock Period Select" "65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96" endif group.byte 0x03++0x01 line.byte 0x00 "I2C0ADR,Address register" hexmask.byte 0x00 0.--6. 1. " AS ,This is slave address storage bit" line.byte 0x01 "I2C0DAR,Data register" hexmask.byte 0x01 0.--7. 1. " DS ,This is serial data storage bit" group.byte 0x5++0x02 line.byte 0x00 "I2C0CSR,Expand Clock Period Select Register" bitfld.byte 0x00 0.--5. " CS ,Clock Period Select 10-5" "No upper limit,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.byte 0x01 "I2C0FSR,I2C Bus Clock Frequency Register" bitfld.byte 0x01 0.--3. " FS ,Bus Clock Frequency Select" ",14-20,20-40,40-60,60-80,80-100,100-120,120-140,140-160,160-180,180-200,200-220,,,," line.byte 0x02 "I2C0BC2R,Two bus control registers" bitfld.byte 0x02 5. " SDAS ,SDA status" "Low,High" bitfld.byte 0x02 4. " SCLS ,SCL status" "Low,High" bitfld.byte 0x02 1. " SDAL ,SDA low drive" "Normal operation,Forcibly become 'L'" bitfld.byte 0x02 0. " SCLL ,SCL Low drive" "Normal operation,Forcibly become 'L'" width 0xb tree.end tree "I2C ch1" base ad:0x3D210000 width 10. rgroup.byte 0x00++0x00 line.byte 0x00 "I2C1BSR,Bus status register" bitfld.byte 0x00 7. " BB ,Bus busy" "Stop,Start" bitfld.byte 0x00 6. " RSC ,Repeated Start Condition" "Not detected,Detected" bitfld.byte 0x00 5. " AL ,Arbitration Lost" "Not detected,Detected" bitfld.byte 0x00 4. " LRB ,LAST Received Bit" "ACK ,NACK" textline " " bitfld.byte 0x00 3. " TRX ,Transfer/Receive" "Reception state,Transmission state" bitfld.byte 0x00 2. " AAS ,Address As Slave" "Not performed,Performed" bitfld.byte 0x00 1. " GCA ,General Call Address" "Not received,Received" bitfld.byte 0x00 0. " FBT ,First Byte Transfer" "Not first byte,First byte" group.byte 0x01++0x00 line.byte 0x00 "I2C1BCR,Bus control register" bitfld.byte 0x00 7. " BER ,Bus Error" "Not detected,Detected" bitfld.byte 0x00 6. " BEIE ,Bus Error Interrupt Enable" "Prohibited,Permitted" eventfld.byte 0x00 5. " SCC ,Start Condition Continue" "Not available,Start" bitfld.byte 0x00 4. " MSS ,Master Slave Select" "Slave mode,Master mode" textline " " bitfld.byte 0x00 3. " ACK ,ACKnowledge" "Not Occurred,Occurred" bitfld.byte 0x00 2. " GCAA ,General Call Address Acknowledge" "Not Occurred,Occurred" bitfld.byte 0x00 1. " INTE ,INTerrupt Enable " "Disabled,Enabled" bitfld.byte 0x00 0. " INT ,INTerrupt" "Not interrupt,Interrupt" if (((per.b(ad:0x3D210000+0x02))&0x40)==0x40) rgroup.byte 0x02++0x00 line.byte 0x00 "I2C1CCR,Clock control register" bitfld.byte 0x00 6. " HSM ,High Speed Mode" "Standard,High-speed mode" bitfld.byte 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.byte 0x00 0.--4. " CS ,Clock Period Select" ",,,,,,,,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32" else rgroup.byte 0x02++0x00 line.byte 0x00 "I2C1CCR,Clock control register" bitfld.byte 0x00 6. " HSM ,High Speed Mode" "Standard,High-speed mode" bitfld.byte 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.byte 0x00 0.--4. " CS ,Clock Period Select" "65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96" endif group.byte 0x03++0x01 line.byte 0x00 "I2C1ADR,Address register" hexmask.byte 0x00 0.--6. 1. " AS ,This is slave address storage bit" line.byte 0x01 "I2C1DAR,Data register" hexmask.byte 0x01 0.--7. 1. " DS ,This is serial data storage bit" group.byte 0x5++0x02 line.byte 0x00 "I2C1CSR,Expand Clock Period Select Register" bitfld.byte 0x00 0.--5. " CS ,Clock Period Select 10-5" "No upper limit,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.byte 0x01 "I2C1FSR,I2C Bus Clock Frequency Register" bitfld.byte 0x01 0.--3. " FS ,Bus Clock Frequency Select" ",14-20,20-40,40-60,60-80,80-100,100-120,120-140,140-160,160-180,180-200,200-220,,,," line.byte 0x02 "I2C1BC2R,Two bus control registers" bitfld.byte 0x02 5. " SDAS ,SDA status" "Low,High" bitfld.byte 0x02 4. " SCLS ,SCL status" "Low,High" bitfld.byte 0x02 1. " SDAL ,SDA low drive" "Normal operation,Forcibly become 'L'" bitfld.byte 0x02 0. " SCLL ,SCL Low drive" "Normal operation,Forcibly become 'L'" width 0xb tree.end tree "I2C ch2" base ad:0x3D220000 width 10. rgroup.byte 0x00++0x00 line.byte 0x00 "I2C2BSR,Bus status register" bitfld.byte 0x00 7. " BB ,Bus busy" "Stop,Start" bitfld.byte 0x00 6. " RSC ,Repeated Start Condition" "Not detected,Detected" bitfld.byte 0x00 5. " AL ,Arbitration Lost" "Not detected,Detected" bitfld.byte 0x00 4. " LRB ,LAST Received Bit" "ACK ,NACK" textline " " bitfld.byte 0x00 3. " TRX ,Transfer/Receive" "Reception state,Transmission state" bitfld.byte 0x00 2. " AAS ,Address As Slave" "Not performed,Performed" bitfld.byte 0x00 1. " GCA ,General Call Address" "Not received,Received" bitfld.byte 0x00 0. " FBT ,First Byte Transfer" "Not first byte,First byte" group.byte 0x01++0x00 line.byte 0x00 "I2C2BCR,Bus control register" bitfld.byte 0x00 7. " BER ,Bus Error" "Not detected,Detected" bitfld.byte 0x00 6. " BEIE ,Bus Error Interrupt Enable" "Prohibited,Permitted" eventfld.byte 0x00 5. " SCC ,Start Condition Continue" "Not available,Start" bitfld.byte 0x00 4. " MSS ,Master Slave Select" "Slave mode,Master mode" textline " " bitfld.byte 0x00 3. " ACK ,ACKnowledge" "Not Occurred,Occurred" bitfld.byte 0x00 2. " GCAA ,General Call Address Acknowledge" "Not Occurred,Occurred" bitfld.byte 0x00 1. " INTE ,INTerrupt Enable " "Disabled,Enabled" bitfld.byte 0x00 0. " INT ,INTerrupt" "Not interrupt,Interrupt" if (((per.b(ad:0x3D220000+0x02))&0x40)==0x40) rgroup.byte 0x02++0x00 line.byte 0x00 "I2C2CCR,Clock control register" bitfld.byte 0x00 6. " HSM ,High Speed Mode" "Standard,High-speed mode" bitfld.byte 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.byte 0x00 0.--4. " CS ,Clock Period Select" ",,,,,,,,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32" else rgroup.byte 0x02++0x00 line.byte 0x00 "I2C2CCR,Clock control register" bitfld.byte 0x00 6. " HSM ,High Speed Mode" "Standard,High-speed mode" bitfld.byte 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.byte 0x00 0.--4. " CS ,Clock Period Select" "65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96" endif group.byte 0x03++0x01 line.byte 0x00 "I2C2ADR,Address register" hexmask.byte 0x00 0.--6. 1. " AS ,This is slave address storage bit" line.byte 0x01 "I2C2DAR,Data register" hexmask.byte 0x01 0.--7. 1. " DS ,This is serial data storage bit" group.byte 0x5++0x02 line.byte 0x00 "I2C2CSR,Expand Clock Period Select Register" bitfld.byte 0x00 0.--5. " CS ,Clock Period Select 10-5" "No upper limit,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.byte 0x01 "I2C2FSR,I2C Bus Clock Frequency Register" bitfld.byte 0x01 0.--3. " FS ,Bus Clock Frequency Select" ",14-20,20-40,40-60,60-80,80-100,100-120,120-140,140-160,160-180,180-200,200-220,,,," line.byte 0x02 "I2C2BC2R,Two bus control registers" bitfld.byte 0x02 5. " SDAS ,SDA status" "Low,High" bitfld.byte 0x02 4. " SCLS ,SCL status" "Low,High" bitfld.byte 0x02 1. " SDAL ,SDA low drive" "Normal operation,Forcibly become 'L'" bitfld.byte 0x02 0. " SCLL ,SCL Low drive" "Normal operation,Forcibly become 'L'" width 0xb tree.end tree "I2C ch3" base ad:0x3D230000 width 10. rgroup.byte 0x00++0x00 line.byte 0x00 "I2C3BSR,Bus status register" bitfld.byte 0x00 7. " BB ,Bus busy" "Stop,Start" bitfld.byte 0x00 6. " RSC ,Repeated Start Condition" "Not detected,Detected" bitfld.byte 0x00 5. " AL ,Arbitration Lost" "Not detected,Detected" bitfld.byte 0x00 4. " LRB ,LAST Received Bit" "ACK ,NACK" textline " " bitfld.byte 0x00 3. " TRX ,Transfer/Receive" "Reception state,Transmission state" bitfld.byte 0x00 2. " AAS ,Address As Slave" "Not performed,Performed" bitfld.byte 0x00 1. " GCA ,General Call Address" "Not received,Received" bitfld.byte 0x00 0. " FBT ,First Byte Transfer" "Not first byte,First byte" group.byte 0x01++0x00 line.byte 0x00 "I2C3BCR,Bus control register" bitfld.byte 0x00 7. " BER ,Bus Error" "Not detected,Detected" bitfld.byte 0x00 6. " BEIE ,Bus Error Interrupt Enable" "Prohibited,Permitted" eventfld.byte 0x00 5. " SCC ,Start Condition Continue" "Not available,Start" bitfld.byte 0x00 4. " MSS ,Master Slave Select" "Slave mode,Master mode" textline " " bitfld.byte 0x00 3. " ACK ,ACKnowledge" "Not Occurred,Occurred" bitfld.byte 0x00 2. " GCAA ,General Call Address Acknowledge" "Not Occurred,Occurred" bitfld.byte 0x00 1. " INTE ,INTerrupt Enable " "Disabled,Enabled" bitfld.byte 0x00 0. " INT ,INTerrupt" "Not interrupt,Interrupt" if (((per.b(ad:0x3D230000+0x02))&0x40)==0x40) rgroup.byte 0x02++0x00 line.byte 0x00 "I2C3CCR,Clock control register" bitfld.byte 0x00 6. " HSM ,High Speed Mode" "Standard,High-speed mode" bitfld.byte 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.byte 0x00 0.--4. " CS ,Clock Period Select" ",,,,,,,,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32" else rgroup.byte 0x02++0x00 line.byte 0x00 "I2C3CCR,Clock control register" bitfld.byte 0x00 6. " HSM ,High Speed Mode" "Standard,High-speed mode" bitfld.byte 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.byte 0x00 0.--4. " CS ,Clock Period Select" "65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96" endif group.byte 0x03++0x01 line.byte 0x00 "I2C3ADR,Address register" hexmask.byte 0x00 0.--6. 1. " AS ,This is slave address storage bit" line.byte 0x01 "I2C3DAR,Data register" hexmask.byte 0x01 0.--7. 1. " DS ,This is serial data storage bit" group.byte 0x5++0x02 line.byte 0x00 "I2C3CSR,Expand Clock Period Select Register" bitfld.byte 0x00 0.--5. " CS ,Clock Period Select 10-5" "No upper limit,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.byte 0x01 "I2C3FSR,I2C Bus Clock Frequency Register" bitfld.byte 0x01 0.--3. " FS ,Bus Clock Frequency Select" ",14-20,20-40,40-60,60-80,80-100,100-120,120-140,140-160,160-180,180-200,200-220,,,," line.byte 0x02 "I2C3BC2R,Two bus control registers" bitfld.byte 0x02 5. " SDAS ,SDA status" "Low,High" bitfld.byte 0x02 4. " SCLS ,SCL status" "Low,High" bitfld.byte 0x02 1. " SDAL ,SDA low drive" "Normal operation,Forcibly become 'L'" bitfld.byte 0x02 0. " SCLL ,SCL Low drive" "Normal operation,Forcibly become 'L'" width 0xb tree.end tree "I2C ch4" base ad:0x3D240000 width 10. rgroup.byte 0x00++0x00 line.byte 0x00 "I2C4BSR,Bus status register" bitfld.byte 0x00 7. " BB ,Bus busy" "Stop,Start" bitfld.byte 0x00 6. " RSC ,Repeated Start Condition" "Not detected,Detected" bitfld.byte 0x00 5. " AL ,Arbitration Lost" "Not detected,Detected" bitfld.byte 0x00 4. " LRB ,LAST Received Bit" "ACK ,NACK" textline " " bitfld.byte 0x00 3. " TRX ,Transfer/Receive" "Reception state,Transmission state" bitfld.byte 0x00 2. " AAS ,Address As Slave" "Not performed,Performed" bitfld.byte 0x00 1. " GCA ,General Call Address" "Not received,Received" bitfld.byte 0x00 0. " FBT ,First Byte Transfer" "Not first byte,First byte" group.byte 0x01++0x00 line.byte 0x00 "I2C4BCR,Bus control register" bitfld.byte 0x00 7. " BER ,Bus Error" "Not detected,Detected" bitfld.byte 0x00 6. " BEIE ,Bus Error Interrupt Enable" "Prohibited,Permitted" eventfld.byte 0x00 5. " SCC ,Start Condition Continue" "Not available,Start" bitfld.byte 0x00 4. " MSS ,Master Slave Select" "Slave mode,Master mode" textline " " bitfld.byte 0x00 3. " ACK ,ACKnowledge" "Not Occurred,Occurred" bitfld.byte 0x00 2. " GCAA ,General Call Address Acknowledge" "Not Occurred,Occurred" bitfld.byte 0x00 1. " INTE ,INTerrupt Enable " "Disabled,Enabled" bitfld.byte 0x00 0. " INT ,INTerrupt" "Not interrupt,Interrupt" if (((per.b(ad:0x3D240000+0x02))&0x40)==0x40) rgroup.byte 0x02++0x00 line.byte 0x00 "I2C4CCR,Clock control register" bitfld.byte 0x00 6. " HSM ,High Speed Mode" "Standard,High-speed mode" bitfld.byte 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.byte 0x00 0.--4. " CS ,Clock Period Select" ",,,,,,,,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32" else rgroup.byte 0x02++0x00 line.byte 0x00 "I2C4CCR,Clock control register" bitfld.byte 0x00 6. " HSM ,High Speed Mode" "Standard,High-speed mode" bitfld.byte 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.byte 0x00 0.--4. " CS ,Clock Period Select" "65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96" endif group.byte 0x03++0x01 line.byte 0x00 "I2C4ADR,Address register" hexmask.byte 0x00 0.--6. 1. " AS ,This is slave address storage bit" line.byte 0x01 "I2C4DAR,Data register" hexmask.byte 0x01 0.--7. 1. " DS ,This is serial data storage bit" group.byte 0x5++0x02 line.byte 0x00 "I2C4CSR,Expand Clock Period Select Register" bitfld.byte 0x00 0.--5. " CS ,Clock Period Select 10-5" "No upper limit,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.byte 0x01 "I2C4FSR,I2C Bus Clock Frequency Register" bitfld.byte 0x01 0.--3. " FS ,Bus Clock Frequency Select" ",14-20,20-40,40-60,60-80,80-100,100-120,120-140,140-160,160-180,180-200,200-220,,,," line.byte 0x02 "I2C4BC2R,Two bus control registers" bitfld.byte 0x02 5. " SDAS ,SDA status" "Low,High" bitfld.byte 0x02 4. " SCLS ,SCL status" "Low,High" bitfld.byte 0x02 1. " SDAL ,SDA low drive" "Normal operation,Forcibly become 'L'" bitfld.byte 0x02 0. " SCLL ,SCL Low drive" "Normal operation,Forcibly become 'L'" width 0xb tree.end tree.end else tree "I2C BUS interface" tree "I2C ch0" base ad:0x3D200000 width 10. rgroup.long 0x00++0x03 line.long 0x00 "BSR,Bus Status Register" bitfld.long 0x00 7. " BB ,Bus busy" "Stopped,Started" bitfld.long 0x00 6. " RSC ,Repeated start condition" "Not detected,Detected" bitfld.long 0x00 5. " AL ,Arbitration lost" "Not detected,Detected" textline " " bitfld.long 0x00 4. " LRB ,LAST received bit" "ACK,NACK" bitfld.long 0x00 3. " TRX ,Transfer/Receive status" "Reception,Transmission" bitfld.long 0x00 2. " AAS ,Address as slave" "Not performed,Performed" textline " " bitfld.long 0x00 1. " GCA ,General call address" "Not received,Received" bitfld.long 0x00 0. " FBT ,First byte transfer" "Not detected,Detected" group.long 0x04++0x03 line.long 0x00 "BCR,Bus Control Register" bitfld.long 0x00 7. " BER ,Bus error interrupt request flag" "No error,Error" bitfld.long 0x00 6. " BEIE ,Bus error interrupt enable" "Disabled,Enabled" eventfld.long 0x00 5. " SCC ,Start condition continue" ",Generated" textline " " bitfld.long 0x00 4. " MSS ,Master slave select" "Slave mode,Master mode" bitfld.long 0x00 3. " ACK ,Acknowledge permission at receiving data" "Not occurred,Occurred" bitfld.long 0x00 2. " GCAA ,Acknowledge permission bit at receiving general call address" "Not occurred,Occurred" textline " " bitfld.long 0x00 1. " INTE ,Interrupt enable" "Disabled,Enabled" bitfld.long 0x00 0. " INT ,Transfer and interrupt request flag" "Not interrupt,Interrupt" if (((per.l(ad:0x3D200000+0x08))&0x40)==0x40) rgroup.long 0x08++0x03 line.long 0x00 "CCR,Clock Control Register" bitfld.long 0x00 6. " HSM ,High speed mode" "Standard,High-speed" bitfld.long 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.long 0x00 0.--4. " CS ,Clock period select" ",,,,,,,,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32" else rgroup.long 0x08++0x03 line.long 0x00 "CCR,Clock Control Register" bitfld.long 0x00 6. " HSM ,High speed mode" "Standard,High-speed mode" bitfld.long 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.long 0x00 0.--4. " CS ,Clock period select" "65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96" endif group.long 0x0C++0x07 line.long 0x00 "ADR,Address Storage Register" hexmask.long.byte 0x00 0.--6. 1. " AS ,Slave address storage bit" line.long 0x04 "DAR,Data Storage Register" hexmask.long.byte 0x04 0.--7. 1. " DATA ,Serial data storage bit" group.long 0x14++0x0B line.long 0x00 "CSR,Expand Clock Period Select Register" bitfld.long 0x00 0.--5. " CS ,Clock period select 10-5" "No upper limit,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x04 "FSR,I2C Bus Clock Frequency Register" bitfld.long 0x04 0.--3. " FS ,Bus clock frequency select" ",14-20,20-40,40-60,60-80,80-100,100-120,120-140,140-160,160-180,180-200,200-220,?..." line.long 0x08 "BC2R,Bus Control 2 Register" rbitfld.long 0x08 5. " SDAS ,SDA status" "Low,High" rbitfld.long 0x08 4. " SCLS ,SCL status" "Low,High" textline " " bitfld.long 0x08 1. " SDAL ,SDA low drive" "Normal operation,Forced" bitfld.long 0x08 0. " SCLL ,SCL low drive" "Normal operation,Forced" width 0x0B tree.end tree "I2C ch1" base ad:0x3D210000 width 10. rgroup.long 0x00++0x03 line.long 0x00 "BSR,Bus Status Register" bitfld.long 0x00 7. " BB ,Bus busy" "Stopped,Started" bitfld.long 0x00 6. " RSC ,Repeated start condition" "Not detected,Detected" bitfld.long 0x00 5. " AL ,Arbitration lost" "Not detected,Detected" textline " " bitfld.long 0x00 4. " LRB ,LAST received bit" "ACK,NACK" bitfld.long 0x00 3. " TRX ,Transfer/Receive status" "Reception,Transmission" bitfld.long 0x00 2. " AAS ,Address as slave" "Not performed,Performed" textline " " bitfld.long 0x00 1. " GCA ,General call address" "Not received,Received" bitfld.long 0x00 0. " FBT ,First byte transfer" "Not detected,Detected" group.long 0x04++0x03 line.long 0x00 "BCR,Bus Control Register" bitfld.long 0x00 7. " BER ,Bus error interrupt request flag" "No error,Error" bitfld.long 0x00 6. " BEIE ,Bus error interrupt enable" "Disabled,Enabled" eventfld.long 0x00 5. " SCC ,Start condition continue" ",Generated" textline " " bitfld.long 0x00 4. " MSS ,Master slave select" "Slave mode,Master mode" bitfld.long 0x00 3. " ACK ,Acknowledge permission at receiving data" "Not occurred,Occurred" bitfld.long 0x00 2. " GCAA ,Acknowledge permission bit at receiving general call address" "Not occurred,Occurred" textline " " bitfld.long 0x00 1. " INTE ,Interrupt enable" "Disabled,Enabled" bitfld.long 0x00 0. " INT ,Transfer and interrupt request flag" "Not interrupt,Interrupt" if (((per.l(ad:0x3D210000+0x08))&0x40)==0x40) rgroup.long 0x08++0x03 line.long 0x00 "CCR,Clock Control Register" bitfld.long 0x00 6. " HSM ,High speed mode" "Standard,High-speed" bitfld.long 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.long 0x00 0.--4. " CS ,Clock period select" ",,,,,,,,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32" else rgroup.long 0x08++0x03 line.long 0x00 "CCR,Clock Control Register" bitfld.long 0x00 6. " HSM ,High speed mode" "Standard,High-speed mode" bitfld.long 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.long 0x00 0.--4. " CS ,Clock period select" "65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96" endif group.long 0x0C++0x07 line.long 0x00 "ADR,Address Storage Register" hexmask.long.byte 0x00 0.--6. 1. " AS ,Slave address storage bit" line.long 0x04 "DAR,Data Storage Register" hexmask.long.byte 0x04 0.--7. 1. " DATA ,Serial data storage bit" group.long 0x14++0x0B line.long 0x00 "CSR,Expand Clock Period Select Register" bitfld.long 0x00 0.--5. " CS ,Clock period select 10-5" "No upper limit,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x04 "FSR,I2C Bus Clock Frequency Register" bitfld.long 0x04 0.--3. " FS ,Bus clock frequency select" ",14-20,20-40,40-60,60-80,80-100,100-120,120-140,140-160,160-180,180-200,200-220,?..." line.long 0x08 "BC2R,Bus Control 2 Register" rbitfld.long 0x08 5. " SDAS ,SDA status" "Low,High" rbitfld.long 0x08 4. " SCLS ,SCL status" "Low,High" textline " " bitfld.long 0x08 1. " SDAL ,SDA low drive" "Normal operation,Forced" bitfld.long 0x08 0. " SCLL ,SCL low drive" "Normal operation,Forced" width 0x0B tree.end tree "I2C ch2" base ad:0x3D220000 width 10. rgroup.long 0x00++0x03 line.long 0x00 "BSR,Bus Status Register" bitfld.long 0x00 7. " BB ,Bus busy" "Stopped,Started" bitfld.long 0x00 6. " RSC ,Repeated start condition" "Not detected,Detected" bitfld.long 0x00 5. " AL ,Arbitration lost" "Not detected,Detected" textline " " bitfld.long 0x00 4. " LRB ,LAST received bit" "ACK,NACK" bitfld.long 0x00 3. " TRX ,Transfer/Receive status" "Reception,Transmission" bitfld.long 0x00 2. " AAS ,Address as slave" "Not performed,Performed" textline " " bitfld.long 0x00 1. " GCA ,General call address" "Not received,Received" bitfld.long 0x00 0. " FBT ,First byte transfer" "Not detected,Detected" group.long 0x04++0x03 line.long 0x00 "BCR,Bus Control Register" bitfld.long 0x00 7. " BER ,Bus error interrupt request flag" "No error,Error" bitfld.long 0x00 6. " BEIE ,Bus error interrupt enable" "Disabled,Enabled" eventfld.long 0x00 5. " SCC ,Start condition continue" ",Generated" textline " " bitfld.long 0x00 4. " MSS ,Master slave select" "Slave mode,Master mode" bitfld.long 0x00 3. " ACK ,Acknowledge permission at receiving data" "Not occurred,Occurred" bitfld.long 0x00 2. " GCAA ,Acknowledge permission bit at receiving general call address" "Not occurred,Occurred" textline " " bitfld.long 0x00 1. " INTE ,Interrupt enable" "Disabled,Enabled" bitfld.long 0x00 0. " INT ,Transfer and interrupt request flag" "Not interrupt,Interrupt" if (((per.l(ad:0x3D220000+0x08))&0x40)==0x40) rgroup.long 0x08++0x03 line.long 0x00 "CCR,Clock Control Register" bitfld.long 0x00 6. " HSM ,High speed mode" "Standard,High-speed" bitfld.long 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.long 0x00 0.--4. " CS ,Clock period select" ",,,,,,,,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32" else rgroup.long 0x08++0x03 line.long 0x00 "CCR,Clock Control Register" bitfld.long 0x00 6. " HSM ,High speed mode" "Standard,High-speed mode" bitfld.long 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.long 0x00 0.--4. " CS ,Clock period select" "65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96" endif group.long 0x0C++0x07 line.long 0x00 "ADR,Address Storage Register" hexmask.long.byte 0x00 0.--6. 1. " AS ,Slave address storage bit" line.long 0x04 "DAR,Data Storage Register" hexmask.long.byte 0x04 0.--7. 1. " DATA ,Serial data storage bit" group.long 0x14++0x0B line.long 0x00 "CSR,Expand Clock Period Select Register" bitfld.long 0x00 0.--5. " CS ,Clock period select 10-5" "No upper limit,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x04 "FSR,I2C Bus Clock Frequency Register" bitfld.long 0x04 0.--3. " FS ,Bus clock frequency select" ",14-20,20-40,40-60,60-80,80-100,100-120,120-140,140-160,160-180,180-200,200-220,?..." line.long 0x08 "BC2R,Bus Control 2 Register" rbitfld.long 0x08 5. " SDAS ,SDA status" "Low,High" rbitfld.long 0x08 4. " SCLS ,SCL status" "Low,High" textline " " bitfld.long 0x08 1. " SDAL ,SDA low drive" "Normal operation,Forced" bitfld.long 0x08 0. " SCLL ,SCL low drive" "Normal operation,Forced" width 0x0B tree.end tree "I2C ch3" base ad:0x3D230000 width 10. rgroup.long 0x00++0x03 line.long 0x00 "BSR,Bus Status Register" bitfld.long 0x00 7. " BB ,Bus busy" "Stopped,Started" bitfld.long 0x00 6. " RSC ,Repeated start condition" "Not detected,Detected" bitfld.long 0x00 5. " AL ,Arbitration lost" "Not detected,Detected" textline " " bitfld.long 0x00 4. " LRB ,LAST received bit" "ACK,NACK" bitfld.long 0x00 3. " TRX ,Transfer/Receive status" "Reception,Transmission" bitfld.long 0x00 2. " AAS ,Address as slave" "Not performed,Performed" textline " " bitfld.long 0x00 1. " GCA ,General call address" "Not received,Received" bitfld.long 0x00 0. " FBT ,First byte transfer" "Not detected,Detected" group.long 0x04++0x03 line.long 0x00 "BCR,Bus Control Register" bitfld.long 0x00 7. " BER ,Bus error interrupt request flag" "No error,Error" bitfld.long 0x00 6. " BEIE ,Bus error interrupt enable" "Disabled,Enabled" eventfld.long 0x00 5. " SCC ,Start condition continue" ",Generated" textline " " bitfld.long 0x00 4. " MSS ,Master slave select" "Slave mode,Master mode" bitfld.long 0x00 3. " ACK ,Acknowledge permission at receiving data" "Not occurred,Occurred" bitfld.long 0x00 2. " GCAA ,Acknowledge permission bit at receiving general call address" "Not occurred,Occurred" textline " " bitfld.long 0x00 1. " INTE ,Interrupt enable" "Disabled,Enabled" bitfld.long 0x00 0. " INT ,Transfer and interrupt request flag" "Not interrupt,Interrupt" if (((per.l(ad:0x3D230000+0x08))&0x40)==0x40) rgroup.long 0x08++0x03 line.long 0x00 "CCR,Clock Control Register" bitfld.long 0x00 6. " HSM ,High speed mode" "Standard,High-speed" bitfld.long 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.long 0x00 0.--4. " CS ,Clock period select" ",,,,,,,,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32" else rgroup.long 0x08++0x03 line.long 0x00 "CCR,Clock Control Register" bitfld.long 0x00 6. " HSM ,High speed mode" "Standard,High-speed mode" bitfld.long 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.long 0x00 0.--4. " CS ,Clock period select" "65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96" endif group.long 0x0C++0x07 line.long 0x00 "ADR,Address Storage Register" hexmask.long.byte 0x00 0.--6. 1. " AS ,Slave address storage bit" line.long 0x04 "DAR,Data Storage Register" hexmask.long.byte 0x04 0.--7. 1. " DATA ,Serial data storage bit" group.long 0x14++0x0B line.long 0x00 "CSR,Expand Clock Period Select Register" bitfld.long 0x00 0.--5. " CS ,Clock period select 10-5" "No upper limit,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x04 "FSR,I2C Bus Clock Frequency Register" bitfld.long 0x04 0.--3. " FS ,Bus clock frequency select" ",14-20,20-40,40-60,60-80,80-100,100-120,120-140,140-160,160-180,180-200,200-220,?..." line.long 0x08 "BC2R,Bus Control 2 Register" rbitfld.long 0x08 5. " SDAS ,SDA status" "Low,High" rbitfld.long 0x08 4. " SCLS ,SCL status" "Low,High" textline " " bitfld.long 0x08 1. " SDAL ,SDA low drive" "Normal operation,Forced" bitfld.long 0x08 0. " SCLL ,SCL low drive" "Normal operation,Forced" width 0x0B tree.end tree "I2C ch4" base ad:0x3D240000 width 10. rgroup.long 0x00++0x03 line.long 0x00 "BSR,Bus Status Register" bitfld.long 0x00 7. " BB ,Bus busy" "Stopped,Started" bitfld.long 0x00 6. " RSC ,Repeated start condition" "Not detected,Detected" bitfld.long 0x00 5. " AL ,Arbitration lost" "Not detected,Detected" textline " " bitfld.long 0x00 4. " LRB ,LAST received bit" "ACK,NACK" bitfld.long 0x00 3. " TRX ,Transfer/Receive status" "Reception,Transmission" bitfld.long 0x00 2. " AAS ,Address as slave" "Not performed,Performed" textline " " bitfld.long 0x00 1. " GCA ,General call address" "Not received,Received" bitfld.long 0x00 0. " FBT ,First byte transfer" "Not detected,Detected" group.long 0x04++0x03 line.long 0x00 "BCR,Bus Control Register" bitfld.long 0x00 7. " BER ,Bus error interrupt request flag" "No error,Error" bitfld.long 0x00 6. " BEIE ,Bus error interrupt enable" "Disabled,Enabled" eventfld.long 0x00 5. " SCC ,Start condition continue" ",Generated" textline " " bitfld.long 0x00 4. " MSS ,Master slave select" "Slave mode,Master mode" bitfld.long 0x00 3. " ACK ,Acknowledge permission at receiving data" "Not occurred,Occurred" bitfld.long 0x00 2. " GCAA ,Acknowledge permission bit at receiving general call address" "Not occurred,Occurred" textline " " bitfld.long 0x00 1. " INTE ,Interrupt enable" "Disabled,Enabled" bitfld.long 0x00 0. " INT ,Transfer and interrupt request flag" "Not interrupt,Interrupt" if (((per.l(ad:0x3D240000+0x08))&0x40)==0x40) rgroup.long 0x08++0x03 line.long 0x00 "CCR,Clock Control Register" bitfld.long 0x00 6. " HSM ,High speed mode" "Standard,High-speed" bitfld.long 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.long 0x00 0.--4. " CS ,Clock period select" ",,,,,,,,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32" else rgroup.long 0x08++0x03 line.long 0x00 "CCR,Clock Control Register" bitfld.long 0x00 6. " HSM ,High speed mode" "Standard,High-speed mode" bitfld.long 0x00 5. " EN ,Operation enable bit for read/write mode" "Disabled,Enabled" bitfld.long 0x00 0.--4. " CS ,Clock period select" "65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96" endif group.long 0x0C++0x07 line.long 0x00 "ADR,Address Storage Register" hexmask.long.byte 0x00 0.--6. 1. " AS ,Slave address storage bit" line.long 0x04 "DAR,Data Storage Register" hexmask.long.byte 0x04 0.--7. 1. " DATA ,Serial data storage bit" group.long 0x14++0x0B line.long 0x00 "CSR,Expand Clock Period Select Register" bitfld.long 0x00 0.--5. " CS ,Clock period select 10-5" "No upper limit,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x04 "FSR,I2C Bus Clock Frequency Register" bitfld.long 0x04 0.--3. " FS ,Bus clock frequency select" ",14-20,20-40,40-60,60-80,80-100,100-120,120-140,140-160,160-180,180-200,200-220,?..." line.long 0x08 "BC2R,Bus Control 2 Register" rbitfld.long 0x08 5. " SDAS ,SDA status" "Low,High" rbitfld.long 0x08 4. " SCLS ,SCL status" "Low,High" textline " " bitfld.long 0x08 1. " SDAL ,SDA low drive" "Normal operation,Forced" bitfld.long 0x08 0. " SCLL ,SCL low drive" "Normal operation,Forced" width 0x0B tree.end tree.end endif tree "SFI (Serial Flash Interface)" tree "SFI_0" base ad:0x05000000 width 11. group.long 0x00++0x03 line.long 0x00 "SFI0CR,SFI Configuration Register" bitfld.long 0x00 31. " EN ,SFI enable" "Disabled,Enabled" sif (cpuis("MB86R11F")) bitfld.long 0x00 29.--30. " MOD ,SFI mode select" "IO operation,,,SF operation" else bitfld.long 0x00 29.--30. " MOD ,SFI mode select" "IO operation,SF operation,SF operation,SF operation" endif bitfld.long 0x00 24. " CS ,Slave select signal polarity" "Negative,Positive" bitfld.long 0x00 22. " IE6 ,Interrupt enable 6" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " IE5 ,Interrupt enable 5" "Disabled,Enabled" bitfld.long 0x00 20. " IE4 ,Interrupt enable 4" "Disabled,Enabled" bitfld.long 0x00 19. " IE3 ,Interrupt enable 3" "Disabled,Enabled" bitfld.long 0x00 18. " IE2 ,Interrupt enable 2" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " IE1 ,Interrupt enable 1" "Disabled,Enabled" bitfld.long 0x00 16. " IE0 ,Interrupt enable 0" "Disabled,Enabled" bitfld.long 0x00 14. " RDE ,Reception FIFO DMA transfer request enable" "Disabled,Enabled" bitfld.long 0x00 13. " TDE ,Transfer FIFO DMA transfer request enable" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " IMD ,HOLD function enable register" "Disabled,Enabled" hexmask.long.byte 0x00 0.--7. 1. " DIV ,Clock frequency divider" if (((per.l(ad:0x05000000))&0x60000000)==0x00) group.long 0x08++0x07 line.long 0x00 "SFI0SR,SFI Status Register" rbitfld.long 0x00 31. " BSY ,SFI busy" "Not busy,Busy" eventfld.long 0x00 22. " ST6 ,Interrupt status 6" "No interrupt,Interrupt" eventfld.long 0x00 21. " ST5 ,Interrupt status 5" "No interrupt,Interrupt" eventfld.long 0x00 20. " ST4 ,Interrupt status 4" "No interrupt,Interrupt" textline " " eventfld.long 0x00 19. " ST3 ,Interrupt status 3" "No interrupt,Interrupt" rbitfld.long 0x00 18. " ST2 ,Interrupt status 2" "No interrupt,Interrupt" rbitfld.long 0x00 17. " ST1 ,Interrupt status 1" "No interrupt,Interrupt" eventfld.long 0x00 16. " ST0 ,Interrupt status 0" "No interrupt,Interrupt" textline " " rbitfld.long 0x00 8.--12. " RFC ,Reception FIFO counter" "0 byte,,,,1-4 bytes,,,,5~8 bytes,,,,9~12 bytes,,,,13~16 bytes,?..." textline " " rbitfld.long 0x00 0.--4. " TFC ,Transfer FIFO counter" "0 byte,,,,1-4 bytes,,,,5~8 bytes,,,,9~12 bytes,,,,13~16 bytes,?..." group.long 0x10++0x03 line.long 0x00 "SFI0LR,SFI Length Register" bitfld.long 0x00 29.--31. " ADW ,Transfer address width" ",8bit,16bit,24bit,32bit,?..." hexmask.long.word 0x00 16.--27. 1. " RL ,Receive data length" hexmask.long.word 0x00 0.--11. 1. " TL ,Transfer data length" group.long 0x18++0x07 line.long 0x00 "SFI0IR,SFI Instruction Register" bitfld.long 0x00 16.--17. " CS ,Chip select" "SPI0_SS,?..." hexmask.long.byte 0x00 0.--7. 1. " COMMAND ,These bits set output data as a command" line.long 0x04 "SFI0AR,SFI Address Register" hgroup.long 0x20++0x03 hide.long 0x00 "SFI0RF,SFI Receive FIFO" in wgroup.long 0x30++0x03 line.long 0x00 "SFI0TF,SFI Transmit FIFO" hexmask.long.byte 0x00 24.--31. 1. " T3 ,Transfer data 3" hexmask.long.byte 0x00 16.--23. 1. " T2 ,Transfer data 2" hexmask.long.byte 0x00 8.--15. 1. " T1 ,Transfer data 1" hexmask.long.byte 0x00 0.--7. 1. " T0 ,Transfer data 0" else hgroup.long 0x08++0x07 hide.long 0x00 "SFI0SR,SFI Status Register" textline " " textline " " textline " " hgroup.long 0x10++0x03 hide.long 0x00 "SFI0LR,SFI Length Register" hgroup.long 0x18++0x07 hide.long 0x00 "SFI0IR,SFI Instruction Register" hide.long 0x04 "SFI0AR,SFI Address Register" hgroup.long 0x20++0x03 hide.long 0x00 "SFI0RF,SFI Receive FIFO" hgroup.long 0x30++0x03 hide.long 0x00 "SFI0TF,SFI Transmit FIFO" endif width 0x0B tree.end tree "SFI_1" base ad:0x15000000 width 11. group.long 0x00++0x03 line.long 0x00 "SFI0CR,SFI Configuration Register" bitfld.long 0x00 31. " EN ,SFI enable" "Disabled,Enabled" sif (cpuis("MB86R11F")) bitfld.long 0x00 29.--30. " MOD ,SFI mode select" "IO operation,,,SF operation" else bitfld.long 0x00 29.--30. " MOD ,SFI mode select" "IO operation,SF operation,SF operation,SF operation" endif bitfld.long 0x00 24. " CS ,Slave select signal polarity" "Negative,Positive" bitfld.long 0x00 22. " IE6 ,Interrupt enable 6" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " IE5 ,Interrupt enable 5" "Disabled,Enabled" bitfld.long 0x00 20. " IE4 ,Interrupt enable 4" "Disabled,Enabled" bitfld.long 0x00 19. " IE3 ,Interrupt enable 3" "Disabled,Enabled" bitfld.long 0x00 18. " IE2 ,Interrupt enable 2" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " IE1 ,Interrupt enable 1" "Disabled,Enabled" bitfld.long 0x00 16. " IE0 ,Interrupt enable 0" "Disabled,Enabled" bitfld.long 0x00 14. " RDE ,Reception FIFO DMA transfer request enable" "Disabled,Enabled" bitfld.long 0x00 13. " TDE ,Transfer FIFO DMA transfer request enable" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " IMD ,HOLD function enable register" "Disabled,Enabled" hexmask.long.byte 0x00 0.--7. 1. " DIV ,Clock frequency divider" if (((per.l(ad:0x15000000))&0x60000000)==0x00) group.long 0x08++0x07 line.long 0x00 "SFI0SR,SFI Status Register" rbitfld.long 0x00 31. " BSY ,SFI busy" "Not busy,Busy" eventfld.long 0x00 22. " ST6 ,Interrupt status 6" "No interrupt,Interrupt" eventfld.long 0x00 21. " ST5 ,Interrupt status 5" "No interrupt,Interrupt" eventfld.long 0x00 20. " ST4 ,Interrupt status 4" "No interrupt,Interrupt" textline " " eventfld.long 0x00 19. " ST3 ,Interrupt status 3" "No interrupt,Interrupt" rbitfld.long 0x00 18. " ST2 ,Interrupt status 2" "No interrupt,Interrupt" rbitfld.long 0x00 17. " ST1 ,Interrupt status 1" "No interrupt,Interrupt" eventfld.long 0x00 16. " ST0 ,Interrupt status 0" "No interrupt,Interrupt" textline " " rbitfld.long 0x00 8.--12. " RFC ,Reception FIFO counter" "0 byte,,,,1-4 bytes,,,,5~8 bytes,,,,9~12 bytes,,,,13~16 bytes,?..." textline " " rbitfld.long 0x00 0.--4. " TFC ,Transfer FIFO counter" "0 byte,,,,1-4 bytes,,,,5~8 bytes,,,,9~12 bytes,,,,13~16 bytes,?..." group.long 0x10++0x03 line.long 0x00 "SFI0LR,SFI Length Register" bitfld.long 0x00 29.--31. " ADW ,Transfer address width" ",8bit,16bit,24bit,32bit,?..." hexmask.long.word 0x00 16.--27. 1. " RL ,Receive data length" hexmask.long.word 0x00 0.--11. 1. " TL ,Transfer data length" group.long 0x18++0x07 line.long 0x00 "SFI0IR,SFI Instruction Register" bitfld.long 0x00 16.--17. " CS ,Chip select" "SPI0_SS,?..." hexmask.long.byte 0x00 0.--7. 1. " COMMAND ,These bits set output data as a command" line.long 0x04 "SFI0AR,SFI Address Register" hgroup.long 0x20++0x03 hide.long 0x00 "SFI0RF,SFI Receive FIFO" in wgroup.long 0x30++0x03 line.long 0x00 "SFI0TF,SFI Transmit FIFO" hexmask.long.byte 0x00 24.--31. 1. " T3 ,Transfer data 3" hexmask.long.byte 0x00 16.--23. 1. " T2 ,Transfer data 2" hexmask.long.byte 0x00 8.--15. 1. " T1 ,Transfer data 1" hexmask.long.byte 0x00 0.--7. 1. " T0 ,Transfer data 0" else hgroup.long 0x08++0x07 hide.long 0x00 "SFI0SR,SFI Status Register" textline " " textline " " textline " " hgroup.long 0x10++0x03 hide.long 0x00 "SFI0LR,SFI Length Register" hgroup.long 0x18++0x07 hide.long 0x00 "SFI0IR,SFI Instruction Register" hide.long 0x04 "SFI0AR,SFI Address Register" hgroup.long 0x20++0x03 hide.long 0x00 "SFI0RF,SFI Receive FIFO" hgroup.long 0x30++0x03 hide.long 0x00 "SFI0TF,SFI Transmit FIFO" endif width 0x0B tree.end tree.end sif (cpu()=="MB86R11F") tree "USBHC (USB Host Controller)" base ad:0x00800000 width 20. tree "EHCI Operational Registers" rgroup.long 0x00++0x0B line.long 0x00 "HCCAPBASE,EHCI Operational Registers" hexmask.long.word 0x00 16.--31. 1. " HCIVERSION ,EHCI revision number is indicated" hexmask.long.byte 0x00 0.--7. 1. " CAPLENGTH ,Offset of operational register space is indicated" line.long 0x04 "HCSPARAMS,Structural Parameter Register" bitfld.long 0x04 20.--23. " DEBUG_PORT_NUMBER ,The '0' indicating that the macro is not provided with debug ports is read" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x04 16. " P_INDICATOR ,Port Indicator" "Unsupported,Supported" textline " " bitfld.long 0x04 12.--15. " N_CC ,Number of Companion Controller" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x04 8.--11. " N_PCC ,Number of Ports per Companion Controller" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x04 7. " PRR ,Indicates the order in which the ports are routed" "Ascending,Depends on first N_PORTS" bitfld.long 0x04 4. " PPC ,Port Power Control" "Disabled,Enabled" textline " " bitfld.long 0x04 0.--3. " N_PORTS ,Number of accessible port registers in the operational register space" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "HCCPARAMS,Capability Parameter Register" hexmask.long.byte 0x08 8.--15. 1. " EECP ,EHCI Extended Capabilities Pointer" bitfld.long 0x08 4.--7. " IST ,Isochronous Scheduling Threshold" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x08 2. " ASPC ,Asynchronous Schedule Park Capability" "Unsupported,Supported" bitfld.long 0x08 1. " PFLF ,Programmable Frame List Flag" "Fixed to 1024,Frame list size in the USBCMD" textline " " bitfld.long 0x08 0. " AC64 ,Addressing Capability" "32 bits,64 bits" if (((per.l(ad:0x00800000+0x08))&0x06)==0x06) group.long 0x10++0x03 line.long 0x00 "USBCMD,USB Command Register" hexmask.long.byte 0x00 16.--23. 1. " ITC ,Interrupt Threshold Control" bitfld.long 0x00 11. " ASPME ,Asynchronous Schedule Park Mode Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 8.--9. " ASPMC ,Asynchronous Schedule Park Mode Count" ",1,2,3" bitfld.long 0x00 7. " LHCR ,Light Host Controller Reset" "Completed,Reset" textline " " bitfld.long 0x00 6. " IAAD ,Interrupt on Async Advance Doorbell" "No interrupt,Interrupt" bitfld.long 0x00 5. " ASE ,Asynchronous Schedule Enable" "Not processed,Processed" textline " " bitfld.long 0x00 4. " PSE ,Periodic Schedule Enable" "Not processed,Processed" bitfld.long 0x00 2.--3. " FLS ,Frame List Size" "1024 elements,512 elements,256 elements," textline " " bitfld.long 0x00 1. " HCRESET ,Host Controller Reset" "No reset,Reset" bitfld.long 0x00 0. " RS ,Run/Stop" "Stop,Run" elif (((per.l(ad:0x00800000+0x08))&0x06)==0x04) group.long 0x10++0x03 line.long 0x00 "USBCMD,USB Command Register" hexmask.long.byte 0x00 16.--23. 1. " ITC ,Interrupt Threshold Control" bitfld.long 0x00 11. " ASPME ,Asynchronous Schedule Park Mode Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 8.--9. " ASPMC ,Asynchronous Schedule Park Mode Count" ",1,2,3" bitfld.long 0x00 7. " LHCR ,Light Host Controller Reset" "Completed,Reset" textline " " bitfld.long 0x00 6. " IAAD ,Interrupt on Async Advance Doorbell" "No interrupt,Interrupt" bitfld.long 0x00 5. " ASE ,Asynchronous Schedule Enable" "Not processed,Processed" textline " " bitfld.long 0x00 4. " PSE ,Periodic Schedule Enable" "Not processed,Processed" textline " " bitfld.long 0x00 1. " HCRESET ,Host Controller Reset" "No reset,Reset" bitfld.long 0x00 0. " RS ,Run/Stop" "Stop,Run" elif (((per.l(ad:0x00800000+0x08))&0x06)==0x02) group.long 0x10++0x03 line.long 0x00 "USBCMD,USB Command Register" hexmask.long.byte 0x00 16.--23. 1. " ITC ,Interrupt Threshold Control" textline " " bitfld.long 0x00 7. " LHCR ,Light Host Controller Reset" "Completed,Reset" textline " " bitfld.long 0x00 6. " IAAD ,Interrupt on Async Advance Doorbell" "No interrupt,Interrupt" bitfld.long 0x00 5. " ASE ,Asynchronous Schedule Enable" "Not processed,Processed" textline " " bitfld.long 0x00 4. " PSE ,Periodic Schedule Enable" "Not processed,Processed" bitfld.long 0x00 2.--3. " FLS ,Frame List Size" "1024 elements,512 elements,256 elements," textline " " bitfld.long 0x00 1. " HCRESET ,Host Controller Reset" "No reset,Reset" bitfld.long 0x00 0. " RS ,Run/Stop" "Stop,Run" else group.long 0x10++0x03 line.long 0x00 "USBCMD,USB Command Register" hexmask.long.byte 0x00 16.--23. 1. " ITC ,Interrupt Threshold Control" textline " " bitfld.long 0x00 7. " LHCR ,Light Host Controller Reset" "Completed,Reset" textline " " bitfld.long 0x00 6. " IAAD ,Interrupt on Async Advance Doorbell" "No interrupt,Interrupt" bitfld.long 0x00 5. " ASE ,Asynchronous Schedule Enable" "Not processed,Processed" textline " " bitfld.long 0x00 4. " PSE ,Periodic Schedule Enable" "Not processed,Processed" textline " " bitfld.long 0x00 1. " HCRESET ,Host Controller Reset" "No reset,Reset" bitfld.long 0x00 0. " RS ,Run/Stop" "Stop,Run" endif group.long 0x14++0x17 line.long 0x00 "USBSTS,USB Status Register" rbitfld.long 0x00 15. " ASS ,Asynchronous Schedule Status" "Disabled,Enabled" rbitfld.long 0x00 14. " PSS ,Periodic Schedule Status" "Disabled,Enabled" textline " " rbitfld.long 0x00 13. " Reclamation ,Whether the Asynchronous Schedule is empty is indicated" "No,Yes" rbitfld.long 0x00 12. " HcHalted ,Host controler process Run/Stop" "Stop,Run" textline " " eventfld.long 0x00 5. " IAA ,Interrupt on Async Advance" "No interrupt,Interrupt" eventfld.long 0x00 4. " HSE ,Host System Error" "No error,Error" textline " " eventfld.long 0x00 3. " FLR ,Frame List Rollover" "0,1" eventfld.long 0x00 2. " PCD ,Port Change Detect" "0,1" textline " " eventfld.long 0x00 1. " USBERRINT ,USB Error Interrupt" "No interrupt,Interrupt" eventfld.long 0x00 0. " USBINT ,USBINT" "Not completed,Completed" line.long 0x04 "USBINTR,USB Interrupt Enable Register" bitfld.long 0x04 5. " IAAE ,Interrupt on Async Advance Enable" "Disabled,Enabled" bitfld.long 0x04 4. " HSEE ,Host System Error Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 3. " FLRE ,Frame List Rollover Enable" "Disabled,Enabled" bitfld.long 0x04 2. " PCIE ,Port Change Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 1. " USBEIE ,USB Error Interrupt Enable" "Disabled,Enabled" bitfld.long 0x04 0. " USBIE ,USB Interrupt Enable" "Disabled,Enabled" line.long 0x08 "FRINDEX,USB Frame Index Register" hexmask.long.word 0x08 0.--13. 1. " FRAME_INDEX ,Value of the register is incremented at the end of each frame" line.long 0x0C "CTRLDSSEGMENT,4G Segment Selector Register" line.long 0x10 "PERIODICLISTBASE,Periodic Frame List Base Address Register" hexmask.long.tbyte 0x10 12.--31. 0x1000 " PERIODICLISTBASE ,Base address of Periodic Frame List in the memory area is set" line.long 0x14 "ASYNCLISTADDR,Asynchronous List Address Register" hexmask.long 0x14 5.--31. 0x20 " LINK_POINTER_LOW ,Queue head address of the Asynchronous Schedule to be executed next is stored" group.long 0x50++0x03 line.long 0x00 "CONFIGFLAG,Configured Flag Register" bitfld.long 0x00 0. " CF ,Configure flag" "OHCI,EHCI" if (((per.l(ad:0x00800000+0x04))&0x10010)==0x10010)&&(((per.l(ad:0x00800000+0x54))&0x04)==0x04) group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " bitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Off,On" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " Suspend ,Suspend" "Enabled,Suspended" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " Port_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" elif (((per.l(ad:0x00800000+0x04))&0x10010)==0x10010)&&(((per.l(ad:0x00800000+0x54))&0x04)==0x00) group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " bitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Off,On" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " Suspend ,Suspend" "Disabled,Disabled" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " Port_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" elif (((per.l(ad:0x00800000+0x04))&0x10010)==0x10)&&(((per.l(ad:0x00800000+0x54))&0x04)==0x04) group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " rbitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Off,On" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " SUSPEND ,Suspend" "Enabled,Suspended" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " Port_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" elif (((per.l(ad:0x00800000+0x04))&0x10010)==0x10)&&(((per.l(ad:0x00800000+0x54))&0x04)==0x00) group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " rbitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Off,On" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " SUSPEND ,Suspend" "Disabled,Disabled" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " PORT_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" elif (((per.l(ad:0x00800000+0x04))&0x10010)==0x10000)&&(((per.l(ad:0x00800000+0x54))&0x04)==0x04) group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " bitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Unable,Unable" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " SUSPEND ,Suspend" "Enabled,Suspended" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " PORT_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" elif (((per.l(ad:0x00800000+0x04))&0x10010)==0x10000)&&(((per.l(ad:0x00800000+0x54))&0x04)==0x00) group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " bitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Unable,Unable" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " SUSPEND ,Suspend" "Disabled,Disabled" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " PORT_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" elif (((per.l(ad:0x00800000+0x04))&0x10010)==0x00)&&(((per.l(ad:0x00800000+0x54))&0x04)==0x04) group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " rbitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Unable,Unable" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " SUSPEND ,Suspend" "Enabled,Suspended" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " PORT_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" else group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " rbitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Unable,Unable" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " SUSPEND ,Suspend" "Disabled,Disabled" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " PORT_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" endif group.long 0x90++0x0B line.long 0x00 "INSNREG00,Programmable Microframe Base Value Register" hexmask.long.word 0x00 1.--13. 1. " LMF ,The length of 1 micro frame is set" bitfld.long 0x00 0. " REGFCND/E ,This register function is enabled" "Disabled,Enabled" line.long 0x04 "INSNREG01,Programmable Packet Buffer OUT/IN Threshold Register" hexmask.long.word 0x04 16.--31. 1. " OUT_THRESHOLD ,Host Controller transfer to USB" hexmask.long.word 0x04 0.--15. 1. " IN_THRESHOLD ,Host Controller transfer to memory" line.long 0x08 "INSNREG02,Programmable Packet Buffer Depth Register" hexmask.word 0x08 0.--11. 1. " INSNREG02 ,Packet buffer depth is defined in DWORD unit" hgroup.long 0x9C++0x03 hide.long 0x00 "INSNREG03,Time-Available Offset Register" group.long 0xA0++0x03 line.long 0x00 "INSNREG04,Debug Register" bitfld.long 0x00 4. " NAK_EN ,NAK reload fix is controlled" "Enabled,Disabled" bitfld.long 0x00 2. " PORT_ENUM ,Measurement function at the port enumeration time" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " WRITE_CTRL_FAC ,Writing control function of HCCPARAMS" "Not possible,Possible" bitfld.long 0x00 0. " WRITE_CTRL_FUNC ,Writing control function of HCSPARAMS" "Not possible,Possible" tree.end base ad:0x00800200 tree "OHCI Operational Registers" width 20. rgroup.long 0x00++0x03 line.long 0x00 "HCREVISION,Revision Register" hexmask.long.byte 0x00 0.--7. 1. " REV ,Version of OHCI specification is indicated" group.long 0x04++0x1F line.long 0x00 "HCCONTROL,Control Register" bitfld.long 0x00 10. " RWE ,Remote Wake up Enable" "Disabled,Enabled" bitfld.long 0x00 9. " RWC ,Remote Wake up Connected" "No supported,Supported" textline " " bitfld.long 0x00 8. " IR ,Interrupt Routing" "INT,SMI" bitfld.long 0x00 6.--7. " HCFS ,Host Controller Functional State" "USB Reset,USB Resume,USB Operational,USB Suspend" textline " " bitfld.long 0x00 5. " BLE ,Bulk List Enable" "Disabled,Enabled" bitfld.long 0x00 4. " CLE ,Control List Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " IE ,Isochronous Enable" "Disabled,Enabled" bitfld.long 0x00 2. " PLE ,Periodic List Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0.--1. " CBSR ,Control Bulk Service Ratio" "1 Endpoint,2 Endpoint,3 Endpoint,4 Endpoint" line.long 0x04 "HCCOMMANDSTATUS,Command/Status Register" rbitfld.long 0x04 16.--17. " SOC ,Scheduling Overrun Count" "0,1,2,3" bitfld.long 0x04 3. " OCR ,Ownership Change Request" "Not set,Set" textline " " bitfld.long 0x04 2. " BLF ,Bulk List Filled" "Processed,Processing" bitfld.long 0x04 1. " CLF ,Control List Filled" "Processed,Processing" textline " " bitfld.long 0x04 0. " HCR ,Host Controller Reset" "No reset,Reset" line.long 0x08 "HCINTERRUPTSTATUS,Interrupt Status Register" bitfld.long 0x08 30. " OC ,Ownership Change" "Not set,Set" bitfld.long 0x08 6. " RHSC ,Root Hub Status Change" "Not changed,Changed" textline " " bitfld.long 0x08 5. " FNO ,Frame Number Overflow" "Not overflow,Overflow" bitfld.long 0x08 4. " UE ,Unrecoverable Error" "Not set,Set" textline " " bitfld.long 0x08 3. " RD ,Resume Detected" "Not detected,Detected" bitfld.long 0x08 2. " SF ,Startof Frame" "Not blocked,Blocked" textline " " bitfld.long 0x08 1. " WDH ,Write back Done Head" "Not completed,Completed" bitfld.long 0x08 0. " SO ,Scheduling Overrun" "Not detected,Detected" line.long 0x0C "HCINTERRUPTENABLE,Interrupt Enable Register" bitfld.long 0x0C 31. " MIE ,Master Interrupt Enable" "Disabled,Enabled" bitfld.long 0x0C 30. " OC ,Ownership Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x0C 6. " RHSC ,Root Hub Status Change Enable" "Disabled,Enabled" bitfld.long 0x0C 5. " FNO ,Frame Number Overflow Enable" "Disabled,Enabled" textline " " bitfld.long 0x0C 4. " UE ,Unrecoverable Error Enable" "Disabled,Enabled" bitfld.long 0x0C 3. " RD ,Resume Detected Enable" "Disabled,Enabled" textline " " bitfld.long 0x0C 2. " SF ,Start Of Frame Enable" "Disabled,Enabled" bitfld.long 0x0C 1. " WDH ,Write back Done Head Enable" "Disabled,Enabled" textline " " bitfld.long 0x0C 0. " SO ,Scheduling Overrun Enable" "Disabled,Enabled" line.long 0x10 "HCINTERRUPTDISABLE,Interrupt Disable Register" bitfld.long 0x10 31. " MIE ,Master Interrupt Disable" "No,Yes" bitfld.long 0x10 30. " OC ,Ownership Change Disable" "No,Yes" textline " " bitfld.long 0x10 6. " RHSC ,Root Hub Status Change Disable" "No,Yes" bitfld.long 0x10 5. " FNO ,Frame Number Overflow Disable" "No,Yes" textline " " bitfld.long 0x10 4. " UE ,Unrecoverable Error Disable" "No,Yes" bitfld.long 0x10 3. " RD ,Resume Detected Disable" "No,Yes" textline " " bitfld.long 0x10 2. " SF ,Start Of Frame Disable" "No,Yes" bitfld.long 0x10 1. " WDH ,Write back Done Head Disable" "No,Yes" textline " " bitfld.long 0x10 0. " SO ,Scheduling Overrun Disable" "No,Yes" line.long 0x14 "HCHCCA,HCCA Register" hexmask.long.tbyte 0x14 8.--31. 1. " HCCA ,This is a pointer to the HCCA base address" line.long 0x18 "HCPERIODCURRENTED,Periodic Current ED Register" hexmask.long 0x18 4.--31. 0x10 " PCED ,This is a pointer to the current Periodic list ED" line.long 0x1C "HCCONTROLHEADED,Control Head ED Register" hexmask.long 0x1C 4.--31. 0x10 " CHED ,This is a pointer to the Control List Head ED" if (((per.l(ad:0x00800000+0x204))&0x10)==0x0) group.long 0x24++0x03 line.long 0x00 "HCCONTROLCURRENTED,Control Current ED Register" hexmask.long 0x00 4.--31. 0x10 " CCED ,This is a pointer to the current Control list ED" else rgroup.long 0x24++0x03 line.long 0x00 "HCCONTROLCURRENTED,Control Current ED Register" hexmask.long 0x00 4.--31. 0x10 " CCED ,This is a pointer to the current Control list ED" endif group.long 0x28++0x03 line.long 0x00 "HCBULKHEADED,Bulk Head ED Register" hexmask.long 0x00 4.--31. 0x10 " BHED ,This is a pointer to the Bulk List Head ED" if (((per.l(ad:0x00800000+0x204))&0x10)==0x0) group.long 0x2C++0x03 line.long 0x00 "HCBULKCURRENTED,Bulk Current ED Register" hexmask.long 0x00 4.--31. 0x10 " BCED ,This is a pointer to the current Bulk list ED" else rgroup.long 0x2C++0x03 line.long 0x00 "HCBULKCURRENTED,Bulk Current ED Register" hexmask.long 0x00 4.--31. 0x10 " BCED ,This is a pointer to the current Bulk list ED" endif group.long 0x30++0x03 line.long 0x00 "HCDONEHEAD,Done Head Register" hexmask.long 0x00 4.--31. 0x10 " DH ,This is a pointer to the Done Head ED" group.long 0x34++0x03 line.long 0x00 "HCFMINTERVAL,Frame Interval Register" bitfld.long 0x00 31. " FIT ,Frame Interval Toggle" "0,1" hexmask.long.word 0x00 16.--30. 1. " FSMPS ,FS Largest Data Packet" textline " " hexmask.long.word 0x00 0.--13. 1. " FI ,This field specifies the length of the frame" rgroup.long 0x38++0x07 line.long 0x00 "HCFMREMAINING,Frame Remaining Register" bitfld.long 0x00 31. " FRT ,Frame Remaining Toggle" "0,1" hexmask.long.word 0x00 0.--13. 1. " FR ,Frame Remaining" line.long 0x04 "HCFMNUMBER,Frame Number Register" hexmask.long.word 0x04 0.--15. 1. " FN ,Frame Number" group.long 0x40++0x07 line.long 0x00 "HCPERIODICSTART,Periodic Start Register" hexmask.long.word 0x00 0.--13. 1. " PS ,This field does the time setting that Host Controller starts the processing of Periodic list in the frame" line.long 0x04 "HCLSTHRESHOLD,LS Threshold Register" hexmask.long.word 0x04 0.--11. 1. " LST ,LS Threshold" if ((((per.l(ad:0x00800000+0x248))&0x1000)==0x00)&&(((per.l(ad:0x00800000+0x248))&0x200)==0x00)) group.long 0x48++0x03 line.long 0x00 "HCRHDESCRIPTORA,Root Hub Descriptor A Register" hexmask.long.byte 0x00 24.--31. 1. " POTPGT ,Power On To Power Good Time" bitfld.long 0x00 12. " NOCP ,No OverCurrent Protection" "Reported,Not reported" textline " " bitfld.long 0x00 11. " OCPM ,OverCurrent Protection Mode" "Global,Individual" bitfld.long 0x00 10. " DT ,Device Type" "0,1" textline " " bitfld.long 0x00 9. " NPS ,No Power Switching" "No,Yes" bitfld.long 0x00 8. " PSM ,Power Switching Mode" "Global,Individual" textline " " hexmask.long.byte 0x00 0.--7. 1. " NDP ,Number Downstream Ports" elif ((((per.l(ad:0x00800000+0x248))&0x1000)==0x1000)&&(((per.l(ad:0x00800000+0x248))&0x200)==0x00)) group.long 0x48++0x03 line.long 0x00 "HCRHDESCRIPTORA,Root Hub Descriptor A Register" hexmask.long.byte 0x00 24.--31. 1. " POTPGT ,Power On To Power Good Time" bitfld.long 0x00 12. " NOCP ,No OverCurrent Protection" "Reported,Not reported" textline " " bitfld.long 0x00 10. " DT ,Device Type" "0,1" textline " " bitfld.long 0x00 9. " NPS ,No Power Switching" "No,Yes" bitfld.long 0x00 8. " PSM ,Power Switching Mode" "Global,Individual" textline " " hexmask.long.byte 0x00 0.--7. 1. " NDP ,Number Downstream Ports" elif ((((per.l(ad:0x00800000+0x248))&0x1000)==0x00)&&(((per.l(ad:0x00800000+0x248))&0x200)==0x200)) group.long 0x48++0x03 line.long 0x00 "HCRHDESCRIPTORA,Root Hub Descriptor A Register" hexmask.long.byte 0x00 24.--31. 1. " POTPGT ,Power On To Power Good Time" bitfld.long 0x00 12. " NOCP ,No OverCurrent Protection" "Reported,Not reported" textline " " bitfld.long 0x00 11. " OCPM ,OverCurrent Protection Mode" "Global,Individual" bitfld.long 0x00 10. " DT ,Device Type" "0,1" textline " " bitfld.long 0x00 9. " NPS ,No Power Switching" "No,Yes" textline " " hexmask.long.byte 0x00 0.--7. 1. " NDP ,Number Downstream Ports" else group.long 0x48++0x03 line.long 0x00 "HCRHDESCRIPTORA,Root Hub Descriptor A Register" hexmask.long.byte 0x00 24.--31. 1. " POTPGT ,Power On To Power Good Time" bitfld.long 0x00 12. " NOCP ,No OverCurrent Protection" "Reported,Not reported" textline " " bitfld.long 0x00 10. " DT ,Device Type" "0,1" textline " " bitfld.long 0x00 9. " NPS ,No Power Switching" "No,Yes" textline " " hexmask.long.byte 0x00 0.--7. 1. " NDP ,Number Downstream Ports" endif if ((((per.l(ad:0x00800000+0x248))&0x200)==0x00)&&(((per.l(ad:0x00800000+0x248))&0x100)==0x100)) group.long 0x4C++0x03 line.long 0x00 "HCRHDESCRIPTORB,Root Hub Descriptor B Register" bitfld.long 0x00 18. " PPCM2 , Port Power Control Mask" "Influenced,Not influenced" bitfld.long 0x00 17. " PPCM1 , Port Power Control Mask" "Influenced,Not influenced" textline " " bitfld.long 0x00 2. " DR2 ,Device on Port 2 Removable" "Removable,Not removable" bitfld.long 0x00 1. " DR1 ,Device on Port 1 Removable" "Removable,Not removable" else group.long 0x4C++0x03 line.long 0x00 "HCRHDESCRIPTORB,Root Hub Descriptor B Register" bitfld.long 0x00 2. " DR2 ,Device on Port 2 Removable" "Removable,Not removable" bitfld.long 0x00 1. " DR1 ,Device on Port 1 Removable" "Removable,Not removable" endif if ((((per.l(ad:0x00800000+0x248))&0x1000)==0x00)&&(((per.l(ad:0x00800000+0x248))&0x800)==0x00)) group.long 0x50++0x03 line.long 0x00 "HCRHSTATUS,Root Hub Status Register" bitfld.long 0x00 17. " OCIC ,OverCurrent Indicator Change" "Disabled,Cleared" bitfld.long 0x00 16. " LPSC ,Local Power Status Change" "Not set,Set" textline " " setclrfld.long 0x00 15. 0x00 15. 0x00 31. " DRWE_set/clr ,Device Remote Wake up Enable" "Not set,set" rbitfld.long 0x00 1. " OCI ,OverCurrent Indicator" "Not detected,Detected" textline " " bitfld.long 0x00 0. " LPS ,Local Power Status" "Not cleared,Cleared" else group.long 0x50++0x03 line.long 0x00 "HCRHSTATUS,Root Hub Status Register" bitfld.long 0x00 17. " OCIC ,OverCurrent Indicator Change" "Disabled,Cleared" bitfld.long 0x00 16. " LPSC ,Local Power Status Change" "Not set,Set" textline " " setclrfld.long 0x00 15. 0x00 15. 0x00 31. " DRWE_SET/CLR ,Device Remote Wake up Enable" "Not set,set" textline " " bitfld.long 0x00 0. " LPS ,Local Power Status" "Not cleared,Cleared" endif textline " " if (((per.l(ad:0x00800000+0x254))&0x01)==0x01) if ((((per.l(ad:0x00800000+0x248))&0x800)==0x800)&&(((per.l(ad:0x00800000+0x248))&0x1000)==0x00)) group.long 0x54++0x03 line.long 0x00 "HCRHPORTSTATUS[1],Root Hub Port Status/Control Register 1" bitfld.long 0x00 20. " PRSC ,Port Reset Status Change R/W" "Not resumed/Disabled,Completed/Cleared" bitfld.long 0x00 19. " OCIC ,Port OverCurrent Indicator Change R/W" "Not resumed/Disabled,Ended/Cleared" textline " " bitfld.long 0x00 18. " PSSC ,Port Suspend Status Change R/W" "Not resumed/Disabled,Ended/Cleared" bitfld.long 0x00 17. " PESC ,Port Enable Status Change R/W" "Not Changed/Disabled,Changed/Cleared" textline " " bitfld.long 0x00 16. " CSC ,Connect Status Change R/W" "No connection/Disabled,Connection/Cleared" bitfld.long 0x00 9. " LSDA ,Low Speed Device Attached R/W" "Full/Disabled,Low/Cleared" textline " " bitfld.long 0x00 8. " PPS ,Port Power Status R/W" "Off/Disabled,On/Set" bitfld.long 0x00 4. " PRS ,Port Reset Status R/W" "Not active/Disabled,Active/Set" textline " " bitfld.long 0x00 3. " POCI ,Port OverCurrent Indicator R/W" "Normal current/Disabled,Over-current/Resume processing" bitfld.long 0x00 2. " PSS ,Port Suspend Status R/W" "Not suspended/Disabled,Suspended/Set" textline " " bitfld.long 0x00 1. " PES ,Port Enable Status R/W" "Disabled/Disabled,Enabled/Set" bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected/Disabled,Connected/Cleared" else group.long 0x54++0x03 line.long 0x00 "HCRHPORTSTATUS[1],Root Hub Port Status/Control Register 1" bitfld.long 0x00 20. " PRSC ,Port Reset Status Change R/W" "Not resumed/Disabled,Completed/Cleared" bitfld.long 0x00 19. " OCIC ,Port OverCurrent Indicator Change R/W" "Not resumed/Disabled,Ended/Cleared" textline " " bitfld.long 0x00 18. " PSSC ,Port Suspend Status Change R/W" "Not resumed/Disabled,Ended/Cleared" bitfld.long 0x00 17. " PESC ,Port Enable Status Change R/W" "Not Changed/Disabled,Changed/Cleared" textline " " bitfld.long 0x00 16. " CSC ,Connect Status Change R/W" "No connection/Disabled,Connection/Cleared" bitfld.long 0x00 9. " LSDA ,Low Speed Device Attached R/W" "Full/Disabled,Low/Cleared" textline " " bitfld.long 0x00 8. " PPS ,Port Power Status R/W" "Off/Disabled,On/Set" bitfld.long 0x00 4. " PRS ,Port Reset Status R/W" "Not active/Disabled,Active/Set" textline " " bitfld.long 0x00 2. " PSS ,Port Suspend Status R/W" "Not suspended/Disabled,Suspended/Set" textline " " bitfld.long 0x00 1. " PES ,Port Enable Status R/W" "Disabled/Disabled,Enabled/Set" bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected/Disabled,Connected/Cleared" endif else if ((((per.l(ad:0x00800000+0x248))&0x800)==0x800)&&(((per.l(ad:0x00800000+0x248))&0x1000)==0x00)) group.long 0x54++0x03 line.long 0x00 "HCRHPORTSTATUS[1],Root Hub Port Status/Control Register 1" bitfld.long 0x00 20. " PRSC ,Port Reset Status Change R/W" "Not resumed/Disabled,Completed/Cleared" bitfld.long 0x00 19. " OCIC ,Port OverCurrent Indicator Change R/W" "Not resumed/Disabled,Ended/Cleared" textline " " bitfld.long 0x00 18. " PSSC ,Port Suspend Status Change R/W" "Not resumed/Disabled,Ended/Cleared" bitfld.long 0x00 17. " PESC ,Port Enable Status Change R/W" "Not Changed/Disabled,Changed/Cleared" textline " " bitfld.long 0x00 16. " CSC ,Connect Status Change R/W" "No connection/Disabled,Connection/Cleared" textline " " bitfld.long 0x00 8. " PPS ,Port Power Status R/W" "Off/Disabled,On/Set" bitfld.long 0x00 4. " PRS ,Port Reset Status R/W" "Not active/Disabled,Active/Set" textline " " bitfld.long 0x00 3. " POCI ,Port OverCurrent Indicator R/W" "Normal current/Disabled,Over-current/Resume processing" bitfld.long 0x00 2. " PSS ,Port Suspend Status R/W" "Not suspended/Disabled,Suspended/Set" textline " " bitfld.long 0x00 1. " PES ,Port Enable Status R/W" "Disabled/Disabled,Enabled/Set" bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected/Disabled,Connected/Cleared" else group.long 0x54++0x03 line.long 0x00 "HCRHPORTSTATUS[1],Root Hub Port Status/Control Register 1" bitfld.long 0x00 20. " PRSC ,Port Reset Status Change R/W" "Not resumed/Disabled,Completed/Cleared" bitfld.long 0x00 19. " OCIC ,Port OverCurrent Indicator Change R/W" "Not resumed/Disabled,Ended/Cleared" textline " " bitfld.long 0x00 18. " PSSC ,Port Suspend Status Change R/W" "Not resumed/Disabled,Ended/Cleared" bitfld.long 0x00 17. " PESC ,Port Enable Status Change R/W" "Not Changed/Disabled,Changed/Cleared" textline " " bitfld.long 0x00 16. " CSC ,Connect Status Change R/W" "No connection/Disabled,Connection/Cleared" textline " " bitfld.long 0x00 8. " PPS ,Port Power Status R/W" "Off/Disabled,On/Set" bitfld.long 0x00 4. " PRS ,Port Reset Status R/W" "Not active/Disabled,Active/Set" textline " " bitfld.long 0x00 2. " PSS ,Port Suspend Status R/W" "Not suspended/Disabled,Suspended/Set" textline " " bitfld.long 0x00 1. " PES ,Port Enable Status R/W" "Disabled/Disabled,Enabled/Set" bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected/Disabled,Connected/Cleared" endif endif tree.end base ad:0x00800400 width 17. tree "Other Registers" group.long 0x00++0x0B line.long 0x00 "LINKMODESETTING,Link Mode Setting Register" hexmask.long.byte 0x00 24.--31. 1. " PHY_VSTATUS ,Vendor Status" bitfld.long 0x00 23. " SS_ULPI_PP2VBUS ,LINK mode setting" "0,1" textline " " bitfld.long 0x00 22. " SS_AUTOPPD_ON_OVERCUR_EN ,LINK mode setting" "0,1" textline " " bitfld.long 0x00 16.--21. " SS_FLADJ_VAL ,Frame Length Adjustment Register Per Port" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 10.--15. " SS_FLADJ_VAL_HOST ,The frame length is adjusted" "59488,59504,59520,59536,59552,59568,59584,59600,59616,59632,59648,59664,59680,59696,59712,59728,59744,59760,59776,59792,59808,59824,59840,59856,59872,59888,59904,59920,59936,59952,59968,59984,60000,60016,60032,60048,60064,60080,60096,60112,60128,60144,60160,60176,60192,60208,60224,60240,60256,60272,60288,60304,60320,60336,60352,60368,60384,60400,60416,60432,60448,60464,60480,60496" textline " " bitfld.long 0x00 9. " SS_SIMULATION_MODE ,Simulation mode signal" "Normal,Simulation" bitfld.long 0x00 8. " SS_WORLD_IF ,Word interface" "16 bit,8 bit" textline " " bitfld.long 0x00 7. " SS_NXT_POWER_STATE_VALID ,LINK mode setting" "0,1" bitfld.long 0x00 6. " SS_POWER_STATE_VALID ,LINK mode setting" "0,1" textline " " bitfld.long 0x00 4.--5. " SS_NEXT_POWER_STATE ,LINK mode setting" "0,1,2,3" bitfld.long 0x00 2.--3. " SS_POWER_STATE ,LINK mode setting" "0,1,2,3" textline " " bitfld.long 0x00 1. " SS_RESUME_UTMI_PLS_DIS ,Signal for debugging" "0,1" bitfld.long 0x00 0. " SS_UTMI_BACKWARD_ENB ,Signal for debugging" "0,1" line.long 0x04 "PHYMODESETTING1,PHY Mode Setting 1 Register" bitfld.long 0x04 31. " RESET ,PHY block part reset signal" "No reset,Reset" bitfld.long 0x04 27. " SIM ,Input of simulation time reduction mode" "Normal,Reduced" textline " " bitfld.long 0x04 26. " ANPD ,PHY block analog circuit power-down signal" "Not set,Set" bitfld.long 0x04 25. " RPDMEN ,D- pull-down resistor on/off control signal" "Off,On" textline " " bitfld.long 0x04 24. " RPDPEN ,D+ pull-down resistor on/off control signal" "Off,On" bitfld.long 0x04 23. " ENVDETSEL1 ,PHY mode setting" "0,1" textline " " bitfld.long 0x04 22. " ENVDETSEL0 ,PHY mode setting" "0,1" bitfld.long 0x04 21. " HSDTRSELS ,PHY mode setting" "0,1" textline " " bitfld.long 0x04 20. " HSDTRSELF ,PHY mode setting" "0,1" bitfld.long 0x04 19. " CRYCNTENX ,PHY mode setting" "0,1" textline " " bitfld.long 0x04 18. " CLKSEL1 ,PHY mode setting" "0,1" bitfld.long 0x04 17. " CLKSEL0 ,PHY mode setting" "0,1" textline " " bitfld.long 0x04 16. " PSWENX ,PHY mode setting" "0,1" bitfld.long 0x04 14. " EOP_TIMER_EN ,PHY mode setting" "0,1" textline " " bitfld.long 0x04 9. " CONTCDR ,PHY mode setting" "0,1" bitfld.long 0x04 4. " ENFLTR ,PHY mode setting" "0,1" textline " " bitfld.long 0x04 3. " RPUENXEN ,PHY mode setting" "0,1" bitfld.long 0x04 2. " RPUEN2 ,PHY mode setting" "0,1" textline " " bitfld.long 0x04 0. " DBUS16 ,PHY mode setting" "0,1" line.long 0x08 "PHYMODESETTING2,PHY Mode Setting 2 Register" rbitfld.long 0x08 30. " COMPMEASREG3 ,COMPMEASREG3" "0,1" rbitfld.long 0x08 29. " COMPMEASREG2 ,COMPMEASREG2" "0,1" textline " " rbitfld.long 0x08 28. " COMPMEASREG1 ,COMPMEASREG1" "0,1" bitfld.long 0x08 26. " COMPTEST3 ,PHY mode setting" "0,1" textline " " bitfld.long 0x08 25. " COMPTEST2 ,PHY mode setting" "0,1" bitfld.long 0x08 24. " COMPTEST1 ,PHY mode setting" "0,1" textline " " bitfld.long 0x08 23. " COMPTESTSEL ,PHY mode setting" "0,1" bitfld.long 0x08 21. " EARLYSYNC ,PHY mode setting" "0,1" textline " " bitfld.long 0x08 20. " REFLMASK ,PHY mode setting" "0,1" bitfld.long 0x08 19. " HSDSEL1 ,PHY mode setting" "0,1" textline " " bitfld.long 0x08 18. " HSDSEL0 ,PHY mode setting" "0,1" bitfld.long 0x08 17. " SQSEL ,PHY mode setting" "0,1" textline " " hexmask.long.byte 0x08 8.--14. 1. " COMPDISCON ,PHY mode setting" bitfld.long 0x08 7. " COMPUPDPLS ,PHY mode setting" "0,1" textline " " bitfld.long 0x08 5. " COMPUPDCTL3 ,PHY mode setting" "0,1" bitfld.long 0x08 4. " COMPUPDCTL2 ,PHY mode setting" "0,1" textline " " bitfld.long 0x08 3. " COMPUPDCTL1 ,PHY mode setting" "0,1" bitfld.long 0x08 0.--2. " LEOP ,PHY mode setting" "0,1,2,3,4,5,6,7" tree.end width 0x0B tree.end tree "USB HOST/FUNC Controller" base ad:0x00810000 width 20. tree "EHCI Operational Registers" rgroup.long 0x00++0x0B line.long 0x00 "HCCAPBASE,EHCI Operational Registers" hexmask.long.word 0x00 16.--31. 1. " HCIVERSION ,EHCI revision number is indicated" hexmask.long.byte 0x00 0.--7. 1. " CAPLENGTH ,Offset of operational register space is indicated" line.long 0x04 "HCSPARAMS,Structural Parameter Register" bitfld.long 0x04 20.--23. " DEBUG_PORT_NUMBER ,The '0' indicating that the macro is not provided with debug ports is read" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x04 16. " P_INDICATOR ,Port Indicator" "Unsupported,Supported" textline " " bitfld.long 0x04 12.--15. " N_CC ,Number of Companion Controller" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x04 8.--11. " N_PCC ,Number of Ports per Companion Controller" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x04 7. " PRR ,Indicates the order in which the ports are routed" "Ascending,Depends on first N_PORTS" bitfld.long 0x04 4. " PPC ,Port Power Control" "Disabled,Enabled" textline " " bitfld.long 0x04 0.--3. " N_PORTS ,Number of accessible port registers in the operational register space" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "HCCPARAMS,Capability Parameter Register" hexmask.long.byte 0x08 8.--15. 1. " EECP ,EHCI Extended Capabilities Pointer" bitfld.long 0x08 4.--7. " IST ,Isochronous Scheduling Threshold" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x08 2. " ASPC ,Asynchronous Schedule Park Capability" "Unsupported,Supported" bitfld.long 0x08 1. " PFLF ,Programmable Frame List Flag" "Fixed to 1024,Frame list size in the USBCMD" textline " " bitfld.long 0x08 0. " AC64 ,Addressing Capability" "32 bits,64 bits" if (((per.l(ad:0x00810000+0x08))&0x06)==0x06) group.long 0x10++0x03 line.long 0x00 "USBCMD,USB Command Register" hexmask.long.byte 0x00 16.--23. 1. " ITC ,Interrupt Threshold Control" bitfld.long 0x00 11. " ASPME ,Asynchronous Schedule Park Mode Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 8.--9. " ASPMC ,Asynchronous Schedule Park Mode Count" ",1,2,3" bitfld.long 0x00 7. " LHCR ,Light Host Controller Reset" "Completed,Reset" textline " " bitfld.long 0x00 6. " IAAD ,Interrupt on Async Advance Doorbell" "No interrupt,Interrupt" bitfld.long 0x00 5. " ASE ,Asynchronous Schedule Enable" "Not processed,Processed" textline " " bitfld.long 0x00 4. " PSE ,Periodic Schedule Enable" "Not processed,Processed" bitfld.long 0x00 2.--3. " FLS ,Frame List Size" "1024 elements,512 elements,256 elements," textline " " bitfld.long 0x00 1. " HCRESET ,Host Controller Reset" "No reset,Reset" bitfld.long 0x00 0. " RS ,Run/Stop" "Stop,Run" elif (((per.l(ad:0x00810000+0x08))&0x06)==0x04) group.long 0x10++0x03 line.long 0x00 "USBCMD,USB Command Register" hexmask.long.byte 0x00 16.--23. 1. " ITC ,Interrupt Threshold Control" bitfld.long 0x00 11. " ASPME ,Asynchronous Schedule Park Mode Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 8.--9. " ASPMC ,Asynchronous Schedule Park Mode Count" ",1,2,3" bitfld.long 0x00 7. " LHCR ,Light Host Controller Reset" "Completed,Reset" textline " " bitfld.long 0x00 6. " IAAD ,Interrupt on Async Advance Doorbell" "No interrupt,Interrupt" bitfld.long 0x00 5. " ASE ,Asynchronous Schedule Enable" "Not processed,Processed" textline " " bitfld.long 0x00 4. " PSE ,Periodic Schedule Enable" "Not processed,Processed" textline " " bitfld.long 0x00 1. " HCRESET ,Host Controller Reset" "No reset,Reset" bitfld.long 0x00 0. " RS ,Run/Stop" "Stop,Run" elif (((per.l(ad:0x00810000+0x08))&0x06)==0x02) group.long 0x10++0x03 line.long 0x00 "USBCMD,USB Command Register" hexmask.long.byte 0x00 16.--23. 1. " ITC ,Interrupt Threshold Control" textline " " bitfld.long 0x00 7. " LHCR ,Light Host Controller Reset" "Completed,Reset" textline " " bitfld.long 0x00 6. " IAAD ,Interrupt on Async Advance Doorbell" "No interrupt,Interrupt" bitfld.long 0x00 5. " ASE ,Asynchronous Schedule Enable" "Not processed,Processed" textline " " bitfld.long 0x00 4. " PSE ,Periodic Schedule Enable" "Not processed,Processed" bitfld.long 0x00 2.--3. " FLS ,Frame List Size" "1024 elements,512 elements,256 elements," textline " " bitfld.long 0x00 1. " HCRESET ,Host Controller Reset" "No reset,Reset" bitfld.long 0x00 0. " RS ,Run/Stop" "Stop,Run" else group.long 0x10++0x03 line.long 0x00 "USBCMD,USB Command Register" hexmask.long.byte 0x00 16.--23. 1. " ITC ,Interrupt Threshold Control" textline " " bitfld.long 0x00 7. " LHCR ,Light Host Controller Reset" "Completed,Reset" textline " " bitfld.long 0x00 6. " IAAD ,Interrupt on Async Advance Doorbell" "No interrupt,Interrupt" bitfld.long 0x00 5. " ASE ,Asynchronous Schedule Enable" "Not processed,Processed" textline " " bitfld.long 0x00 4. " PSE ,Periodic Schedule Enable" "Not processed,Processed" textline " " bitfld.long 0x00 1. " HCRESET ,Host Controller Reset" "No reset,Reset" bitfld.long 0x00 0. " RS ,Run/Stop" "Stop,Run" endif group.long 0x14++0x17 line.long 0x00 "USBSTS,USB Status Register" rbitfld.long 0x00 15. " ASS ,Asynchronous Schedule Status" "Disabled,Enabled" rbitfld.long 0x00 14. " PSS ,Periodic Schedule Status" "Disabled,Enabled" textline " " rbitfld.long 0x00 13. " RECLAMATION ,Whether the Asynchronous Schedule is empty is indicated" "No,Yes" rbitfld.long 0x00 12. " HCHALTED ,Host controler process Run/Stop" "Stop,Run" textline " " eventfld.long 0x00 5. " IAA ,Interrupt on Async Advance" "No interrupt,Interrupt" eventfld.long 0x00 4. " HSE ,Host System Error" "No error,Error" textline " " eventfld.long 0x00 3. " FLR ,Frame List Rollover" "0,1" eventfld.long 0x00 2. " PCD ,Port Change Detect" "0,1" textline " " eventfld.long 0x00 1. " USBERRINT ,USB Error Interrupt" "No interrupt,Interrupt" eventfld.long 0x00 0. " USBINT ,USBINT" "Not completed,Completed" line.long 0x04 "USBINTR,USB Interrupt Enable Register" bitfld.long 0x04 5. " IAAE ,Interrupt on Async Advance Enable" "Disabled,Enabled" bitfld.long 0x04 4. " HSEE ,Host System Error Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 3. " FLRE ,Frame List Rollover Enable" "Disabled,Enabled" bitfld.long 0x04 2. " PCIE ,Port Change Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 1. " USBEIE ,USB Error Interrupt Enable" "Disabled,Enabled" bitfld.long 0x04 0. " USBIE ,USB Interrupt Enable" "Disabled,Enabled" line.long 0x08 "FRINDEX,USB Frame Index Register" hexmask.long.word 0x08 0.--13. 1. " FRAME_INDEX ,Value of the register is incremented at the end of each frame" line.long 0x0C "CTRLDSSEGMENT,4G Segment Selector Register" line.long 0x10 "PERIODICLISTBASE,Periodic Frame List Base Address Register" hexmask.long.tbyte 0x10 12.--31. 0x1000 " PERIODICLISTBASE ,Base address of Periodic Frame List in the memory area is set" line.long 0x14 "ASYNCLISTADDR,Asynchronous List Address Register" hexmask.long 0x14 5.--31. 0x20 " LINK_POINTER_LOW ,Queue head address of the Asynchronous Schedule to be executed next is stored" group.long 0x50++0x03 line.long 0x00 "CONFIGFLAG,Configured Flag Register" bitfld.long 0x00 0. " CF ,Configure flag" "OHCI,EHCI" if (((per.l(ad:0x00810000+0x04))&0x10010)==0x10010)&&(((per.l(ad:0x00810000+0x54))&0x04)==0x04) group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " bitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Off,On" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " SUSPEND ,Suspend" "Enabled,Suspended" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " PORT_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" elif (((per.l(ad:0x00810000+0x04))&0x10010)==0x10010)&&(((per.l(ad:0x00810000+0x54))&0x04)==0x00) group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " bitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Off,On" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " SUSPEND ,Suspend" "Disabled,Disabled" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " PORT_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" elif (((per.l(ad:0x00810000+0x04))&0x10010)==0x10)&&(((per.l(ad:0x00810000+0x54))&0x04)==0x04) group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " rbitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Off,On" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " SUSPEND ,Suspend" "Enabled,Suspended" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " PORT_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" elif (((per.l(ad:0x00810000+0x04))&0x10010)==0x10)&&(((per.l(ad:0x00810000+0x54))&0x04)==0x00) group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " rbitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Off,On" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " SUSPEND ,Suspend" "Disabled,Disabled" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " PORT_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" elif (((per.l(ad:0x00810000+0x04))&0x10010)==0x10000)&&(((per.l(ad:0x00810000+0x54))&0x04)==0x04) group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " bitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Unable,Unable" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " SUSPEND ,Suspend" "Enabled,Suspended" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " PORT_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" elif (((per.l(ad:0x00810000+0x04))&0x10010)==0x10000)&&(((per.l(ad:0x00810000+0x54))&0x04)==0x00) group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " bitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Unable,Unable" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " SUSPEND ,Suspend" "Disabled,Disabled" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " PORT_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" elif (((per.l(ad:0x00810000+0x04))&0x10010)==0x00)&&(((per.l(ad:0x00810000+0x54))&0x04)==0x04) group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " rbitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Unable,Unable" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " SUSPEND ,Suspend" "Enabled,Suspended" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " PORT_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" else group.long 0x54++0x03 line.long 0x00 "PORTSC_1,Port Status/Control Register 1" bitfld.long 0x00 22. " WKOC_E ,Wake on Over-current Enable" "Disabled,Enabled" bitfld.long 0x00 21. " WKDSCNNT_E ,Wake on Disconnect Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " WKCNNT_E ,Wake on Connect Enable" "Disabled,Enabled" bitfld.long 0x00 16.--19. " PTC ,This field specifies whether port mode should be test mode" "Not enable,Test J_STATE,Test K_STATE,Test SE0_NAK,Test packet,Test FORCE_ENABLE,,,,,,,,,," textline " " rbitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Off,Amber,Green,Undefined" bitfld.long 0x00 13. " POWER_OWNER ,Host Controller with port ownership is indicated" "EHCI Host,OHCI Host" textline " " bitfld.long 0x00 12. " PP ,Port power" "Unable,Unable" bitfld.long 0x00 10.--11. " LINE_STATUS ,State of USB port's signal wire is indicated" "SE0,J_STATE,K_STATE,Undefined" textline " " bitfld.long 0x00 8. " PR ,Port Reset" "Not Reset,Reset" bitfld.long 0x00 7. " SUSPEND ,Suspend" "Disabled,Disabled" textline " " bitfld.long 0x00 6. " FPR ,Force Port Resume" "No resume,Resume" eventfld.long 0x00 5. " OCC ,Over-current Change" "Not Active,Active" textline " " bitfld.long 0x00 4. " OCA ,Over-current Active" "Not over-current status,Over-current status" eventfld.long 0x00 3. " P(E/D)C ,Port Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " PORT_E/D ,Port Enable/Disable" "Disabled,Enabled" bitfld.long 0x00 1. " CSC ,Connect Status Change" "No change,Change" textline " " bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected,connected" endif group.long 0x90++0x0B line.long 0x00 "INSNREG00,Programmable Microframe Base Value Register" hexmask.long.word 0x00 1.--13. 1. " LMF ,The length of 1 micro frame is set" bitfld.long 0x00 0. " REGFCND/E ,This register function is enabled" "Disabled,Enabled" line.long 0x04 "INSNREG01,Programmable Packet Buffer OUT/IN Threshold Register" hexmask.long.word 0x04 16.--31. 1. " OUT_THRESHOLD ,Host Controller transfer to USB" hexmask.long.word 0x04 0.--15. 1. " IN_THRESHOLD ,Host Controller transfer to memory" line.long 0x08 "INSNREG02,Programmable Packet Buffer Depth Register" hexmask.word 0x08 0.--11. 1. " INSNREG02 ,Packet buffer depth is defined in DWORD unit" hgroup.long 0x9C++0x03 hide.long 0x00 "INSNREG03,Time-Available Offset Register" group.long 0xA0++0x03 line.long 0x00 "INSNREG04,Debug Register" bitfld.long 0x00 4. " NAK_EN ,NAK reload fix is controlled" "Enabled,Disabled" bitfld.long 0x00 2. " PORT_ENUM ,Measurement function at the port enumeration time" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " WRITE_CTRL_FAC ,Writing control function of HCCPARAMS" "Not possible,Possible" bitfld.long 0x00 0. " WRITE_CTRL_FUNC ,Writing control function of HCSPARAMS" "Not possible,Possible" tree.end base ad:0x00800200 tree "OHCI Operational Registers" width 20. rgroup.long 0x00++0x03 line.long 0x00 "HCREVISION,Revision Register" hexmask.long.byte 0x00 0.--7. 1. " REV ,Version of OHCI specification is indicated" group.long 0x04++0x1F line.long 0x00 "HCCONTROL,Control Register" bitfld.long 0x00 10. " RWE ,Remote Wake up Enable" "Disabled,Enabled" bitfld.long 0x00 9. " RWC ,Remote Wake up Connected" "No supported,Supported" textline " " bitfld.long 0x00 8. " IR ,Interrupt Routing" "INT,SMI" bitfld.long 0x00 6.--7. " HCFS ,Host Controller Functional State" "USB Reset,USB Resume,USB Operational,USB Suspend" textline " " bitfld.long 0x00 5. " BLE ,Bulk List Enable" "Disabled,Enabled" bitfld.long 0x00 4. " CLE ,Control List Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " IE ,Isochronous Enable" "Disabled,Enabled" bitfld.long 0x00 2. " PLE ,Periodic List Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0.--1. " CBSR ,Control Bulk Service Ratio" "1 Endpoint,2 Endpoint,3 Endpoint,4 Endpoint" line.long 0x04 "HCCOMMANDSTATUS,Command/Status Register" rbitfld.long 0x04 16.--17. " SOC ,Scheduling Overrun Count" "0,1,2,3" bitfld.long 0x04 3. " OCR ,Ownership Change Request" "Not set,Set" textline " " bitfld.long 0x04 2. " BLF ,Bulk List Filled" "Processed,Processing" bitfld.long 0x04 1. " CLF ,Control List Filled" "Processed,Processing" textline " " bitfld.long 0x04 0. " HCR ,Host Controller Reset" "No reset,Reset" line.long 0x08 "HCINTERRUPTSTATUS,Interrupt Status Register" bitfld.long 0x08 30. " OC ,Ownership Change" "Not set,Set" bitfld.long 0x08 6. " RHSC ,Root Hub Status Change" "Not changed,Changed" textline " " bitfld.long 0x08 5. " FNO ,Frame Number Overflow" "Not overflow,Overflow" bitfld.long 0x08 4. " UE ,Unrecoverable Error" "Not set,Set" textline " " bitfld.long 0x08 3. " RD ,Resume Detected" "Not detected,Detected" bitfld.long 0x08 2. " SF ,Startof Frame" "Not blocked,Blocked" textline " " bitfld.long 0x08 1. " WDH ,Write back Done Head" "Not completed,Completed" bitfld.long 0x08 0. " SO ,Scheduling Overrun" "Not detected,Detected" line.long 0x0C "HCINTERRUPTENABLE,Interrupt Enable Register" bitfld.long 0x0C 31. " MIE ,Master Interrupt Enable" "Disabled,Enabled" bitfld.long 0x0C 30. " OC ,Ownership Change Enable" "Disabled,Enabled" textline " " bitfld.long 0x0C 6. " RHSC ,Root Hub Status Change Enable" "Disabled,Enabled" bitfld.long 0x0C 5. " FNO ,Frame Number Overflow Enable" "Disabled,Enabled" textline " " bitfld.long 0x0C 4. " UE ,Unrecoverable Error Enable" "Disabled,Enabled" bitfld.long 0x0C 3. " RD ,Resume Detected Enable" "Disabled,Enabled" textline " " bitfld.long 0x0C 2. " SF ,Start Of Frame Enable" "Disabled,Enabled" bitfld.long 0x0C 1. " WDH ,Write back Done Head Enable" "Disabled,Enabled" textline " " bitfld.long 0x0C 0. " SO ,Scheduling Overrun Enable" "Disabled,Enabled" line.long 0x10 "HCINTERRUPTDISABLE,Interrupt Disable Register" bitfld.long 0x10 31. " MIE ,Master Interrupt Disable" "No,Yes" bitfld.long 0x10 30. " OC ,Ownership Change Disable" "No,Yes" textline " " bitfld.long 0x10 6. " RHSC ,Root Hub Status Change Disable" "No,Yes" bitfld.long 0x10 5. " FNO ,Frame Number Overflow Disable" "No,Yes" textline " " bitfld.long 0x10 4. " UE ,Unrecoverable Error Disable" "No,Yes" bitfld.long 0x10 3. " RD ,Resume Detected Disable" "No,Yes" textline " " bitfld.long 0x10 2. " SF ,Start Of Frame Disable" "No,Yes" bitfld.long 0x10 1. " WDH ,Write back Done Head Disable" "No,Yes" textline " " bitfld.long 0x10 0. " SO ,Scheduling Overrun Disable" "No,Yes" line.long 0x14 "HCHCCA,HCCA Register" hexmask.long.tbyte 0x14 8.--31. 1. " HCCA ,This is a pointer to the HCCA base address" line.long 0x18 "HCPERIODCURRENTED,Periodic Current ED Register" hexmask.long 0x18 4.--31. 0x10 " PCED ,This is a pointer to the current Periodic list ED" line.long 0x1C "HCCONTROLHEADED,Control Head ED Register" hexmask.long 0x1C 4.--31. 0x10 " CHED ,This is a pointer to the Control List Head ED" if (((per.l(ad:0x00810000+0x204))&0x10)==0x0) group.long 0x24++0x03 line.long 0x00 "HCCONTROLCURRENTED,Control Current ED Register" hexmask.long 0x00 4.--31. 0x10 " CCED ,This is a pointer to the current Control list ED" else rgroup.long 0x24++0x03 line.long 0x00 "HCCONTROLCURRENTED,Control Current ED Register" hexmask.long 0x00 4.--31. 0x10 " CCED ,This is a pointer to the current Control list ED" endif group.long 0x28++0x03 line.long 0x00 "HCBULKHEADED,Bulk Head ED Register" hexmask.long 0x00 4.--31. 0x10 " BHED ,This is a pointer to the Bulk List Head ED" if (((per.l(ad:0x00810000+0x204))&0x10)==0x0) group.long 0x2C++0x03 line.long 0x00 "HCBULKCURRENTED,Bulk Current ED Register" hexmask.long 0x00 4.--31. 0x10 " BCED ,This is a pointer to the current Bulk list ED" else rgroup.long 0x2C++0x03 line.long 0x00 "HCBULKCURRENTED,Bulk Current ED Register" hexmask.long 0x00 4.--31. 0x10 " BCED ,This is a pointer to the current Bulk list ED" endif group.long 0x30++0x03 line.long 0x00 "HCDONEHEAD,Done Head Register" hexmask.long 0x00 4.--31. 0x10 " DH ,This is a pointer to the Done Head ED" group.long 0x34++0x03 line.long 0x00 "HCFMINTERVAL,Frame Interval Register" bitfld.long 0x00 31. " FIT ,Frame Interval Toggle" "0,1" hexmask.long.word 0x00 16.--30. 1. " FSMPS ,FS Largest Data Packet" textline " " hexmask.long.word 0x00 0.--13. 1. " FI ,This field specifies the length of the frame" rgroup.long 0x38++0x07 line.long 0x00 "HCFMREMAINING,Frame Remaining Register" bitfld.long 0x00 31. " FRT ,Frame Remaining Toggle" "0,1" hexmask.long.word 0x00 0.--13. 1. " FR ,Frame Remaining" line.long 0x04 "HCFMNUMBER,Frame Number Register" hexmask.long.word 0x04 0.--15. 1. " FN ,Frame Number" group.long 0x40++0x07 line.long 0x00 "HCPERIODICSTART,Periodic Start Register" hexmask.long.word 0x00 0.--13. 1. " PS ,This field does the time setting that Host Controller starts the processing of Periodic list in the frame" line.long 0x04 "HCLSTHRESHOLD,LS Threshold Register" hexmask.long.word 0x04 0.--11. 1. " LST ,LS Threshold" if ((((per.l(ad:0x00810000+0x248))&0x1000)==0x00)&&(((per.l(ad:0x00810000+0x248))&0x200)==0x00)) group.long 0x48++0x03 line.long 0x00 "HCRHDESCRIPTORA,Root Hub Descriptor A Register" hexmask.long.byte 0x00 24.--31. 1. " POTPGT ,Power On To Power Good Time" bitfld.long 0x00 12. " NOCP ,No OverCurrent Protection" "Reported,Not reported" textline " " bitfld.long 0x00 11. " OCPM ,OverCurrent Protection Mode" "Global,Individual" bitfld.long 0x00 10. " DT ,Device Type" "0,1" textline " " bitfld.long 0x00 9. " NPS ,No Power Switching" "No,Yes" bitfld.long 0x00 8. " PSM ,Power Switching Mode" "Global,Individual" textline " " hexmask.long.byte 0x00 0.--7. 1. " NDP ,Number Downstream Ports" elif ((((per.l(ad:0x00810000+0x248))&0x1000)==0x1000)&&(((per.l(ad:0x00810000+0x248))&0x200)==0x00)) group.long 0x48++0x03 line.long 0x00 "HCRHDESCRIPTORA,Root Hub Descriptor A Register" hexmask.long.byte 0x00 24.--31. 1. " POTPGT ,Power On To Power Good Time" bitfld.long 0x00 12. " NOCP ,No OverCurrent Protection" "Reported,Not reported" textline " " bitfld.long 0x00 10. " DT ,Device Type" "0,1" textline " " bitfld.long 0x00 9. " NPS ,No Power Switching" "No,Yes" bitfld.long 0x00 8. " PSM ,Power Switching Mode" "Global,Individual" textline " " hexmask.long.byte 0x00 0.--7. 1. " NDP ,Number Downstream Ports" elif ((((per.l(ad:0x00810000+0x248))&0x1000)==0x00)&&(((per.l(ad:0x00810000+0x248))&0x200)==0x200)) group.long 0x48++0x03 line.long 0x00 "HCRHDESCRIPTORA,Root Hub Descriptor A Register" hexmask.long.byte 0x00 24.--31. 1. " POTPGT ,Power On To Power Good Time" bitfld.long 0x00 12. " NOCP ,No OverCurrent Protection" "Reported,Not reported" textline " " bitfld.long 0x00 11. " OCPM ,OverCurrent Protection Mode" "Global,Individual" bitfld.long 0x00 10. " DT ,Device Type" "0,1" textline " " bitfld.long 0x00 9. " NPS ,No Power Switching" "No,Yes" textline " " hexmask.long.byte 0x00 0.--7. 1. " NDP ,Number Downstream Ports" else group.long 0x48++0x03 line.long 0x00 "HCRHDESCRIPTORA,Root Hub Descriptor A Register" hexmask.long.byte 0x00 24.--31. 1. " POTPGT ,Power On To Power Good Time" bitfld.long 0x00 12. " NOCP ,No OverCurrent Protection" "Reported,Not reported" textline " " bitfld.long 0x00 10. " DT ,Device Type" "0,1" textline " " bitfld.long 0x00 9. " NPS ,No Power Switching" "No,Yes" textline " " hexmask.long.byte 0x00 0.--7. 1. " NDP ,Number Downstream Ports" endif if ((((per.l(ad:0x00810000+0x248))&0x200)==0x00)&&(((per.l(ad:0x00810000+0x248))&0x100)==0x100)) group.long 0x4C++0x03 line.long 0x00 "HCRHDESCRIPTORB,Root Hub Descriptor B Register" bitfld.long 0x00 18. " PPCM2 , Port Power Control Mask" "Influenced,Not influenced" bitfld.long 0x00 17. " PPCM1 , Port Power Control Mask" "Influenced,Not influenced" textline " " bitfld.long 0x00 2. " DR2 ,Device on Port 2 Removable" "Removable,Not removable" bitfld.long 0x00 1. " DR1 ,Device on Port 1 Removable" "Removable,Not removable" else group.long 0x4C++0x03 line.long 0x00 "HCRHDESCRIPTORB,Root Hub Descriptor B Register" bitfld.long 0x00 2. " DR2 ,Device on Port 2 Removable" "Removable,Not removable" bitfld.long 0x00 1. " DR1 ,Device on Port 1 Removable" "Removable,Not removable" endif if ((((per.l(ad:0x00810000+0x248))&0x1000)==0x00)&&(((per.l(ad:0x00810000+0x248))&0x800)==0x00)) group.long 0x50++0x03 line.long 0x00 "HCRHSTATUS,Root Hub Status Register" bitfld.long 0x00 17. " OCIC ,OverCurrent Indicator Change" "Disabled,Cleared" bitfld.long 0x00 16. " LPSC ,Local Power Status Change" "Not set,Set" textline " " setclrfld.long 0x00 15. 0x00 15. 0x00 31. " DRWE_SET/CLR ,Device Remote Wake up Enable" "Not set,set" rbitfld.long 0x00 1. " OCI ,OverCurrent Indicator" "Not detected,Detected" textline " " bitfld.long 0x00 0. " LPS ,Local Power Status" "Not cleared,Cleared" else group.long 0x50++0x03 line.long 0x00 "HCRHSTATUS,Root Hub Status Register" bitfld.long 0x00 17. " OCIC ,OverCurrent Indicator Change" "Disabled,Cleared" bitfld.long 0x00 16. " LPSC ,Local Power Status Change" "Not set,Set" textline " " setclrfld.long 0x00 15. 0x00 15. 0x00 31. " DRWE_SET/CLR ,Device Remote Wake up Enable" "Not set,set" textline " " bitfld.long 0x00 0. " LPS ,Local Power Status" "Not cleared,Cleared" endif textline " " if (((per.l(ad:0x00810000+0x254))&0x01)==0x01) if ((((per.l(ad:0x00810000+0x248))&0x800)==0x800)&&(((per.l(ad:0x00810000+0x248))&0x1000)==0x00)) group.long 0x54++0x03 line.long 0x00 "HCRHPORTSTATUS[1],Root Hub Port Status/Control Register 1" bitfld.long 0x00 20. " PRSC ,Port Reset Status Change R/W" "Not resumed/Disabled,Completed/Cleared" bitfld.long 0x00 19. " OCIC ,Port OverCurrent Indicator Change R/W" "Not resumed/Disabled,Ended/Cleared" textline " " bitfld.long 0x00 18. " PSSC ,Port Suspend Status Change R/W" "Not resumed/Disabled,Ended/Cleared" bitfld.long 0x00 17. " PESC ,Port Enable Status Change R/W" "Not Changed/Disabled,Changed/Cleared" textline " " bitfld.long 0x00 16. " CSC ,Connect Status Change R/W" "No connection/Disabled,Connection/Cleared" bitfld.long 0x00 9. " LSDA ,Low Speed Device Attached R/W" "Full/Disabled,Low/Cleared" textline " " bitfld.long 0x00 8. " PPS ,Port Power Status R/W" "Off/Disabled,On/Set" bitfld.long 0x00 4. " PRS ,Port Reset Status R/W" "Not active/Disabled,Active/Set" textline " " bitfld.long 0x00 3. " POCI ,Port OverCurrent Indicator R/W" "Normal current/Disabled,Over-current/Resume processing" bitfld.long 0x00 2. " PSS ,Port Suspend Status R/W" "Not suspended/Disabled,Suspended/Set" textline " " bitfld.long 0x00 1. " PES ,Port Enable Status R/W" "Disabled/Disabled,Enabled/Set" bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected/Disabled,Connected/Cleared" else group.long 0x54++0x03 line.long 0x00 "HCRHPORTSTATUS[1],Root Hub Port Status/Control Register 1" bitfld.long 0x00 20. " PRSC ,Port Reset Status Change R/W" "Not resumed/Disabled,Completed/Cleared" bitfld.long 0x00 19. " OCIC ,Port OverCurrent Indicator Change R/W" "Not resumed/Disabled,Ended/Cleared" textline " " bitfld.long 0x00 18. " PSSC ,Port Suspend Status Change R/W" "Not resumed/Disabled,Ended/Cleared" bitfld.long 0x00 17. " PESC ,Port Enable Status Change R/W" "Not Changed/Disabled,Changed/Cleared" textline " " bitfld.long 0x00 16. " CSC ,Connect Status Change R/W" "No connection/Disabled,Connection/Cleared" bitfld.long 0x00 9. " LSDA ,Low Speed Device Attached R/W" "Full/Disabled,Low/Cleared" textline " " bitfld.long 0x00 8. " PPS ,Port Power Status R/W" "Off/Disabled,On/Set" bitfld.long 0x00 4. " PRS ,Port Reset Status R/W" "Not active/Disabled,Active/Set" textline " " bitfld.long 0x00 2. " PSS ,Port Suspend Status R/W" "Not suspended/Disabled,Suspended/Set" textline " " bitfld.long 0x00 1. " PES ,Port Enable Status R/W" "Disabled/Disabled,Enabled/Set" bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected/Disabled,Connected/Cleared" endif else if ((((per.l(ad:0x00810000+0x248))&0x800)==0x800)&&(((per.l(ad:0x00810000+0x248))&0x1000)==0x00)) group.long 0x54++0x03 line.long 0x00 "HCRHPORTSTATUS[1],Root Hub Port Status/Control Register 1" bitfld.long 0x00 20. " PRSC ,Port Reset Status Change R/W" "Not resumed/Disabled,Completed/Cleared" bitfld.long 0x00 19. " OCIC ,Port OverCurrent Indicator Change R/W" "Not resumed/Disabled,Ended/Cleared" textline " " bitfld.long 0x00 18. " PSSC ,Port Suspend Status Change R/W" "Not resumed/Disabled,Ended/Cleared" bitfld.long 0x00 17. " PESC ,Port Enable Status Change R/W" "Not Changed/Disabled,Changed/Cleared" textline " " bitfld.long 0x00 16. " CSC ,Connect Status Change R/W" "No connection/Disabled,Connection/Cleared" textline " " bitfld.long 0x00 8. " PPS ,Port Power Status R/W" "Off/Disabled,On/Set" bitfld.long 0x00 4. " PRS ,Port Reset Status R/W" "Not active/Disabled,Active/Set" textline " " bitfld.long 0x00 3. " POCI ,Port OverCurrent Indicator R/W" "Normal current/Disabled,Over-current/Resume processing" bitfld.long 0x00 2. " PSS ,Port Suspend Status R/W" "Not suspended/Disabled,Suspended/Set" textline " " bitfld.long 0x00 1. " PES ,Port Enable Status R/W" "Disabled/Disabled,Enabled/Set" bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected/Disabled,Connected/Cleared" else group.long 0x54++0x03 line.long 0x00 "HCRHPORTSTATUS[1],Root Hub Port Status/Control Register 1" bitfld.long 0x00 20. " PRSC ,Port Reset Status Change R/W" "Not resumed/Disabled,Completed/Cleared" bitfld.long 0x00 19. " OCIC ,Port OverCurrent Indicator Change R/W" "Not resumed/Disabled,Ended/Cleared" textline " " bitfld.long 0x00 18. " PSSC ,Port Suspend Status Change R/W" "Not resumed/Disabled,Ended/Cleared" bitfld.long 0x00 17. " PESC ,Port Enable Status Change R/W" "Not Changed/Disabled,Changed/Cleared" textline " " bitfld.long 0x00 16. " CSC ,Connect Status Change R/W" "No connection/Disabled,Connection/Cleared" textline " " bitfld.long 0x00 8. " PPS ,Port Power Status R/W" "Off/Disabled,On/Set" bitfld.long 0x00 4. " PRS ,Port Reset Status R/W" "Not active/Disabled,Active/Set" textline " " bitfld.long 0x00 2. " PSS ,Port Suspend Status R/W" "Not suspended/Disabled,Suspended/Set" textline " " bitfld.long 0x00 1. " PES ,Port Enable Status R/W" "Disabled/Disabled,Enabled/Set" bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not connected/Disabled,Connected/Cleared" endif endif tree.end base ad:0x00812000 width 17. tree "Host Link Configuration Registers" group.long 0x00++0x0F line.long 0x00 "LINKMODESETTING,Link Mode Setting Register" hexmask.long.byte 0x00 24.--31. 1. " PHY_VSTATUS ,Vendor Status" bitfld.long 0x00 23. " SS_ULPI_PP2VBUS ,LINK mode setting" "0,1" textline " " bitfld.long 0x00 22. " SS_AUTOPPD_ON_OVERCUR_EN ,LINK mode setting" "0,1" textline " " bitfld.long 0x00 16.--21. " SS_FLADJ_VAL ,Frame Length Adjustment Register Per Port" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 10.--15. " SS_FLADJ_VAL_HOST ,The frame length is adjusted" "59488,59504,59520,59536,59552,59568,59584,59600,59616,59632,59648,59664,59680,59696,59712,59728,59744,59760,59776,59792,59808,59824,59840,59856,59872,59888,59904,59920,59936,59952,59968,59984,60000,60016,60032,60048,60064,60080,60096,60112,60128,60144,60160,60176,60192,60208,60224,60240,60256,60272,60288,60304,60320,60336,60352,60368,60384,60400,60416,60432,60448,60464,60480,60496" textline " " bitfld.long 0x00 9. " SS_SIMULATION_MODE ,Simulation mode signal" "Normal,Simulation" bitfld.long 0x00 8. " SS_WORLD_IF ,Word interface" "16 bit,8 bit" textline " " bitfld.long 0x00 7. " SS_NXT_POWER_STATE_VALID ,LINK mode setting" "0,1" bitfld.long 0x00 6. " SS_POWER_STATE_VALID ,LINK mode setting" "0,1" textline " " bitfld.long 0x00 4.--5. " SS_NEXT_POWER_STATE ,LINK mode setting" "0,1,2,3" bitfld.long 0x00 2.--3. " SS_POWER_STATE ,LINK mode setting" "0,1,2,3" textline " " bitfld.long 0x00 1. " SS_RESUME_UTMI_PLS_DIS ,Signal for debugging" "0,1" bitfld.long 0x00 0. " SS_UTMI_BACKWARD_ENB ,Signal for debugging" "0,1" line.long 0x04 "PHYModeSetting1,PHY Mode Setting 1 Register" bitfld.long 0x04 31. " RESET ,PHY block part reset signal" "No reset,Reset" bitfld.long 0x04 27. " SIM ,Input of simulation time reduction mode" "Normal,Reduced" textline " " bitfld.long 0x04 26. " ANPD ,PHY block analog circuit power-down signal" "Not set,Set" bitfld.long 0x04 25. " RPDMEN ,D- pull-down resistor on/off control signal" "Off,On" textline " " bitfld.long 0x04 24. " RPDPEN ,D+ pull-down resistor on/off control signal" "Off,On" bitfld.long 0x04 23. " ENVDETSEL1 ,PHY mode setting" "0,1" textline " " bitfld.long 0x04 22. " ENVDETSEL0 ,PHY mode setting" "0,1" bitfld.long 0x04 21. " HSDTRSELS ,PHY mode setting" "0,1" textline " " bitfld.long 0x04 20. " HSDTRSELF ,PHY mode setting" "0,1" bitfld.long 0x04 19. " CRYCNTENX ,PHY mode setting" "0,1" textline " " bitfld.long 0x04 18. " CLKSEL1 ,PHY mode setting" "0,1" bitfld.long 0x04 17. " CLKSEL0 ,PHY mode setting" "0,1" textline " " bitfld.long 0x04 16. " PSWENX ,PHY mode setting" "0,1" bitfld.long 0x04 14. " EOP_TIMER_EN ,PHY mode setting" "0,1" textline " " bitfld.long 0x04 9. " CONTCDR ,PHY mode setting" "0,1" bitfld.long 0x04 4. " ENFLTR ,PHY mode setting" "0,1" textline " " bitfld.long 0x04 3. " RPUENXEN ,PHY mode setting" "0,1" bitfld.long 0x04 2. " RPUEN2 ,PHY mode setting" "0,1" textline " " bitfld.long 0x04 0. " Dbus16 ,PHY mode setting" "0,1" line.long 0x08 "PHYModeSetting2,PHY Mode Setting 2 Register" rbitfld.long 0x08 30. " COMPMEASREG3 ,COMPMEASREG3" "0,1" rbitfld.long 0x08 29. " COMPMEASREG2 ,COMPMEASREG2" "0,1" textline " " rbitfld.long 0x08 28. " COMPMEASREG1 ,COMPMEASREG1" "0,1" bitfld.long 0x08 26. " COMPTEST3 ,PHY mode setting" "0,1" textline " " bitfld.long 0x08 25. " COMPTEST2 ,PHY mode setting" "0,1" bitfld.long 0x08 24. " COMPTEST1 ,PHY mode setting" "0,1" textline " " bitfld.long 0x08 23. " COMPTESTSEL ,PHY mode setting" "0,1" bitfld.long 0x08 21. " EARLYSYNC ,PHY mode setting" "0,1" textline " " bitfld.long 0x08 20. " REFLMASK ,PHY mode setting" "0,1" bitfld.long 0x08 19. " HSDSEL1 ,PHY mode setting" "0,1" textline " " bitfld.long 0x08 18. " HSDSEL0 ,PHY mode setting" "0,1" bitfld.long 0x08 17. " SQSEL ,PHY mode setting" "0,1" textline " " hexmask.long.byte 0x08 8.--14. 1. " COMPDISCON ,PHY mode setting" bitfld.long 0x08 7. " COMPUPDPLS ,PHY mode setting" "0,1" textline " " bitfld.long 0x08 5. " COMPUPDCTL3 ,PHY mode setting" "0,1" bitfld.long 0x08 4. " COMPUPDCTL2 ,PHY mode setting" "0,1" textline " " bitfld.long 0x08 3. " COMPUPDCTL1 ,PHY mode setting" "0,1" bitfld.long 0x08 0.--2. " LEOP ,PHY mode setting" "0,1,2,3,4,5,6,7" line.long 0x0C "CONFIG setting,CONFIG setting Register" bitfld.long 0x0C 0.--2. " CONF ,CONFIG setting" "0,1,2,3,4,5,6,7" tree.end base ad:0x00814000 width 14. tree "Function Link Registers" group.long 0x00++0x0F line.long 0x00 "CPAC,USB Function CPU Access Control Register" bitfld.long 0x00 16. " CONFIGWREN ,Write access to make-up area is controlled" "Invalidated,Validated" bitfld.long 0x00 3. " SOFTRESET ,Reset of USB function unit is performed status" "Not preformed,Preformed" textline " " bitfld.long 0x00 2. " CPUBYTEODER ,Byte ordering is specified when CPU and DMAC access to the register" "Little endian,Big endian" bitfld.long 0x00 0.--1. " CPUBUSWIDTH ,The width of the data bus in CPU interface is set" ",,32,32" line.long 0x04 "DVC,USB Function Device Control Register" bitfld.long 0x04 31. " MSKERRATICERR ,Mask bit of ErraticErr interrupt" "Not masked,Masked" bitfld.long 0x04 30. " MSKSETCONF ,Mask bit of SetConfigure interrupt" "Not masked,Masked" textline " " bitfld.long 0x04 29. " MSKUSBRSTB ,Mask bit of USB reset start interrupt" "Not masked,Masked" bitfld.long 0x04 28. " MSKUSBRSTE ,Mask bit of USB reset end interrupt" "Not masked,Masked" textline " " bitfld.long 0x04 27. " MSKSETUP ,Mask bit of setup interrupt" "Not masked,Masked" bitfld.long 0x04 26. " MSKSOF ,Mask bit of SOF interrupt" "Not masked,Masked" textline " " bitfld.long 0x04 25. " MSKSUSPENDB ,Mask bit of suspend start interrupt" "Not masked,Masked" bitfld.long 0x04 24. " MSKSUSPENDE ,Mask bit of suspend end interrupt" "Not masked,Masked" textline " " bitfld.long 0x04 19. " L_MODE ,This is for test. Set the value to 0H" "PHY block + LINK block,LINK single purpose mode" bitfld.long 0x04 18. " P_MODE ,PHY block single purpose mode is set" "PHY block + LINK block,LINK single purpose mode" textline " " bitfld.long 0x04 17. " LPBKPHY ,Setting PHY to loopback test mode is specified" "Not done,Tested" bitfld.long 0x04 14. " PHYSUSP ,Setting PHY forcibly to suspend mode is specified" "Operation mode,SUSPEND mode" textline " " bitfld.long 0x04 5. " DISCONNECT ,Whether to output 'non-driving' state to PHY is specified" "Normal operation,Loopback test mode" bitfld.long 0x04 4. " SELFPOWER ,Power supply of the device is set" "Buf power,Self power" textline " " bitfld.long 0x04 3. " ENRMTWKUP ,Remote wake-up function is controlled" "Disabled,Enabled" bitfld.long 0x04 2. " REQRESUME ,Resume request output is specified" "Not output,Output" textline " " bitfld.long 0x04 0.--1. " REQSPEED ,PHY type is specified for connection" "HighSpeed,FullSpeed,," line.long 0x08 "DVS,Device Status Register" bitfld.long 0x08 31. " INTERRATICERR ,Whether PHY is hung up is indicated" "No,Yes" bitfld.long 0x08 30. " INTSETCONF ,Whether Configuration value is set by SetConfiguration is indicated" "Not performed,Performed" textline " " bitfld.long 0x08 29. " INTUSBRSTB ,It is an interrupt factor by having detected BUS RESET beginning on USB" "Not interrupt,Interrupt" bitfld.long 0x08 28. " INTUSBRSTE ,It is an interrupt factor by having detected BUS RESET ending on USB" "Not interrupt,Interrupt" textline " " bitfld.long 0x08 27. " INTSETUP ,It is an interrupt factor that detects beginning the Setup stage and depends especially" "Not interrupt,Interrupt" bitfld.long 0x08 26. " INTSOF ,It is an interrupt factor by having detected the reception of Sof" "Not interrupt,Interrupt" textline " " bitfld.long 0x08 25. " INTSUSPENDB ,It is an interrupt factor by having detected the state of Suspend with USB" "Not interrupt,Interrupt" bitfld.long 0x08 24. " INTSUSPENDE ,The state of Suspend ended by USB and the interrupt factor" "Not interrupt,Interrupt" textline " " rbitfld.long 0x08 20.--23. " CONF ,Current Configuration value is indicated" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" rbitfld.long 0x08 16.--17. " CRTSPEED ,USB connection speed is indicated" "HighSpeed mode,FullSpeed mode,," textline " " rbitfld.long 0x08 15. " PHYRESET ,This is status bit indicating interface between PYH - LINK" "Released and the operation starts,Reset-not started" rbitfld.long 0x08 9. " BUSRESET ,This is status bit indicating USB reset operation status" "Not reset,Reset" textline " " rbitfld.long 0x08 8. " SUSPEND ,This is status bit indicating whether device is in suspended" "No,Yes" line.long 0x0C "EPIC,USB Function Endpoint Interrupt Control Register" bitfld.long 0x0C 3. " MSKEP3 ,This is mask bit to the interrupt notified from endpoint3" "Not masked,Masked" bitfld.long 0x0C 2. " MSKEP2 ,This is mask bit to the interrupt notified from endpoint2" "Not masked,Masked" textline " " bitfld.long 0x0C 1. " MSKEP1 ,This is mask bit to the interrupt notified from endpoint1" "Not masked,Masked" bitfld.long 0x0C 0. " MSKEP0 ,This is mask bit to the interrupt notified from endpoint0" "Not masked,Masked" rgroup.long 0x10++0x03 line.long 0x00 "EPIS,USB Function Endpoint Interrupt Status Register" bitfld.long 0x00 3. " INTEP3 ,Whether notifying interrupt from endpoint3 is indicated" "Not notified,Notified" bitfld.long 0x00 2. " INTEP2 ,Whether notifying interrupt from endpoint2 is indicated" "Not notified,Notified" textline " " bitfld.long 0x00 1. " INTEP1 ,Whether notifying interrupt from endpoint1 is indicated" "Not notified,Notified" bitfld.long 0x00 0. " INTEP0 ,Whether notifying interrupt from endpoint0 is indicated" "Not notified,Notified" group.long 0x14++0x03 line.long 0x00 "EPDC,USB Function Endpoint DMA Control Register" bitfld.long 0x00 18. " DMAMODE2 ,Utilization of DMA transfer at endpoint2 is indicated" "Not used,Used" bitfld.long 0x00 17. " DMAMODE1 ,Utilization of DMA transfer at endpoint1 is indicated" "Not used,Used" textline " " bitfld.long 0x00 2. " MSKDMAREQ2 ,Whether to mask DMA transfer request from endpoint2 is specified" "Not masked,Masked" bitfld.long 0x00 1. " MSKDMAREQ1 ,Whether to mask DMA transfer request from endpoint1 is specified" "Not masked,Masked" rgroup.long 0x18++0x07 line.long 0x00 "EPDS,USB Function Endpoint DMA Status Register" bitfld.long 0x00 2. " DMAREQ2 ,DMA transfer request from endpoint2 is indicated" "Not requested,Requested" bitfld.long 0x00 1. " DMAREQ2 ,DMA transfer request from endpoint2 is indicated" "Not requested,Requested" line.long 0x04 "TSTAMP,Function Time Stamp Register" hexmask.long.word 0x04 0.--10. 1. " TIMSTAMP ,Frame number at SOF reception is indicated" group.long 0x20++0x03 line.long 0x00 "EPTCSEL,UFEpTCSel Register" bitfld.long 0x00 2. " TCSELUSB2 ,Total transfer count value is specified at reading EpTC2" "CPU,USB" bitfld.long 0x00 1. " TCSELUSB1 ,Total transfer count value is specified at reading EpTC1" "CPU,USB" group.long 0x24++0x07 line.long 0x00 "EPTC1,USB Function Endpoint1 Terminal Count Register" line.long 0x04 "EPTC2,USB Function Endpoint2 Terminal Count Register" rgroup.long 0x70++0x03 line.long 0x00 "EPRS0,USB Function Endpoint0 Rx Size Register" bitfld.long 0x00 15. " SELTX0I ,Function of Size0i bit is selected" "RxSize0i,TxSize0i" hexmask.long.byte 0x00 8.--14. 1. " SIZE0I ,Number of transmission data byte written in EndPoint0i is displayed" textline " " bitfld.long 0x00 7. " SELTX0O ,RxSize0o or TxSize0o is selected as a function of the EpRS0 register of six bits-0 bits" "RxSize0o,TxSize0o" hexmask.long.byte 0x00 0.--6. 1. " SIZE0O ,Number of reception data byte written in/read from EndPoint0o is displayed" rgroup.long 0x78++0x03 line.long 0x00 "EPRS1,USB Function Endpoint1 Rx Size Register" bitfld.long 0x00 15. " SELTX1 ,Function of Size1 bit is selected" "RxSize1,TxSize1" hexmask.long.word 0x00 0.--10. 1. " SIZE1 ,Setting to OUT/IN transfer buffer with T/RxSize1" rgroup.long 0x80++0x03 line.long 0x00 "EPRS2,USB Function Endpoint2 Rx Size Register" bitfld.long 0x00 15. " SELTX2 ,Function of Size2 bit is selected" "RxSize2,TxSize2" hexmask.long.word 0x00 0.--10. 1. " SIZE2 ,Setting to OUT/IN transfer buffer with T/RxSize2" group.long 0x88++0x03 line.long 0x00 "EPRS3,USB Function Endpoint3 Rx Size Register" bitfld.long 0x00 15. " SELTX3 ,Function of Size3 bit is selected" "RxSize3,TxSize3" hexmask.long.word 0x00 0.--10. 1. " SIZE3 ,Setting to OUT/IN transfer buffer with T/RxSize3" group.long 0xF0++0x0F line.long 0x00 "CUSCNT,UFCusCnt Register" hexmask.long.byte 0x00 24.--31. 0x1000000 " TADD ,The Address value set to Device" bitfld.long 0x00 21. " TESTSE0NACK ,TESTSe0Nack" "Normal operation,TEST mode" textline " " bitfld.long 0x00 20. " TESTK ,TESTK" "Normal operation,TEST mode" bitfld.long 0x00 19. " TESTJ ,TESTJ" "Normal operation,TEST mode" textline " " bitfld.long 0x00 18. " TESTP ,TESTP" "Normal operation,TEST mode" bitfld.long 0x00 17. " SETCONFIG ,SetConfig" "Normal operation,Device is set to ADDRESSED" textline " " bitfld.long 0x00 16. " SETADD ,The state of Device State" "Normal operation,Device is set to ADDRESSED" bitfld.long 0x00 8. " ENINIFIFO ,The function of EpC0 register IniFifo0i IniFifo0o and EpC* register IniFifo* invalidated/valid" "Invalid,Valid" textline " " bitfld.long 0x00 2. " RPUON ,ExtRPU output" "0,1" bitfld.long 0x00 1. " CNTRPU ,The macro of the control of On/Off of the Pull-Up resistance" "Of,On" textline " " bitfld.long 0x00 0. " EXTRPU ,Whether to use pull-up resistance of built-in LSI is set" "Used,Not used" line.long 0x04 "CALB,UFCALB Register" bitfld.long 0x04 4.--6. " HSCALIB ,Timeout adjustment bit of HS protocol" "0,1,2,3,4,5,6,7" bitfld.long 0x04 0.--2. " FSCALIB ,Timeout adjustment bit of FS protocol" "0,1,2,3,4,5,6,7" line.long 0x08 "EPLPBK,UFEpLpBk Register" bitfld.long 0x08 4.--7. " EPLPBKO0 ,Endpoint on LoopBack0 OUT is set" "Not tested,EndPoint1 setting,EndPoint2 setting,,,,,,,,,,,,," bitfld.long 0x08 0.--3. " EPLPBKI0 ,EndPoint on LoopBack0 IN is set" "Not tested,EndPoint1 setting,EndPoint2 setting,EndPoint3 setting,,,,,,,,,,,," line.long 0x0C "INTFALTNUM,UFIntfAltNum Register" bitfld.long 0x0C 16.--18. " NUMINTF ,The number of InterFace use in the EndPoint composition used is set" ",Intf0 only used,Intf0 1 is used,Intf0 1 2 is used,Everything,,," bitfld.long 0x0C 12.--14. " NUMALTINTF3 ,The number of InterFace3 of Alternate use is set by the EndPoint composition used" "InterFace3 is not used,Alternate0 only used,Alternate0 1 is used,Alternate0 1 2 is used,Everything,,," textline " " bitfld.long 0x0C 8.--10. " NUMALTINTF2 ,The number of InterFace2 of Alternate use is set by the EndPoint composition used" "InterFace2 is not used,Alternate0 only used,Alternate0 1 is used,Alternate0 1 2 is used,Everything,,," bitfld.long 0x0C 4.--6. " NUMALTINTF1 ,The number of InterFace1 of Alternate use is set by the EndPoint composition used" "InterFace1 is not used,Alternate0 only used,Alternate0 1 is used,Alternate0 1 2 is used,Everything,,," textline " " bitfld.long 0x0C 0.--2. " NUMALTINTF0 ,The number of InterFace0 of Alternate use is set by the EndPoint composition used" "InterFace0 is not used,Alternate0 only used,Alternate0 1 is used,Alternate0 1 2 is used,Everything,,," group.long 0x100++0x03 line.long 0x00 "EpC0,USB Function Endpoint0 Control Register" bitfld.long 0x00 23. " MSKCLSTALL ,This is mask bit to IntClStall interrupt" "Not masked,Masked" bitfld.long 0x00 22. " MSKNACK ,This is mask bit to IntNack interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 21. " MSKSTALLED ,This is mask bit to IntStalled interrupt" "Not masked,Masked" bitfld.long 0x00 18. " MSKPING0O ,This is mask bit to IntPing0o interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 17. " MSKREADY0O ,This is mask bit to IntReady0o interrupt" "Not masked,Masked" bitfld.long 0x00 16. " MSKREADY0I ,This is mask bit to IntReady0i interrupt" "Not masked,Masked" textline " " eventfld.long 0x00 15. " INIFIFO0O ,FIFO surroundings of endpoint0o are initialized" "Not performed,Performed" eventfld.long 0x00 14. " INIFIFO0I ,FIFO surroundings of endpoint0o are initialized" "Not performed,Performed" textline " " bitfld.long 0x00 7. " TESTMODE0 ,Loopback test mode of endpoint0 is set" "Normal operation,Loopback test mode" bitfld.long 0x00 2. " REQSTALL ,Generation control bit of Stall when forwarding it to EndPoint0" "Not returned,Returned" textline " " eventfld.long 0x00 1. " INIT0O ,Initialization of OUT transfer buffer at endpoint0 is instructed" "Not initialized,Initialized" eventfld.long 0x00 0. " INIT0I ,Initialization of IN transfer buffer at endpoint0 is instructed" "Not initialized,Initialized" rgroup.long 0x104++0x3 line.long 0x00 "EPS0,USB Function Endpoint0 Status Register" bitfld.long 0x00 23. " INTCLSTALL ,It is an interrupt factor to show that Stall was released" "No,Yes" bitfld.long 0x00 22. " INTNACK ,It is an interrupt factor to show the state of Nack without the distinction of OUT IN forwarding" "No,Yes" textline " " bitfld.long 0x00 21. " INTSTALLED ,It is an interrupt factor to show the state of Stall" "No,Yes" bitfld.long 0x00 18. " INTPING0O ,It is an interrupt factor to show that Ping has been sent to EndPoint 0" "Not requested,Requested" textline " " bitfld.long 0x00 17. " INTREADY0O ,It is an interrupt factor to show that the OUT data transfer to End Point 0 ended normally" "Not requested,Requested" bitfld.long 0x00 16. " INTREADY0I ,IntReady0i interrupt request is indicated" "Not requested,Requested" textline " " bitfld.long 0x00 4. " READY0O ,Data reading end instruction bit for EndPoint0 out forwarding at Write" "Not ended,Ends" bitfld.long 0x00 3. " READY0I ,Whether endpoint0i buffer is busy is indicated" "Not ended,Ends" textline " " bitfld.long 0x00 2. " STALLED ,Whether the state is Stall is indicated" "Not stall,Stall" group.long 0x108++0x03 line.long 0x00 "EPC1,USB Function Endpoint1 Control Register" bitfld.long 0x00 24.--27. " TESTALT1 ,This field is to directly set alternate value for testing" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 23. " MSKCLSTALL1 ,This is mask bit to IntClStall1 interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 22. " MSKNACK1 ,This is mask bit to IntNack1 interrupt" "Not masked,Masked" bitfld.long 0x00 21. " MSKSTALLED1 ,This is mask bit to IntStalled1 interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 20. " MSKEMPTY1 ,This is mask bit to IntEmpty1 interrupt" "Not masked,Masked" bitfld.long 0x00 19. " MSKDEND1 ,This is mask bit to IntDEnd1 interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 18. " MSKACHG1 ,This is mask bit to IntAChg1 interrupt" "Not masked,Masked" bitfld.long 0x00 17. " MSKPING1 ,This is mask bit to IntPing1 interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 16. " MSKREADY1 ,This is mask bit to IntReady1 interrupt" "Not masked,Masked" eventfld.long 0x00 15. " INIFIFO1 ,FIFO surroundings of endpoint1 are initialized" "Not performed,Performed" textline " " bitfld.long 0x00 14. " MSKSPDD1 ,This is mask bit to IntSPDD interrupt" "Not masked,Masked" bitfld.long 0x00 13. " MSKSPR1 ,This is mask bit to IntSPR interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 11. " ENSPDD1 ,Short packet DMA Done mode is set" "No,Yes" bitfld.long 0x00 10. " ENSPR1 ,The Short Packet Receive mode is set" "No,Yes" textline " " bitfld.long 0x00 9. " NACKRESP1 ,Nac response is instructed to bulk IN/OUT transfer" "Normal response,Nac response" bitfld.long 0x00 8. " NULLRESP1 ,It is a bit that demands an effective Null response for BULK IN/INTERRUPT IN" "Normal response,Null response" textline " " bitfld.long 0x00 7. " TESTMODE1 ,Test mode setting to endpoint1 is specified" "Normal response,Test mode" bitfld.long 0x00 6. " STALLDIS1 ,Stall initialization automatically is specified" "Automatically initialized,Not automatically initialized" textline " " bitfld.long 0x00 5. " TOGGLEDIS1 ,Toggle initialization automatically is specified" "Automatically initialized,Not automatically initialized" eventfld.long 0x00 4. " INISTALL1 ,This field is to instruct Stall initialization of endpoint1" "Not initialized,Initialized" textline " " eventfld.long 0x00 3. " INITOGGLE1 ,Initialization bit of Toggle of EndPoint1" "Not initialized,Initialized" bitfld.long 0x00 1. " REQSTALL1 ,Generation control bit of Stall when forwarding it to EndPoint" "Not returned,Returned" textline " " eventfld.long 0x00 0. " INIT1 ,This field is to instruct buffer initialization of endpoint1" "Not initialized,Initialized" group.long 0x10C++0x03 line.long 0x00 "EPS1,USB Function Endpoint1 Status Register" rbitfld.long 0x00 28.--31. " CRTINTF1 ,Interface value of endpoint1 is indicated" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" rbitfld.long 0x00 24.--27. " CRTALT1 ,Alternate value of endpoint1 is indicated" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 23. " INTCLSTALL1 ,It is an interrupt factor to show that Stall was released" "No interrupt,Interrupt" bitfld.long 0x00 22. " INTNACK1 ,IntNack1 interrupt request is indicated" "Not requested,Requested" textline " " bitfld.long 0x00 21. " INTSTALLED1 ,IntStalled1 interrupt request is indicated" "Not requested,Requested" bitfld.long 0x00 20. " INTEMPTY1 ,IntEmpty1 interrupt request is indicated" "Not requested,Requested" textline " " bitfld.long 0x00 19. " INTDEND1 ,IntDEnd1 interrupt request is indicated" "Not requested,Requested" bitfld.long 0x00 18. " INTACHG1 ,IntAChg1 interrupt request is indicated" "Not requested,Requested" textline " " bitfld.long 0x00 17. " INTPING1 ,IntPing1 interrupt request is indicated" "Not requested,Requested" bitfld.long 0x00 16. " INTREADY1 ,IntReady1 interrupt request is indicated" "Not possible,Possible" textline " " bitfld.long 0x00 14. " INTSPDD1 ,IntSPDD1 interrupt request is indicated" "No interrupt,Interrupt" bitfld.long 0x00 13. " INTSPR1 ,IntSPR1 interrupt request is indicated" "No interrupt,Interrupt" textline " " rbitfld.long 0x00 12. " EMPTY1 ,Whether endpoint1 buffer is empty is indicated" "Not empty,Empty" eventfld.long 0x00 3. " READY1O ,Data reading end instruction bit for EndPoint1 forwarding at Write" "No,Yes" textline " " eventfld.long 0x00 2. " READY1I ,Data writing end instruction bit for EndPoint1 forwarding at Write" "No,Yes" rbitfld.long 0x00 1. " STALLED1 ,Whether the state of endpoint1 is stall is indicated" "Not Stall,Stall" group.long 0x110++0x03 line.long 0x00 "EPC2,USB Function Endpoint2 Control Register" bitfld.long 0x00 24.--27. " TESTALT2 ,This field is to directly set alternate value for testing" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 23. " MSKCLSTALL2 ,This is mask bit to IntClStall2 interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 22. " MSKNACK2 ,This is mask bit to IntNack2 interrupt" "Not masked,Masked" bitfld.long 0x00 21. " MSKSTALLED2 ,This is mask bit to IntStalled2 interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 20. " MSKEMPTY2 ,This is mask bit to IntEmpty2 interrupt" "Not masked,Masked" bitfld.long 0x00 19. " MSKDEND2 ,This is mask bit to IntDEnd2 interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 18. " MSKACHG2 ,This is mask bit to IntAChg2 interrupt" "Not masked,Masked" bitfld.long 0x00 17. " MSKPING2 ,This is mask bit to IntPing2 interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 16. " MSKREADY2 ,This is mask bit to IntReady2 interrupt" "Not masked,Masked" eventfld.long 0x00 15. " INIFIFO2 ,FIFO surroundings of endpoint2 are initialized" "Not performed,Performed" textline " " bitfld.long 0x00 14. " MSKSPDD2 ,This is mask bit to IntSPDD interrupt" "Not masked,Masked" bitfld.long 0x00 13. " MSKSPR2 ,This is mask bit to IntSPR interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 11. " ENSPDD2 ,Short packet DMA Done mode is set" "No,Yes" bitfld.long 0x00 10. " ENSPR2 ,The Short Packet Receive mode is set" "No,Yes" textline " " bitfld.long 0x00 9. " NACKRESP2 ,Nac response is instructed to bulk IN/OUT transfer" "Normal response,Nac response" bitfld.long 0x00 8. " NULLRESP2 ,It is a bit that demands an effective Null response for BULK IN/INTERRUPT IN" "Normal response,Null response" textline " " bitfld.long 0x00 7. " TESTMODE2 ,Test mode setting to endpoint2 is specified" "Normal response,Test mode" bitfld.long 0x00 6. " STALLDIS2 ,Stall initialization automatically is specified" "Automatically initialized,Not automatically initialized" textline " " bitfld.long 0x00 5. " TOGGLEDIS2 ,Toggle initialization automatically is specified" "Automatically initialized,Not automatically initialized" eventfld.long 0x00 4. " INISTALL2 ,This field is to instruct Stall initialization of endpoint2" "Not initialized,Initialized" textline " " eventfld.long 0x00 3. " INITOGGLE2 ,Initialization bit of Toggle of EndPoint2" "Not initialized,Initialized" bitfld.long 0x00 1. " REQSTALL2 ,Generation control bit of Stall when forwarding it to EndPoint" "Not returned,Returned" textline " " eventfld.long 0x00 0. " INIT2 ,This field is to instruct buffer initialization of endpoint2" "Not initialized,Initialized" group.long 0x114++0x03 line.long 0x00 "EPS2,USB Function Endpoint2 Status Register" rbitfld.long 0x00 28.--31. " CRTINTF2 ,Interface value of endpoint2 is indicated" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" rbitfld.long 0x00 24.--27. " CRTALT2 ,Alternate value of endpoint2 is indicated" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 23. " INTCLSTALL2 ,It is an interrupt factor to show that Stall was released" "No interrupt,Interrupt" bitfld.long 0x00 22. " INTNACK2 ,IntNack2 interrupt request is indicated" "Not requested,Requested" textline " " bitfld.long 0x00 21. " INTSTALLED2 ,IntStalled2 interrupt request is indicated" "Not requested,Requested" bitfld.long 0x00 20. " INTEMPTY2 ,IntEmpty2 interrupt request is indicated" "Not requested,Requested" textline " " bitfld.long 0x00 19. " INTDEND2 ,IntDEnd2 interrupt request is indicated" "Not requested,Requested" bitfld.long 0x00 18. " INTACHG2 ,IntAChg2 interrupt request is indicated" "Not requested,Requested" textline " " bitfld.long 0x00 17. " INTPING2 ,IntPing2 interrupt request is indicated" "Not requested,Requested" bitfld.long 0x00 16. " INTREADY2 ,IntReady2 interrupt request is indicated" "Not possible,Possible" textline " " bitfld.long 0x00 14. " INTSPDD2 ,IntSPDD2 interrupt request is indicated" "No interrupt,Interrupt" bitfld.long 0x00 13. " INTSPR2 ,IntSPR2 interrupt request is indicated" "No interrupt,Interrupt" textline " " rbitfld.long 0x00 12. " EMPTY2 ,Whether endpoint2 buffer is empty is indicated" "Not empty,Empty" eventfld.long 0x00 3. " READY2O ,Data reading end instruction bit for EndPoint2 forwarding at Write" "No,Yes" textline " " eventfld.long 0x00 2. " READY2I ,Data writing end instruction bit for EndPoint2 forwarding at Write" "No,Yes" rbitfld.long 0x00 1. " STALLED2 ,Whether the state of endpoint2 is stall is indicated" "Not Stall,Stall" group.long 0x118++0x03 line.long 0x00 "EPC3,USB Function Endpoint3 Control Register" bitfld.long 0x00 24.--27. " TESTALT3 ,This field is to directly set alternate value for testing" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 23. " MSKCLSTALL3 ,This is mask bit to IntClStall3 interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 22. " MSKNACK3 ,This is mask bit to IntNack3 interrupt" "Not masked,Masked" bitfld.long 0x00 21. " MSKSTALLED3 ,This is mask bit to IntStalled3 interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 20. " MSKEMPTY3 ,This is mask bit to IntEmpty3 interrupt" "Not masked,Masked" bitfld.long 0x00 19. " MSKDEND3 ,This is mask bit to IntDEnd3 interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 18. " MSKACHG3 ,This is mask bit to IntAChg3 interrupt" "Not masked,Masked" bitfld.long 0x00 17. " MSKPING3 ,This is mask bit to IntPing3 interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 16. " MSKREADY3 ,This is mask bit to IntReady3 interrupt" "Not masked,Masked" eventfld.long 0x00 15. " INIFIFO3 ,FIFO surroundings of endpoint3 are initialized" "Not performed,Performed" textline " " bitfld.long 0x00 14. " MSKSPDD3 ,This is mask bit to IntSPDD interrupt" "Not masked,Masked" bitfld.long 0x00 13. " MSKSPR3 ,This is mask bit to IntSPR interrupt" "Not masked,Masked" textline " " bitfld.long 0x00 11. " ENSPDD3 ,Short packet DMA Done mode is set" "No,Yes" bitfld.long 0x00 10. " ENSPR3 ,The Short Packet Receive mode is set" "No,Yes" textline " " bitfld.long 0x00 9. " NACKRESP3 ,Nac response is instructed to bulk IN/OUT transfer" "Normal response,Nac response" bitfld.long 0x00 8. " NULLRESP3 ,It is a bit that demands an effective Null response for BULK IN/INTERRUPT IN" "Normal response,Null response" textline " " bitfld.long 0x00 7. " TESTMODE3 ,Test mode setting to endpoint3 is specified" "Normal response,Test mode" bitfld.long 0x00 6. " STALLDIS3 ,Stall initialization automatically is specified" "Automatically initialized,Not automatically initialized" textline " " bitfld.long 0x00 5. " TOGGLEDIS3 ,Toggle initialization automatically is specified" "Automatically initialized,Not automatically initialized" eventfld.long 0x00 4. " INISTALL3 ,This field is to instruct Stall initialization of endpoint3" "Not initialized,Initialized" textline " " eventfld.long 0x00 3. " INITOGGLE3 ,Initialization bit of Toggle of EndPoint3" "Not initialized,Initialized" bitfld.long 0x00 1. " REQSTALL3 ,Generation control bit of Stall when forwarding it to EndPoint" "Not returned,Returned" textline " " eventfld.long 0x00 0. " INIT3 ,This field is to instruct buffer initialization of endpoint3" "Not initialized,Initialized" group.long 0x11C++0x03 line.long 0x00 "EpS3,USB Function Endpoint3 Status Register" rbitfld.long 0x00 28.--31. " CRTINTF3 ,Interface value of endpoint3 is indicated" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" rbitfld.long 0x00 24.--27. " CRTALT3 ,Alternate value of endpoint3 is indicated" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 23. " INTCLSTALL3 ,It is an interrupt factor to show that Stall was released" "No interrupt,Interrupt" bitfld.long 0x00 22. " INTNACK3 ,IntNack3 interrupt request is indicated" "Not requested,Requested" textline " " bitfld.long 0x00 21. " INTSTALLED3 ,IntStalled3 interrupt request is indicated" "Not requested,Requested" bitfld.long 0x00 20. " INTEMPTY3 ,IntEmpty3 interrupt request is indicated" "Not requested,Requested" textline " " bitfld.long 0x00 19. " INTDEND3 ,IntDEnd3 interrupt request is indicated" "Not requested,Requested" bitfld.long 0x00 18. " INTACHG3 ,IntAChg3 interrupt request is indicated" "Not requested,Requested" textline " " bitfld.long 0x00 17. " INTPING3 ,IntPing3 interrupt request is indicated" "Not requested,Requested" bitfld.long 0x00 16. " INTREADY3 ,IntReady3 interrupt request is indicated" "Not possible,Possible" textline " " bitfld.long 0x00 14. " INTSPDD3 ,IntSPDD3 interrupt request is indicated" "No interrupt,Interrupt" bitfld.long 0x00 13. " INTSPR3 ,IntSPR3 interrupt request is indicated" "No interrupt,Interrupt" textline " " rbitfld.long 0x00 12. " EMPTY3 ,Whether endpoint3 buffer is empty is indicated" "Not empty,Empty" eventfld.long 0x00 3. " READY3O ,Data reading end instruction bit for EndPoint3 forwarding at Write" "No,Yes" textline " " eventfld.long 0x00 2. " READY3I ,Data writing end instruction bit for EndPoint3 forwarding at Write" "No,Yes" rbitfld.long 0x00 1. " STALLED3 ,Whether the state of endpoint3 is stall is indicated" "Not Stall,Stall" wgroup.long 0x180++0x0F line.long 0x00 "EPIB0,USB Function Endpoint0 IN Buffer Register" line.long 0x04 "EPIB1,USB Function Endpoint1 IN Buffer Register" line.long 0x08 "EPIB2,USB Function Endpoint2 IN Buffer Register" line.long 0x0C "EPIB3,USB Function Endpoint3 IN Buffer Register" rgroup.long 0x1C0++0x0B line.long 0x00 "EPOB0,USB Function Endpoint0 OUT Buffer Register" line.long 0x04 "EPOB1,USB Function Endpoint1 OUT Buffer Register" line.long 0x08 "EPOB2,USB Function Endpoint2 OUT Buffer Register" rgroup.long 0x200++0x13 line.long 0x00 "MAKE-UP_DATA,This register sets EndPoint information on Protocol Engine" line.long 0x04 "CONFIG0,UFConfig Register 0" bitfld.long 0x04 30.--31. " NUMTR ,NumTr" "0,1,2,3" hexmask.long.word 0x04 19.--29. 1. " SIZE ,Max. packet size setting of EndPoint0" textline " " bitfld.long 0x04 15.--18. " ALT ,Alt" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x04 11.--13. " INTF ,Intf" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x04 7.--10. " CONF ,Conf" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x04 5.--6. " TYPE ,EndPoint0 type setting" "Control,Isochronous,Bulk,Interrupt" textline " " bitfld.long 0x04 4. " IO ,EndPoint0 IN/OUT setting" "OUT,IN" bitfld.long 0x04 0.--3. " EPNUM ,EndPoint number setting" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "CONFIG1,UFConfig Register 1" bitfld.long 0x08 30.--31. " NUMTR ,NumTr" "0,1,2,3" hexmask.long.word 0x08 19.--29. 1. " SIZE ,Max. packet size setting of EndPoint0" textline " " bitfld.long 0x08 15.--18. " ALT ,Alt" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x08 11.--13. " INTF ,Intf" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x08 7.--10. " CONF ,Conf" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x08 5.--6. " TYPE ,EndPoint0 type setting" "Control,Isochronous,Bulk,Interrupt" textline " " bitfld.long 0x08 4. " IO ,EndPoint0 IN/OUT setting" "OUT,IN" bitfld.long 0x08 0.--3. " EPNUM ,EndPoint number setting" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x0C "CONFIG2,UFConfig Register 2" bitfld.long 0x0C 30.--31. " NUMTR ,NumTr" "0,1,2,3" hexmask.long.word 0x0C 19.--29. 1. " SIZE ,Max. packet size setting of EndPoint0" textline " " bitfld.long 0x0C 15.--18. " ALT ,Alt" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x0C 11.--13. " INTF ,Intf" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x0C 7.--10. " CONF ,Conf" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x0C 5.--6. " TYPE ,EndPoint0 type setting" "Control,Isochronous,Bulk,Interrupt" textline " " bitfld.long 0x0C 4. " IO ,ENDPOINT0 IN/OUT setting" "OUT,IN" bitfld.long 0x0C 0.--3. " EPNUM ,EndPoint number setting" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x10 "CONFIG3,UFConfig Register 3" bitfld.long 0x10 30.--31. " NUMTR ,NumTr" "0,1,2,3" hexmask.long.word 0x10 19.--29. 1. " SIZE ,Max. packet size setting of EndPoint0" textline " " bitfld.long 0x10 15.--18. " Alt ,Alt" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x10 11.--13. " INTF ,Intf" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x10 7.--10. " CONF ,Conf" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x10 5.--6. " TYPE ,EndPoint0 type setting" "Control,Isochronous,Bulk,Interrupt" textline " " bitfld.long 0x10 4. " IO ,EndPoint0 IN/OUT setting" "OUT,IN" bitfld.long 0x10 0.--3. " EPNUM ,EndPoint number setting" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" tree.end width 5. tree "Function Link DMAC Registers" group.long 0x404++0x07 line.long 0x00 "EPDC1,USB Function Endpoint1 DMA Control/Status Register" bitfld.long 0x00 8. " EPBT1 ,Undefined length burst transfer" "16,128" bitfld.long 0x00 7. " EPNF1 ,Whether Null packet is received is indicated" "Not received,Received" bitfld.long 0x00 6. " EPNE1 ,This is enable bit to Null packet reception interrupt" "Not occur,Occur" textline " " bitfld.long 0x00 5. " EPAI1 ,Update method of DMA transfer address is specified" "Repeatedly used,Performed" bitfld.long 0x00 4. " EPIO1 ,Endpoint1 IN/OUT is specified" "IN,OUT" bitfld.long 0x00 3. " EPDF1 ,This is status bit that shows fail/abort of DMA transfer" "Not occur,Occur" textline " " bitfld.long 0x00 2. " EPDM1 ,This is mask bit to DMA transfer end interrupt" "Not masked,Masked" bitfld.long 0x00 1. " EPDI1 ,This is status bit indicating occurrence of DMA transfer end interrupt request" "Not occur,Occur" bitfld.long 0x00 0. " EPDE1 ,This is DMA transfer enable bit" "Disabled,Enabled" line.long 0x04 "EPDC2,USB Function Endpoint2 DMA Control/Status Register" bitfld.long 0x04 8. " EPBT2 ,Undefined length burst transfer" "16,128" bitfld.long 0x04 7. " EPNF2 ,Whether Null packet is received is indicated" "Not received,Received" bitfld.long 0x04 6. " EPNE2 ,This is enable bit to Null packet reception interrupt" "Not occur,Occur" textline " " bitfld.long 0x04 5. " EPAI2 ,Update method of DMA transfer address is specified" "Repeatedly used,Performed" bitfld.long 0x04 4. " EPIO2 ,Endpoint2 IN/OUT is specified" "IN,OUT" bitfld.long 0x04 3. " EPDF2 ,This is status bit that shows fail/abort of DMA transfer" "Not occur,Occur" textline " " bitfld.long 0x04 2. " EPDM2 ,This is mask bit to DMA transfer end interrupt" "Not masked,Masked" bitfld.long 0x04 1. " EPDI2 ,This is status bit indicating occurrence of DMA transfer end interrupt request" "Not occur,Occur" bitfld.long 0x04 0. " EPDE2 ,This is DMA transfer enable bit" "Disabled,Enabled" group.long 0x414++0x07 line.long 0x00 "EPDA1,USB Function Endpoint1 DMA Address Register" line.long 0x04 "EPDA2,USB Function Endpoint2 DMA Address Register" group.long 0x424++0x07 line.long 0x00 "EPDS1,USB Function Endpoint1 DMA Size Register" line.long 0x04 "EPDS2,USB Function Endpoint2 DMA Size Register" tree.end width 0x0B tree.end endif tree "IDE66 (IDE Host Controller)" base ad:0x04900000 width 14. group.long 0x00++0x03 line.long 0x00 "CS0DAT,CS0 data register" hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Data" hexmask.long.byte 0x00 0.--7. 1. " DATA0 ,Data" group.long 0x04++0x03 line.long 0x00 "CS0ER/CS0FT,CS0 error/features register" bitfld.long 0x00 7. " FEATURES_7 ,Features 7" "0,1" bitfld.long 0x00 6. " WP ,WP" "0,1" bitfld.long 0x00 5. " MC ,MC" "0,1" bitfld.long 0x00 4. " INDF ,INDF" "0,1" textline " " bitfld.long 0x00 3. " MCR ,MCR" "0,1" bitfld.long 0x00 2. " ABRT ,ABRT" "0,1" bitfld.long 0x00 1. " NM ,NM" "0,1" bitfld.long 0x00 0. " MED ,MED" "0,1" group.long 0x08++0x13 line.long 0x00 "CS0SC,CS0 sector count register" hexmask.long.byte 0x00 0.--7. 1. " SC ,Sector Count" line.long 0x04 "CS0SN,CS0 sector number register" hexmask.long.byte 0x04 0.--7. 1. " SN ,Sector Number" line.long 0x08 "CS0CL,CS0 cylinder low register" hexmask.long.byte 0x08 0.--7. 1. " CL ,Cylinder Low" line.long 0x0C "CS0CH,CS0 cylinder high register" hexmask.long.byte 0x0C 0.--7. 1. " CH ,Cylinder High" line.long 0x10 "CS0DH,CS0 device/head register" bitfld.long 0x10 6. " L ,L" "0,1" bitfld.long 0x10 4. " DEV ,DEV" "0,1" bitfld.long 0x10 0.--3. " HEAD ,Head" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" group.long 0x1C++0x03 line.long 0x00 "CS0ST/CS0CMD,CS0 status/command register" bitfld.long 0x00 7. " BSY ,BSY" "0,1" bitfld.long 0x00 6. " DRDY ,DRDY" "0,1" bitfld.long 0x00 5. " DF ,DF" "0,1" bitfld.long 0x00 4. " DSC ,DSC" "0,1" textline " " bitfld.long 0x00 3. " DRQ ,DRQ" "0,1" bitfld.long 0x00 2. " CC1 ,Command Code" "0,1" bitfld.long 0x00 1. " CC0 ,Command Code" "0,1" bitfld.long 0x00 0. " ERR ,ERR" "0,1" rgroup.long 0x38++0x03 line.long 0x00 "CS1AS,CS1 alternate status register" bitfld.long 0x00 7. " BSY ,BSY" "0,1" bitfld.long 0x00 6. " DRDY ,DRDY" "0,1" bitfld.long 0x00 5. " DF ,DF" "0,1" bitfld.long 0x00 4. " DSC ,DSC" "0,1" textline " " bitfld.long 0x00 3. " DRQ ,DRQ" "0,1" bitfld.long 0x00 0. " ERR ,ERR" "0,1" wgroup.long 0x38++0x03 line.long 0x00 "CS1DC,CS1 device control register" bitfld.long 0x00 2. " SRST ,SRST" "0,1" bitfld.long 0x00 1. " XIEN ,XIEN" "0,1" textline " " group.long 0x40++0x03 line.long 0x00 "IDEDAT,Data register" hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Data" hexmask.long.byte 0x00 0.--7. 1. " DATA0 ,Data" group.long 0x48++0x0B line.long 0x00 "IDEPTCR,PIO timing control register" bitfld.long 0x00 4.--7. " ACTIVE_COUNT ,Access to IDE drive register and active time of IDE_XDIOR/IDE_XDIOW in PIO access are defined" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 0.--3. " RECOVERY_COUNT ,Access to IDE drive register and recovery time of IDE_XDIOR/IDE_XDIOW in PIO access are defined" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x04 "IDEPASR,PIO address setup register" bitfld.long 0x04 0.--2. " ADDRES_SETUP ,Address setup time of IDE_XDIOR/IDE_XDIOW" "8clocks,1clock,2clocks,3clocks,4clocks,5clocks,6clocks,7clocks" line.long 0x08 "IDEICMR,IDE command register" bitfld.long 0x08 7. " CSEL ,IDE_CSEL at IDE access is defined" "0,1" bitfld.long 0x08 6. " DRESET ,IDE_XDRESET output" "No reset,Reset" textline " " bitfld.long 0x08 5. " RST ,Internal macro is reset by writing '1'" "No reset,Reset" eventfld.long 0x08 3. " IC ,Interrupt Clear" "No reset,Reset" textline " " bitfld.long 0x08 2. " DMAID ,DMA Interface Direction" "Host->FIFO,FIFO->host" bitfld.long 0x08 1. " DMAIE ,DMA Interface Enable" "Disabled,Enabled" textline " " bitfld.long 0x08 0. " IE ,Interrupt Enable" "Disabled,Enabled" rgroup.long 0x54++0x03 line.long 0x00 "IDEISTR,IDE status register" bitfld.long 0x00 3. " XCBLID ,Input value to IDE_XCBLID pin is read" "0,1" bitfld.long 0x00 2. " XIOCS16 ,Input value to IDE_XIOCS16 pin is read" "0,1" textline " " bitfld.long 0x00 1. " XDASP ,Input value to IDE_XDASP pin is read" "0,1" bitfld.long 0x00 0. " INTRQ ,Input value to IDE_DINTRQ pin is read" "0,1" if (((per.l(ad:0x04900000+0x50))&0x01)==0x01) group.long 0x58++0x03 line.long 0x00 "IDEINER,Interrupt enable register" bitfld.long 0x00 2. " RX_FIFO ,RX_FIFO Empty" "Disabled,Enabled" bitfld.long 0x00 1. " TX_FIFO ,TX_FIFO Empty" "Disabled,Enabled" else hgroup.long 0x58++0x03 hide.long 0x00 "IDEINER,Interrupt enable register" in endif rgroup.long 0x5C++0x03 line.long 0x00 "IDEINSR,Interrupt status register" bitfld.long 0x00 2. " RX_FIFO_EMPTY ,Interrupt occurs by having reception's FIFO become full" "Not occurred,Occurred" bitfld.long 0x00 1. " TX_FIFO_EMPTY ,Interrupt occurs by having transmission's FIFO become empty" "Not occurred,Occurred" textline " " bitfld.long 0x00 0. " INTRQ ,Input value to IDE_DINTRQ pin is read as it is" "0,1" group.long 0x60++0x03 line.long 0x00 "IDEFCMR,FIFO command register" bitfld.long 0x00 3. " TX_FIFO_CLEAR ,Transmission FIFO is cleared" "Not cleared,Cleared" bitfld.long 0x00 2. " RX_FIFO_CLEAR ,Reception FIFO is cleared" "Not cleared,Cleared" textline " " bitfld.long 0x00 1. " TX_FIFO_ENABLE ,Transmission FIFO is enabled" "Disabled,Enabled" bitfld.long 0x00 0. " RX_FIFO_ENABLE ,Reception FIFO is enabled" "Disabled,Enabled" rgroup.long 0x64++0x03 line.long 0x00 "IDEFSTR,FIFO status register" bitfld.long 0x00 3. " TX_FIFO_FULL ,Transmission FIFO is full" "0,1" bitfld.long 0x00 2. " RX_FIFO_FULL ,Reception FIFO is full" "0,1" textline " " bitfld.long 0x00 1. " TX_FIFO_EMPTY ,Transmission FIFO is empty" "0,1" bitfld.long 0x00 0. " RX_FIFO_EMPTY ,Reception FIFO is empty" "0,1" rgroup.long 0x68++0x03 line.long 0x00 "IDETFCR,Transmission FIFO count register" hexmask.long.byte 0x00 0.--7. 1. " XCNT ,Status of transmission FIFO counter is indicated" group.long 0x70++0x03 line.long 0x00 "IDERFCR,Reception FIFO count register" bitfld.long 0x00 7. " RCNT[7] ,Status of reception FIFO counter" "0,1" bitfld.long 0x00 6. " [6] ,Status of reception FIFO counter" "0,1" textline " " bitfld.long 0x00 5. " [5] ,Status of reception FIFO counter" "0,1" bitfld.long 0x00 4. " [4] ,Status of reception FIFO counter" "0,1" textline " " rbitfld.long 0x00 3. " [3] ,Status of reception FIFO counter" "0,1" rbitfld.long 0x00 2. " [2] ,Status of reception FIFO counter" "0,1" textline " " rbitfld.long 0x00 1. " [1] ,Status of reception FIFO counter" "0,1" rbitfld.long 0x00 0. " [0] ,Status of reception FIFO counter" "0,1" group.long 0xC8++0x03 line.long 0x00 "IDEUTCR,UDMA timing control register" bitfld.long 0x00 4.--7. " ACTIVE_COUNT ,Active time of IDE_XDIOR" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 0.--3. " RECOVERY_COUNT ,Recovery time of IDE_XDIOR" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" group.long 0xD0++0x03 line.long 0x00 "IDEUCMR,UDMA command register" bitfld.long 0x00 3. " POT ,Pause_or_Term" "Pause phase,Termination phase" bitfld.long 0x00 2. " UDMA_DIRECTION ,Direction of Ultra DMA transfer is defined" "In burst,Out burst" textline " " bitfld.long 0x00 1. " UDMA_ENABLE ,Ultra DMA transfer is enabled" "Disabled,Enabled" rgroup.long 0xD4++0x03 line.long 0x00 "IDEUSTR,UDMA status register" bitfld.long 0x00 1. " UDMADATAOUT ,UDMA Data out Burst" "Stopped,In process" bitfld.long 0x00 0. " UDMADATAIN , UDMA Data in Burst" "Stopped,In process" group.long 0x150++0x0F line.long 0x00 "IDERRCC,RX_FIFO rest count compare value" hexmask.long.byte 0x00 0.--7. 1. " RRCC ,Comparison value of reception FIFO counter value" line.long 0x04 "IDEUTC1,Ultra DMA timing control 1" bitfld.long 0x04 4.--7. " TACK ,Setup and hold time for asserting/negating DMACK" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x04 0.--3. " TENV ,Envelope time" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "IDEUTC2,Ultra DMA timing control 2" bitfld.long 0x08 4.--7. " TLI ,Interlock time" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x08 0.--3. " TUI ,Interlock time" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x0C "IDEUTC3,Ultra DMA timing control 3" bitfld.long 0x0C 4.--7. " TSS ,Negating time of IDE_DDMARQ (DMARQ) or asserting time of IDE_XDIOW" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x0C 0.--3. " TMLI ,Interlock time" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" rgroup.long 0x200++0x03 line.long 0x00 "IDESTATUS,DMA status register" bitfld.long 0x00 0. " DMABSY ,IDE I/F is in DMA transfer" "Stopped,In process" textline " " group.long 0x204++0x1B line.long 0x00 "IDEINT,Interrupt register" bitfld.long 0x00 2. " DRIVE_ACCESS_ERROR ,IDE drive is accessed" "No interrupt,Interrupt" bitfld.long 0x00 1. " AHBMW_ERROR ,When response error occurs at accessing to AHB I/F master during DMA transfer" "No interrupt,Interrupt" textline " " bitfld.long 0x00 0. " DMA_END ,When data transfer of which number of data transfer is set to DTC and SC is completed" "No interrupt,Interrupt" line.long 0x04 "IDEINTMSK,Interrupt mask register" bitfld.long 0x04 4. " F_IDE66_MACRO_INT_MASK ,Mask of interrupt output" "Not masked,Masked" bitfld.long 0x04 2. " DRIVE_ACCESS_ERROR_MASK ,Mask of interrupt output" "Not masked,Masked" textline " " bitfld.long 0x04 1. " AHBMW_ERROR_MASK ,Mask of interrupt output" "Not masked,Masked" bitfld.long 0x04 0. " DMA_END_MASK ,Mask of interrupt output" "Not masked,Masked" line.long 0x08 "IDEPIOCTL,PIO access control register" bitfld.long 0x08 0. " PIO_CONTROL ,PIO access" "Default,Performed" line.long 0x0C "IDEDMACTL,DMA control register" bitfld.long 0x0C 31. " DMA_START ,This is start bit for DMA transfer" "Stopped,Started" bitfld.long 0x0C 0. " TRANS_MODE ,This bit sets transfer mode for DMA transfer" "512 byte,4 byte" line.long 0x10 "IDEDMATC,DMA transfer control register" hexmask.long.word 0x10 16.--24. 1. " DTC ,DMA Data Transfer Count" hexmask.long.byte 0x10 8.--15. 1. " SC ,Sector Count" textline " " bitfld.long 0x10 4.--5. " DIV ,Division of Increment Burst" "No division,64 burst,32 burst,Unused" bitfld.long 0x10 3. " INCR ,DMA Transfer Address Increment" "Increment,Fixed" textline " " bitfld.long 0x10 0.--2. " TYPE ,DMA Transfer Type" "Single,INCR,INCR4,INCR4,INCR8,INCR8,INCR16,INCR16" line.long 0x14 "IDEDMASAD,DMA source address register" line.long 0x18 "IDEDMADAD,DMA destination address register" width 0x0B tree.end tree "CCNT (Chip Controller)" base ad:0x3D100000 width 12. rgroup.long 0x00++0x03 line.long 0x00 "CINFO,Chip information" hexmask.long.byte 0x00 24.--31. 1. " 1ST_CODE ,This bitfield contains the first part of the product number (MB86R12) after the MB" hexmask.long.byte 0x00 16.--23. 1. " 2ND_CODE ,This bitfield contains the second part of the product number (MB86R12) after the MB" hexmask.long.word 0x00 4.--15. 1. " 3RD_CODE ,This bit is the 3rd_CODE information of the product number (MB86R12)" sif (cpuis("MB86R12")) bitfld.long 0x00 0.--3. " VER ,This bitfield contains the device version information of the chip" "0,ES1,ES2,3,4,5,6,7,8,9,10,11,12,13,14,15" else bitfld.long 0x00 0.--3. " VER ,This bitfield contains the device version information of the chip" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" endif group.long 0x100++0x03 line.long 0x00 "GLBLCTL,Global control" sif (cpu()=="MB86R12") bitfld.long 0x00 25. " ETHER_SEL ,The ethernet communication port is selected by the external pin or APIX(RX)" "External,APIX(RX)" bitfld.long 0x00 24. " I2S3_SEL ,The I2S3 communication port is selected by the external pin or APIX(RX)" "External,APIX(RX)" bitfld.long 0x00 19. " FLOW3_EN ,Enables/disables Flow control use permission for UART3 in UART mode" "Disabled,Enabled" bitfld.long 0x00 18. " FLOW2_EN ,Enables/disables Flow control use permission for UART2 in UART mode" "Disabled,Enabled" else bitfld.long 0x00 19. " FLOW3_EN ,Enables/disables Flow control use permission for UART3 in UART mode" "Disabled,Enabled" bitfld.long 0x00 18. " FLOW2_EN ,Enables/disables Flow control use permission for UART2 in UART mode" "Disabled,Enabled" endif textline " " bitfld.long 0x00 17. " FLOW1_EN ,Enables/disables Flow control use permission for UART1 in UART mode" "Disabled,Enabled" bitfld.long 0x00 16. " FLOW0_EN ,Enables/disables Flow control use permission for UART0 in UART mode" "Disabled,Enabled" bitfld.long 0x00 13. " UART5_MOD ,Selects the USART/UART mode of UART5" "USART,UART" bitfld.long 0x00 12. " UART4_MOD ,Selects the USART/UART mode of UART4" "USART,UART" textline " " bitfld.long 0x00 11. " UART3_MOD ,Selects the USART/UART mode of UART3" "USART,UART" bitfld.long 0x00 10. " UART2_MOD ,Selects the USART/UART mode of UART2" "USART,UART" bitfld.long 0x00 9. " UART1_MOD ,Selects the USART/UART mode of UART1" "USART,UART" bitfld.long 0x00 8. " UART0_MOD ,Selects the USART/UART mode of UART0" "USART,UART" textline " " bitfld.long 0x00 3. " CAN_MOD1 ,Selects mode of CAN channel 1" "Normal,IPC mode" bitfld.long 0x00 2. " CAN_MOD0 ,Selects mode of CAN channel 0" "Normal,IPC mode" sif (cpuis("MB86R11F")) bitfld.long 0x00 1. " USB_MOD ,The HOST/Function used on the USB can be selected" "HOST,FUNCTION" bitfld.long 0x00 0. " CS_MOD ,The number of the CS used on the External BUS can be selected" "CS0-CS2,CS0-CS1" else bitfld.long 0x00 0. " CS_MOD ,The number of the CS used on the External BUS can be selected" "CS0-CS2,CS0-CS1" endif textline " " if (((per.b(ad:0x3D100000+0x300))&0x10)==0x00) group.long 0x200++0x03 line.long 0x00 "PINMUX1,Pin Multiplex B-I" bitfld.long 0x00 31. " PMUX_EN ,Pinmux enable" "Unlock,Lock" bitfld.long 0x00 25.--27. " PMUX_I ,Pinmux I group" "CAP0,Ether CAP0,Ether GPIO,DISP2/I2C4/I2C3/PWM,,GPIO,?..." textline " " bitfld.long 0x00 22.--24. " PMUX_H ,Pinmux H group" "CAP2-3,CAP1/GPIO,CAP2/Serial TS IF0/Serial TS IF1,GPIO/I2S2/TS IF,ETM,GPIO,USART/UART4-5,?..." bitfld.long 0x00 19.--21. " PMUX_G ,Pinmux G group" "SPI0/CAN/MLB,PWM/CAN/I2S0,PWM/CAN/MLB,SPI0/CAN/I2S0,?..." textline " " bitfld.long 0x00 16.--18. " PMUX_F ,Pinmux F group" "USART4-5/SDIO/MMC0/DISP1/PWM/I2S0-1,DISP1/I2S1,USART/SDIO/MMC/APIX/AIC/I2S,IDE66,UART FLOW/Quad SPI/DISP1/PWM/I2S0-1,,USART/UART 4-5/SD,?..." bitfld.long 0x00 12.--14. " PMUX_E ,Pinmux E group" "USART0-3,IrDA/PWM,TCON,SPI/USART3,,GPIO,?..." textline " " bitfld.long 0x00 9.--11. " PMUX_D ,Pinmux D group" "DISP0,,,,,GPIO,?..." bitfld.long 0x00 6.--8. " PMUX_C ,Pinmux C group" "Related to interrupts,Related to interrupts I2C DMA,,Related to interrupts SPI1,?..." textline " " sif (cpuis("MB86R11F")) bitfld.long 0x00 3.--5. " PMUX_B ,Pinmux B group" "EBC,SPI1/I2S3,,ETM,,GPIO,?..." else bitfld.long 0x00 3.--5. " PMUX_B ,Pinmux B group" "MEMC,SDIO/MMC1/SPI1/I2S3,,ETM,,GPIO,?..." endif else group.long 0x200++0x03 line.long 0x00 "PINMUX1,Pin Multiplex B-I" bitfld.long 0x00 31. " PMUX_EN ,Pinmux enable" "Unlock,Lock" bitfld.long 0x00 25.--27. " PMUX_I ,Pinmux I group" "CAP0,Ether CAP0,Ether GPIO,DISP2/I2C4/I2C3/PWM,,GPIO,?..." textline " " bitfld.long 0x00 22.--24. " PMUX_H ,Pinmux H group" "CAP2-3,CAP1/GPIO,CAP2/Serial TS IF0/Serial TS IF1,GPIO/I2S2/TS IF,ETM,GPIO,USART/UART4-5,?..." bitfld.long 0x00 19.--21. " PMUX_G ,Pinmux G group" "SPI0/CAN/MLB,PWM/CAN/I2S0,PWM/CAN/MLB,SPI0/CAN/I2S0,?..." textline " " bitfld.long 0x00 16.--18. " PMUX_F ,Pinmux F group" "USART4-5/SDIO/MMC0/DISP1/PWM/I2S0-1,DISP1/I2S1,USART/SDIO/MMC/APIX/AIC/I2S,IDE66,UART FLOW/HS SPI/DISP1/PWM/I2S0-1,,USART/UART 4-5/SD,?..." bitfld.long 0x00 12.--14. " PMUX_E ,Pinmux E group" "USART0-3,IrDA/PWM,TCON,SPI/USART3,,GPIO,?..." textline " " bitfld.long 0x00 9.--11. " PMUX_D ,Pinmux D group" "DISP0,,,,,GPIO,?..." bitfld.long 0x00 6.--8. " PMUX_C ,Pinmux C group" "Related to interrupts,Related to interrupts I2C DMA,,Related to interrupts SPI1,?..." textline " " sif (cpuis("MB86R11F")) bitfld.long 0x00 3.--5. " PMUX_B ,Pinmux B group" "GPIO/Quad SPI,SPI1/I2S3,,ETM,,GPIO,?..." else bitfld.long 0x00 3.--5. " PMUX_B ,Pinmux B group" "GPIO/Quad SPI,SDIO/MMC1/SPI1/I2S3,,ETM,,GPIO,?..." endif endif group.long 0x204++0x03 line.long 0x00 "PINMUX2,Pin Multiplex J-L" bitfld.long 0x00 6.--8. " PMUX_L ,Pinmux L group" "USART3,IRDA/PWM,TCON,,USART3,GPIO,?..." bitfld.long 0x00 3.--5. " PMUX_K ,Pinmux K group" "USART2,IRDA,TCON,HS SPI,,GPIO,?..." textline " " bitfld.long 0x00 0.--2. " PMUX_J ,Pinmux J group" "USART1,IRDA,TCON,HS SPI,,GPIO,?..." textline " " if (((per.l(ad:0x3D100000))&0x0F)==0x01) sif (cpuis("MB86R12")) rgroup.long 0x300++0x03 line.long 0x00 "EXTFLASHST,External flash ROM type status" bitfld.long 0x00 0.--1. 3. 2. " EXTFLASHST ,Type information on Flash ROM connected with the outside by this bit can be confirmed" "32bit NOR Flash,32bit NOR Flash,32bit NOR Flash,Pinmux #A Serial Flash,16bit NOR Flash,,16bit NOR Flash,,NAND Flash,NAND Flash,NAND Flash,,NAND Flash,,NAND Flash," else rgroup.long 0x300++0x03 line.long 0x00 "EXTFLASHST,External flash ROM type status" bitfld.long 0x00 0.--1. 3. 2. " EXTFLASHST ,Type information on Flash ROM connected with the outside by this bit can be confirmed" "32bit NOR Flash,32bit NOR Flash,32bit NOR Flash,Pinmux #A Serial Flash,16bit NOR Flash,,16bit NOR Flash,Pinmux #B Serial Flash,NAND Flash,NAND Flash,NAND Flash,,NAND Flash,,NAND Flash," endif else rgroup.long 0x300++0x03 line.long 0x00 "EXTFLASHST,External flash ROM type status" bitfld.long 0x00 0.--1. 3. 2. " EXTFLASHST ,Type information on Flash ROM connected with the outside by this bit can be confirmed" "32bit NOR Flash,32bit NOR Flash,32bit NOR Flash,Pinmux #A Serial Flash,16bit NOR Flash,,16bit NOR Flash,Pinmux #B Serial Flash,NAND Flash,NAND Flash,NAND Flash,,NAND Flash,,NAND Flash," endif group.long 0x400++0x03 line.long 0x00 "IODRVCTL,IO buffer drive control" bitfld.long 0x00 4.--5. " DISP2_CDRV ,Driving control of Display2 buffer" "2mA,4mA,4mA,8mA" bitfld.long 0x00 2.--3. " DISP1_CDRV ,Driving control of Display1 buffer" "2mA,4mA,4mA,8mA" bitfld.long 0x00 0.--1. " DISP0_CDRV ,Driving control of Display0 buffer" "2mA,4mA,4mA,8mA" group.long 0x500++0x03 line.long 0x00 "CLKCTL,Clock control" bitfld.long 0x00 8. " BRG_EN ,AXI and AHB clock supplied to Bridge of GDC1 can be controlled" "Disabled,Enabled" bitfld.long 0x00 7. " WB_EN ,AXI and AHB clock supplied to Write Back can be controlled" "Disabled,Enabled" bitfld.long 0x00 6. " CAP3_EN ,AXI and AHB clock supplied to Capture3 can be controlled" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " CAP2_EN ,AXI and AHB clock supplied to Capture2 can be controlled" "Disabled,Enabled" bitfld.long 0x00 4. " CAP1_EN ,AXI and AHB clock supplied to Capture1 can be controlled" "Disabled,Enabled" bitfld.long 0x00 3. " CAP0_EN ,AXI and AHB clock supplied to Capture0 can be controlled" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " DISP2_EN ,Pixel ,Pixel ,Pixel, AXI and AHB clock supplied to Display2 can be controlled" "Disabled,Enabled" bitfld.long 0x00 1. " DISP1_EN ,Pixel ,Pixel ,Pixel, AXI and AHB clock supplied to Display1 can be controlled" "Disabled,Enabled" bitfld.long 0x00 0. " DISP0_EN ,Pixel ,Pixel ,Pixel, AXI and AHB clock supplied to Display0 can be controlled" "Disabled,Enabled" group.long 0x600++0x03 line.long 0x00 "SSCGCTL,CRG control" hexmask.long.word 0x00 19.--28. 1. " SSRATE ,This bit change the modulation rate of the SSCG unit in CRG_S" bitfld.long 0x00 18. " SSEN ,Enables/disables spread spectrum operation" "Disabled,Enabled" bitfld.long 0x00 16.--17. " SSFREQ ,The modulation frequency of the SSCG in CRG_S can be changed by this bit" "1/1024,1/2048,1/4096,1/4096" textline " " bitfld.long 0x00 8.--13. " IDIV_P ,The feedback divider ratio of the PLL in the CRG_P unit" ",,,,,,,,16,18,20,22,24,26,28,30,32,34,36,38,40,42,44,46,48,50,52,54,56,58,60,62,64,66,68,70,72,74,76,78,80,82,84,86,88,90,92,94,96,98,100,102,104,106,108,110,112,114,116,118,120,,," bitfld.long 0x00 2.--7. " IDIV_S ,The feedback divider ratio of the PLL in the CRG_S unit" ",,,,,,,,16,18,20,22,24,26,28,30,32,34,36,38,40,42,44,46,48,50,52,54,56,58,60,62,64,66,68,70,72,74,76,78,80,82,84,86,88,90,92,94,96,98,100,102,104,106,108,110,112,114,116,118,120,,," bitfld.long 0x00 1. " DISP_CKSEL ,Selects either the SSCG or PLL clock output to the display module" "SSCG CRG_S,PLL CRG_P" textline " " bitfld.long 0x00 0. " CLKSEL ,Selects either the SSCG or PLL clock output to each module" "SSCG CRG_S,PLL CRG_P" group.long 0x710++0x07 line.long 0x00 "PWMTRG1,PWM Trigger1 select" bitfld.long 0x00 28.--31. " PWM[7] ,This bit selects the external trigger input for ch3 (PWM7) of the PWM_1 module" "PWMTRG0,PWMTRG1,PWMTRG2,PWMTRG3,PWMTRG4,PWMTRG5,PWMTRG6,PWMTRG7,PWMTRG8,PWMTRG9,PWMTRG10,PWMTRG11,PWMTRG12,PWMTRG13,PWMTRG14,PWMTRG15" bitfld.long 0x00 24.--27. " [6] ,This bit selects the external trigger input for ch3 (PWM6) of the PWM_1 module" "PWMTRG0,PWMTRG1,PWMTRG2,PWMTRG3,PWMTRG4,PWMTRG5,PWMTRG6,PWMTRG7,PWMTRG8,PWMTRG9,PWMTRG10,PWMTRG11,PWMTRG12,PWMTRG13,PWMTRG14,PWMTRG15" bitfld.long 0x00 20.--23. " [5] ,This bit selects the external trigger input for ch3 (PWM5) of the PWM_1 module" "PWMTRG0,PWMTRG1,PWMTRG2,PWMTRG3,PWMTRG4,PWMTRG5,PWMTRG6,PWMTRG7,PWMTRG8,PWMTRG9,PWMTRG10,PWMTRG11,PWMTRG12,PWMTRG13,PWMTRG14,PWMTRG15" textline " " bitfld.long 0x00 16.--19. " [4] ,This bit selects the external trigger input for ch3 (PWM4) of the PWM_1 module" "PWMTRG0,PWMTRG1,PWMTRG2,PWMTRG3,PWMTRG4,PWMTRG5,PWMTRG6,PWMTRG7,PWMTRG8,PWMTRG9,PWMTRG10,PWMTRG11,PWMTRG12,PWMTRG13,PWMTRG14,PWMTRG15" bitfld.long 0x00 12.--15. " [3] ,This bit selects the external trigger input for ch3 (PWM3) of the PWM_0 module" "PWMTRG0,PWMTRG1,PWMTRG2,PWMTRG3,PWMTRG4,PWMTRG5,PWMTRG6,PWMTRG7,PWMTRG8,PWMTRG9,PWMTRG10,PWMTRG11,PWMTRG12,PWMTRG13,PWMTRG14,PWMTRG15" bitfld.long 0x00 8.--11. " [2] ,This bit selects the external trigger input for ch3 (PWM2) of the PWM_0 module" "PWMTRG0,PWMTRG1,PWMTRG2,PWMTRG3,PWMTRG4,PWMTRG5,PWMTRG6,PWMTRG7,PWMTRG8,PWMTRG9,PWMTRG10,PWMTRG11,PWMTRG12,PWMTRG13,PWMTRG14,PWMTRG15" textline " " bitfld.long 0x00 4.--7. " [1] ,This bit selects the external trigger input for ch3 (PWM1) of the PWM_0 module" "PWMTRG0,PWMTRG1,PWMTRG2,PWMTRG3,PWMTRG4,PWMTRG5,PWMTRG6,PWMTRG7,PWMTRG8,PWMTRG9,PWMTRG10,PWMTRG11,PWMTRG12,PWMTRG13,PWMTRG14,PWMTRG15" bitfld.long 0x00 0.--3. " [0] ,This bit selects the external trigger input for ch3 (PWM0) of the PWM_0 module" "PWMTRG0,PWMTRG1,PWMTRG2,PWMTRG3,PWMTRG4,PWMTRG5,PWMTRG6,PWMTRG7,PWMTRG8,PWMTRG9,PWMTRG10,PWMTRG11,PWMTRG12,PWMTRG13,PWMTRG14,PWMTRG15" line.long 0x04 "PWMTRGSEL2,PWM trigger2 select" bitfld.long 0x04 12.--15. " [11] ,This bit selects the external trigger input for ch3 (PWM11) of the PWM_2 module" "PWMTRG0,PWMTRG1,PWMTRG2,PWMTRG3,PWMTRG4,PWMTRG5,PWMTRG6,PWMTRG7,PWMTRG8,PWMTRG9,PWMTRG10,PWMTRG11,PWMTRG12,PWMTRG13,PWMTRG14,PWMTRG15" bitfld.long 0x04 8.--11. " [10] ,This bit selects the external trigger input for ch3 (PWM10) of the PWM_2 module" "PWMTRG0,PWMTRG1,PWMTRG2,PWMTRG3,PWMTRG4,PWMTRG5,PWMTRG6,PWMTRG7,PWMTRG8,PWMTRG9,PWMTRG10,PWMTRG11,PWMTRG12,PWMTRG13,PWMTRG14,PWMTRG15" bitfld.long 0x04 4.--7. " [9] ,This bit selects the external trigger input for ch3 (PWM9) of the PWM_2 module" "PWMTRG0,PWMTRG1,PWMTRG2,PWMTRG3,PWMTRG4,PWMTRG5,PWMTRG6,PWMTRG7,PWMTRG8,PWMTRG9,PWMTRG10,PWMTRG11,PWMTRG12,PWMTRG13,PWMTRG14,PWMTRG15" textline " " bitfld.long 0x04 0.--3. " [8] ,This bit selects the external trigger input for ch3 (PWM8) of the PWM_2 module" "PWMTRG0,PWMTRG1,PWMTRG2,PWMTRG3,PWMTRG4,PWMTRG5,PWMTRG6,PWMTRG7,PWMTRG8,PWMTRG9,PWMTRG10,PWMTRG11,PWMTRG12,PWMTRG13,PWMTRG14,PWMTRG15" group.long 0x800++0x03 line.long 0x00 "ETHERCTL,Ethernet control" bitfld.long 0x00 3. " FLOWCTL ,The flow control enables/dsiables the use of full or half duplex transmission modes" "Disabled,Enabled" sif (cpuis("MB86R11F")) bitfld.long 0x00 0.--2. " PHY_INTF_SEL ,This bit changes the Ethernet PHY interface mode" "GMII/MII,RGMII,,,RMII,?..." else bitfld.long 0x00 0.--2. " PHY_INTF_SEL ,This bit changes the Ethernet PHY interface mode" "GMII/MII,,RMII,,RMII,?..." endif sif (cpuis("MB86R12")) group.long 0xC00++0x07 line.long 0x00 "APIXCTL,APIX control" bitfld.long 0x00 0. " I2S_CKSEL ,Selects the master clock from I2S input to APIX" "AHB clock 1/8,ECLK same as I2S ECLK" line.long 0x04 "SDIOCTL,SDIO control" bitfld.long 0x04 0. " SDS ,Sync Down Control" "Off,On" endif width 0x0B tree.end tree "EXIRC (External interrupt controller)" tree "EXIRC 0" base ad:0x3B400000 width 7. group.long 0x00++0x0B line.long 0x00 "EIENB,External Interrupt Enable Register" bitfld.long 0x00 3. " ENB3 ,Masking external interrupt request Status(INT_A[3] pin)" "Disabled,Enabled" bitfld.long 0x00 2. " ENB2 ,Masking external interrupt request Status(INT_A[2] pin)" "Disabled,Enabled" bitfld.long 0x00 1. " ENB1 ,Masking external interrupt request Status(INT_A[1] pin)" "Disabled,Enabled" bitfld.long 0x00 0. " ENB0 ,Masking external interrupt request Status(INT_A[0] pin)" "Disabled,Enabled" line.long 0x04 "EIREQ,External Interrupt Request Register" bitfld.long 0x04 3. " REQ3 ,External interrupt 3 (INT_A[3] pin)" "No interrupt,Interrupt" bitfld.long 0x04 2. " REQ2 ,External interrupt 2 (INT_A[2] pin)" "No interrupt,Interrupt" bitfld.long 0x04 1. " REQ1 ,External interrupt 1 (INT_A[1] pin)" "No interrupt,Interrupt" bitfld.long 0x04 0. " REQ0 ,External interrupt 0 (INT_A[0] pin)" "No interrupt,Interrupt" line.long 0x08 "EILVL,External Interrupt Level Register" bitfld.long 0x08 6.--7. " LVL3 ,External interrupt channel 3" "L level,H level,Rising edge,Falling edge" bitfld.long 0x08 4.--5. " LVL2 ,External interrupt channel 2" "L level,H level,Rising edge,Falling edge" bitfld.long 0x08 2.--3. " LVL1 ,External interrupt channel 1" "L level,H level,Rising edge,Falling edge" bitfld.long 0x08 0.--1. " LVL0 ,External interrupt channel 0" "L level,H level,Rising edge,Falling edge" width 0x0B tree.end tree "EXIRC 1" base ad:0x3B410000 width 7. group.long 0x00++0x0B line.long 0x00 "EIENB,External Interrupt Enable Register" bitfld.long 0x00 3. " ENB3 ,Masking external interrupt request Status(INT_A[3] pin)" "Disabled,Enabled" bitfld.long 0x00 2. " ENB2 ,Masking external interrupt request Status(INT_A[2] pin)" "Disabled,Enabled" bitfld.long 0x00 1. " ENB1 ,Masking external interrupt request Status(INT_A[1] pin)" "Disabled,Enabled" bitfld.long 0x00 0. " ENB0 ,Masking external interrupt request Status(INT_A[0] pin)" "Disabled,Enabled" line.long 0x04 "EIREQ,External Interrupt Request Register" bitfld.long 0x04 3. " REQ3 ,External interrupt 3 (INT_A[3] pin)" "No interrupt,Interrupt" bitfld.long 0x04 2. " REQ2 ,External interrupt 2 (INT_A[2] pin)" "No interrupt,Interrupt" bitfld.long 0x04 1. " REQ1 ,External interrupt 1 (INT_A[1] pin)" "No interrupt,Interrupt" bitfld.long 0x04 0. " REQ0 ,External interrupt 0 (INT_A[0] pin)" "No interrupt,Interrupt" line.long 0x08 "EILVL,External Interrupt Level Register" bitfld.long 0x08 6.--7. " LVL3 ,External interrupt channel 3" "L level,H level,Rising edge,Falling edge" bitfld.long 0x08 4.--5. " LVL2 ,External interrupt channel 2" "L level,H level,Rising edge,Falling edge" bitfld.long 0x08 2.--3. " LVL1 ,External interrupt channel 1" "L level,H level,Rising edge,Falling edge" bitfld.long 0x08 0.--1. " LVL0 ,External interrupt channel 0" "L level,H level,Rising edge,Falling edge" width 0x0B tree.end tree.end tree "IRDA (Infrared Data Association)" base ad:0xD0410000 width 8. group.long 0x00++0x3 line.long 0x00 "FDATA,FIFO Data Register" hexmask.long.byte 0x00 0.--7. 1. " DATA ,FIFO DATA" if (((per.l(ad:0xD0410000+0x54))&0xE0)==0x60) group.long 0x04++0x03 line.long 0x00 "IER,Interrupt Enable Register" bitfld.long 0x00 7. " TMIE ,GP Timer Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 2. " LSIE ,Receiver Line Status Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " TLIE ,Transmitter Low Data Level Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 0. " RLIE ,Receiver High Data Level Interrupt Enable" "Disabled,Enabled" rgroup.long 0x08++0x03 line.long 0x00 "IIR,Interrupt Identification Register" bitfld.long 0x00 6.--7. " FIE ,FIFO Enable Status" ",,,FIFO Mode" bitfld.long 0x00 3. " TMI ,RX FIFO Timeout Interrupt" "Stopped,Generated" textline " " bitfld.long 0x00 1.--2. " ILV ,Interrupt Level" ",Level 3,Level 2,Level 1" bitfld.long 0x00 0. " IPD ,Interrupt Pending" "Generated,Stopped" group.long 0x0C++0x03 line.long 0x00 "LCR,Link Control Register" bitfld.long 0x00 2. " STL ,Stop bit Length" "1 bit,1.5/2 bits" bitfld.long 0x00 0.--1. " CHL ,Character Length" "5bits,6bits,7bits,8bits" rgroup.long 0x14++0x03 line.long 0x00 "LSR,Link Status Register" bitfld.long 0x00 7. " FE ,FIFO Error" "No error,Error" bitfld.long 0x00 6. " TE ,Transmitter Empty" "Not empty,Empty" textline " " bitfld.long 0x00 5. " TDRE ,Transmitter Data Register Empty" "Not empty,Empty" bitfld.long 0x00 4. " BED ,Break Event Detected" "Not detected,Detected" textline " " bitfld.long 0x00 3. " FME ,Framing Error" "No error,Error" bitfld.long 0x00 1. " OVE ,Overrun Error" "No error,Error" textline " " bitfld.long 0x00 0. " RDA ,Receiver Data Available" "Not ready,Ready" group.long 0x28++0x03 line.long 0x00 "FCR,FIFO Control Register" bitfld.long 0x00 6.--7. " RTL ,RX_FIFO drq & interrupt Trigger Level" "Level 1,Level 8,Level 16,Level 30" textline " " bitfld.long 0x00 2. " TFR ,Transmitter soft Reset" "Not cleared,Cleared" bitfld.long 0x00 1. " RFR ,Receiver soft Reset" "Not cleared,Cleared" textline " " bitfld.long 0x00 0. " FEN ,Enable Fifos" "No,Yes" elif ((((per.l(ad:0xD0410000+0x54))&0xE0)==0x80)||(((per.l(ad:0xD0410000+0x54))&0xE0)==0xA0)) group.long 0x04++0x03 line.long 0x00 "IER,Interrupt Enable Register" bitfld.long 0x00 7. " TMIE ,GP Timer Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 6. " SFIE ,ST_FIFO Event Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " TEIE ,Transmitter Empty/Pipeline Load" "Disabled,Enabled" bitfld.long 0x00 4. " DMIE ,DMA Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " LSIE ,Receiver Line Status Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 1. " TLIE ,Transmitter Low Data Level Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " RLIE ,Receiver High Data Level Interrupt Enable" "Disabled,Enabled" rgroup.long 0x08++0x03 line.long 0x00 "IIR,Interrupt Identification Register" bitfld.long 0x00 7. " TMEV ,General purpose Timer event" ",Timer value 0" bitfld.long 0x00 6. " SFEV ,ST_FIFO Timeout generation" "Not generated,Generated" textline " " bitfld.long 0x00 5. " TEEV ,Transmitter Empty/Pipeline load Event" "Pipeline empty,Writting data ongoing" bitfld.long 0x00 4. " DMEV ,DMA Event" "Not completed,Completed" textline " " bitfld.long 0x00 2. " LSEV ,Link Status Event" ",All conditions applied" bitfld.long 0x00 1. " TLEV ,Transmitter Low data level Event" "Exceeds Threshold,Threshold or less" textline " " bitfld.long 0x00 0. " RLEV ,Receiver high data Level Event" "Not reached,Reached" group.long 0x0C++0x03 line.long 0x00 "LCR,Link Control Register" bitfld.long 0x00 2. " STL ,Stop bit Length" "0,1" bitfld.long 0x00 0.--1. " CHL ,Character Length" "5bits,6bits,7bits,8bits" rgroup.long 0x14++0x03 line.long 0x00 "LSR,Link Status Register" bitfld.long 0x00 7. " FE ,Frame End" "Not reached,Reached" bitfld.long 0x00 6. " TE ,Transmitter Empty" "Not empty,Empty" textline " " bitfld.long 0x00 5. " TMFE ,Transmitter FIFO Empty" "Not empty,Empty" bitfld.long 0x00 4. " ML ,Maximum Length" "No maximum,Maximum" textline " " bitfld.long 0x00 3. " PLE ,Physical Layer Error" "Not occurred,Occurred" bitfld.long 0x00 2. " CRE ,CRC Error" "Not occurred,Occurred" textline " " bitfld.long 0x00 1. " OVE ,Overrun Error" "Not generated,Generated" bitfld.long 0x00 0. " RDA ,Receiver Data Available" "Not ready,Ready" group.long 0x1C++0x03 line.long 0x00 "SCR,Scratchpad Register" rbitfld.long 0x00 7. " PLOT ,Pipeline Load Status" "No,Yes" bitfld.long 0x00 6. " TMUD ,Transmitter Underrun" "No,Yes" textline " " rbitfld.long 0x00 5. " RESY ,Receiver busy" "No,Yes" rbitfld.long 0x00 4. " LFRF ,Lost Frame Flag" "Frame,No frame" textline " " bitfld.long 0x00 3. " THFE ,Transmitter Halted on Frame End" "Ongoing,Completed" bitfld.long 0x00 2. " SEOT ,Set End Of Transmission" "Ongoing,Completed" textline " " rbitfld.long 0x00 1. " EOF ,EOF byte in RX FIFO" "No EOF,EOF" rbitfld.long 0x00 0. " RFTO ,RX FIFO TimeOut" "No,Yes" group.long 0x28++0x03 line.long 0x00 "FCR,FIFO Control Register" bitfld.long 0x00 6.--7. " RTL ,RX_FIFO drq & interrupt Trigger Level" "Level 1,Level 8,Level 16,Level 30" bitfld.long 0x00 4.--5. " TTL ,TX_FIFO drq Trigger Level" "Level 1,Level 8,Level 16,Level 32" textline " " bitfld.long 0x00 2. " TFR ,Transmitter soft Reset" "Not cleared,Cleared" bitfld.long 0x00 1. " RFR ,Receiver soft Reset" "Not cleared,Cleared" else hgroup.long 0x04++0x03 hide.long 0x00 "IER,Interrupt Enable Register" hgroup.long 0x08++0x03 hide.long 0x00 "IIR,Interrupt Identification Register" hgroup.long 0x14++0x03 hide.long 0x00 "LSR,Link Status Register" hgroup.long 0x1C++0x03 hide.long 0x00 "SCR,Scratchpad Register" hgroup.long 0x28++0x03 hide.long 0x00 "FCR,FIFO Control Register" endif group.long 0x40++0x07 line.long 0x00 "BGDL,Baud Generator Divisor Data (Lower)" hexmask.long.byte 0x00 0.--7. 1. " BLDATA ,Baud generator divisor Lower DATA" line.long 0x04 "BGDU,Baud Generator Divisor Data (Upper)" hexmask.long.byte 0x04 0.--7. 1. " BLDATA ,Baud generator divisor Lower DATA" group.long 0x54++0x03 line.long 0x00 "MDR,Mode Select Register" bitfld.long 0x00 5.--7. " MDSL ,Mode SeLect" ",,,SIR,MIR,FIR,," bitfld.long 0x00 4. " SIP ,Send Interaction Pulse(MIR FIR mode)" "0,Sent" textline " " bitfld.long 0x00 3. " TDF ,Transmit DeFerral" "Disabled,Enabled" bitfld.long 0x00 2. " DMAE ,DMA Enable" "Disabled,Enabled" rgroup.long 0x58++0x07 line.long 0x00 "TFLV,TX_FIFO Level Select Register" bitfld.long 0x00 0.--5. " TFLV ,TX Fifo Level" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x04 "RFLV,RX_FIFO Level Select Register" bitfld.long 0x04 0.--5. " RFLV ,RX Fifo Level" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" group.long 0x80++0x0B line.long 0x00 "GTIML,General Purpose Timer Count (Lower) Register" hexmask.long.byte 0x00 0.--7. 1. " GLDATA ,General-purpose timer Lower DATA" line.long 0x04 "GTMU,General Purpose Timer Count (Upper) Register" bitfld.long 0x04 0.--3. " GUDATA ,General-purpose timer Upper DATA" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "IRCR1,Infrared Control 1 Register" bitfld.long 0x08 7. " CTE2 ,Timer Event Interrupt is released" "Disabled,Enabled" rbitfld.long 0x08 3. " TMREV2 ,TMREV2 timer event" "No,Yes" textline " " bitfld.long 0x08 2. " TMST ,Timer Start R/W" "Stop/Ending,Executed/Reload" bitfld.long 0x08 1. " CTRD ,Counter Read" "Count value,Set value" textline " " bitfld.long 0x08 0. " TMEN ,Timer Enable" "Disabled,Enabled" group.long 0x90++0x0F line.long 0x00 "TFLL,Transmit Frame Length(Lower) Register" hexmask.long.byte 0x00 0.--7. 1. " TLDATA ,Transmit frame length Lower DATA" line.long 0x04 "TFLU,Transmit Frame Length(Upper) Register" bitfld.long 0x04 0.--4. " TUDATA ,Transmit frame length Upper DATA" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x08 "RFLL,Receive Frame Length(Lower) Register" hexmask.long.byte 0x08 0.--7. 1. " RLDATA ,Receive frame length Lower DATA" line.long 0x0C "RFLU,Receive Frame Length(Upper) Register" bitfld.long 0x0C 0.--4. " RUDATA ,Receive frame length Upper DATA" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0xA8++0x07 line.long 0x00 "PMDR,Pipeline Mode Register" bitfld.long 0x00 5.--7. " PLMD ,PipeLine Mode select" ",,,,MIR,FIR,," bitfld.long 0x00 2. " PDME ,Pipeline DMA Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " MBPE ,Mode Bits Pipeline Enable" "Disabled,Enabled" group.long 0xB0++0x03 line.long 0x00 "IRCR2,Infrared Control 2 Register" bitfld.long 0x00 6. " SFTH ,Status FIFO ThresHold select" "Level 2,Level 4" bitfld.long 0x00 5. " FREC ,Fame End Control" "Usually,DMA mode" textline " " bitfld.long 0x00 3. " TMD ,Transmission end stop mode" "Disabled,Enabled" bitfld.long 0x00 2. " MRSL ,MiR data rate Select" "1.152 Mbps,0.576 Mbps" if (((per.l(ad:0xD0410000+0x54))&0xE0)==0x80) group.long 0xB4++0x03 line.long 0x00 "FRST,Frame Status Register" bitfld.long 0x00 7. " VLD ,ST Fifo entry Valid" "No effective,Effective" bitfld.long 0x00 6. " LTFR ,Lost Frame Indicator Flag" "No error,Error" textline " " bitfld.long 0x00 4. " MFLE ,Max Frame Length Exceed" "Not received,Received" bitfld.long 0x00 3. " PHLE ,Physical Layer Error" "Not aborted,Aborted" textline " " bitfld.long 0x00 2. " CRCE ,CRC Error" "Not occurred,Occurred" bitfld.long 0x00 1. " OERF ,Overrun Error of Rx_Fifo" "No error,Error" textline " " bitfld.long 0x00 0. " OESF ,Overrun Error of St_Fifo" "No error,Error" elif (((per.l(ad:0xD0410000+0x54))&0xE0)==0xA0) group.long 0xB4++0x03 line.long 0x00 "FRST,Frame Status Register" bitfld.long 0x00 7. " VLD ,ST Fifo entry Valid" "No effective,Effective" bitfld.long 0x00 6. " LTFR ,Lost Frame Indicator Flag" "No error,Error" textline " " bitfld.long 0x00 4. " MFLE ,Max Frame Length Exceed" "Not received,Received" bitfld.long 0x00 3. " PHLE ,Physical Layer Error" "No error,Error" textline " " bitfld.long 0x00 2. " CRCE ,CRC Error" "Not occurred,Occurred" bitfld.long 0x00 1. " OERF ,Overrun Error of Rx_Fifo" "No error,Error" textline " " bitfld.long 0x00 0. " OESF ,Overrun Error of St_Fifo" "No error,Error" endif rgroup.long 0xB8++0x07 line.long 0x00 "FRLL,Received Frame Length(Lower) Register" hexmask.long.byte 0x00 0.--7. 1. " RLDATA ,Receive frame length Lower DATA" line.long 0x04 "FRLU,Received Frame Length(Upper) Register" hexmask.long.byte 0x04 0.--7. 1. " RUDATA ,Receive frame length Upper DATA" group.long 0xC0++0x03 line.long 0x00 "IRCR3,Infrared Control 3 Register" bitfld.long 0x00 2. " ICRC ,Invert transmitter CRC" "Transmitted,Reverses and transmitted" bitfld.long 0x00 1. " DCRC ,Disable transmitter CRC" "Transmitted,Not transmitted" if (((per.l(ad:0xD0410000+0xB0))&0x04)==0x04) group.long 0xC4++0x03 line.long 0x00 "MIRPW,MIR Pluse Width Register" bitfld.long 0x00 0.--3. " MPW ,MIR Signal Pulse Width" "-,-,-,-,166.66 ns,208.33 ns,250 ns,291.56 ns,333.33 ns,374.99 ns,416.66 ns,458.33 ns,500 ns,541.66 ns,583.32 ns,625 ns" else group.long 0xC4++0x03 line.long 0x00 "MIRPW,MIR Pluse Width Register" bitfld.long 0x00 0.--3. " MPW ,MIR Signal Pulse Width" "-,-,-,-,83.33 ns,104.16ns,125 ns,145.83 ns,166.66 ns,187.50 ns,208.33 ns,229.16ns,250 ns,270.83 ns,291.66 ns,312.5 ns" endif group.long 0xC8++0x03 line.long 0x00 "SIRPW,SIR Pluse Width" bitfld.long 0x00 0.--3. " SPW ,SIR signal Pulse Width" "3/(16 * baud rate value (bps)),3/(16 * baud rate value (bps)),3/(16 * baud rate value (bps)),3/(16 * baud rate value (bps)),3/(16 * baud rate value (bps)),3/(16 * baud rate value (bps)),3/(16 * baud rate value (bps)),3/(16 * baud rate value (bps)),3/(16 * baud rate value (bps)),3/(16 * baud rate value (bps)),3/(16 * baud rate value (bps)),3/(16 * baud rate value (bps)),3/(16 * baud rate value (bps)),1.625 us,3/(16 * baud rate value (bps)),3/(16 * baud rate value (bps))" group.long 0xD0++0x03 line.long 0x00 "BFPL,Beginning Flag/ Preamble Length Register" bitfld.long 0x00 4.--7. " MBF ,MIR Beginning Flags" ",1,2,3,4,5,6,8,10,12,16,20,24,28,32," bitfld.long 0x00 0.--3. " FPL ,FIR Preamble Length" ",1,2,3,4,5,6,8,10,12,16,20,24,28,32," group.long 0xDC++0x03 line.long 0x00 "FIRPW,FIR Pluse Width Register" bitfld.long 0x00 2. " SPWS ,Single Pulse Width minimum Select" "62.5 ns,41.7 ns" bitfld.long 0x00 0.--1. " DPWS ,Double Pulse Width Select" "66.7 ns,187.2 ns,208.0 ns," if (((per.l(ad:0xD0410000+0xFC))&0x80)==0x00) group.long 0xF0++0x03 line.long 0x00 "IRCFG1,Infrared Interface Configuration 1 Register" bitfld.long 0x00 7. " DS2O ,Direction of IRCFG1[2:0]" "ID,Written IRSL" textline " " rbitfld.long 0x00 3. " TI ,Transceiver Identification" "0,1" bitfld.long 0x00 0.--2. " ICON ,Transceiver Identification/Control" "0,1,2,3,4,5,6,7" textline " " else if (((per.l(ad:0xD0410000+0x54))&0xE0)==0x60) group.long 0xF0++0x03 line.long 0x00 "IRCFG1,Infrared Interface Configuration 1 Register" bitfld.long 0x00 7. " DS2O ,Direction of IRCFG1[2:0]" "ID,Written IRSL" bitfld.long 0x00 4.--6. " SIRC ,SIR mode transceiver Configuration" "0,1,2,3,4,5,6,7" textline " " rbitfld.long 0x00 3. " TI ,Transceiver Identification" "0,1" textline " " elif (((per.l(ad:0xD0410000+0x54))&0xE0)==0xA0) group.long 0xF0++0x03 line.long 0x00 "IRCFG1,Infrared Interface Configuration 1 Register" bitfld.long 0x00 7. " DS2O ,Direction of IRCFG1[2:0]" "ID,Written IRSL" textline " " rbitfld.long 0x00 3. " TI ,Transceiver Identification" "0,1" group.long 0xF4++0x03 line.long 0x00 "IRCFG2,Infrared Interface Configuration 2 Register" bitfld.long 0x00 4.--6. " FIRC ,FIR mode transceiver Configuration" "0,1,2,3,4,5,6,7" elif (((per.l(ad:0xD0410000+0x54))&0xE0)==0x80) group.long 0xF0++0x03 line.long 0x00 "IRCFG1,Infrared Interface Configuration 1 Register" bitfld.long 0x00 7. " DS2O ,Direction of IRCFG1[2:0]" "ID,Written IRSL" textline " " rbitfld.long 0x00 3. " TI ,Transceiver Identification" "0,1" group.long 0xF4++0x03 line.long 0x00 "IRCFG2,Infrared Interface Configuration 2 Register" bitfld.long 0x00 0.--2. " MIRC ,MIR mode transceiver Configuration" "0,1,2,3,4,5,6,7" endif endif group.long 0xFC++0x03 line.long 0x00 "IRCFG4,Infrared Interface Configuration 4 Register" bitfld.long 0x00 7. " AMCF ,Automatic infrared Transceiver Configuration" "Disabled,Enabled" bitfld.long 0x00 4. " RINV ,A receiving optical module is to correspond to IRRX of reverse-logic" "Active low,Active height" width 0x0B tree.end tree "SIG (Signature Unit)" tree "SIG 0" base ad:0x38200000 width 30. group.long 0x00++0x03 line.long 0x00 "LOCKUNLOCK,Lock/unlock Signature Unit Register" rgroup.long 0x04++0x03 line.long 0x00 "LOCKSTATUS,Lock Status Register" bitfld.long 0x00 0. " LOCKSTATUS ,Lock status" "Unlocked,Locked" group.long 0x08++0x5F line.long 0x00 "SWRESET,Software Reset Register" bitfld.long 0x00 0. " SWRES ,Software reset" "No reset,Reset" line.long 0x04 "CTRL,General Configuration Register" bitfld.long 0x04 16.--17. " SRCSEL ,Source select" "Source 0,Source 1,Source 2,Source 3" bitfld.long 0x04 8.--9. " VMASK_MODE ,Mask window handling (vertical coordinates)" "Not masked,Inside,Outside,?..." textline " " bitfld.long 0x04 0.--1. " HMASK_MODE ,Mask window handling (horizontal coordinates)" "Not masked,Inside,Outside,?..." line.long 0x08 "MASKHORIZONTALUPPERLEFT,Mask Window Horizontal Coordinates Register" bitfld.long 0x08 11. " MASKHORIZONTALUPPERLEFT ,Mask coordinates bit 11" "0,1" bitfld.long 0x08 10. ",Mask coordinates bit 10" "0,1" bitfld.long 0x08 9. ",Mask coordinates bit 9" "0,1" bitfld.long 0x08 8. ",Mask coordinates bit 8" "0,1" bitfld.long 0x08 7. ",Mask coordinates bit 7" "0,1" bitfld.long 0x08 6. ",Mask coordinates bit 6" "0,1" bitfld.long 0x08 5. ",Mask coordinates bit 5" "0,1" bitfld.long 0x08 4. ",Mask coordinates bit 4" "0,1" bitfld.long 0x08 3. ",Mask coordinates bit 3" "0,1" bitfld.long 0x08 2. ",Mask coordinates bit 2" "0,1" bitfld.long 0x08 1. ",Mask coordinates bit 1" "0,1" bitfld.long 0x08 0. ",Mask coordinates bit 0" "0,1" line.long 0x0C "MASKHORIZONTALLOWERRIGHT,Mask Window Horizontal Coordinates Register" bitfld.long 0x0C 11. " MASKHORIZONTALLOWERRIGHT ,Mask coordinates bit 11" "0,1" bitfld.long 0x0C 10. ",Mask coordinates bit 10" "0,1" bitfld.long 0x0C 9. ",Mask coordinates bit 9" "0,1" bitfld.long 0x0C 8. ",Mask coordinates bit 8" "0,1" bitfld.long 0x0C 7. ",Mask coordinates bit 7" "0,1" bitfld.long 0x0C 6. ",Mask coordinates bit 6" "0,1" bitfld.long 0x0C 5. ",Mask coordinates bit 5" "0,1" bitfld.long 0x0C 4. ",Mask coordinates bit 4" "0,1" bitfld.long 0x0C 3. ",Mask coordinates bit 3" "0,1" bitfld.long 0x0C 2. ",Mask coordinates bit 2" "0,1" bitfld.long 0x0C 1. ",Mask coordinates bit 1" "0,1" bitfld.long 0x0C 0. ",Mask coordinates bit 0" "0,1" line.long 0x10 "MASKVERTICALUPPERLEFT,Mask Window Vertical Coordinates Register" bitfld.long 0x10 11. " MASKVERTICALUPPERLEFT ,Mask coordinates bit 11" "0,1" bitfld.long 0x10 10. ",Mask coordinates bit 10" "0,1" bitfld.long 0x10 9. ",Mask coordinates bit 9" "0,1" bitfld.long 0x10 8. ",Mask coordinates bit 8" "0,1" bitfld.long 0x10 7. ",Mask coordinates bit 7" "0,1" bitfld.long 0x10 6. ",Mask coordinates bit 6" "0,1" bitfld.long 0x10 5. ",Mask coordinates bit 5" "0,1" bitfld.long 0x10 4. ",Mask coordinates bit 4" "0,1" bitfld.long 0x10 3. ",Mask coordinates bit 3" "0,1" bitfld.long 0x10 2. ",Mask coordinates bit 2" "0,1" bitfld.long 0x10 1. ",Mask coordinates bit 1" "0,1" bitfld.long 0x10 0. ",Mask coordinates bit 0" "0,1" line.long 0x14 "MASKVERTICALLOWERRIGHT,Mask Window Vertical Coordinates Register" bitfld.long 0x14 11. " MASKVERTICALLOWERRIGHT ,Mask coordinates bit 11" "0,1" bitfld.long 0x14 10. ",Mask coordinates bit 10" "0,1" bitfld.long 0x14 9. ",Mask coordinates bit 9" "0,1" bitfld.long 0x14 8. ",Mask coordinates bit 8" "0,1" bitfld.long 0x14 7. ",Mask coordinates bit 7" "0,1" bitfld.long 0x14 6. ",Mask coordinates bit 6" "0,1" bitfld.long 0x14 5. ",Mask coordinates bit 5" "0,1" bitfld.long 0x14 4. ",Mask coordinates bit 4" "0,1" bitfld.long 0x14 3. ",Mask coordinates bit 3" "0,1" bitfld.long 0x14 2. ",Mask coordinates bit 2" "0,1" bitfld.long 0x14 1. ",Mask coordinates bit 1" "0,1" bitfld.long 0x14 0. ",Mask coordinates bit 0" "0,1" line.long 0x18 "HORIZONTALUPPERLEFTW0,Evaluation Window HorizontalUpperLeft Register" hexmask.long.word 0x18 0.--11. 1. " HORIZONTALUPPERLEFTW0 ,Evaluation window HorizontalUpperLeft" line.long 0x1C "HORIZONTALLOWERRIGHTW0,Evaluation Window HorizontalLowerRight Register" hexmask.long.word 0x1C 0.--11. 1. " HORIZONTALLOWERRIGHTW0 ,Evaluation window HorizontalLowerRight" line.long 0x20 "VERTICALUPPERLEFTW0,Evaluation Window VerticalUpperLeft Register" hexmask.long.word 0x20 0.--11. 1. " VERTICALUPPERLEFTW0 ,Evaluation window VerticalUpperLeft" line.long 0x24 "VERTICALLOWERRIGHTW0,Evaluation Window VerticalLowerRight Register" hexmask.long.word 0x24 0.--11. 1. " VERTICALLOWERRIGHTW0 ,Evaluation window VerticalLowerRight" line.long 0x28 "SIGNAREFERENCERW0,Signature A Reference Value Channel R Register" line.long 0x2C "SIGNAREFERENCEGW0,Signature A Reference Value Channel G Register" line.long 0x30 "SIGNAREFERENCEBW0,Signature A Reference Value Channel B Register" line.long 0x34 "SIGNBREFERENCERW0,Signature B Reference Value Channel R Register" line.long 0x38 "SIGNBREFERENCEGW0,Signature B Reference Value Channel G Register" line.long 0x3C "SIGNBREFERENCEBW0,Signature B Reference Value Channel B Register" line.long 0x40 "THRBRW0,Threshold Signature B Register" line.long 0x44 "THRBGW0,Threshold Signature B Register" line.long 0x48 "THRBBW0,Threshold Signature B Register" line.long 0x4C "ERRORTRESHOLD,Error Counter Threshold Register" hexmask.long.byte 0x4C 16.--23. 1. " ERRTHRESRESET ,Number of consecutive error free video frames" hexmask.long.byte 0x4C 0.--7. 1. " ERRTHRES ,Threshold of error counter" line.long 0x50 "CTRLCFGW0,Control/Configuration Register For Evaluation Window" bitfld.long 0x50 31. " INT_TYPE ,Type of interrupt generation 0" "Pulse,Level" bitfld.long 0x50 16. " ENCOORDW0 ,Enable coordinates for window 0" "Disabled,Enabled" textline " " bitfld.long 0x50 8. " ENSIGNB ,Enable for signature calculation B" "Disabled,Enabled" bitfld.long 0x50 0. " ENSIGNA ,Enable for signature calculation A" "Disabled,Enabled" line.long 0x54 "TRIGGERW0,Trigger Register" bitfld.long 0x54 8.--9. " TRIGMODE ,Trigger mode" "One generation,Cyclic generations,?..." bitfld.long 0x54 0. " TRIGGER ,Generate trigger for signature generation" "0,1" line.long 0x58 "IENW0,Interrupt Enable Register" bitfld.long 0x58 2. " IENRESVAL ,Interrupt enable" "Disabled,Enabled" bitfld.long 0x58 1. " IENCFGCOP ,Interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x58 0. " IENDIFF ,Interrupt enable" "Disabled,Enabled" line.long 0x5C "INTERRUPTSTATUSW0,Interrupt Status Register" eventfld.long 0x5C 2. " ISTSRESVAL ,Interrupt status flags" "No interrupt,Interrupt" eventfld.long 0x5C 1. " ISTSCFGCOP ,Interrupt status flags" "No interrupt,Interrupt" textline " " eventfld.long 0x5C 0. " ISTSDIFF ,Interrupt status flags" "No interrupt,Interrupt" rgroup.long 0x68++0x1F line.long 0x00 "STATUSW0,Status Register" bitfld.long 0x00 18. " DIFF_B_B ,Comparison of valid B result vs reference value" "Equal,Different" bitfld.long 0x00 17. " DIFF_B_G ,Comparison of valid G result vs reference value" "Equal,Different" textline " " bitfld.long 0x00 16. " DIFF_B_R ,Comparison of valid R result vs reference value" "Equal,Different" bitfld.long 0x00 10. " DIFF_A_B ,Comparison of valid B result vs reference value" "Equal,Different" textline " " bitfld.long 0x00 9. " DIFF_A_G ,Comparison of valid G result vs reference value" "Equal,Different" bitfld.long 0x00 8. " DIFF_A_R ,Comparison of valid R result vs reference value" "Equal,Different" textline " " bitfld.long 0x00 1. " ACTIVE ,Generation task is active" "Not active,Active" bitfld.long 0x00 0. " PENDING ,Generation task is pending" "Not pending,Pending" line.long 0x04 "SIGNATURE_ERROR,Signature Error Register" hexmask.long.word 0x04 0.--11. 1. " SIG_ERROR_COUNT ,The number of video frames with signature errors" line.long 0x08 "SIGNATUREARW0,Signature A Result Channel R Register" line.long 0x0C "SIGNATUREAGW0,Signature A Result Channel G Register" line.long 0x10 "SIGNATUREABW0,Signature A Result Channel B Register" line.long 0x14 "SIGNATUREBRW0,Signature B Result Channel R Register" line.long 0x18 "SIGNATUREBGW0,Signature B Result Channel G Register" line.long 0x1C "SIGNATUREBBW0,Signature B Result Channel B Register" width 0x0B tree.end tree "SIG 1" base ad:0x38210000 width 30. group.long 0x00++0x03 line.long 0x00 "LOCKUNLOCK,Lock/unlock Signature Unit Register" rgroup.long 0x04++0x03 line.long 0x00 "LOCKSTATUS,Lock Status Register" bitfld.long 0x00 0. " LOCKSTATUS ,Lock status" "Unlocked,Locked" group.long 0x08++0x5F line.long 0x00 "SWRESET,Software Reset Register" bitfld.long 0x00 0. " SWRES ,Software reset" "No reset,Reset" line.long 0x04 "CTRL,General Configuration Register" bitfld.long 0x04 16.--17. " SRCSEL ,Source select" "Source 0,Source 1,Source 2,Source 3" bitfld.long 0x04 8.--9. " VMASK_MODE ,Mask window handling (vertical coordinates)" "Not masked,Inside,Outside,?..." textline " " bitfld.long 0x04 0.--1. " HMASK_MODE ,Mask window handling (horizontal coordinates)" "Not masked,Inside,Outside,?..." line.long 0x08 "MASKHORIZONTALUPPERLEFT,Mask Window Horizontal Coordinates Register" bitfld.long 0x08 11. " MASKHORIZONTALUPPERLEFT ,Mask coordinates bit 11" "0,1" bitfld.long 0x08 10. ",Mask coordinates bit 10" "0,1" bitfld.long 0x08 9. ",Mask coordinates bit 9" "0,1" bitfld.long 0x08 8. ",Mask coordinates bit 8" "0,1" bitfld.long 0x08 7. ",Mask coordinates bit 7" "0,1" bitfld.long 0x08 6. ",Mask coordinates bit 6" "0,1" bitfld.long 0x08 5. ",Mask coordinates bit 5" "0,1" bitfld.long 0x08 4. ",Mask coordinates bit 4" "0,1" bitfld.long 0x08 3. ",Mask coordinates bit 3" "0,1" bitfld.long 0x08 2. ",Mask coordinates bit 2" "0,1" bitfld.long 0x08 1. ",Mask coordinates bit 1" "0,1" bitfld.long 0x08 0. ",Mask coordinates bit 0" "0,1" line.long 0x0C "MASKHORIZONTALLOWERRIGHT,Mask Window Horizontal Coordinates Register" bitfld.long 0x0C 11. " MASKHORIZONTALLOWERRIGHT ,Mask coordinates bit 11" "0,1" bitfld.long 0x0C 10. ",Mask coordinates bit 10" "0,1" bitfld.long 0x0C 9. ",Mask coordinates bit 9" "0,1" bitfld.long 0x0C 8. ",Mask coordinates bit 8" "0,1" bitfld.long 0x0C 7. ",Mask coordinates bit 7" "0,1" bitfld.long 0x0C 6. ",Mask coordinates bit 6" "0,1" bitfld.long 0x0C 5. ",Mask coordinates bit 5" "0,1" bitfld.long 0x0C 4. ",Mask coordinates bit 4" "0,1" bitfld.long 0x0C 3. ",Mask coordinates bit 3" "0,1" bitfld.long 0x0C 2. ",Mask coordinates bit 2" "0,1" bitfld.long 0x0C 1. ",Mask coordinates bit 1" "0,1" bitfld.long 0x0C 0. ",Mask coordinates bit 0" "0,1" line.long 0x10 "MASKVERTICALUPPERLEFT,Mask Window Vertical Coordinates Register" bitfld.long 0x10 11. " MASKVERTICALUPPERLEFT ,Mask coordinates bit 11" "0,1" bitfld.long 0x10 10. ",Mask coordinates bit 10" "0,1" bitfld.long 0x10 9. ",Mask coordinates bit 9" "0,1" bitfld.long 0x10 8. ",Mask coordinates bit 8" "0,1" bitfld.long 0x10 7. ",Mask coordinates bit 7" "0,1" bitfld.long 0x10 6. ",Mask coordinates bit 6" "0,1" bitfld.long 0x10 5. ",Mask coordinates bit 5" "0,1" bitfld.long 0x10 4. ",Mask coordinates bit 4" "0,1" bitfld.long 0x10 3. ",Mask coordinates bit 3" "0,1" bitfld.long 0x10 2. ",Mask coordinates bit 2" "0,1" bitfld.long 0x10 1. ",Mask coordinates bit 1" "0,1" bitfld.long 0x10 0. ",Mask coordinates bit 0" "0,1" line.long 0x14 "MASKVERTICALLOWERRIGHT,Mask Window Vertical Coordinates Register" bitfld.long 0x14 11. " MASKVERTICALLOWERRIGHT ,Mask coordinates bit 11" "0,1" bitfld.long 0x14 10. ",Mask coordinates bit 10" "0,1" bitfld.long 0x14 9. ",Mask coordinates bit 9" "0,1" bitfld.long 0x14 8. ",Mask coordinates bit 8" "0,1" bitfld.long 0x14 7. ",Mask coordinates bit 7" "0,1" bitfld.long 0x14 6. ",Mask coordinates bit 6" "0,1" bitfld.long 0x14 5. ",Mask coordinates bit 5" "0,1" bitfld.long 0x14 4. ",Mask coordinates bit 4" "0,1" bitfld.long 0x14 3. ",Mask coordinates bit 3" "0,1" bitfld.long 0x14 2. ",Mask coordinates bit 2" "0,1" bitfld.long 0x14 1. ",Mask coordinates bit 1" "0,1" bitfld.long 0x14 0. ",Mask coordinates bit 0" "0,1" line.long 0x18 "HORIZONTALUPPERLEFTW0,Evaluation Window HorizontalUpperLeft Register" hexmask.long.word 0x18 0.--11. 1. " HORIZONTALUPPERLEFTW0 ,Evaluation window HorizontalUpperLeft" line.long 0x1C "HORIZONTALLOWERRIGHTW0,Evaluation Window HorizontalLowerRight Register" hexmask.long.word 0x1C 0.--11. 1. " HORIZONTALLOWERRIGHTW0 ,Evaluation window HorizontalLowerRight" line.long 0x20 "VERTICALUPPERLEFTW0,Evaluation Window VerticalUpperLeft Register" hexmask.long.word 0x20 0.--11. 1. " VERTICALUPPERLEFTW0 ,Evaluation window VerticalUpperLeft" line.long 0x24 "VERTICALLOWERRIGHTW0,Evaluation Window VerticalLowerRight Register" hexmask.long.word 0x24 0.--11. 1. " VERTICALLOWERRIGHTW0 ,Evaluation window VerticalLowerRight" line.long 0x28 "SIGNAREFERENCERW0,Signature A Reference Value Channel R Register" line.long 0x2C "SIGNAREFERENCEGW0,Signature A Reference Value Channel G Register" line.long 0x30 "SIGNAREFERENCEBW0,Signature A Reference Value Channel B Register" line.long 0x34 "SIGNBREFERENCERW0,Signature B Reference Value Channel R Register" line.long 0x38 "SIGNBREFERENCEGW0,Signature B Reference Value Channel G Register" line.long 0x3C "SIGNBREFERENCEBW0,Signature B Reference Value Channel B Register" line.long 0x40 "THRBRW0,Threshold Signature B Register" line.long 0x44 "THRBGW0,Threshold Signature B Register" line.long 0x48 "THRBBW0,Threshold Signature B Register" line.long 0x4C "ERRORTRESHOLD,Error Counter Threshold Register" hexmask.long.byte 0x4C 16.--23. 1. " ERRTHRESRESET ,Number of consecutive error free video frames" hexmask.long.byte 0x4C 0.--7. 1. " ERRTHRES ,Threshold of error counter" line.long 0x50 "CTRLCFGW0,Control/Configuration Register For Evaluation Window" bitfld.long 0x50 31. " INT_TYPE ,Type of interrupt generation 0" "Pulse,Level" bitfld.long 0x50 16. " ENCOORDW0 ,Enable coordinates for window 0" "Disabled,Enabled" textline " " bitfld.long 0x50 8. " ENSIGNB ,Enable for signature calculation B" "Disabled,Enabled" bitfld.long 0x50 0. " ENSIGNA ,Enable for signature calculation A" "Disabled,Enabled" line.long 0x54 "TRIGGERW0,Trigger Register" bitfld.long 0x54 8.--9. " TRIGMODE ,Trigger mode" "One generation,Cyclic generations,?..." bitfld.long 0x54 0. " TRIGGER ,Generate trigger for signature generation" "0,1" line.long 0x58 "IENW0,Interrupt Enable Register" bitfld.long 0x58 2. " IENRESVAL ,Interrupt enable" "Disabled,Enabled" bitfld.long 0x58 1. " IENCFGCOP ,Interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x58 0. " IENDIFF ,Interrupt enable" "Disabled,Enabled" line.long 0x5C "INTERRUPTSTATUSW0,Interrupt Status Register" eventfld.long 0x5C 2. " ISTSRESVAL ,Interrupt status flags" "No interrupt,Interrupt" eventfld.long 0x5C 1. " ISTSCFGCOP ,Interrupt status flags" "No interrupt,Interrupt" textline " " eventfld.long 0x5C 0. " ISTSDIFF ,Interrupt status flags" "No interrupt,Interrupt" rgroup.long 0x68++0x1F line.long 0x00 "STATUSW0,Status Register" bitfld.long 0x00 18. " DIFF_B_B ,Comparison of valid B result vs reference value" "Equal,Different" bitfld.long 0x00 17. " DIFF_B_G ,Comparison of valid G result vs reference value" "Equal,Different" textline " " bitfld.long 0x00 16. " DIFF_B_R ,Comparison of valid R result vs reference value" "Equal,Different" bitfld.long 0x00 10. " DIFF_A_B ,Comparison of valid B result vs reference value" "Equal,Different" textline " " bitfld.long 0x00 9. " DIFF_A_G ,Comparison of valid G result vs reference value" "Equal,Different" bitfld.long 0x00 8. " DIFF_A_R ,Comparison of valid R result vs reference value" "Equal,Different" textline " " bitfld.long 0x00 1. " ACTIVE ,Generation task is active" "Not active,Active" bitfld.long 0x00 0. " PENDING ,Generation task is pending" "Not pending,Pending" line.long 0x04 "SIGNATURE_ERROR,Signature Error Register" hexmask.long.word 0x04 0.--11. 1. " SIG_ERROR_COUNT ,The number of video frames with signature errors" line.long 0x08 "SIGNATUREARW0,Signature A Result Channel R Register" line.long 0x0C "SIGNATUREAGW0,Signature A Result Channel G Register" line.long 0x10 "SIGNATUREABW0,Signature A Result Channel B Register" line.long 0x14 "SIGNATUREBRW0,Signature B Result Channel R Register" line.long 0x18 "SIGNATUREBGW0,Signature B Result Channel G Register" line.long 0x1C "SIGNATUREBBW0,Signature B Result Channel B Register" width 0x0B tree.end tree "SIG 2" base ad:0x38220000 width 30. group.long 0x00++0x03 line.long 0x00 "LOCKUNLOCK,Lock/unlock Signature Unit Register" rgroup.long 0x04++0x03 line.long 0x00 "LOCKSTATUS,Lock Status Register" bitfld.long 0x00 0. " LOCKSTATUS ,Lock status" "Unlocked,Locked" group.long 0x08++0x5F line.long 0x00 "SWRESET,Software Reset Register" bitfld.long 0x00 0. " SWRES ,Software reset" "No reset,Reset" line.long 0x04 "CTRL,General Configuration Register" bitfld.long 0x04 16.--17. " SRCSEL ,Source select" "Source 0,Source 1,Source 2,Source 3" bitfld.long 0x04 8.--9. " VMASK_MODE ,Mask window handling (vertical coordinates)" "Not masked,Inside,Outside,?..." textline " " bitfld.long 0x04 0.--1. " HMASK_MODE ,Mask window handling (horizontal coordinates)" "Not masked,Inside,Outside,?..." line.long 0x08 "MASKHORIZONTALUPPERLEFT,Mask Window Horizontal Coordinates Register" bitfld.long 0x08 11. " MASKHORIZONTALUPPERLEFT ,Mask coordinates bit 11" "0,1" bitfld.long 0x08 10. ",Mask coordinates bit 10" "0,1" bitfld.long 0x08 9. ",Mask coordinates bit 9" "0,1" bitfld.long 0x08 8. ",Mask coordinates bit 8" "0,1" bitfld.long 0x08 7. ",Mask coordinates bit 7" "0,1" bitfld.long 0x08 6. ",Mask coordinates bit 6" "0,1" bitfld.long 0x08 5. ",Mask coordinates bit 5" "0,1" bitfld.long 0x08 4. ",Mask coordinates bit 4" "0,1" bitfld.long 0x08 3. ",Mask coordinates bit 3" "0,1" bitfld.long 0x08 2. ",Mask coordinates bit 2" "0,1" bitfld.long 0x08 1. ",Mask coordinates bit 1" "0,1" bitfld.long 0x08 0. ",Mask coordinates bit 0" "0,1" line.long 0x0C "MASKHORIZONTALLOWERRIGHT,Mask Window Horizontal Coordinates Register" bitfld.long 0x0C 11. " MASKHORIZONTALLOWERRIGHT ,Mask coordinates bit 11" "0,1" bitfld.long 0x0C 10. ",Mask coordinates bit 10" "0,1" bitfld.long 0x0C 9. ",Mask coordinates bit 9" "0,1" bitfld.long 0x0C 8. ",Mask coordinates bit 8" "0,1" bitfld.long 0x0C 7. ",Mask coordinates bit 7" "0,1" bitfld.long 0x0C 6. ",Mask coordinates bit 6" "0,1" bitfld.long 0x0C 5. ",Mask coordinates bit 5" "0,1" bitfld.long 0x0C 4. ",Mask coordinates bit 4" "0,1" bitfld.long 0x0C 3. ",Mask coordinates bit 3" "0,1" bitfld.long 0x0C 2. ",Mask coordinates bit 2" "0,1" bitfld.long 0x0C 1. ",Mask coordinates bit 1" "0,1" bitfld.long 0x0C 0. ",Mask coordinates bit 0" "0,1" line.long 0x10 "MASKVERTICALUPPERLEFT,Mask Window Vertical Coordinates Register" bitfld.long 0x10 11. " MASKVERTICALUPPERLEFT ,Mask coordinates bit 11" "0,1" bitfld.long 0x10 10. ",Mask coordinates bit 10" "0,1" bitfld.long 0x10 9. ",Mask coordinates bit 9" "0,1" bitfld.long 0x10 8. ",Mask coordinates bit 8" "0,1" bitfld.long 0x10 7. ",Mask coordinates bit 7" "0,1" bitfld.long 0x10 6. ",Mask coordinates bit 6" "0,1" bitfld.long 0x10 5. ",Mask coordinates bit 5" "0,1" bitfld.long 0x10 4. ",Mask coordinates bit 4" "0,1" bitfld.long 0x10 3. ",Mask coordinates bit 3" "0,1" bitfld.long 0x10 2. ",Mask coordinates bit 2" "0,1" bitfld.long 0x10 1. ",Mask coordinates bit 1" "0,1" bitfld.long 0x10 0. ",Mask coordinates bit 0" "0,1" line.long 0x14 "MASKVERTICALLOWERRIGHT,Mask Window Vertical Coordinates Register" bitfld.long 0x14 11. " MASKVERTICALLOWERRIGHT ,Mask coordinates bit 11" "0,1" bitfld.long 0x14 10. ",Mask coordinates bit 10" "0,1" bitfld.long 0x14 9. ",Mask coordinates bit 9" "0,1" bitfld.long 0x14 8. ",Mask coordinates bit 8" "0,1" bitfld.long 0x14 7. ",Mask coordinates bit 7" "0,1" bitfld.long 0x14 6. ",Mask coordinates bit 6" "0,1" bitfld.long 0x14 5. ",Mask coordinates bit 5" "0,1" bitfld.long 0x14 4. ",Mask coordinates bit 4" "0,1" bitfld.long 0x14 3. ",Mask coordinates bit 3" "0,1" bitfld.long 0x14 2. ",Mask coordinates bit 2" "0,1" bitfld.long 0x14 1. ",Mask coordinates bit 1" "0,1" bitfld.long 0x14 0. ",Mask coordinates bit 0" "0,1" line.long 0x18 "HORIZONTALUPPERLEFTW0,Evaluation Window HorizontalUpperLeft Register" hexmask.long.word 0x18 0.--11. 1. " HORIZONTALUPPERLEFTW0 ,Evaluation window HorizontalUpperLeft" line.long 0x1C "HORIZONTALLOWERRIGHTW0,Evaluation Window HorizontalLowerRight Register" hexmask.long.word 0x1C 0.--11. 1. " HORIZONTALLOWERRIGHTW0 ,Evaluation window HorizontalLowerRight" line.long 0x20 "VERTICALUPPERLEFTW0,Evaluation Window VerticalUpperLeft Register" hexmask.long.word 0x20 0.--11. 1. " VERTICALUPPERLEFTW0 ,Evaluation window VerticalUpperLeft" line.long 0x24 "VERTICALLOWERRIGHTW0,Evaluation Window VerticalLowerRight Register" hexmask.long.word 0x24 0.--11. 1. " VERTICALLOWERRIGHTW0 ,Evaluation window VerticalLowerRight" line.long 0x28 "SIGNAREFERENCERW0,Signature A Reference Value Channel R Register" line.long 0x2C "SIGNAREFERENCEGW0,Signature A Reference Value Channel G Register" line.long 0x30 "SIGNAREFERENCEBW0,Signature A Reference Value Channel B Register" line.long 0x34 "SIGNBREFERENCERW0,Signature B Reference Value Channel R Register" line.long 0x38 "SIGNBREFERENCEGW0,Signature B Reference Value Channel G Register" line.long 0x3C "SIGNBREFERENCEBW0,Signature B Reference Value Channel B Register" line.long 0x40 "THRBRW0,Threshold Signature B Register" line.long 0x44 "THRBGW0,Threshold Signature B Register" line.long 0x48 "THRBBW0,Threshold Signature B Register" line.long 0x4C "ERRORTRESHOLD,Error Counter Threshold Register" hexmask.long.byte 0x4C 16.--23. 1. " ERRTHRESRESET ,Number of consecutive error free video frames" hexmask.long.byte 0x4C 0.--7. 1. " ERRTHRES ,Threshold of error counter" line.long 0x50 "CTRLCFGW0,Control/Configuration Register For Evaluation Window" bitfld.long 0x50 31. " INT_TYPE ,Type of interrupt generation 0" "Pulse,Level" bitfld.long 0x50 16. " ENCOORDW0 ,Enable coordinates for window 0" "Disabled,Enabled" textline " " bitfld.long 0x50 8. " ENSIGNB ,Enable for signature calculation B" "Disabled,Enabled" bitfld.long 0x50 0. " ENSIGNA ,Enable for signature calculation A" "Disabled,Enabled" line.long 0x54 "TRIGGERW0,Trigger Register" bitfld.long 0x54 8.--9. " TRIGMODE ,Trigger mode" "One generation,Cyclic generations,?..." bitfld.long 0x54 0. " TRIGGER ,Generate trigger for signature generation" "0,1" line.long 0x58 "IENW0,Interrupt Enable Register" bitfld.long 0x58 2. " IENRESVAL ,Interrupt enable" "Disabled,Enabled" bitfld.long 0x58 1. " IENCFGCOP ,Interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x58 0. " IENDIFF ,Interrupt enable" "Disabled,Enabled" line.long 0x5C "INTERRUPTSTATUSW0,Interrupt Status Register" eventfld.long 0x5C 2. " ISTSRESVAL ,Interrupt status flags" "No interrupt,Interrupt" eventfld.long 0x5C 1. " ISTSCFGCOP ,Interrupt status flags" "No interrupt,Interrupt" textline " " eventfld.long 0x5C 0. " ISTSDIFF ,Interrupt status flags" "No interrupt,Interrupt" rgroup.long 0x68++0x1F line.long 0x00 "STATUSW0,Status Register" bitfld.long 0x00 18. " DIFF_B_B ,Comparison of valid B result vs reference value" "Equal,Different" bitfld.long 0x00 17. " DIFF_B_G ,Comparison of valid G result vs reference value" "Equal,Different" textline " " bitfld.long 0x00 16. " DIFF_B_R ,Comparison of valid R result vs reference value" "Equal,Different" bitfld.long 0x00 10. " DIFF_A_B ,Comparison of valid B result vs reference value" "Equal,Different" textline " " bitfld.long 0x00 9. " DIFF_A_G ,Comparison of valid G result vs reference value" "Equal,Different" bitfld.long 0x00 8. " DIFF_A_R ,Comparison of valid R result vs reference value" "Equal,Different" textline " " bitfld.long 0x00 1. " ACTIVE ,Generation task is active" "Not active,Active" bitfld.long 0x00 0. " PENDING ,Generation task is pending" "Not pending,Pending" line.long 0x04 "SIGNATURE_ERROR,Signature Error Register" hexmask.long.word 0x04 0.--11. 1. " SIG_ERROR_COUNT ,The number of video frames with signature errors" line.long 0x08 "SIGNATUREARW0,Signature A Result Channel R Register" line.long 0x0C "SIGNATUREAGW0,Signature A Result Channel G Register" line.long 0x10 "SIGNATUREABW0,Signature A Result Channel B Register" line.long 0x14 "SIGNATUREBRW0,Signature B Result Channel R Register" line.long 0x18 "SIGNATUREBGW0,Signature B Result Channel G Register" line.long 0x1C "SIGNATUREBBW0,Signature B Result Channel B Register" width 0x0B tree.end tree.end tree "Ethernet Link Controller" base ad:0x38220000 width 8. group.long 0x00++0x1F line.long 0x00 "MCR,MAC Configuration Register" sif (cpu()=="MB86R12") bitfld.long 0x00 25. " CST ,CRC stripping for Type frames" "0,1" textline " " endif bitfld.long 0x00 24. " TC ,Transmit Configuration in RGMII" "Not set,Set" bitfld.long 0x00 23. " WD ,Watchdog disable" "No,Yes" textline " " bitfld.long 0x00 22. " JD ,Jabber disable" "No,Yes" bitfld.long 0x00 21. " BE ,Frame burst enable" "Disabled,Enabled" bitfld.long 0x00 20. " JE ,Jumbo frame enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17.--19. " IFG ,Inter-Frame GAP" "96 bit times,88 bit times,80 bit times,72 bit times,64 bit times,56 bit times,48 bit times,40 bit times" bitfld.long 0x00 16. " DCRS ,Disable Carrier Sense During Transaction" "No,Yes" bitfld.long 0x00 15. " PS ,Port select" "GMII,MII" textline " " bitfld.long 0x00 14. " FES ,Speed" "10 Mbps,100 Mbps" bitfld.long 0x00 13. " DO ,Disable receive own" "No,Yes" bitfld.long 0x00 12. " LM ,Loop-back mode" "No mode,Mode" textline " " bitfld.long 0x00 11. " DM ,Duplex mode" "No mode,Mode" bitfld.long 0x00 10. " IPC ,Checksum Offload" "Disabled,Enabled" bitfld.long 0x00 9. " DR ,Disable retry" "No,Yes" textline " " bitfld.long 0x00 8. " LUD ,Link Up/Down" "Link Down,Link Up" bitfld.long 0x00 7. " ACS ,Automatic CRC stripping" "Disabled,Enabled" bitfld.long 0x00 5.--6. " BL ,Back-off limit" "k = min (n 10),k = min (n 8),k = min (n 4),k = min (n 1)" textline " " bitfld.long 0x00 4. " DC ,Deferral check" "Not checked,Checked" bitfld.long 0x00 3. " TE ,Transmitter enable" "Disabled,Enabled" bitfld.long 0x00 2. " RE ,Receiver enable" "Disabled,Enabled" line.long 0x04 "MFFR,MAC Frame Filter Register" bitfld.long 0x04 31. " RA ,Receive all" "Not received,Received" bitfld.long 0x04 10. " HPF ,Hash or Perfect Filter" "Not set,Set" bitfld.long 0x04 9. " SAF ,Source Address Filter" "Off,On" textline " " bitfld.long 0x04 8. " SAIF ,Source Address Inverse Filter" "Marked as failing,Inverse mode" bitfld.long 0x04 6.--7. " PCF ,Pass control frames" "Not passed,Passed except PAUSE,Passed even Fail Address Filter,Passed" textline " " bitfld.long 0x04 5. " DB ,Disable broadcast frames" "No,Yes" bitfld.long 0x04 4. " PM ,Pass all multicast" "Not passed,Passed" bitfld.long 0x04 3. " DAIF ,DA Inverse Filtering" "Normal filtering,Inverse filtering" textline " " bitfld.long 0x04 2. " HMC ,Hash Multicast" "Perfect,Hash" bitfld.long 0x04 1. " HUC ,Hash Unicast" "Perfect,Hash" bitfld.long 0x04 0. " PR ,Promiscuous mode" "No mode,Mode" line.long 0x08 "MHTRH,MAC Hash Table Register(High)" line.long 0x0C "MHTRL,MAC Hash Table Register(Low)" line.long 0x10 "GAR,GMII Adress Register" bitfld.long 0x10 11.--15. " PA ,Physical layer address" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x10 6.--10. " GR ,GMII/MII register" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x10 2.--5. " CR ,Application clock range" "60-100MHz AHBCLK/42,100-150MHz AHBCLK/62,20-35MHz AHBCLK/16,35-60MHz AHBCLK/26,150-250MHz AHBCLK/102,250-300MHz AHBCLK/122,,,AHBCLK/4,AHBCLK/6,AHBCLK/8,AHBCLK/10,AHBCLK/12,AHBCLK/14,AHBCLK/16,AHBCLK/18" textline " " bitfld.long 0x10 1. " GW ,GMII/MII write" "Disabled,Enabled" bitfld.long 0x10 0. " GB ,GMII/MII busy" "Not busy,Busy" line.long 0x14 "GDR,GMII Data Register" hexmask.long.word 0x14 0.--15. 1. " GD ,GMII/MII data register" line.long 0x18 "FCR,Flow Control Register" hexmask.long.word 0x18 16.--31. 1. " PT ,Pause time" bitfld.long 0x18 7. " DZPQ ,Disable Zero-Quanta Pause" "No,Yes" bitfld.long 0x18 4.--5. " PLT ,Pause Low Threshold" "4slot times,28slot times,144slot times,256slot times" textline " " bitfld.long 0x18 3. " UP ,Unicast pause frame detect" "Disabled,Enabled" bitfld.long 0x18 2. " RFE ,Receive flow control enable" "Disabled,Enabled" bitfld.long 0x18 1. " TFE ,Receive flow enable" "Disabled,Enabled" textline " " bitfld.long 0x18 0. " FCB ,Flow control busy" "Not busy,Busy" line.long 0x1C "VTR,VLAN Tag Register" bitfld.long 0x1C 16. " ETV ,Enable 12-Bit VLAN Tag Comparison" "Disabled,Enabled" hexmask.long.word 0x1C 0.--15. 1. " VL ,VLAN tag identifier" group.long 0x28++0x3 line.long 0x00 "RWFFR,Remote Wake-Up Frame Filter Register" hgroup.long 0x2C++0x7 hide.long 0x00 "PMTR,PMT Register" in hide.long 0x04 "LPICSR,GMAC Regiter 12" in group.long 0x34++0x03 line.long 0x00 "LPITCR,LPI Timers Control Register" hexmask.long.word 0x00 16.--25. 1. " LIT ,LPI LS TIMER" hexmask.long.word 0x00 0.--15. 1. " TWT ,LPI TW TIMER" rgroup.long 0x38++0x03 line.long 0x00 "ISR,Interrupt Status Register" bitfld.long 0x00 10. " LPIIS ,LPI Interrupt Status" "0,1" bitfld.long 0x00 7. " COIS ,MMC Receive Checksum Offload Interrupt Status" "0,1" textline " " bitfld.long 0x00 6. " TIS ,MMC Transmit Interrupt Status" "0,1" bitfld.long 0x00 5. " RIS ,MMC Recieve Interrupt Status" "0,1" bitfld.long 0x00 4. " MIS ,MMC Interrupt Status" "0,1" textline " " bitfld.long 0x00 3. " PIS ,PMT Interrupt Status" "0,1" bitfld.long 0x00 0. " RGIS ,RGMII Interrupt Status" "0,1" group.long 0x3C++0x03 line.long 0x00 "IMR,Interrupt Mask Register" bitfld.long 0x00 10. " LPIIM ,LPI Interrupt Mask" "Not masked,Masked" bitfld.long 0x00 3. " PIM ,PMT Interrupt Mask" "Not masked,Masked" textline " " bitfld.long 0x00 0. " RGIM ,RGMII Interrupt Mask" "Not masked,Masked" group.long 0x40++0x7 line.long 0x00 "MAR0H,MAC Address0 Register(High)" rbitfld.long 0x00 31. " MO ,Must be One" ",1" hexmask.long.word 0x00 0.--15. 1. " A_0_47_32 ,MAC Address 0 [47:32]" line.long 0x04 "MAR0L,MAC Address0 Register(Low) [31:0]" if (1.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x0)++0x07 line.long 0x00 "MAR1H,MAC Address1 Register(High)" bitfld.long 0x00 31. " AE_1 ,Address1 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_1_47_32 ,MAC address1 [47:32]" line.long 0x04 "MAR1L,MAC Address1 Register(Low) [31:0]" else group.long (0x48+0x0)++0x07 line.long 0x00 "MAR1H,MAC Address1 Register(High)" bitfld.long 0x00 31. " AE_1 ,Address1 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_1_47_32 ,MAC address1 [47:32]" line.long 0x04 "MAR1L,MAC Address1 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x0)++0x07 line.long 0x00 "MAR1H,MAC Address1 Register(High)" bitfld.long 0x00 31. " AE_1 ,Address1 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_1_47_32 ,MAC address1 [47:32]" line.long 0x04 "MAR1L,MAC Address1 Register(Low) [31:0]" else group.long (0x48+0x0)++0x07 line.long 0x00 "MAR1H,MAC Address1 Register(High)" bitfld.long 0x00 31. " AE_1 ,Address1 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_1_47_32 ,MAC address1 [47:32]" line.long 0x04 "MAR1L,MAC Address1 Register(Low) [31:0]" endif endif if (2.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x8)++0x07 line.long 0x00 "MAR2H,MAC Address2 Register(High)" bitfld.long 0x00 31. " AE_2 ,Address2 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_2_47_32 ,MAC address2 [47:32]" line.long 0x04 "MAR2L,MAC Address2 Register(Low) [31:0]" else group.long (0x48+0x8)++0x07 line.long 0x00 "MAR2H,MAC Address2 Register(High)" bitfld.long 0x00 31. " AE_2 ,Address2 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_2_47_32 ,MAC address2 [47:32]" line.long 0x04 "MAR2L,MAC Address2 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x8)++0x07 line.long 0x00 "MAR2H,MAC Address2 Register(High)" bitfld.long 0x00 31. " AE_2 ,Address2 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_2_47_32 ,MAC address2 [47:32]" line.long 0x04 "MAR2L,MAC Address2 Register(Low) [31:0]" else group.long (0x48+0x8)++0x07 line.long 0x00 "MAR2H,MAC Address2 Register(High)" bitfld.long 0x00 31. " AE_2 ,Address2 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_2_47_32 ,MAC address2 [47:32]" line.long 0x04 "MAR2L,MAC Address2 Register(Low) [31:0]" endif endif if (3.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x10)++0x07 line.long 0x00 "MAR3H,MAC Address3 Register(High)" bitfld.long 0x00 31. " AE_3 ,Address3 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_3_47_32 ,MAC address3 [47:32]" line.long 0x04 "MAR3L,MAC Address3 Register(Low) [31:0]" else group.long (0x48+0x10)++0x07 line.long 0x00 "MAR3H,MAC Address3 Register(High)" bitfld.long 0x00 31. " AE_3 ,Address3 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_3_47_32 ,MAC address3 [47:32]" line.long 0x04 "MAR3L,MAC Address3 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x10)++0x07 line.long 0x00 "MAR3H,MAC Address3 Register(High)" bitfld.long 0x00 31. " AE_3 ,Address3 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_3_47_32 ,MAC address3 [47:32]" line.long 0x04 "MAR3L,MAC Address3 Register(Low) [31:0]" else group.long (0x48+0x10)++0x07 line.long 0x00 "MAR3H,MAC Address3 Register(High)" bitfld.long 0x00 31. " AE_3 ,Address3 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_3_47_32 ,MAC address3 [47:32]" line.long 0x04 "MAR3L,MAC Address3 Register(Low) [31:0]" endif endif if (4.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x18)++0x07 line.long 0x00 "MAR4H,MAC Address4 Register(High)" bitfld.long 0x00 31. " AE_4 ,Address4 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_4_47_32 ,MAC address4 [47:32]" line.long 0x04 "MAR4L,MAC Address4 Register(Low) [31:0]" else group.long (0x48+0x18)++0x07 line.long 0x00 "MAR4H,MAC Address4 Register(High)" bitfld.long 0x00 31. " AE_4 ,Address4 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_4_47_32 ,MAC address4 [47:32]" line.long 0x04 "MAR4L,MAC Address4 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x18)++0x07 line.long 0x00 "MAR4H,MAC Address4 Register(High)" bitfld.long 0x00 31. " AE_4 ,Address4 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_4_47_32 ,MAC address4 [47:32]" line.long 0x04 "MAR4L,MAC Address4 Register(Low) [31:0]" else group.long (0x48+0x18)++0x07 line.long 0x00 "MAR4H,MAC Address4 Register(High)" bitfld.long 0x00 31. " AE_4 ,Address4 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_4_47_32 ,MAC address4 [47:32]" line.long 0x04 "MAR4L,MAC Address4 Register(Low) [31:0]" endif endif if (5.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x20)++0x07 line.long 0x00 "MAR5H,MAC Address5 Register(High)" bitfld.long 0x00 31. " AE_5 ,Address5 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_5_47_32 ,MAC address5 [47:32]" line.long 0x04 "MAR5L,MAC Address5 Register(Low) [31:0]" else group.long (0x48+0x20)++0x07 line.long 0x00 "MAR5H,MAC Address5 Register(High)" bitfld.long 0x00 31. " AE_5 ,Address5 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_5_47_32 ,MAC address5 [47:32]" line.long 0x04 "MAR5L,MAC Address5 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x20)++0x07 line.long 0x00 "MAR5H,MAC Address5 Register(High)" bitfld.long 0x00 31. " AE_5 ,Address5 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_5_47_32 ,MAC address5 [47:32]" line.long 0x04 "MAR5L,MAC Address5 Register(Low) [31:0]" else group.long (0x48+0x20)++0x07 line.long 0x00 "MAR5H,MAC Address5 Register(High)" bitfld.long 0x00 31. " AE_5 ,Address5 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_5_47_32 ,MAC address5 [47:32]" line.long 0x04 "MAR5L,MAC Address5 Register(Low) [31:0]" endif endif if (6.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x28)++0x07 line.long 0x00 "MAR6H,MAC Address6 Register(High)" bitfld.long 0x00 31. " AE_6 ,Address6 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_6_47_32 ,MAC address6 [47:32]" line.long 0x04 "MAR6L,MAC Address6 Register(Low) [31:0]" else group.long (0x48+0x28)++0x07 line.long 0x00 "MAR6H,MAC Address6 Register(High)" bitfld.long 0x00 31. " AE_6 ,Address6 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_6_47_32 ,MAC address6 [47:32]" line.long 0x04 "MAR6L,MAC Address6 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x28)++0x07 line.long 0x00 "MAR6H,MAC Address6 Register(High)" bitfld.long 0x00 31. " AE_6 ,Address6 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_6_47_32 ,MAC address6 [47:32]" line.long 0x04 "MAR6L,MAC Address6 Register(Low) [31:0]" else group.long (0x48+0x28)++0x07 line.long 0x00 "MAR6H,MAC Address6 Register(High)" bitfld.long 0x00 31. " AE_6 ,Address6 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_6_47_32 ,MAC address6 [47:32]" line.long 0x04 "MAR6L,MAC Address6 Register(Low) [31:0]" endif endif if (7.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x30)++0x07 line.long 0x00 "MAR7H,MAC Address7 Register(High)" bitfld.long 0x00 31. " AE_7 ,Address7 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_7_47_32 ,MAC address7 [47:32]" line.long 0x04 "MAR7L,MAC Address7 Register(Low) [31:0]" else group.long (0x48+0x30)++0x07 line.long 0x00 "MAR7H,MAC Address7 Register(High)" bitfld.long 0x00 31. " AE_7 ,Address7 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_7_47_32 ,MAC address7 [47:32]" line.long 0x04 "MAR7L,MAC Address7 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x30)++0x07 line.long 0x00 "MAR7H,MAC Address7 Register(High)" bitfld.long 0x00 31. " AE_7 ,Address7 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_7_47_32 ,MAC address7 [47:32]" line.long 0x04 "MAR7L,MAC Address7 Register(Low) [31:0]" else group.long (0x48+0x30)++0x07 line.long 0x00 "MAR7H,MAC Address7 Register(High)" bitfld.long 0x00 31. " AE_7 ,Address7 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_7_47_32 ,MAC address7 [47:32]" line.long 0x04 "MAR7L,MAC Address7 Register(Low) [31:0]" endif endif if (8.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x38)++0x07 line.long 0x00 "MAR8H,MAC Address8 Register(High)" bitfld.long 0x00 31. " AE_8 ,Address8 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_8_47_32 ,MAC address8 [47:32]" line.long 0x04 "MAR8L,MAC Address8 Register(Low) [31:0]" else group.long (0x48+0x38)++0x07 line.long 0x00 "MAR8H,MAC Address8 Register(High)" bitfld.long 0x00 31. " AE_8 ,Address8 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_8_47_32 ,MAC address8 [47:32]" line.long 0x04 "MAR8L,MAC Address8 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x38)++0x07 line.long 0x00 "MAR8H,MAC Address8 Register(High)" bitfld.long 0x00 31. " AE_8 ,Address8 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_8_47_32 ,MAC address8 [47:32]" line.long 0x04 "MAR8L,MAC Address8 Register(Low) [31:0]" else group.long (0x48+0x38)++0x07 line.long 0x00 "MAR8H,MAC Address8 Register(High)" bitfld.long 0x00 31. " AE_8 ,Address8 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_8_47_32 ,MAC address8 [47:32]" line.long 0x04 "MAR8L,MAC Address8 Register(Low) [31:0]" endif endif if (9.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x40)++0x07 line.long 0x00 "MAR9H,MAC Address9 Register(High)" bitfld.long 0x00 31. " AE_9 ,Address9 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_9_47_32 ,MAC address9 [47:32]" line.long 0x04 "MAR9L,MAC Address9 Register(Low) [31:0]" else group.long (0x48+0x40)++0x07 line.long 0x00 "MAR9H,MAC Address9 Register(High)" bitfld.long 0x00 31. " AE_9 ,Address9 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_9_47_32 ,MAC address9 [47:32]" line.long 0x04 "MAR9L,MAC Address9 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x40)++0x07 line.long 0x00 "MAR9H,MAC Address9 Register(High)" bitfld.long 0x00 31. " AE_9 ,Address9 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_9_47_32 ,MAC address9 [47:32]" line.long 0x04 "MAR9L,MAC Address9 Register(Low) [31:0]" else group.long (0x48+0x40)++0x07 line.long 0x00 "MAR9H,MAC Address9 Register(High)" bitfld.long 0x00 31. " AE_9 ,Address9 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_9_47_32 ,MAC address9 [47:32]" line.long 0x04 "MAR9L,MAC Address9 Register(Low) [31:0]" endif endif if (10.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x48)++0x07 line.long 0x00 "MAR10H,MAC Address10 Register(High)" bitfld.long 0x00 31. " AE_10 ,Address10 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_10_47_32 ,MAC address10 [47:32]" line.long 0x04 "MAR10L,MAC Address10 Register(Low) [31:0]" else group.long (0x48+0x48)++0x07 line.long 0x00 "MAR10H,MAC Address10 Register(High)" bitfld.long 0x00 31. " AE_10 ,Address10 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_10_47_32 ,MAC address10 [47:32]" line.long 0x04 "MAR10L,MAC Address10 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x48)++0x07 line.long 0x00 "MAR10H,MAC Address10 Register(High)" bitfld.long 0x00 31. " AE_10 ,Address10 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_10_47_32 ,MAC address10 [47:32]" line.long 0x04 "MAR10L,MAC Address10 Register(Low) [31:0]" else group.long (0x48+0x48)++0x07 line.long 0x00 "MAR10H,MAC Address10 Register(High)" bitfld.long 0x00 31. " AE_10 ,Address10 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_10_47_32 ,MAC address10 [47:32]" line.long 0x04 "MAR10L,MAC Address10 Register(Low) [31:0]" endif endif if (11.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x50)++0x07 line.long 0x00 "MAR11H,MAC Address11 Register(High)" bitfld.long 0x00 31. " AE_11 ,Address11 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_11_47_32 ,MAC address11 [47:32]" line.long 0x04 "MAR11L,MAC Address11 Register(Low) [31:0]" else group.long (0x48+0x50)++0x07 line.long 0x00 "MAR11H,MAC Address11 Register(High)" bitfld.long 0x00 31. " AE_11 ,Address11 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_11_47_32 ,MAC address11 [47:32]" line.long 0x04 "MAR11L,MAC Address11 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x50)++0x07 line.long 0x00 "MAR11H,MAC Address11 Register(High)" bitfld.long 0x00 31. " AE_11 ,Address11 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_11_47_32 ,MAC address11 [47:32]" line.long 0x04 "MAR11L,MAC Address11 Register(Low) [31:0]" else group.long (0x48+0x50)++0x07 line.long 0x00 "MAR11H,MAC Address11 Register(High)" bitfld.long 0x00 31. " AE_11 ,Address11 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_11_47_32 ,MAC address11 [47:32]" line.long 0x04 "MAR11L,MAC Address11 Register(Low) [31:0]" endif endif if (12.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x58)++0x07 line.long 0x00 "MAR12H,MAC Address12 Register(High)" bitfld.long 0x00 31. " AE_12 ,Address12 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_12_47_32 ,MAC address12 [47:32]" line.long 0x04 "MAR12L,MAC Address12 Register(Low) [31:0]" else group.long (0x48+0x58)++0x07 line.long 0x00 "MAR12H,MAC Address12 Register(High)" bitfld.long 0x00 31. " AE_12 ,Address12 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_12_47_32 ,MAC address12 [47:32]" line.long 0x04 "MAR12L,MAC Address12 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x58)++0x07 line.long 0x00 "MAR12H,MAC Address12 Register(High)" bitfld.long 0x00 31. " AE_12 ,Address12 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_12_47_32 ,MAC address12 [47:32]" line.long 0x04 "MAR12L,MAC Address12 Register(Low) [31:0]" else group.long (0x48+0x58)++0x07 line.long 0x00 "MAR12H,MAC Address12 Register(High)" bitfld.long 0x00 31. " AE_12 ,Address12 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_12_47_32 ,MAC address12 [47:32]" line.long 0x04 "MAR12L,MAC Address12 Register(Low) [31:0]" endif endif if (13.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x60)++0x07 line.long 0x00 "MAR13H,MAC Address13 Register(High)" bitfld.long 0x00 31. " AE_13 ,Address13 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_13_47_32 ,MAC address13 [47:32]" line.long 0x04 "MAR13L,MAC Address13 Register(Low) [31:0]" else group.long (0x48+0x60)++0x07 line.long 0x00 "MAR13H,MAC Address13 Register(High)" bitfld.long 0x00 31. " AE_13 ,Address13 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_13_47_32 ,MAC address13 [47:32]" line.long 0x04 "MAR13L,MAC Address13 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x60)++0x07 line.long 0x00 "MAR13H,MAC Address13 Register(High)" bitfld.long 0x00 31. " AE_13 ,Address13 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_13_47_32 ,MAC address13 [47:32]" line.long 0x04 "MAR13L,MAC Address13 Register(Low) [31:0]" else group.long (0x48+0x60)++0x07 line.long 0x00 "MAR13H,MAC Address13 Register(High)" bitfld.long 0x00 31. " AE_13 ,Address13 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_13_47_32 ,MAC address13 [47:32]" line.long 0x04 "MAR13L,MAC Address13 Register(Low) [31:0]" endif endif if (14.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x68)++0x07 line.long 0x00 "MAR14H,MAC Address14 Register(High)" bitfld.long 0x00 31. " AE_14 ,Address14 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_14_47_32 ,MAC address14 [47:32]" line.long 0x04 "MAR14L,MAC Address14 Register(Low) [31:0]" else group.long (0x48+0x68)++0x07 line.long 0x00 "MAR14H,MAC Address14 Register(High)" bitfld.long 0x00 31. " AE_14 ,Address14 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_14_47_32 ,MAC address14 [47:32]" line.long 0x04 "MAR14L,MAC Address14 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x68)++0x07 line.long 0x00 "MAR14H,MAC Address14 Register(High)" bitfld.long 0x00 31. " AE_14 ,Address14 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_14_47_32 ,MAC address14 [47:32]" line.long 0x04 "MAR14L,MAC Address14 Register(Low) [31:0]" else group.long (0x48+0x68)++0x07 line.long 0x00 "MAR14H,MAC Address14 Register(High)" bitfld.long 0x00 31. " AE_14 ,Address14 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_14_47_32 ,MAC address14 [47:32]" line.long 0x04 "MAR14L,MAC Address14 Register(Low) [31:0]" endif endif if (15.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x70)++0x07 line.long 0x00 "MAR15H,MAC Address15 Register(High)" bitfld.long 0x00 31. " AE_15 ,Address15 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_15_47_32 ,MAC address15 [47:32]" line.long 0x04 "MAR15L,MAC Address15 Register(Low) [31:0]" else group.long (0x48+0x70)++0x07 line.long 0x00 "MAR15H,MAC Address15 Register(High)" bitfld.long 0x00 31. " AE_15 ,Address15 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_15_47_32 ,MAC address15 [47:32]" line.long 0x04 "MAR15L,MAC Address15 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x70)++0x07 line.long 0x00 "MAR15H,MAC Address15 Register(High)" bitfld.long 0x00 31. " AE_15 ,Address15 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_15_47_32 ,MAC address15 [47:32]" line.long 0x04 "MAR15L,MAC Address15 Register(Low) [31:0]" else group.long (0x48+0x70)++0x07 line.long 0x00 "MAR15H,MAC Address15 Register(High)" bitfld.long 0x00 31. " AE_15 ,Address15 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_15_47_32 ,MAC address15 [47:32]" line.long 0x04 "MAR15L,MAC Address15 Register(Low) [31:0]" endif endif if (16.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x78)++0x07 line.long 0x00 "MAR16H,MAC Address16 Register(High)" bitfld.long 0x00 31. " AE_16 ,Address16 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_16_47_32 ,MAC address16 [47:32]" line.long 0x04 "MAR16L,MAC Address16 Register(Low) [31:0]" else group.long (0x48+0x78)++0x07 line.long 0x00 "MAR16H,MAC Address16 Register(High)" bitfld.long 0x00 31. " AE_16 ,Address16 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_16_47_32 ,MAC address16 [47:32]" line.long 0x04 "MAR16L,MAC Address16 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x78)++0x07 line.long 0x00 "MAR16H,MAC Address16 Register(High)" bitfld.long 0x00 31. " AE_16 ,Address16 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_16_47_32 ,MAC address16 [47:32]" line.long 0x04 "MAR16L,MAC Address16 Register(Low) [31:0]" else group.long (0x48+0x78)++0x07 line.long 0x00 "MAR16H,MAC Address16 Register(High)" bitfld.long 0x00 31. " AE_16 ,Address16 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_16_47_32 ,MAC address16 [47:32]" line.long 0x04 "MAR16L,MAC Address16 Register(Low) [31:0]" endif endif if (17.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x80)++0x07 line.long 0x00 "MAR17H,MAC Address17 Register(High)" bitfld.long 0x00 31. " AE_17 ,Address17 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_17_47_32 ,MAC address17 [47:32]" line.long 0x04 "MAR17L,MAC Address17 Register(Low) [31:0]" else group.long (0x48+0x80)++0x07 line.long 0x00 "MAR17H,MAC Address17 Register(High)" bitfld.long 0x00 31. " AE_17 ,Address17 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_17_47_32 ,MAC address17 [47:32]" line.long 0x04 "MAR17L,MAC Address17 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x80)++0x07 line.long 0x00 "MAR17H,MAC Address17 Register(High)" bitfld.long 0x00 31. " AE_17 ,Address17 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_17_47_32 ,MAC address17 [47:32]" line.long 0x04 "MAR17L,MAC Address17 Register(Low) [31:0]" else group.long (0x48+0x80)++0x07 line.long 0x00 "MAR17H,MAC Address17 Register(High)" bitfld.long 0x00 31. " AE_17 ,Address17 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_17_47_32 ,MAC address17 [47:32]" line.long 0x04 "MAR17L,MAC Address17 Register(Low) [31:0]" endif endif if (18.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x88)++0x07 line.long 0x00 "MAR18H,MAC Address18 Register(High)" bitfld.long 0x00 31. " AE_18 ,Address18 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_18_47_32 ,MAC address18 [47:32]" line.long 0x04 "MAR18L,MAC Address18 Register(Low) [31:0]" else group.long (0x48+0x88)++0x07 line.long 0x00 "MAR18H,MAC Address18 Register(High)" bitfld.long 0x00 31. " AE_18 ,Address18 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_18_47_32 ,MAC address18 [47:32]" line.long 0x04 "MAR18L,MAC Address18 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x88)++0x07 line.long 0x00 "MAR18H,MAC Address18 Register(High)" bitfld.long 0x00 31. " AE_18 ,Address18 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_18_47_32 ,MAC address18 [47:32]" line.long 0x04 "MAR18L,MAC Address18 Register(Low) [31:0]" else group.long (0x48+0x88)++0x07 line.long 0x00 "MAR18H,MAC Address18 Register(High)" bitfld.long 0x00 31. " AE_18 ,Address18 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_18_47_32 ,MAC address18 [47:32]" line.long 0x04 "MAR18L,MAC Address18 Register(Low) [31:0]" endif endif if (19.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x90)++0x07 line.long 0x00 "MAR19H,MAC Address19 Register(High)" bitfld.long 0x00 31. " AE_19 ,Address19 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_19_47_32 ,MAC address19 [47:32]" line.long 0x04 "MAR19L,MAC Address19 Register(Low) [31:0]" else group.long (0x48+0x90)++0x07 line.long 0x00 "MAR19H,MAC Address19 Register(High)" bitfld.long 0x00 31. " AE_19 ,Address19 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_19_47_32 ,MAC address19 [47:32]" line.long 0x04 "MAR19L,MAC Address19 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x90)++0x07 line.long 0x00 "MAR19H,MAC Address19 Register(High)" bitfld.long 0x00 31. " AE_19 ,Address19 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_19_47_32 ,MAC address19 [47:32]" line.long 0x04 "MAR19L,MAC Address19 Register(Low) [31:0]" else group.long (0x48+0x90)++0x07 line.long 0x00 "MAR19H,MAC Address19 Register(High)" bitfld.long 0x00 31. " AE_19 ,Address19 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_19_47_32 ,MAC address19 [47:32]" line.long 0x04 "MAR19L,MAC Address19 Register(Low) [31:0]" endif endif if (20.<10.) sif (cpuis("MB86R12")) group.long (0x48+0x98)++0x07 line.long 0x00 "MAR20H,MAC Address20 Register(High)" bitfld.long 0x00 31. " AE_20 ,Address20 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_20_47_32 ,MAC address20 [47:32]" line.long 0x04 "MAR20L,MAC Address20 Register(Low) [31:0]" else group.long (0x48+0x98)++0x07 line.long 0x00 "MAR20H,MAC Address20 Register(High)" bitfld.long 0x00 31. " AE_20 ,Address20 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_20_47_32 ,MAC address20 [47:32]" line.long 0x04 "MAR20L,MAC Address20 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0x98)++0x07 line.long 0x00 "MAR20H,MAC Address20 Register(High)" bitfld.long 0x00 31. " AE_20 ,Address20 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_20_47_32 ,MAC address20 [47:32]" line.long 0x04 "MAR20L,MAC Address20 Register(Low) [31:0]" else group.long (0x48+0x98)++0x07 line.long 0x00 "MAR20H,MAC Address20 Register(High)" bitfld.long 0x00 31. " AE_20 ,Address20 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_20_47_32 ,MAC address20 [47:32]" line.long 0x04 "MAR20L,MAC Address20 Register(Low) [31:0]" endif endif if (21.<10.) sif (cpuis("MB86R12")) group.long (0x48+0xA0)++0x07 line.long 0x00 "MAR21H,MAC Address21 Register(High)" bitfld.long 0x00 31. " AE_21 ,Address21 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_21_47_32 ,MAC address21 [47:32]" line.long 0x04 "MAR21L,MAC Address21 Register(Low) [31:0]" else group.long (0x48+0xA0)++0x07 line.long 0x00 "MAR21H,MAC Address21 Register(High)" bitfld.long 0x00 31. " AE_21 ,Address21 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_21_47_32 ,MAC address21 [47:32]" line.long 0x04 "MAR21L,MAC Address21 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0xA0)++0x07 line.long 0x00 "MAR21H,MAC Address21 Register(High)" bitfld.long 0x00 31. " AE_21 ,Address21 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_21_47_32 ,MAC address21 [47:32]" line.long 0x04 "MAR21L,MAC Address21 Register(Low) [31:0]" else group.long (0x48+0xA0)++0x07 line.long 0x00 "MAR21H,MAC Address21 Register(High)" bitfld.long 0x00 31. " AE_21 ,Address21 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_21_47_32 ,MAC address21 [47:32]" line.long 0x04 "MAR21L,MAC Address21 Register(Low) [31:0]" endif endif if (22.<10.) sif (cpuis("MB86R12")) group.long (0x48+0xA8)++0x07 line.long 0x00 "MAR22H,MAC Address22 Register(High)" bitfld.long 0x00 31. " AE_22 ,Address22 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_22_47_32 ,MAC address22 [47:32]" line.long 0x04 "MAR22L,MAC Address22 Register(Low) [31:0]" else group.long (0x48+0xA8)++0x07 line.long 0x00 "MAR22H,MAC Address22 Register(High)" bitfld.long 0x00 31. " AE_22 ,Address22 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_22_47_32 ,MAC address22 [47:32]" line.long 0x04 "MAR22L,MAC Address22 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0xA8)++0x07 line.long 0x00 "MAR22H,MAC Address22 Register(High)" bitfld.long 0x00 31. " AE_22 ,Address22 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_22_47_32 ,MAC address22 [47:32]" line.long 0x04 "MAR22L,MAC Address22 Register(Low) [31:0]" else group.long (0x48+0xA8)++0x07 line.long 0x00 "MAR22H,MAC Address22 Register(High)" bitfld.long 0x00 31. " AE_22 ,Address22 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_22_47_32 ,MAC address22 [47:32]" line.long 0x04 "MAR22L,MAC Address22 Register(Low) [31:0]" endif endif if (23.<10.) sif (cpuis("MB86R12")) group.long (0x48+0xB0)++0x07 line.long 0x00 "MAR23H,MAC Address23 Register(High)" bitfld.long 0x00 31. " AE_23 ,Address23 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_23_47_32 ,MAC address23 [47:32]" line.long 0x04 "MAR23L,MAC Address23 Register(Low) [31:0]" else group.long (0x48+0xB0)++0x07 line.long 0x00 "MAR23H,MAC Address23 Register(High)" bitfld.long 0x00 31. " AE_23 ,Address23 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_23_47_32 ,MAC address23 [47:32]" line.long 0x04 "MAR23L,MAC Address23 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0xB0)++0x07 line.long 0x00 "MAR23H,MAC Address23 Register(High)" bitfld.long 0x00 31. " AE_23 ,Address23 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_23_47_32 ,MAC address23 [47:32]" line.long 0x04 "MAR23L,MAC Address23 Register(Low) [31:0]" else group.long (0x48+0xB0)++0x07 line.long 0x00 "MAR23H,MAC Address23 Register(High)" bitfld.long 0x00 31. " AE_23 ,Address23 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_23_47_32 ,MAC address23 [47:32]" line.long 0x04 "MAR23L,MAC Address23 Register(Low) [31:0]" endif endif if (24.<10.) sif (cpuis("MB86R12")) group.long (0x48+0xB8)++0x07 line.long 0x00 "MAR24H,MAC Address24 Register(High)" bitfld.long 0x00 31. " AE_24 ,Address24 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_24_47_32 ,MAC address24 [47:32]" line.long 0x04 "MAR24L,MAC Address24 Register(Low) [31:0]" else group.long (0x48+0xB8)++0x07 line.long 0x00 "MAR24H,MAC Address24 Register(High)" bitfld.long 0x00 31. " AE_24 ,Address24 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_24_47_32 ,MAC address24 [47:32]" line.long 0x04 "MAR24L,MAC Address24 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0xB8)++0x07 line.long 0x00 "MAR24H,MAC Address24 Register(High)" bitfld.long 0x00 31. " AE_24 ,Address24 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_24_47_32 ,MAC address24 [47:32]" line.long 0x04 "MAR24L,MAC Address24 Register(Low) [31:0]" else group.long (0x48+0xB8)++0x07 line.long 0x00 "MAR24H,MAC Address24 Register(High)" bitfld.long 0x00 31. " AE_24 ,Address24 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_24_47_32 ,MAC address24 [47:32]" line.long 0x04 "MAR24L,MAC Address24 Register(Low) [31:0]" endif endif if (25.<10.) sif (cpuis("MB86R12")) group.long (0x48+0xC0)++0x07 line.long 0x00 "MAR25H,MAC Address25 Register(High)" bitfld.long 0x00 31. " AE_25 ,Address25 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_25_47_32 ,MAC address25 [47:32]" line.long 0x04 "MAR25L,MAC Address25 Register(Low) [31:0]" else group.long (0x48+0xC0)++0x07 line.long 0x00 "MAR25H,MAC Address25 Register(High)" bitfld.long 0x00 31. " AE_25 ,Address25 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_25_47_32 ,MAC address25 [47:32]" line.long 0x04 "MAR25L,MAC Address25 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0xC0)++0x07 line.long 0x00 "MAR25H,MAC Address25 Register(High)" bitfld.long 0x00 31. " AE_25 ,Address25 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_25_47_32 ,MAC address25 [47:32]" line.long 0x04 "MAR25L,MAC Address25 Register(Low) [31:0]" else group.long (0x48+0xC0)++0x07 line.long 0x00 "MAR25H,MAC Address25 Register(High)" bitfld.long 0x00 31. " AE_25 ,Address25 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_25_47_32 ,MAC address25 [47:32]" line.long 0x04 "MAR25L,MAC Address25 Register(Low) [31:0]" endif endif if (26.<10.) sif (cpuis("MB86R12")) group.long (0x48+0xC8)++0x07 line.long 0x00 "MAR26H,MAC Address26 Register(High)" bitfld.long 0x00 31. " AE_26 ,Address26 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_26_47_32 ,MAC address26 [47:32]" line.long 0x04 "MAR26L,MAC Address26 Register(Low) [31:0]" else group.long (0x48+0xC8)++0x07 line.long 0x00 "MAR26H,MAC Address26 Register(High)" bitfld.long 0x00 31. " AE_26 ,Address26 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_26_47_32 ,MAC address26 [47:32]" line.long 0x04 "MAR26L,MAC Address26 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0xC8)++0x07 line.long 0x00 "MAR26H,MAC Address26 Register(High)" bitfld.long 0x00 31. " AE_26 ,Address26 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_26_47_32 ,MAC address26 [47:32]" line.long 0x04 "MAR26L,MAC Address26 Register(Low) [31:0]" else group.long (0x48+0xC8)++0x07 line.long 0x00 "MAR26H,MAC Address26 Register(High)" bitfld.long 0x00 31. " AE_26 ,Address26 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_26_47_32 ,MAC address26 [47:32]" line.long 0x04 "MAR26L,MAC Address26 Register(Low) [31:0]" endif endif if (27.<10.) sif (cpuis("MB86R12")) group.long (0x48+0xD0)++0x07 line.long 0x00 "MAR27H,MAC Address27 Register(High)" bitfld.long 0x00 31. " AE_27 ,Address27 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_27_47_32 ,MAC address27 [47:32]" line.long 0x04 "MAR27L,MAC Address27 Register(Low) [31:0]" else group.long (0x48+0xD0)++0x07 line.long 0x00 "MAR27H,MAC Address27 Register(High)" bitfld.long 0x00 31. " AE_27 ,Address27 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_27_47_32 ,MAC address27 [47:32]" line.long 0x04 "MAR27L,MAC Address27 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0xD0)++0x07 line.long 0x00 "MAR27H,MAC Address27 Register(High)" bitfld.long 0x00 31. " AE_27 ,Address27 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_27_47_32 ,MAC address27 [47:32]" line.long 0x04 "MAR27L,MAC Address27 Register(Low) [31:0]" else group.long (0x48+0xD0)++0x07 line.long 0x00 "MAR27H,MAC Address27 Register(High)" bitfld.long 0x00 31. " AE_27 ,Address27 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_27_47_32 ,MAC address27 [47:32]" line.long 0x04 "MAR27L,MAC Address27 Register(Low) [31:0]" endif endif if (28.<10.) sif (cpuis("MB86R12")) group.long (0x48+0xD8)++0x07 line.long 0x00 "MAR28H,MAC Address28 Register(High)" bitfld.long 0x00 31. " AE_28 ,Address28 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_28_47_32 ,MAC address28 [47:32]" line.long 0x04 "MAR28L,MAC Address28 Register(Low) [31:0]" else group.long (0x48+0xD8)++0x07 line.long 0x00 "MAR28H,MAC Address28 Register(High)" bitfld.long 0x00 31. " AE_28 ,Address28 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_28_47_32 ,MAC address28 [47:32]" line.long 0x04 "MAR28L,MAC Address28 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0xD8)++0x07 line.long 0x00 "MAR28H,MAC Address28 Register(High)" bitfld.long 0x00 31. " AE_28 ,Address28 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_28_47_32 ,MAC address28 [47:32]" line.long 0x04 "MAR28L,MAC Address28 Register(Low) [31:0]" else group.long (0x48+0xD8)++0x07 line.long 0x00 "MAR28H,MAC Address28 Register(High)" bitfld.long 0x00 31. " AE_28 ,Address28 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_28_47_32 ,MAC address28 [47:32]" line.long 0x04 "MAR28L,MAC Address28 Register(Low) [31:0]" endif endif if (29.<10.) sif (cpuis("MB86R12")) group.long (0x48+0xE0)++0x07 line.long 0x00 "MAR29H,MAC Address29 Register(High)" bitfld.long 0x00 31. " AE_29 ,Address29 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_29_47_32 ,MAC address29 [47:32]" line.long 0x04 "MAR29L,MAC Address29 Register(Low) [31:0]" else group.long (0x48+0xE0)++0x07 line.long 0x00 "MAR29H,MAC Address29 Register(High)" bitfld.long 0x00 31. " AE_29 ,Address29 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_29_47_32 ,MAC address29 [47:32]" line.long 0x04 "MAR29L,MAC Address29 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0xE0)++0x07 line.long 0x00 "MAR29H,MAC Address29 Register(High)" bitfld.long 0x00 31. " AE_29 ,Address29 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_29_47_32 ,MAC address29 [47:32]" line.long 0x04 "MAR29L,MAC Address29 Register(Low) [31:0]" else group.long (0x48+0xE0)++0x07 line.long 0x00 "MAR29H,MAC Address29 Register(High)" bitfld.long 0x00 31. " AE_29 ,Address29 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_29_47_32 ,MAC address29 [47:32]" line.long 0x04 "MAR29L,MAC Address29 Register(Low) [31:0]" endif endif if (30.<10.) sif (cpuis("MB86R12")) group.long (0x48+0xE8)++0x07 line.long 0x00 "MAR30H,MAC Address30 Register(High)" bitfld.long 0x00 31. " AE_30 ,Address30 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_30_47_32 ,MAC address30 [47:32]" line.long 0x04 "MAR30L,MAC Address30 Register(Low) [31:0]" else group.long (0x48+0xE8)++0x07 line.long 0x00 "MAR30H,MAC Address30 Register(High)" bitfld.long 0x00 31. " AE_30 ,Address30 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_30_47_32 ,MAC address30 [47:32]" line.long 0x04 "MAR30L,MAC Address30 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0xE8)++0x07 line.long 0x00 "MAR30H,MAC Address30 Register(High)" bitfld.long 0x00 31. " AE_30 ,Address30 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_30_47_32 ,MAC address30 [47:32]" line.long 0x04 "MAR30L,MAC Address30 Register(Low) [31:0]" else group.long (0x48+0xE8)++0x07 line.long 0x00 "MAR30H,MAC Address30 Register(High)" bitfld.long 0x00 31. " AE_30 ,Address30 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_30_47_32 ,MAC address30 [47:32]" line.long 0x04 "MAR30L,MAC Address30 Register(Low) [31:0]" endif endif if (31.<10.) sif (cpuis("MB86R12")) group.long (0x48+0xF0)++0x07 line.long 0x00 "MAR31H,MAC Address31 Register(High)" bitfld.long 0x00 31. " AE_31 ,Address31 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_31_47_32 ,MAC address31 [47:32]" line.long 0x04 "MAR31L,MAC Address31 Register(Low) [31:0]" else group.long (0x48+0xF0)++0x07 line.long 0x00 "MAR31H,MAC Address31 Register(High)" bitfld.long 0x00 31. " AE_31 ,Address31 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_31_47_32 ,MAC address31 [47:32]" line.long 0x04 "MAR31L,MAC Address31 Register(Low) [31:0]" endif else sif (cpuis("MB86R12")) group.long (0x48+0xF0)++0x07 line.long 0x00 "MAR31H,MAC Address31 Register(High)" bitfld.long 0x00 31. " AE_31 ,Address31 enable" "Disabled,Enabled" rbitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" rbitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " rbitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" rbitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" rbitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " rbitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" rbitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_31_47_32 ,MAC address31 [47:32]" line.long 0x04 "MAR31L,MAC Address31 Register(Low) [31:0]" else group.long (0x48+0xF0)++0x07 line.long 0x00 "MAR31H,MAC Address31 Register(High)" bitfld.long 0x00 31. " AE_31 ,Address31 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" bitfld.long 0x00 29. " MBC5 ,Mask Byte Control reg. 18[15:8]" "Not masked,Masked" textline " " bitfld.long 0x00 28. " MBC4 ,Mask Byte Control reg. 18[7:0]" "Not masked,Masked" bitfld.long 0x00 27. " MBC3 ,Mask Byte Control reg. 19[31:24]" "Not masked,Masked" bitfld.long 0x00 26. " MBC2 ,Mask Byte Control reg. 19[23:16]" "Not masked,Masked" textline " " bitfld.long 0x00 25. " MBC1 ,Mask Byte Control reg. 19[15:8]" "Not masked,Masked" bitfld.long 0x00 24. " MBC0 ,Mask Byte Control reg. 19[7:0]" "Not masked,Masked" hexmask.long.word 0x00 0.--15. 1. " A_31_47_32 ,MAC address31 [47:32]" line.long 0x04 "MAR31L,MAC Address31 Register(Low) [31:0]" endif endif rgroup.long 0xD8++0x03 line.long 0x00 "RGSR,RGMII Status register" bitfld.long 0x00 3. " LS ,Link Status" "Down,Up" bitfld.long 0x00 1.--2. " LSP ,Link Speed" "2.5 MHz,25 MHz,125 MHz," bitfld.long 0x00 0. " LM ,Link Mode" "Half-Duplex,Full-Duplex" width 22. tree "MMC Registers" group.long 0x100++0x13 line.long 0x00 "MMC_CNTL,MMC Control establishes the operating mode of MMC Counters" bitfld.long 0x00 5. " FHP ,Full-Half preset" "Half,Full" bitfld.long 0x00 4. " CP ,Counters Preset" "Half,Full" textline " " bitfld.long 0x00 3. " MMCCF ,MMC Counter Freeze" "No freeze,Freeze" eventfld.long 0x00 2. " RoR ,Reset on read" "No reset,Reset" textline " " bitfld.long 0x00 1. " CSR ,Counter Stop Rollover" "Not set,Set" bitfld.long 0x00 0. " CR ,Counter reset" "No reset,Reset" line.long 0x04 "MMC_INTR_RX,MMC Receive Interrupt maintains the interrupt generated from all of the receive statistic counters" bitfld.long 0x04 23. " RXWATCHDOG_ERR ,This bit is set to '1' when the rxwatchdog errorcounter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x04 22. " RXVLANFRAMES_GB ,This bit is set to '1' when the rxvlanframes_gb counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x04 21. " RXFIFOOVERFLOW_GB ,This bit is set to '1' when the Rxfifooverflow_gb counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x04 20. " RXPAUSEFRAMES ,This bit is set to '1' when the rxpauseframes counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x04 19. " RXOUTOFRANGETYPE ,This bit is set to '1' when the rxoutofrangetype counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x04 18. " RXLENGTHERROR ,This bit is set to '1' when the Rxlengtherror counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x04 17. " RXUNICASTFRAMES_GB ,This bit is set to '1' when the rxunicastframes_gb counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x04 16. " RX1024TOMAXOCTETS_GB ,This bit is set to '1' when the rx1024tomaxoctets_gb counter reaches half themaximum value" "Not Reached,reached" textline " " bitfld.long 0x04 15. " RX512TO1023OCTETS_GB ,This bit is set to '1' when the rx512to1023octets_gb counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x04 14. " RX256TO511OCTETS_GB ,This bit is set to '1' when the rx256to511octets_gb counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x04 13. " RX128TO255MAXOCTECTS_GB ,This bit is set to '1' when the rx128to255maxoctects_gb counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x04 12. " RX65TO127MAXOCTETS_GB ,This bit is set to '1' when the rx65to127maxoctets_gb counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x04 11. " RXTO64OCTETS_GB ,This bit is set to '1' when the rxto64octets_gb counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x04 10. " RXOVERSIZE_G ,This bit is set to '1' when the rxoversize_g counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x04 9. " RXUNDERSIZE_G ,This bit is set to '1' when the rxundersize_g counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x04 8. " RXJABBERERROR ,This bit is set to '1' when the Rxjabbererror counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x04 7. " RXRUNTERROR ,This bit is set to '1' when the rxrunterror counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x04 6. " RXALLIGNMENTERROR ,This bit is set to '1' when the rxallignmenterror counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x04 5. " RXCRCERROR ,This bit is set to '1' when the rxcrcerror counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x04 4. " RXMULTICASTFRAMES_G ,This bit is set to '1' when the rxmulticastframes_g counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x04 3. " RXBROADCASTFRAMES_G ,This bit is set to '1' when the rxbroadcastframes_g counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x04 2. " RXOCTETCOUNTER_G ,This bit is set to '1' when the rxoctetcounter_g counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x04 1. " RXOCTETCOUNTER_GB ,This bit is set to '1' when the rxoctetcounter_gb counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x04 0. " RXFRAMECOUNT_GB ,This bit is set to '1' when the Rxframecount_gb counter reaches half the maximum value" "Not Reached,reached" line.long 0x08 "MMC_INTR_TX,MMC Transmit Interrupt maintains the interrupt generated from all of the transmit statistic counters" bitfld.long 0x08 24. " TXVLANFRAMES_GB ,This bit is set to '1' when the txvlanframes_gb counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x08 23. " TXPAUSEFRAMES_GB ,This bit is set to '1' when the txpauseframes_gb counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x08 22. " TXOEXCESSDEF ,This bit is set to '1' when the txoexcessdef counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x08 21. " TXFRAMECOUNT ,This bit is set to '1' when the txframecount counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x08 20. " TXOCTETCOUNT ,This bit is set to '1' when the txoctetcount counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x08 19. " TXCARRIERERROR ,This bit is set to '1' when the txcarriererror counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x08 18. " TXLEXESSCOL ,This bit is set to '1' when the txlexesscol counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x08 17. " TXLATECOL ,This bit is set to '1' when the txlatecol counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x08 16. " TXDEFFER ,This bit is set to '1' when the txdeffer counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x08 15. " TXMULTICOL_G ,This bit is set to '1' when the txmulticol_g counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x08 14. " TXSINGLECOL_G ,This bit is set to '1' when the txsinglecol_g counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x08 13. " TXUNDERFLOWERROR ,This bit is set to '1' when the txunderflowerror counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x08 12. " TXBROADCASTFRAMES_GB ,This bit is set to '1' when the txbroadcastframes_gb counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x08 11. " TXMULTICASTFRAMES_GB ,This bit is set to '1' when the txmulticastframes_gb counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x08 10. " TXUNICASTFRAMES_GB ,This bit is set to '1' when the txunicastframes_gb counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x08 9. " TX1024TOMAXOCTETS_GB ,This bit is set to '1' when the tx1024tomaxoctets_gb counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x08 8. " TX512TO1023OCTETS_GB ,This bit is set to '1' when the tx512to1023octets_gb counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x08 7. " TX256TO511OCTETS_GB ,This bit is set to '1' when the tx256to511octets_gb counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x08 6. " TX128TO255MAXOCTECTS_GB ,This bit is set to '1' when the tx128to255maxoctects_gb counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x08 5. " TX65TO127MAXOCTETS_GB ,This bit is set to '1' when the tx65to127maxoctets_gb counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x08 4. " TX64OCTETS_GB ,This bit is set to '1' when the tx64octets_gb counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x08 3. " TXMALTICASTFRAMES_G ,This bit is set to '1' when the txmalticastframes_g counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x08 2. " TXBROADCASTFRAMES_G ,This bit is set to '1' when the txbroadcastframes_g counter reaches half the maximum value" "Not Reached,reached" bitfld.long 0x08 1. " TXFRAMECOUNT_GB ,This bit is set to '1' when the txframecount_gb counter reaches half the maximum value" "Not Reached,reached" textline " " bitfld.long 0x08 0. " TXOCTETCOUNT_GB ,This bit is set to '1' when the txoctetcount_gb counter reaches half the maximum value" "Not Reached,reached" line.long 0x0C "MMC_INTR_MASK_RX,MMC Receive Interrupt mask maintains the mask for the interrupt generated from all of the receive statistic counters" bitfld.long 0x0C 23. " RXWATCHDOGERROR ,Setting this bit masks the interrupt when the rxwatchdogerror counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x0C 22. " RXVLANFRAMES_GB ,Setting this bit masks the interrupt when the rxvlanframes_gb counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x0C 21. " RXFIFOOVERFLOW_GB ,Setting this bit masks the interrupt when the rxfifooverflow_gb counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x0C 20. " RXPAUSEFRAMES ,Setting this bit masks the interrupt when the rxpauseframes counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x0C 19. " RXOUTOFRANGETYPE ,Setting this bit masks the interrupt when the rxoutofrangetype counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x0C 18. " RXLENGTHERROR ,Setting this bit masks the interrupt when the rxlengtherror counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x0C 17. " RXUNICASTFRAMES_GB ,Setting this bit masks the interrupt when the rxunicastframes_gb counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x0C 16. " RX1024TOMAXOCTETS_GB ,Setting this bit masks the interrupt when the rx1024tomaxoctets_gb counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x0C 15. " RX512TO1023OCTETS_GB ,Setting this bit masks the interrupt when the rx512to1023octets_gb counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x0C 14. " RX256TO511OCTETS_GB ,Setting this bit masks the interrupt when the rx256to511octets_gb counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x0C 13. " RX128TO255MAXOCTECTS_GB ,Setting this bit masks the interrupt when the rx128to255maxoctects_gb counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x0C 12. " RX65TO127MAXOCTETS_GB ,Setting this bit masks the interrupt when the rx65to127maxoctets_gb counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x0C 11. " RXTO64OCTETS_GB ,Setting this bit masks the interrupt when the rxto64octets_gb counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x0C 10. " RXOVERSIZE_G ,Setting this bit masks the interrupt when the rxoversize_g counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x0C 9. " RXUNDERSIZE_G ,Setting this bit masks the interrupt when the rxundersize_g counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x0C 8. " RXJABBERERROR ,Setting this bit masks the interrupt when the rxjabbererror counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x0C 7. " RXRUNTERROR ,Setting this bit masks the interrupt when the rxrunterror counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x0C 6. " RXALLIGNMENTERROR ,Setting this bit masks the interrupt when the rxallignmenterror counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x0C 5. " RXCRCERROR ,Setting this bit masks the interrupt when the rxcrcerror counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x0C 4. " RXMULTICASTFRAMES_G ,Setting this bit masks the interrupt when the rxmulticastframes_g counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x0C 3. " RXBROADCASTFRAMES_G ,Setting this bit masks the interrupt when the rxbroadcastframes_g counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x0C 2. " RXOCTETCOUNTER_G ,Setting this bit masks the interrupt when the rxoctetcounter_g counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x0C 1. " RXOCTETCOUNTER_GB ,Setting this bit masks the interrupt when the rxoctetcounter_gb counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x0C 0. " RXFRAMECOUNT_GB ,Setting this bit masks the interrupt when the rxframecount_gb counter reaches half the maximum value" "Not masked,Masked" line.long 0x10 "MMC_INTR_MASK_TX,MMC Transmit Interrupt mask maintains the mask for the interrupt generated from all of the transmit statistic counters" bitfld.long 0x10 24. " TXVLANFRAMES_GB ,Setting this bit masks the interrupt when the txvlanframes_gb counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x10 23. " TXPAUSEFRAMES_GB ,Setting this bit masks the interrupt when the txpauseframes_gb counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x10 22. " TXOEXCESSDEF ,Setting this bit masks the interrupt when the txoexcessdef counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x10 21. " TXFRAMECOUNT ,Setting this bit masks the interrupt when the txframecount counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x10 20. " TXOCTETCOUNT ,Setting this bit masks the interrupt when the txoctetcount counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x10 19. " TXCARRIERERROR ,Setting this bit masks the interrupt when the txcarriererror counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x10 18. " TXLEXESSCOL ,Setting this bit masks the interrupt when the txlexesscol counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x10 17. " TXLATECOL ,Setting this bit masks the interrupt when the txlatecol counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x10 16. " TXDEFFER ,Setting this bit masks the interrupt when the txdeffer counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x10 15. " TXMULTICOL_G ,Setting this bit masks the interrupt when the txmulticol_g counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x10 14. " TXSINGLECOL_G ,Setting this bit masks the interrupt when the txsinglecol_g counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x10 13. " TXUNDERFLOWERROR ,Setting this bit masks the interrupt when the txunderflowerror counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x10 12. " TXBROADCASTFRAMES_GB ,Setting this bit masks the interrupt when the txbroadcastframes_gb counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x10 11. " TXMULTICASTFRAMES_GB ,Setting this bit masks the interrupt when the txmulticastframes_gb counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x10 10. " TXUNICASTFRAMES_GB ,Setting this bit masks the interrupt when the txunicastframes_gb counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x10 9. " TX1024TOMAXOCTETS_GB ,Setting this bit masks the interrupt when the tx1024tomaxoctets_gb counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x10 8. " TX512TO1023OCTETS_GB ,Setting this bit masks the interrupt when the tx512to1023octets_gb counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x10 7. " TX256TO511OCTETS_GB ,Setting this bit masks the interrupt when the tx256to511octets_gb counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x10 6. " TX128TO255MAXOCTECTS_GB ,Setting this bit masks the interrupt when the tx128to255maxoctects_gb counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x10 5. " TX65TO127MAXOCTETS_GB ,Setting this bit masks the interrupt when the tx65to127maxoctets_gb counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x10 4. " TXTO64OCTETS_GB ,Setting this bit masks the interrupt when the txto64octets_gb counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x10 3. " TXMALTICASTFRAMES_G ,Setting this bit masks the interrupt when the txmalticastframes_g counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x10 2. " TXBROADCASTFRAMES_G ,Setting this bit masks the interrupt when the txbroadcastframes_g counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x10 1. " TXFRAMECOUNT_GB ,Setting this bit masks the interrupt when the txframecount_gb counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x10 0. " TXOCTETCOUNT_GB ,Setting this bit masks the interrupt when the txoctetcount_gb counter reaches half the maximum value" "Not masked,Masked" rgroup.long 0x114++0x2B line.long 0x00 "TXOCTETCOUNT_GB,Number of bytes transmitted exclusive of preamble and retried bytes in good and bad frames" line.long 0x04 "TXFRAMECOUNT_GB,Number of good and bad frames transmitted, exclusive of retried frames" line.long 0x08 "TXBROADCASTFRAMES_G,Number of good broadcast frames transmitted" line.long 0x0C "TXMULTICASTFRAMES_G,Number of good multicast frames transmitted" line.long 0x10 "TX64OCTETS_GB,Number of good and bad frames transmitted with length of 64 bytes exclusive of preamble and retried frames" line.long 0x14 "TX65TO127OCTETS_GB,Number of good and bad frames transmitted with length between 65 and 127 (inclusive) bytes exclusive of preamble and retried frames" line.long 0x18 "TX128TO255OCTETS_GB,Number of good and bad frames transmitted with length between 128 and 255 (inclusive) bytes exclusive of preamble and retried frames" line.long 0x1C "TX256TO511OCTETS_GB,Number of good and bad frames transmitted with length between 256 and 511 (inclusive) bytes exclusive of preamble and retried frames" line.long 0x20 "TX512TO1023OCTETS_GB,Number of good and bad frames transmitted with length between 512 and 1023 (inclusive) bytes exclusive of preamble and retried frames" line.long 0x24 "TX1024TOMAXOCTETS_GB,Number of good and bad frames transmitted with length between 1024 and Maxsize (inclusive) bytes exclusive of preamble and retried frames" line.long 0x28 "TXUNICASTFRAMES_GB,Number of good and bad unicast frames transmitted" rgroup.long 0x140++0x37 line.long 0x00 "TXMULTICASTFRAMES_GB,Number of good and bac multicast frames transmitted" line.long 0x04 "TXBROADCASTFRAMES_GB,Number of good and bad broadcast frames transmitted" line.long 0x08 "TXUNDERFLOWERROR,Number of frames aborted due to frame underflow error" line.long 0x0C "TXSINGLECOL_G,Number of successfully transmitted frames after a single collision in Half-duplex mode" line.long 0x10 "TXMULTICOL_G,Number of successfully transmitted frames after more than a single collision in Half-duplex mode" line.long 0x14 "TXDEFERRED,Number of successfully transmitted frames after a deferral in Halfduplex mode" line.long 0x18 "TXLATECOL,Number of frames aborted due to late collision error" line.long 0x1C "TXEXESSCOL,Number of frames aborted due to excessive (16) collision errors" line.long 0x20 "TXCARRIERERRROR,Number of frames aborted due to carrier sense error (no carrier or loss of carrier)" line.long 0x24 "TXOCTETCOUNT_G,Number of bytes transmitted exclusive of preamble in good frames only" line.long 0x28 "TXFRAMECOUNT_G,Number of good frames transmitted" line.long 0x2C "TXEXECESSDEF,Number of frames aborted due to excessive deferral error (deferred for more than two max-sized frame times)" line.long 0x30 "TXPAUSEFRAMES,Number of good PAUSE frames transmitted" line.long 0x34 "TXVLANFRAMES_G,Number of good VLAN frames transmitted, exclusive of retried frames" rgroup.long 0x180++0x3F line.long 0x00 "RXFRAMECOUNT_GB,Number of good and bad frames received" line.long 0x04 "RXOCTETCOUNT_GB,Number of bytes received exclusive of preamble in good and bad frames" line.long 0x08 "RXOCTETCOUNT_G,Number of bytes received exclusive of preamble only in good frames" line.long 0x0C "RXBROADCASTFRAMES_G,Number of good broadcast frames received" line.long 0x10 "RXMULTICASTFRAMES_G,Number of good multicast frames received" line.long 0x14 "RXCRCERROR,Number of frames received with CRC error" line.long 0x18 "RXALLIGNMENTERROR,Number of frames received with alignment (dribble) error. Valid only in 10/100 mode" line.long 0x1C "RXRUNTERROR,Number of frames received with runt (<64 bytes and CRC error) error" line.long 0x20 "RXJABBERERROR,Number of frames received with length (including CRC) greater than 1518 bytes with CRC error" line.long 0x24 "RXUNDERSIZE_G,Number of frames received with length less than 64 bytes, without any errors" line.long 0x28 "RXOVERSIZE_G,Number of frames received with length greater than the maxsize without error" line.long 0x2C "RX64OCTETS_GB,Number of good and bad frames received with length 64 bytes exclusive of preamble" line.long 0x30 "RX65TO127OCTETS_GB,Number of good and bad frames received with length between 65 and 127 (inclusive) bytes exclusive of preamble" line.long 0x34 "RX128TO255OCTETS_GB,Number of good and bad frames received with length between 128 and 255 (inclusive) bytes exclusive of preamble" line.long 0x38 "RX256TO511OCTETS_GB,Number of good and bad frames received with length between 256 and 511 (inclusive) bytes, exclusive of preamble" line.long 0x3C "RX512TO1023OCTETS_GB,Number of good and bad frames received with length between 512 and 1023 (inclusive) bytes, exclusive of preamble" rgroup.long 0x1C0++0x1F line.long 0x00 "RX1024TOMAXOCTETS_GB,Number of good and bad frames received with length between 1024 and maxsize (inclusive) bytes exclusive of preamble" line.long 0x04 "RXUNICASTFRAMES_G,Number of good unicast frames received" line.long 0x08 "RXLENGTHERROR,Number of frames received with length error (Length type field is not the frame size) for all frames with valid length field" line.long 0x0C "RXOUTOFRANGETYPE,Number of frames received with length/type field not equal to the valid frame size (>1500)" line.long 0x10 "RXPAUSEFRAMES,Number of good and valid PAUSE frames received" line.long 0x14 "RXFIFOOVERFLOW,Number of missed received frames due to FIFO overflow" line.long 0x18 "RXVLANFRAMES_GB,Number of good and bad VLAN frames received" line.long 0x1C "RXWATCHDOGERROR,Number of frames received with error due to watchdog timeout error (frames with a data load larger than 2048 bytes" group.long 0x200++0x03 line.long 0x00 "MMC_IPC_INTR_MASK_RX,MMC IPC Receive Checksum Offload Interrupt Mask maintains the mask for the interrupt generated from the receive IPC statistic counters" bitfld.long 0x00 29. " RXICMP_ERR_OCTETS ,The bit is set when the rxicmp_err_octets counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x00 28. " RXICMP_GD_OCTETS ,The bit is set when the rxicmp_gd_octets counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 27. " RXTCP_ERR_OCTETS ,The bit is set when the rxtcp_err_octets counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x00 26. " RXTCP_GD_OCTETS ,The bit is set when the rxtcp_gd_octets counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 25. " RXUDP_ERR_OCTETS ,The bit is set when the rxudp_err_octets counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x00 24. " RXUDP_GD_OCTETS ,The bit is set when the rxudp_gd_octets counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 23. " RXIPV6_NOPAY_OCTETS ,The bit is set when the rxipv6_nopay_octets counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x00 22. " RXIPV6_HDRERR_OCTETS ,The bit is set when the rxipv6_hdrerr_octets counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 21. " RXIPV6_GD_OCTETS ,The bit is set when the rxipv6_gd_octets counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x00 20. " RXIPV4_UDSBL_OCTETS ,The bit is set when the rxipv4_udsbl_octets counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 19. " RXIPV4_FRAG_OCTETS ,The bit is set when the rxipv4_frag_octets counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x00 18. " RXIPV4_NOPAY_OCTETS ,The bit is set when the rxipv4_nopay_octets counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 17. " RXIPV4_HDRERR_OCTETS ,The bit is set when the rxipv4_hdrerr_octets counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x00 16. " RXIPV4_GD_OCTETS ,The bit is set when the rxipv4_gd_octets counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 13. " RXICMP_ERR_FRMS ,The bit is set when the rxicmp_err_frms counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x00 12. " RXICMP_GD_FRMS ,The bit is set when the rxicmp_gd_frms counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 11. " RXTCP_ERR_FRMS ,The bit is set when the rxtcp_err_frms counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x00 10. " RXTCP_GD_FRMS ,The bit is set when the rxtcp_gd_frms counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 9. " RXUDP_ERR_FRMS ,The bit is set when the rxudp_err_frms counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x00 8. " RXUDP_GD_FRMS ,The bit is set when the rxudp_gd_frms counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 7. " RXIPV6_NOPAY_FRMS ,The bit is set when the rxipv6_nopay_frms counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x00 6. " RXIPV6_HDRERR_FRMS ,The bit is set when the rxipv6_hdrerr_frms counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 5. " RXIPV6_GD_FRMS ,The bit is set when the rxipv6_gd_frms counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x00 4. " RXIPV4_UDSBL_FRMS ,The bit is set when the rxipv4_udsbl_frms counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 3. " RXIPV4_FRAG_FRMS ,The bit is set when the rxipv4_frag_frms counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x00 2. " RXIPV4_NOPAY_FRMS ,The bit is set when the rxipv4_nopay_frms counter reaches half the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 1. " RXIPV4_HDRERR_FRMS ,The bit is set when the rxipv4_hdrerr_frms counter reaches half the maximum value" "Not masked,Masked" bitfld.long 0x00 0. " RXIPV4_GD_FRMS ,The bit is set when the rxipv4_gd_frms counter reaches half the maximum value" "Not masked,Masked" group.long 0x208++0x03 line.long 0x00 "MMC_IPC_INTR_RX,MMC Receive Checksum Offload Interrupt maintains the interrupt that the receive IPC statistic counters generate" bitfld.long 0x00 29. " RXICMP_ERR_OCTETS ,The bit is set when the rxicmp_err_octets counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" bitfld.long 0x00 28. " RXICMP_GD_OCTETS ,The bit is set when the rxicmp_gd_octets counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 27. " RXTCP_ERR_OCTETS ,The bit is set when the rxtcp_err_octets counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" bitfld.long 0x00 26. " RXTCP_GD_OCTETS ,The bit is set when the rxtcp_gd_octets counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 25. " RXUDP_ERR_OCTETS ,The bit is set when the rxudp_err_octets counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" bitfld.long 0x00 24. " RXUDP_GD_OCTETS ,The bit is set when the rxudp_gd_octets counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 23. " RXIPV6_NOPAY_OCTETS ,The bit is set when the rxipv6_nopay_octets counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" bitfld.long 0x00 22. " RXIPV6_HDRERR_OCTETS ,The bit is set when the rxipv6_hdrerr_octets counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 21. " RXIPV6_GD_OCTETS ,The bit is set when the rxipv6_gd_octets counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" bitfld.long 0x00 20. " RXIPV4_UDSBL_OCTETS ,The bit is set when the rxipv4_udsbl_octets counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 19. " RXIPV4_FRAG_OCTETS ,The bit is set when the rxipv4_frag_octets counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" bitfld.long 0x00 18. " RXIPV4_NOPAY_OCTETS ,The bit is set when the rxipv4_nopay_octets counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 17. " RXIPV4_HDRERR_OCTETS ,The bit is set when the rxipv4_hdrerr_octets counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" bitfld.long 0x00 16. " RXIPV4_GD_OCTETS ,The bit is set when the rxipv4_gd_octets counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 13. " RXICMP_ERR_FRMS ,The bit is set when the rxicmp_err_frms counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" bitfld.long 0x00 12. " RXICMP_GD_FRMS ,The bit is set when the rxicmp_gd_frms counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 11. " RXTCP_ERR_FRMS ,The bit is set when the rxtcp_err_frms counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" bitfld.long 0x00 10. " RXTCP_GD_FRMS ,The bit is set when the rxtcp_gd_frms counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 9. " RXUDP_ERR_FRMS ,The bit is set when the rxudp_err_frms counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" bitfld.long 0x00 8. " RXUDP_GD_FRMS ,The bit is set when the rxudp_gd_frms counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 7. " RXIPV6_NOPAY_FRMS ,The bit is set when the rxipv6_nopay_frms counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" bitfld.long 0x00 6. " RXIPV6_HDRERR_FRMS ,The bit is set when the rxipv6_hdrerr_frms counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 5. " RXIPV6_GD_FRMS ,The bit is set when the rxipv6_gd_frms counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" bitfld.long 0x00 4. " RXIPV4_UDSBL_FRMS ,The bit is set when the rxipv4_udsbl_frms counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 3. " RXIPV4_FRAG_FRMS ,The bit is set when the rxipv4_frag_frms counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" bitfld.long 0x00 2. " RXIPV4_NOPAY_FRMS ,The bit is set when the rxipv4_nopay_frms counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" textline " " bitfld.long 0x00 1. " RXIPV4_HDRERR_FRMS ,The bit is set when the rxipv4_hdrerr_frms counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" bitfld.long 0x00 0. " RXIPV4_GD_FRMS ,The bit is set when the rxipv4_gd_frms counter reaches half the maximum value and also when it reaches the maximum value" "Not masked,Masked" rgroup.long 0x210++0x37 line.long 0x00 "RXIPV4_GD_FRMS,Number of good IPv4 datagrams received with the TCP UDP or ICMP payload" line.long 0x04 "RXIPV4_HDRERR_FRMS,Number of IPv4 datagrams received with header (checksum length or version mismatch) errors" line.long 0x08 "RXIPV4_NOPAY_FRMS,Number of IPv4 datagram frames received that did not have a TCP UDP or ICMP payload processed by the Checksum engine" line.long 0x0C "RXIPV4_FRAG_FRMS,Number of good IPv4 datagrams with fragmentation" line.long 0x10 "RXIPV4_UDSBL_FRMS,Number of good IPv4 datagrams received that had a UDP payload with checksum disabled" line.long 0x14 "RXIPV6_GD_FRMS,Number of good IPv6 datagrams received with TCP UDP or ICMP payloads" line.long 0x18 "RXIPV6_HDRERR_FRMS,Number of IPv6 datagrams received with header errors (length or version mismatch)" line.long 0x1C "RXIPV6_NOPAY_FRMS,Number of IPv6 datagram frames received that did not have a TCP UDP or ICMP payload" line.long 0x20 "RXUDP_GD_FRMS,Number of good IP datagrams with a good UDP payload. This counter is not updated when the rxipv4_udsbl_frms counter is incremented" line.long 0x24 "RXUDP_ERR_FRMS,Number of good IP datagrams whose UDP payload has a checksum error" line.long 0x28 "RXTCP_GD_FRMS,Number of good IP datagrams with a good TCP payload" line.long 0x2C "RXTCP_ERR_FRMS,Number of good IP datagrams whose TCP payload has a checksum error" line.long 0x30 "RXICMP_GD_FRMS,Number of good IP datagrams with a good ICMP payload" line.long 0x34 "RXICMP_ERR_FRMS,Number of good IP datagrams whose ICMP payload has a checksum error" rgroup.long 0x250++0x37 line.long 0x00 "RXIPV4_GD_OCTETS,Number of bytes received in good IPv4 datagrams encapsulating TCP UDP or ICMP data" line.long 0x04 "RXIPV4_HDRERR_OCTETS,Number of bytes received in IPv4 datagrams with header errors" line.long 0x08 "RXIPV4_NOPAY_OCTETS,Number of bytes received in IPv4 datagrams that did not have a TCP UDP or ICMP payload" line.long 0x0C "RXIPV4_FRAG_OCTETS,Number of bytes received in fragmented IPv4 datagrams" line.long 0x10 "RXIPV4_UDSBL_OCTETS,Number of bytes received in a UDP segment that had the UDP checksum disabled" line.long 0x14 "RXIPV6_GD_OCTETS,Number of bytes received in good IPv6 datagrams encapsulating TCP UDP or ICMPv6 data" line.long 0x18 "RXIPV6_HDRERR_OCTETS,Number of bytes received in IPv6 datagrams with header errors" line.long 0x1C "RXIPV6_NOPAY_OCTETS,Number of bytes received in IPv6 datagrams that did not have a TCP UDP or ICMP payload" line.long 0x20 "RXUDP_GD_OCTETS,Number of bytes received in a good UDP segment" line.long 0x24 "RXUDP_ERR_OCTETS,Number of bytes received in a UDP segment that had checksum errors" line.long 0x28 "RXTCP_GD_OCTETS,Number of bytes received in a good TCP segment" line.long 0x2C "RXTCP_ERR_OCTETS,Number of bytes received in a TCP segment with checksum errors" line.long 0x30 "RXICMP_GD_OCTETS,Number of bytes received in a good ICMP segment" line.long 0x34 "RXICMP_ERR_OCTETS,Number of bytes received in an ICMP segment with checksum errors" tree.end textline " " width 8. sif (cpu()=="MB86R12") group.long 0x700++0x37 line.long 0x00 "TSCR,Time Stamp Control Register" line.long 0x04 "SSIR,Sub-Second Increment Register" line.long 0x08 "STSR,System Time - Seconds Register" line.long 0x0C "STNR,System Time - Nanoseconds Register" line.long 0x10 "STSUR,System Time - Seconds Update Register" line.long 0x14 "STNUR,System Time - Nanoseconds Update Register" line.long 0x18 "TSAR,Time Stamp Addend Register" line.long 0x1C "TTSR,Target Time Seconds Register" line.long 0x20 "TTNR,Target Time Nanoseconds Register" line.long 0x24 "STHWSR,System Time - High Word Seconds Register" line.long 0x28 "TSR,Time Stamp Status Register" line.long 0x2C "PPSCR,PPC Control Register" line.long 0x30 "ATNR,Auxiliary Time Stamp-Nanosecond Register" line.long 0x34 "ATSR,Auxiliary Time Stamp-Seconds Register" endif if (15.<10.) group.long (0x800+0x0)++0x07 line.long 0x00 "MAR15H,MAC Address15 Register(High)" bitfld.long 0x00 31. " AE_15 ,Address15 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_15_47_32 ,MAC address15 [47:32]" line.long 0x04 "MAR15L,MAC Address15 Register(Low) [31:0]" else group.long (0x800+0x0)++0x07 line.long 0x00 "MAR15H,MAC Address15 Register(High)" bitfld.long 0x00 31. " AE_15 ,Address15 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_15_47_32 ,MAC address15 [47:32]" line.long 0x04 "MAR15L,MAC Address15 Register(Low) [31:0]" endif if (16.<10.) group.long (0x800+0x8)++0x07 line.long 0x00 "MAR16H,MAC Address16 Register(High)" bitfld.long 0x00 31. " AE_16 ,Address16 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_16_47_32 ,MAC address16 [47:32]" line.long 0x04 "MAR16L,MAC Address16 Register(Low) [31:0]" else group.long (0x800+0x8)++0x07 line.long 0x00 "MAR16H,MAC Address16 Register(High)" bitfld.long 0x00 31. " AE_16 ,Address16 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_16_47_32 ,MAC address16 [47:32]" line.long 0x04 "MAR16L,MAC Address16 Register(Low) [31:0]" endif if (17.<10.) group.long (0x800+0x10)++0x07 line.long 0x00 "MAR17H,MAC Address17 Register(High)" bitfld.long 0x00 31. " AE_17 ,Address17 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_17_47_32 ,MAC address17 [47:32]" line.long 0x04 "MAR17L,MAC Address17 Register(Low) [31:0]" else group.long (0x800+0x10)++0x07 line.long 0x00 "MAR17H,MAC Address17 Register(High)" bitfld.long 0x00 31. " AE_17 ,Address17 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_17_47_32 ,MAC address17 [47:32]" line.long 0x04 "MAR17L,MAC Address17 Register(Low) [31:0]" endif if (18.<10.) group.long (0x800+0x18)++0x07 line.long 0x00 "MAR18H,MAC Address18 Register(High)" bitfld.long 0x00 31. " AE_18 ,Address18 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_18_47_32 ,MAC address18 [47:32]" line.long 0x04 "MAR18L,MAC Address18 Register(Low) [31:0]" else group.long (0x800+0x18)++0x07 line.long 0x00 "MAR18H,MAC Address18 Register(High)" bitfld.long 0x00 31. " AE_18 ,Address18 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_18_47_32 ,MAC address18 [47:32]" line.long 0x04 "MAR18L,MAC Address18 Register(Low) [31:0]" endif if (19.<10.) group.long (0x800+0x20)++0x07 line.long 0x00 "MAR19H,MAC Address19 Register(High)" bitfld.long 0x00 31. " AE_19 ,Address19 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_19_47_32 ,MAC address19 [47:32]" line.long 0x04 "MAR19L,MAC Address19 Register(Low) [31:0]" else group.long (0x800+0x20)++0x07 line.long 0x00 "MAR19H,MAC Address19 Register(High)" bitfld.long 0x00 31. " AE_19 ,Address19 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_19_47_32 ,MAC address19 [47:32]" line.long 0x04 "MAR19L,MAC Address19 Register(Low) [31:0]" endif if (20.<10.) group.long (0x800+0x28)++0x07 line.long 0x00 "MAR20H,MAC Address20 Register(High)" bitfld.long 0x00 31. " AE_20 ,Address20 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_20_47_32 ,MAC address20 [47:32]" line.long 0x04 "MAR20L,MAC Address20 Register(Low) [31:0]" else group.long (0x800+0x28)++0x07 line.long 0x00 "MAR20H,MAC Address20 Register(High)" bitfld.long 0x00 31. " AE_20 ,Address20 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_20_47_32 ,MAC address20 [47:32]" line.long 0x04 "MAR20L,MAC Address20 Register(Low) [31:0]" endif if (21.<10.) group.long (0x800+0x30)++0x07 line.long 0x00 "MAR21H,MAC Address21 Register(High)" bitfld.long 0x00 31. " AE_21 ,Address21 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_21_47_32 ,MAC address21 [47:32]" line.long 0x04 "MAR21L,MAC Address21 Register(Low) [31:0]" else group.long (0x800+0x30)++0x07 line.long 0x00 "MAR21H,MAC Address21 Register(High)" bitfld.long 0x00 31. " AE_21 ,Address21 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_21_47_32 ,MAC address21 [47:32]" line.long 0x04 "MAR21L,MAC Address21 Register(Low) [31:0]" endif if (22.<10.) group.long (0x800+0x38)++0x07 line.long 0x00 "MAR22H,MAC Address22 Register(High)" bitfld.long 0x00 31. " AE_22 ,Address22 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_22_47_32 ,MAC address22 [47:32]" line.long 0x04 "MAR22L,MAC Address22 Register(Low) [31:0]" else group.long (0x800+0x38)++0x07 line.long 0x00 "MAR22H,MAC Address22 Register(High)" bitfld.long 0x00 31. " AE_22 ,Address22 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_22_47_32 ,MAC address22 [47:32]" line.long 0x04 "MAR22L,MAC Address22 Register(Low) [31:0]" endif if (23.<10.) group.long (0x800+0x40)++0x07 line.long 0x00 "MAR23H,MAC Address23 Register(High)" bitfld.long 0x00 31. " AE_23 ,Address23 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_23_47_32 ,MAC address23 [47:32]" line.long 0x04 "MAR23L,MAC Address23 Register(Low) [31:0]" else group.long (0x800+0x40)++0x07 line.long 0x00 "MAR23H,MAC Address23 Register(High)" bitfld.long 0x00 31. " AE_23 ,Address23 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_23_47_32 ,MAC address23 [47:32]" line.long 0x04 "MAR23L,MAC Address23 Register(Low) [31:0]" endif if (24.<10.) group.long (0x800+0x48)++0x07 line.long 0x00 "MAR24H,MAC Address24 Register(High)" bitfld.long 0x00 31. " AE_24 ,Address24 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_24_47_32 ,MAC address24 [47:32]" line.long 0x04 "MAR24L,MAC Address24 Register(Low) [31:0]" else group.long (0x800+0x48)++0x07 line.long 0x00 "MAR24H,MAC Address24 Register(High)" bitfld.long 0x00 31. " AE_24 ,Address24 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_24_47_32 ,MAC address24 [47:32]" line.long 0x04 "MAR24L,MAC Address24 Register(Low) [31:0]" endif if (25.<10.) group.long (0x800+0x50)++0x07 line.long 0x00 "MAR25H,MAC Address25 Register(High)" bitfld.long 0x00 31. " AE_25 ,Address25 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_25_47_32 ,MAC address25 [47:32]" line.long 0x04 "MAR25L,MAC Address25 Register(Low) [31:0]" else group.long (0x800+0x50)++0x07 line.long 0x00 "MAR25H,MAC Address25 Register(High)" bitfld.long 0x00 31. " AE_25 ,Address25 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_25_47_32 ,MAC address25 [47:32]" line.long 0x04 "MAR25L,MAC Address25 Register(Low) [31:0]" endif if (26.<10.) group.long (0x800+0x58)++0x07 line.long 0x00 "MAR26H,MAC Address26 Register(High)" bitfld.long 0x00 31. " AE_26 ,Address26 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_26_47_32 ,MAC address26 [47:32]" line.long 0x04 "MAR26L,MAC Address26 Register(Low) [31:0]" else group.long (0x800+0x58)++0x07 line.long 0x00 "MAR26H,MAC Address26 Register(High)" bitfld.long 0x00 31. " AE_26 ,Address26 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_26_47_32 ,MAC address26 [47:32]" line.long 0x04 "MAR26L,MAC Address26 Register(Low) [31:0]" endif if (27.<10.) group.long (0x800+0x60)++0x07 line.long 0x00 "MAR27H,MAC Address27 Register(High)" bitfld.long 0x00 31. " AE_27 ,Address27 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_27_47_32 ,MAC address27 [47:32]" line.long 0x04 "MAR27L,MAC Address27 Register(Low) [31:0]" else group.long (0x800+0x60)++0x07 line.long 0x00 "MAR27H,MAC Address27 Register(High)" bitfld.long 0x00 31. " AE_27 ,Address27 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_27_47_32 ,MAC address27 [47:32]" line.long 0x04 "MAR27L,MAC Address27 Register(Low) [31:0]" endif if (28.<10.) group.long (0x800+0x68)++0x07 line.long 0x00 "MAR28H,MAC Address28 Register(High)" bitfld.long 0x00 31. " AE_28 ,Address28 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_28_47_32 ,MAC address28 [47:32]" line.long 0x04 "MAR28L,MAC Address28 Register(Low) [31:0]" else group.long (0x800+0x68)++0x07 line.long 0x00 "MAR28H,MAC Address28 Register(High)" bitfld.long 0x00 31. " AE_28 ,Address28 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_28_47_32 ,MAC address28 [47:32]" line.long 0x04 "MAR28L,MAC Address28 Register(Low) [31:0]" endif if (29.<10.) group.long (0x800+0x70)++0x07 line.long 0x00 "MAR29H,MAC Address29 Register(High)" bitfld.long 0x00 31. " AE_29 ,Address29 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_29_47_32 ,MAC address29 [47:32]" line.long 0x04 "MAR29L,MAC Address29 Register(Low) [31:0]" else group.long (0x800+0x70)++0x07 line.long 0x00 "MAR29H,MAC Address29 Register(High)" bitfld.long 0x00 31. " AE_29 ,Address29 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_29_47_32 ,MAC address29 [47:32]" line.long 0x04 "MAR29L,MAC Address29 Register(Low) [31:0]" endif if (30.<10.) group.long (0x800+0x78)++0x07 line.long 0x00 "MAR30H,MAC Address30 Register(High)" bitfld.long 0x00 31. " AE_30 ,Address30 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_30_47_32 ,MAC address30 [47:32]" line.long 0x04 "MAR30L,MAC Address30 Register(Low) [31:0]" else group.long (0x800+0x78)++0x07 line.long 0x00 "MAR30H,MAC Address30 Register(High)" bitfld.long 0x00 31. " AE_30 ,Address30 enable" "Disabled,Enabled" bitfld.long 0x00 30. " SA ,Source Address" "DA fields,SA fields" hexmask.long.word 0x00 0.--15. 1. " A_30_47_32 ,MAC address30 [47:32]" line.long 0x04 "MAR30L,MAC Address30 Register(Low) [31:0]" endif if (((per.l(ad:0x38220000+0x1000))&0x8000002)==0x8000002) group.long 0x1000++0x03 line.long 0x00 "BMR,Bus Mode Register" bitfld.long 0x00 27. " TXPR ,Transmit Priority" "Normal,Higher" bitfld.long 0x00 26. " MB ,Mixed Burst" "Not set,Set" textline " " bitfld.long 0x00 25. " AAL ,Address-Aligned Beats" "Not generated,Generated" bitfld.long 0x00 24. " 8xPBL ,8xPBL Mode" "No multiplies,Multiplies" textline " " bitfld.long 0x00 23. " USP ,Use Separate PBL" "[13:8]bits,[22:17]bits" bitfld.long 0x00 17.--22. " RPBL ,These bits indicate the maximum number of beats to be transferred in one RxDMA transaction" "1,2,,4,,,,,8,,,,,,,,16,,,,,,,,,,,,,,,,32,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,," textline " " bitfld.long 0x00 16. " FB ,Fixed Burst" "Not performed,Performed" textline " " bitfld.long 0x00 8.--13. " PBL ,Programmable burst length" "1,2,,4,,,,,8,,,,,,,,16,,,,,,,,,,,,,,,,32,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,," bitfld.long 0x00 7. " ATDS ,Alternate Descriptor Size" "16 bytes(4 DWORDS),32bytes(8 DWORDS)" textline " " bitfld.long 0x00 2.--6. " DSL ,Descriptor skip length" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 1. " DA ,DMA Arbitration scheme" "Weighted Round-robin,Fixed priority" textline " " bitfld.long 0x00 0. " SWR ,Software Reset" "No reset,Reset" elif (((per.l(ad:0x38220000+0x1000))&0x8000002)==0x800000) group.long 0x1000++0x03 line.long 0x00 "BMR,Bus Mode Register" bitfld.long 0x00 27. " TXPR ,Transmit Priority" "Normal,Higher" bitfld.long 0x00 26. " MB ,Mixed Burst" "Not set,Set" textline " " bitfld.long 0x00 25. " AAL ,Address-Aligned Beats" "Not generated,Generated" bitfld.long 0x00 24. " 8xPBL ,8xPBL Mode" "No multiplies,Multiplies" textline " " bitfld.long 0x00 23. " USP ,Use Separate PBL" "[13:8]bits,[22:17]bits" bitfld.long 0x00 17.--22. " RPBL ,These bits indicate the maximum number of beats to be transferred in one RxDMA transaction" "1,2,,4,,,,,8,,,,,,,,16,,,,,,,,,,,,,,,,32,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,," textline " " bitfld.long 0x00 16. " FB ,Fixed Burst" "Not performed,Performed" bitfld.long 0x00 14.--15. " PR ,Rx:Tx priority ratio" "1:1,2:1,3:1,4:1" textline " " bitfld.long 0x00 8.--13. " PBL ,Programmable burst length" "1,2,,4,,,,,8,,,,,,,,16,,,,,,,,,,,,,,,,32,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,," bitfld.long 0x00 7. " ATDS ,Alternate Descriptor Size" "16 bytes(4 DWORDS),32bytes(8 DWORDS)" textline " " bitfld.long 0x00 2.--6. " DSL ,Descriptor skip length" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 1. " DA ,DMA Arbitration scheme" "Weighted Round-robin,Fixed priority" textline " " bitfld.long 0x00 0. " SWR ,Software Reset" "No reset,Reset" elif (((per.l(ad:0x38220000+0x1000))&0x8000002)==0x02) group.long 0x1000++0x03 line.long 0x00 "BMR,Bus Mode Register" bitfld.long 0x00 27. " TXPR ,Transmit Priority" "Normal,Higher" bitfld.long 0x00 26. " MB ,Mixed Burst" "Not set,Set" textline " " bitfld.long 0x00 25. " AAL ,Address-Aligned Beats" "Not generated,Generated" bitfld.long 0x00 24. " 8xPBL ,8xPBL Mode" "No multiplies,Multiplies" textline " " bitfld.long 0x00 23. " USP ,Use Separate PBL" "[13:8]bits,[22:17]bits" textline " " bitfld.long 0x00 16. " FB ,Fixed Burst" "Not performed,Performed" textline " " bitfld.long 0x00 8.--13. " PBL ,Programmable burst length" "1,2,,4,,,,,8,,,,,,,,16,,,,,,,,,,,,,,,,32,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,," bitfld.long 0x00 7. " ATDS ,Alternate Descriptor Size" "16 bytes(4 DWORDS),32bytes(8 DWORDS)" textline " " bitfld.long 0x00 2.--6. " DSL ,Descriptor skip length" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 1. " DA ,DMA Arbitration scheme" "Weighted Round-robin,Fixed priority" textline " " bitfld.long 0x00 0. " SWR ,Software Reset" "No reset,Reset" else group.long 0x1000++0x03 line.long 0x00 "BMR,Bus Mode Register" bitfld.long 0x00 27. " TXPR ,Transmit Priority" "Normal,Higher" bitfld.long 0x00 26. " MB ,Mixed Burst" "Not set,Set" textline " " bitfld.long 0x00 25. " AAL ,Address-Aligned Beats" "Not generated,Generated" bitfld.long 0x00 24. " 8xPBL ,8xPBL Mode" "No multiplies,Multiplies" textline " " bitfld.long 0x00 23. " USP ,Use Separate PBL" "[13:8]bits,[22:17]bits" textline " " bitfld.long 0x00 16. " FB ,Fixed Burst" "Not performed,Performed" bitfld.long 0x00 14.--15. " PR ,Rx:Tx priority ratio" "1:1,2:1,3:1,4:1" textline " " bitfld.long 0x00 8.--13. " PBL ,Programmable burst length" "1,2,,4,,,,,8,,,,,,,,16,,,,,,,,,,,,,,,,32,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,," bitfld.long 0x00 7. " ATDS ,Alternate Descriptor Size" "16 bytes(4 DWORDS),32bytes(8 DWORDS)" textline " " bitfld.long 0x00 2.--6. " DSL ,Descriptor skip length" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 1. " DA ,DMA Arbitration scheme" "Weighted Round-robin,Fixed priority" textline " " bitfld.long 0x00 0. " SWR ,Software Reset" "No reset,Reset" endif wgroup.long 0x1004++0x7 line.long 0x00 "TPDR,MDC Transmit Poll Demand Register" line.long 0x04 "RPDR,MDC Receive Poll Demand Register" group.long 0x100C++0x13 line.long 0x00 "RDLAR,MDC Receive Descriptor List Address Register" hexmask.long 0x00 2.--31. 0x04 " SRL ,Start of receive list" rbitfld.long 0x00 0.--1. " MZ , Must be Zero" "0,?..." line.long 0x04 "TDLAR,MDC Transmit Descriptor List Address Register" hexmask.long 0x04 2.--31. 0x04 " STL ,Start of transmit list" rbitfld.long 0x04 0.--1. " MZ , Must be Zero" "0,?..." line.long 0x08 "SR,MDC Status Register" rbitfld.long 0x08 30. " GLPII ,GMAC LPI Interrupt" "No interrupt,Interrupt" rbitfld.long 0x08 29. " TTI ,Time-Stamp Trigger Interrupt" "No interrupt,Interrupt" textline " " rbitfld.long 0x08 28. " GPI ,GMAC PMT Interrupt" "No interrupt,Interrupt" rbitfld.long 0x08 27. " GMI ,GMAC MMC Interrupt" "No interrupt,Interrupt" textline " " rbitfld.long 0x08 26. " GLI ,GMAC Line interface Interrupt" "No interrupt,Interrupt" rbitfld.long 0x08 25. " EB[2] ,Error Bits" "Data buffer,Descriptor" textline " " rbitfld.long 0x08 24. " EB[1] ,Error Bits" "Write,Read" rbitfld.long 0x08 23. " EB[0] ,Error Bits" "RxDMA,TxDMA" textline " " rbitfld.long 0x08 20.--22. " TS ,Transmit Process State" "R. or S. Trt. Cmd. issued,Fetching Trt. Transfer Desc.,Waiting for status,Reading the data from memory,Time-Stamp write state,,Suspended,Closing Transmit" rbitfld.long 0x08 17.--19. " RS ,Receive Process State" "Reset or stop,Fetching Descriptor,,Waiting for receive packet,Receive Descriptor Unavailable,Closing Receive Descriptor,Stamp write state,Transferring packet to host" textline " " eventfld.long 0x08 16. " NIS ,Normal Interrupt Summary" "No interrupt,Interrupt" eventfld.long 0x08 15. " AIS ,Abnormal Interrupt Summary" "No interrupt,Interrupt" textline " " eventfld.long 0x08 14. " ERI ,Early Receive Interrupt" "No interrupt,Interrupt" eventfld.long 0x08 13. " FBI ,Fatal Bus Error Interrupt" "Not occur,Occur" textline " " eventfld.long 0x08 10. " ETI ,Early Transmit Interrupt" "No interrupt,Interrupt" eventfld.long 0x08 9. " RWT ,Receive Watchdog Timeout" "Less than 2.048,Greater than 2.048" textline " " eventfld.long 0x08 8. " RPS ,Receive process Stopped" "No,Yes" eventfld.long 0x08 7. " RU ,Receive Buffer Unavailable" "No,Yes" textline " " eventfld.long 0x08 6. " RI ,Receive Interrupt" "No interrupt,Interrupt" eventfld.long 0x08 5. " UNF ,Transmit underflow" "No,Yes" textline " " eventfld.long 0x08 4. " OVF ,Receive Overflow" "No,Yes" eventfld.long 0x08 3. " TJT ,Transmit Jabber Timeout" "Not timeout,Timeout" textline " " eventfld.long 0x08 2. " TU ,Transmit Buffer Unavailable" "No,Yes" eventfld.long 0x08 1. " TPS ,Transmit Process Stopped" "Not stopped,Stopped" textline " " eventfld.long 0x08 0. " TI ,This bit indicates that frame transmission is finished and TDES1[31] is set in the First Descriptor" "No,Yes" line.long 0x0C "OMR,MDC Operation Mode Register" bitfld.long 0x0C 26. " DT ,Disable Dropping of TCP/IP Checksum Error Frames" "No,Yes" bitfld.long 0x0C 25. " RSF ,Receive Store and Forward" "Read mode,Operated mode" textline " " bitfld.long 0x0C 24. " DFF ,Disable Flushing of Received Frames" "No,Yes" bitfld.long 0x0C 21. " TSF ,Transmit Store Forward" "Disabled,Enabled" textline " " bitfld.long 0x0C 20. " FTF ,Flush Transmit FIFO" "No reset,Reset" bitfld.long 0x0C 14.--16. " TTC ,Transmit threshhold control" "64Bytes,128Bytes,192Bytes,256Bytes,40Bytes,32Bytes,24Bytes,16Bytes" textline " " bitfld.long 0x0C 13. " ST ,Start/Stop transmission command" "Stopped,Running" bitfld.long 0x0C 7. " FEF ,Forward Error Frames" "Drops frames with error,Error forwarded" textline " " bitfld.long 0x0C 6. " FUF ,Forward Undersized Good Frames" "Not set,Set" bitfld.long 0x0C 3.--4. " RTC ,Receive Threshold Control" "64,32,96,128" textline " " bitfld.long 0x0C 2. " OSF ,Operate on second frame" "Disabled,Enabled" bitfld.long 0x0C 1. " SR ,Start/Stop receive" "Stopped,Started" line.long 0x10 "IER,MDC Interrupt Enable Register" bitfld.long 0x10 16. " NIE ,Normal interrupt summary" "Disabled,Enabled" textline " " bitfld.long 0x10 15. " AIE ,Abnormal interrupt summary" "Disabled,Enabled" bitfld.long 0x10 14. " ERE ,Early receive interrupt" "Disabled,Enabled" textline " " bitfld.long 0x10 13. " FBE ,Fatal bus error" "Disabled,Enabled" bitfld.long 0x10 10. " ETE ,Early transmit interrupt" "Disabled,Enabled" textline " " bitfld.long 0x10 9. " RWE ,Receive watchdog timeout" "Disabled,Enabled" bitfld.long 0x10 8. " RSE ,Receive Process stopped" "Disabled,Enabled" textline " " bitfld.long 0x10 7. " RUE ,Receive buffer unavailable" "Disabled,Enabled" bitfld.long 0x10 6. " RIE ,Receive interrupt" "Disabled,Enabled" textline " " bitfld.long 0x10 5. " UNE ,Transmit underflow" "Disabled,Enabled" bitfld.long 0x10 4. " OVE ,Receive overflow" "Disabled,Enabled" textline " " bitfld.long 0x10 3. " TJE ,Transmit jabber timeout" "Disabled,Enabled" bitfld.long 0x10 2. " TUE ,Transmit buffer unavailable" "Disabled,Enabled" textline " " bitfld.long 0x10 1. " TSE ,Transmit process stopped" "Disabled,Enabled" bitfld.long 0x10 0. " TIE ,Transmit interrupt" "Disabled,Enabled" rgroup.long 0x1020++0x03 line.long 0x00 "MFC,MDC Missed Frame Register" bitfld.long 0x00 28. " ONMFF ,Overflow NMFF" "Not overflowed,Overflowed" hexmask.long.word 0x00 17.--27. 1. " NMFF ,Number of missed freames by F_GMAC4" textline " " bitfld.long 0x00 16. " ONMFH ,Overflow NMFH" "Not overflowed,Overflowed" hexmask.long.word 0x00 0.--15. 1. " NMFH ,Number of missed frames by HOST" group.long 0x1024++0x03 line.long 0x00 "RIWTR,Receive interrupt Watchdog Timer Register" hexmask.long.byte 0x00 0.--7. 1. " RIWT ,RI Watchdog Timer count" rgroup.long 0x102C++0x03 line.long 0x00 "AHBSR,AHB status register" bitfld.long 0x00 0. " AHBS ,It indicates that the AHB master interface FSMs are in the non-idle state" "No,Yes" rgroup.long 0x1048++0x07 line.long 0x00 "CHTDR,Current Host Transmit Descriptor register" line.long 0x04 "CHRDR,Current Host Receive Descriptor register" rgroup.long 0x1050++0x7 line.long 0x00 "CHTBAR,MDC Current Host Transmit Buffer Address Register" line.long 0x04 "CHRBAR,MDC Current Host Receive Buffer Address Register" width 0x0B tree.end tree "TCON (Timing Controller)" base ad:0x28000000 width 18. tree "The 64 Sequencer Position Definition registers" group.long 0x0++0x03 line.long 0x00 "DIR_SSQCNTS0,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_0 ,SSQCNTS_FIELD0" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x4++0x03 line.long 0x00 "DIR_SSQCNTS1,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_1 ,SSQCNTS_FIELD1" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x8++0x03 line.long 0x00 "DIR_SSQCNTS2,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_2 ,SSQCNTS_FIELD2" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xC++0x03 line.long 0x00 "DIR_SSQCNTS3,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_3 ,SSQCNTS_FIELD3" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x10++0x03 line.long 0x00 "DIR_SSQCNTS4,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_4 ,SSQCNTS_FIELD4" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x14++0x03 line.long 0x00 "DIR_SSQCNTS5,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_5 ,SSQCNTS_FIELD5" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x18++0x03 line.long 0x00 "DIR_SSQCNTS6,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_6 ,SSQCNTS_FIELD6" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x1C++0x03 line.long 0x00 "DIR_SSQCNTS7,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_7 ,SSQCNTS_FIELD7" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x20++0x03 line.long 0x00 "DIR_SSQCNTS8,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_8 ,SSQCNTS_FIELD8" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x24++0x03 line.long 0x00 "DIR_SSQCNTS9,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_9 ,SSQCNTS_FIELD9" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x28++0x03 line.long 0x00 "DIR_SSQCNTS10,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_10 ,SSQCNTS_FIELD10" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x2C++0x03 line.long 0x00 "DIR_SSQCNTS11,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_11 ,SSQCNTS_FIELD11" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x30++0x03 line.long 0x00 "DIR_SSQCNTS12,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_12 ,SSQCNTS_FIELD12" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x34++0x03 line.long 0x00 "DIR_SSQCNTS13,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_13 ,SSQCNTS_FIELD13" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x38++0x03 line.long 0x00 "DIR_SSQCNTS14,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_14 ,SSQCNTS_FIELD14" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x3C++0x03 line.long 0x00 "DIR_SSQCNTS15,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_15 ,SSQCNTS_FIELD15" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x40++0x03 line.long 0x00 "DIR_SSQCNTS16,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_16 ,SSQCNTS_FIELD16" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x44++0x03 line.long 0x00 "DIR_SSQCNTS17,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_17 ,SSQCNTS_FIELD17" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x48++0x03 line.long 0x00 "DIR_SSQCNTS18,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_18 ,SSQCNTS_FIELD18" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x4C++0x03 line.long 0x00 "DIR_SSQCNTS19,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_19 ,SSQCNTS_FIELD19" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x50++0x03 line.long 0x00 "DIR_SSQCNTS20,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_20 ,SSQCNTS_FIELD20" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x54++0x03 line.long 0x00 "DIR_SSQCNTS21,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_21 ,SSQCNTS_FIELD21" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x58++0x03 line.long 0x00 "DIR_SSQCNTS22,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_22 ,SSQCNTS_FIELD22" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x5C++0x03 line.long 0x00 "DIR_SSQCNTS23,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_23 ,SSQCNTS_FIELD23" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x60++0x03 line.long 0x00 "DIR_SSQCNTS24,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_24 ,SSQCNTS_FIELD24" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x64++0x03 line.long 0x00 "DIR_SSQCNTS25,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_25 ,SSQCNTS_FIELD25" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x68++0x03 line.long 0x00 "DIR_SSQCNTS26,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_26 ,SSQCNTS_FIELD26" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x6C++0x03 line.long 0x00 "DIR_SSQCNTS27,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_27 ,SSQCNTS_FIELD27" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x70++0x03 line.long 0x00 "DIR_SSQCNTS28,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_28 ,SSQCNTS_FIELD28" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x74++0x03 line.long 0x00 "DIR_SSQCNTS29,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_29 ,SSQCNTS_FIELD29" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x78++0x03 line.long 0x00 "DIR_SSQCNTS30,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_30 ,SSQCNTS_FIELD30" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x7C++0x03 line.long 0x00 "DIR_SSQCNTS31,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_31 ,SSQCNTS_FIELD31" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x80++0x03 line.long 0x00 "DIR_SSQCNTS32,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_32 ,SSQCNTS_FIELD32" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x84++0x03 line.long 0x00 "DIR_SSQCNTS33,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_33 ,SSQCNTS_FIELD33" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x88++0x03 line.long 0x00 "DIR_SSQCNTS34,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_34 ,SSQCNTS_FIELD34" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x8C++0x03 line.long 0x00 "DIR_SSQCNTS35,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_35 ,SSQCNTS_FIELD35" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x90++0x03 line.long 0x00 "DIR_SSQCNTS36,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_36 ,SSQCNTS_FIELD36" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x94++0x03 line.long 0x00 "DIR_SSQCNTS37,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_37 ,SSQCNTS_FIELD37" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x98++0x03 line.long 0x00 "DIR_SSQCNTS38,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_38 ,SSQCNTS_FIELD38" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0x9C++0x03 line.long 0x00 "DIR_SSQCNTS39,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_39 ,SSQCNTS_FIELD39" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xA0++0x03 line.long 0x00 "DIR_SSQCNTS40,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_40 ,SSQCNTS_FIELD40" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xA4++0x03 line.long 0x00 "DIR_SSQCNTS41,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_41 ,SSQCNTS_FIELD41" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xA8++0x03 line.long 0x00 "DIR_SSQCNTS42,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_42 ,SSQCNTS_FIELD42" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xAC++0x03 line.long 0x00 "DIR_SSQCNTS43,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_43 ,SSQCNTS_FIELD43" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xB0++0x03 line.long 0x00 "DIR_SSQCNTS44,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_44 ,SSQCNTS_FIELD44" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xB4++0x03 line.long 0x00 "DIR_SSQCNTS45,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_45 ,SSQCNTS_FIELD45" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xB8++0x03 line.long 0x00 "DIR_SSQCNTS46,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_46 ,SSQCNTS_FIELD46" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xBC++0x03 line.long 0x00 "DIR_SSQCNTS47,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_47 ,SSQCNTS_FIELD47" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xC0++0x03 line.long 0x00 "DIR_SSQCNTS48,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_48 ,SSQCNTS_FIELD48" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xC4++0x03 line.long 0x00 "DIR_SSQCNTS49,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_49 ,SSQCNTS_FIELD49" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xC8++0x03 line.long 0x00 "DIR_SSQCNTS50,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_50 ,SSQCNTS_FIELD50" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xCC++0x03 line.long 0x00 "DIR_SSQCNTS51,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_51 ,SSQCNTS_FIELD51" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xD0++0x03 line.long 0x00 "DIR_SSQCNTS52,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_52 ,SSQCNTS_FIELD52" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xD4++0x03 line.long 0x00 "DIR_SSQCNTS53,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_53 ,SSQCNTS_FIELD53" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xD8++0x03 line.long 0x00 "DIR_SSQCNTS54,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_54 ,SSQCNTS_FIELD54" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xDC++0x03 line.long 0x00 "DIR_SSQCNTS55,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_55 ,SSQCNTS_FIELD55" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xE0++0x03 line.long 0x00 "DIR_SSQCNTS56,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_56 ,SSQCNTS_FIELD56" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xE4++0x03 line.long 0x00 "DIR_SSQCNTS57,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_57 ,SSQCNTS_FIELD57" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xE8++0x03 line.long 0x00 "DIR_SSQCNTS58,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_58 ,SSQCNTS_FIELD58" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xEC++0x03 line.long 0x00 "DIR_SSQCNTS59,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_59 ,SSQCNTS_FIELD59" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xF0++0x03 line.long 0x00 "DIR_SSQCNTS60,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_60 ,SSQCNTS_FIELD60" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xF4++0x03 line.long 0x00 "DIR_SSQCNTS61,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_61 ,SSQCNTS_FIELD61" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xF8++0x03 line.long 0x00 "DIR_SSQCNTS62,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_62 ,SSQCNTS_FIELD62" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif group.long 0xFC++0x03 line.long 0x00 "DIR_SSQCNTS63,Sequencer Position Definition register define the X/Y scan positions of the sequencers" bitfld.long 0x00 31. " SSQCNTS_OUT ,This bit holds the value (0 1) to be output when the X/Y scan position is reached" "0,1" hexmask.long.word 0x00 16.--30. 1. " SSQCNTS_SEQX ,X scan position" sif (cpuis("MB86R11F")) bitfld.long 0x00 15. " SSQCNTS_63 ,SSQCNTS_FIELD63" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SSQCNTS_SEQY ,Y scan position" endif tree.end width 18. textline " " group.long 0x400++0x03 line.long 0x00 "DIR_SWRESET,TCON Software Reset" bitfld.long 0x00 0. " SWRESET ,Software reset R/W" "No active/No effect,Active/Reset" if (0.<10.) group.long 0x404++0x0F line.long 0x00 "DIR_SPG0POSON,Sync pulse generator 0" bitfld.long 0x00 31. " SPGPSON_TOGGLE0 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X0 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_0 ,SPGPSON_FIELD0" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y0 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y0 ,Y scan position" endif line.long 0x04 "DIR_SPG0MASKON,Sequencer Pulse Generator 0 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG0POSOFF,Sync pulse generator 0" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE0 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X0 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_0 ,SPGPSOFF_FIELD0" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y0 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y0 ,Y scan position" endif line.long 0x0C "DIR_SPG0MASKOFF,Sequencer Pulse Generator 0 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" else group.long 0x404++0x0F line.long 0x00 "DIR_SPG0POSON,Sync pulse generator 0" bitfld.long 0x00 31. " SPGPSON_TOGGLE0 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X0 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_0 ,SPGPSON_FIELD0" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y0 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y0 ,Y scan position" endif line.long 0x04 "DIR_SPG0MASKON,Sequencer Pulse Generator 0 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG0POSOFF,Sync pulse generator 0" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE0 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X0 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_0 ,SPGPSOFF_FIELD0" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y0 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y0 ,Y scan position" endif line.long 0x0C "DIR_SPG0MASKOFF,Sequencer Pulse Generator 0 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" endif if (1.<10.) group.long 0x414++0x0F line.long 0x00 "DIR_SPG1POSON,Sync pulse generator 1" bitfld.long 0x00 31. " SPGPSON_TOGGLE1 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X1 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_1 ,SPGPSON_FIELD1" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y1 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y1 ,Y scan position" endif line.long 0x04 "DIR_SPG1MASKON,Sequencer Pulse Generator 1 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG1POSOFF,Sync pulse generator 1" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE1 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X1 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_1 ,SPGPSOFF_FIELD1" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y1 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y1 ,Y scan position" endif line.long 0x0C "DIR_SPG1MASKOFF,Sequencer Pulse Generator 1 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" else group.long 0x414++0x0F line.long 0x00 "DIR_SPG1POSON,Sync pulse generator 1" bitfld.long 0x00 31. " SPGPSON_TOGGLE1 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X1 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_1 ,SPGPSON_FIELD1" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y1 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y1 ,Y scan position" endif line.long 0x04 "DIR_SPG1MASKON,Sequencer Pulse Generator 1 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG1POSOFF,Sync pulse generator 1" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE1 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X1 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_1 ,SPGPSOFF_FIELD1" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y1 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y1 ,Y scan position" endif line.long 0x0C "DIR_SPG1MASKOFF,Sequencer Pulse Generator 1 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" endif if (2.<10.) group.long 0x424++0x0F line.long 0x00 "DIR_SPG2POSON,Sync pulse generator 2" bitfld.long 0x00 31. " SPGPSON_TOGGLE2 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X2 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_2 ,SPGPSON_FIELD2" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y2 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y2 ,Y scan position" endif line.long 0x04 "DIR_SPG2MASKON,Sequencer Pulse Generator 2 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG2POSOFF,Sync pulse generator 2" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE2 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X2 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_2 ,SPGPSOFF_FIELD2" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y2 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y2 ,Y scan position" endif line.long 0x0C "DIR_SPG2MASKOFF,Sequencer Pulse Generator 2 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" else group.long 0x424++0x0F line.long 0x00 "DIR_SPG2POSON,Sync pulse generator 2" bitfld.long 0x00 31. " SPGPSON_TOGGLE2 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X2 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_2 ,SPGPSON_FIELD2" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y2 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y2 ,Y scan position" endif line.long 0x04 "DIR_SPG2MASKON,Sequencer Pulse Generator 2 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG2POSOFF,Sync pulse generator 2" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE2 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X2 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_2 ,SPGPSOFF_FIELD2" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y2 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y2 ,Y scan position" endif line.long 0x0C "DIR_SPG2MASKOFF,Sequencer Pulse Generator 2 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" endif if (3.<10.) group.long 0x434++0x0F line.long 0x00 "DIR_SPG3POSON,Sync pulse generator 3" bitfld.long 0x00 31. " SPGPSON_TOGGLE3 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X3 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_3 ,SPGPSON_FIELD3" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y3 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y3 ,Y scan position" endif line.long 0x04 "DIR_SPG3MASKON,Sequencer Pulse Generator 3 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG3POSOFF,Sync pulse generator 3" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE3 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X3 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_3 ,SPGPSOFF_FIELD3" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y3 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y3 ,Y scan position" endif line.long 0x0C "DIR_SPG3MASKOFF,Sequencer Pulse Generator 3 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" else group.long 0x434++0x0F line.long 0x00 "DIR_SPG3POSON,Sync pulse generator 3" bitfld.long 0x00 31. " SPGPSON_TOGGLE3 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X3 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_3 ,SPGPSON_FIELD3" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y3 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y3 ,Y scan position" endif line.long 0x04 "DIR_SPG3MASKON,Sequencer Pulse Generator 3 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG3POSOFF,Sync pulse generator 3" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE3 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X3 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_3 ,SPGPSOFF_FIELD3" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y3 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y3 ,Y scan position" endif line.long 0x0C "DIR_SPG3MASKOFF,Sequencer Pulse Generator 3 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" endif if (4.<10.) group.long 0x444++0x0F line.long 0x00 "DIR_SPG4POSON,Sync pulse generator 4" bitfld.long 0x00 31. " SPGPSON_TOGGLE4 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X4 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_4 ,SPGPSON_FIELD4" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y4 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y4 ,Y scan position" endif line.long 0x04 "DIR_SPG4MASKON,Sequencer Pulse Generator 4 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG4POSOFF,Sync pulse generator 4" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE4 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X4 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_4 ,SPGPSOFF_FIELD4" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y4 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y4 ,Y scan position" endif line.long 0x0C "DIR_SPG4MASKOFF,Sequencer Pulse Generator 4 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" else group.long 0x444++0x0F line.long 0x00 "DIR_SPG4POSON,Sync pulse generator 4" bitfld.long 0x00 31. " SPGPSON_TOGGLE4 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X4 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_4 ,SPGPSON_FIELD4" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y4 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y4 ,Y scan position" endif line.long 0x04 "DIR_SPG4MASKON,Sequencer Pulse Generator 4 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG4POSOFF,Sync pulse generator 4" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE4 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X4 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_4 ,SPGPSOFF_FIELD4" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y4 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y4 ,Y scan position" endif line.long 0x0C "DIR_SPG4MASKOFF,Sequencer Pulse Generator 4 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" endif if (5.<10.) group.long 0x454++0x0F line.long 0x00 "DIR_SPG5POSON,Sync pulse generator 5" bitfld.long 0x00 31. " SPGPSON_TOGGLE5 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X5 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_5 ,SPGPSON_FIELD5" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y5 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y5 ,Y scan position" endif line.long 0x04 "DIR_SPG5MASKON,Sequencer Pulse Generator 5 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG5POSOFF,Sync pulse generator 5" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE5 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X5 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_5 ,SPGPSOFF_FIELD5" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y5 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y5 ,Y scan position" endif line.long 0x0C "DIR_SPG5MASKOFF,Sequencer Pulse Generator 5 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" else group.long 0x454++0x0F line.long 0x00 "DIR_SPG5POSON,Sync pulse generator 5" bitfld.long 0x00 31. " SPGPSON_TOGGLE5 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X5 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_5 ,SPGPSON_FIELD5" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y5 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y5 ,Y scan position" endif line.long 0x04 "DIR_SPG5MASKON,Sequencer Pulse Generator 5 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG5POSOFF,Sync pulse generator 5" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE5 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X5 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_5 ,SPGPSOFF_FIELD5" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y5 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y5 ,Y scan position" endif line.long 0x0C "DIR_SPG5MASKOFF,Sequencer Pulse Generator 5 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" endif if (6.<10.) group.long 0x464++0x0F line.long 0x00 "DIR_SPG6POSON,Sync pulse generator 6" bitfld.long 0x00 31. " SPGPSON_TOGGLE6 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X6 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_6 ,SPGPSON_FIELD6" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y6 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y6 ,Y scan position" endif line.long 0x04 "DIR_SPG6MASKON,Sequencer Pulse Generator 6 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG6POSOFF,Sync pulse generator 6" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE6 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X6 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_6 ,SPGPSOFF_FIELD6" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y6 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y6 ,Y scan position" endif line.long 0x0C "DIR_SPG6MASKOFF,Sequencer Pulse Generator 6 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" else group.long 0x464++0x0F line.long 0x00 "DIR_SPG6POSON,Sync pulse generator 6" bitfld.long 0x00 31. " SPGPSON_TOGGLE6 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X6 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_6 ,SPGPSON_FIELD6" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y6 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y6 ,Y scan position" endif line.long 0x04 "DIR_SPG6MASKON,Sequencer Pulse Generator 6 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG6POSOFF,Sync pulse generator 6" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE6 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X6 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_6 ,SPGPSOFF_FIELD6" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y6 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y6 ,Y scan position" endif line.long 0x0C "DIR_SPG6MASKOFF,Sequencer Pulse Generator 6 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" endif if (7.<10.) group.long 0x474++0x0F line.long 0x00 "DIR_SPG7POSON,Sync pulse generator 7" bitfld.long 0x00 31. " SPGPSON_TOGGLE7 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X7 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_7 ,SPGPSON_FIELD7" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y7 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y7 ,Y scan position" endif line.long 0x04 "DIR_SPG7MASKON,Sequencer Pulse Generator 7 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG7POSOFF,Sync pulse generator 7" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE7 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X7 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_7 ,SPGPSOFF_FIELD7" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y7 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y7 ,Y scan position" endif line.long 0x0C "DIR_SPG7MASKOFF,Sequencer Pulse Generator 7 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" else group.long 0x474++0x0F line.long 0x00 "DIR_SPG7POSON,Sync pulse generator 7" bitfld.long 0x00 31. " SPGPSON_TOGGLE7 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X7 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_7 ,SPGPSON_FIELD7" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y7 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y7 ,Y scan position" endif line.long 0x04 "DIR_SPG7MASKON,Sequencer Pulse Generator 7 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG7POSOFF,Sync pulse generator 7" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE7 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X7 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_7 ,SPGPSOFF_FIELD7" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y7 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y7 ,Y scan position" endif line.long 0x0C "DIR_SPG7MASKOFF,Sequencer Pulse Generator 7 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" endif if (8.<10.) group.long 0x484++0x0F line.long 0x00 "DIR_SPG8POSON,Sync pulse generator 8" bitfld.long 0x00 31. " SPGPSON_TOGGLE8 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X8 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_8 ,SPGPSON_FIELD8" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y8 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y8 ,Y scan position" endif line.long 0x04 "DIR_SPG8MASKON,Sequencer Pulse Generator 8 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG8POSOFF,Sync pulse generator 8" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE8 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X8 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_8 ,SPGPSOFF_FIELD8" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y8 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y8 ,Y scan position" endif line.long 0x0C "DIR_SPG8MASKOFF,Sequencer Pulse Generator 8 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" else group.long 0x484++0x0F line.long 0x00 "DIR_SPG8POSON,Sync pulse generator 8" bitfld.long 0x00 31. " SPGPSON_TOGGLE8 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X8 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_8 ,SPGPSON_FIELD8" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y8 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y8 ,Y scan position" endif line.long 0x04 "DIR_SPG8MASKON,Sequencer Pulse Generator 8 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG8POSOFF,Sync pulse generator 8" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE8 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X8 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_8 ,SPGPSOFF_FIELD8" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y8 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y8 ,Y scan position" endif line.long 0x0C "DIR_SPG8MASKOFF,Sequencer Pulse Generator 8 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" endif if (9.<10.) group.long 0x494++0x0F line.long 0x00 "DIR_SPG9POSON,Sync pulse generator 9" bitfld.long 0x00 31. " SPGPSON_TOGGLE9 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X9 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_9 ,SPGPSON_FIELD9" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y9 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y9 ,Y scan position" endif line.long 0x04 "DIR_SPG9MASKON,Sequencer Pulse Generator 9 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG9POSOFF,Sync pulse generator 9" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE9 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X9 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_9 ,SPGPSOFF_FIELD9" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y9 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y9 ,Y scan position" endif line.long 0x0C "DIR_SPG9MASKOFF,Sequencer Pulse Generator 9 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" else group.long 0x494++0x0F line.long 0x00 "DIR_SPG9POSON,Sync pulse generator 9" bitfld.long 0x00 31. " SPGPSON_TOGGLE9 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X9 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_9 ,SPGPSON_FIELD9" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y9 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y9 ,Y scan position" endif line.long 0x04 "DIR_SPG9MASKON,Sequencer Pulse Generator 9 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG9POSOFF,Sync pulse generator 9" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE9 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X9 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_9 ,SPGPSOFF_FIELD9" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y9 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y9 ,Y scan position" endif line.long 0x0C "DIR_SPG9MASKOFF,Sequencer Pulse Generator 9 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" endif if (10.<10.) group.long 0x4A4++0x0F line.long 0x00 "DIR_SPG10POSON,Sync pulse generator 10" bitfld.long 0x00 31. " SPGPSON_TOGGLE10 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X10 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_10 ,SPGPSON_FIELD10" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y10 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y10 ,Y scan position" endif line.long 0x04 "DIR_SPG10MASKON,Sequencer Pulse Generator 10 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG10POSOFF,Sync pulse generator 10" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE10 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X10 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_10 ,SPGPSOFF_FIELD10" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y10 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y10 ,Y scan position" endif line.long 0x0C "DIR_SPG10MASKOFF,Sequencer Pulse Generator 10 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" else group.long 0x4A4++0x0F line.long 0x00 "DIR_SPG10POSON,Sync pulse generator 10" bitfld.long 0x00 31. " SPGPSON_TOGGLE10 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X10 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_10 ,SPGPSON_FIELD10" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y10 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y10 ,Y scan position" endif line.long 0x04 "DIR_SPG10MASKON,Sequencer Pulse Generator 10 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG10POSOFF,Sync pulse generator 10" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE10 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X10 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_10 ,SPGPSOFF_FIELD10" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y10 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y10 ,Y scan position" endif line.long 0x0C "DIR_SPG10MASKOFF,Sequencer Pulse Generator 10 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" endif if (11.<10.) group.long 0x4B4++0x0F line.long 0x00 "DIR_SPG11POSON,Sync pulse generator 11" bitfld.long 0x00 31. " SPGPSON_TOGGLE11 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X11 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_11 ,SPGPSON_FIELD11" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y11 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y11 ,Y scan position" endif line.long 0x04 "DIR_SPG11MASKON,Sequencer Pulse Generator 11 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG11POSOFF,Sync pulse generator 11" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE11 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X11 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_11 ,SPGPSOFF_FIELD11" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y11 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y11 ,Y scan position" endif line.long 0x0C "DIR_SPG11MASKOFF,Sequencer Pulse Generator 11 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" else group.long 0x4B4++0x0F line.long 0x00 "DIR_SPG11POSON,Sync pulse generator 11" bitfld.long 0x00 31. " SPGPSON_TOGGLE11 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x00 16.--31. 1. " SPGPSON_X11 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x00 15. " SPGPSON_11 ,SPGPSON_FIELD11" "Odd field,Even field" hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y11 ,Y scan position" else hexmask.long.word 0x00 0.--14. 1. " SPGPSON_Y11 ,Y scan position" endif line.long 0x04 "DIR_SPG11MASKON,Sequencer Pulse Generator 11 Mask Enable" bitfld.long 0x04 30. " SPGMKON30 ,Mask bit" "Include,Do not include" bitfld.long 0x04 29. " SPGMKON29 ,Mask bit" "Include,Do not include" bitfld.long 0x04 28. " SPGMKON28 ,Mask bit" "Include,Do not include" bitfld.long 0x04 27. " SPGMKON27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 26. " SPGMKON26 ,Mask bit" "Include,Do not include" bitfld.long 0x04 25. " SPGMKON25 ,Mask bit" "Include,Do not include" bitfld.long 0x04 24. " SPGMKON24 ,Mask bit" "Include,Do not include" bitfld.long 0x04 23. " SPGMKON23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 22. " SPGMKON22 ,Mask bit" "Include,Do not include" bitfld.long 0x04 21. " SPGMKON21 ,Mask bit" "Include,Do not include" bitfld.long 0x04 20. " SPGMKON20 ,Mask bit" "Include,Do not include" bitfld.long 0x04 19. " SPGMKON19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 18. " SPGMKON18 ,Mask bit" "Include,Do not include" bitfld.long 0x04 17. " SPGMKON17 ,Mask bit" "Include,Do not include" bitfld.long 0x04 16. " SPGMKON16 ,Mask bit" "Include,Do not include" bitfld.long 0x04 15. " SPGMKON15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 14. " SPGMKON14 ,Mask bit" "Include,Do not include" bitfld.long 0x04 13. " SPGMKON13 ,Mask bit" "Include,Do not include" bitfld.long 0x04 12. " SPGMKON12 ,Mask bit" "Include,Do not include" bitfld.long 0x04 11. " SPGMKON11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 10. " SPGMKON10 ,Mask bit" "Include,Do not include" bitfld.long 0x04 9. " SPGMKON9 ,Mask bit" "Include,Do not include" bitfld.long 0x04 8. " SPGMKON8 ,Mask bit" "Include,Do not include" bitfld.long 0x04 7. " SPGMKON7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 6. " SPGMKON6 ,Mask bit" "Include,Do not include" bitfld.long 0x04 5. " SPGMKON5 ,Mask bit" "Include,Do not include" bitfld.long 0x04 4. " SPGMKON4 ,Mask bit" "Include,Do not include" bitfld.long 0x04 3. " SPGMKON3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x04 2. " SPGMKON2 ,Mask bit" "Include,Do not include" bitfld.long 0x04 1. " SPGMKON1 ,Mask bit" "Include,Do not include" bitfld.long 0x04 0. " SPGMKON0 ,Mask bit" "Include,Do not include" line.long 0x08 "DIR_SPG11POSOFF,Sync pulse generator 11" bitfld.long 0x08 31. " SPGPSOFF_TOGGLE11 ,Toggle bit" "Disabled,Enabled" hexmask.long.word 0x08 16.--30. 1. " SPGPSOFF_X11 ,X scan position" sif (cpu()=="MB86R11F") bitfld.long 0x08 15. " SPGPSOFF_11 ,SPGPSOFF_FIELD11" "Odd field,Even field" hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y11 ,Y scan position" else hexmask.long.word 0x08 0.--14. 1. " SPGPSOFF_Y11 ,Y scan position" endif line.long 0x0C "DIR_SPG11MASKOFF,Sequencer Pulse Generator 11 Mask Enable" bitfld.long 0x0C 30. " SPGMKOFF30 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 29. " SPGMKOFF29 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 28. " SPGMKOFF28 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 27. " SPGMKOFF27 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 26. " SPGMKOFF26 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 25. " SPGMKOFF25 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 24. " SPGMKOFF24 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 23. " SPGMKOFF23 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 22. " SPGMKOFF22 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 21. " SPGMKOFF21 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 20. " SPGMKOFF20 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 19. " SPGMKOFF19 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 18. " SPGMKOFF18 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 17. " SPGMKOFF17 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 16. " SPGMKOFF16 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 15. " SPGMKOFF15 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 14. " SPGMKOFF14 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 13. " SPGMKOFF13 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 12. " SPGMKOFF12 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 11. " SPGMKOFF11 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 10. " SPGMKOFF10 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 9. " SPGMKOFF9 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 8. " SPGMKOFF8 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 7. " SPGMKOFF7 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 6. " SPGMKOFF6 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 5. " SPGMKOFF5 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 4. " SPGMKOFF4 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 3. " SPGMKOFF3 ,Mask bit" "Include,Do not include" textline " " bitfld.long 0x0C 2. " SPGMKOFF2 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 1. " SPGMKOFF1 ,Mask bit" "Include,Do not include" bitfld.long 0x0C 0. " SPGMKOFF0 ,Mask bit" "Include,Do not include" endif group.long 0x4C4++0x03 line.long 0x00 "DIR_SSQCYCLE,Sets the sequencer cycle length" bitfld.long 0x0 0.--5. " SSQCYCLE ,Sequencer cycle length (number -1) of sequencer cycles" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " width 19. if (0.<10.) group.long 0x4C8++0x07 line.long 0x00 "DIR_SM0SIGS,Sync mixer 0 signal selection" bitfld.long 0x00 12.--14. " SMX0SIGS_S4 ,SMX0SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX0SIGS_S3 ,SMX0SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX0SIGS_S2 ,SMX0SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX0SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX0SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM0FCTTABLE,The sync mixer output is the result of the function table" else group.long 0x4C8++0x07 line.long 0x00 "DIR_SM0SIGS,Sync mixer 0 signal selection" bitfld.long 0x00 12.--14. " SMX0SIGS_S4 ,SMX0SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX0SIGS_S3 ,SMX0SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX0SIGS_S2 ,SMX0SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX0SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX0SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM0FCTTABLE,The sync mixer output is the result of the function table" endif if (1.<10.) group.long 0x4D0++0x07 line.long 0x00 "DIR_SM1SIGS,Sync mixer 1 signal selection" bitfld.long 0x00 12.--14. " SMX1SIGS_S4 ,SMX1SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX1SIGS_S3 ,SMX1SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX1SIGS_S2 ,SMX1SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX1SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX1SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM1FCTTABLE,The sync mixer output is the result of the function table" else group.long 0x4D0++0x07 line.long 0x00 "DIR_SM1SIGS,Sync mixer 1 signal selection" bitfld.long 0x00 12.--14. " SMX1SIGS_S4 ,SMX1SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX1SIGS_S3 ,SMX1SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX1SIGS_S2 ,SMX1SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX1SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX1SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM1FCTTABLE,The sync mixer output is the result of the function table" endif if (2.<10.) group.long 0x4D8++0x07 line.long 0x00 "DIR_SM2SIGS,Sync mixer 2 signal selection" bitfld.long 0x00 12.--14. " SMX2SIGS_S4 ,SMX2SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX2SIGS_S3 ,SMX2SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX2SIGS_S2 ,SMX2SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX2SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX2SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM2FCTTABLE,The sync mixer output is the result of the function table" else group.long 0x4D8++0x07 line.long 0x00 "DIR_SM2SIGS,Sync mixer 2 signal selection" bitfld.long 0x00 12.--14. " SMX2SIGS_S4 ,SMX2SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX2SIGS_S3 ,SMX2SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX2SIGS_S2 ,SMX2SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX2SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX2SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM2FCTTABLE,The sync mixer output is the result of the function table" endif if (3.<10.) group.long 0x4E0++0x07 line.long 0x00 "DIR_SM3SIGS,Sync mixer 3 signal selection" bitfld.long 0x00 12.--14. " SMX3SIGS_S4 ,SMX3SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX3SIGS_S3 ,SMX3SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX3SIGS_S2 ,SMX3SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX3SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX3SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM3FCTTABLE,The sync mixer output is the result of the function table" else group.long 0x4E0++0x07 line.long 0x00 "DIR_SM3SIGS,Sync mixer 3 signal selection" bitfld.long 0x00 12.--14. " SMX3SIGS_S4 ,SMX3SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX3SIGS_S3 ,SMX3SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX3SIGS_S2 ,SMX3SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX3SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX3SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM3FCTTABLE,The sync mixer output is the result of the function table" endif if (4.<10.) group.long 0x4E8++0x07 line.long 0x00 "DIR_SM4SIGS,Sync mixer 4 signal selection" bitfld.long 0x00 12.--14. " SMX4SIGS_S4 ,SMX4SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX4SIGS_S3 ,SMX4SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX4SIGS_S2 ,SMX4SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX4SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX4SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM4FCTTABLE,The sync mixer output is the result of the function table" else group.long 0x4E8++0x07 line.long 0x00 "DIR_SM4SIGS,Sync mixer 4 signal selection" bitfld.long 0x00 12.--14. " SMX4SIGS_S4 ,SMX4SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX4SIGS_S3 ,SMX4SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX4SIGS_S2 ,SMX4SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX4SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX4SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM4FCTTABLE,The sync mixer output is the result of the function table" endif if (5.<10.) group.long 0x4F0++0x07 line.long 0x00 "DIR_SM5SIGS,Sync mixer 5 signal selection" bitfld.long 0x00 12.--14. " SMX5SIGS_S4 ,SMX5SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX5SIGS_S3 ,SMX5SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX5SIGS_S2 ,SMX5SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX5SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX5SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM5FCTTABLE,The sync mixer output is the result of the function table" else group.long 0x4F0++0x07 line.long 0x00 "DIR_SM5SIGS,Sync mixer 5 signal selection" bitfld.long 0x00 12.--14. " SMX5SIGS_S4 ,SMX5SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX5SIGS_S3 ,SMX5SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX5SIGS_S2 ,SMX5SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX5SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX5SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM5FCTTABLE,The sync mixer output is the result of the function table" endif if (6.<10.) group.long 0x4F8++0x07 line.long 0x00 "DIR_SM6SIGS,Sync mixer 6 signal selection" bitfld.long 0x00 12.--14. " SMX6SIGS_S4 ,SMX6SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX6SIGS_S3 ,SMX6SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX6SIGS_S2 ,SMX6SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX6SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX6SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM6FCTTABLE,The sync mixer output is the result of the function table" else group.long 0x4F8++0x07 line.long 0x00 "DIR_SM6SIGS,Sync mixer 6 signal selection" bitfld.long 0x00 12.--14. " SMX6SIGS_S4 ,SMX6SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX6SIGS_S3 ,SMX6SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX6SIGS_S2 ,SMX6SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX6SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX6SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM6FCTTABLE,The sync mixer output is the result of the function table" endif if (7.<10.) group.long 0x500++0x07 line.long 0x00 "DIR_SM7SIGS,Sync mixer 7 signal selection" bitfld.long 0x00 12.--14. " SMX7SIGS_S4 ,SMX7SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX7SIGS_S3 ,SMX7SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX7SIGS_S2 ,SMX7SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX7SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX7SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM7FCTTABLE,The sync mixer output is the result of the function table" else group.long 0x500++0x07 line.long 0x00 "DIR_SM7SIGS,Sync mixer 7 signal selection" bitfld.long 0x00 12.--14. " SMX7SIGS_S4 ,SMX7SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX7SIGS_S3 ,SMX7SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX7SIGS_S2 ,SMX7SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX7SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX7SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM7FCTTABLE,The sync mixer output is the result of the function table" endif if (8.<10.) group.long 0x508++0x07 line.long 0x00 "DIR_SM8SIGS,Sync mixer 8 signal selection" bitfld.long 0x00 12.--14. " SMX8SIGS_S4 ,SMX8SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX8SIGS_S3 ,SMX8SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX8SIGS_S2 ,SMX8SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX8SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX8SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM8FCTTABLE,The sync mixer output is the result of the function table" else group.long 0x508++0x07 line.long 0x00 "DIR_SM8SIGS,Sync mixer 8 signal selection" bitfld.long 0x00 12.--14. " SMX8SIGS_S4 ,SMX8SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX8SIGS_S3 ,SMX8SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX8SIGS_S2 ,SMX8SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX8SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX8SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM8FCTTABLE,The sync mixer output is the result of the function table" endif if (9.<10.) group.long 0x510++0x07 line.long 0x00 "DIR_SM9SIGS,Sync mixer 9 signal selection" bitfld.long 0x00 12.--14. " SMX9SIGS_S4 ,SMX9SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX9SIGS_S3 ,SMX9SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX9SIGS_S2 ,SMX9SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX9SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX9SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM9FCTTABLE,The sync mixer output is the result of the function table" else group.long 0x510++0x07 line.long 0x00 "DIR_SM9SIGS,Sync mixer 9 signal selection" bitfld.long 0x00 12.--14. " SMX9SIGS_S4 ,SMX9SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX9SIGS_S3 ,SMX9SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX9SIGS_S2 ,SMX9SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX9SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX9SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM9FCTTABLE,The sync mixer output is the result of the function table" endif if (10.<10.) group.long 0x518++0x07 line.long 0x00 "DIR_SM10SIGS,Sync mixer 10 signal selection" bitfld.long 0x00 12.--14. " SMX10SIGS_S4 ,SMX10SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX10SIGS_S3 ,SMX10SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX10SIGS_S2 ,SMX10SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX10SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX10SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM10FCTTABLE,The sync mixer output is the result of the function table" else group.long 0x518++0x07 line.long 0x00 "DIR_SM10SIGS,Sync mixer 10 signal selection" bitfld.long 0x00 12.--14. " SMX10SIGS_S4 ,SMX10SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX10SIGS_S3 ,SMX10SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX10SIGS_S2 ,SMX10SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX10SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX10SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM10FCTTABLE,The sync mixer output is the result of the function table" endif if (11.<10.) group.long 0x520++0x07 line.long 0x00 "DIR_SM11SIGS,Sync mixer 11 signal selection" bitfld.long 0x00 12.--14. " SMX11SIGS_S4 ,SMX11SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX11SIGS_S3 ,SMX11SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX11SIGS_S2 ,SMX11SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX11SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX11SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM11FCTTABLE,The sync mixer output is the result of the function table" else group.long 0x520++0x07 line.long 0x00 "DIR_SM11SIGS,Sync mixer 11 signal selection" bitfld.long 0x00 12.--14. " SMX11SIGS_S4 ,SMX11SIGS_S4" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 9.--11. " SMX11SIGS_S3 ,SMX11SIGS_S3" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 6.--8. " SMX11SIGS_S2 ,SMX11SIGS_S2" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" bitfld.long 0x00 3.--5. " SMX11SIGS_S1 ,SMX0SIGS_S1" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" textline " " bitfld.long 0x00 0.--2. " SMX11SIGS_S0 ,SMX0SIGS_S0" "Const 0,Sequencer,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator,Pulse Generator" line.long 0x04 "DIR_SM11FCTTABLE,The sync mixer output is the result of the function table" endif group.long 0x528++0x07 line.long 0x00 "DIR_SSWITCH,Register for TSIG output configuration" bitfld.long 0x00 28. " ENOPTCLK[28] ,Enable optional (delayed) sample clock for the respective TCON control signal" "Disabled,Enabled" bitfld.long 0x00 27. " ENOPTCLK[27] ,Enable optional (delayed) sample clock for the respective TCON control signal" "Disabled,Enabled" textline " " bitfld.long 0x00 26. " ENOPTCLK[26] ,Enable optional (delayed) sample clock for the respective TCON control signal" "Disabled,Enabled" bitfld.long 0x00 25. " ENOPTCLK[25] ,Enable optional (delayed) sample clock for the respective TCON control signal" "Disabled,Enabled" textline " " bitfld.long 0x00 24. " ENOPTCLK[24] ,Enable optional (delayed) sample clock for the respective TCON control signal" "Disabled,Enabled" bitfld.long 0x00 23. " ENOPTCLK[23] ,Enable optional (delayed) sample clock for the respective TCON control signal" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " ENOPTCLK[22] ,Enable optional (delayed) sample clock for the respective TCON control signal" "Disabled,Enabled" bitfld.long 0x00 21. " ENOPTCLK[21] ,Enable optional (delayed) sample clock for the respective TCON control signal" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " ENOPTCLK[20] ,Enable optional (delayed) sample clock for the respective TCON control signal" "Disabled,Enabled" bitfld.long 0x00 19. " ENOPTCLK[19] ,Enable optional (delayed) sample clock for the respective TCON control signal" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENOPTCLK[18] ,Enable optional (delayed) sample clock for the respective TCON control signal" "Disabled,Enabled" bitfld.long 0x00 17. " ENOPTCLK[17] ,Enable optional (delayed) sample clock for the respective TCON control signal" "Disabled,Enabled" textline " " bitfld.long 0x00 16. " ENOPTCLK[16] ,Enable optional (delayed) sample clock for the respective TCON control signal" "Disabled,Enabled" bitfld.long 0x00 13. " INVCTREN ,Inversion control enable" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " SSWITCH[12] ,Delay selection for the respective TSIG output including inversion control" "None,0.5 cycle delay" bitfld.long 0x00 11. " SSWITCH[11] ,Delay selection for the respective TSIG output including inversion control" "None,0.5 cycle delay" textline " " bitfld.long 0x00 10. " SSWITCH[10] ,Delay selection for the respective TSIG output including inversion control" "None,0.5 cycle delay" bitfld.long 0x00 9. " SSWITCH[9] ,Delay selection for the respective TSIG output including inversion control" "None,0.5 cycle delay" textline " " bitfld.long 0x00 8. " SSWITCH[8] ,Delay selection for the respective TSIG output including inversion control" "None,0.5 cycle delay" bitfld.long 0x00 7. " SSWITCH[7] ,Delay selection for the respective TSIG output including inversion control" "None,0.5 cycle delay" textline " " bitfld.long 0x00 6. " SSWITCH[6] ,Delay selection for the respective TSIG output including inversion control" "None,0.5 cycle delay" bitfld.long 0x00 5. " SSWITCH[5] ,Delay selection for the respective TSIG output including inversion control" "None,0.5 cycle delay" textline " " bitfld.long 0x00 4. " SSWITCH[4] ,Delay selection for the respective TSIG output including inversion control" "None,0.5 cycle delay" bitfld.long 0x00 3. " SSWITCH[3] ,Delay selection for the respective TSIG output including inversion control" "None,0.5 cycle delay" textline " " bitfld.long 0x00 2. " SSWITCH[2] ,Delay selection for the respective TSIG output including inversion control" "None,0.5 cycle delay" bitfld.long 0x00 1. " SSWITCH[1] ,Delay selection for the respective TSIG output including inversion control" "None,0.5 cycle delay" textline " " bitfld.long 0x00 0. " SSWITCH[0] ,Delay selection for the respective TSIG output including inversion control" "None,0.5 cycle delay" line.long 0x04 "DIR_RBM_CTRL,RSDS Bitmap Control" bitfld.long 0x04 8.--10. " COLORDER ,Color Component Ordering" "RGB,BRG,GBR,RBG,GRB,BGR,," bitfld.long 0x04 5. " BITORDER ,Bit order inversion" "Normal order,Inverted order" textline " " bitfld.long 0x04 4. " SWAPODDEVENBIT ,swapoddevenbit" "No swap,Swap" textline " " bitfld.long 0x04 3. " BITPERCOL ,Bit per color" "6Bit,8Bit" bitfld.long 0x04 1.--2. " IFCTYPE ,Interface protocol type" "TTL,RSDS,," textline " " bitfld.long 0x04 0. " BYPASS ,Bypass module" "Disabled,Enabled" width 16. tree "IO Module Pad Control" if (((per.l(ad:0x28000000+0x52C))&0x01)==0x00) if (0.==0.) if (((per.l(ad:0x28000000+0x534))&0x10)==0x10) group.long 0x534++0x03 line.long 0x00 "DIR_PIN0_CTRL,IO Module Pad 0 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 1,Channel 0,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 0,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x534++0x03 line.long 0x00 "DIR_PIN0_CTRL,IO Module Pad 0 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 0,,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (0.==11.) if (((per.l(ad:0x28000000+0x534))&0x10)==0x10) group.long 0x534++0x03 line.long 0x00 "DIR_PIN0_CTRL,IO Module Pad 0 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 0,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x534++0x03 line.long 0x00 "DIR_PIN0_CTRL,IO Module Pad 0 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 18446744073709551615,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay," bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (0.==12.) if (((per.l(ad:0x28000000+0x534))&0x10)==0x10) group.long 0x534++0x03 line.long 0x00 "DIR_PIN0_CTRL,IO Module Pad 0 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 18446744073709551615,INV,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x534++0x03 line.long 0x00 "DIR_PIN0_CTRL,IO Module Pad 0 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 18446744073709551615,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (0.==10.) if (((per.l(ad:0x28000000+0x534))&0x10)==0x10) group.long 0x534++0x03 line.long 0x00 "DIR_PIN0_CTRL,IO Module Pad 0 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 1,Channel 0,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 0,Channel 18446744073709551615,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x534++0x03 line.long 0x00 "DIR_PIN0_CTRL,IO Module Pad 0 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 0,Channel 18446744073709551615,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif else if (((per.l(ad:0x28000000+0x534))&0x10)==0x10) group.long 0x534++0x03 line.long 0x00 "DIR_PIN0_CTRL,IO Module Pad 0 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 1,Channel 0,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 0,Channel 18446744073709551615,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x534++0x03 line.long 0x00 "DIR_PIN0_CTRL,IO Module Pad 0 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 0,Channel 18446744073709551615,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif endif if (1.==0.) if (((per.l(ad:0x28000000+0x538))&0x10)==0x10) group.long 0x538++0x03 line.long 0x00 "DIR_PIN1_CTRL,IO Module Pad 1 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 3,Channel 2,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 2,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x538++0x03 line.long 0x00 "DIR_PIN1_CTRL,IO Module Pad 1 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 1,,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (1.==11.) if (((per.l(ad:0x28000000+0x538))&0x10)==0x10) group.long 0x538++0x03 line.long 0x00 "DIR_PIN1_CTRL,IO Module Pad 1 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 2,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x538++0x03 line.long 0x00 "DIR_PIN1_CTRL,IO Module Pad 1 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 0,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay," bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (1.==12.) if (((per.l(ad:0x28000000+0x538))&0x10)==0x10) group.long 0x538++0x03 line.long 0x00 "DIR_PIN1_CTRL,IO Module Pad 1 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 1,INV,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x538++0x03 line.long 0x00 "DIR_PIN1_CTRL,IO Module Pad 1 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 0,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (1.==10.) if (((per.l(ad:0x28000000+0x538))&0x10)==0x10) group.long 0x538++0x03 line.long 0x00 "DIR_PIN1_CTRL,IO Module Pad 1 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 3,Channel 2,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 2,Channel 1,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x538++0x03 line.long 0x00 "DIR_PIN1_CTRL,IO Module Pad 1 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 1,Channel 0,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif else if (((per.l(ad:0x28000000+0x538))&0x10)==0x10) group.long 0x538++0x03 line.long 0x00 "DIR_PIN1_CTRL,IO Module Pad 1 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 3,Channel 2,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 2,Channel 1,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x538++0x03 line.long 0x00 "DIR_PIN1_CTRL,IO Module Pad 1 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 1,Channel 0,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif endif if (2.==0.) if (((per.l(ad:0x28000000+0x53C))&0x10)==0x10) group.long 0x53C++0x03 line.long 0x00 "DIR_PIN2_CTRL,IO Module Pad 2 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 5,Channel 4,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 4,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x53C++0x03 line.long 0x00 "DIR_PIN2_CTRL,IO Module Pad 2 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 2,,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (2.==11.) if (((per.l(ad:0x28000000+0x53C))&0x10)==0x10) group.long 0x53C++0x03 line.long 0x00 "DIR_PIN2_CTRL,IO Module Pad 2 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 4,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x53C++0x03 line.long 0x00 "DIR_PIN2_CTRL,IO Module Pad 2 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 1,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay," bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (2.==12.) if (((per.l(ad:0x28000000+0x53C))&0x10)==0x10) group.long 0x53C++0x03 line.long 0x00 "DIR_PIN2_CTRL,IO Module Pad 2 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 3,INV,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x53C++0x03 line.long 0x00 "DIR_PIN2_CTRL,IO Module Pad 2 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 1,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (2.==10.) if (((per.l(ad:0x28000000+0x53C))&0x10)==0x10) group.long 0x53C++0x03 line.long 0x00 "DIR_PIN2_CTRL,IO Module Pad 2 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 5,Channel 4,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 4,Channel 3,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x53C++0x03 line.long 0x00 "DIR_PIN2_CTRL,IO Module Pad 2 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 2,Channel 1,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif else if (((per.l(ad:0x28000000+0x53C))&0x10)==0x10) group.long 0x53C++0x03 line.long 0x00 "DIR_PIN2_CTRL,IO Module Pad 2 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 5,Channel 4,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 4,Channel 3,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x53C++0x03 line.long 0x00 "DIR_PIN2_CTRL,IO Module Pad 2 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 2,Channel 1,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif endif if (3.==0.) if (((per.l(ad:0x28000000+0x540))&0x10)==0x10) group.long 0x540++0x03 line.long 0x00 "DIR_PIN3_CTRL,IO Module Pad 3 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 7,Channel 6,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 6,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x540++0x03 line.long 0x00 "DIR_PIN3_CTRL,IO Module Pad 3 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 3,,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (3.==11.) if (((per.l(ad:0x28000000+0x540))&0x10)==0x10) group.long 0x540++0x03 line.long 0x00 "DIR_PIN3_CTRL,IO Module Pad 3 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 6,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x540++0x03 line.long 0x00 "DIR_PIN3_CTRL,IO Module Pad 3 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 2,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay," bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (3.==12.) if (((per.l(ad:0x28000000+0x540))&0x10)==0x10) group.long 0x540++0x03 line.long 0x00 "DIR_PIN3_CTRL,IO Module Pad 3 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 5,INV,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x540++0x03 line.long 0x00 "DIR_PIN3_CTRL,IO Module Pad 3 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 2,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (3.==10.) if (((per.l(ad:0x28000000+0x540))&0x10)==0x10) group.long 0x540++0x03 line.long 0x00 "DIR_PIN3_CTRL,IO Module Pad 3 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 7,Channel 6,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 6,Channel 5,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x540++0x03 line.long 0x00 "DIR_PIN3_CTRL,IO Module Pad 3 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 3,Channel 2,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif else if (((per.l(ad:0x28000000+0x540))&0x10)==0x10) group.long 0x540++0x03 line.long 0x00 "DIR_PIN3_CTRL,IO Module Pad 3 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 7,Channel 6,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 6,Channel 5,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x540++0x03 line.long 0x00 "DIR_PIN3_CTRL,IO Module Pad 3 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 3,Channel 2,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif endif if (4.==0.) if (((per.l(ad:0x28000000+0x544))&0x10)==0x10) group.long 0x544++0x03 line.long 0x00 "DIR_PIN4_CTRL,IO Module Pad 4 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 9,Channel 8,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 8,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x544++0x03 line.long 0x00 "DIR_PIN4_CTRL,IO Module Pad 4 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 4,,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (4.==11.) if (((per.l(ad:0x28000000+0x544))&0x10)==0x10) group.long 0x544++0x03 line.long 0x00 "DIR_PIN4_CTRL,IO Module Pad 4 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 8,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x544++0x03 line.long 0x00 "DIR_PIN4_CTRL,IO Module Pad 4 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 3,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay," bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (4.==12.) if (((per.l(ad:0x28000000+0x544))&0x10)==0x10) group.long 0x544++0x03 line.long 0x00 "DIR_PIN4_CTRL,IO Module Pad 4 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 7,INV,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x544++0x03 line.long 0x00 "DIR_PIN4_CTRL,IO Module Pad 4 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 3,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (4.==10.) if (((per.l(ad:0x28000000+0x544))&0x10)==0x10) group.long 0x544++0x03 line.long 0x00 "DIR_PIN4_CTRL,IO Module Pad 4 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 9,Channel 8,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 8,Channel 7,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x544++0x03 line.long 0x00 "DIR_PIN4_CTRL,IO Module Pad 4 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 4,Channel 3,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif else if (((per.l(ad:0x28000000+0x544))&0x10)==0x10) group.long 0x544++0x03 line.long 0x00 "DIR_PIN4_CTRL,IO Module Pad 4 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 9,Channel 8,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 8,Channel 7,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x544++0x03 line.long 0x00 "DIR_PIN4_CTRL,IO Module Pad 4 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 4,Channel 3,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif endif if (5.==0.) if (((per.l(ad:0x28000000+0x548))&0x10)==0x10) group.long 0x548++0x03 line.long 0x00 "DIR_PIN5_CTRL,IO Module Pad 5 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 11,Channel 10,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 10,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x548++0x03 line.long 0x00 "DIR_PIN5_CTRL,IO Module Pad 5 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 5,,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (5.==11.) if (((per.l(ad:0x28000000+0x548))&0x10)==0x10) group.long 0x548++0x03 line.long 0x00 "DIR_PIN5_CTRL,IO Module Pad 5 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 10,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x548++0x03 line.long 0x00 "DIR_PIN5_CTRL,IO Module Pad 5 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 4,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay," bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (5.==12.) if (((per.l(ad:0x28000000+0x548))&0x10)==0x10) group.long 0x548++0x03 line.long 0x00 "DIR_PIN5_CTRL,IO Module Pad 5 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 9,INV,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x548++0x03 line.long 0x00 "DIR_PIN5_CTRL,IO Module Pad 5 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 4,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (5.==10.) if (((per.l(ad:0x28000000+0x548))&0x10)==0x10) group.long 0x548++0x03 line.long 0x00 "DIR_PIN5_CTRL,IO Module Pad 5 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 11,Channel 10,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 10,Channel 9,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x548++0x03 line.long 0x00 "DIR_PIN5_CTRL,IO Module Pad 5 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 5,Channel 4,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif else if (((per.l(ad:0x28000000+0x548))&0x10)==0x10) group.long 0x548++0x03 line.long 0x00 "DIR_PIN5_CTRL,IO Module Pad 5 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 11,Channel 10,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 10,Channel 9,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x548++0x03 line.long 0x00 "DIR_PIN5_CTRL,IO Module Pad 5 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 5,Channel 4,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif endif if (6.==0.) if (((per.l(ad:0x28000000+0x54C))&0x10)==0x10) group.long 0x54C++0x03 line.long 0x00 "DIR_PIN6_CTRL,IO Module Pad 6 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 13,Channel 12,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 12,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x54C++0x03 line.long 0x00 "DIR_PIN6_CTRL,IO Module Pad 6 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 6,,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (6.==11.) if (((per.l(ad:0x28000000+0x54C))&0x10)==0x10) group.long 0x54C++0x03 line.long 0x00 "DIR_PIN6_CTRL,IO Module Pad 6 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 12,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x54C++0x03 line.long 0x00 "DIR_PIN6_CTRL,IO Module Pad 6 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 5,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay," bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (6.==12.) if (((per.l(ad:0x28000000+0x54C))&0x10)==0x10) group.long 0x54C++0x03 line.long 0x00 "DIR_PIN6_CTRL,IO Module Pad 6 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 11,INV,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x54C++0x03 line.long 0x00 "DIR_PIN6_CTRL,IO Module Pad 6 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 5,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (6.==10.) if (((per.l(ad:0x28000000+0x54C))&0x10)==0x10) group.long 0x54C++0x03 line.long 0x00 "DIR_PIN6_CTRL,IO Module Pad 6 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 13,Channel 12,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 12,Channel 11,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x54C++0x03 line.long 0x00 "DIR_PIN6_CTRL,IO Module Pad 6 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 6,Channel 5,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif else if (((per.l(ad:0x28000000+0x54C))&0x10)==0x10) group.long 0x54C++0x03 line.long 0x00 "DIR_PIN6_CTRL,IO Module Pad 6 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 13,Channel 12,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 12,Channel 11,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x54C++0x03 line.long 0x00 "DIR_PIN6_CTRL,IO Module Pad 6 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 6,Channel 5,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif endif if (7.==0.) if (((per.l(ad:0x28000000+0x550))&0x10)==0x10) group.long 0x550++0x03 line.long 0x00 "DIR_PIN7_CTRL,IO Module Pad 7 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 15,Channel 14,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 14,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x550++0x03 line.long 0x00 "DIR_PIN7_CTRL,IO Module Pad 7 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 7,,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (7.==11.) if (((per.l(ad:0x28000000+0x550))&0x10)==0x10) group.long 0x550++0x03 line.long 0x00 "DIR_PIN7_CTRL,IO Module Pad 7 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 14,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x550++0x03 line.long 0x00 "DIR_PIN7_CTRL,IO Module Pad 7 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 6,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay," bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (7.==12.) if (((per.l(ad:0x28000000+0x550))&0x10)==0x10) group.long 0x550++0x03 line.long 0x00 "DIR_PIN7_CTRL,IO Module Pad 7 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 13,INV,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x550++0x03 line.long 0x00 "DIR_PIN7_CTRL,IO Module Pad 7 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 6,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (7.==10.) if (((per.l(ad:0x28000000+0x550))&0x10)==0x10) group.long 0x550++0x03 line.long 0x00 "DIR_PIN7_CTRL,IO Module Pad 7 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 15,Channel 14,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 14,Channel 13,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x550++0x03 line.long 0x00 "DIR_PIN7_CTRL,IO Module Pad 7 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 7,Channel 6,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif else if (((per.l(ad:0x28000000+0x550))&0x10)==0x10) group.long 0x550++0x03 line.long 0x00 "DIR_PIN7_CTRL,IO Module Pad 7 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 15,Channel 14,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 14,Channel 13,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x550++0x03 line.long 0x00 "DIR_PIN7_CTRL,IO Module Pad 7 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 7,Channel 6,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif endif if (8.==0.) if (((per.l(ad:0x28000000+0x554))&0x10)==0x10) group.long 0x554++0x03 line.long 0x00 "DIR_PIN8_CTRL,IO Module Pad 8 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 17,Channel 16,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 16,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x554++0x03 line.long 0x00 "DIR_PIN8_CTRL,IO Module Pad 8 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 8,,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (8.==11.) if (((per.l(ad:0x28000000+0x554))&0x10)==0x10) group.long 0x554++0x03 line.long 0x00 "DIR_PIN8_CTRL,IO Module Pad 8 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 16,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x554++0x03 line.long 0x00 "DIR_PIN8_CTRL,IO Module Pad 8 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 7,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay," bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (8.==12.) if (((per.l(ad:0x28000000+0x554))&0x10)==0x10) group.long 0x554++0x03 line.long 0x00 "DIR_PIN8_CTRL,IO Module Pad 8 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 15,INV,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x554++0x03 line.long 0x00 "DIR_PIN8_CTRL,IO Module Pad 8 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 7,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (8.==10.) if (((per.l(ad:0x28000000+0x554))&0x10)==0x10) group.long 0x554++0x03 line.long 0x00 "DIR_PIN8_CTRL,IO Module Pad 8 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 17,Channel 16,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 16,Channel 15,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x554++0x03 line.long 0x00 "DIR_PIN8_CTRL,IO Module Pad 8 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 8,Channel 7,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif else if (((per.l(ad:0x28000000+0x554))&0x10)==0x10) group.long 0x554++0x03 line.long 0x00 "DIR_PIN8_CTRL,IO Module Pad 8 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 17,Channel 16,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 16,Channel 15,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x554++0x03 line.long 0x00 "DIR_PIN8_CTRL,IO Module Pad 8 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 8,Channel 7,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif endif if (9.==0.) if (((per.l(ad:0x28000000+0x558))&0x10)==0x10) group.long 0x558++0x03 line.long 0x00 "DIR_PIN9_CTRL,IO Module Pad 9 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 19,Channel 18,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 18,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x558++0x03 line.long 0x00 "DIR_PIN9_CTRL,IO Module Pad 9 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 9,,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (9.==11.) if (((per.l(ad:0x28000000+0x558))&0x10)==0x10) group.long 0x558++0x03 line.long 0x00 "DIR_PIN9_CTRL,IO Module Pad 9 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 18,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x558++0x03 line.long 0x00 "DIR_PIN9_CTRL,IO Module Pad 9 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 8,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay," bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (9.==12.) if (((per.l(ad:0x28000000+0x558))&0x10)==0x10) group.long 0x558++0x03 line.long 0x00 "DIR_PIN9_CTRL,IO Module Pad 9 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 17,INV,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x558++0x03 line.long 0x00 "DIR_PIN9_CTRL,IO Module Pad 9 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 8,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (9.==10.) if (((per.l(ad:0x28000000+0x558))&0x10)==0x10) group.long 0x558++0x03 line.long 0x00 "DIR_PIN9_CTRL,IO Module Pad 9 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 19,Channel 18,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 18,Channel 17,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x558++0x03 line.long 0x00 "DIR_PIN9_CTRL,IO Module Pad 9 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 9,Channel 8,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif else if (((per.l(ad:0x28000000+0x558))&0x10)==0x10) group.long 0x558++0x03 line.long 0x00 "DIR_PIN9_CTRL,IO Module Pad 9 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 19,Channel 18,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 18,Channel 17,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x558++0x03 line.long 0x00 "DIR_PIN9_CTRL,IO Module Pad 9 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 9,Channel 8,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif endif if (10.==0.) if (((per.l(ad:0x28000000+0x55C))&0x10)==0x10) group.long 0x55C++0x03 line.long 0x00 "DIR_PIN10_CTRL,IO Module Pad 10 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 21,Channel 20,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 20,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x55C++0x03 line.long 0x00 "DIR_PIN10_CTRL,IO Module Pad 10 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 10,,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (10.==11.) if (((per.l(ad:0x28000000+0x55C))&0x10)==0x10) group.long 0x55C++0x03 line.long 0x00 "DIR_PIN10_CTRL,IO Module Pad 10 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 20,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x55C++0x03 line.long 0x00 "DIR_PIN10_CTRL,IO Module Pad 10 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 9,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay," bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (10.==12.) if (((per.l(ad:0x28000000+0x55C))&0x10)==0x10) group.long 0x55C++0x03 line.long 0x00 "DIR_PIN10_CTRL,IO Module Pad 10 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 19,INV,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x55C++0x03 line.long 0x00 "DIR_PIN10_CTRL,IO Module Pad 10 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 9,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (10.==10.) if (((per.l(ad:0x28000000+0x55C))&0x10)==0x10) group.long 0x55C++0x03 line.long 0x00 "DIR_PIN10_CTRL,IO Module Pad 10 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 21,Channel 20,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 20,Channel 19,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x55C++0x03 line.long 0x00 "DIR_PIN10_CTRL,IO Module Pad 10 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 10,Channel 9,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif else if (((per.l(ad:0x28000000+0x55C))&0x10)==0x10) group.long 0x55C++0x03 line.long 0x00 "DIR_PIN10_CTRL,IO Module Pad 10 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 21,Channel 20,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 20,Channel 19,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x55C++0x03 line.long 0x00 "DIR_PIN10_CTRL,IO Module Pad 10 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 10,Channel 9,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif endif if (11.==0.) if (((per.l(ad:0x28000000+0x560))&0x10)==0x10) group.long 0x560++0x03 line.long 0x00 "DIR_PIN11_CTRL,IO Module Pad 11 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 23,Channel 22,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 22,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x560++0x03 line.long 0x00 "DIR_PIN11_CTRL,IO Module Pad 11 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 11,,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (11.==11.) if (((per.l(ad:0x28000000+0x560))&0x10)==0x10) group.long 0x560++0x03 line.long 0x00 "DIR_PIN11_CTRL,IO Module Pad 11 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 22,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x560++0x03 line.long 0x00 "DIR_PIN11_CTRL,IO Module Pad 11 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 10,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay," bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (11.==12.) if (((per.l(ad:0x28000000+0x560))&0x10)==0x10) group.long 0x560++0x03 line.long 0x00 "DIR_PIN11_CTRL,IO Module Pad 11 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 21,INV,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x560++0x03 line.long 0x00 "DIR_PIN11_CTRL,IO Module Pad 11 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 10,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (11.==10.) if (((per.l(ad:0x28000000+0x560))&0x10)==0x10) group.long 0x560++0x03 line.long 0x00 "DIR_PIN11_CTRL,IO Module Pad 11 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 23,Channel 22,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 22,Channel 21,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x560++0x03 line.long 0x00 "DIR_PIN11_CTRL,IO Module Pad 11 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 11,Channel 10,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif else if (((per.l(ad:0x28000000+0x560))&0x10)==0x10) group.long 0x560++0x03 line.long 0x00 "DIR_PIN11_CTRL,IO Module Pad 11 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 23,Channel 22,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 22,Channel 21,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x560++0x03 line.long 0x00 "DIR_PIN11_CTRL,IO Module Pad 11 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 11,Channel 10,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif endif if (12.==0.) if (((per.l(ad:0x28000000+0x564))&0x10)==0x10) group.long 0x564++0x03 line.long 0x00 "DIR_PIN12_CTRL,IO Module Pad 12 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 25,Channel 24,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 24,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x564++0x03 line.long 0x00 "DIR_PIN12_CTRL,IO Module Pad 12 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 12,,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (12.==11.) if (((per.l(ad:0x28000000+0x564))&0x10)==0x10) group.long 0x564++0x03 line.long 0x00 "DIR_PIN12_CTRL,IO Module Pad 12 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 24,INV,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x564++0x03 line.long 0x00 "DIR_PIN12_CTRL,IO Module Pad 12 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 11,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay," bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (12.==12.) if (((per.l(ad:0x28000000+0x564))&0x10)==0x10) group.long 0x564++0x03 line.long 0x00 "DIR_PIN12_CTRL,IO Module Pad 12 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Const 0,INV,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 23,INV,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x564++0x03 line.long 0x00 "DIR_PIN12_CTRL,IO Module Pad 12 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Clk,Channel 11,,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif elif (12.==10.) if (((per.l(ad:0x28000000+0x564))&0x10)==0x10) group.long 0x564++0x03 line.long 0x00 "DIR_PIN12_CTRL,IO Module Pad 12 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 25,Channel 24,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 24,Channel 23,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x564++0x03 line.long 0x00 "DIR_PIN12_CTRL,IO Module Pad 12 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 12,Channel 11,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif else if (((per.l(ad:0x28000000+0x564))&0x10)==0x10) group.long 0x564++0x03 line.long 0x00 "DIR_PIN12_CTRL,IO Module Pad 12 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 19.--20. " NCHANSEL ,Channel selection for N-Pin of Pad" "Channel 25,Channel 24,Clk,Const 0" bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 24,Channel 23,Clk,Const 0" textline " " bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "Normal,Inverted" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Normal,Inverted" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "2 mA,4 mA,4 mA,8 mA" else group.long 0x564++0x03 line.long 0x00 "DIR_PIN12_CTRL,IO Module Pad 12 Control" bitfld.long 0x00 22. " NOPTCLKEN ,Use optional (delayed) sample clock for N-pin" "Default,Optional" bitfld.long 0x00 21. " OPTCLKEN ,Use optional (delayed) sample clock for pin" "Default,Optional" textline " " bitfld.long 0x00 17.--18. " CHANSEL0 ,Channel selection for Pad(RSDS-TTL)" "Channel 12,Channel 11,Clk,Const 0" textline " " sif (cpuis("MB86R12")) bitfld.long 0x00 14. " NDELAY ,N-pin Padcell delay" "No delay,Half bit clock cycle delay" bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" else bitfld.long 0x00 13. " DELAY ,Pad delay" "No delay,half bit clock cycle delay" endif textline " " bitfld.long 0x00 7. " INOUT ,Output enable control" "Disabled,Enabled" bitfld.long 0x00 6. " NPOLARITY ,N-pin of Padcell drive polarity" "No effect,No effect" textline " " bitfld.long 0x00 5. " POLARITY ,Pad drive polarity" "Inverted,Normal" bitfld.long 0x00 4. " MODE ,Pad drive mode" "Differential,TTL" textline " " bitfld.long 0x00 0.--1. " BOOST ,Output drive strength selection" "100 Ohm,50 Ohm,100 Ohm,50 Ohm" endif endif endif tree.end width 0x0B tree.end tree "RLD (Run-Length Decompression)" base ad:0x04C00000 width 15. group.long 0x00++0x2B line.long 0x00 "SWRESET,SW reset" bitfld.long 0x00 0. " SWRESET ,SW reset" "No reset,Reset" line.long 0x04 "RLDCFG,General configuration register" bitfld.long 0x04 20. " ENDIAN ,The byte order of input data" "Big endian,Little endian" bitfld.long 0x04 16. " CMD_FORMAT ,The format of command byte" "Byte + 1,Byte" textline " " bitfld.long 0x04 8. " ALIGNMODE ,Output data format" "Bit,Word" bitfld.long 0x04 0.--2. " BPP ,Bit per pixel" "1,2,4,8,16,24,32," line.long 0x08 "STRIDECFG0,Stride general configuration register" bitfld.long 0x08 0. " STRIDEEN ,Enable for output data stride alligned" "Disabled,Enabled" line.long 0x0C "STRIDECFG1,Line / Stride Length" hexmask.long.word 0x0C 16.--31. 1. " STRIDE ,Stride: number of byte -1" hexmask.long.word 0x0C 0.--13. 1. " LINELENGTH ,Number of bytes per line - 1" line.long 0x10 "BYTECNT,Target number of decompressed bytes" line.long 0x14 "OFIFO,Output FIFO Control" bitfld.long 0x14 0.--3. " WRITETHRESHOLD ,Number of words-1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x18 "DESTADDRESS,Local AHB-master transfer Destination address" hexmask.long 0x18 2.--31. 0x04 " AHBMDA ,Destination address to start AHB-master transfer" line.long 0x1C "AHBMCTRL,Local AHB-master transfer Configuration/Control" bitfld.long 0x1C 8.--9. " AHBMTRANSFERWIDTH ,AHBMTransferWidth" "Byte,Halfword,Word," bitfld.long 0x1C 0. " AHBMFIXEDDEST ,AHBMFixedDest" "Incremented,Fixed" line.long 0x20 "RLDCTRL,General Control" bitfld.long 0x20 0. " ACCEPTDATA ,Enable Acceptance of compressed Data" "Disabled,Enabled" line.long 0x24 "IEN,Interrupt Enable register" bitfld.long 0x24 3. " IENIFFULL ,Interrupt enable" "No interrupt,Interrupt" bitfld.long 0x24 2. " IENIFEMPTY ,Interrupt enable" "No interrupt,Interrupt" bitfld.long 0x24 1. " IENERROR ,Interrupt enable" "No interrupt,Interrupt" textline " " bitfld.long 0x24 0. " IENCOMPLETE ,Interrupt enable" "No interrupt,Interrupt" line.long 0x28 "ISTS,Interrupt status flags" eventfld.long 0x28 3. " ISTSIFFULL ,Interrupt Status for condition Input FIFO full" "Not Occurred,Occurred" eventfld.long 0x28 2. " ISTSIFEMPTY ,Interrupt Status for condition Input FIFO empty" "Not Occurred,Occurred" eventfld.long 0x28 1. " ISTSERROR ,Interrupt Status for condition AHB Destination access error" "Not Occurred,Occurred" textline " " eventfld.long 0x28 0. " ISTSCOMPLETE ,Interrupt Status for Condition RLD complete" "Not Occurred,Occurred" rgroup.long 0x2C++0x03 line.long 0x00 "STATUS,Status register" bitfld.long 0x00 3. " IFIFOEMPTY ,Input FIFO currently empty" "Not empty,Empty" bitfld.long 0x00 2. " OFIFOFULL ,Output FIFO currently full" "Not full,Full" bitfld.long 0x00 1. " IFIFOFULL ,Input FIFO currently full" "Not full,Full" textline " " bitfld.long 0x00 0. " BUSY ,RLD busy" "Not busy,Busy" group.long 0x30++0x03 line.long 0x00 "SAHBDATA,AHB Slave Input Data" rgroup.long 0x34++0x07 line.long 0x00 "TRANSFERCOUNT,Local AHB-master transfer count" line.long 0x04 "CURADDRESS,Local AHB-master transfer Current address" width 0xb tree.end tree "HS-SPI (High Speed serial peripheral interface)" base ad:0x38100000 width 16. group.long 0x00++0x03 line.long 0x00 "MCTRL,HSSPI Control Register" bitfld.long 0x00 4. " MES ,Module enable status" "Disabled,Enabled" sif (cpu()=="MB86R24") bitfld.long 0x00 3. " CDSS ,Clock division source select" "/iHCLK,/iPCLK" bitfld.long 0x00 2. " DBGEN ,Debug enable" "Disabled,Enabled" endif textline " " bitfld.long 0x00 1. " CSEN ,Command sequencer enable (Direct mode/Command sequencer)" "Direct mode,Command sequencer" bitfld.long 0x00 0. " MEN ,Module enable" "Disabled,Enabled" sif (cpu()=="MB86R24") if (((per.b(ad:0x38100000+0x34))&0x1)==0x01) group.long 0x04++0x0F "Peripheral Communication Configuration Registers" line.long 0x0 "PCC0,HSSPI Peripheral Communication Configuration Register 0" bitfld.long 0x0 16. " SAFESYNC ,Safe synchronisation for peripheral 0" "Disabled,Enabled" hexmask.long.byte 0x0 9.--15. 1. " CDRS ,Clock division ratio select of peripheral 0" bitfld.long 0x0 7. " SDIR ,Shift direction of peripheral 0" "MSB,LSB" textline " " bitfld.long 0x0 5.--6. " SS2CD ,Slave-Select to clock delay of peripheral 0" "0,1,2,3" bitfld.long 0x0 4. " SSPOL ,Slave select polarity of peripheral 0 (signal is active)" "Low,High" bitfld.long 0x0 3. " RTM ,Use retimed clock for capturing the data from peripheral 0" "Not used,Used" textline " " bitfld.long 0x0 2. " ACES ,Active clock edges are same on peripheral 0" "Alternate,Same" bitfld.long 0x0 1. " CPOL ,Clock polarity of peripheral 0" "Low,High" bitfld.long 0x0 0. " CPHA ,Clock phase of peripheral 0" "Odd,Even" line.long 0x4 "PCC1,HSSPI Peripheral Communication Configuration Register 1" bitfld.long 0x4 16. " SAFESYNC ,Safe synchronisation for peripheral 1" "Disabled,Enabled" hexmask.long.byte 0x4 9.--15. 1. " CDRS ,Clock division ratio select of peripheral 1" bitfld.long 0x4 7. " SDIR ,Shift direction of peripheral 1" "MSB,LSB" textline " " bitfld.long 0x4 5.--6. " SS2CD ,Slave-Select to clock delay of peripheral 1" "0,1,2,3" bitfld.long 0x4 4. " SSPOL ,Slave select polarity of peripheral 1 (signal is active)" "Low,High" bitfld.long 0x4 3. " RTM ,Use retimed clock for capturing the data from peripheral 1" "Not used,Used" textline " " bitfld.long 0x4 2. " ACES ,Active clock edges are same on peripheral 1" "Alternate,Same" bitfld.long 0x4 1. " CPOL ,Clock polarity of peripheral 1" "Low,High" bitfld.long 0x4 0. " CPHA ,Clock phase of peripheral 1" "Odd,Even" line.long 0x8 "PCC2,HSSPI Peripheral Communication Configuration Register 2" bitfld.long 0x8 16. " SAFESYNC ,Safe synchronisation for peripheral 2" "Disabled,Enabled" hexmask.long.byte 0x8 9.--15. 1. " CDRS ,Clock division ratio select of peripheral 2" bitfld.long 0x8 7. " SDIR ,Shift direction of peripheral 2" "MSB,LSB" textline " " bitfld.long 0x8 5.--6. " SS2CD ,Slave-Select to clock delay of peripheral 2" "0,1,2,3" bitfld.long 0x8 4. " SSPOL ,Slave select polarity of peripheral 2 (signal is active)" "Low,High" bitfld.long 0x8 3. " RTM ,Use retimed clock for capturing the data from peripheral 2" "Not used,Used" textline " " bitfld.long 0x8 2. " ACES ,Active clock edges are same on peripheral 2" "Alternate,Same" bitfld.long 0x8 1. " CPOL ,Clock polarity of peripheral 2" "Low,High" bitfld.long 0x8 0. " CPHA ,Clock phase of peripheral 2" "Odd,Even" line.long 0xC "PCC3,HSSPI Peripheral Communication Configuration Register 3" bitfld.long 0xC 16. " SAFESYNC ,Safe synchronisation for peripheral 3" "Disabled,Enabled" hexmask.long.byte 0xC 9.--15. 1. " CDRS ,Clock division ratio select of peripheral 3" bitfld.long 0xC 7. " SDIR ,Shift direction of peripheral 3" "MSB,LSB" textline " " bitfld.long 0xC 5.--6. " SS2CD ,Slave-Select to clock delay of peripheral 3" "0,1,2,3" bitfld.long 0xC 4. " SSPOL ,Slave select polarity of peripheral 3 (signal is active)" "Low,High" bitfld.long 0xC 3. " RTM ,Use retimed clock for capturing the data from peripheral 3" "Not used,Used" textline " " bitfld.long 0xC 2. " ACES ,Active clock edges are same on peripheral 3" "Alternate,Same" bitfld.long 0xC 1. " CPOL ,Clock polarity of peripheral 3" "Low,High" bitfld.long 0xC 0. " CPHA ,Clock phase of peripheral 3" "Odd,Even" else group.long 0x04++0x0F "Peripheral Communication Configuration Registers" line.long 0x0 "PCC0,HSSPI Peripheral Communication Configuration Register 0" textline " " bitfld.long 0x0 5.--6. " SS2CD ,Slave-Select to clock delay of peripheral 0" "0,1,2,3" bitfld.long 0x0 4. " SSPOL ,Slave select polarity of peripheral 0 (signal is active)" "Low,High" bitfld.long 0x0 3. " RTM ,Use retimed clock for capturing the data from peripheral 0" "Not used,Used" textline " " bitfld.long 0x0 2. " ACES ,Active clock edges are same on peripheral 0" "Alternate,Same" bitfld.long 0x0 1. " CPOL ,Clock polarity of peripheral 0" "Low,High" bitfld.long 0x0 0. " CPHA ,Clock phase of peripheral 0" "Odd,Even" line.long 0x4 "PCC1,HSSPI Peripheral Communication Configuration Register 1" textline " " bitfld.long 0x4 5.--6. " SS2CD ,Slave-Select to clock delay of peripheral 1" "0,1,2,3" bitfld.long 0x4 4. " SSPOL ,Slave select polarity of peripheral 1 (signal is active)" "Low,High" bitfld.long 0x4 3. " RTM ,Use retimed clock for capturing the data from peripheral 1" "Not used,Used" textline " " bitfld.long 0x4 2. " ACES ,Active clock edges are same on peripheral 1" "Alternate,Same" bitfld.long 0x4 1. " CPOL ,Clock polarity of peripheral 1" "Low,High" bitfld.long 0x4 0. " CPHA ,Clock phase of peripheral 1" "Odd,Even" line.long 0x8 "PCC2,HSSPI Peripheral Communication Configuration Register 2" textline " " bitfld.long 0x8 5.--6. " SS2CD ,Slave-Select to clock delay of peripheral 2" "0,1,2,3" bitfld.long 0x8 4. " SSPOL ,Slave select polarity of peripheral 2 (signal is active)" "Low,High" bitfld.long 0x8 3. " RTM ,Use retimed clock for capturing the data from peripheral 2" "Not used,Used" textline " " bitfld.long 0x8 2. " ACES ,Active clock edges are same on peripheral 2" "Alternate,Same" bitfld.long 0x8 1. " CPOL ,Clock polarity of peripheral 2" "Low,High" bitfld.long 0x8 0. " CPHA ,Clock phase of peripheral 2" "Odd,Even" line.long 0xC "PCC3,HSSPI Peripheral Communication Configuration Register 3" textline " " bitfld.long 0xC 5.--6. " SS2CD ,Slave-Select to clock delay of peripheral 3" "0,1,2,3" bitfld.long 0xC 4. " SSPOL ,Slave select polarity of peripheral 3 (signal is active)" "Low,High" bitfld.long 0xC 3. " RTM ,Use retimed clock for capturing the data from peripheral 3" "Not used,Used" textline " " bitfld.long 0xC 2. " ACES ,Active clock edges are same on peripheral 3" "Alternate,Same" bitfld.long 0xC 1. " CPOL ,Clock polarity of peripheral 3" "Low,High" bitfld.long 0xC 0. " CPHA ,Clock phase of peripheral 3" "Odd,Even" endif else group.long 0x04++0x0F "Peripheral Communication Configuration Registers" line.long 0x0 "PCC0,HSSPI Peripheral Communication Configuration Register 0" bitfld.long 0x0 16. " SAFESYNC ,Safe synchronisation for peripheral 0" "Disabled,Enabled" hexmask.long.byte 0x0 9.--15. 1. " CDRS ,Clock division ratio select of peripheral 0" bitfld.long 0x0 7. " SDIR ,Shift direction of peripheral 0" "MSB,LSB" textline " " bitfld.long 0x0 5.--6. " SS2CD ,Slave-Select to clock delay of peripheral 0" "0,1,2,3" bitfld.long 0x0 4. " SSPOL ,Slave select polarity of peripheral 0 (signal is active)" "Low,High" bitfld.long 0x0 3. " RTM ,Use retimed clock for capturing the data from peripheral 0" "Not used,Used" textline " " bitfld.long 0x0 2. " ACES ,Active clock edges are same on peripheral 0" "Alternate,Same" bitfld.long 0x0 1. " CPOL ,Clock polarity of peripheral 0" "Low,High" bitfld.long 0x0 0. " CPHA ,Clock phase of peripheral 0" "Odd,Even" line.long 0x4 "PCC1,HSSPI Peripheral Communication Configuration Register 1" bitfld.long 0x4 16. " SAFESYNC ,Safe synchronisation for peripheral 1" "Disabled,Enabled" hexmask.long.byte 0x4 9.--15. 1. " CDRS ,Clock division ratio select of peripheral 1" bitfld.long 0x4 7. " SDIR ,Shift direction of peripheral 1" "MSB,LSB" textline " " bitfld.long 0x4 5.--6. " SS2CD ,Slave-Select to clock delay of peripheral 1" "0,1,2,3" bitfld.long 0x4 4. " SSPOL ,Slave select polarity of peripheral 1 (signal is active)" "Low,High" bitfld.long 0x4 3. " RTM ,Use retimed clock for capturing the data from peripheral 1" "Not used,Used" textline " " bitfld.long 0x4 2. " ACES ,Active clock edges are same on peripheral 1" "Alternate,Same" bitfld.long 0x4 1. " CPOL ,Clock polarity of peripheral 1" "Low,High" bitfld.long 0x4 0. " CPHA ,Clock phase of peripheral 1" "Odd,Even" line.long 0x8 "PCC2,HSSPI Peripheral Communication Configuration Register 2" bitfld.long 0x8 16. " SAFESYNC ,Safe synchronisation for peripheral 2" "Disabled,Enabled" hexmask.long.byte 0x8 9.--15. 1. " CDRS ,Clock division ratio select of peripheral 2" bitfld.long 0x8 7. " SDIR ,Shift direction of peripheral 2" "MSB,LSB" textline " " bitfld.long 0x8 5.--6. " SS2CD ,Slave-Select to clock delay of peripheral 2" "0,1,2,3" bitfld.long 0x8 4. " SSPOL ,Slave select polarity of peripheral 2 (signal is active)" "Low,High" bitfld.long 0x8 3. " RTM ,Use retimed clock for capturing the data from peripheral 2" "Not used,Used" textline " " bitfld.long 0x8 2. " ACES ,Active clock edges are same on peripheral 2" "Alternate,Same" bitfld.long 0x8 1. " CPOL ,Clock polarity of peripheral 2" "Low,High" bitfld.long 0x8 0. " CPHA ,Clock phase of peripheral 2" "Odd,Even" line.long 0xC "PCC3,HSSPI Peripheral Communication Configuration Register 3" bitfld.long 0xC 16. " SAFESYNC ,Safe synchronisation for peripheral 3" "Disabled,Enabled" hexmask.long.byte 0xC 9.--15. 1. " CDRS ,Clock division ratio select of peripheral 3" bitfld.long 0xC 7. " SDIR ,Shift direction of peripheral 3" "MSB,LSB" textline " " bitfld.long 0xC 5.--6. " SS2CD ,Slave-Select to clock delay of peripheral 3" "0,1,2,3" bitfld.long 0xC 4. " SSPOL ,Slave select polarity of peripheral 3 (signal is active)" "Low,High" bitfld.long 0xC 3. " RTM ,Use retimed clock for capturing the data from peripheral 3" "Not used,Used" textline " " bitfld.long 0xC 2. " ACES ,Active clock edges are same on peripheral 3" "Alternate,Same" bitfld.long 0xC 1. " CPOL ,Clock polarity of peripheral 3" "Low,High" bitfld.long 0xC 0. " CPHA ,Clock phase of peripheral 3" "Odd,Even" endif rgroup.long 0x14++0x03 "Interrupt Registers" line.long 0x00 "TXF,HSSPI TX Interrupt Flag Register" bitfld.long 0x00 6. " TSSRS ,Slave select released" "No interrupt,Interrupt" bitfld.long 0x00 5. " TFMTS ,TX-FIFO fill level is more than threshold" "No interrupt,Interrupt" bitfld.long 0x00 4. " TFLETS ,TX-FIFO fill level is less than or equal to threshold" "No interrupt,Interrupt" textline " " bitfld.long 0x00 3. " TFUS ,TX-FIFO underrun" "No interrupt,Interrupt" bitfld.long 0x00 2. " TFOS ,TX-FIFO overrun" "No interrupt,Interrupt" bitfld.long 0x00 1. " TFES ,TX-FIFO and shift register is empty" "No interrupt,Interrupt" textline " " bitfld.long 0x00 0. " TFFS ,TX-FIFO full" "No interrupt,Interrupt" group.long 0x18++0x03 line.long 0x00 "TXE,HSSPI TX Interrupt Enable Register" bitfld.long 0x00 6. " TSSRE ,Slave select released interrupt enable" "Disabled,Enabled" bitfld.long 0x00 5. " TFMTE ,TX-FIFO fill level is more than threshold interrupt enable" "Disabled,Enabled" bitfld.long 0x00 4. " TFLETE ,TX-FIFO fill level is less than or equal to threshold interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " TFUE ,TX-FIFO underrun interrupt enable" "Disabled,Enabled" bitfld.long 0x00 2. " TFOE ,TX-FIFO overrun interrupt enable" "Disabled,Enabled" bitfld.long 0x00 1. " TFEE ,TX-FIFO empty interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " TFFE ,TX-FIFO full interrupt enable" "Disabled,Enabled" wgroup.long 0x1C++0x03 line.long 0x00 "TXC,HSSPI TX Interrupt Clear Register" bitfld.long 0x00 6. " TSSRC ,Slave select released interrupt (TXF:TSSRS) clear" "No effect,Clear" bitfld.long 0x00 5. " TFMTC ,TX-FIFO fill level is more than threshold interrupt (TXF:TFMTS) clear" "No effect,Clear" bitfld.long 0x00 4. " TFLETC ,TX-FIFO fill level is less than or equal to threshold interrupt (TXF:TFLETS) clear" "No effect,Clear" textline " " bitfld.long 0x00 3. " TFUC ,TX-FIFO underrun interrupt (TXF:TFUS) clear" "No effect,Clear" bitfld.long 0x00 2. " TFOC ,TX-FIFO overrun interrupt (TXF:TFOS) clear" "No effect,Clear" bitfld.long 0x00 1. " TFEC ,TX-FIFO empty interrupt (TXF:TFES) clear" "No effect,Clear" textline " " bitfld.long 0x00 0. " TFFC ,TX-FIFO full interrupt (TXF:TFFS) clear" "No effect,Clear" rgroup.long 0x20++0x03 line.long 0x00 "RXF,HSSPI RX Interrupt Flag Register" bitfld.long 0x00 6. " RSSRS ,Slave select released" "No interrupt,Interrupt" bitfld.long 0x00 5. " RFMTS ,RX-FIFO fill level is more than threshold" "No interrupt,Interrupt" bitfld.long 0x00 4. " RFLETS ,RX-FIFO fill level is less than or equal to threshold" "No interrupt,Interrupt" textline " " bitfld.long 0x00 3. " RFUS ,TX-RIFO underrun" "No interrupt,Interrupt" bitfld.long 0x00 2. " RFOS ,RX-FIFO overrun" "No interrupt,Interrupt" bitfld.long 0x00 1. " RFES ,RX-FIFO empty" "No interrupt,Interrupt" textline " " bitfld.long 0x00 0. " RFFS ,RX-FIFO full" "No interrupt,Interrupt" group.long 0x24++0x03 line.long 0x00 "RXE,HSSPI RX Interrupt Enable Register" bitfld.long 0x00 6. " RSSRE ,Slave select released interrupt enable" "Disabled,Enabled" bitfld.long 0x00 5. " RFMTE ,RX-FIFO fill level is more than threshold interrupt enable" "Disabled,Enabled" bitfld.long 0x00 4. " RFLETE ,RX-FIFO fill level is less than or equal to threshold interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " RFUE ,RX-FIFO underrun interrupt enable" "Disabled,Enabled" bitfld.long 0x00 2. " RFOE ,RX-FIFO overrun interrupt enable" "Disabled,Enabled" bitfld.long 0x00 1. " RFEE ,RX-FIFO empty interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " RFFE ,RX-FIFO full interrupt enable" "Disabled,Enabled" wgroup.long 0x28++0x03 line.long 0x00 "RXC,HSSPI RX Interrupt Clear Register" bitfld.long 0x00 6. " RSSRC ,Slave select released interrupt (RXF:RSSRS) clear" "No effect,Clear" bitfld.long 0x00 5. " RFMTC ,RX-FIFO fill level is more than threshold interrupt (RXF:RFMTS) clear" "No effect,Clear" bitfld.long 0x00 4. " RFLETC ,RX-FIFO fill level is less than or equal to threshold interrupt (RXF:RFLETS) clear" "No effect,Clear" textline " " bitfld.long 0x00 3. " RFUC ,RX-FIFO underrun interrupt (RXF:RFUS) clear" "No effect,Clear" bitfld.long 0x00 2. " RFOC ,RX-FIFO overrun interrupt (RXF:RFOS) clear" "No effect,Clear" bitfld.long 0x00 1. " RFEC ,RX-FIFO empty interrupt (RXF:RFES) clear" "No effect,Clear" textline " " bitfld.long 0x00 0. " RFFC ,RX-FIFO full interrupt (RXF:RFFS) clear" "No effect,Clear" rgroup.long 0x2C++0x03 line.long 0x00 "FAULTF,HSSPI Fault Interrupt Flag Register" bitfld.long 0x00 4. " DRCBSFS ,DMA read channel block size fault" "No interrupt,Interrupt" bitfld.long 0x00 3. " DWCBSFS ,DMA write channel block size fault" "No interrupt,Interrupt" bitfld.long 0x00 2. " PVFS ,Protection violation fault" "No interrupt,Interrupt" textline " " bitfld.long 0x00 1. " WAFS ,Write access fault" "No interrupt,Interrupt" bitfld.long 0x00 0. " UMAFS ,Unmapped memory access fault" "No interrupt,Interrupt" wgroup.long 0x30++0x03 line.long 0x00 "FAULTC,HSSPI Fault Interrupt Clear Register" bitfld.long 0x00 4. " DRCBSFC ,DMA read channel block size fault interrupt (HSSPIn_FAULTF:DRCBSFS) clear" "No effect,Clear" bitfld.long 0x00 3. " DWCBSFC ,DMA write channel block size fault interrupt (HSSPIn_FAULTF:DWCBSFS) clear" "No effect,Clear" bitfld.long 0x00 2. " PVFC ,Protection violation fault interrupt (HSSPIn_FAULTF:PVFS) clear" "No effect,Clear" textline " " bitfld.long 0x00 1. " WAFC ,Write access fault interrupt (HSSPIn_FAULTF:WAFS) clear" "No effect,Clear" bitfld.long 0x00 0. " UMAFC ,Unmapped memory access fault interrupt (HSSPIn_FAULTF:UMAFS) clear" "No effect,Clear" sif (cpu()=="MB86R24") if ((((per.b(ad:0x38100000))&0x2)==0x00)&&(((per.b(ad:0x38100000+0x34))&0x1)==0x01)) group.byte 0x34++0x00 "Direct Mode Registers" line.byte 0x00 "DMCFG,HSSPI Direct Mode Configuration Register" bitfld.byte 0x00 2. " MSTARTEN ,iMSTART enable" "Disabled,Enabled" bitfld.byte 0x00 1. " SSDC ,Slave select deassertion control" "Software flow control,Byte counter mode" textline " " bitfld.byte 0x00 0. " MST ,Master mode" "Slave,Master" elif ((((per.b(ad:0x38100000))&0x02)==0x02)&&(((per.b(ad:0x38100000+0x34))&0x1)==0x01)) group.byte 0x34++0x00 "Direct Mode Registers" line.byte 0x00 "DMCFG,HSSPI Direct Mode Configuration Register" bitfld.byte 0x00 1. " SSDC ,Slave select deassertion control" "Software flow control,Byte counter mode" bitfld.byte 0x00 0. " MST ,Master mode" "Slave,Master" else group.byte 0x34++0x00 "Direct Mode Registers" line.byte 0x00 "DMCFG,HSSPI Direct Mode Configuration Register" bitfld.byte 0x00 0. " MST ,Master mode" "Slave,Master" endif group.byte 0x35++0x00 line.byte 0x00 "DMDMAEN,HSSPI Direct Mode DMA Enable Register" bitfld.byte 0x00 1. " TXDMAEN ,TX DMA enable" "Disabled,Enabled" bitfld.byte 0x00 0. " RXDMAEN ,RX DMA enable" "Disabled,Enabled" if (((per.b(ad:0x38100000+0x34))&0x1)==0x01) wgroup.byte 0x38++0x00 line.byte 0x00 "DMSTART,HSSPI Direct Mode Start Register" bitfld.byte 0x00 0. " START ,Start transfer" "No effect,Start" else hgroup.byte 0x38++0x00 hide.byte 0x00 "DMSTART,HSSPI Direct Mode Start Register" endif if ((((per.b(ad:0x38100000+0x34))&0x2)==0x00)&&(((per.b(ad:0x38100000+0x34))&0x1)==0x01)) group.byte 0x39++0x00 line.byte 0x00 "DMSTOP,HSSPI Direct Mode Stop Register" bitfld.byte 0x00 0. " STOP ,Stop bit" "Asserted,De-asserted" else hgroup.byte 0x39++0x00 hide.byte 0x00 "DMSTOP,HSSPI Direct Mode Stop Register" endif if (((per.b(ad:0x38100000+0x34))&0x1)==0x01) group.byte 0x3A++0x01 line.byte 0x00 "DMPSEL,HSSPI Direct Mode Peripheral Slave Select Register" bitfld.byte 0x00 0.--1. " PSEL ,Peripheral select" "Slave 0,Slave 1,Slave 2,Slave 3" else hgroup.byte 0x3A++0x01 hide.byte 0x00 "DMPSEL,HSSPI Direct Mode Peripheral Slave Select Register" endif group.byte 0x3B++0x00 line.byte 0x00 "DMTRP,HSSPI Direct Mode Transfer Protocol Register" bitfld.byte 0x00 0.--3. " TRP ,Transfer protocol" "Tx/Rx-legacy mode,,,,Rx-legacy mode,Rx-dual mode,Rx-quad mode,,Tx-legacy mode,Tx-dual mode,Tx-quad mode,?..." if ((((per.b(ad:0x38100000+0x34))&0x2)==0x2)&&(((per.b(ad:0x38100000+0x34))&0x1)==0x01)) group.word 0x3C++0x01 line.word 0x00 "DMBCC,HSSPI Direct Mode Byte Count Control Register" rgroup.word 0x3E++0x01 line.word 0x00 "DMBCS,HSSPI Direct Mode Byte Count Status Register" else hgroup.word 0x3C++0x03 hide.word 0x00 "DMBCC,HSSPI Direct Mode Byte Count Control Register" hide.word 0x02 "DMBCS,HSSPI Direct Mode Byte Count Status Register" endif rgroup.long 0x40++0x07 line.long 0x00 "DMSTATUS,HSSPI Direct Mode Status Register" bitfld.long 0x00 16.--20. " TXFLEVEL ,Current fill level of TX-FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 8.--12. " RXFLEVEL ,Current fill level of RX-FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 1. " TXACTIVE ,Transmission active" "Not active,Active" textline " " bitfld.long 0x00 0. " RXACTIVE ,Reception active" "Not active,Active" line.byte 0x04 "TXBITCNT,HSSPI Transmit Bit Count Register" bitfld.byte 0x04 0.--5. " TXBITCNT ,Number of pending transmission bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,?..." else group.byte 0x34++0x00 "Direct Mode Registers" line.byte 0x00 "DMCFG,HSSPI Direct Mode Configuration Register" bitfld.byte 0x00 1. " SSDC ,Slave select deassertion control" "Software flow control,Byte counter mode" if (((per.b(ad:0x38100000))&0x2)==0x00) group.byte 0x35++0x00 line.byte 0x00 "DMDMAEN,HSSPI Direct Mode DMA Enable Register" bitfld.byte 0x00 1. " TXDMAEN ,TX DMA enable" "Disabled,Enabled" bitfld.byte 0x00 0. " RXDMAEN ,RX DMA enable" "Disabled,Enabled" group.byte 0x38++0x00 line.byte 0x00 "DMSTART,HSSPI Direct Mode Start Register" bitfld.byte 0x00 0. " START ,Start transfer" "No effect,Start" else hgroup.byte 0x35++0x00 hide.byte 0x00 "DMDMAEN,HSSPI Direct Mode DMA Enable Register" hgroup.byte 0x38++0x00 hide.byte 0x00 "DMSTART,HSSPI Direct Mode Start Register" endif if ((((per.b(ad:0x38100000+0x34))&0x2)==0x0)&&(((per.b(ad:0x38100000))&0x2)==0x00)) group.byte 0x39++0x00 line.byte 0x00 "DMSTOP,HSSPI Direct Mode Stop Register" bitfld.byte 0x00 0. " STOP ,Stop bit" "Asserted,De-asserted" else hgroup.byte 0x39++0x00 hide.byte 0x00 "DMSTOP,HSSPI Direct Mode Stop Register" endif if (((per.b(ad:0x38100000))&0x2)==0x0) group.byte 0x3A++0x01 line.byte 0x00 "DMPSEL,HSSPI Direct Mode Peripheral Slave Select Register" bitfld.byte 0x00 0.--1. " PSEL ,Peripheral select" "Slave 0,Slave 1,Slave 2,Slave 3" line.byte 0x01 "DMTRP,HSSPI Direct Mode Transfer Protocol Register" bitfld.byte 0x01 0.--3. " TRP ,Transfer protocol" "Tx/Rx-legace mode,,,,Rx-legacy mode,Rx-dual mode,Rx-quad mode,,Tx-legacy mode,Tx-dual mode,Tx-quad mode,?..." else hgroup.byte 0x3A++0x01 hide.byte 0x00 "DMPSEL,HSSPI Direct Mode Peripheral Slave Select Register" hide.byte 0x01 "DMTRP,HSSPI Direct Mode Transfer Protocol Register" endif if ((((per.b(ad:0x38100000+0x34))&0x2)==0x2)&&(((per.b(ad:0x38100000))&0x2)==0x00)) group.word 0x3C++0x01 line.word 0x00 "DMBCC,HSSPI Direct Mode Byte Count Control Register" rgroup.word 0x3E++0x01 line.word 0x00 "DMBCS,HSSPI Direct Mode Byte Count Status Register" else hgroup.word 0x3C++0x03 hide.word 0x00 "DMBCC,HSSPI Direct Mode Byte Count Control Register" hide.word 0x02 "DMBCS,HSSPI Direct Mode Byte Count Status Register" endif if (((per.b(ad:0x38100000))&0x2)==0x0) rgroup.long 0x40++0x03 line.long 0x00 "DMSTATUS,HSSPI Direct Mode Status Register" bitfld.long 0x00 16.--20. " TXFLEVEL ,Current fill level of TX-FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 8.--12. " RXFLEVEL ,Current fill level of RX-FIFO" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 1. " TXACTIVE ,Transmission active" "Not active,Active" textline " " bitfld.long 0x00 0. " RXACTIVE ,Reception active" "Not active,Active" else hgroup.long 0x40++0x03 hide.long 0x00 "DMSTATUS,HSSPI Direct Mode Status Register" endif if (((per.b(ad:0x38100000))&0x2)==0x0) rgroup.byte 0x44++0x00 "Bit Count Registers" line.byte 0x00 "TXBITCNT,HSSPI Transmit Bit Count Register" bitfld.byte 0x00 0.--5. " TXBITCNT ,Number of pending transmission bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,?..." else hgroup.byte 0x44++0x00 "Bit Count Registers" hide.byte 0x00 "TXBITCNT,HSSPI Transmit Bit Count Register" endif endif sif (cpu()=="MB86R12")||(cpu()=="MB86R24") if (((per.b(ad:0x38100000+0x34))&0x1)==0x00) rgroup.byte 0x45++0x00 line.byte 0x00 "RXBITCNT,HSSPI Receive Bit Count Register" bitfld.byte 0x00 0.--5. " RXBITCNT ,Number of valid bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,?..." rgroup.long 0x48++0x03 "Shift Register" line.long 0x00 "HSSP_RXSHIFT,HSSPI RX Shift Register" else hgroup.byte 0x45++0x00 hide.byte 0x00 "RXBITCNT,HSSPI Receive Bit Count Register" hgroup.long 0x48++0x03 "Shift Register" hide.long 0x00 "RXSHIFT,HSSPI RX Shift Register" endif endif tree "Tx-FIFO Registers" group.long 0x50++0x3F line.long 0x0 "TXFIFO0,HSSPI TX-FIFO Register 0" line.long 0x4 "TXFIFO1,HSSPI TX-FIFO Register 1" line.long 0x8 "TXFIFO2,HSSPI TX-FIFO Register 2" line.long 0xC "TXFIFO3,HSSPI TX-FIFO Register 3" line.long 0x10 "TXFIFO4,HSSPI TX-FIFO Register 4" line.long 0x14 "TXFIFO5,HSSPI TX-FIFO Register 5" line.long 0x18 "TXFIFO6,HSSPI TX-FIFO Register 6" line.long 0x1C "TXFIFO7,HSSPI TX-FIFO Register 7" line.long 0x20 "TXFIFO8,HSSPI TX-FIFO Register 8" line.long 0x24 "TXFIFO9,HSSPI TX-FIFO Register 9" line.long 0x28 "TXFIFO10,HSSPI TX-FIFO Register 10" line.long 0x2C "TXFIFO11,HSSPI TX-FIFO Register 11" line.long 0x30 "TXFIFO12,HSSPI TX-FIFO Register 12" line.long 0x34 "TXFIFO13,HSSPI TX-FIFO Register 13" line.long 0x38 "TXFIFO14,HSSPI TX-FIFO Register 14" line.long 0x3C "TXFIFO15,HSSPI TX-FIFO Register 15" tree.end tree "Rx-FIFO Registers" hgroup.long 0x90++0x3F hide.long 0x0 "RXFIFO0,HSSPI RX-FIFO Register 0" in hide.long 0x4 "RXFIFO1,HSSPI RX-FIFO Register 1" in hide.long 0x8 "RXFIFO2,HSSPI RX-FIFO Register 2" in hide.long 0xC "RXFIFO3,HSSPI RX-FIFO Register 3" in hide.long 0x10 "RXFIFO4,HSSPI RX-FIFO Register 4" in hide.long 0x14 "RXFIFO5,HSSPI RX-FIFO Register 5" in hide.long 0x18 "RXFIFO6,HSSPI RX-FIFO Register 6" in hide.long 0x1C "RXFIFO7,HSSPI RX-FIFO Register 7" in hide.long 0x20 "RXFIFO8,HSSPI RX-FIFO Register 8" in hide.long 0x24 "RXFIFO9,HSSPI RX-FIFO Register 9" in hide.long 0x28 "RXFIFO10,HSSPI RX-FIFO Register 10" in hide.long 0x2C "RXFIFO11,HSSPI RX-FIFO Register 11" in hide.long 0x30 "RXFIFO12,HSSPI RX-FIFO Register 12" in hide.long 0x34 "RXFIFO13,HSSPI RX-FIFO Register 13" in hide.long 0x38 "RXFIFO14,HSSPI RX-FIFO Register 14" in hide.long 0x3C "RXFIFO15,HSSPI RX-FIFO Register 15" in tree.end group.long 0x4C++0x03 "Configuration Register" line.long 0x00 "FIFOCFG,HSSPI FIFO Configuration Register" bitfld.long 0x00 12. " TXFLSH ,TX-FIFO flush" "No effect,Flush" bitfld.long 0x00 11. " RXFLSH ,RX-FIFO flush" "No effect,Flush" bitfld.long 0x00 10. " TXCTRL ,TXCTRL bit to be written to TX-FIFO" "Low,High" textline " " bitfld.long 0x00 8.--9. " FWIDTH ,TX/RX-FIFO width" "8-bit,16-bit,24-bit,32-bit" bitfld.long 0x00 4.--7. " TXFTH ,TX-FIFO threshold level" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 0.--3. " RXFTH ,RX-FIFO threshold level" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" group.long 0xD0++0x03 "Command Sequencer Register" line.long 0x00 "CSCFG,HSSPI Command Sequencer Configuration Register" bitfld.long 0x00 16.--19. " MSEL ,Memory device selection bits (range of the AHB address space)" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 11. " SSEL3EN ,Slave select 3 enable" "Disabled,Enabled" bitfld.long 0x00 10. " SSEL2EN ,Slave select 2 enable" "Disabled,Enabled" textline " " bitfld.long 0x00 9. " SSEL1EN ,Slave select 1 enable" "Disabled,Enabled" bitfld.long 0x00 8. " SSEL0EN ,Slave select 0 enable" "Disabled,Enabled" bitfld.long 0x00 1.--2. " MBM ,Multi bit mode" "Mode 1,Mode 2,Mode 3,?..." textline " " bitfld.long 0x00 0. " SRAM ,Serial SRAM or serial flash memory type select (Writes disabled/enabled)" "Disabled,Enabled" if (((per.b(ad:0x38100000))&0x02)==0x02) group.long 0xD4++0x07 line.long 0x00 "CSITIME,HSSPI Command Sequencer Idle Time Register" hexmask.long.word 0x00 0.--15. 1. " ITIME ,Idle time" line.long 0x04 "CSAEXT,HSSPI Command Sequencer Address Extension Register" hexmask.long.tbyte 0x04 13.--31. 0x20 " AEXT ,Address extension bits" else hgroup.long 0xD4++0x07 hide.long 0x00 "CSITIME,HSSPI Command Sequencer Idle Time Register" hide.long 0x04 "CSAEXT,HSSPI Command Sequencer Address Extension Register" endif tree "HSSPI Read Command Sequence Data/Control Registers" if ((((per.w(ad:0x38100000+0xDC))&0x1)==0x1)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xDC++0x01 line.word 0x00 "RDCSDC0,HSSPI Read Command Sequence Data/Control Register 0" bitfld.word 0x00 8.--10. " RDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Read transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xDC))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xDC++0x01 line.word 0x00 "RDCSDC0,HSSPI Read Command Sequence Data/Control Register 0" hexmask.word.byte 0x00 8.--15. 1. " RDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Read transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" else hgroup.word 0xDC++0x01 hide.word 0x00 "RDCSDC0,HSSPI Read Command Sequence Data/Control Register 0" endif if ((((per.w(ad:0x38100000+0xDE))&0x1)==0x1)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xDE++0x01 line.word 0x00 "RDCSDC1,HSSPI Read Command Sequence Data/Control Register 1" bitfld.word 0x00 8.--10. " RDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Read transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xDE))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xDE++0x01 line.word 0x00 "RDCSDC1,HSSPI Read Command Sequence Data/Control Register 1" hexmask.word.byte 0x00 8.--15. 1. " RDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Read transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" else hgroup.word 0xDE++0x01 hide.word 0x00 "RDCSDC1,HSSPI Read Command Sequence Data/Control Register 1" endif if ((((per.w(ad:0x38100000+0xE0))&0x1)==0x1)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xE0++0x01 line.word 0x00 "RDCSDC2,HSSPI Read Command Sequence Data/Control Register 2" bitfld.word 0x00 8.--10. " RDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Read transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xE0))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xE0++0x01 line.word 0x00 "RDCSDC2,HSSPI Read Command Sequence Data/Control Register 2" hexmask.word.byte 0x00 8.--15. 1. " RDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Read transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" else hgroup.word 0xE0++0x01 hide.word 0x00 "RDCSDC2,HSSPI Read Command Sequence Data/Control Register 2" endif if ((((per.w(ad:0x38100000+0xE2))&0x1)==0x1)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xE2++0x01 line.word 0x00 "RDCSDC3,HSSPI Read Command Sequence Data/Control Register 3" bitfld.word 0x00 8.--10. " RDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Read transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xE2))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xE2++0x01 line.word 0x00 "RDCSDC3,HSSPI Read Command Sequence Data/Control Register 3" hexmask.word.byte 0x00 8.--15. 1. " RDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Read transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" else hgroup.word 0xE2++0x01 hide.word 0x00 "RDCSDC3,HSSPI Read Command Sequence Data/Control Register 3" endif if ((((per.w(ad:0x38100000+0xE4))&0x1)==0x1)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xE4++0x01 line.word 0x00 "RDCSDC4,HSSPI Read Command Sequence Data/Control Register 4" bitfld.word 0x00 8.--10. " RDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Read transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xE4))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xE4++0x01 line.word 0x00 "RDCSDC4,HSSPI Read Command Sequence Data/Control Register 4" hexmask.word.byte 0x00 8.--15. 1. " RDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Read transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" else hgroup.word 0xE4++0x01 hide.word 0x00 "RDCSDC4,HSSPI Read Command Sequence Data/Control Register 4" endif if ((((per.w(ad:0x38100000+0xE6))&0x1)==0x1)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xE6++0x01 line.word 0x00 "RDCSDC5,HSSPI Read Command Sequence Data/Control Register 5" bitfld.word 0x00 8.--10. " RDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Read transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xE6))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xE6++0x01 line.word 0x00 "RDCSDC5,HSSPI Read Command Sequence Data/Control Register 5" hexmask.word.byte 0x00 8.--15. 1. " RDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Read transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" else hgroup.word 0xE6++0x01 hide.word 0x00 "RDCSDC5,HSSPI Read Command Sequence Data/Control Register 5" endif if ((((per.w(ad:0x38100000+0xE8))&0x1)==0x1)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xE8++0x01 line.word 0x00 "RDCSDC6,HSSPI Read Command Sequence Data/Control Register 6" bitfld.word 0x00 8.--10. " RDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Read transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xE8))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xE8++0x01 line.word 0x00 "RDCSDC6,HSSPI Read Command Sequence Data/Control Register 6" hexmask.word.byte 0x00 8.--15. 1. " RDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Read transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" else hgroup.word 0xE8++0x01 hide.word 0x00 "RDCSDC6,HSSPI Read Command Sequence Data/Control Register 6" endif if ((((per.w(ad:0x38100000+0xEA))&0x1)==0x1)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xEA++0x01 line.word 0x00 "RDCSDC7,HSSPI Read Command Sequence Data/Control Register 7" bitfld.word 0x00 8.--10. " RDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Read transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xEA))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xEA++0x01 line.word 0x00 "RDCSDC7,HSSPI Read Command Sequence Data/Control Register 7" hexmask.word.byte 0x00 8.--15. 1. " RDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Read transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted RDCSDATA[7:0],Decoded RDCSDATA[2:0]" else hgroup.word 0xEA++0x01 hide.word 0x00 "RDCSDC7,HSSPI Read Command Sequence Data/Control Register 7" endif tree.end tree "HSSPI Write Command Sequence Data/Control Registers" if ((((per.w(ad:0x38100000+0xEC))&0x1)==0x01)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xEC++0x01 line.word 0x00 "WDCSDC0,HSSPI Write Command Sequence Data/Control Register 0" bitfld.word 0x00 8.--10. " WDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Write transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xEC))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xEC++0x01 line.word 0x00 "WDCSDC0,HSSPI Write Command Sequence Data/Control Register 0" hexmask.word.byte 0x00 8.--15. 1. " WDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Write transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" else hgroup.word 0xEC++0x01 hide.word 0x00 "WDCSDC0,HSSPI Write Command Sequence Data/Control Register 0" endif if ((((per.w(ad:0x38100000+0xEE))&0x1)==0x01)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xEE++0x01 line.word 0x00 "WDCSDC1,HSSPI Write Command Sequence Data/Control Register 1" bitfld.word 0x00 8.--10. " WDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Write transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xEE))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xEE++0x01 line.word 0x00 "WDCSDC1,HSSPI Write Command Sequence Data/Control Register 1" hexmask.word.byte 0x00 8.--15. 1. " WDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Write transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" else hgroup.word 0xEE++0x01 hide.word 0x00 "WDCSDC1,HSSPI Write Command Sequence Data/Control Register 1" endif if ((((per.w(ad:0x38100000+0xF0))&0x1)==0x01)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xF0++0x01 line.word 0x00 "WDCSDC2,HSSPI Write Command Sequence Data/Control Register 2" bitfld.word 0x00 8.--10. " WDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Write transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xF0))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xF0++0x01 line.word 0x00 "WDCSDC2,HSSPI Write Command Sequence Data/Control Register 2" hexmask.word.byte 0x00 8.--15. 1. " WDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Write transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" else hgroup.word 0xF0++0x01 hide.word 0x00 "WDCSDC2,HSSPI Write Command Sequence Data/Control Register 2" endif if ((((per.w(ad:0x38100000+0xF2))&0x1)==0x01)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xF2++0x01 line.word 0x00 "WDCSDC3,HSSPI Write Command Sequence Data/Control Register 3" bitfld.word 0x00 8.--10. " WDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Write transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xF2))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xF2++0x01 line.word 0x00 "WDCSDC3,HSSPI Write Command Sequence Data/Control Register 3" hexmask.word.byte 0x00 8.--15. 1. " WDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Write transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" else hgroup.word 0xF2++0x01 hide.word 0x00 "WDCSDC3,HSSPI Write Command Sequence Data/Control Register 3" endif if ((((per.w(ad:0x38100000+0xF4))&0x1)==0x01)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xF4++0x01 line.word 0x00 "WDCSDC4,HSSPI Write Command Sequence Data/Control Register 4" bitfld.word 0x00 8.--10. " WDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Write transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xF4))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xF4++0x01 line.word 0x00 "WDCSDC4,HSSPI Write Command Sequence Data/Control Register 4" hexmask.word.byte 0x00 8.--15. 1. " WDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Write transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" else hgroup.word 0xF4++0x01 hide.word 0x00 "WDCSDC4,HSSPI Write Command Sequence Data/Control Register 4" endif if ((((per.w(ad:0x38100000+0xF6))&0x1)==0x01)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xF6++0x01 line.word 0x00 "WDCSDC5,HSSPI Write Command Sequence Data/Control Register 5" bitfld.word 0x00 8.--10. " WDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Write transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xF6))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xF6++0x01 line.word 0x00 "WDCSDC5,HSSPI Write Command Sequence Data/Control Register 5" hexmask.word.byte 0x00 8.--15. 1. " WDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Write transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" else hgroup.word 0xF6++0x01 hide.word 0x00 "WDCSDC5,HSSPI Write Command Sequence Data/Control Register 5" endif if ((((per.w(ad:0x38100000+0xF8))&0x1)==0x01)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xF8++0x01 line.word 0x00 "WDCSDC6,HSSPI Write Command Sequence Data/Control Register 6" bitfld.word 0x00 8.--10. " WDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Write transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xF8))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xF8++0x01 line.word 0x00 "WDCSDC6,HSSPI Write Command Sequence Data/Control Register 6" hexmask.word.byte 0x00 8.--15. 1. " WDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Write transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" else hgroup.word 0xF8++0x01 hide.word 0x00 "WDCSDC6,HSSPI Write Command Sequence Data/Control Register 6" endif if ((((per.w(ad:0x38100000+0xFA))&0x1)==0x01)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xFA++0x01 line.word 0x00 "WDCSDC7,HSSPI Write Command Sequence Data/Control Register 7" bitfld.word 0x00 8.--10. " WDCSDATA[2:0] ,Command sequencer data or control byte for Memory-Write transactions" "Bits [7:0],Bits [15:8],Bits [23:16],Bits [31:24],High-Z byte,High-Z nibble,,End of list" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" elif ((((per.w(ad:0x38100000+0xFA))&0x1)==0x00)&&(((per.b(ad:0x38100000))&0x02)==0x02)) group.word 0xFA++0x01 line.word 0x00 "WDCSDC7,HSSPI Write Command Sequence Data/Control Register 7" hexmask.word.byte 0x00 8.--15. 1. " WDCSDATA[7:0] ,Command sequencer data or control byte for Memory-Write transactions" bitfld.word 0x00 0. " DEC ,Decode" "Transmitted WDCSDATA[7:0],Decoded WDCSDATA[2:0]" else hgroup.word 0xFA++0x01 hide.word 0x00 "WDCSDC7,HSSPI Write Command Sequence Data/Control Register 7" endif tree.end rgroup.long 0xFC++0x03 "Module ID Register" line.long 0x00 "MID,HSSPI Module ID Register" width 12. tree.end tree "WDT (Watchdog)" sif (cpuis("MB86R11F")) tree "WDT A" base ad:0x3b100000 width 14. if (((per.l(ad:0x3b100000+0xC00))&0xFFFFFFFF)==0x00) group.long 0x00++0x03 line.long 0x00 "WDG_LOAD,Watchdog Load Register" rgroup.long 0x04++0x03 line.long 0x00 "WDG_VALUE,Watchdog Value Register" group.long 0x08++0x03 line.long 0x00 "WDG_CONTROL,Watchdog Cotrol Register" bitfld.long 0x00 1. " RESEN ,Enable Watchdog module reset output" "Disabled,Enabled" bitfld.long 0x00 0. " INTEN ,Enable the interrupt event" "Disabled,Enabled" wgroup.long 0x0C++0x03 line.long 0x00 "WDG_INT_CLR,Watchdog Interrupt Clear Register" rgroup.long 0x10++0x07 line.long 0x00 "WDG_RIS,Watchdog Raw Interrupt Status Register" bitfld.long 0x00 0. " WDOGRIS ,Raw interrupt status from the counter" "No interrupt,Interrupt" line.long 0x04 "WDG_MIS,Watchdog Masked Interrupt Status Register" bitfld.long 0x04 0. " WDOGMIS ,Enabled interrupt status from the counter" "Disabled,Enabled" else rgroup.long 0x00++0x03 line.long 0x00 "WDG_LOAD,Watchdog Load Register" rgroup.long 0x04++0x03 line.long 0x00 "WDG_VALUE,Watchdog Value Register" rgroup.long 0x08++0x03 line.long 0x00 "WDG_CONTROL,Watchdog Cotrol Register" bitfld.long 0x00 1. " RESEN ,Enable Watchdog module reset output" "Disabled,Enabled" bitfld.long 0x00 0. " INTEN ,Enable the interrupt event" "Disabled,Enabled" hgroup.long 0x0C++0x03 hide.long 0x00 "WDG_INT_CLR,Watchdog Interrupt Clear Register" rgroup.long 0x10++0x07 line.long 0x00 "WDG_RIS,Watchdog Raw Interrupt Status Register" bitfld.long 0x00 0. " WDOGRIS ,Raw interrupt status from the counter" "No interrupt,Interrupt" line.long 0x04 "WDG_MIS,Watchdog Masked Interrupt Status Register" bitfld.long 0x04 0. " WDOGMIS ,Enabled interrupt status from the counter" "Disabled,Enabled" endif group.long 0xC00++0x03 line.long 0x00 "WDG_LOCK,Watchdog Lock Register" if (((per.l(ad:0x3b100000+0xC00))&0xFFFFFFFF)==0x00) rgroup.long 0xFE0++0x1F line.long 0x00 "WDG_PERIPHLD0,Watchdog Peripherial Identification Register 0" hexmask.long.byte 0x00 0.--7. 1. " PARTNUMBER0 ,Part Number 0" line.long 0x04 "WDG_PERIPHLD1,Watchdog Peripherial Identification Register 1" bitfld.long 0x04 4.--7. " DESIGNER0 ,Designer 0" ",1,?..." bitfld.long 0x04 0.--3. " PARTNUMBER1 ,Part Number 1" ",,,,,,,,8,?..." line.long 0x08 "WDG_PERIPHLD2,Watchdog Peripherial Identification Register 2" bitfld.long 0x08 4.--7. " REVISION ,Revision" ",1,?..." bitfld.long 0x08 0.--3. " DESIGNER1 ,Designer 1" ",,,,4,?..." line.long 0x0C "WDG_PERIPHLD4,Watchdog Peripherial Identification Register 4" hexmask.long.byte 0x0C 0.--7. 1. " CONFIGURATION ,Configuration" line.long 0x10 "WDG_PCELLID0,Watchdog PrimeCell Identification Register 0" hexmask.long.byte 0x10 0.--7. 1. " WDOGPCELLID0 ,Watchdog PrimeCell Identification 0" line.long 0x14 "WDG_PCELLID1,Watchdog PrimeCell Identification Register 1" hexmask.long.byte 0x14 0.--7. 1. " WDOGPCELLID1 ,Watchdog PrimeCell Identification 1" line.long 0x18 "WDG_PCELLID2,Watchdog PrimeCell Identification Register 2" hexmask.long.byte 0x18 0.--7. 1. " WDOGPCELLID2 ,Watchdog PrimeCell Identification 2" line.long 0x1C "WDG_PCELLID3,Watchdog PrimeCell Identification Register 3" hexmask.long.byte 0x1C 0.--7. 1. " WDOGPCELLID3 ,Watchdog PrimeCell Identification 3" group.long 0xF00++0x03 line.long 0x00 "WDG_ITCR,Watchdog Integration Test Control Register" bitfld.long 0x00 0. " ITEN ,Integration test enable" "Normal mode,Integration mode" if (((per.l(ad:0x3b100000+0xF00))&0x01)==0x01) wgroup.long 0xF04++0x03 line.long 0x00 "WDG_ITOP,Watchdog Integration Test Output Set Register" bitfld.long 0x00 1. " WDOGINT ,Watchdog interrupt output" "No interrupt,Interrupt" bitfld.long 0x00 0. " WDOGRES ,Watchdog reset output" "No reset,Reset" else hgroup.long 0xF04++0x03 hide.long 0x00 "WDG_ITOP,Watchdog Integration Test Output Set Register" endif else rgroup.long 0xFE0++0x1F line.long 0x00 "WDG_PERIPHLD0,Watchdog Peripherial Identification Register 0" hexmask.long.byte 0x00 0.--7. 1. " PARTNUMBER0 ,Part Number 0" line.long 0x04 "WDG_PERIPHLD1,Watchdog Peripherial Identification Register 1" bitfld.long 0x04 4.--7. " DESIGNER0 ,Designer 0" ",1,?..." bitfld.long 0x04 0.--3. " PARTNUMBER1 ,Part Number 1" ",,,,,,,,8,?..." line.long 0x08 "WDG_PERIPHLD2,Watchdog Peripherial Identification Register 2" bitfld.long 0x08 4.--7. " REVISION ,Revision" ",1,?..." bitfld.long 0x08 0.--3. " DESIGNER1 ,Designer 1" ",,,,4,?..." line.long 0x0C "WDG_PERIPHLD4,Watchdog Peripherial Identification Register 4" hexmask.long.byte 0x0C 0.--7. 1. " CONFIGURATION ,Configuration" line.long 0x10 "WDG_PCELLID0,Watchdog PrimeCell Identification Register 0" hexmask.long.byte 0x10 0.--7. 1. " WDOGPCELLID0 ,Watchdog PrimeCell Identification 0" line.long 0x14 "WDG_PCELLID1,Watchdog PrimeCell Identification Register 1" hexmask.long.byte 0x14 0.--7. 1. " WDOGPCELLID1 ,Watchdog PrimeCell Identification 1" line.long 0x18 "WDG_PCELLID2,Watchdog PrimeCell Identification Register 2" hexmask.long.byte 0x18 0.--7. 1. " WDOGPCELLID2 ,Watchdog PrimeCell Identification 2" line.long 0x1C "WDG_PCELLID3,Watchdog PrimeCell Identification Register 3" hexmask.long.byte 0x1C 0.--7. 1. " WDOGPCELLID3 ,Watchdog PrimeCell Identification 3" rgroup.long 0xF00++0x03 line.long 0x00 "WDG_ITCR,Watchdog Integration Test Control Register" bitfld.long 0x00 0. " ITEN ,Integration test enable" "Normal mode,Integration mode" hgroup.long 0xF04++0x03 hide.long 0x00 "WDG_ITOP,Watchdog Integration Test Output Set Register" endif width 0x0B tree.end endif tree "WDT B" base ad:0x04A00000 width 14. group.long 0x00++0x03 line.long 0x00 "PROT,Watchdog Protection Register" if (((per.l(ad:0x04A00000))&0xFFFFFFFF)==0xFFFFFFFF) rgroup.long 0x08++0x03 line.long 0x00 "CNT,Watchdog Counter Register" group.long 0x0C++0x03 line.long 0x00 "RSTCAUSE,Watchdog Reset Cause Register" bitfld.long 0x00 4. " RSTCAUSE4 ,Reset cause 4" "Not triggered,Triggered" bitfld.long 0x00 3. " RSTCAUSE3 ,Reset cause 3" "Not triggered,Triggered" bitfld.long 0x00 2. " RSTCAUSE2 ,Reset cause 2" "Not triggered,Triggered" textline " " bitfld.long 0x00 1. " RSTCAUSE1 ,Reset cause 1" "Not triggered,Triggered" bitfld.long 0x00 0. " RSTCAUSE0 ,Reset cause 0" "Not triggered,Triggered" wgroup.long 0x10++0x03 line.long 0x00 "TRG0,Watchdog Trigger 0 Register" hexmask.long.byte 0x00 0.--7. 1. " WDGTRG0 ,Watchdog trigger 0" wgroup.long 0x18++0x03 line.long 0x00 "TRG1,Watchdog Trigger 1 Register" hexmask.long.byte 0x00 0.--7. 1. " WDGTRG1 ,Watchdog trigger 1" group.long 0x20++0x03 line.long 0x00 "INT,Watchdog Interrupt Configuration Register" bitfld.long 0x00 17. " INT_EN ,Reset/NMI configuration" "Reset,INT" bitfld.long 0x00 16. " PRE_EN ,Prewarn interrupt enable" "Disabled,Enabled" rbitfld.long 0x00 1. " INT_FLAG ,INT flag" "No error,Error" textline " " rbitfld.long 0x00 0. " PRE_FLAG ,Prewarn interrupt flag" "No error,Error" wgroup.long 0x24++0x03 line.long 0x00 "INTCLR,Watchdog Interrupt Clear Register" bitfld.long 0x00 1. " INT_CLR ,INT clear bit" "No effect,Clear" bitfld.long 0x00 0. " PRE_CLR ,Prewarn interrupt clear" "No effect,Clear" group.long 0x2C++0x17 line.long 0x00 "TRG0CFG,Watchdog Trigger 0 Configuration Register" hexmask.long.byte 0x00 0.--7. 1. " WDGTRG0CFG ,Watchdog trigger 0 configuration" line.long 0x04 "TRG1CFG,Watchdog Trigger 1 Configuration Register" hexmask.long.byte 0x04 0.--7. 1. " WDGTRG1CFG ,Watchdog trigger 1 configuration" line.long 0x08 "RUNLL,Watchdog Lower Limit RUN Register" line.long 0x0C "RUNUL,Watchdog Upper Limit RUN Register" sif (cpu()=="MB86R24") group.long 0x3C++0x07 line.long 0x00 "PSSLL,PSSLL Register" line.long 0x04 "PSSUL,PSSUL Register" endif wgroup.long 0x44++0x03 line.long 0x00 "RSTDLY,Watchdog Reset Delay Counter Register" hexmask.long.word 0x00 0.--15. 1. " WDGRSTDLY ,Delay to Reset/NMI" sif (cpu()=="MB86R24") group.long 0x48++0x03 line.long 0x00 "CFG,Configuration Register" bitfld.long 0x00 24. " LOCK ,Lock" "Not locked,Locked" bitfld.long 0x00 16.--20. " OBSSEL ,Observe bits of watchdog counter" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32" bitfld.long 0x00 8.--9. " CLKSEL ,Clock selection bits" "RC,Slow RC,Sub,Main" textline " " bitfld.long 0x00 3. " DBGEN ,Debug enable" "Disabled,Enabled" bitfld.long 0x00 2. " ALLOWSTOPCLK ,Configuration to stop the clock" "Cannot be stopped,Can be stopped" bitfld.long 0x00 1. " WDENPSS ,Enable bit for watchdog counter in PSS state" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " WDENRUN ,Enable bit for watchdog counter in RUN state" "Disabled,Enabled" else group.long 0x48++0x03 line.long 0x00 "CFG,Watchdog Configuration Register" bitfld.long 0x00 24. " LOCK ,Lock" "Not locked,Locked" bitfld.long 0x00 0. " WDENRUN ,Enable bit for watchdog counter in RUN state" "Disabled,Enabled" endif else rgroup.long 0x08++0x07 line.long 0x00 "CNT,Watchdog Counter Register" line.long 0x04 "RSTCAUSE,Watchdog Reset Cause Register" bitfld.long 0x04 4. " RSTCAUSE4 ,Reset cause 4" "Not triggered,Triggered" bitfld.long 0x04 3. " RSTCAUSE3 ,Reset cause 3" "Not triggered,Triggered" bitfld.long 0x04 2. " RSTCAUSE2 ,Reset cause 2" "Not triggered,Triggered" textline " " bitfld.long 0x04 1. " RSTCAUSE1 ,Reset cause 1" "Not triggered,Triggered" bitfld.long 0x04 0. " RSTCAUSE0 ,Reset cause 0" "Not triggered,Triggered" hgroup.long 0x10++0x03 hide.long 0x00 "TRG0,Watchdog Trigger 0 Register" hgroup.long 0x18++0x03 hide.long 0x00 "TRG1,Watchdog Trigger 1 Register" rgroup.long 0x20++0x03 line.long 0x00 "INT,Watchdog Interrupt Configuration Register" bitfld.long 0x00 17. " INT_EN ,Reset/NMI configuration" "Reset,INT" bitfld.long 0x00 16. " PRE_EN ,Prewarn interrupt enable" "Disabled,Enabled" rbitfld.long 0x00 1. " INT_FLAG ,INT flag" "No error,Error" textline " " rbitfld.long 0x00 0. " PRE_FLAG ,Prewarn interrupt flag" "No error,Error" hgroup.long 0x24++0x03 hide.long 0x00 "INTCLR,Watchdog Interrupt Clear Register" rgroup.long 0x2C++0x17 line.long 0x00 "TRG0CFG,Watchdog Trigger 0 Configuration Register" hexmask.long.byte 0x00 0.--7. 1. " WDGTRG0CFG ,Watchdog trigger 0 configuration" line.long 0x04 "TRG1CFG,Watchdog Trigger 1 Configuration Register" hexmask.long.byte 0x04 0.--7. 1. " WDGTRG1CFG ,Watchdog trigger 1 configuration" line.long 0x08 "RUNLL,Watchdog Lower Limit RUN Register" line.long 0x0C "RUNUL,Watchdog Upper Limit RUN Register" sif (cpu()=="MB86R24") rgroup.long 0x3C++0x07 line.long 0x00 "PSSLL,PSSLL Register" line.long 0x04 "PSSUL,PSSUL Register" endif hgroup.long 0x44++0x03 hide.long 0x00 "RSTDLY,Watchdog Reset Delay Counter Register" textline " " sif (cpu()=="MB86R24") rgroup.long 0x48++0x03 line.long 0x00 "CFG,Configuration Register" bitfld.long 0x00 24. " LOCK ,Lock" "Not locked,Locked" bitfld.long 0x00 16.--20. " OBSSEL ,Observe bits of watchdog counter" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32" bitfld.long 0x00 8.--9. " CLKSEL ,Clock selection bits" "RC,Slow RC,Sub,Main" textline " " bitfld.long 0x00 3. " DBGEN ,Debug enable" "Disabled,Enabled" bitfld.long 0x00 2. " ALLOWSTOPCLK ,Configuration to stop the clock" "Cannot be stopped,Can be stopped" bitfld.long 0x00 1. " WDENPSS ,Enable bit for watchdog counter in PSS state" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " WDENRUN ,Enable bit for watchdog counter in RUN state" "Disabled,Enabled" else rgroup.long 0x48++0x03 line.long 0x00 "CFG,Watchdog Configuration Register" bitfld.long 0x00 24. " LOCK ,Lock" "Not locked,Locked" bitfld.long 0x00 0. " WDENRUN ,Enable bit for watchdog counter in RUN state" "Disabled,Enabled" endif endif width 0x0B tree.end tree.end tree "PMU (Power Management Unit)" base ad:0x3D000000 width 14. group.long 0x00++0x03 line.long 0x00 "PMU_CTL,Power Management Unit Control Register" hexmask.long.byte 0x00 8.--15. 1. " SETEN ,SETEN" eventfld.long 0x00 2. " ADSET ,All down set" "No,Yes" eventfld.long 0x00 1. " PDSET ,Power down set" "No,Yes" textline " " eventfld.long 0x00 0. " PUSET ,Power up set" "No,Yes" rgroup.long 0x04++0x03 line.long 0x00 "PMU_MSR,Power Management Unit Mode Status Register" bitfld.long 0x00 15. " WTOFFSEL ,Weak-PSW-Tr off select" "On,Off" bitfld.long 0x00 11. " RSTSEL ,Reset select" "Off,On" group.long 0x08++0x03 line.long 0x00 "PMU_INT_EN,Power Management Unit Interrupt Enable Register" bitfld.long 0x00 6. " PDIE ,Power down interrupt enable" "Disabled,Enabled" bitfld.long 0x00 5. " PDNIE ,Power-switch-down done interrupt enable" "Disabled,Enabled" bitfld.long 0x00 4. " PONIE ,Power-switch-on done interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " WUIE1 ,Wake up interrupt enable1" "Disabled,Enabled" bitfld.long 0x00 0. " WUIE0 ,Wake up interrupt enable0" "Disabled,Enabled" rgroup.long 0x0C++0x03 line.long 0x00 "PMU_INT_ST,Power Management Unit Interrupt Status Register" bitfld.long 0x00 6. " PDI ,Power down interrupt occurred" "No interrupt,Interrupt" bitfld.long 0x00 5. " PDNI ,Power-switch-down done interrupt occurred" "No interrupt,Interrupt" bitfld.long 0x00 4. " PONI ,Power-switch-ON done interrupt occurred" "No interrupt,Interrupt" textline " " bitfld.long 0x00 1. " WUI1 ,Wake up interrupt1 occurred" "No interrupt,Interrupt" bitfld.long 0x00 0. " WUI0 ,Wake up interrupt0 occurred" "No interrupt,Interrupt" wgroup.long 0x10++0x03 line.long 0x00 "PMU_INT_CLR,Power Management Unit Interrupt Clear Register" bitfld.long 0x00 6. " PDIC ,Power down interrupt clear" "No effect,Clear" bitfld.long 0x00 5. " PDNIC ,Power-switch-down done interrupt clear" "No effect,Clear" bitfld.long 0x00 4. " PONIC ,Power-switch-on done interrupt clear" "No effect,Clear" textline " " bitfld.long 0x00 1. " WUIC1 ,Wake up interrupt1 clear" "No effect,Clear" bitfld.long 0x00 0. " WUIC0 ,Wake up interrupt1 clear" "No effect,Clear" rgroup.long 0x14++0x07 line.long 0x00 "PMU_STR,Power Management Unit Status Register" bitfld.long 0x00 15. " PWR_SW ,Power switch" "0,1" bitfld.long 0x00 0. " PMU_ST ,PMU status" "0,1" line.long 0x04 "PWR_STR,Power Status Register" bitfld.long 0x04 15. " PWR_STATUS15 ,Power-on PD16" "Off,On" bitfld.long 0x04 14. " PWR_STATUS14 ,Power-on PD15" "Off,On" bitfld.long 0x04 13. " PWR_STATUS13 ,Power-on PD14" "Off,On" textline " " bitfld.long 0x04 12. " PWR_STATUS12 ,Power-on PD13" "Off,On" bitfld.long 0x04 11. " PWR_STATUS11 ,Power-on PD12" "Off,On" bitfld.long 0x04 10. " PWR_STATUS10 ,Power-on PD11" "Off,On" textline " " bitfld.long 0x04 9. " PWR_STATUS9 ,Power-on PD10" "Off,On" bitfld.long 0x04 8. " PWR_STATUS8 ,Power-on PD9" "Off,On" bitfld.long 0x04 7. " PWR_STATUS7 ,Power-on PD8" "Off,On" textline " " bitfld.long 0x04 6. " PWR_STATUS6 ,Power-on PD7" "Off,On" bitfld.long 0x04 5. " PWR_STATUS5 ,Power-on PD6" "Off,On" bitfld.long 0x04 4. " PWR_STATUS4 ,Power-on PD5" "Off,On" textline " " bitfld.long 0x04 3. " PWR_STATUS3 ,Power-on PD4" "Off,On" bitfld.long 0x04 2. " PWR_STATUS2 ,Power-on PD3" "Off,On" bitfld.long 0x04 1. " PWR_STATUS1 ,Power-on PD2" "Off,On" textline " " bitfld.long 0x04 0. " PWR_STATUS0 ,Power-on PD1" "Off,On" group.long 0x20++0x03 line.long 0x00 "PWR_ON_EN0,Power On Enable 0 Register" bitfld.long 0x00 15. " PON_EN15 ,Power on PD16" "Disabled,Enabled" bitfld.long 0x00 14. " PON_EN14 ,Power on PD15" "Disabled,Enabled" bitfld.long 0x00 13. " PON_EN13 ,Power on PD14" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " PON_EN12 ,Power on PD13" "Disabled,Enabled" bitfld.long 0x00 11. " PON_EN11 ,Power on PD12" "Disabled,Enabled" bitfld.long 0x00 10. " PON_EN10 ,Power on PD11" "Disabled,Enabled" textline " " bitfld.long 0x00 9. " PON_EN9 ,Power on PD10" "Disabled,Enabled" bitfld.long 0x00 8. " PON_EN8 ,Power on PD9" "Disabled,Enabled" bitfld.long 0x00 7. " PON_EN7 ,Power on PD8" "Disabled,Enabled" textline " " bitfld.long 0x00 6. " PON_EN6 ,Power on PD7" "Disabled,Enabled" bitfld.long 0x00 5. " PON_EN5 ,Power on PD6" "Disabled,Enabled" bitfld.long 0x00 4. " PON_EN4 ,Power on PD5" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " PON_EN3 ,Power on PD4" "Disabled,Enabled" bitfld.long 0x00 2. " PON_EN2 ,Power on PD3" "Disabled,Enabled" bitfld.long 0x00 1. " PON_EN1 ,Power on PD2" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " PON_EN0 ,Power on PD1" "Disabled,Enabled" group.long 0x28++0x03 line.long 0x00 "PWR_ON_EN1,Power On Enable 1 Register" bitfld.long 0x00 15. " PON_EN15 ,Power on PD16" "Disabled,Enabled" bitfld.long 0x00 14. " PON_EN14 ,Power on PD15" "Disabled,Enabled" bitfld.long 0x00 13. " PON_EN13 ,Power on PD14" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " PON_EN12 ,Power on PD13" "Disabled,Enabled" bitfld.long 0x00 11. " PON_EN11 ,Power on PD12" "Disabled,Enabled" bitfld.long 0x00 10. " PON_EN10 ,Power on PD11" "Disabled,Enabled" textline " " bitfld.long 0x00 9. " PON_EN9 ,Power on PD10" "Disabled,Enabled" bitfld.long 0x00 8. " PON_EN8 ,Power on PD9" "Disabled,Enabled" bitfld.long 0x00 7. " PON_EN7 ,Power on PD8" "Disabled,Enabled" textline " " bitfld.long 0x00 6. " PON_EN6 ,Power on PD7" "Disabled,Enabled" bitfld.long 0x00 5. " PON_EN5 ,Power on PD6" "Disabled,Enabled" bitfld.long 0x00 4. " PON_EN4 ,Power on PD5" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " PON_EN3 ,Power on PD4" "Disabled,Enabled" bitfld.long 0x00 2. " PON_EN2 ,Power on PD3" "Disabled,Enabled" bitfld.long 0x00 1. " PON_EN1 ,Power on PD2" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " PON_EN0 ,Power on PD1" "Disabled,Enabled" group.long 0x40++0x03 line.long 0x00 "PWR_DN_EN,Power Down Enable Register" bitfld.long 0x00 15. " PDOWN_EN15 ,Power down PD16" "Disabled,Enabled" bitfld.long 0x00 14. " PDOWN_EN14 ,Power down PD15" "Disabled,Enabled" bitfld.long 0x00 13. " PDOWN_EN13 ,Power down PD14" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " PDOWN_EN12 ,Power down PD13" "Disabled,Enabled" bitfld.long 0x00 11. " PDOWN_EN11 ,Power down PD12" "Disabled,Enabled" bitfld.long 0x00 10. " PDOWN_EN10 ,Power down PD11" "Disabled,Enabled" textline " " bitfld.long 0x00 9. " PDOWN_EN9 ,Power down PD10" "Disabled,Enabled" bitfld.long 0x00 8. " PDOWN_EN8 ,Power down PD9" "Disabled,Enabled" bitfld.long 0x00 7. " PDOWN_EN7 ,Power down PD8" "Disabled,Enabled" textline " " bitfld.long 0x00 6. " PDOWN_EN6 ,Power down PD7" "Disabled,Enabled" bitfld.long 0x00 5. " PDOWN_EN5 ,Power down PD6" "Disabled,Enabled" bitfld.long 0x00 4. " PDOWN_EN4 ,Power down PD5" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " PDOWN_EN3 ,Power down PD4" "Disabled,Enabled" bitfld.long 0x00 2. " PDOWN_EN2 ,Power down PD3" "Disabled,Enabled" bitfld.long 0x00 1. " PDOWN_EN1 ,Power down PD2" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " PDOWN_EN0 ,Power down PD1" "Disabled,Enabled" group.long 0x50++0x03 line.long 0x00 "PWR_ON_CYC,Power On Cycle Register" sif (cpu()=="MB86R24") bitfld.long 0x00 0.--2. " PWR_ON_CYC ,Power on cycle" "64CLK of PMUCLK,128 CLK,256 CLK,512 CLK,1024 CLK,2048 CLK,4096 CLK,8192 CLK" else bitfld.long 0x00 0.--2. " PWR_ON_CYC ,Power on cycle" "64CLK of RTCLK,128 CLK,256 CLK,512 CLK,1024 CLK,2048 CLK,4096 CLK,8192 CLK" endif group.long 0x58++0x03 line.long 0x00 "PWR_CYC_SEL,Power Cycle Select Register" bitfld.long 0x00 15. " PWR_CYC_SEL15 ,Power cycle PD16" "PWR_TM_CTL,PWR_ON_CYC" bitfld.long 0x00 14. " PWR_CYC_SEL14 ,Power cycle PD15" "PWR_TM_CTL,PWR_ON_CYC" bitfld.long 0x00 13. " PWR_CYC_SEL13 ,Power cycle PD14" "PWR_TM_CTL,PWR_ON_CYC" textline " " bitfld.long 0x00 12. " PWR_CYC_SEL12 ,Power cycle PD13" "PWR_TM_CTL,PWR_ON_CYC" bitfld.long 0x00 11. " PWR_CYC_SEL11 ,Power cycle PD12" "PWR_TM_CTL,PWR_ON_CYC" bitfld.long 0x00 10. " PWR_CYC_SEL10 ,Power cycle PD11" "PWR_TM_CTL,PWR_ON_CYC" textline " " bitfld.long 0x00 9. " PWR_CYC_SEL9 ,Power cycle PD10" "PWR_TM_CTL,PWR_ON_CYC" bitfld.long 0x00 8. " PWR_CYC_SEL8 ,Power cycle PD9" "PWR_TM_CTL,PWR_ON_CYC" bitfld.long 0x00 7. " PWR_CYC_SEL7 ,Power cycle PD8" "PWR_TM_CTL,PWR_ON_CYC" textline " " bitfld.long 0x00 6. " PWR_CYC_SEL6 ,Power cycle PD7" "PWR_TM_CTL,PWR_ON_CYC" bitfld.long 0x00 5. " PWR_CYC_SEL5 ,Power cycle PD6" "PWR_TM_CTL,PWR_ON_CYC" bitfld.long 0x00 4. " PWR_CYC_SEL4 ,Power cycle PD5" "PWR_TM_CTL,PWR_ON_CYC" textline " " bitfld.long 0x00 3. " PWR_CYC_SEL3 ,Power cycle PD4" "PWR_TM_CTL,PWR_ON_CYC" bitfld.long 0x00 2. " PWR_CYC_SEL2 ,Power cycle PD3" "PWR_TM_CTL,PWR_ON_CYC" bitfld.long 0x00 1. " PWR_CYC_SEL1 ,Power cycle PD2" "PWR_TM_CTL,PWR_ON_CYC" textline " " bitfld.long 0x00 0. " PWR_CYC_SEL0 ,Power cycle PD1" "PWR_TM_CTL,PWR_ON_CYC" group.long 0x60++0x03 line.long 0x00 "PWR_DLY_CTL0,Power Delay Control Register 0" bitfld.long 0x00 12.--15. " PON3 ,Power on timing setting register 3" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 8.--11. " PON2 ,Power on timing setting register 2" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 4.--7. " PON1 ,Power on timing setting register 1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 0.--3. " PON0 ,Power on timing setting register 0" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" rgroup.long (0x60+0x20)++0x03 line.long 0x00 "PWR_TM_CTL0,Power Timing Control Register 0" bitfld.long 0x00 12.--14. " PTC3 ,Power on timing cycle setting register 3" "0,1,2,3,4,5,6,7" bitfld.long 0x00 8.--10. " PTC2 ,Power on timing cycle setting register 2" "0,1,2,3,4,5,6,7" bitfld.long 0x00 4.--6. " PTC1 ,Power on timing cycle setting register 1" "0,1,2,3,4,5,6,7" textline " " sif (cpu()=="MB86R12")||(cpu()=="MB86R24") bitfld.long 0x00 4.--6. " PTC0 ,Power on timing cycle setting register 0 Tdiff/Tstart" "0.5/0.5,1.5/1.5,2.5/2.5,4.5/4.5,,1.5/0.5,2.5/1.5,4.5/2.5" else bitfld.long 0x00 4.--6. " PTC0 ,Power on timing cycle setting register 0 Tdiff/Tstart" "0.5/0.5,1.5/1.5,2.5/2.5,4.5/4.5,,1.5/0.5,2.5/1.5,4.5/1.5" endif group.long 0x64++0x03 line.long 0x00 "PWR_DLY_CTL1,Power Delay Control Register 1" bitfld.long 0x00 12.--15. " PON7 ,Power on timing setting register 3" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 8.--11. " PON6 ,Power on timing setting register 2" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 4.--7. " PON5 ,Power on timing setting register 1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 0.--3. " PON4 ,Power on timing setting register 0" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" rgroup.long (0x64+0x20)++0x03 line.long 0x00 "PWR_TM_CTL1,Power Timing Control Register 1" bitfld.long 0x00 12.--14. " PTC7 ,Power on timing cycle setting register 3" "0,1,2,3,4,5,6,7" bitfld.long 0x00 8.--10. " PTC6 ,Power on timing cycle setting register 2" "0,1,2,3,4,5,6,7" bitfld.long 0x00 4.--6. " PTC5 ,Power on timing cycle setting register 1" "0,1,2,3,4,5,6,7" textline " " sif (cpu()=="MB86R12")||(cpu()=="MB86R24") bitfld.long 0x00 4.--6. " PTC4 ,Power on timing cycle setting register 0 Tdiff/Tstart" "0.5/0.5,1.5/1.5,2.5/2.5,4.5/4.5,,1.5/0.5,2.5/1.5,4.5/2.5" else bitfld.long 0x00 4.--6. " PTC4 ,Power on timing cycle setting register 0 Tdiff/Tstart" "0.5/0.5,1.5/1.5,2.5/2.5,4.5/4.5,,1.5/0.5,2.5/1.5,4.5/1.5" endif group.long 0x68++0x03 line.long 0x00 "PWR_DLY_CTL2,Power Delay Control Register 2" bitfld.long 0x00 12.--15. " PON11 ,Power on timing setting register 3" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 8.--11. " PON10 ,Power on timing setting register 2" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 4.--7. " PON9 ,Power on timing setting register 1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 0.--3. " PON8 ,Power on timing setting register 0" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" rgroup.long (0x68+0x20)++0x03 line.long 0x00 "PWR_TM_CTL2,Power Timing Control Register 2" bitfld.long 0x00 12.--14. " PTC11 ,Power on timing cycle setting register 3" "0,1,2,3,4,5,6,7" bitfld.long 0x00 8.--10. " PTC10 ,Power on timing cycle setting register 2" "0,1,2,3,4,5,6,7" bitfld.long 0x00 4.--6. " PTC9 ,Power on timing cycle setting register 1" "0,1,2,3,4,5,6,7" textline " " sif (cpu()=="MB86R12")||(cpu()=="MB86R24") bitfld.long 0x00 4.--6. " PTC8 ,Power on timing cycle setting register 0 Tdiff/Tstart" "0.5/0.5,1.5/1.5,2.5/2.5,4.5/4.5,,1.5/0.5,2.5/1.5,4.5/2.5" else bitfld.long 0x00 4.--6. " PTC8 ,Power on timing cycle setting register 0 Tdiff/Tstart" "0.5/0.5,1.5/1.5,2.5/2.5,4.5/4.5,,1.5/0.5,2.5/1.5,4.5/1.5" endif group.long 0x6C++0x03 line.long 0x00 "PWR_DLY_CTL3,Power Delay Control Register 3" bitfld.long 0x00 12.--15. " PON15 ,Power on timing setting register 3" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 8.--11. " PON14 ,Power on timing setting register 2" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 4.--7. " PON13 ,Power on timing setting register 1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 0.--3. " PON12 ,Power on timing setting register 0" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" rgroup.long (0x6C+0x20)++0x03 line.long 0x00 "PWR_TM_CTL3,Power Timing Control Register 3" bitfld.long 0x00 12.--14. " PTC15 ,Power on timing cycle setting register 3" "0,1,2,3,4,5,6,7" bitfld.long 0x00 8.--10. " PTC14 ,Power on timing cycle setting register 2" "0,1,2,3,4,5,6,7" bitfld.long 0x00 4.--6. " PTC13 ,Power on timing cycle setting register 1" "0,1,2,3,4,5,6,7" textline " " sif (cpu()=="MB86R12")||(cpu()=="MB86R24") bitfld.long 0x00 4.--6. " PTC12 ,Power on timing cycle setting register 0 Tdiff/Tstart" "0.5/0.5,1.5/1.5,2.5/2.5,4.5/4.5,,1.5/0.5,2.5/1.5,4.5/2.5" else bitfld.long 0x00 4.--6. " PTC12 ,Power on timing cycle setting register 0 Tdiff/Tstart" "0.5/0.5,1.5/1.5,2.5/2.5,4.5/4.5,,1.5/0.5,2.5/1.5,4.5/1.5" endif width 0x0B tree.end tree "TS (Transport Stream Interface)" base ad:0xC0000000 width 29. tree "Input Buffer" group.long 0x24014++0x03 line.long 0x00 "TSD1_INPUT_CFG,Input configuration" hexmask.long.byte 0x00 24.--31. 1. " SYNC_BYTE_DISTANCE ,Distance between Sync Bytes" bitfld.long 0x00 20.--21. " INPUT_SELECT ,Select the input channel" "A,B,C,C" bitfld.long 0x00 19. " PACKET_BUF_OVERFLOW_IRQ_ENABLE ,Enables packet buffer overflow IRQ " "Disabled,Enabled" textline " " bitfld.long 0x00 17.--18. " WR_ENDIAN ,Specifies write endian of packet buffer" "Little endian,Big endian,Half word swap,Half word big endian" bitfld.long 0x00 16. " IN_CLK_ENABLE ,Enables the input clock" "Disabled,Enabled" bitfld.long 0x00 12. " AUTO_SYNC ,Enable automatic synchronization (AutoSync) on Sync Byte" "Disabled,Enabled" textline " " bitfld.long 0x00 8. " PACKET_START ,Polarity of the signal PACKET_START" "High active,Low active" bitfld.long 0x00 7. " TS_EN ,Polarity of TS_EN" "High active,Low active" bitfld.long 0x00 4. " TS_CLK ,Invert TS_CLK" "Not inverted,Inverted" textline " " bitfld.long 0x00 0.--1. " SERIAL_PARALLEL ,Specifies the serial and parallel mode (TPS = TS_PACKET_START)" ",Serial with TSP,Parallel no TSP,Parallel with TPS" group.long 0x24014++0x03 line.long 0x00 "TSD3_INPUT_CFG,Input configuration" hexmask.long.byte 0x00 24.--31. 1. " SYNC_BYTE_DISTANCE ,Distance between Sync Bytes" bitfld.long 0x00 20.--21. " INPUT_SELECT ,Select the input channel" "A,B,C,C" bitfld.long 0x00 19. " PACKET_BUF_OVERFLOW_IRQ_ENABLE ,Enables packet buffer overflow IRQ " "Disabled,Enabled" textline " " bitfld.long 0x00 17.--18. " WR_ENDIAN ,Specifies write endian of packet buffer" "Little endian,Big endian,Half word swap,Half word big endian" bitfld.long 0x00 16. " IN_CLK_ENABLE ,Enables the input clock" "Disabled,Enabled" bitfld.long 0x00 12. " AUTO_SYNC ,Enable automatic synchronization (AutoSync) on Sync Byte" "Disabled,Enabled" textline " " bitfld.long 0x00 8. " PACKET_START ,Polarity of the signal PACKET_START" "High active,Low active" bitfld.long 0x00 7. " TS_EN ,Polarity of TS_EN" "High active,Low active" bitfld.long 0x00 4. " TS_CLK ,Invert TS_CLK" "Not inverted,Inverted" textline " " bitfld.long 0x00 0.--1. " SERIAL_PARALLEL ,Specifies the serial and parallel mode (TPS = TS_PACKET_START)" ",Serial with TSP,Parallel no TSP,Parallel with TPS" group.long 0x42408C++0x03 line.long 0x00 "TSD_ENABLE_INPUT_CLK,TSD_ENABLE_INPUT_CLK" bitfld.long 0x00 3. " VALUE3 ,Enables the input clock of TSD 3" "Disabled,Enabled" bitfld.long 0x00 2. " VALUE2 ,Enables the input clock of TSD 2" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " VALUE1 ,Enables the input clock of TSD 1" "Disabled,Enabled" bitfld.long 0x00 0. " VALUE0 ,Enables the input clock of TSD 0" "Disabled,Enabled" rgroup.long 0x424084++0x07 line.long 0x00 "TSD_INPUT_CHANNEL_AB_DATA,These registers can be used to debug input channel settings" bitfld.long 0x00 26. " TS1CLK ,Input clock of input channel B" "0,1" bitfld.long 0x00 25. " TS1EN ,TS_EN of input channel B" "0,1" textline " " bitfld.long 0x00 24. " TS1START ,TS_START of input channel B" "0,1" hexmask.long.byte 0x00 16.--23. 1. " TS1DATA ,TS_DATA of input channel B" textline " " bitfld.long 0x00 14.--15. " INPUTSELECT1 ,Input channel selection of TSD1 (configured in INPUT_CFG)" "0,1,2,3" bitfld.long 0x00 12.--13. " INPUTSELECT0 ,Input channel selection of TSD0 (configured in INPUT_CFG)" "0,1,2,3" textline " " bitfld.long 0x00 10. " TS0CLK ,Input clock of input channel A" "0,1" bitfld.long 0x00 9. " TS0EN ,TS_EN of input channel A" "0,1" textline " " bitfld.long 0x00 8. " TS0START ,TS_START of input channel A" "0,1" hexmask.long.byte 0x00 0.--7. 1. " TS0DATA ,TS_DATA of input channel A" line.long 0x04 "TSD_INPUT_CHANNEL_BC_DATA,Hardware debug register" tree "Direct Write Mode" tree "TSD1" tree "Packet 0" wgroup.long 0x20004++0x03 line.long 0x00 "TSD1_PACKET0_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x20008++0x03 line.long 0x00 "TSD1_PACKET0_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x2000C++0x03 line.long 0x00 "TSD1_PACKET0_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x20010++0x03 line.long 0x00 "TSD1_PACKET0_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x20014++0x03 line.long 0x00 "TSD1_PACKET0_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x20018++0x03 line.long 0x00 "TSD1_PACKET0_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x2001C++0x03 line.long 0x00 "TSD1_PACKET0_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x20020++0x03 line.long 0x00 "TSD1_PACKET0_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x20024++0x03 line.long 0x00 "TSD1_PACKET0_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x20028++0x03 line.long 0x00 "TSD1_PACKET0_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x2002C++0x03 line.long 0x00 "TSD1_PACKET0_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x20030++0x03 line.long 0x00 "TSD1_PACKET0_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x20034++0x03 line.long 0x00 "TSD1_PACKET0_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x20038++0x03 line.long 0x00 "TSD1_PACKET0_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x2003C++0x03 line.long 0x00 "TSD1_PACKET0_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x20040++0x03 line.long 0x00 "TSD1_PACKET0_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x20044++0x03 line.long 0x00 "TSD1_PACKET0_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x20048++0x03 line.long 0x00 "TSD1_PACKET0_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x2004C++0x03 line.long 0x00 "TSD1_PACKET0_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x20050++0x03 line.long 0x00 "TSD1_PACKET0_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x20054++0x03 line.long 0x00 "TSD1_PACKET0_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x20058++0x03 line.long 0x00 "TSD1_PACKET0_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x2005C++0x03 line.long 0x00 "TSD1_PACKET0_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x20060++0x03 line.long 0x00 "TSD1_PACKET0_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x20064++0x03 line.long 0x00 "TSD1_PACKET0_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x20068++0x03 line.long 0x00 "TSD1_PACKET0_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x2006C++0x03 line.long 0x00 "TSD1_PACKET0_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x20070++0x03 line.long 0x00 "TSD1_PACKET0_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x20074++0x03 line.long 0x00 "TSD1_PACKET0_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x20078++0x03 line.long 0x00 "TSD1_PACKET0_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x2007C++0x03 line.long 0x00 "TSD1_PACKET0_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x20080++0x03 line.long 0x00 "TSD1_PACKET0_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x20084++0x03 line.long 0x00 "TSD1_PACKET0_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x20088++0x03 line.long 0x00 "TSD1_PACKET0_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x2008C++0x03 line.long 0x00 "TSD1_PACKET0_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x20090++0x03 line.long 0x00 "TSD1_PACKET0_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x20094++0x03 line.long 0x00 "TSD1_PACKET0_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x20098++0x03 line.long 0x00 "TSD1_PACKET0_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x2009C++0x03 line.long 0x00 "TSD1_PACKET0_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x200A0++0x03 line.long 0x00 "TSD1_PACKET0_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x200A4++0x03 line.long 0x00 "TSD1_PACKET0_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x200A8++0x03 line.long 0x00 "TSD1_PACKET0_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x200AC++0x03 line.long 0x00 "TSD1_PACKET0_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x200B0++0x03 line.long 0x00 "TSD1_PACKET0_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x200B4++0x03 line.long 0x00 "TSD1_PACKET0_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x200B8++0x03 line.long 0x00 "TSD1_PACKET0_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x200BC++0x03 line.long 0x00 "TSD1_PACKET0_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 1" wgroup.long 0x200C4++0x03 line.long 0x00 "TSD1_PACKET1_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x200C8++0x03 line.long 0x00 "TSD1_PACKET1_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x200CC++0x03 line.long 0x00 "TSD1_PACKET1_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x200D0++0x03 line.long 0x00 "TSD1_PACKET1_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x200D4++0x03 line.long 0x00 "TSD1_PACKET1_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x200D8++0x03 line.long 0x00 "TSD1_PACKET1_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x200DC++0x03 line.long 0x00 "TSD1_PACKET1_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x200E0++0x03 line.long 0x00 "TSD1_PACKET1_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x200E4++0x03 line.long 0x00 "TSD1_PACKET1_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x200E8++0x03 line.long 0x00 "TSD1_PACKET1_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x200EC++0x03 line.long 0x00 "TSD1_PACKET1_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x200F0++0x03 line.long 0x00 "TSD1_PACKET1_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x200F4++0x03 line.long 0x00 "TSD1_PACKET1_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x200F8++0x03 line.long 0x00 "TSD1_PACKET1_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x200FC++0x03 line.long 0x00 "TSD1_PACKET1_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x20100++0x03 line.long 0x00 "TSD1_PACKET1_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x20104++0x03 line.long 0x00 "TSD1_PACKET1_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x20108++0x03 line.long 0x00 "TSD1_PACKET1_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x2010C++0x03 line.long 0x00 "TSD1_PACKET1_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x20110++0x03 line.long 0x00 "TSD1_PACKET1_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x20114++0x03 line.long 0x00 "TSD1_PACKET1_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x20118++0x03 line.long 0x00 "TSD1_PACKET1_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x2011C++0x03 line.long 0x00 "TSD1_PACKET1_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x20120++0x03 line.long 0x00 "TSD1_PACKET1_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x20124++0x03 line.long 0x00 "TSD1_PACKET1_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x20128++0x03 line.long 0x00 "TSD1_PACKET1_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x2012C++0x03 line.long 0x00 "TSD1_PACKET1_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x20130++0x03 line.long 0x00 "TSD1_PACKET1_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x20134++0x03 line.long 0x00 "TSD1_PACKET1_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x20138++0x03 line.long 0x00 "TSD1_PACKET1_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x2013C++0x03 line.long 0x00 "TSD1_PACKET1_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x20140++0x03 line.long 0x00 "TSD1_PACKET1_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x20144++0x03 line.long 0x00 "TSD1_PACKET1_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x20148++0x03 line.long 0x00 "TSD1_PACKET1_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x2014C++0x03 line.long 0x00 "TSD1_PACKET1_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x20150++0x03 line.long 0x00 "TSD1_PACKET1_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x20154++0x03 line.long 0x00 "TSD1_PACKET1_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x20158++0x03 line.long 0x00 "TSD1_PACKET1_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x2015C++0x03 line.long 0x00 "TSD1_PACKET1_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x20160++0x03 line.long 0x00 "TSD1_PACKET1_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x20164++0x03 line.long 0x00 "TSD1_PACKET1_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x20168++0x03 line.long 0x00 "TSD1_PACKET1_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x2016C++0x03 line.long 0x00 "TSD1_PACKET1_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x20170++0x03 line.long 0x00 "TSD1_PACKET1_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x20174++0x03 line.long 0x00 "TSD1_PACKET1_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x20178++0x03 line.long 0x00 "TSD1_PACKET1_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x2017C++0x03 line.long 0x00 "TSD1_PACKET1_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 2" wgroup.long 0x20184++0x03 line.long 0x00 "TSD1_PACKET2_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x20188++0x03 line.long 0x00 "TSD1_PACKET2_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x2018C++0x03 line.long 0x00 "TSD1_PACKET2_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x20190++0x03 line.long 0x00 "TSD1_PACKET2_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x20194++0x03 line.long 0x00 "TSD1_PACKET2_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x20198++0x03 line.long 0x00 "TSD1_PACKET2_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x2019C++0x03 line.long 0x00 "TSD1_PACKET2_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x201A0++0x03 line.long 0x00 "TSD1_PACKET2_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x201A4++0x03 line.long 0x00 "TSD1_PACKET2_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x201A8++0x03 line.long 0x00 "TSD1_PACKET2_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x201AC++0x03 line.long 0x00 "TSD1_PACKET2_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x201B0++0x03 line.long 0x00 "TSD1_PACKET2_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x201B4++0x03 line.long 0x00 "TSD1_PACKET2_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x201B8++0x03 line.long 0x00 "TSD1_PACKET2_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x201BC++0x03 line.long 0x00 "TSD1_PACKET2_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x201C0++0x03 line.long 0x00 "TSD1_PACKET2_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x201C4++0x03 line.long 0x00 "TSD1_PACKET2_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x201C8++0x03 line.long 0x00 "TSD1_PACKET2_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x201CC++0x03 line.long 0x00 "TSD1_PACKET2_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x201D0++0x03 line.long 0x00 "TSD1_PACKET2_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x201D4++0x03 line.long 0x00 "TSD1_PACKET2_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x201D8++0x03 line.long 0x00 "TSD1_PACKET2_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x201DC++0x03 line.long 0x00 "TSD1_PACKET2_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x201E0++0x03 line.long 0x00 "TSD1_PACKET2_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x201E4++0x03 line.long 0x00 "TSD1_PACKET2_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x201E8++0x03 line.long 0x00 "TSD1_PACKET2_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x201EC++0x03 line.long 0x00 "TSD1_PACKET2_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x201F0++0x03 line.long 0x00 "TSD1_PACKET2_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x201F4++0x03 line.long 0x00 "TSD1_PACKET2_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x201F8++0x03 line.long 0x00 "TSD1_PACKET2_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x201FC++0x03 line.long 0x00 "TSD1_PACKET2_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x20200++0x03 line.long 0x00 "TSD1_PACKET2_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x20204++0x03 line.long 0x00 "TSD1_PACKET2_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x20208++0x03 line.long 0x00 "TSD1_PACKET2_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x2020C++0x03 line.long 0x00 "TSD1_PACKET2_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x20210++0x03 line.long 0x00 "TSD1_PACKET2_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x20214++0x03 line.long 0x00 "TSD1_PACKET2_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x20218++0x03 line.long 0x00 "TSD1_PACKET2_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x2021C++0x03 line.long 0x00 "TSD1_PACKET2_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x20220++0x03 line.long 0x00 "TSD1_PACKET2_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x20224++0x03 line.long 0x00 "TSD1_PACKET2_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x20228++0x03 line.long 0x00 "TSD1_PACKET2_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x2022C++0x03 line.long 0x00 "TSD1_PACKET2_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x20230++0x03 line.long 0x00 "TSD1_PACKET2_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x20234++0x03 line.long 0x00 "TSD1_PACKET2_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x20238++0x03 line.long 0x00 "TSD1_PACKET2_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x2023C++0x03 line.long 0x00 "TSD1_PACKET2_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 3" wgroup.long 0x20244++0x03 line.long 0x00 "TSD1_PACKET3_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x20248++0x03 line.long 0x00 "TSD1_PACKET3_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x2024C++0x03 line.long 0x00 "TSD1_PACKET3_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x20250++0x03 line.long 0x00 "TSD1_PACKET3_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x20254++0x03 line.long 0x00 "TSD1_PACKET3_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x20258++0x03 line.long 0x00 "TSD1_PACKET3_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x2025C++0x03 line.long 0x00 "TSD1_PACKET3_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x20260++0x03 line.long 0x00 "TSD1_PACKET3_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x20264++0x03 line.long 0x00 "TSD1_PACKET3_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x20268++0x03 line.long 0x00 "TSD1_PACKET3_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x2026C++0x03 line.long 0x00 "TSD1_PACKET3_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x20270++0x03 line.long 0x00 "TSD1_PACKET3_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x20274++0x03 line.long 0x00 "TSD1_PACKET3_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x20278++0x03 line.long 0x00 "TSD1_PACKET3_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x2027C++0x03 line.long 0x00 "TSD1_PACKET3_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x20280++0x03 line.long 0x00 "TSD1_PACKET3_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x20284++0x03 line.long 0x00 "TSD1_PACKET3_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x20288++0x03 line.long 0x00 "TSD1_PACKET3_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x2028C++0x03 line.long 0x00 "TSD1_PACKET3_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x20290++0x03 line.long 0x00 "TSD1_PACKET3_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x20294++0x03 line.long 0x00 "TSD1_PACKET3_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x20298++0x03 line.long 0x00 "TSD1_PACKET3_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x2029C++0x03 line.long 0x00 "TSD1_PACKET3_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x202A0++0x03 line.long 0x00 "TSD1_PACKET3_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x202A4++0x03 line.long 0x00 "TSD1_PACKET3_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x202A8++0x03 line.long 0x00 "TSD1_PACKET3_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x202AC++0x03 line.long 0x00 "TSD1_PACKET3_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x202B0++0x03 line.long 0x00 "TSD1_PACKET3_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x202B4++0x03 line.long 0x00 "TSD1_PACKET3_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x202B8++0x03 line.long 0x00 "TSD1_PACKET3_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x202BC++0x03 line.long 0x00 "TSD1_PACKET3_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x202C0++0x03 line.long 0x00 "TSD1_PACKET3_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x202C4++0x03 line.long 0x00 "TSD1_PACKET3_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x202C8++0x03 line.long 0x00 "TSD1_PACKET3_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x202CC++0x03 line.long 0x00 "TSD1_PACKET3_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x202D0++0x03 line.long 0x00 "TSD1_PACKET3_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x202D4++0x03 line.long 0x00 "TSD1_PACKET3_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x202D8++0x03 line.long 0x00 "TSD1_PACKET3_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x202DC++0x03 line.long 0x00 "TSD1_PACKET3_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x202E0++0x03 line.long 0x00 "TSD1_PACKET3_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x202E4++0x03 line.long 0x00 "TSD1_PACKET3_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x202E8++0x03 line.long 0x00 "TSD1_PACKET3_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x202EC++0x03 line.long 0x00 "TSD1_PACKET3_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x202F0++0x03 line.long 0x00 "TSD1_PACKET3_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x202F4++0x03 line.long 0x00 "TSD1_PACKET3_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x202F8++0x03 line.long 0x00 "TSD1_PACKET3_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x202FC++0x03 line.long 0x00 "TSD1_PACKET3_46,46 word (4 bytes) in a transport stream packet" tree.end textline " " group.long 0x24000++0x03 line.long 0x00 "TSD1_PACKET_CTRL,Indicates if the packet in a buffer is valid" bitfld.long 0x00 12.--14. " PACKET_BUF_VALID_3 ,Indicates if the packet in PACKET_BUFFER_3 is valid" "b'000,b'001,b'010,b'011,b'100,b'101,b'110,b'111" bitfld.long 0x00 8.--10. " PACKET_BUF_VALID_2 ,Indicates if the packet in PACKET_BUFFER_2 is valid" "b'000,b'001,b'010,b'011,b'100,b'101,b'110,b'111" bitfld.long 0x00 4.--6. " PACKET_BUF_VALID_1 ,Indicates if the packet in PACKET_BUFFER_1 is valid" "b'000,b'001,b'010,b'011,b'100,b'101,b'110,b'111" textline " " bitfld.long 0x00 0.--2. " PACKET_BUF_VALID_0 ,Indicates if the packet in PACKET_BUFFER_0 is valid" "b'000,b'001,b'010,b'011,b'100,b'101,b'110,b'111" tree.end tree "TDS2" tree "Packet 0" wgroup.long 0x120004++0x03 line.long 0x00 "TSD2_PACKET0_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x120008++0x03 line.long 0x00 "TSD2_PACKET0_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x12000C++0x03 line.long 0x00 "TSD2_PACKET0_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x120010++0x03 line.long 0x00 "TSD2_PACKET0_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x120014++0x03 line.long 0x00 "TSD2_PACKET0_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x120018++0x03 line.long 0x00 "TSD2_PACKET0_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x12001C++0x03 line.long 0x00 "TSD2_PACKET0_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x120020++0x03 line.long 0x00 "TSD2_PACKET0_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x120024++0x03 line.long 0x00 "TSD2_PACKET0_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x120028++0x03 line.long 0x00 "TSD2_PACKET0_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x12002C++0x03 line.long 0x00 "TSD2_PACKET0_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x120030++0x03 line.long 0x00 "TSD2_PACKET0_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x120034++0x03 line.long 0x00 "TSD2_PACKET0_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x120038++0x03 line.long 0x00 "TSD2_PACKET0_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x12003C++0x03 line.long 0x00 "TSD2_PACKET0_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x120040++0x03 line.long 0x00 "TSD2_PACKET0_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x120044++0x03 line.long 0x00 "TSD2_PACKET0_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x120048++0x03 line.long 0x00 "TSD2_PACKET0_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x12004C++0x03 line.long 0x00 "TSD2_PACKET0_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x120050++0x03 line.long 0x00 "TSD2_PACKET0_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x120054++0x03 line.long 0x00 "TSD2_PACKET0_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x120058++0x03 line.long 0x00 "TSD2_PACKET0_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x12005C++0x03 line.long 0x00 "TSD2_PACKET0_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x120060++0x03 line.long 0x00 "TSD2_PACKET0_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x120064++0x03 line.long 0x00 "TSD2_PACKET0_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x120068++0x03 line.long 0x00 "TSD2_PACKET0_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x12006C++0x03 line.long 0x00 "TSD2_PACKET0_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x120070++0x03 line.long 0x00 "TSD2_PACKET0_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x120074++0x03 line.long 0x00 "TSD2_PACKET0_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x120078++0x03 line.long 0x00 "TSD2_PACKET0_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x12007C++0x03 line.long 0x00 "TSD2_PACKET0_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x120080++0x03 line.long 0x00 "TSD2_PACKET0_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x120084++0x03 line.long 0x00 "TSD2_PACKET0_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x120088++0x03 line.long 0x00 "TSD2_PACKET0_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x12008C++0x03 line.long 0x00 "TSD2_PACKET0_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x120090++0x03 line.long 0x00 "TSD2_PACKET0_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x120094++0x03 line.long 0x00 "TSD2_PACKET0_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x120098++0x03 line.long 0x00 "TSD2_PACKET0_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x12009C++0x03 line.long 0x00 "TSD2_PACKET0_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x1200A0++0x03 line.long 0x00 "TSD2_PACKET0_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x1200A4++0x03 line.long 0x00 "TSD2_PACKET0_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x1200A8++0x03 line.long 0x00 "TSD2_PACKET0_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x1200AC++0x03 line.long 0x00 "TSD2_PACKET0_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x1200B0++0x03 line.long 0x00 "TSD2_PACKET0_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x1200B4++0x03 line.long 0x00 "TSD2_PACKET0_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x1200B8++0x03 line.long 0x00 "TSD2_PACKET0_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x1200BC++0x03 line.long 0x00 "TSD2_PACKET0_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 1" wgroup.long 0x1200C4++0x03 line.long 0x00 "TSD2_PACKET1_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x1200C8++0x03 line.long 0x00 "TSD2_PACKET1_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x1200CC++0x03 line.long 0x00 "TSD2_PACKET1_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x1200D0++0x03 line.long 0x00 "TSD2_PACKET1_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x1200D4++0x03 line.long 0x00 "TSD2_PACKET1_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x1200D8++0x03 line.long 0x00 "TSD2_PACKET1_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x1200DC++0x03 line.long 0x00 "TSD2_PACKET1_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x1200E0++0x03 line.long 0x00 "TSD2_PACKET1_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x1200E4++0x03 line.long 0x00 "TSD2_PACKET1_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x1200E8++0x03 line.long 0x00 "TSD2_PACKET1_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x1200EC++0x03 line.long 0x00 "TSD2_PACKET1_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x1200F0++0x03 line.long 0x00 "TSD2_PACKET1_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x1200F4++0x03 line.long 0x00 "TSD2_PACKET1_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x1200F8++0x03 line.long 0x00 "TSD2_PACKET1_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x1200FC++0x03 line.long 0x00 "TSD2_PACKET1_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x120100++0x03 line.long 0x00 "TSD2_PACKET1_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x120104++0x03 line.long 0x00 "TSD2_PACKET1_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x120108++0x03 line.long 0x00 "TSD2_PACKET1_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x12010C++0x03 line.long 0x00 "TSD2_PACKET1_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x120110++0x03 line.long 0x00 "TSD2_PACKET1_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x120114++0x03 line.long 0x00 "TSD2_PACKET1_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x120118++0x03 line.long 0x00 "TSD2_PACKET1_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x12011C++0x03 line.long 0x00 "TSD2_PACKET1_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x120120++0x03 line.long 0x00 "TSD2_PACKET1_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x120124++0x03 line.long 0x00 "TSD2_PACKET1_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x120128++0x03 line.long 0x00 "TSD2_PACKET1_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x12012C++0x03 line.long 0x00 "TSD2_PACKET1_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x120130++0x03 line.long 0x00 "TSD2_PACKET1_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x120134++0x03 line.long 0x00 "TSD2_PACKET1_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x120138++0x03 line.long 0x00 "TSD2_PACKET1_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x12013C++0x03 line.long 0x00 "TSD2_PACKET1_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x120140++0x03 line.long 0x00 "TSD2_PACKET1_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x120144++0x03 line.long 0x00 "TSD2_PACKET1_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x120148++0x03 line.long 0x00 "TSD2_PACKET1_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x12014C++0x03 line.long 0x00 "TSD2_PACKET1_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x120150++0x03 line.long 0x00 "TSD2_PACKET1_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x120154++0x03 line.long 0x00 "TSD2_PACKET1_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x120158++0x03 line.long 0x00 "TSD2_PACKET1_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x12015C++0x03 line.long 0x00 "TSD2_PACKET1_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x120160++0x03 line.long 0x00 "TSD2_PACKET1_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x120164++0x03 line.long 0x00 "TSD2_PACKET1_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x120168++0x03 line.long 0x00 "TSD2_PACKET1_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x12016C++0x03 line.long 0x00 "TSD2_PACKET1_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x120170++0x03 line.long 0x00 "TSD2_PACKET1_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x120174++0x03 line.long 0x00 "TSD2_PACKET1_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x120178++0x03 line.long 0x00 "TSD2_PACKET1_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x12017C++0x03 line.long 0x00 "TSD2_PACKET1_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 2" wgroup.long 0x120184++0x03 line.long 0x00 "TSD2_PACKET2_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x120188++0x03 line.long 0x00 "TSD2_PACKET2_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x12018C++0x03 line.long 0x00 "TSD2_PACKET2_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x120190++0x03 line.long 0x00 "TSD2_PACKET2_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x120194++0x03 line.long 0x00 "TSD2_PACKET2_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x120198++0x03 line.long 0x00 "TSD2_PACKET2_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x12019C++0x03 line.long 0x00 "TSD2_PACKET2_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x1201A0++0x03 line.long 0x00 "TSD2_PACKET2_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x1201A4++0x03 line.long 0x00 "TSD2_PACKET2_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x1201A8++0x03 line.long 0x00 "TSD2_PACKET2_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x1201AC++0x03 line.long 0x00 "TSD2_PACKET2_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x1201B0++0x03 line.long 0x00 "TSD2_PACKET2_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x1201B4++0x03 line.long 0x00 "TSD2_PACKET2_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x1201B8++0x03 line.long 0x00 "TSD2_PACKET2_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x1201BC++0x03 line.long 0x00 "TSD2_PACKET2_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x1201C0++0x03 line.long 0x00 "TSD2_PACKET2_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x1201C4++0x03 line.long 0x00 "TSD2_PACKET2_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x1201C8++0x03 line.long 0x00 "TSD2_PACKET2_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x1201CC++0x03 line.long 0x00 "TSD2_PACKET2_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x1201D0++0x03 line.long 0x00 "TSD2_PACKET2_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x1201D4++0x03 line.long 0x00 "TSD2_PACKET2_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x1201D8++0x03 line.long 0x00 "TSD2_PACKET2_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x1201DC++0x03 line.long 0x00 "TSD2_PACKET2_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x1201E0++0x03 line.long 0x00 "TSD2_PACKET2_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x1201E4++0x03 line.long 0x00 "TSD2_PACKET2_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x1201E8++0x03 line.long 0x00 "TSD2_PACKET2_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x1201EC++0x03 line.long 0x00 "TSD2_PACKET2_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x1201F0++0x03 line.long 0x00 "TSD2_PACKET2_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x1201F4++0x03 line.long 0x00 "TSD2_PACKET2_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x1201F8++0x03 line.long 0x00 "TSD2_PACKET2_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x1201FC++0x03 line.long 0x00 "TSD2_PACKET2_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x120200++0x03 line.long 0x00 "TSD2_PACKET2_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x120204++0x03 line.long 0x00 "TSD2_PACKET2_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x120208++0x03 line.long 0x00 "TSD2_PACKET2_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x12020C++0x03 line.long 0x00 "TSD2_PACKET2_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x120210++0x03 line.long 0x00 "TSD2_PACKET2_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x120214++0x03 line.long 0x00 "TSD2_PACKET2_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x120218++0x03 line.long 0x00 "TSD2_PACKET2_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x12021C++0x03 line.long 0x00 "TSD2_PACKET2_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x120220++0x03 line.long 0x00 "TSD2_PACKET2_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x120224++0x03 line.long 0x00 "TSD2_PACKET2_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x120228++0x03 line.long 0x00 "TSD2_PACKET2_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x12022C++0x03 line.long 0x00 "TSD2_PACKET2_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x120230++0x03 line.long 0x00 "TSD2_PACKET2_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x120234++0x03 line.long 0x00 "TSD2_PACKET2_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x120238++0x03 line.long 0x00 "TSD2_PACKET2_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x12023C++0x03 line.long 0x00 "TSD2_PACKET2_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 3" wgroup.long 0x120244++0x03 line.long 0x00 "TSD2_PACKET3_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x120248++0x03 line.long 0x00 "TSD2_PACKET3_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x12024C++0x03 line.long 0x00 "TSD2_PACKET3_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x120250++0x03 line.long 0x00 "TSD2_PACKET3_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x120254++0x03 line.long 0x00 "TSD2_PACKET3_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x120258++0x03 line.long 0x00 "TSD2_PACKET3_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x12025C++0x03 line.long 0x00 "TSD2_PACKET3_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x120260++0x03 line.long 0x00 "TSD2_PACKET3_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x120264++0x03 line.long 0x00 "TSD2_PACKET3_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x120268++0x03 line.long 0x00 "TSD2_PACKET3_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x12026C++0x03 line.long 0x00 "TSD2_PACKET3_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x120270++0x03 line.long 0x00 "TSD2_PACKET3_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x120274++0x03 line.long 0x00 "TSD2_PACKET3_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x120278++0x03 line.long 0x00 "TSD2_PACKET3_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x12027C++0x03 line.long 0x00 "TSD2_PACKET3_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x120280++0x03 line.long 0x00 "TSD2_PACKET3_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x120284++0x03 line.long 0x00 "TSD2_PACKET3_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x120288++0x03 line.long 0x00 "TSD2_PACKET3_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x12028C++0x03 line.long 0x00 "TSD2_PACKET3_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x120290++0x03 line.long 0x00 "TSD2_PACKET3_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x120294++0x03 line.long 0x00 "TSD2_PACKET3_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x120298++0x03 line.long 0x00 "TSD2_PACKET3_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x12029C++0x03 line.long 0x00 "TSD2_PACKET3_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x1202A0++0x03 line.long 0x00 "TSD2_PACKET3_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x1202A4++0x03 line.long 0x00 "TSD2_PACKET3_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x1202A8++0x03 line.long 0x00 "TSD2_PACKET3_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x1202AC++0x03 line.long 0x00 "TSD2_PACKET3_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x1202B0++0x03 line.long 0x00 "TSD2_PACKET3_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x1202B4++0x03 line.long 0x00 "TSD2_PACKET3_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x1202B8++0x03 line.long 0x00 "TSD2_PACKET3_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x1202BC++0x03 line.long 0x00 "TSD2_PACKET3_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x1202C0++0x03 line.long 0x00 "TSD2_PACKET3_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x1202C4++0x03 line.long 0x00 "TSD2_PACKET3_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x1202C8++0x03 line.long 0x00 "TSD2_PACKET3_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x1202CC++0x03 line.long 0x00 "TSD2_PACKET3_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x1202D0++0x03 line.long 0x00 "TSD2_PACKET3_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x1202D4++0x03 line.long 0x00 "TSD2_PACKET3_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x1202D8++0x03 line.long 0x00 "TSD2_PACKET3_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x1202DC++0x03 line.long 0x00 "TSD2_PACKET3_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x1202E0++0x03 line.long 0x00 "TSD2_PACKET3_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x1202E4++0x03 line.long 0x00 "TSD2_PACKET3_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x1202E8++0x03 line.long 0x00 "TSD2_PACKET3_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x1202EC++0x03 line.long 0x00 "TSD2_PACKET3_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x1202F0++0x03 line.long 0x00 "TSD2_PACKET3_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x1202F4++0x03 line.long 0x00 "TSD2_PACKET3_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x1202F8++0x03 line.long 0x00 "TSD2_PACKET3_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x1202FC++0x03 line.long 0x00 "TSD2_PACKET3_46,46 word (4 bytes) in a transport stream packet" tree.end textline " " group.long 0x124000++0x03 line.long 0x00 "TSD2_PACKET_CTRL,Indicates if the packet in a buffer is valid" bitfld.long 0x00 12.--14. " PACKET_BUF_VALID_3 ,Indicates if the packet in PACKET_BUFFER_3 is valid" "b'000,b'001,b'010,b'011,b'100,b'101,b'110,b'111" bitfld.long 0x00 8.--10. " PACKET_BUF_VALID_2 ,Indicates if the packet in PACKET_BUFFER_2 is valid" "b'000,b'001,b'010,b'011,b'100,b'101,b'110,b'111" bitfld.long 0x00 4.--6. " PACKET_BUF_VALID_1 ,Indicates if the packet in PACKET_BUFFER_1 is valid" "b'000,b'001,b'010,b'011,b'100,b'101,b'110,b'111" textline " " bitfld.long 0x00 0.--2. " PACKET_BUF_VALID_0 ,Indicates if the packet in PACKET_BUFFER_0 is valid" "b'000,b'001,b'010,b'011,b'100,b'101,b'110,b'111" tree.end tree.end tree "Linear Write Mode" tree "TDS1" tree "Packet 0" wgroup.long 0x21000++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x21004++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x21008++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x2100C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x21010++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x21014++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x21018++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x2101C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x21020++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x21024++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x21028++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x2102C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x21030++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x21034++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x21038++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x2103C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x21040++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x21044++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x21048++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x2104C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x21050++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x21054++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x21058++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x2105C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x21060++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x21064++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x21068++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x2106C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x21070++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x21074++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x21078++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x2107C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x21080++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x21084++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x21088++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x2108C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x21090++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x21094++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x21098++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x2109C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x210A0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x210A4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x210A8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x210AC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x210B0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x210B4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x210B8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET0_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 1" wgroup.long 0x210BC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x210C0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x210C4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x210C8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x210CC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x210D0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x210D4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x210D8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x210DC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x210E0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x210E4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x210E8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x210EC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x210F0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x210F4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x210F8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x210FC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x21100++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x21104++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x21108++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x2110C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x21110++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x21114++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x21118++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x2111C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x21120++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x21124++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x21128++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x2112C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x21130++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x21134++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x21138++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x2113C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x21140++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x21144++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x21148++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x2114C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x21150++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x21154++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x21158++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x2115C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x21160++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x21164++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x21168++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x2116C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x21170++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x21174++0x03 line.long 0x00 "TSD1_LINEAR_PACKET1_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 2" wgroup.long 0x21178++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x2117C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x21180++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x21184++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x21188++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x2118C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x21190++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x21194++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x21198++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x2119C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x211A0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x211A4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x211A8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x211AC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x211B0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x211B4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x211B8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x211BC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x211C0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x211C4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x211C8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x211CC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x211D0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x211D4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x211D8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x211DC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x211E0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x211E4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x211E8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x211EC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x211F0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x211F4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x211F8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x211FC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x21200++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x21204++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x21208++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x2120C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x21210++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x21214++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x21218++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x2121C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x21220++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x21224++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x21228++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x2122C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x21230++0x03 line.long 0x00 "TSD1_LINEAR_PACKET2_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 3" wgroup.long 0x21234++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x21238++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x2123C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x21240++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x21244++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x21248++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x2124C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x21250++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x21254++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x21258++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x2125C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x21260++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x21264++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x21268++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x2126C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x21270++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x21274++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x21278++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x2127C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x21280++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x21284++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x21288++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x2128C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x21290++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x21294++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x21298++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x2129C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x212A0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x212A4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x212A8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x212AC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x212B0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x212B4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x212B8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x212BC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x212C0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x212C4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x212C8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x212CC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x212D0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x212D4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x212D8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x212DC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x212E0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x212E4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x212E8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x212EC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET3_46,46 word (4 bytes) in a transport stream packet" tree.end tree.end tree "TDS2" tree "Packet 0" wgroup.long 0x121000++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x121004++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x121008++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x12100C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x121010++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x121014++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x121018++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x12101C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x121020++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x121024++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x121028++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x12102C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x121030++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x121034++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x121038++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x12103C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x121040++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x121044++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x121048++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x12104C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x121050++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x121054++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x121058++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x12105C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x121060++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x121064++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x121068++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x12106C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x121070++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x121074++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x121078++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x12107C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x121080++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x121084++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x121088++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x12108C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x121090++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x121094++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x121098++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x12109C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x1210A0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x1210A4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x1210A8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x1210AC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x1210B0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x1210B4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x1210B8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET0_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 1" wgroup.long 0x1210BC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x1210C0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x1210C4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x1210C8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x1210CC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x1210D0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x1210D4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x1210D8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x1210DC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x1210E0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x1210E4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x1210E8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x1210EC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x1210F0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x1210F4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x1210F8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x1210FC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x121100++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x121104++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x121108++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x12110C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x121110++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x121114++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x121118++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x12111C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x121120++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x121124++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x121128++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x12112C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x121130++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x121134++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x121138++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x12113C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x121140++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x121144++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x121148++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x12114C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x121150++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x121154++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x121158++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x12115C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x121160++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x121164++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x121168++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x12116C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x121170++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x121174++0x03 line.long 0x00 "TSD2_LINEAR_PACKET1_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 2" wgroup.long 0x121178++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x12117C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x121180++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x121184++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x121188++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x12118C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x121190++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x121194++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x121198++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x12119C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x1211A0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x1211A4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x1211A8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x1211AC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x1211B0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x1211B4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x1211B8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x1211BC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x1211C0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x1211C4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x1211C8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x1211CC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x1211D0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x1211D4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x1211D8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x1211DC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x1211E0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x1211E4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x1211E8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x1211EC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x1211F0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x1211F4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x1211F8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x1211FC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x121200++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x121204++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x121208++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x12120C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x121210++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x121214++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x121218++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x12121C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x121220++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x121224++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x121228++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x12122C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x121230++0x03 line.long 0x00 "TSD2_LINEAR_PACKET2_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 3" wgroup.long 0x121234++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x121238++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x12123C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x121240++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x121244++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x121248++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x12124C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x121250++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x121254++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x121258++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x12125C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x121260++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x121264++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x121268++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x12126C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x121270++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x121274++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x121278++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x12127C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x121280++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x121284++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x121288++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x12128C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x121290++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x121294++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x121298++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x12129C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x1212A0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x1212A4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x1212A8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x1212AC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x1212B0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x1212B4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x1212B8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x1212BC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x1212C0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x1212C4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x1212C8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x1212CC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x1212D0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x1212D4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x1212D8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x1212DC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x1212E0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x1212E4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x1212E8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x1212EC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET3_46,46 word (4 bytes) in a transport stream packet" tree.end tree.end tree.end tree "Linear Auto Packets" tree "TDS1" tree "Packet 0" wgroup.long 0x22000++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x22004++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x22008++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x2200C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x22010++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x22014++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x22018++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x2201C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x22020++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x22024++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x22028++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x2202C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x22030++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x22034++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x22038++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x2203C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x22040++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x22044++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x22048++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x2204C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x22050++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x22054++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x22058++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x2205C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x22060++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x22064++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x22068++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x2206C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x22070++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x22074++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x22078++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x2207C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x22080++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x22084++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x22088++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x2208C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x22090++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x22094++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x22098++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x2209C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x220A0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x220A4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x220A8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x220AC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x220B0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x220B4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x220B8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO0_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 1" wgroup.long 0x220BC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x220C0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x220C4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x220C8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x220CC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x220D0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x220D4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x220D8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x220DC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x220E0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x220E4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x220E8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x220EC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x220F0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x220F4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x220F8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x220FC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x22100++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x22104++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x22108++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x2210C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x22110++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x22114++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x22118++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x2211C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x22120++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x22124++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x22128++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x2212C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x22130++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x22134++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x22138++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x2213C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x22140++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x22144++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x22148++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x2214C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x22150++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x22154++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x22158++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x2215C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x22160++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x22164++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x22168++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x2216C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x22170++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x22174++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO1_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 2" wgroup.long 0x22178++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x2217C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x22180++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x22184++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x22188++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x2218C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x22190++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x22194++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x22198++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x2219C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x221A0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x221A4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x221A8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x221AC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x221B0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x221B4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x221B8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x221BC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x221C0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x221C4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x221C8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x221CC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x221D0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x221D4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x221D8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x221DC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x221E0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x221E4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x221E8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x221EC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x221F0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x221F4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x221F8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x221FC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x22200++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x22204++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x22208++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x2220C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x22210++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x22214++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x22218++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x2221C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x22220++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x22224++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x22228++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x2222C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x22230++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 3" wgroup.long 0x22234++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x22238++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x2223C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x22240++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x22244++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x22248++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x2224C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x22250++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x22254++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x22258++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x2225C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x22260++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x22264++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x22268++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x2226C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x22270++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x22274++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x22278++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x2227C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x22280++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x22284++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x22288++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x2228C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x22290++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x22294++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x22298++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x2229C++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x222A0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x222A4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x222A8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x222AC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x222B0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x222B4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x222B8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x222BC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x222C0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x222C4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x222C8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x222CC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x222D0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x222D4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x222D8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x222DC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x222E0++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x222E4++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x222E8++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x222EC++0x03 line.long 0x00 "TSD1_LINEAR_PACKET_AUTO3_46,46 word (4 bytes) in a transport stream packet" tree.end tree.end tree "TDS2" tree "Packet 0" wgroup.long 0x122000++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x122004++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x122008++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x12200C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x122010++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x122014++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x122018++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x12201C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x122020++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x122024++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x122028++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x12202C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x122030++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x122034++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x122038++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x12203C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x122040++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x122044++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x122048++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x12204C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x122050++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x122054++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x122058++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x12205C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x122060++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x122064++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x122068++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x12206C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x122070++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x122074++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x122078++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x12207C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x122080++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x122084++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x122088++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x12208C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x122090++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x122094++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x122098++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x12209C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x1220A0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x1220A4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x1220A8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x1220AC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x1220B0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x1220B4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x1220B8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO0_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 1" wgroup.long 0x1220BC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x1220C0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x1220C4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x1220C8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x1220CC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x1220D0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x1220D4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x1220D8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x1220DC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x1220E0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x1220E4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x1220E8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x1220EC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x1220F0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x1220F4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x1220F8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x1220FC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x122100++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x122104++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x122108++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x12210C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x122110++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x122114++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x122118++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x12211C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x122120++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x122124++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x122128++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x12212C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x122130++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x122134++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x122138++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x12213C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x122140++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x122144++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x122148++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x12214C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x122150++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x122154++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x122158++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x12215C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x122160++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x122164++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x122168++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x12216C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x122170++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x122174++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO1_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 2" wgroup.long 0x122178++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x12217C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x122180++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x122184++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x122188++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x12218C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x122190++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x122194++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x122198++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x12219C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x1221A0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x1221A4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x1221A8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x1221AC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x1221B0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x1221B4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x1221B8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x1221BC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x1221C0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x1221C4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x1221C8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x1221CC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x1221D0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x1221D4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x1221D8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x1221DC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x1221E0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x1221E4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x1221E8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x1221EC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x1221F0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x1221F4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x1221F8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x1221FC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x122200++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x122204++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x122208++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x12220C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x122210++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x122214++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x122218++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x12221C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x122220++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x122224++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x122228++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x12222C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x122230++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO2_46,46 word (4 bytes) in a transport stream packet" tree.end tree "Packet 3" wgroup.long 0x122234++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_0,0 word (4 bytes) in a transport stream packet" wgroup.long 0x122238++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_1,1 word (4 bytes) in a transport stream packet" wgroup.long 0x12223C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_2,2 word (4 bytes) in a transport stream packet" wgroup.long 0x122240++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_3,3 word (4 bytes) in a transport stream packet" wgroup.long 0x122244++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_4,4 word (4 bytes) in a transport stream packet" wgroup.long 0x122248++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_5,5 word (4 bytes) in a transport stream packet" wgroup.long 0x12224C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_6,6 word (4 bytes) in a transport stream packet" wgroup.long 0x122250++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_7,7 word (4 bytes) in a transport stream packet" wgroup.long 0x122254++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_8,8 word (4 bytes) in a transport stream packet" wgroup.long 0x122258++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_9,9 word (4 bytes) in a transport stream packet" wgroup.long 0x12225C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_10,10 word (4 bytes) in a transport stream packet" wgroup.long 0x122260++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_11,11 word (4 bytes) in a transport stream packet" wgroup.long 0x122264++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_12,12 word (4 bytes) in a transport stream packet" wgroup.long 0x122268++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_13,13 word (4 bytes) in a transport stream packet" wgroup.long 0x12226C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_14,14 word (4 bytes) in a transport stream packet" wgroup.long 0x122270++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_15,15 word (4 bytes) in a transport stream packet" wgroup.long 0x122274++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_16,16 word (4 bytes) in a transport stream packet" wgroup.long 0x122278++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_17,17 word (4 bytes) in a transport stream packet" wgroup.long 0x12227C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_18,18 word (4 bytes) in a transport stream packet" wgroup.long 0x122280++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_19,19 word (4 bytes) in a transport stream packet" wgroup.long 0x122284++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_20,20 word (4 bytes) in a transport stream packet" wgroup.long 0x122288++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_21,21 word (4 bytes) in a transport stream packet" wgroup.long 0x12228C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_22,22 word (4 bytes) in a transport stream packet" wgroup.long 0x122290++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_23,23 word (4 bytes) in a transport stream packet" wgroup.long 0x122294++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_24,24 word (4 bytes) in a transport stream packet" wgroup.long 0x122298++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_25,25 word (4 bytes) in a transport stream packet" wgroup.long 0x12229C++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_26,26 word (4 bytes) in a transport stream packet" wgroup.long 0x1222A0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_27,27 word (4 bytes) in a transport stream packet" wgroup.long 0x1222A4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_28,28 word (4 bytes) in a transport stream packet" wgroup.long 0x1222A8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_29,29 word (4 bytes) in a transport stream packet" wgroup.long 0x1222AC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_30,30 word (4 bytes) in a transport stream packet" wgroup.long 0x1222B0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_31,31 word (4 bytes) in a transport stream packet" wgroup.long 0x1222B4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_32,32 word (4 bytes) in a transport stream packet" wgroup.long 0x1222B8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_33,33 word (4 bytes) in a transport stream packet" wgroup.long 0x1222BC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_34,34 word (4 bytes) in a transport stream packet" wgroup.long 0x1222C0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_35,35 word (4 bytes) in a transport stream packet" wgroup.long 0x1222C4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_36,36 word (4 bytes) in a transport stream packet" wgroup.long 0x1222C8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_37,37 word (4 bytes) in a transport stream packet" wgroup.long 0x1222CC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_38,38 word (4 bytes) in a transport stream packet" wgroup.long 0x1222D0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_39,39 word (4 bytes) in a transport stream packet" wgroup.long 0x1222D4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_40,40 word (4 bytes) in a transport stream packet" wgroup.long 0x1222D8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_41,41 word (4 bytes) in a transport stream packet" wgroup.long 0x1222DC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_42,42 word (4 bytes) in a transport stream packet" wgroup.long 0x1222E0++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_43,43 word (4 bytes) in a transport stream packet" wgroup.long 0x1222E4++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_44,44 word (4 bytes) in a transport stream packet" wgroup.long 0x1222E8++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_45,45 word (4 bytes) in a transport stream packet" wgroup.long 0x1222EC++0x03 line.long 0x00 "TSD2_LINEAR_PACKET_AUTO3_46,46 word (4 bytes) in a transport stream packet" tree.end tree.end tree.end tree.end width 29. tree "PID Filter" tree "PID Values" tree "TSD1" wgroup.long 0x10000++0x03 line.long 0x00 "TSD1_PID_VALUE_0,PIDVALUE0" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10004++0x03 line.long 0x00 "TSD1_PID_VALUE_1,PIDVALUE1" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10008++0x03 line.long 0x00 "TSD1_PID_VALUE_2,PIDVALUE2" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x1000C++0x03 line.long 0x00 "TSD1_PID_VALUE_3,PIDVALUE3" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10010++0x03 line.long 0x00 "TSD1_PID_VALUE_4,PIDVALUE4" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10014++0x03 line.long 0x00 "TSD1_PID_VALUE_5,PIDVALUE5" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10018++0x03 line.long 0x00 "TSD1_PID_VALUE_6,PIDVALUE6" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x1001C++0x03 line.long 0x00 "TSD1_PID_VALUE_7,PIDVALUE7" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10020++0x03 line.long 0x00 "TSD1_PID_VALUE_8,PIDVALUE8" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10024++0x03 line.long 0x00 "TSD1_PID_VALUE_9,PIDVALUE9" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10028++0x03 line.long 0x00 "TSD1_PID_VALUE_10,PIDVALUE10" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x1002C++0x03 line.long 0x00 "TSD1_PID_VALUE_11,PIDVALUE11" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10030++0x03 line.long 0x00 "TSD1_PID_VALUE_12,PIDVALUE12" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10034++0x03 line.long 0x00 "TSD1_PID_VALUE_13,PIDVALUE13" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10038++0x03 line.long 0x00 "TSD1_PID_VALUE_14,PIDVALUE14" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x1003C++0x03 line.long 0x00 "TSD1_PID_VALUE_15,PIDVALUE15" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10040++0x03 line.long 0x00 "TSD1_PID_VALUE_16,PIDVALUE16" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10044++0x03 line.long 0x00 "TSD1_PID_VALUE_17,PIDVALUE17" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10048++0x03 line.long 0x00 "TSD1_PID_VALUE_18,PIDVALUE18" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x1004C++0x03 line.long 0x00 "TSD1_PID_VALUE_19,PIDVALUE19" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10050++0x03 line.long 0x00 "TSD1_PID_VALUE_20,PIDVALUE20" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10054++0x03 line.long 0x00 "TSD1_PID_VALUE_21,PIDVALUE21" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10058++0x03 line.long 0x00 "TSD1_PID_VALUE_22,PIDVALUE22" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x1005C++0x03 line.long 0x00 "TSD1_PID_VALUE_23,PIDVALUE23" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10060++0x03 line.long 0x00 "TSD1_PID_VALUE_24,PIDVALUE24" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10064++0x03 line.long 0x00 "TSD1_PID_VALUE_25,PIDVALUE25" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10068++0x03 line.long 0x00 "TSD1_PID_VALUE_26,PIDVALUE26" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x1006C++0x03 line.long 0x00 "TSD1_PID_VALUE_27,PIDVALUE27" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10070++0x03 line.long 0x00 "TSD1_PID_VALUE_28,PIDVALUE28" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10074++0x03 line.long 0x00 "TSD1_PID_VALUE_29,PIDVALUE29" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x10078++0x03 line.long 0x00 "TSD1_PID_VALUE_30,PIDVALUE30" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x1007C++0x03 line.long 0x00 "TSD1_PID_VALUE_31,PIDVALUE31" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" tree.end tree "TSD2" wgroup.long 0x110000++0x03 line.long 0x00 "TSD2_PID_VALUE_0,PIDVALUE0" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110004++0x03 line.long 0x00 "TSD2_PID_VALUE_1,PIDVALUE1" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110008++0x03 line.long 0x00 "TSD2_PID_VALUE_2,PIDVALUE2" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x11000C++0x03 line.long 0x00 "TSD2_PID_VALUE_3,PIDVALUE3" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110010++0x03 line.long 0x00 "TSD2_PID_VALUE_4,PIDVALUE4" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110014++0x03 line.long 0x00 "TSD2_PID_VALUE_5,PIDVALUE5" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110018++0x03 line.long 0x00 "TSD2_PID_VALUE_6,PIDVALUE6" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x11001C++0x03 line.long 0x00 "TSD2_PID_VALUE_7,PIDVALUE7" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110020++0x03 line.long 0x00 "TSD2_PID_VALUE_8,PIDVALUE8" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110024++0x03 line.long 0x00 "TSD2_PID_VALUE_9,PIDVALUE9" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110028++0x03 line.long 0x00 "TSD2_PID_VALUE_10,PIDVALUE10" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x11002C++0x03 line.long 0x00 "TSD2_PID_VALUE_11,PIDVALUE11" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110030++0x03 line.long 0x00 "TSD2_PID_VALUE_12,PIDVALUE12" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110034++0x03 line.long 0x00 "TSD2_PID_VALUE_13,PIDVALUE13" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110038++0x03 line.long 0x00 "TSD2_PID_VALUE_14,PIDVALUE14" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x11003C++0x03 line.long 0x00 "TSD2_PID_VALUE_15,PIDVALUE15" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110040++0x03 line.long 0x00 "TSD2_PID_VALUE_16,PIDVALUE16" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110044++0x03 line.long 0x00 "TSD2_PID_VALUE_17,PIDVALUE17" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110048++0x03 line.long 0x00 "TSD2_PID_VALUE_18,PIDVALUE18" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x11004C++0x03 line.long 0x00 "TSD2_PID_VALUE_19,PIDVALUE19" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110050++0x03 line.long 0x00 "TSD2_PID_VALUE_20,PIDVALUE20" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110054++0x03 line.long 0x00 "TSD2_PID_VALUE_21,PIDVALUE21" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110058++0x03 line.long 0x00 "TSD2_PID_VALUE_22,PIDVALUE22" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x11005C++0x03 line.long 0x00 "TSD2_PID_VALUE_23,PIDVALUE23" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110060++0x03 line.long 0x00 "TSD2_PID_VALUE_24,PIDVALUE24" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110064++0x03 line.long 0x00 "TSD2_PID_VALUE_25,PIDVALUE25" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110068++0x03 line.long 0x00 "TSD2_PID_VALUE_26,PIDVALUE26" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x11006C++0x03 line.long 0x00 "TSD2_PID_VALUE_27,PIDVALUE27" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110070++0x03 line.long 0x00 "TSD2_PID_VALUE_28,PIDVALUE28" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110074++0x03 line.long 0x00 "TSD2_PID_VALUE_29,PIDVALUE29" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x110078++0x03 line.long 0x00 "TSD2_PID_VALUE_30,PIDVALUE30" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" wgroup.long 0x11007C++0x03 line.long 0x00 "TSD2_PID_VALUE_31,PIDVALUE31" bitfld.long 0x00 31. " PIDBIT31 , PID channel 31 Value" "0,1" bitfld.long 0x00 30. " PIDBIT30 , PID channel 30 Value" "0,1" bitfld.long 0x00 29. " PIDBIT29 , PID channel 29 Value" "0,1" bitfld.long 0x00 28. " PIDBIT28 , PID channel 28 Value" "0,1" bitfld.long 0x00 27. " PIDBIT27 , PID channel 27 Value" "0,1" bitfld.long 0x00 26. " PIDBIT26 , PID channel 26 Value" "0,1" textline " " bitfld.long 0x00 25. " PIDBIT25 , PID channel 25 Value" "0,1" bitfld.long 0x00 24. " PIDBIT24 , PID channel 24 Value" "0,1" bitfld.long 0x00 23. " PIDBIT23 , PID channel 23 Value" "0,1" bitfld.long 0x00 22. " PIDBIT22 , PID channel 22 Value" "0,1" bitfld.long 0x00 21. " PIDBIT21 , PID channel 21 Value" "0,1" bitfld.long 0x00 20. " PIDBIT20 , PID channel 20 Value" "0,1" textline " " bitfld.long 0x00 19. " PIDBIT19 , PID channel 19 Value" "0,1" bitfld.long 0x00 18. " PIDBIT18 , PID channel 18 Value" "0,1" bitfld.long 0x00 17. " PIDBIT17 , PID channel 17 Value" "0,1" bitfld.long 0x00 16. " PIDBIT16 , PID channel 16 Value" "0,1" bitfld.long 0x00 15. " PIDBIT15 , PID channel 15 Value" "0,1" bitfld.long 0x00 14. " PIDBIT14 , PID channel 14 Value" "0,1" textline " " bitfld.long 0x00 13. " PIDBIT13 , PID channel 13 Value" "0,1" bitfld.long 0x00 12. " PIDBIT12 , PID channel 12 Value" "0,1" bitfld.long 0x00 11. " PIDBIT11 , PID channel 11 Value" "0,1" bitfld.long 0x00 10. " PIDBIT10 , PID channel 10 Value" "0,1" bitfld.long 0x00 9. " PIDBIT9 , PID channel 9 Value" "0,1" bitfld.long 0x00 8. " PIDBIT8 , PID channel 8 Value" "0,1" textline " " bitfld.long 0x00 7. " PIDBIT7 , PID channel 7 Value" "0,1" bitfld.long 0x00 6. " PIDBIT6 , PID channel 6 Value" "0,1" bitfld.long 0x00 5. " PIDBIT5 , PID channel 5 Value" "0,1" bitfld.long 0x00 4. " PIDBIT4 , PID channel 4 Value" "0,1" bitfld.long 0x00 3. " PIDBIT3 , PID channel 3 Value" "0,1" bitfld.long 0x00 2. " PIDBIT2 , PID channel 2 Value" "0,1" textline " " bitfld.long 0x00 1. " PIDBIT1 , PID channel 1 Value" "0,1" bitfld.long 0x00 0. " PIDBIT0 , PID channel 0 Value" "0,1" tree.end tree.end tree "PID Configuration" tree "TSD1" wgroup.long (ad:0xC0000000+0x10034)++0x3 line.long 0x0 "TSD1_PID0_CONFIG_1,PID channel 0 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x10034+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10034+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10034+0x4)++0x3 line.long 0x0 "TSD1_PID0_CONFIG_2,PID channel 0 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x10034+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10034+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10034+0x4)++0x3 line.long 0x0 "TSD1_PID0_CONFIG_2,PID channel 0 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10034+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10034+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10034+0x4)++0x3 line.long 0x0 "TSD1_PID0_CONFIG_2,PID channel 0 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10034+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10034+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10034+0x4)++0x3 line.long 0x0 "TSD1_PID0_CONFIG_2,PID channel 0 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x1003C)++0x3 line.long 0x0 "TSD1_PID1_CONFIG_1,PID channel 1 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1003C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1003C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1003C+0x4)++0x3 line.long 0x0 "TSD1_PID1_CONFIG_2,PID channel 1 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1003C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1003C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1003C+0x4)++0x3 line.long 0x0 "TSD1_PID1_CONFIG_2,PID channel 1 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1003C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1003C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1003C+0x4)++0x3 line.long 0x0 "TSD1_PID1_CONFIG_2,PID channel 1 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1003C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1003C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1003C+0x4)++0x3 line.long 0x0 "TSD1_PID1_CONFIG_2,PID channel 1 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x10044)++0x3 line.long 0x0 "TSD1_PID2_CONFIG_1,PID channel 2 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x10044+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10044+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10044+0x4)++0x3 line.long 0x0 "TSD1_PID2_CONFIG_2,PID channel 2 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x10044+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10044+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10044+0x4)++0x3 line.long 0x0 "TSD1_PID2_CONFIG_2,PID channel 2 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10044+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10044+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10044+0x4)++0x3 line.long 0x0 "TSD1_PID2_CONFIG_2,PID channel 2 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10044+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10044+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10044+0x4)++0x3 line.long 0x0 "TSD1_PID2_CONFIG_2,PID channel 2 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x1004C)++0x3 line.long 0x0 "TSD1_PID3_CONFIG_1,PID channel 3 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1004C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1004C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1004C+0x4)++0x3 line.long 0x0 "TSD1_PID3_CONFIG_2,PID channel 3 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1004C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1004C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1004C+0x4)++0x3 line.long 0x0 "TSD1_PID3_CONFIG_2,PID channel 3 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1004C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1004C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1004C+0x4)++0x3 line.long 0x0 "TSD1_PID3_CONFIG_2,PID channel 3 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1004C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1004C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1004C+0x4)++0x3 line.long 0x0 "TSD1_PID3_CONFIG_2,PID channel 3 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x10054)++0x3 line.long 0x0 "TSD1_PID4_CONFIG_1,PID channel 4 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x10054+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10054+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10054+0x4)++0x3 line.long 0x0 "TSD1_PID4_CONFIG_2,PID channel 4 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x10054+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10054+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10054+0x4)++0x3 line.long 0x0 "TSD1_PID4_CONFIG_2,PID channel 4 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10054+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10054+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10054+0x4)++0x3 line.long 0x0 "TSD1_PID4_CONFIG_2,PID channel 4 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10054+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10054+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10054+0x4)++0x3 line.long 0x0 "TSD1_PID4_CONFIG_2,PID channel 4 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x1005C)++0x3 line.long 0x0 "TSD1_PID5_CONFIG_1,PID channel 5 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1005C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1005C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1005C+0x4)++0x3 line.long 0x0 "TSD1_PID5_CONFIG_2,PID channel 5 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1005C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1005C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1005C+0x4)++0x3 line.long 0x0 "TSD1_PID5_CONFIG_2,PID channel 5 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1005C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1005C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1005C+0x4)++0x3 line.long 0x0 "TSD1_PID5_CONFIG_2,PID channel 5 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1005C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1005C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1005C+0x4)++0x3 line.long 0x0 "TSD1_PID5_CONFIG_2,PID channel 5 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x10064)++0x3 line.long 0x0 "TSD1_PID6_CONFIG_1,PID channel 6 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x10064+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10064+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10064+0x4)++0x3 line.long 0x0 "TSD1_PID6_CONFIG_2,PID channel 6 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x10064+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10064+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10064+0x4)++0x3 line.long 0x0 "TSD1_PID6_CONFIG_2,PID channel 6 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10064+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10064+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10064+0x4)++0x3 line.long 0x0 "TSD1_PID6_CONFIG_2,PID channel 6 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10064+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10064+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10064+0x4)++0x3 line.long 0x0 "TSD1_PID6_CONFIG_2,PID channel 6 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x1006C)++0x3 line.long 0x0 "TSD1_PID7_CONFIG_1,PID channel 7 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1006C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1006C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1006C+0x4)++0x3 line.long 0x0 "TSD1_PID7_CONFIG_2,PID channel 7 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1006C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1006C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1006C+0x4)++0x3 line.long 0x0 "TSD1_PID7_CONFIG_2,PID channel 7 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1006C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1006C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1006C+0x4)++0x3 line.long 0x0 "TSD1_PID7_CONFIG_2,PID channel 7 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1006C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1006C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1006C+0x4)++0x3 line.long 0x0 "TSD1_PID7_CONFIG_2,PID channel 7 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x10074)++0x3 line.long 0x0 "TSD1_PID8_CONFIG_1,PID channel 8 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x10074+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10074+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10074+0x4)++0x3 line.long 0x0 "TSD1_PID8_CONFIG_2,PID channel 8 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x10074+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10074+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10074+0x4)++0x3 line.long 0x0 "TSD1_PID8_CONFIG_2,PID channel 8 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10074+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10074+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10074+0x4)++0x3 line.long 0x0 "TSD1_PID8_CONFIG_2,PID channel 8 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10074+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10074+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10074+0x4)++0x3 line.long 0x0 "TSD1_PID8_CONFIG_2,PID channel 8 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x1007C)++0x3 line.long 0x0 "TSD1_PID9_CONFIG_1,PID channel 9 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1007C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1007C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1007C+0x4)++0x3 line.long 0x0 "TSD1_PID9_CONFIG_2,PID channel 9 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1007C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1007C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1007C+0x4)++0x3 line.long 0x0 "TSD1_PID9_CONFIG_2,PID channel 9 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1007C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1007C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1007C+0x4)++0x3 line.long 0x0 "TSD1_PID9_CONFIG_2,PID channel 9 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1007C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1007C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1007C+0x4)++0x3 line.long 0x0 "TSD1_PID9_CONFIG_2,PID channel 9 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x10084)++0x3 line.long 0x0 "TSD1_PID10_CONFIG_1,PID channel 10 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x10084+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10084+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10084+0x4)++0x3 line.long 0x0 "TSD1_PID10_CONFIG_2,PID channel 10 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x10084+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10084+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10084+0x4)++0x3 line.long 0x0 "TSD1_PID10_CONFIG_2,PID channel 10 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10084+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10084+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10084+0x4)++0x3 line.long 0x0 "TSD1_PID10_CONFIG_2,PID channel 10 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10084+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10084+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10084+0x4)++0x3 line.long 0x0 "TSD1_PID10_CONFIG_2,PID channel 10 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x1008C)++0x3 line.long 0x0 "TSD1_PID11_CONFIG_1,PID channel 11 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1008C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1008C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1008C+0x4)++0x3 line.long 0x0 "TSD1_PID11_CONFIG_2,PID channel 11 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1008C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1008C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1008C+0x4)++0x3 line.long 0x0 "TSD1_PID11_CONFIG_2,PID channel 11 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1008C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1008C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1008C+0x4)++0x3 line.long 0x0 "TSD1_PID11_CONFIG_2,PID channel 11 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1008C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1008C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1008C+0x4)++0x3 line.long 0x0 "TSD1_PID11_CONFIG_2,PID channel 11 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x10094)++0x3 line.long 0x0 "TSD1_PID12_CONFIG_1,PID channel 12 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x10094+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10094+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10094+0x4)++0x3 line.long 0x0 "TSD1_PID12_CONFIG_2,PID channel 12 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x10094+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10094+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10094+0x4)++0x3 line.long 0x0 "TSD1_PID12_CONFIG_2,PID channel 12 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10094+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10094+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10094+0x4)++0x3 line.long 0x0 "TSD1_PID12_CONFIG_2,PID channel 12 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10094+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10094+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10094+0x4)++0x3 line.long 0x0 "TSD1_PID12_CONFIG_2,PID channel 12 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x1009C)++0x3 line.long 0x0 "TSD1_PID13_CONFIG_1,PID channel 13 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1009C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1009C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1009C+0x4)++0x3 line.long 0x0 "TSD1_PID13_CONFIG_2,PID channel 13 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1009C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1009C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1009C+0x4)++0x3 line.long 0x0 "TSD1_PID13_CONFIG_2,PID channel 13 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1009C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1009C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1009C+0x4)++0x3 line.long 0x0 "TSD1_PID13_CONFIG_2,PID channel 13 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1009C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1009C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1009C+0x4)++0x3 line.long 0x0 "TSD1_PID13_CONFIG_2,PID channel 13 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x100A4)++0x3 line.long 0x0 "TSD1_PID14_CONFIG_1,PID channel 14 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x100A4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100A4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100A4+0x4)++0x3 line.long 0x0 "TSD1_PID14_CONFIG_2,PID channel 14 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x100A4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100A4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100A4+0x4)++0x3 line.long 0x0 "TSD1_PID14_CONFIG_2,PID channel 14 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100A4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100A4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100A4+0x4)++0x3 line.long 0x0 "TSD1_PID14_CONFIG_2,PID channel 14 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100A4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100A4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100A4+0x4)++0x3 line.long 0x0 "TSD1_PID14_CONFIG_2,PID channel 14 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x100AC)++0x3 line.long 0x0 "TSD1_PID15_CONFIG_1,PID channel 15 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x100AC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100AC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100AC+0x4)++0x3 line.long 0x0 "TSD1_PID15_CONFIG_2,PID channel 15 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x100AC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100AC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100AC+0x4)++0x3 line.long 0x0 "TSD1_PID15_CONFIG_2,PID channel 15 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100AC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100AC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100AC+0x4)++0x3 line.long 0x0 "TSD1_PID15_CONFIG_2,PID channel 15 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100AC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100AC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100AC+0x4)++0x3 line.long 0x0 "TSD1_PID15_CONFIG_2,PID channel 15 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x100B4)++0x3 line.long 0x0 "TSD1_PID16_CONFIG_1,PID channel 16 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x100B4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100B4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100B4+0x4)++0x3 line.long 0x0 "TSD1_PID16_CONFIG_2,PID channel 16 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x100B4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100B4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100B4+0x4)++0x3 line.long 0x0 "TSD1_PID16_CONFIG_2,PID channel 16 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100B4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100B4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100B4+0x4)++0x3 line.long 0x0 "TSD1_PID16_CONFIG_2,PID channel 16 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100B4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100B4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100B4+0x4)++0x3 line.long 0x0 "TSD1_PID16_CONFIG_2,PID channel 16 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x100BC)++0x3 line.long 0x0 "TSD1_PID17_CONFIG_1,PID channel 17 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x100BC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100BC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100BC+0x4)++0x3 line.long 0x0 "TSD1_PID17_CONFIG_2,PID channel 17 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x100BC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100BC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100BC+0x4)++0x3 line.long 0x0 "TSD1_PID17_CONFIG_2,PID channel 17 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100BC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100BC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100BC+0x4)++0x3 line.long 0x0 "TSD1_PID17_CONFIG_2,PID channel 17 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100BC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100BC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100BC+0x4)++0x3 line.long 0x0 "TSD1_PID17_CONFIG_2,PID channel 17 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x100C4)++0x3 line.long 0x0 "TSD1_PID18_CONFIG_1,PID channel 18 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x100C4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100C4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100C4+0x4)++0x3 line.long 0x0 "TSD1_PID18_CONFIG_2,PID channel 18 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x100C4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100C4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100C4+0x4)++0x3 line.long 0x0 "TSD1_PID18_CONFIG_2,PID channel 18 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100C4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100C4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100C4+0x4)++0x3 line.long 0x0 "TSD1_PID18_CONFIG_2,PID channel 18 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100C4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100C4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100C4+0x4)++0x3 line.long 0x0 "TSD1_PID18_CONFIG_2,PID channel 18 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x100CC)++0x3 line.long 0x0 "TSD1_PID19_CONFIG_1,PID channel 19 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x100CC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100CC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100CC+0x4)++0x3 line.long 0x0 "TSD1_PID19_CONFIG_2,PID channel 19 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x100CC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100CC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100CC+0x4)++0x3 line.long 0x0 "TSD1_PID19_CONFIG_2,PID channel 19 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100CC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100CC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100CC+0x4)++0x3 line.long 0x0 "TSD1_PID19_CONFIG_2,PID channel 19 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100CC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100CC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100CC+0x4)++0x3 line.long 0x0 "TSD1_PID19_CONFIG_2,PID channel 19 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x100D4)++0x3 line.long 0x0 "TSD1_PID20_CONFIG_1,PID channel 20 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x100D4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100D4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100D4+0x4)++0x3 line.long 0x0 "TSD1_PID20_CONFIG_2,PID channel 20 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x100D4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100D4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100D4+0x4)++0x3 line.long 0x0 "TSD1_PID20_CONFIG_2,PID channel 20 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100D4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100D4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100D4+0x4)++0x3 line.long 0x0 "TSD1_PID20_CONFIG_2,PID channel 20 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100D4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100D4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100D4+0x4)++0x3 line.long 0x0 "TSD1_PID20_CONFIG_2,PID channel 20 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x100DC)++0x3 line.long 0x0 "TSD1_PID21_CONFIG_1,PID channel 21 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x100DC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100DC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100DC+0x4)++0x3 line.long 0x0 "TSD1_PID21_CONFIG_2,PID channel 21 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x100DC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100DC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100DC+0x4)++0x3 line.long 0x0 "TSD1_PID21_CONFIG_2,PID channel 21 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100DC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100DC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100DC+0x4)++0x3 line.long 0x0 "TSD1_PID21_CONFIG_2,PID channel 21 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100DC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100DC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100DC+0x4)++0x3 line.long 0x0 "TSD1_PID21_CONFIG_2,PID channel 21 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x100E4)++0x3 line.long 0x0 "TSD1_PID22_CONFIG_1,PID channel 22 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x100E4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100E4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100E4+0x4)++0x3 line.long 0x0 "TSD1_PID22_CONFIG_2,PID channel 22 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x100E4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100E4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100E4+0x4)++0x3 line.long 0x0 "TSD1_PID22_CONFIG_2,PID channel 22 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100E4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100E4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100E4+0x4)++0x3 line.long 0x0 "TSD1_PID22_CONFIG_2,PID channel 22 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100E4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100E4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100E4+0x4)++0x3 line.long 0x0 "TSD1_PID22_CONFIG_2,PID channel 22 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x100EC)++0x3 line.long 0x0 "TSD1_PID23_CONFIG_1,PID channel 23 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x100EC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100EC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100EC+0x4)++0x3 line.long 0x0 "TSD1_PID23_CONFIG_2,PID channel 23 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x100EC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100EC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100EC+0x4)++0x3 line.long 0x0 "TSD1_PID23_CONFIG_2,PID channel 23 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100EC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100EC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100EC+0x4)++0x3 line.long 0x0 "TSD1_PID23_CONFIG_2,PID channel 23 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100EC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100EC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100EC+0x4)++0x3 line.long 0x0 "TSD1_PID23_CONFIG_2,PID channel 23 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x100F4)++0x3 line.long 0x0 "TSD1_PID24_CONFIG_1,PID channel 24 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x100F4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100F4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100F4+0x4)++0x3 line.long 0x0 "TSD1_PID24_CONFIG_2,PID channel 24 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x100F4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100F4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100F4+0x4)++0x3 line.long 0x0 "TSD1_PID24_CONFIG_2,PID channel 24 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100F4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100F4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100F4+0x4)++0x3 line.long 0x0 "TSD1_PID24_CONFIG_2,PID channel 24 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100F4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100F4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100F4+0x4)++0x3 line.long 0x0 "TSD1_PID24_CONFIG_2,PID channel 24 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x100FC)++0x3 line.long 0x0 "TSD1_PID25_CONFIG_1,PID channel 25 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x100FC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100FC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100FC+0x4)++0x3 line.long 0x0 "TSD1_PID25_CONFIG_2,PID channel 25 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x100FC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x100FC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100FC+0x4)++0x3 line.long 0x0 "TSD1_PID25_CONFIG_2,PID channel 25 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100FC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100FC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x100FC+0x4)++0x3 line.long 0x0 "TSD1_PID25_CONFIG_2,PID channel 25 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x100FC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x100FC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x100FC+0x4)++0x3 line.long 0x0 "TSD1_PID25_CONFIG_2,PID channel 25 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x10104)++0x3 line.long 0x0 "TSD1_PID26_CONFIG_1,PID channel 26 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x10104+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10104+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10104+0x4)++0x3 line.long 0x0 "TSD1_PID26_CONFIG_2,PID channel 26 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x10104+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10104+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10104+0x4)++0x3 line.long 0x0 "TSD1_PID26_CONFIG_2,PID channel 26 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10104+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10104+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10104+0x4)++0x3 line.long 0x0 "TSD1_PID26_CONFIG_2,PID channel 26 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10104+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10104+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10104+0x4)++0x3 line.long 0x0 "TSD1_PID26_CONFIG_2,PID channel 26 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x1010C)++0x3 line.long 0x0 "TSD1_PID27_CONFIG_1,PID channel 27 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1010C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1010C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1010C+0x4)++0x3 line.long 0x0 "TSD1_PID27_CONFIG_2,PID channel 27 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1010C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1010C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1010C+0x4)++0x3 line.long 0x0 "TSD1_PID27_CONFIG_2,PID channel 27 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1010C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1010C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1010C+0x4)++0x3 line.long 0x0 "TSD1_PID27_CONFIG_2,PID channel 27 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1010C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1010C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1010C+0x4)++0x3 line.long 0x0 "TSD1_PID27_CONFIG_2,PID channel 27 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x10114)++0x3 line.long 0x0 "TSD1_PID28_CONFIG_1,PID channel 28 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x10114+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10114+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10114+0x4)++0x3 line.long 0x0 "TSD1_PID28_CONFIG_2,PID channel 28 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x10114+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10114+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10114+0x4)++0x3 line.long 0x0 "TSD1_PID28_CONFIG_2,PID channel 28 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10114+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10114+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10114+0x4)++0x3 line.long 0x0 "TSD1_PID28_CONFIG_2,PID channel 28 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10114+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10114+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10114+0x4)++0x3 line.long 0x0 "TSD1_PID28_CONFIG_2,PID channel 28 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x1011C)++0x3 line.long 0x0 "TSD1_PID29_CONFIG_1,PID channel 29 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1011C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1011C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1011C+0x4)++0x3 line.long 0x0 "TSD1_PID29_CONFIG_2,PID channel 29 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1011C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1011C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1011C+0x4)++0x3 line.long 0x0 "TSD1_PID29_CONFIG_2,PID channel 29 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1011C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1011C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1011C+0x4)++0x3 line.long 0x0 "TSD1_PID29_CONFIG_2,PID channel 29 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1011C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1011C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1011C+0x4)++0x3 line.long 0x0 "TSD1_PID29_CONFIG_2,PID channel 29 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x10124)++0x3 line.long 0x0 "TSD1_PID30_CONFIG_1,PID channel 30 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x10124+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10124+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10124+0x4)++0x3 line.long 0x0 "TSD1_PID30_CONFIG_2,PID channel 30 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x10124+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x10124+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10124+0x4)++0x3 line.long 0x0 "TSD1_PID30_CONFIG_2,PID channel 30 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10124+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10124+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x10124+0x4)++0x3 line.long 0x0 "TSD1_PID30_CONFIG_2,PID channel 30 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x10124+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x10124+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x10124+0x4)++0x3 line.long 0x0 "TSD1_PID30_CONFIG_2,PID channel 30 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif wgroup.long (ad:0xC0000000+0x1012C)++0x3 line.long 0x0 "TSD1_PID31_CONFIG_1,PID channel 31 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activate,Not activate" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disable,Enable" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1012C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1012C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1012C+0x4)++0x3 line.long 0x0 "TSD1_PID31_CONFIG_2,PID channel 31 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1012C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1012C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1012C+0x4)++0x3 line.long 0x0 "TSD1_PID31_CONFIG_2,PID channel 31 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1012C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1012C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1012C+0x4)++0x3 line.long 0x0 "TSD1_PID31_CONFIG_2,PID channel 31 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" elif ((((per.l(ad:0xC0000000+0x1012C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1012C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1012C+0x4)++0x3 line.long 0x0 "TSD1_PID31_CONFIG_2,PID channel 31 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disabled,Enabled" endif tree.end tree "TSD2" wgroup.long (ad:0xC0000000+0x110034)++0x3 line.long 0x0 "TSD2_PID0_CONFIG_1,PID channel 0 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x110034+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110034+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110034+0x4)++0x3 line.long 0x0 "TSD2_PID0_CONFIG_2,PID channel 0 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x110034+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110034+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110034+0x4)++0x3 line.long 0x0 "TSD2_PID0_CONFIG_2,PID channel 0 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110034+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110034+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110034+0x4)++0x3 line.long 0x0 "TSD2_PID0_CONFIG_2,PID channel 0 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110034+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110034+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110034+0x4)++0x3 line.long 0x0 "TSD2_PID0_CONFIG_2,PID channel 0 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x11003C)++0x3 line.long 0x0 "TSD2_PID1_CONFIG_1,PID channel 1 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x11003C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11003C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11003C+0x4)++0x3 line.long 0x0 "TSD2_PID1_CONFIG_2,PID channel 1 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x11003C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11003C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11003C+0x4)++0x3 line.long 0x0 "TSD2_PID1_CONFIG_2,PID channel 1 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11003C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11003C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11003C+0x4)++0x3 line.long 0x0 "TSD2_PID1_CONFIG_2,PID channel 1 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11003C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11003C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11003C+0x4)++0x3 line.long 0x0 "TSD2_PID1_CONFIG_2,PID channel 1 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x110044)++0x3 line.long 0x0 "TSD2_PID2_CONFIG_1,PID channel 2 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x110044+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110044+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110044+0x4)++0x3 line.long 0x0 "TSD2_PID2_CONFIG_2,PID channel 2 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x110044+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110044+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110044+0x4)++0x3 line.long 0x0 "TSD2_PID2_CONFIG_2,PID channel 2 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110044+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110044+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110044+0x4)++0x3 line.long 0x0 "TSD2_PID2_CONFIG_2,PID channel 2 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110044+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110044+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110044+0x4)++0x3 line.long 0x0 "TSD2_PID2_CONFIG_2,PID channel 2 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x11004C)++0x3 line.long 0x0 "TSD2_PID3_CONFIG_1,PID channel 3 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x11004C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11004C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11004C+0x4)++0x3 line.long 0x0 "TSD2_PID3_CONFIG_2,PID channel 3 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x11004C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11004C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11004C+0x4)++0x3 line.long 0x0 "TSD2_PID3_CONFIG_2,PID channel 3 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11004C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11004C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11004C+0x4)++0x3 line.long 0x0 "TSD2_PID3_CONFIG_2,PID channel 3 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11004C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11004C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11004C+0x4)++0x3 line.long 0x0 "TSD2_PID3_CONFIG_2,PID channel 3 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x110054)++0x3 line.long 0x0 "TSD2_PID4_CONFIG_1,PID channel 4 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x110054+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110054+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110054+0x4)++0x3 line.long 0x0 "TSD2_PID4_CONFIG_2,PID channel 4 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x110054+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110054+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110054+0x4)++0x3 line.long 0x0 "TSD2_PID4_CONFIG_2,PID channel 4 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110054+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110054+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110054+0x4)++0x3 line.long 0x0 "TSD2_PID4_CONFIG_2,PID channel 4 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110054+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110054+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110054+0x4)++0x3 line.long 0x0 "TSD2_PID4_CONFIG_2,PID channel 4 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x11005C)++0x3 line.long 0x0 "TSD2_PID5_CONFIG_1,PID channel 5 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x11005C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11005C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11005C+0x4)++0x3 line.long 0x0 "TSD2_PID5_CONFIG_2,PID channel 5 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x11005C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11005C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11005C+0x4)++0x3 line.long 0x0 "TSD2_PID5_CONFIG_2,PID channel 5 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11005C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11005C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11005C+0x4)++0x3 line.long 0x0 "TSD2_PID5_CONFIG_2,PID channel 5 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11005C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11005C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11005C+0x4)++0x3 line.long 0x0 "TSD2_PID5_CONFIG_2,PID channel 5 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x110064)++0x3 line.long 0x0 "TSD2_PID6_CONFIG_1,PID channel 6 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x110064+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110064+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110064+0x4)++0x3 line.long 0x0 "TSD2_PID6_CONFIG_2,PID channel 6 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x110064+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110064+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110064+0x4)++0x3 line.long 0x0 "TSD2_PID6_CONFIG_2,PID channel 6 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110064+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110064+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110064+0x4)++0x3 line.long 0x0 "TSD2_PID6_CONFIG_2,PID channel 6 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110064+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110064+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110064+0x4)++0x3 line.long 0x0 "TSD2_PID6_CONFIG_2,PID channel 6 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x11006C)++0x3 line.long 0x0 "TSD2_PID7_CONFIG_1,PID channel 7 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x11006C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11006C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11006C+0x4)++0x3 line.long 0x0 "TSD2_PID7_CONFIG_2,PID channel 7 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x11006C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11006C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11006C+0x4)++0x3 line.long 0x0 "TSD2_PID7_CONFIG_2,PID channel 7 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11006C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11006C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11006C+0x4)++0x3 line.long 0x0 "TSD2_PID7_CONFIG_2,PID channel 7 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11006C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11006C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11006C+0x4)++0x3 line.long 0x0 "TSD2_PID7_CONFIG_2,PID channel 7 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x110074)++0x3 line.long 0x0 "TSD2_PID8_CONFIG_1,PID channel 8 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x110074+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110074+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110074+0x4)++0x3 line.long 0x0 "TSD2_PID8_CONFIG_2,PID channel 8 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x110074+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110074+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110074+0x4)++0x3 line.long 0x0 "TSD2_PID8_CONFIG_2,PID channel 8 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110074+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110074+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110074+0x4)++0x3 line.long 0x0 "TSD2_PID8_CONFIG_2,PID channel 8 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110074+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110074+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110074+0x4)++0x3 line.long 0x0 "TSD2_PID8_CONFIG_2,PID channel 8 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x11007C)++0x3 line.long 0x0 "TSD2_PID9_CONFIG_1,PID channel 9 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x11007C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11007C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11007C+0x4)++0x3 line.long 0x0 "TSD2_PID9_CONFIG_2,PID channel 9 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x11007C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11007C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11007C+0x4)++0x3 line.long 0x0 "TSD2_PID9_CONFIG_2,PID channel 9 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11007C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11007C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11007C+0x4)++0x3 line.long 0x0 "TSD2_PID9_CONFIG_2,PID channel 9 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11007C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11007C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11007C+0x4)++0x3 line.long 0x0 "TSD2_PID9_CONFIG_2,PID channel 9 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x110084)++0x3 line.long 0x0 "TSD2_PID10_CONFIG_1,PID channel 10 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x110084+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110084+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110084+0x4)++0x3 line.long 0x0 "TSD2_PID10_CONFIG_2,PID channel 10 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x110084+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110084+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110084+0x4)++0x3 line.long 0x0 "TSD2_PID10_CONFIG_2,PID channel 10 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110084+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110084+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110084+0x4)++0x3 line.long 0x0 "TSD2_PID10_CONFIG_2,PID channel 10 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110084+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110084+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110084+0x4)++0x3 line.long 0x0 "TSD2_PID10_CONFIG_2,PID channel 10 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x11008C)++0x3 line.long 0x0 "TSD2_PID11_CONFIG_1,PID channel 11 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x11008C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11008C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11008C+0x4)++0x3 line.long 0x0 "TSD2_PID11_CONFIG_2,PID channel 11 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x11008C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11008C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11008C+0x4)++0x3 line.long 0x0 "TSD2_PID11_CONFIG_2,PID channel 11 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11008C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11008C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11008C+0x4)++0x3 line.long 0x0 "TSD2_PID11_CONFIG_2,PID channel 11 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11008C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11008C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11008C+0x4)++0x3 line.long 0x0 "TSD2_PID11_CONFIG_2,PID channel 11 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x110094)++0x3 line.long 0x0 "TSD2_PID12_CONFIG_1,PID channel 12 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x110094+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110094+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110094+0x4)++0x3 line.long 0x0 "TSD2_PID12_CONFIG_2,PID channel 12 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x110094+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110094+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110094+0x4)++0x3 line.long 0x0 "TSD2_PID12_CONFIG_2,PID channel 12 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110094+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110094+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110094+0x4)++0x3 line.long 0x0 "TSD2_PID12_CONFIG_2,PID channel 12 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110094+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110094+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110094+0x4)++0x3 line.long 0x0 "TSD2_PID12_CONFIG_2,PID channel 12 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x11009C)++0x3 line.long 0x0 "TSD2_PID13_CONFIG_1,PID channel 13 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x11009C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11009C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11009C+0x4)++0x3 line.long 0x0 "TSD2_PID13_CONFIG_2,PID channel 13 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x11009C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11009C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11009C+0x4)++0x3 line.long 0x0 "TSD2_PID13_CONFIG_2,PID channel 13 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11009C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11009C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11009C+0x4)++0x3 line.long 0x0 "TSD2_PID13_CONFIG_2,PID channel 13 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11009C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11009C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11009C+0x4)++0x3 line.long 0x0 "TSD2_PID13_CONFIG_2,PID channel 13 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x1100A4)++0x3 line.long 0x0 "TSD2_PID14_CONFIG_1,PID channel 14 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1100A4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100A4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100A4+0x4)++0x3 line.long 0x0 "TSD2_PID14_CONFIG_2,PID channel 14 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1100A4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100A4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100A4+0x4)++0x3 line.long 0x0 "TSD2_PID14_CONFIG_2,PID channel 14 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100A4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100A4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100A4+0x4)++0x3 line.long 0x0 "TSD2_PID14_CONFIG_2,PID channel 14 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100A4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100A4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100A4+0x4)++0x3 line.long 0x0 "TSD2_PID14_CONFIG_2,PID channel 14 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x1100AC)++0x3 line.long 0x0 "TSD2_PID15_CONFIG_1,PID channel 15 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1100AC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100AC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100AC+0x4)++0x3 line.long 0x0 "TSD2_PID15_CONFIG_2,PID channel 15 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1100AC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100AC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100AC+0x4)++0x3 line.long 0x0 "TSD2_PID15_CONFIG_2,PID channel 15 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100AC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100AC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100AC+0x4)++0x3 line.long 0x0 "TSD2_PID15_CONFIG_2,PID channel 15 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100AC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100AC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100AC+0x4)++0x3 line.long 0x0 "TSD2_PID15_CONFIG_2,PID channel 15 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x1100B4)++0x3 line.long 0x0 "TSD2_PID16_CONFIG_1,PID channel 16 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1100B4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100B4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100B4+0x4)++0x3 line.long 0x0 "TSD2_PID16_CONFIG_2,PID channel 16 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1100B4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100B4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100B4+0x4)++0x3 line.long 0x0 "TSD2_PID16_CONFIG_2,PID channel 16 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100B4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100B4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100B4+0x4)++0x3 line.long 0x0 "TSD2_PID16_CONFIG_2,PID channel 16 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100B4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100B4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100B4+0x4)++0x3 line.long 0x0 "TSD2_PID16_CONFIG_2,PID channel 16 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x1100BC)++0x3 line.long 0x0 "TSD2_PID17_CONFIG_1,PID channel 17 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1100BC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100BC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100BC+0x4)++0x3 line.long 0x0 "TSD2_PID17_CONFIG_2,PID channel 17 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1100BC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100BC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100BC+0x4)++0x3 line.long 0x0 "TSD2_PID17_CONFIG_2,PID channel 17 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100BC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100BC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100BC+0x4)++0x3 line.long 0x0 "TSD2_PID17_CONFIG_2,PID channel 17 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100BC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100BC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100BC+0x4)++0x3 line.long 0x0 "TSD2_PID17_CONFIG_2,PID channel 17 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x1100C4)++0x3 line.long 0x0 "TSD2_PID18_CONFIG_1,PID channel 18 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1100C4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100C4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100C4+0x4)++0x3 line.long 0x0 "TSD2_PID18_CONFIG_2,PID channel 18 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1100C4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100C4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100C4+0x4)++0x3 line.long 0x0 "TSD2_PID18_CONFIG_2,PID channel 18 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100C4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100C4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100C4+0x4)++0x3 line.long 0x0 "TSD2_PID18_CONFIG_2,PID channel 18 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100C4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100C4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100C4+0x4)++0x3 line.long 0x0 "TSD2_PID18_CONFIG_2,PID channel 18 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x1100CC)++0x3 line.long 0x0 "TSD2_PID19_CONFIG_1,PID channel 19 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1100CC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100CC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100CC+0x4)++0x3 line.long 0x0 "TSD2_PID19_CONFIG_2,PID channel 19 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1100CC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100CC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100CC+0x4)++0x3 line.long 0x0 "TSD2_PID19_CONFIG_2,PID channel 19 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100CC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100CC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100CC+0x4)++0x3 line.long 0x0 "TSD2_PID19_CONFIG_2,PID channel 19 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100CC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100CC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100CC+0x4)++0x3 line.long 0x0 "TSD2_PID19_CONFIG_2,PID channel 19 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x1100D4)++0x3 line.long 0x0 "TSD2_PID20_CONFIG_1,PID channel 20 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1100D4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100D4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100D4+0x4)++0x3 line.long 0x0 "TSD2_PID20_CONFIG_2,PID channel 20 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1100D4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100D4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100D4+0x4)++0x3 line.long 0x0 "TSD2_PID20_CONFIG_2,PID channel 20 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100D4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100D4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100D4+0x4)++0x3 line.long 0x0 "TSD2_PID20_CONFIG_2,PID channel 20 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100D4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100D4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100D4+0x4)++0x3 line.long 0x0 "TSD2_PID20_CONFIG_2,PID channel 20 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x1100DC)++0x3 line.long 0x0 "TSD2_PID21_CONFIG_1,PID channel 21 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1100DC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100DC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100DC+0x4)++0x3 line.long 0x0 "TSD2_PID21_CONFIG_2,PID channel 21 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1100DC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100DC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100DC+0x4)++0x3 line.long 0x0 "TSD2_PID21_CONFIG_2,PID channel 21 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100DC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100DC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100DC+0x4)++0x3 line.long 0x0 "TSD2_PID21_CONFIG_2,PID channel 21 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100DC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100DC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100DC+0x4)++0x3 line.long 0x0 "TSD2_PID21_CONFIG_2,PID channel 21 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x1100E4)++0x3 line.long 0x0 "TSD2_PID22_CONFIG_1,PID channel 22 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1100E4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100E4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100E4+0x4)++0x3 line.long 0x0 "TSD2_PID22_CONFIG_2,PID channel 22 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1100E4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100E4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100E4+0x4)++0x3 line.long 0x0 "TSD2_PID22_CONFIG_2,PID channel 22 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100E4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100E4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100E4+0x4)++0x3 line.long 0x0 "TSD2_PID22_CONFIG_2,PID channel 22 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100E4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100E4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100E4+0x4)++0x3 line.long 0x0 "TSD2_PID22_CONFIG_2,PID channel 22 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x1100EC)++0x3 line.long 0x0 "TSD2_PID23_CONFIG_1,PID channel 23 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1100EC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100EC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100EC+0x4)++0x3 line.long 0x0 "TSD2_PID23_CONFIG_2,PID channel 23 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1100EC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100EC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100EC+0x4)++0x3 line.long 0x0 "TSD2_PID23_CONFIG_2,PID channel 23 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100EC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100EC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100EC+0x4)++0x3 line.long 0x0 "TSD2_PID23_CONFIG_2,PID channel 23 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100EC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100EC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100EC+0x4)++0x3 line.long 0x0 "TSD2_PID23_CONFIG_2,PID channel 23 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x1100F4)++0x3 line.long 0x0 "TSD2_PID24_CONFIG_1,PID channel 24 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1100F4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100F4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100F4+0x4)++0x3 line.long 0x0 "TSD2_PID24_CONFIG_2,PID channel 24 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1100F4+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100F4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100F4+0x4)++0x3 line.long 0x0 "TSD2_PID24_CONFIG_2,PID channel 24 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100F4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100F4+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100F4+0x4)++0x3 line.long 0x0 "TSD2_PID24_CONFIG_2,PID channel 24 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100F4+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100F4+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100F4+0x4)++0x3 line.long 0x0 "TSD2_PID24_CONFIG_2,PID channel 24 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x1100FC)++0x3 line.long 0x0 "TSD2_PID25_CONFIG_1,PID channel 25 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x1100FC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100FC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100FC+0x4)++0x3 line.long 0x0 "TSD2_PID25_CONFIG_2,PID channel 25 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x1100FC+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x1100FC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100FC+0x4)++0x3 line.long 0x0 "TSD2_PID25_CONFIG_2,PID channel 25 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100FC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100FC+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x1100FC+0x4)++0x3 line.long 0x0 "TSD2_PID25_CONFIG_2,PID channel 25 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x1100FC+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x1100FC+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x1100FC+0x4)++0x3 line.long 0x0 "TSD2_PID25_CONFIG_2,PID channel 25 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x110104)++0x3 line.long 0x0 "TSD2_PID26_CONFIG_1,PID channel 26 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x110104+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110104+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110104+0x4)++0x3 line.long 0x0 "TSD2_PID26_CONFIG_2,PID channel 26 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x110104+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110104+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110104+0x4)++0x3 line.long 0x0 "TSD2_PID26_CONFIG_2,PID channel 26 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110104+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110104+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110104+0x4)++0x3 line.long 0x0 "TSD2_PID26_CONFIG_2,PID channel 26 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110104+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110104+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110104+0x4)++0x3 line.long 0x0 "TSD2_PID26_CONFIG_2,PID channel 26 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x11010C)++0x3 line.long 0x0 "TSD2_PID27_CONFIG_1,PID channel 27 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x11010C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11010C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11010C+0x4)++0x3 line.long 0x0 "TSD2_PID27_CONFIG_2,PID channel 27 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x11010C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11010C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11010C+0x4)++0x3 line.long 0x0 "TSD2_PID27_CONFIG_2,PID channel 27 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11010C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11010C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11010C+0x4)++0x3 line.long 0x0 "TSD2_PID27_CONFIG_2,PID channel 27 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11010C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11010C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11010C+0x4)++0x3 line.long 0x0 "TSD2_PID27_CONFIG_2,PID channel 27 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x110114)++0x3 line.long 0x0 "TSD2_PID28_CONFIG_1,PID channel 28 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x110114+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110114+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110114+0x4)++0x3 line.long 0x0 "TSD2_PID28_CONFIG_2,PID channel 28 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x110114+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110114+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110114+0x4)++0x3 line.long 0x0 "TSD2_PID28_CONFIG_2,PID channel 28 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110114+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110114+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110114+0x4)++0x3 line.long 0x0 "TSD2_PID28_CONFIG_2,PID channel 28 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110114+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110114+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110114+0x4)++0x3 line.long 0x0 "TSD2_PID28_CONFIG_2,PID channel 28 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x11011C)++0x3 line.long 0x0 "TSD2_PID29_CONFIG_1,PID channel 29 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x11011C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11011C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11011C+0x4)++0x3 line.long 0x0 "TSD2_PID29_CONFIG_2,PID channel 29 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x11011C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11011C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11011C+0x4)++0x3 line.long 0x0 "TSD2_PID29_CONFIG_2,PID channel 29 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11011C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11011C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11011C+0x4)++0x3 line.long 0x0 "TSD2_PID29_CONFIG_2,PID channel 29 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11011C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11011C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11011C+0x4)++0x3 line.long 0x0 "TSD2_PID29_CONFIG_2,PID channel 29 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x110124)++0x3 line.long 0x0 "TSD2_PID30_CONFIG_1,PID channel 30 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x110124+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110124+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110124+0x4)++0x3 line.long 0x0 "TSD2_PID30_CONFIG_2,PID channel 30 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x110124+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x110124+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110124+0x4)++0x3 line.long 0x0 "TSD2_PID30_CONFIG_2,PID channel 30 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110124+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110124+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x110124+0x4)++0x3 line.long 0x0 "TSD2_PID30_CONFIG_2,PID channel 30 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x110124+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x110124+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x110124+0x4)++0x3 line.long 0x0 "TSD2_PID30_CONFIG_2,PID channel 30 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif wgroup.long (ad:0xC0000000+0x11012C)++0x3 line.long 0x0 "TSD2_PID31_CONFIG_1,PID channel 31 configuration 1" bitfld.long 0x0 26. " SEARCH_AUD ,Enables searching of AUD in packets from the corresponding PID channel" "Disable,Enable" bitfld.long 0x0 21.--25. " AF_BUFFER ,Specifies in which buffer Adaptation Field (AF) shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x0 20. " STOP_AT_PSI_ERR ,Specifies whether PID channel shall be deactivated if PSI error is detected" "Activated,Not activated" textline " " bitfld.long 0x0 16. " DUPLICATE_IRQ_EN ,Interrupt enable bit for duplicate packet IRQ" "Disabled,Enabled" bitfld.long 0x0 13.--15. " NONEQUAL_BYTE_INDEX ,Specifies which byte shall be compared in non-equal mode during section filtering" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--12. " BUFFER_INDEX ,If the OFFSET_MODE is set to '0', BUFFER_INDEX specifies to which buffer the data of this PID channel shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x0 7. " OFFSET_MODE ,Specyfies the data of PID channel will be stored" "BUFFER_INDEX,BUFFER_INDEX+offset" if ((((per.l(ad:0xC0000000+0x11012C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11012C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11012C+0x4)++0x3 line.long 0x0 "TSD2_PID31_CONFIG_2,PID channel 31 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" textline " " elif ((((per.l(ad:0xC0000000+0x11012C+0x4))&0x8000)==0x0)&&(((per.l(ad:0xC0000000+0x11012C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11012C+0x4)++0x3 line.long 0x0 "TSD2_PID31_CONFIG_2,PID channel 31 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 13. " STORE_AF ,Indicate if adaptation field shall be stored" "Not stored,Stored" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" textline " " bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11012C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11012C+0x4))&0x10)==0x10)) wgroup.long (ad:0xC0000000+0x11012C+0x4)++0x3 line.long 0x0 "TSD2_PID31_CONFIG_2,PID channel 31 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 21.--24. " N_TARGET ,This bit group is used to configure section filter" ",1,2,,,,,,4,8,12,16,20,24,28,32" bitfld.long 0x0 16.--20. " TARGET_LENGTH ,Filter target length" ",1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,?..." textline " " bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" textline " " bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" textline " " bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" textline " " bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" elif ((((per.l(ad:0xC0000000+0x11012C+0x4))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x11012C+0x4))&0x10)==0x0)) wgroup.long (ad:0xC0000000+0x11012C+0x4)++0x3 line.long 0x0 "TSD2_PID31_CONFIG_2,PID channel 31 configuration 2" hexmask.long.byte 0x0 25.--31. 0x2000000 " PTR_TARGET ,Pointer to the first target in SF_target_RAM" bitfld.long 0x0 15. " STORE_COMPLETE_PACKET ,Indicate if TS packets header (4 bytes) and adaptation field shall be stored" "Payload,Complete Packet" bitfld.long 0x0 14. " PUS_IRQ_EN ,Payload Unit Start (PUS) interrupt enable" "Disabled,Enabled" textline " " bitfld.long 0x0 12. " AF_PL_IRQ_EN ,Interrupt enable bit for AF_PL_IRQ" "Disabled,Enabled" bitfld.long 0x0 11. " NEW_PCR_IRQ_EN ,Interrupt enable bit for NEW_PCR_IRQ" "Disabled,Enabled" bitfld.long 0x0 10. " CC_IRQ_EN ,Interrupt enableInterrupt enable bit for CONTINUITY_ERROR_IRQ bit for SECTION_END_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x0 9. " SECTION_END_IRQ_EN ,Interrupt enable bit for SECTION_END_IRQ" "Disable,Enable" bitfld.long 0x0 8. " PACKET_END_IRQ_EN ,Interrupt enable bit for PACKET_END_IRQ" "Disabled,Enabled" bitfld.long 0x0 6. " CC_CHECK ,Continuity Counter error check" "Don't ceck,Check" textline " " bitfld.long 0x0 5. " DUPLICATE_CHECK ,Duplicate packet check" "Don't ceck,Check" bitfld.long 0x0 4. " PES_PAYLOAD ,Specifies type of transport packet payload" "PSI,PES" bitfld.long 0x0 3. " EXTRACT_PCR ,Enable the extraction of PCR field from adaptation field" "Disabled,Enabled" textline " " bitfld.long 0x0 2. " PSI_CC_CHECK_MODE ,Specify the Continuity Counter (CC) Check Mode for PSI packets.(Mode0 -if CC_CHECK is enabled and section filter is active. Mode1- if CC_CHECK is enabled)" "Mode 0,Mode 1" bitfld.long 0x0 1. " AF_END_IRQ_EN ,Interrupt enable bit for AF_END_IRQ" "Disable,Enabled" endif tree.end tree.end width 23. tree "Odd/Even Key Registers" wgroup.long 0x10134++0x0F line.long 0x00 "TSD1_ODD_KEY0_UPPER,The upper 32 bit [63:32] of the odd descramble key 0 [63:0]" line.long 0x04 "TSD1_ODD_KEY0_LOWER,The lower 32 bit [31:0] of the odd descramble key 0 [63:0]" line.long 0x08 "TSD1_EVEN_KEY0_UPPER,The upper 32 bit [63:32] of the even descramble key 0 [63:0]" line.long 0x0C "TSD1_EVEN_KEY0_LOWER,The lower 32 bit [31:0] of the even descramble key 0[63:0]" wgroup.long 0x10144++0x0F line.long 0x00 "TSD1_ODD_KEY1_UPPER,The upper 32 bit [63:32] of the odd descramble key 1 [63:0]" line.long 0x04 "TSD1_ODD_KEY1_LOWER,The lower 32 bit [31:0] of the odd descramble key 1 [63:0]" line.long 0x08 "TSD1_EVEN_KEY1_UPPER,The upper 32 bit [63:32] of the even descramble key 1 [63:0]" line.long 0x0C "TSD1_EVEN_KEY1_LOWER,The lower 32 bit [31:0] of the even descramble key 1[63:0]" wgroup.long 0x10154++0x0F line.long 0x00 "TSD1_ODD_KEY2_UPPER,The upper 32 bit [63:32] of the odd descramble key 2 [63:0]" line.long 0x04 "TSD1_ODD_KEY2_LOWER,The lower 32 bit [31:0] of the odd descramble key 2 [63:0]" line.long 0x08 "TSD1_EVEN_KEY2_UPPER,The upper 32 bit [63:32] of the even descramble key 2 [63:0]" line.long 0x0C "TSD1_EVEN_KEY2_LOWER,The lower 32 bit [31:0] of the even descramble key 2[63:0]" wgroup.long 0x10164++0x0F line.long 0x00 "TSD1_ODD_KEY3_UPPER,The upper 32 bit [63:32] of the odd descramble key 3 [63:0]" line.long 0x04 "TSD1_ODD_KEY3_LOWER,The lower 32 bit [31:0] of the odd descramble key 3 [63:0]" line.long 0x08 "TSD1_EVEN_KEY3_UPPER,The upper 32 bit [63:32] of the even descramble key 3 [63:0]" line.long 0x0C "TSD1_EVEN_KEY3_LOWER,The lower 32 bit [31:0] of the even descramble key 3[63:0]" wgroup.long 0x10174++0x0F line.long 0x00 "TSD1_ODD_KEY4_UPPER,The upper 32 bit [63:32] of the odd descramble key 4 [63:0]" line.long 0x04 "TSD1_ODD_KEY4_LOWER,The lower 32 bit [31:0] of the odd descramble key 4 [63:0]" line.long 0x08 "TSD1_EVEN_KEY4_UPPER,The upper 32 bit [63:32] of the even descramble key 4 [63:0]" line.long 0x0C "TSD1_EVEN_KEY4_LOWER,The lower 32 bit [31:0] of the even descramble key 4[63:0]" wgroup.long 0x10184++0x0F line.long 0x00 "TSD1_ODD_KEY5_UPPER,The upper 32 bit [63:32] of the odd descramble key 5 [63:0]" line.long 0x04 "TSD1_ODD_KEY5_LOWER,The lower 32 bit [31:0] of the odd descramble key 5 [63:0]" line.long 0x08 "TSD1_EVEN_KEY5_UPPER,The upper 32 bit [63:32] of the even descramble key 5 [63:0]" line.long 0x0C "TSD1_EVEN_KEY5_LOWER,The lower 32 bit [31:0] of the even descramble key 5[63:0]" wgroup.long 0x10194++0x0F line.long 0x00 "TSD1_ODD_KEY6_UPPER,The upper 32 bit [63:32] of the odd descramble key 6 [63:0]" line.long 0x04 "TSD1_ODD_KEY6_LOWER,The lower 32 bit [31:0] of the odd descramble key 6 [63:0]" line.long 0x08 "TSD1_EVEN_KEY6_UPPER,The upper 32 bit [63:32] of the even descramble key 6 [63:0]" line.long 0x0C "TSD1_EVEN_KEY6_LOWER,The lower 32 bit [31:0] of the even descramble key 6[63:0]" wgroup.long 0x101A4++0x0F line.long 0x00 "TSD1_ODD_KEY7_UPPER,The upper 32 bit [63:32] of the odd descramble key 7 [63:0]" line.long 0x04 "TSD1_ODD_KEY7_LOWER,The lower 32 bit [31:0] of the odd descramble key 7 [63:0]" line.long 0x08 "TSD1_EVEN_KEY7_UPPER,The upper 32 bit [63:32] of the even descramble key 7 [63:0]" line.long 0x0C "TSD1_EVEN_KEY7_LOWER,The lower 32 bit [31:0] of the even descramble key 7[63:0]" wgroup.long 0x101B4++0x0F line.long 0x00 "TSD1_ODD_KEY8_UPPER,The upper 32 bit [63:32] of the odd descramble key 8 [63:0]" line.long 0x04 "TSD1_ODD_KEY8_LOWER,The lower 32 bit [31:0] of the odd descramble key 8 [63:0]" line.long 0x08 "TSD1_EVEN_KEY8_UPPER,The upper 32 bit [63:32] of the even descramble key 8 [63:0]" line.long 0x0C "TSD1_EVEN_KEY8_LOWER,The lower 32 bit [31:0] of the even descramble key 8[63:0]" wgroup.long 0x101C4++0x0F line.long 0x00 "TSD1_ODD_KEY9_UPPER,The upper 32 bit [63:32] of the odd descramble key 9 [63:0]" line.long 0x04 "TSD1_ODD_KEY9_LOWER,The lower 32 bit [31:0] of the odd descramble key 9 [63:0]" line.long 0x08 "TSD1_EVEN_KEY9_UPPER,The upper 32 bit [63:32] of the even descramble key 9 [63:0]" line.long 0x0C "TSD1_EVEN_KEY9_LOWER,The lower 32 bit [31:0] of the even descramble key 9[63:0]" wgroup.long 0x101D4++0x0F line.long 0x00 "TSD1_ODD_KEY10_UPPER,The upper 32 bit [63:32] of the odd descramble key 10 [63:0]" line.long 0x04 "TSD1_ODD_KEY10_LOWER,The lower 32 bit [31:0] of the odd descramble key 10 [63:0]" line.long 0x08 "TSD1_EVEN_KEY10_UPPER,The upper 32 bit [63:32] of the even descramble key 10 [63:0]" line.long 0x0C "TSD1_EVEN_KEY10_LOWER,The lower 32 bit [31:0] of the even descramble key 10[63:0]" wgroup.long 0x101E4++0x0F line.long 0x00 "TSD1_ODD_KEY11_UPPER,The upper 32 bit [63:32] of the odd descramble key 11 [63:0]" line.long 0x04 "TSD1_ODD_KEY11_LOWER,The lower 32 bit [31:0] of the odd descramble key 11 [63:0]" line.long 0x08 "TSD1_EVEN_KEY11_UPPER,The upper 32 bit [63:32] of the even descramble key 11 [63:0]" line.long 0x0C "TSD1_EVEN_KEY11_LOWER,The lower 32 bit [31:0] of the even descramble key 11[63:0]" wgroup.long 0x110134++0x0F line.long 0x00 "TSD2_ODD_KEY0_UPPER,The upper 32 bit [63:32] of the odd descramble key 0 [63:0]" line.long 0x04 "TSD2_ODD_KEY0_LOWER,The lower 32 bit [31:0] of the odd descramble key 0 [63:0]" line.long 0x08 "TSD2_EVEN_KEY0_UPPER,The upper 32 bit [63:32] of the even descramble key 0 [63:0]" line.long 0x0C "TSD2_EVEN_KEY0_LOWER,The lower 32 bit [31:0] of the even descramble key 0[63:0]" wgroup.long 0x110144++0x0F line.long 0x00 "TSD2_ODD_KEY1_UPPER,The upper 32 bit [63:32] of the odd descramble key 1 [63:0]" line.long 0x04 "TSD2_ODD_KEY1_LOWER,The lower 32 bit [31:0] of the odd descramble key 1 [63:0]" line.long 0x08 "TSD2_EVEN_KEY1_UPPER,The upper 32 bit [63:32] of the even descramble key 1 [63:0]" line.long 0x0C "TSD2_EVEN_KEY1_LOWER,The lower 32 bit [31:0] of the even descramble key 1[63:0]" wgroup.long 0x110154++0x0F line.long 0x00 "TSD2_ODD_KEY2_UPPER,The upper 32 bit [63:32] of the odd descramble key 2 [63:0]" line.long 0x04 "TSD2_ODD_KEY2_LOWER,The lower 32 bit [31:0] of the odd descramble key 2 [63:0]" line.long 0x08 "TSD2_EVEN_KEY2_UPPER,The upper 32 bit [63:32] of the even descramble key 2 [63:0]" line.long 0x0C "TSD2_EVEN_KEY2_LOWER,The lower 32 bit [31:0] of the even descramble key 2[63:0]" wgroup.long 0x110164++0x0F line.long 0x00 "TSD2_ODD_KEY3_UPPER,The upper 32 bit [63:32] of the odd descramble key 3 [63:0]" line.long 0x04 "TSD2_ODD_KEY3_LOWER,The lower 32 bit [31:0] of the odd descramble key 3 [63:0]" line.long 0x08 "TSD2_EVEN_KEY3_UPPER,The upper 32 bit [63:32] of the even descramble key 3 [63:0]" line.long 0x0C "TSD2_EVEN_KEY3_LOWER,The lower 32 bit [31:0] of the even descramble key 3[63:0]" wgroup.long 0x110174++0x0F line.long 0x00 "TSD2_ODD_KEY4_UPPER,The upper 32 bit [63:32] of the odd descramble key 4 [63:0]" line.long 0x04 "TSD2_ODD_KEY4_LOWER,The lower 32 bit [31:0] of the odd descramble key 4 [63:0]" line.long 0x08 "TSD2_EVEN_KEY4_UPPER,The upper 32 bit [63:32] of the even descramble key 4 [63:0]" line.long 0x0C "TSD2_EVEN_KEY4_LOWER,The lower 32 bit [31:0] of the even descramble key 4[63:0]" wgroup.long 0x110184++0x0F line.long 0x00 "TSD2_ODD_KEY5_UPPER,The upper 32 bit [63:32] of the odd descramble key 5 [63:0]" line.long 0x04 "TSD2_ODD_KEY5_LOWER,The lower 32 bit [31:0] of the odd descramble key 5 [63:0]" line.long 0x08 "TSD2_EVEN_KEY5_UPPER,The upper 32 bit [63:32] of the even descramble key 5 [63:0]" line.long 0x0C "TSD2_EVEN_KEY5_LOWER,The lower 32 bit [31:0] of the even descramble key 5[63:0]" wgroup.long 0x110194++0x0F line.long 0x00 "TSD2_ODD_KEY6_UPPER,The upper 32 bit [63:32] of the odd descramble key 6 [63:0]" line.long 0x04 "TSD2_ODD_KEY6_LOWER,The lower 32 bit [31:0] of the odd descramble key 6 [63:0]" line.long 0x08 "TSD2_EVEN_KEY6_UPPER,The upper 32 bit [63:32] of the even descramble key 6 [63:0]" line.long 0x0C "TSD2_EVEN_KEY6_LOWER,The lower 32 bit [31:0] of the even descramble key 6[63:0]" wgroup.long 0x1101A4++0x0F line.long 0x00 "TSD2_ODD_KEY7_UPPER,The upper 32 bit [63:32] of the odd descramble key 7 [63:0]" line.long 0x04 "TSD2_ODD_KEY7_LOWER,The lower 32 bit [31:0] of the odd descramble key 7 [63:0]" line.long 0x08 "TSD2_EVEN_KEY7_UPPER,The upper 32 bit [63:32] of the even descramble key 7 [63:0]" line.long 0x0C "TSD2_EVEN_KEY7_LOWER,The lower 32 bit [31:0] of the even descramble key 7[63:0]" wgroup.long 0x1101B4++0x0F line.long 0x00 "TSD2_ODD_KEY8_UPPER,The upper 32 bit [63:32] of the odd descramble key 8 [63:0]" line.long 0x04 "TSD2_ODD_KEY8_LOWER,The lower 32 bit [31:0] of the odd descramble key 8 [63:0]" line.long 0x08 "TSD2_EVEN_KEY8_UPPER,The upper 32 bit [63:32] of the even descramble key 8 [63:0]" line.long 0x0C "TSD2_EVEN_KEY8_LOWER,The lower 32 bit [31:0] of the even descramble key 8[63:0]" wgroup.long 0x1101C4++0x0F line.long 0x00 "TSD2_ODD_KEY9_UPPER,The upper 32 bit [63:32] of the odd descramble key 9 [63:0]" line.long 0x04 "TSD2_ODD_KEY9_LOWER,The lower 32 bit [31:0] of the odd descramble key 9 [63:0]" line.long 0x08 "TSD2_EVEN_KEY9_UPPER,The upper 32 bit [63:32] of the even descramble key 9 [63:0]" line.long 0x0C "TSD2_EVEN_KEY9_LOWER,The lower 32 bit [31:0] of the even descramble key 9[63:0]" wgroup.long 0x1101D4++0x0F line.long 0x00 "TSD2_ODD_KEY10_UPPER,The upper 32 bit [63:32] of the odd descramble key 10 [63:0]" line.long 0x04 "TSD2_ODD_KEY10_LOWER,The lower 32 bit [31:0] of the odd descramble key 10 [63:0]" line.long 0x08 "TSD2_EVEN_KEY10_UPPER,The upper 32 bit [63:32] of the even descramble key 10 [63:0]" line.long 0x0C "TSD2_EVEN_KEY10_LOWER,The lower 32 bit [31:0] of the even descramble key 10[63:0]" wgroup.long 0x1101E4++0x0F line.long 0x00 "TSD2_ODD_KEY11_UPPER,The upper 32 bit [63:32] of the odd descramble key 11 [63:0]" line.long 0x04 "TSD2_ODD_KEY11_LOWER,The lower 32 bit [31:0] of the odd descramble key 11 [63:0]" line.long 0x08 "TSD2_EVEN_KEY11_UPPER,The upper 32 bit [63:32] of the even descramble key 11 [63:0]" line.long 0x0C "TSD2_EVEN_KEY11_LOWER,The lower 32 bit [31:0] of the even descramble key 11[63:0]" tree.end tree "MULTI2" wgroup.long 0x101F4++0x07 line.long 0x0 "TSD2_M2IV_UPPER,The upper 32 bit [63:32] of Multi2 Initial Vector [63:0]" line.long 0x4 "TSD2_M2IV_LOWER,The lower 32 bit [31:0] of Multi2 Initial Vector [63:0]" wgroup.long 0x1101F4++0x07 line.long 0x0 "TSD1_M2IV_UPPER,The upper 32 bit [63:32] of Multi2 Initial Vector [63:0]" line.long 0x4 "TSD1_M2IV_LOWER,The lower 32 bit [31:0] of Multi2 Initial Vector [63:0]" group.long 0x400280++0x1F line.long 0x00 "TSD_M2SK_255_224,MULTI2 system key bits [255:224]" line.long 0x04 "TSD_M2SK_223_192,MULTI2 system key bits [223:192]" line.long 0x08 "TSD_M2SK_191_160,MULTI2 system key bits [191:160]" line.long 0x0C "TSD_M2SK_159_128,MULTI2 system key bits [159:128]" line.long 0x10 "TSD_M2SK_127_96,MULTI2 system key bits [127:96]" line.long 0x14 "TSD_M2SK_95_64,MULTI2 system key bits [95:64]" line.long 0x18 "TSD_M2SK_63_32,MULTI2 system key bits [63:32]" line.long 0x1C "TSD_M2SK_31_0,MULTI2 system key bits [31:0]" tree.end textline " " width 29. group.long 0x88++0x07 line.long 0x04 "TSD1_RECORD_MODE,Record mode enable" bitfld.long 0x04 0. " VALUE , Record mode enable on TSD1" "Disabled,Enabled" line.long 0x00 "TSD1_READ_SIGNAL_DISTANCE,Distance between read requests" hexmask.long.byte 0x00 0.--7. 1. " VALUE ,Number of clock cycles between two read requests sent to TS packet input buffer by PID filter" group.long 0xCC++0x17 line.long 0x00 "TSD1_PACKET_COUNTER,Number of packets received at packet parser" line.long 0x04 "TSD1_VALID_PACKET_COUNTER,Number of valid packets received" line.long 0x08 "TSD1_INPUT_PACKET_COUNTER,Number of packets received at packet buffer" line.long 0x0C "TSD1_FILTER_PID_COUNTER,Number of packets received at FSM of packet parser" line.long 0x10 "TSD1_FOUND_PL_COUNTER,Number of packets with payload found at FSM of packet parser" line.long 0x14 "TSD1_PACKET_PROCSSED_COUNTER,Number of packets processed by packet parser" textline " " group.long 0x100088++0x07 line.long 0x04 "TSD2_RECORD_MODE,Record mode enable" bitfld.long 0x04 0. " VALUE , Record mode enable on TSD2" "Disabled,Enabled" line.long 0x00 "TSD2_READ_SIGNAL_DISTANCE,Distance between read requests" hexmask.long.byte 0x00 0.--7. 1. " VALUE ,Number of clock cycles between two read requests sent to TS packet input buffer by PID filter" group.long 0x1000CC++0x17 line.long 0x00 "TSD2_PACKET_COUNTER,Number of packets received at packet parser" line.long 0x04 "TSD2_VALID_PACKET_COUNTER,Number of valid packets received" line.long 0x08 "TSD2_INPUT_PACKET_COUNTER,Number of packets received at packet buffer" line.long 0x0C "TSD2_FILTER_PID_COUNTER,Number of packets received at FSM of packet parser" line.long 0x10 "TSD2_FOUND_PL_COUNTER,Number of packets with payload found at FSM of packet parser" line.long 0x14 "TSD2_PACKET_PROCSSED_COUNTER,Number of packets processed by packet parser" group.long 0x1000E4++0x03 line.long 0x00 "TSD2_PACKET_PROCSSED_COUNTER,Number of packets processed by packet parser" tree "PID Channel Activation Registers" tree "TSD1" group.long 0x0++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_0,Activation register for channel 0" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x4++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_1,Activation register for channel 1" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x8++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_2,Activation register for channel 2" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0xC++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_3,Activation register for channel 3" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x10++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_4,Activation register for channel 4" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x14++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_5,Activation register for channel 5" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x18++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_6,Activation register for channel 6" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x1C++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_7,Activation register for channel 7" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x20++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_8,Activation register for channel 8" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x24++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_9,Activation register for channel 9" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x28++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_10,Activation register for channel 10" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x2C++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_11,Activation register for channel 11" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x30++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_12,Activation register for channel 12" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x34++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_13,Activation register for channel 13" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x38++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_14,Activation register for channel 14" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x3C++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_15,Activation register for channel 15" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x40++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_16,Activation register for channel 16" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x44++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_17,Activation register for channel 17" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x48++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_18,Activation register for channel 18" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x4C++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_19,Activation register for channel 19" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x50++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_20,Activation register for channel 20" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x54++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_21,Activation register for channel 21" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x58++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_22,Activation register for channel 22" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x5C++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_23,Activation register for channel 23" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x60++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_24,Activation register for channel 24" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x64++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_25,Activation register for channel 25" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x68++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_26,Activation register for channel 26" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x6C++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_27,Activation register for channel 27" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x70++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_28,Activation register for channel 28" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x74++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_29,Activation register for channel 29" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x78++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_30,Activation register for channel 30" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x7C++0x03 line.long 0x00 "TSD1_PID_CHANNEL_ACTIVE_31,Activation register for channel 31" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" tree.end tree "TSD2" group.long 0x100000++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_0,Activation register for channel 0" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100004++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_1,Activation register for channel 1" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100008++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_2,Activation register for channel 2" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x10000C++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_3,Activation register for channel 3" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100010++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_4,Activation register for channel 4" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100014++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_5,Activation register for channel 5" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100018++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_6,Activation register for channel 6" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x10001C++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_7,Activation register for channel 7" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100020++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_8,Activation register for channel 8" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100024++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_9,Activation register for channel 9" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100028++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_10,Activation register for channel 10" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x10002C++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_11,Activation register for channel 11" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100030++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_12,Activation register for channel 12" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100034++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_13,Activation register for channel 13" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100038++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_14,Activation register for channel 14" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x10003C++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_15,Activation register for channel 15" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100040++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_16,Activation register for channel 16" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100044++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_17,Activation register for channel 17" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100048++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_18,Activation register for channel 18" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x10004C++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_19,Activation register for channel 19" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100050++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_20,Activation register for channel 20" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100054++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_21,Activation register for channel 21" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100058++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_22,Activation register for channel 22" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x10005C++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_23,Activation register for channel 23" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100060++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_24,Activation register for channel 24" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100064++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_25,Activation register for channel 25" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100068++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_26,Activation register for channel 26" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x10006C++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_27,Activation register for channel 27" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100070++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_28,Activation register for channel 28" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100074++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_29,Activation register for channel 29" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x100078++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_30,Activation register for channel 30" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" group.long 0x10007C++0x03 line.long 0x00 "TSD2_PID_CHANNEL_ACTIVE_31,Activation register for channel 31" bitfld.long 0x00 1. " ENABLE ,Enable the corresponding PID channel" "Disabled,Enabled" bitfld.long 0x00 0. " FIRST_PACKET_FLAG ,Upcoming packet is or not the first packet to be received" "Not first,First" tree.end tree.end textline " " group.long 0x80++0x3 line.long 0x0 "TSD1_PID_CHANNEL_ACTIVE_ALL,Activate PID channels" bitfld.long 0x0 31. " PID31 ,Activate PID channel 31" "Not activated,Activated" bitfld.long 0x0 30. " PID30 ,Activate PID channel 30" "Not activated,Activated" bitfld.long 0x0 29. " PID29 ,Activate PID channel 29" "Not activated,Activated" textline " " bitfld.long 0x0 28. " PID28 ,Activate PID channel 28" "Not activated,Activated" bitfld.long 0x0 27. " PID27 ,Activate PID channel 27" "Not activated,Activated" bitfld.long 0x0 26. " PID26 ,Activate PID channel 26" "Not activated,Activated" textline " " bitfld.long 0x0 25. " PID25 ,Activate PID channel 25" "Not activated,Activated" bitfld.long 0x0 24. " PID24 ,Activate PID channel 24" "Not activated,Activated" bitfld.long 0x0 23. " PID23 ,Activate PID channel 23" "Not activated,Activated" textline " " bitfld.long 0x0 22. " PID22 ,Activate PID channel 22" "Not activated,Activated" bitfld.long 0x0 21. " PID21 ,Activate PID channel 21" "Not activated,Activated" bitfld.long 0x0 20. " PID20 ,Activate PID channel 20" "Not activated,Activated" textline " " bitfld.long 0x0 19. " PID19 ,Activate PID channel 19" "Not activated,Activated" bitfld.long 0x0 18. " PID18 ,Activate PID channel 18" "Not activated,Activated" bitfld.long 0x0 17. " PID17 ,Activate PID channel 17" "Not activated,Activated" textline " " bitfld.long 0x0 16. " PID16 ,Activate PID channel 16" "Not activated,Activated" bitfld.long 0x0 15. " PID15 ,Activate PID channel 15" "Not activated,Activated" bitfld.long 0x0 14. " PID14 ,Activate PID channel 14" "Not activated,Activated" textline " " bitfld.long 0x0 13. " PID13 ,Activate PID channel 13" "Not activated,Activated" bitfld.long 0x0 12. " PID12 ,Activate PID channel 12" "Not activated,Activated" bitfld.long 0x0 11. " PID11 ,Activate PID channel 11" "Not activated,Activated" textline " " bitfld.long 0x0 10. " PID10 ,Activate PID channel 10" "Not activated,Activated" bitfld.long 0x0 9. " PID9 ,Activate PID channel 9" "Not activated,Activated" bitfld.long 0x0 8. " PID8 ,Activate PID channel 8" "Not activated,Activated" textline " " bitfld.long 0x0 7. " PID7 ,Activate PID channel 7" "Not activated,Activated" bitfld.long 0x0 6. " PID6 ,Activate PID channel 6" "Not activated,Activated" bitfld.long 0x0 5. " PID5 ,Activate PID channel 5" "Not activated,Activated" textline " " bitfld.long 0x0 4. " PID4 ,Activate PID channel 4" "Not activated,Activated" bitfld.long 0x0 3. " PID3 ,Activate PID channel 3" "Not activated,Activated" bitfld.long 0x0 2. " PID2 ,Activate PID channel 2" "Not activated,Activated" textline " " bitfld.long 0x0 1. " PID1 ,Activate PID channel 1" "Not activated,Activated" bitfld.long 0x0 0. " PID0 ,Activate PID channel 0" "Not activated,Activated" group.long 0x100080++0x3 line.long 0x0 "TSD2_PID_CHANNEL_ACTIVE_ALL,Activate PID channels" bitfld.long 0x0 31. " PID31 ,Activate PID channel 31" "Not activated,Activated" bitfld.long 0x0 30. " PID30 ,Activate PID channel 30" "Not activated,Activated" bitfld.long 0x0 29. " PID29 ,Activate PID channel 29" "Not activated,Activated" textline " " bitfld.long 0x0 28. " PID28 ,Activate PID channel 28" "Not activated,Activated" bitfld.long 0x0 27. " PID27 ,Activate PID channel 27" "Not activated,Activated" bitfld.long 0x0 26. " PID26 ,Activate PID channel 26" "Not activated,Activated" textline " " bitfld.long 0x0 25. " PID25 ,Activate PID channel 25" "Not activated,Activated" bitfld.long 0x0 24. " PID24 ,Activate PID channel 24" "Not activated,Activated" bitfld.long 0x0 23. " PID23 ,Activate PID channel 23" "Not activated,Activated" textline " " bitfld.long 0x0 22. " PID22 ,Activate PID channel 22" "Not activated,Activated" bitfld.long 0x0 21. " PID21 ,Activate PID channel 21" "Not activated,Activated" bitfld.long 0x0 20. " PID20 ,Activate PID channel 20" "Not activated,Activated" textline " " bitfld.long 0x0 19. " PID19 ,Activate PID channel 19" "Not activated,Activated" bitfld.long 0x0 18. " PID18 ,Activate PID channel 18" "Not activated,Activated" bitfld.long 0x0 17. " PID17 ,Activate PID channel 17" "Not activated,Activated" textline " " bitfld.long 0x0 16. " PID16 ,Activate PID channel 16" "Not activated,Activated" bitfld.long 0x0 15. " PID15 ,Activate PID channel 15" "Not activated,Activated" bitfld.long 0x0 14. " PID14 ,Activate PID channel 14" "Not activated,Activated" textline " " bitfld.long 0x0 13. " PID13 ,Activate PID channel 13" "Not activated,Activated" bitfld.long 0x0 12. " PID12 ,Activate PID channel 12" "Not activated,Activated" bitfld.long 0x0 11. " PID11 ,Activate PID channel 11" "Not activated,Activated" textline " " bitfld.long 0x0 10. " PID10 ,Activate PID channel 10" "Not activated,Activated" bitfld.long 0x0 9. " PID9 ,Activate PID channel 9" "Not activated,Activated" bitfld.long 0x0 8. " PID8 ,Activate PID channel 8" "Not activated,Activated" textline " " bitfld.long 0x0 7. " PID7 ,Activate PID channel 7" "Not activated,Activated" bitfld.long 0x0 6. " PID6 ,Activate PID channel 6" "Not activated,Activated" bitfld.long 0x0 5. " PID5 ,Activate PID channel 5" "Not activated,Activated" textline " " bitfld.long 0x0 4. " PID4 ,Activate PID channel 4" "Not activated,Activated" bitfld.long 0x0 3. " PID3 ,Activate PID channel 3" "Not activated,Activated" bitfld.long 0x0 2. " PID2 ,Activate PID channel 2" "Not activated,Activated" textline " " bitfld.long 0x0 1. " PID1 ,Activate PID channel 1" "Not activated,Activated" bitfld.long 0x0 0. " PID0 ,Activate PID channel 0" "Not activated,Activated" textline "" group.long 0x400214++0x03 line.long 0x00 "TSD_STATUS,TDS status register(activePID value match etc.)" bitfld.long 0x00 10. " Active ,This bit indicates if any packet is being processed by a TSD" "No,Yes" bitfld.long 0x00 9. " PidMatchValid ,This bit indicates if the PidMatch bit in this register is valid or not" "Invalid,Valid" textline " " bitfld.long 0x00 8. " PIDMATCH ,indicates if the PID of the incoming packet matches any PID configured" "No,Yes" bitfld.long 0x00 5.--6. " INDEX ,indicates which TSD is currently active and to which TSD the following PidIndex belongs to" "0,1,2,3" textline " " bitfld.long 0x00 0.--4. " PIDINDEX ,Indicates which PID channel is under processing" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" sif (cpu()=="MB86R11F") group.long 0xC0400200++0x07 line.long 0x00 "TSD_CURRENT_STC_LOWER,Current STC register bits[31:0]" hexmask.long.tbyte 0x00 9.--31. 1. " BASELOWER ,The lower 23 bits of current STC base" hexmask.long.word 0x00 0.--8. 1. " EXTENSION ,The current STC extension" line.long 0x04 " TSD_CURRENT_STC_UPPER,Current STC register bits[41:32]" hexmask.long.word 0x04 0.--9. 1. " BASEUPPER ,The upper 10 bits of current STC base" endif rgroup.long 0x400208++0x07 line.long 0x00 "TSD_PCR_LOWER,TSD_PCR_LOWER" hexmask.long.tbyte 0x00 9.--31. 1. " BASELOWER ,The lower 23 bits of PCR base found in the packet" hexmask.long.word 0x00 0.--8. 1. " EXTENSION ,The PCR extension found in the packet" line.long 0x04 "TSD_PCR_UPPER,Upper 10 bits of PCR base" hexmask.long.word 0x04 0.--9. 1. " BASEUPPER ,The upper 10 bits of PCR base" sif (cpu()=="MB86R11F") group.long 0xC0400210++0x03 line.long 0x00 "TSD_LOAD_PCR,Specify if PCR value shall be loaded to current STC register" bitfld.long 0x00 0. " VALUE ,Load value" "No load,Load" endif rgroup.long 0x98++0x07 line.long 0x00 "TSD1_PACKET_STC_LOWER,Lower STC packet register" hexmask.long.tbyte 0x00 9.--31. 1. " BASE ,The lower 23 bits of STC base" hexmask.long.word 0x00 0.--8. 1. " EXTENSION ,The STC extension which was sampled as the packet was received" line.long 0x04 "TSD1_PACKET_STC_UPPER,Upper STC packet register" hexmask.long.word 0x04 0.--9. 1. " BASE ,The upper 10 bits of STC base" rgroup.long 0x20000++0x3 line.long 0x0 "TSD1_PACKET0_STC_LOWER,STC for packet 0" hexmask.long.tbyte 0x00 9.--31. 1. " BASE ,The lower 23 bits of STC base which is sampled as packet 0 is received" hexmask.long.word 0x00 0.--8. 1. " EXTENSION ,The STC extension which is sampled as packet 0 is received" rgroup.long 0x24004++0x03 line.long 0x00 "TSD1_PACKET0_STC_UPPER,Upper 10 bits of STC packet 0" hexmask.long.word 0x00 0.--9. 1. " BASE ,The upper 10 bits of STC base which is sampled as packet 0 is received" rgroup.long 0x200C0++0x3 line.long 0x0 "TSD1_PACKET1_STC_LOWER,STC for packet 1" hexmask.long.tbyte 0x00 9.--31. 1. " BASE ,The lower 23 bits of STC base which is sampled as packet 1 is received" hexmask.long.word 0x00 0.--8. 1. " EXTENSION ,The STC extension which is sampled as packet 1 is received" rgroup.long 0x24008++0x03 line.long 0x00 "TSD1_PACKET1_STC_UPPER,Upper 10 bits of STC packet 1" hexmask.long.word 0x00 0.--9. 1. " BASE ,The upper 10 bits of STC base which is sampled as packet 1 is received" rgroup.long 0x20180++0x3 line.long 0x0 "TSD1_PACKET2_STC_LOWER,STC for packet 2" hexmask.long.tbyte 0x00 9.--31. 1. " BASE ,The lower 23 bits of STC base which is sampled as packet 2 is received" hexmask.long.word 0x00 0.--8. 1. " EXTENSION ,The STC extension which is sampled as packet 2 is received" rgroup.long 0x2400C++0x03 line.long 0x00 "TSD1_PACKET2_STC_UPPER,Upper 10 bits of STC packet 2" hexmask.long.word 0x00 0.--9. 1. " BASE ,The upper 10 bits of STC base which is sampled as packet 2 is received" rgroup.long 0x20240++0x3 line.long 0x0 "TSD1_PACKET3_STC_LOWER,STC for packet 3" hexmask.long.tbyte 0x00 9.--31. 1. " BASE ,The lower 23 bits of STC base which is sampled as packet 3 is received" hexmask.long.word 0x00 0.--8. 1. " EXTENSION ,The STC extension which is sampled as packet 3 is received" rgroup.long 0x2400C++0x03 line.long 0x00 "TSD1_PACKET3_STC_UPPER,Upper 10 bits of STC packet 3" hexmask.long.word 0x00 0.--9. 1. " BASE ,The upper 10 bits of STC base which is sampled as packet 3 is received" group.long 0x94++0x03 line.long 0x00 "TSD1_PACKET_STC_MODE,Packet STC mode" bitfld.long 0x00 0. " FOR_ALL_PACKET ,Specifies when the registers TSD1_PACKET_STC_LOWER/UPPER shall be updated" "With PCR,All" rgroup.long 0x100098++0x7 line.long 0x00 "TSD2_PACKET_STC_LOWER,Lower STC packet register" hexmask.long.tbyte 0x00 9.--31. 1. " BASE ,The lower 23 bits of STC base" hexmask.long.word 0x00 0.--8. 1. " EXTENSION ,The STC extension which was sampled as the packet was received" line.long 0x04 "TSD2_PACKET_STC_UPPER,Upper STC packet register" hexmask.long.word 0x04 0.--9. 1. " BASE ,The upper 10 bits of STC base" rgroup.long 0x120000++0x3 line.long 0x0 "TSD2_PACKET0_STC_LOWER,STC for packet 0" hexmask.long.tbyte 0x00 9.--31. 1. " BASE ,The lower 23 bits of STC base which is sampled as packet 0 is received" hexmask.long.word 0x00 0.--8. 1. " EXTENSION ,The STC extension which is sampled as packet 0 is received" rgroup.long 0x124004++0x03 line.long 0x00 "TSD2_PACKET0_STC_UPPER,Upper 10 bits of STC packet 0" hexmask.long.word 0x00 0.--9. 1. " BASE ,The upper 10 bits of STC base which is sampled as packet 0 is received" rgroup.long 0x1200C0++0x3 line.long 0x0 "TSD2_PACKET1_STC_LOWER,STC for packet 1" hexmask.long.tbyte 0x00 9.--31. 1. " BASE ,The lower 23 bits of STC base which is sampled as packet 1 is received" hexmask.long.word 0x00 0.--8. 1. " EXTENSION ,The STC extension which is sampled as packet 1 is received" rgroup.long 0x124008++0x03 line.long 0x00 "TSD2_PACKET1_STC_UPPER,Upper 10 bits of STC packet 1" hexmask.long.word 0x00 0.--9. 1. " BASE ,The upper 10 bits of STC base which is sampled as packet 1 is received" rgroup.long 0x120180++0x3 line.long 0x0 "TSD2_PACKET2_STC_LOWER,STC for packet 2" hexmask.long.tbyte 0x00 9.--31. 1. " BASE ,The lower 23 bits of STC base which is sampled as packet 2 is received" hexmask.long.word 0x00 0.--8. 1. " EXTENSION ,The STC extension which is sampled as packet 2 is received" rgroup.long 0x12400C++0x03 line.long 0x00 "TSD2_PACKET2_STC_UPPER,Upper 10 bits of STC packet 2" hexmask.long.word 0x00 0.--9. 1. " BASE ,The upper 10 bits of STC base which is sampled as packet 2 is received" rgroup.long 0x120240++0x3 line.long 0x0 "TSD2_PACKET3_STC_LOWER,STC for packet 3" hexmask.long.tbyte 0x00 9.--31. 1. " BASE ,The lower 23 bits of STC base which is sampled as packet 3 is received" hexmask.long.word 0x00 0.--8. 1. " EXTENSION ,The STC extension which is sampled as packet 3 is received" rgroup.long 0x12400C++0x03 line.long 0x00 "TSD2_PACKET3_STC_UPPER,Upper 10 bits of STC packet 3" hexmask.long.word 0x00 0.--9. 1. " BASE ,The upper 10 bits of STC base which is sampled as packet 3 is received" group.long 0x100094++0x03 line.long 0x00 "TSD2_PACKET_STC_MODE,Packet STC mode" bitfld.long 0x00 0. " FOR_ALL_PACKET ,Specifies when the registers TSD2_PACKET_STC_LOWER/UPPER shall be updated" "With PCR,All" tree.end tree "Section Filter" width 22. tree "Control Registers" tree "TSD1" group.long 0x30000++0x03 line.long 0x00 "TSD1_SB_CTRL_0,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30004++0x03 line.long 0x00 "TSD1_SB_CTRL_1,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30008++0x03 line.long 0x00 "TSD1_SB_CTRL_2,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x3000C++0x03 line.long 0x00 "TSD1_SB_CTRL_3,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30010++0x03 line.long 0x00 "TSD1_SB_CTRL_4,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30014++0x03 line.long 0x00 "TSD1_SB_CTRL_5,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30018++0x03 line.long 0x00 "TSD1_SB_CTRL_6,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x3001C++0x03 line.long 0x00 "TSD1_SB_CTRL_7,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30020++0x03 line.long 0x00 "TSD1_SB_CTRL_8,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30024++0x03 line.long 0x00 "TSD1_SB_CTRL_9,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30028++0x03 line.long 0x00 "TSD1_SB_CTRL_10,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x3002C++0x03 line.long 0x00 "TSD1_SB_CTRL_11,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30030++0x03 line.long 0x00 "TSD1_SB_CTRL_12,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30034++0x03 line.long 0x00 "TSD1_SB_CTRL_13,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30038++0x03 line.long 0x00 "TSD1_SB_CTRL_14,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x3003C++0x03 line.long 0x00 "TSD1_SB_CTRL_15,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30040++0x03 line.long 0x00 "TSD1_SB_CTRL_16,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30044++0x03 line.long 0x00 "TSD1_SB_CTRL_17,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30048++0x03 line.long 0x00 "TSD1_SB_CTRL_18,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x3004C++0x03 line.long 0x00 "TSD1_SB_CTRL_19,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30050++0x03 line.long 0x00 "TSD1_SB_CTRL_20,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30054++0x03 line.long 0x00 "TSD1_SB_CTRL_21,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30058++0x03 line.long 0x00 "TSD1_SB_CTRL_22,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x3005C++0x03 line.long 0x00 "TSD1_SB_CTRL_23,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30060++0x03 line.long 0x00 "TSD1_SB_CTRL_24,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30064++0x03 line.long 0x00 "TSD1_SB_CTRL_25,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30068++0x03 line.long 0x00 "TSD1_SB_CTRL_26,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x3006C++0x03 line.long 0x00 "TSD1_SB_CTRL_27,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30070++0x03 line.long 0x00 "TSD1_SB_CTRL_28,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30074++0x03 line.long 0x00 "TSD1_SB_CTRL_29,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30078++0x03 line.long 0x00 "TSD1_SB_CTRL_30,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x3007C++0x03 line.long 0x00 "TSD1_SB_CTRL_31,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " Residue_Cnt ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x30104++0x7 "Debug Registers" line.long 0x0 "TSD1_SB_STARTED_CNT,Indicates how many times the section buffer FSM is started" line.long 0x4 "TSD1_SB_FINISHED_CNT,Indicates how many times the section buffer FSM has finished successfully" tree.end tree "TSD2" group.long 0x130000++0x03 line.long 0x00 "TSD2_SB_CTRL_0,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130004++0x03 line.long 0x00 "TSD2_SB_CTRL_1,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130008++0x03 line.long 0x00 "TSD2_SB_CTRL_2,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x13000C++0x03 line.long 0x00 "TSD2_SB_CTRL_3,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130010++0x03 line.long 0x00 "TSD2_SB_CTRL_4,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130014++0x03 line.long 0x00 "TSD2_SB_CTRL_5,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130018++0x03 line.long 0x00 "TSD2_SB_CTRL_6,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x13001C++0x03 line.long 0x00 "TSD2_SB_CTRL_7,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130020++0x03 line.long 0x00 "TSD2_SB_CTRL_8,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130024++0x03 line.long 0x00 "TSD2_SB_CTRL_9,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130028++0x03 line.long 0x00 "TSD2_SB_CTRL_10,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x13002C++0x03 line.long 0x00 "TSD2_SB_CTRL_11,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130030++0x03 line.long 0x00 "TSD2_SB_CTRL_12,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130034++0x03 line.long 0x00 "TSD2_SB_CTRL_13,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130038++0x03 line.long 0x00 "TSD2_SB_CTRL_14,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x13003C++0x03 line.long 0x00 "TSD2_SB_CTRL_15,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130040++0x03 line.long 0x00 "TSD2_SB_CTRL_16,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130044++0x03 line.long 0x00 "TSD2_SB_CTRL_17,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130048++0x03 line.long 0x00 "TSD2_SB_CTRL_18,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x13004C++0x03 line.long 0x00 "TSD2_SB_CTRL_19,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130050++0x03 line.long 0x00 "TSD2_SB_CTRL_20,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130054++0x03 line.long 0x00 "TSD2_SB_CTRL_21,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130058++0x03 line.long 0x00 "TSD2_SB_CTRL_22,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x13005C++0x03 line.long 0x00 "TSD2_SB_CTRL_23,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130060++0x03 line.long 0x00 "TSD2_SB_CTRL_24,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130064++0x03 line.long 0x00 "TSD2_SB_CTRL_25,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130068++0x03 line.long 0x00 "TSD2_SB_CTRL_26,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x13006C++0x03 line.long 0x00 "TSD2_SB_CTRL_27,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130070++0x03 line.long 0x00 "TSD2_SB_CTRL_28,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130074++0x03 line.long 0x00 "TSD2_SB_CTRL_29,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130078++0x03 line.long 0x00 "TSD2_SB_CTRL_30,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x13007C++0x03 line.long 0x00 "TSD2_SB_CTRL_31,Section header buffer control" bitfld.long 0x00 26.--31. " WR_PTR ,Write pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 20.--25. " RD_PTR ,Read pointer of the section header buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" hexmask.long.word 0x00 8.--19. 1. " RESIDUE_CNT ,The number of remaining data bytes of the corresponding target" textline " " bitfld.long 0x00 6.--7. " PADDING_CNT ,The number of padding bytes needed for the current section" "0,1,2,3" bitfld.long 0x00 5. " FILTER_MATCH ,Indicates if the current section matches any filter target" "Not matched,Matched" bitfld.long 0x00 0.--4. " FILTER_INDEX ,The index of the matched filter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x130104++0x7 "Debug Registers" line.long 0x0 "TSD2_SB_STARTED_CNT,Indicates how many times the section buffer FSM is started" line.long 0x4 "TSD2_SB_FINISHED_CNT,Indicates how many times the section buffer FSM has finished successfully" tree.end tree.end width 17. tree "Calculated Values" tree "TSD1" group.long 0x30080++0x03 line.long 0x00 "TSD1_SF_CRC_0,CRC value 0 calculated for the section bytes" group.long 0x30084++0x03 line.long 0x00 "TSD1_SF_CRC_1,CRC value 1 calculated for the section bytes" group.long 0x30088++0x03 line.long 0x00 "TSD1_SF_CRC_2,CRC value 2 calculated for the section bytes" group.long 0x3008C++0x03 line.long 0x00 "TSD1_SF_CRC_3,CRC value 3 calculated for the section bytes" group.long 0x30090++0x03 line.long 0x00 "TSD1_SF_CRC_4,CRC value 4 calculated for the section bytes" group.long 0x30094++0x03 line.long 0x00 "TSD1_SF_CRC_5,CRC value 5 calculated for the section bytes" group.long 0x30098++0x03 line.long 0x00 "TSD1_SF_CRC_6,CRC value 6 calculated for the section bytes" group.long 0x3009C++0x03 line.long 0x00 "TSD1_SF_CRC_7,CRC value 7 calculated for the section bytes" group.long 0x300A0++0x03 line.long 0x00 "TSD1_SF_CRC_8,CRC value 8 calculated for the section bytes" group.long 0x300A4++0x03 line.long 0x00 "TSD1_SF_CRC_9,CRC value 9 calculated for the section bytes" group.long 0x300A8++0x03 line.long 0x00 "TSD1_SF_CRC_10,CRC value 10 calculated for the section bytes" group.long 0x300AC++0x03 line.long 0x00 "TSD1_SF_CRC_11,CRC value 11 calculated for the section bytes" group.long 0x300B0++0x03 line.long 0x00 "TSD1_SF_CRC_12,CRC value 12 calculated for the section bytes" group.long 0x300B4++0x03 line.long 0x00 "TSD1_SF_CRC_13,CRC value 13 calculated for the section bytes" group.long 0x300B8++0x03 line.long 0x00 "TSD1_SF_CRC_14,CRC value 14 calculated for the section bytes" group.long 0x300BC++0x03 line.long 0x00 "TSD1_SF_CRC_15,CRC value 15 calculated for the section bytes" group.long 0x300C0++0x03 line.long 0x00 "TSD1_SF_CRC_16,CRC value 16 calculated for the section bytes" group.long 0x300C4++0x03 line.long 0x00 "TSD1_SF_CRC_17,CRC value 17 calculated for the section bytes" group.long 0x300C8++0x03 line.long 0x00 "TSD1_SF_CRC_18,CRC value 18 calculated for the section bytes" group.long 0x300CC++0x03 line.long 0x00 "TSD1_SF_CRC_19,CRC value 19 calculated for the section bytes" group.long 0x300D0++0x03 line.long 0x00 "TSD1_SF_CRC_20,CRC value 20 calculated for the section bytes" group.long 0x300D4++0x03 line.long 0x00 "TSD1_SF_CRC_21,CRC value 21 calculated for the section bytes" group.long 0x300D8++0x03 line.long 0x00 "TSD1_SF_CRC_22,CRC value 22 calculated for the section bytes" group.long 0x300DC++0x03 line.long 0x00 "TSD1_SF_CRC_23,CRC value 23 calculated for the section bytes" group.long 0x300E0++0x03 line.long 0x00 "TSD1_SF_CRC_24,CRC value 24 calculated for the section bytes" group.long 0x300E4++0x03 line.long 0x00 "TSD1_SF_CRC_25,CRC value 25 calculated for the section bytes" group.long 0x300E8++0x03 line.long 0x00 "TSD1_SF_CRC_26,CRC value 26 calculated for the section bytes" group.long 0x300EC++0x03 line.long 0x00 "TSD1_SF_CRC_27,CRC value 27 calculated for the section bytes" group.long 0x300F0++0x03 line.long 0x00 "TSD1_SF_CRC_28,CRC value 28 calculated for the section bytes" group.long 0x300F4++0x03 line.long 0x00 "TSD1_SF_CRC_29,CRC value 29 calculated for the section bytes" group.long 0x300F8++0x03 line.long 0x00 "TSD1_SF_CRC_30,CRC value 30 calculated for the section bytes" group.long 0x300FC++0x03 line.long 0x00 "TSD1_SF_CRC_31,CRC value 31 calculated for the section bytes" tree.end tree "TSD2" group.long 0x130080++0x03 line.long 0x00 "TSD2_SF_CRC_0,CRC value 0 calculated for the section bytes" group.long 0x130084++0x03 line.long 0x00 "TSD2_SF_CRC_1,CRC value 1 calculated for the section bytes" group.long 0x130088++0x03 line.long 0x00 "TSD2_SF_CRC_2,CRC value 2 calculated for the section bytes" group.long 0x13008C++0x03 line.long 0x00 "TSD2_SF_CRC_3,CRC value 3 calculated for the section bytes" group.long 0x130090++0x03 line.long 0x00 "TSD2_SF_CRC_4,CRC value 4 calculated for the section bytes" group.long 0x130094++0x03 line.long 0x00 "TSD2_SF_CRC_5,CRC value 5 calculated for the section bytes" group.long 0x130098++0x03 line.long 0x00 "TSD2_SF_CRC_6,CRC value 6 calculated for the section bytes" group.long 0x13009C++0x03 line.long 0x00 "TSD2_SF_CRC_7,CRC value 7 calculated for the section bytes" group.long 0x1300A0++0x03 line.long 0x00 "TSD2_SF_CRC_8,CRC value 8 calculated for the section bytes" group.long 0x1300A4++0x03 line.long 0x00 "TSD2_SF_CRC_9,CRC value 9 calculated for the section bytes" group.long 0x1300A8++0x03 line.long 0x00 "TSD2_SF_CRC_10,CRC value 10 calculated for the section bytes" group.long 0x1300AC++0x03 line.long 0x00 "TSD2_SF_CRC_11,CRC value 11 calculated for the section bytes" group.long 0x1300B0++0x03 line.long 0x00 "TSD2_SF_CRC_12,CRC value 12 calculated for the section bytes" group.long 0x1300B4++0x03 line.long 0x00 "TSD2_SF_CRC_13,CRC value 13 calculated for the section bytes" group.long 0x1300B8++0x03 line.long 0x00 "TSD2_SF_CRC_14,CRC value 14 calculated for the section bytes" group.long 0x1300BC++0x03 line.long 0x00 "TSD2_SF_CRC_15,CRC value 15 calculated for the section bytes" group.long 0x1300C0++0x03 line.long 0x00 "TSD2_SF_CRC_16,CRC value 16 calculated for the section bytes" group.long 0x1300C4++0x03 line.long 0x00 "TSD2_SF_CRC_17,CRC value 17 calculated for the section bytes" group.long 0x1300C8++0x03 line.long 0x00 "TSD2_SF_CRC_18,CRC value 18 calculated for the section bytes" group.long 0x1300CC++0x03 line.long 0x00 "TSD2_SF_CRC_19,CRC value 19 calculated for the section bytes" group.long 0x1300D0++0x03 line.long 0x00 "TSD2_SF_CRC_20,CRC value 20 calculated for the section bytes" group.long 0x1300D4++0x03 line.long 0x00 "TSD2_SF_CRC_21,CRC value 21 calculated for the section bytes" group.long 0x1300D8++0x03 line.long 0x00 "TSD2_SF_CRC_22,CRC value 22 calculated for the section bytes" group.long 0x1300DC++0x03 line.long 0x00 "TSD2_SF_CRC_23,CRC value 23 calculated for the section bytes" group.long 0x1300E0++0x03 line.long 0x00 "TSD2_SF_CRC_24,CRC value 24 calculated for the section bytes" group.long 0x1300E4++0x03 line.long 0x00 "TSD2_SF_CRC_25,CRC value 25 calculated for the section bytes" group.long 0x1300E8++0x03 line.long 0x00 "TSD2_SF_CRC_26,CRC value 26 calculated for the section bytes" group.long 0x1300EC++0x03 line.long 0x00 "TSD2_SF_CRC_27,CRC value 27 calculated for the section bytes" group.long 0x1300F0++0x03 line.long 0x00 "TSD2_SF_CRC_28,CRC value 28 calculated for the section bytes" group.long 0x1300F4++0x03 line.long 0x00 "TSD2_SF_CRC_29,CRC value 29 calculated for the section bytes" group.long 0x1300F8++0x03 line.long 0x00 "TSD2_SF_CRC_30,CRC value 30 calculated for the section bytes" group.long 0x1300FC++0x03 line.long 0x00 "TSD2_SF_CRC_31,CRC value 31 calculated for the section bytes" tree.end tree.end width 17. textline " " rgroup.long 0x30100++0x3 line.long 0x0 "TSD1_SF_ACTIVE,Each bit indicates if Section Filter of the corresponding PID is active" bitfld.long 0x0 31. " VALUE_31 ,Activate SF for PID31" "Not active,Active" bitfld.long 0x0 30. " VALUE_30 ,Activate SF for PID30" "Not active,Active" bitfld.long 0x0 29. " VALUE_29 ,Activate SF for PID29" "Not active,Active" textline " " bitfld.long 0x0 28. " VALUE_28 ,Activate SF for PID28" "Not active,Active" bitfld.long 0x0 27. " VALUE_27 ,Activate SF for PID27" "Not active,Active" bitfld.long 0x0 26. " VALUE_26 ,Activate SF for PID26" "Not active,Active" textline " " bitfld.long 0x0 25. " VALUE_25 ,Activate SF for PID25" "Not active,Active" bitfld.long 0x0 24. " VALUE_24 ,Activate SF for PID24" "Not active,Active" bitfld.long 0x0 23. " VALUE_23 ,Activate SF for PID23" "Not active,Active" textline " " bitfld.long 0x0 22. " VALUE_22 ,Activate SF for PID22" "Not active,Active" bitfld.long 0x0 21. " VALUE_21 ,Activate SF for PID21" "Not active,Active" bitfld.long 0x0 20. " VALUE_20 ,Activate SF for PID20" "Not active,Active" textline " " bitfld.long 0x0 19. " VALUE_19 ,Activate SF for PID19" "Not active,Active" bitfld.long 0x0 18. " VALUE_18 ,Activate SF for PID18" "Not active,Active" bitfld.long 0x0 17. " VALUE_17 ,Activate SF for PID17" "Not active,Active" textline " " bitfld.long 0x0 16. " VALUE_16 ,Activate SF for PID16" "Not active,Active" bitfld.long 0x0 15. " VALUE_15 ,Activate SF for PID15" "Not active,Active" bitfld.long 0x0 14. " VALUE_14 ,Activate SF for PID14" "Not active,Active" textline " " bitfld.long 0x0 13. " VALUE_13 ,Activate SF for PID13" "Not active,Active" bitfld.long 0x0 12. " VALUE_12 ,Activate SF for PID12" "Not active,Active" bitfld.long 0x0 11. " VALUE_11 ,Activate SF for PID11" "Not active,Active" textline " " bitfld.long 0x0 10. " VALUE_10 ,Activate SF for PID10" "Not active,Active" bitfld.long 0x0 9. " VALUE_9 ,Activate SF for PID9" "Not active,Active" bitfld.long 0x0 8. " VALUE_8 ,Activate SF for PID8" "Not active,Active" textline " " bitfld.long 0x0 7. " VALUE_7 ,Activate SF for PID7" "Not active,Active" bitfld.long 0x0 6. " VALUE_6 ,Activate SF for PID6" "Not active,Active" bitfld.long 0x0 5. " VALUE_5 ,Activate SF for PID5" "Not active,Active" textline " " bitfld.long 0x0 4. " VALUE_4 ,Activate SF for PID4" "Not active,Active" bitfld.long 0x0 3. " VALUE_3 ,Activate SF for PID3" "Not active,Active" bitfld.long 0x0 2. " VALUE_2 ,Activate SF for PID2" "Not active,Active" textline " " bitfld.long 0x0 1. " VALUE_1 ,Activate SF for PID1" "Not active,Active" bitfld.long 0x0 0. " VALUE_0 ,Activate SF for PID0" "Not active,Active" rgroup.long 0x130100++0x3 line.long 0x0 "TSD2_SF_ACTIVE,Each bit indicates if Section Filter of the corresponding PID is active" bitfld.long 0x0 31. " VALUE_31 ,Activate SF for PID31" "Not active,Active" bitfld.long 0x0 30. " VALUE_30 ,Activate SF for PID30" "Not active,Active" bitfld.long 0x0 29. " VALUE_29 ,Activate SF for PID29" "Not active,Active" textline " " bitfld.long 0x0 28. " VALUE_28 ,Activate SF for PID28" "Not active,Active" bitfld.long 0x0 27. " VALUE_27 ,Activate SF for PID27" "Not active,Active" bitfld.long 0x0 26. " VALUE_26 ,Activate SF for PID26" "Not active,Active" textline " " bitfld.long 0x0 25. " VALUE_25 ,Activate SF for PID25" "Not active,Active" bitfld.long 0x0 24. " VALUE_24 ,Activate SF for PID24" "Not active,Active" bitfld.long 0x0 23. " VALUE_23 ,Activate SF for PID23" "Not active,Active" textline " " bitfld.long 0x0 22. " VALUE_22 ,Activate SF for PID22" "Not active,Active" bitfld.long 0x0 21. " VALUE_21 ,Activate SF for PID21" "Not active,Active" bitfld.long 0x0 20. " VALUE_20 ,Activate SF for PID20" "Not active,Active" textline " " bitfld.long 0x0 19. " VALUE_19 ,Activate SF for PID19" "Not active,Active" bitfld.long 0x0 18. " VALUE_18 ,Activate SF for PID18" "Not active,Active" bitfld.long 0x0 17. " VALUE_17 ,Activate SF for PID17" "Not active,Active" textline " " bitfld.long 0x0 16. " VALUE_16 ,Activate SF for PID16" "Not active,Active" bitfld.long 0x0 15. " VALUE_15 ,Activate SF for PID15" "Not active,Active" bitfld.long 0x0 14. " VALUE_14 ,Activate SF for PID14" "Not active,Active" textline " " bitfld.long 0x0 13. " VALUE_13 ,Activate SF for PID13" "Not active,Active" bitfld.long 0x0 12. " VALUE_12 ,Activate SF for PID12" "Not active,Active" bitfld.long 0x0 11. " VALUE_11 ,Activate SF for PID11" "Not active,Active" textline " " bitfld.long 0x0 10. " VALUE_10 ,Activate SF for PID10" "Not active,Active" bitfld.long 0x0 9. " VALUE_9 ,Activate SF for PID9" "Not active,Active" bitfld.long 0x0 8. " VALUE_8 ,Activate SF for PID8" "Not active,Active" textline " " bitfld.long 0x0 7. " VALUE_7 ,Activate SF for PID7" "Not active,Active" bitfld.long 0x0 6. " VALUE_6 ,Activate SF for PID6" "Not active,Active" bitfld.long 0x0 5. " VALUE_5 ,Activate SF for PID5" "Not active,Active" textline " " bitfld.long 0x0 4. " VALUE_4 ,Activate SF for PID4" "Not active,Active" bitfld.long 0x0 3. " VALUE_3 ,Activate SF for PID3" "Not active,Active" bitfld.long 0x0 2. " VALUE_2 ,Activate SF for PID2" "Not active,Active" textline " " bitfld.long 0x0 1. " VALUE_1 ,Activate SF for PID1" "Not active,Active" bitfld.long 0x0 0. " VALUE_0 ,Activate SF for PID0" "Not active,Active" width 21. tree "Targests" tree "TSD1" wgroup.long 0x40000++0x03 line.long 0x00 "TSD1_SF_TARGETS_0,Targest 0 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40004++0x03 line.long 0x00 "TSD1_SF_TARGETS_1,Targest 1 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40008++0x03 line.long 0x00 "TSD1_SF_TARGETS_2,Targest 2 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4000C++0x03 line.long 0x00 "TSD1_SF_TARGETS_3,Targest 3 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40010++0x03 line.long 0x00 "TSD1_SF_TARGETS_4,Targest 4 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40014++0x03 line.long 0x00 "TSD1_SF_TARGETS_5,Targest 5 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40018++0x03 line.long 0x00 "TSD1_SF_TARGETS_6,Targest 6 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4001C++0x03 line.long 0x00 "TSD1_SF_TARGETS_7,Targest 7 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40020++0x03 line.long 0x00 "TSD1_SF_TARGETS_8,Targest 8 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40024++0x03 line.long 0x00 "TSD1_SF_TARGETS_9,Targest 9 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40028++0x03 line.long 0x00 "TSD1_SF_TARGETS_10,Targest 10 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4002C++0x03 line.long 0x00 "TSD1_SF_TARGETS_11,Targest 11 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40030++0x03 line.long 0x00 "TSD1_SF_TARGETS_12,Targest 12 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40034++0x03 line.long 0x00 "TSD1_SF_TARGETS_13,Targest 13 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40038++0x03 line.long 0x00 "TSD1_SF_TARGETS_14,Targest 14 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4003C++0x03 line.long 0x00 "TSD1_SF_TARGETS_15,Targest 15 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40040++0x03 line.long 0x00 "TSD1_SF_TARGETS_16,Targest 16 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40044++0x03 line.long 0x00 "TSD1_SF_TARGETS_17,Targest 17 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40048++0x03 line.long 0x00 "TSD1_SF_TARGETS_18,Targest 18 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4004C++0x03 line.long 0x00 "TSD1_SF_TARGETS_19,Targest 19 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40050++0x03 line.long 0x00 "TSD1_SF_TARGETS_20,Targest 20 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40054++0x03 line.long 0x00 "TSD1_SF_TARGETS_21,Targest 21 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40058++0x03 line.long 0x00 "TSD1_SF_TARGETS_22,Targest 22 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4005C++0x03 line.long 0x00 "TSD1_SF_TARGETS_23,Targest 23 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40060++0x03 line.long 0x00 "TSD1_SF_TARGETS_24,Targest 24 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40064++0x03 line.long 0x00 "TSD1_SF_TARGETS_25,Targest 25 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40068++0x03 line.long 0x00 "TSD1_SF_TARGETS_26,Targest 26 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4006C++0x03 line.long 0x00 "TSD1_SF_TARGETS_27,Targest 27 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40070++0x03 line.long 0x00 "TSD1_SF_TARGETS_28,Targest 28 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40074++0x03 line.long 0x00 "TSD1_SF_TARGETS_29,Targest 29 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40078++0x03 line.long 0x00 "TSD1_SF_TARGETS_30,Targest 30 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4007C++0x03 line.long 0x00 "TSD1_SF_TARGETS_31,Targest 31 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40080++0x03 line.long 0x00 "TSD1_SF_TARGETS_32,Targest 32 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40084++0x03 line.long 0x00 "TSD1_SF_TARGETS_33,Targest 33 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40088++0x03 line.long 0x00 "TSD1_SF_TARGETS_34,Targest 34 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4008C++0x03 line.long 0x00 "TSD1_SF_TARGETS_35,Targest 35 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40090++0x03 line.long 0x00 "TSD1_SF_TARGETS_36,Targest 36 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40094++0x03 line.long 0x00 "TSD1_SF_TARGETS_37,Targest 37 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40098++0x03 line.long 0x00 "TSD1_SF_TARGETS_38,Targest 38 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4009C++0x03 line.long 0x00 "TSD1_SF_TARGETS_39,Targest 39 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400A0++0x03 line.long 0x00 "TSD1_SF_TARGETS_40,Targest 40 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400A4++0x03 line.long 0x00 "TSD1_SF_TARGETS_41,Targest 41 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400A8++0x03 line.long 0x00 "TSD1_SF_TARGETS_42,Targest 42 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400AC++0x03 line.long 0x00 "TSD1_SF_TARGETS_43,Targest 43 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400B0++0x03 line.long 0x00 "TSD1_SF_TARGETS_44,Targest 44 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400B4++0x03 line.long 0x00 "TSD1_SF_TARGETS_45,Targest 45 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400B8++0x03 line.long 0x00 "TSD1_SF_TARGETS_46,Targest 46 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400BC++0x03 line.long 0x00 "TSD1_SF_TARGETS_47,Targest 47 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400C0++0x03 line.long 0x00 "TSD1_SF_TARGETS_48,Targest 48 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400C4++0x03 line.long 0x00 "TSD1_SF_TARGETS_49,Targest 49 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400C8++0x03 line.long 0x00 "TSD1_SF_TARGETS_50,Targest 50 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400CC++0x03 line.long 0x00 "TSD1_SF_TARGETS_51,Targest 51 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400D0++0x03 line.long 0x00 "TSD1_SF_TARGETS_52,Targest 52 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400D4++0x03 line.long 0x00 "TSD1_SF_TARGETS_53,Targest 53 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400D8++0x03 line.long 0x00 "TSD1_SF_TARGETS_54,Targest 54 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400DC++0x03 line.long 0x00 "TSD1_SF_TARGETS_55,Targest 55 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400E0++0x03 line.long 0x00 "TSD1_SF_TARGETS_56,Targest 56 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400E4++0x03 line.long 0x00 "TSD1_SF_TARGETS_57,Targest 57 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400E8++0x03 line.long 0x00 "TSD1_SF_TARGETS_58,Targest 58 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400EC++0x03 line.long 0x00 "TSD1_SF_TARGETS_59,Targest 59 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400F0++0x03 line.long 0x00 "TSD1_SF_TARGETS_60,Targest 60 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400F4++0x03 line.long 0x00 "TSD1_SF_TARGETS_61,Targest 61 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400F8++0x03 line.long 0x00 "TSD1_SF_TARGETS_62,Targest 62 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x400FC++0x03 line.long 0x00 "TSD1_SF_TARGETS_63,Targest 63 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40100++0x03 line.long 0x00 "TSD1_SF_TARGETS_64,Targest 64 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40104++0x03 line.long 0x00 "TSD1_SF_TARGETS_65,Targest 65 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40108++0x03 line.long 0x00 "TSD1_SF_TARGETS_66,Targest 66 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4010C++0x03 line.long 0x00 "TSD1_SF_TARGETS_67,Targest 67 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40110++0x03 line.long 0x00 "TSD1_SF_TARGETS_68,Targest 68 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40114++0x03 line.long 0x00 "TSD1_SF_TARGETS_69,Targest 69 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40118++0x03 line.long 0x00 "TSD1_SF_TARGETS_70,Targest 70 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4011C++0x03 line.long 0x00 "TSD1_SF_TARGETS_71,Targest 71 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40120++0x03 line.long 0x00 "TSD1_SF_TARGETS_72,Targest 72 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40124++0x03 line.long 0x00 "TSD1_SF_TARGETS_73,Targest 73 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40128++0x03 line.long 0x00 "TSD1_SF_TARGETS_74,Targest 74 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4012C++0x03 line.long 0x00 "TSD1_SF_TARGETS_75,Targest 75 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40130++0x03 line.long 0x00 "TSD1_SF_TARGETS_76,Targest 76 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40134++0x03 line.long 0x00 "TSD1_SF_TARGETS_77,Targest 77 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40138++0x03 line.long 0x00 "TSD1_SF_TARGETS_78,Targest 78 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4013C++0x03 line.long 0x00 "TSD1_SF_TARGETS_79,Targest 79 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40140++0x03 line.long 0x00 "TSD1_SF_TARGETS_80,Targest 80 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40144++0x03 line.long 0x00 "TSD1_SF_TARGETS_81,Targest 81 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40148++0x03 line.long 0x00 "TSD1_SF_TARGETS_82,Targest 82 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4014C++0x03 line.long 0x00 "TSD1_SF_TARGETS_83,Targest 83 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40150++0x03 line.long 0x00 "TSD1_SF_TARGETS_84,Targest 84 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40154++0x03 line.long 0x00 "TSD1_SF_TARGETS_85,Targest 85 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40158++0x03 line.long 0x00 "TSD1_SF_TARGETS_86,Targest 86 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4015C++0x03 line.long 0x00 "TSD1_SF_TARGETS_87,Targest 87 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40160++0x03 line.long 0x00 "TSD1_SF_TARGETS_88,Targest 88 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40164++0x03 line.long 0x00 "TSD1_SF_TARGETS_89,Targest 89 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40168++0x03 line.long 0x00 "TSD1_SF_TARGETS_90,Targest 90 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4016C++0x03 line.long 0x00 "TSD1_SF_TARGETS_91,Targest 91 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40170++0x03 line.long 0x00 "TSD1_SF_TARGETS_92,Targest 92 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40174++0x03 line.long 0x00 "TSD1_SF_TARGETS_93,Targest 93 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40178++0x03 line.long 0x00 "TSD1_SF_TARGETS_94,Targest 94 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4017C++0x03 line.long 0x00 "TSD1_SF_TARGETS_95,Targest 95 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40180++0x03 line.long 0x00 "TSD1_SF_TARGETS_96,Targest 96 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40184++0x03 line.long 0x00 "TSD1_SF_TARGETS_97,Targest 97 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40188++0x03 line.long 0x00 "TSD1_SF_TARGETS_98,Targest 98 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4018C++0x03 line.long 0x00 "TSD1_SF_TARGETS_99,Targest 99 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40190++0x03 line.long 0x00 "TSD1_SF_TARGETS_100,Targest 100 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40194++0x03 line.long 0x00 "TSD1_SF_TARGETS_101,Targest 101 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40198++0x03 line.long 0x00 "TSD1_SF_TARGETS_102,Targest 102 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4019C++0x03 line.long 0x00 "TSD1_SF_TARGETS_103,Targest 103 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401A0++0x03 line.long 0x00 "TSD1_SF_TARGETS_104,Targest 104 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401A4++0x03 line.long 0x00 "TSD1_SF_TARGETS_105,Targest 105 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401A8++0x03 line.long 0x00 "TSD1_SF_TARGETS_106,Targest 106 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401AC++0x03 line.long 0x00 "TSD1_SF_TARGETS_107,Targest 107 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401B0++0x03 line.long 0x00 "TSD1_SF_TARGETS_108,Targest 108 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401B4++0x03 line.long 0x00 "TSD1_SF_TARGETS_109,Targest 109 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401B8++0x03 line.long 0x00 "TSD1_SF_TARGETS_110,Targest 110 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401BC++0x03 line.long 0x00 "TSD1_SF_TARGETS_111,Targest 111 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401C0++0x03 line.long 0x00 "TSD1_SF_TARGETS_112,Targest 112 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401C4++0x03 line.long 0x00 "TSD1_SF_TARGETS_113,Targest 113 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401C8++0x03 line.long 0x00 "TSD1_SF_TARGETS_114,Targest 114 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401CC++0x03 line.long 0x00 "TSD1_SF_TARGETS_115,Targest 115 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401D0++0x03 line.long 0x00 "TSD1_SF_TARGETS_116,Targest 116 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401D4++0x03 line.long 0x00 "TSD1_SF_TARGETS_117,Targest 117 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401D8++0x03 line.long 0x00 "TSD1_SF_TARGETS_118,Targest 118 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401DC++0x03 line.long 0x00 "TSD1_SF_TARGETS_119,Targest 119 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401E0++0x03 line.long 0x00 "TSD1_SF_TARGETS_120,Targest 120 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401E4++0x03 line.long 0x00 "TSD1_SF_TARGETS_121,Targest 121 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401E8++0x03 line.long 0x00 "TSD1_SF_TARGETS_122,Targest 122 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401EC++0x03 line.long 0x00 "TSD1_SF_TARGETS_123,Targest 123 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401F0++0x03 line.long 0x00 "TSD1_SF_TARGETS_124,Targest 124 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401F4++0x03 line.long 0x00 "TSD1_SF_TARGETS_125,Targest 125 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401F8++0x03 line.long 0x00 "TSD1_SF_TARGETS_126,Targest 126 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x401FC++0x03 line.long 0x00 "TSD1_SF_TARGETS_127,Targest 127 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40200++0x03 line.long 0x00 "TSD1_SF_TARGETS_128,Targest 128 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40204++0x03 line.long 0x00 "TSD1_SF_TARGETS_129,Targest 129 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40208++0x03 line.long 0x00 "TSD1_SF_TARGETS_130,Targest 130 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4020C++0x03 line.long 0x00 "TSD1_SF_TARGETS_131,Targest 131 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40210++0x03 line.long 0x00 "TSD1_SF_TARGETS_132,Targest 132 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40214++0x03 line.long 0x00 "TSD1_SF_TARGETS_133,Targest 133 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40218++0x03 line.long 0x00 "TSD1_SF_TARGETS_134,Targest 134 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4021C++0x03 line.long 0x00 "TSD1_SF_TARGETS_135,Targest 135 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40220++0x03 line.long 0x00 "TSD1_SF_TARGETS_136,Targest 136 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40224++0x03 line.long 0x00 "TSD1_SF_TARGETS_137,Targest 137 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40228++0x03 line.long 0x00 "TSD1_SF_TARGETS_138,Targest 138 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4022C++0x03 line.long 0x00 "TSD1_SF_TARGETS_139,Targest 139 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40230++0x03 line.long 0x00 "TSD1_SF_TARGETS_140,Targest 140 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40234++0x03 line.long 0x00 "TSD1_SF_TARGETS_141,Targest 141 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40238++0x03 line.long 0x00 "TSD1_SF_TARGETS_142,Targest 142 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4023C++0x03 line.long 0x00 "TSD1_SF_TARGETS_143,Targest 143 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40240++0x03 line.long 0x00 "TSD1_SF_TARGETS_144,Targest 144 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40244++0x03 line.long 0x00 "TSD1_SF_TARGETS_145,Targest 145 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40248++0x03 line.long 0x00 "TSD1_SF_TARGETS_146,Targest 146 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4024C++0x03 line.long 0x00 "TSD1_SF_TARGETS_147,Targest 147 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40250++0x03 line.long 0x00 "TSD1_SF_TARGETS_148,Targest 148 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40254++0x03 line.long 0x00 "TSD1_SF_TARGETS_149,Targest 149 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40258++0x03 line.long 0x00 "TSD1_SF_TARGETS_150,Targest 150 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4025C++0x03 line.long 0x00 "TSD1_SF_TARGETS_151,Targest 151 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40260++0x03 line.long 0x00 "TSD1_SF_TARGETS_152,Targest 152 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40264++0x03 line.long 0x00 "TSD1_SF_TARGETS_153,Targest 153 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40268++0x03 line.long 0x00 "TSD1_SF_TARGETS_154,Targest 154 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4026C++0x03 line.long 0x00 "TSD1_SF_TARGETS_155,Targest 155 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40270++0x03 line.long 0x00 "TSD1_SF_TARGETS_156,Targest 156 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40274++0x03 line.long 0x00 "TSD1_SF_TARGETS_157,Targest 157 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40278++0x03 line.long 0x00 "TSD1_SF_TARGETS_158,Targest 158 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4027C++0x03 line.long 0x00 "TSD1_SF_TARGETS_159,Targest 159 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40280++0x03 line.long 0x00 "TSD1_SF_TARGETS_160,Targest 160 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40284++0x03 line.long 0x00 "TSD1_SF_TARGETS_161,Targest 161 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40288++0x03 line.long 0x00 "TSD1_SF_TARGETS_162,Targest 162 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4028C++0x03 line.long 0x00 "TSD1_SF_TARGETS_163,Targest 163 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40290++0x03 line.long 0x00 "TSD1_SF_TARGETS_164,Targest 164 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40294++0x03 line.long 0x00 "TSD1_SF_TARGETS_165,Targest 165 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40298++0x03 line.long 0x00 "TSD1_SF_TARGETS_166,Targest 166 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4029C++0x03 line.long 0x00 "TSD1_SF_TARGETS_167,Targest 167 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402A0++0x03 line.long 0x00 "TSD1_SF_TARGETS_168,Targest 168 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402A4++0x03 line.long 0x00 "TSD1_SF_TARGETS_169,Targest 169 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402A8++0x03 line.long 0x00 "TSD1_SF_TARGETS_170,Targest 170 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402AC++0x03 line.long 0x00 "TSD1_SF_TARGETS_171,Targest 171 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402B0++0x03 line.long 0x00 "TSD1_SF_TARGETS_172,Targest 172 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402B4++0x03 line.long 0x00 "TSD1_SF_TARGETS_173,Targest 173 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402B8++0x03 line.long 0x00 "TSD1_SF_TARGETS_174,Targest 174 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402BC++0x03 line.long 0x00 "TSD1_SF_TARGETS_175,Targest 175 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402C0++0x03 line.long 0x00 "TSD1_SF_TARGETS_176,Targest 176 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402C4++0x03 line.long 0x00 "TSD1_SF_TARGETS_177,Targest 177 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402C8++0x03 line.long 0x00 "TSD1_SF_TARGETS_178,Targest 178 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402CC++0x03 line.long 0x00 "TSD1_SF_TARGETS_179,Targest 179 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402D0++0x03 line.long 0x00 "TSD1_SF_TARGETS_180,Targest 180 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402D4++0x03 line.long 0x00 "TSD1_SF_TARGETS_181,Targest 181 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402D8++0x03 line.long 0x00 "TSD1_SF_TARGETS_182,Targest 182 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402DC++0x03 line.long 0x00 "TSD1_SF_TARGETS_183,Targest 183 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402E0++0x03 line.long 0x00 "TSD1_SF_TARGETS_184,Targest 184 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402E4++0x03 line.long 0x00 "TSD1_SF_TARGETS_185,Targest 185 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402E8++0x03 line.long 0x00 "TSD1_SF_TARGETS_186,Targest 186 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402EC++0x03 line.long 0x00 "TSD1_SF_TARGETS_187,Targest 187 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402F0++0x03 line.long 0x00 "TSD1_SF_TARGETS_188,Targest 188 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402F4++0x03 line.long 0x00 "TSD1_SF_TARGETS_189,Targest 189 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402F8++0x03 line.long 0x00 "TSD1_SF_TARGETS_190,Targest 190 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x402FC++0x03 line.long 0x00 "TSD1_SF_TARGETS_191,Targest 191 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40300++0x03 line.long 0x00 "TSD1_SF_TARGETS_192,Targest 192 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40304++0x03 line.long 0x00 "TSD1_SF_TARGETS_193,Targest 193 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40308++0x03 line.long 0x00 "TSD1_SF_TARGETS_194,Targest 194 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4030C++0x03 line.long 0x00 "TSD1_SF_TARGETS_195,Targest 195 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40310++0x03 line.long 0x00 "TSD1_SF_TARGETS_196,Targest 196 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40314++0x03 line.long 0x00 "TSD1_SF_TARGETS_197,Targest 197 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40318++0x03 line.long 0x00 "TSD1_SF_TARGETS_198,Targest 198 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4031C++0x03 line.long 0x00 "TSD1_SF_TARGETS_199,Targest 199 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40320++0x03 line.long 0x00 "TSD1_SF_TARGETS_200,Targest 200 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40324++0x03 line.long 0x00 "TSD1_SF_TARGETS_201,Targest 201 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40328++0x03 line.long 0x00 "TSD1_SF_TARGETS_202,Targest 202 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4032C++0x03 line.long 0x00 "TSD1_SF_TARGETS_203,Targest 203 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40330++0x03 line.long 0x00 "TSD1_SF_TARGETS_204,Targest 204 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40334++0x03 line.long 0x00 "TSD1_SF_TARGETS_205,Targest 205 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40338++0x03 line.long 0x00 "TSD1_SF_TARGETS_206,Targest 206 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4033C++0x03 line.long 0x00 "TSD1_SF_TARGETS_207,Targest 207 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40340++0x03 line.long 0x00 "TSD1_SF_TARGETS_208,Targest 208 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40344++0x03 line.long 0x00 "TSD1_SF_TARGETS_209,Targest 209 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40348++0x03 line.long 0x00 "TSD1_SF_TARGETS_210,Targest 210 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4034C++0x03 line.long 0x00 "TSD1_SF_TARGETS_211,Targest 211 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40350++0x03 line.long 0x00 "TSD1_SF_TARGETS_212,Targest 212 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40354++0x03 line.long 0x00 "TSD1_SF_TARGETS_213,Targest 213 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40358++0x03 line.long 0x00 "TSD1_SF_TARGETS_214,Targest 214 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4035C++0x03 line.long 0x00 "TSD1_SF_TARGETS_215,Targest 215 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40360++0x03 line.long 0x00 "TSD1_SF_TARGETS_216,Targest 216 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40364++0x03 line.long 0x00 "TSD1_SF_TARGETS_217,Targest 217 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40368++0x03 line.long 0x00 "TSD1_SF_TARGETS_218,Targest 218 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4036C++0x03 line.long 0x00 "TSD1_SF_TARGETS_219,Targest 219 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40370++0x03 line.long 0x00 "TSD1_SF_TARGETS_220,Targest 220 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40374++0x03 line.long 0x00 "TSD1_SF_TARGETS_221,Targest 221 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40378++0x03 line.long 0x00 "TSD1_SF_TARGETS_222,Targest 222 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4037C++0x03 line.long 0x00 "TSD1_SF_TARGETS_223,Targest 223 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40380++0x03 line.long 0x00 "TSD1_SF_TARGETS_224,Targest 224 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40384++0x03 line.long 0x00 "TSD1_SF_TARGETS_225,Targest 225 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40388++0x03 line.long 0x00 "TSD1_SF_TARGETS_226,Targest 226 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4038C++0x03 line.long 0x00 "TSD1_SF_TARGETS_227,Targest 227 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40390++0x03 line.long 0x00 "TSD1_SF_TARGETS_228,Targest 228 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40394++0x03 line.long 0x00 "TSD1_SF_TARGETS_229,Targest 229 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x40398++0x03 line.long 0x00 "TSD1_SF_TARGETS_230,Targest 230 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x4039C++0x03 line.long 0x00 "TSD1_SF_TARGETS_231,Targest 231 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403A0++0x03 line.long 0x00 "TSD1_SF_TARGETS_232,Targest 232 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403A4++0x03 line.long 0x00 "TSD1_SF_TARGETS_233,Targest 233 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403A8++0x03 line.long 0x00 "TSD1_SF_TARGETS_234,Targest 234 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403AC++0x03 line.long 0x00 "TSD1_SF_TARGETS_235,Targest 235 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403B0++0x03 line.long 0x00 "TSD1_SF_TARGETS_236,Targest 236 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403B4++0x03 line.long 0x00 "TSD1_SF_TARGETS_237,Targest 237 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403B8++0x03 line.long 0x00 "TSD1_SF_TARGETS_238,Targest 238 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403BC++0x03 line.long 0x00 "TSD1_SF_TARGETS_239,Targest 239 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403C0++0x03 line.long 0x00 "TSD1_SF_TARGETS_240,Targest 240 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403C4++0x03 line.long 0x00 "TSD1_SF_TARGETS_241,Targest 241 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403C8++0x03 line.long 0x00 "TSD1_SF_TARGETS_242,Targest 242 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403CC++0x03 line.long 0x00 "TSD1_SF_TARGETS_243,Targest 243 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403D0++0x03 line.long 0x00 "TSD1_SF_TARGETS_244,Targest 244 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403D4++0x03 line.long 0x00 "TSD1_SF_TARGETS_245,Targest 245 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403D8++0x03 line.long 0x00 "TSD1_SF_TARGETS_246,Targest 246 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403DC++0x03 line.long 0x00 "TSD1_SF_TARGETS_247,Targest 247 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403E0++0x03 line.long 0x00 "TSD1_SF_TARGETS_248,Targest 248 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403E4++0x03 line.long 0x00 "TSD1_SF_TARGETS_249,Targest 249 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403E8++0x03 line.long 0x00 "TSD1_SF_TARGETS_250,Targest 250 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403EC++0x03 line.long 0x00 "TSD1_SF_TARGETS_251,Targest 251 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403F0++0x03 line.long 0x00 "TSD1_SF_TARGETS_252,Targest 252 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403F4++0x03 line.long 0x00 "TSD1_SF_TARGETS_253,Targest 253 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403F8++0x03 line.long 0x00 "TSD1_SF_TARGETS_254,Targest 254 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x403FC++0x03 line.long 0x00 "TSD1_SF_TARGETS_255,Targest 255 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" tree.end tree "TSD2" wgroup.long 0x140000++0x03 line.long 0x00 "TSD2_SF_TARGETS_0,Targest 0 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140004++0x03 line.long 0x00 "TSD2_SF_TARGETS_1,Targest 1 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140008++0x03 line.long 0x00 "TSD2_SF_TARGETS_2,Targest 2 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14000C++0x03 line.long 0x00 "TSD2_SF_TARGETS_3,Targest 3 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140010++0x03 line.long 0x00 "TSD2_SF_TARGETS_4,Targest 4 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140014++0x03 line.long 0x00 "TSD2_SF_TARGETS_5,Targest 5 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140018++0x03 line.long 0x00 "TSD2_SF_TARGETS_6,Targest 6 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14001C++0x03 line.long 0x00 "TSD2_SF_TARGETS_7,Targest 7 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140020++0x03 line.long 0x00 "TSD2_SF_TARGETS_8,Targest 8 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140024++0x03 line.long 0x00 "TSD2_SF_TARGETS_9,Targest 9 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140028++0x03 line.long 0x00 "TSD2_SF_TARGETS_10,Targest 10 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14002C++0x03 line.long 0x00 "TSD2_SF_TARGETS_11,Targest 11 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140030++0x03 line.long 0x00 "TSD2_SF_TARGETS_12,Targest 12 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140034++0x03 line.long 0x00 "TSD2_SF_TARGETS_13,Targest 13 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140038++0x03 line.long 0x00 "TSD2_SF_TARGETS_14,Targest 14 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14003C++0x03 line.long 0x00 "TSD2_SF_TARGETS_15,Targest 15 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140040++0x03 line.long 0x00 "TSD2_SF_TARGETS_16,Targest 16 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140044++0x03 line.long 0x00 "TSD2_SF_TARGETS_17,Targest 17 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140048++0x03 line.long 0x00 "TSD2_SF_TARGETS_18,Targest 18 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14004C++0x03 line.long 0x00 "TSD2_SF_TARGETS_19,Targest 19 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140050++0x03 line.long 0x00 "TSD2_SF_TARGETS_20,Targest 20 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140054++0x03 line.long 0x00 "TSD2_SF_TARGETS_21,Targest 21 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140058++0x03 line.long 0x00 "TSD2_SF_TARGETS_22,Targest 22 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14005C++0x03 line.long 0x00 "TSD2_SF_TARGETS_23,Targest 23 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140060++0x03 line.long 0x00 "TSD2_SF_TARGETS_24,Targest 24 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140064++0x03 line.long 0x00 "TSD2_SF_TARGETS_25,Targest 25 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140068++0x03 line.long 0x00 "TSD2_SF_TARGETS_26,Targest 26 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14006C++0x03 line.long 0x00 "TSD2_SF_TARGETS_27,Targest 27 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140070++0x03 line.long 0x00 "TSD2_SF_TARGETS_28,Targest 28 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140074++0x03 line.long 0x00 "TSD2_SF_TARGETS_29,Targest 29 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140078++0x03 line.long 0x00 "TSD2_SF_TARGETS_30,Targest 30 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14007C++0x03 line.long 0x00 "TSD2_SF_TARGETS_31,Targest 31 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140080++0x03 line.long 0x00 "TSD2_SF_TARGETS_32,Targest 32 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140084++0x03 line.long 0x00 "TSD2_SF_TARGETS_33,Targest 33 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140088++0x03 line.long 0x00 "TSD2_SF_TARGETS_34,Targest 34 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14008C++0x03 line.long 0x00 "TSD2_SF_TARGETS_35,Targest 35 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140090++0x03 line.long 0x00 "TSD2_SF_TARGETS_36,Targest 36 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140094++0x03 line.long 0x00 "TSD2_SF_TARGETS_37,Targest 37 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140098++0x03 line.long 0x00 "TSD2_SF_TARGETS_38,Targest 38 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14009C++0x03 line.long 0x00 "TSD2_SF_TARGETS_39,Targest 39 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400A0++0x03 line.long 0x00 "TSD2_SF_TARGETS_40,Targest 40 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400A4++0x03 line.long 0x00 "TSD2_SF_TARGETS_41,Targest 41 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400A8++0x03 line.long 0x00 "TSD2_SF_TARGETS_42,Targest 42 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400AC++0x03 line.long 0x00 "TSD2_SF_TARGETS_43,Targest 43 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400B0++0x03 line.long 0x00 "TSD2_SF_TARGETS_44,Targest 44 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400B4++0x03 line.long 0x00 "TSD2_SF_TARGETS_45,Targest 45 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400B8++0x03 line.long 0x00 "TSD2_SF_TARGETS_46,Targest 46 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400BC++0x03 line.long 0x00 "TSD2_SF_TARGETS_47,Targest 47 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400C0++0x03 line.long 0x00 "TSD2_SF_TARGETS_48,Targest 48 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400C4++0x03 line.long 0x00 "TSD2_SF_TARGETS_49,Targest 49 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400C8++0x03 line.long 0x00 "TSD2_SF_TARGETS_50,Targest 50 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400CC++0x03 line.long 0x00 "TSD2_SF_TARGETS_51,Targest 51 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400D0++0x03 line.long 0x00 "TSD2_SF_TARGETS_52,Targest 52 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400D4++0x03 line.long 0x00 "TSD2_SF_TARGETS_53,Targest 53 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400D8++0x03 line.long 0x00 "TSD2_SF_TARGETS_54,Targest 54 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400DC++0x03 line.long 0x00 "TSD2_SF_TARGETS_55,Targest 55 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400E0++0x03 line.long 0x00 "TSD2_SF_TARGETS_56,Targest 56 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400E4++0x03 line.long 0x00 "TSD2_SF_TARGETS_57,Targest 57 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400E8++0x03 line.long 0x00 "TSD2_SF_TARGETS_58,Targest 58 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400EC++0x03 line.long 0x00 "TSD2_SF_TARGETS_59,Targest 59 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400F0++0x03 line.long 0x00 "TSD2_SF_TARGETS_60,Targest 60 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400F4++0x03 line.long 0x00 "TSD2_SF_TARGETS_61,Targest 61 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400F8++0x03 line.long 0x00 "TSD2_SF_TARGETS_62,Targest 62 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1400FC++0x03 line.long 0x00 "TSD2_SF_TARGETS_63,Targest 63 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140100++0x03 line.long 0x00 "TSD2_SF_TARGETS_64,Targest 64 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140104++0x03 line.long 0x00 "TSD2_SF_TARGETS_65,Targest 65 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140108++0x03 line.long 0x00 "TSD2_SF_TARGETS_66,Targest 66 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14010C++0x03 line.long 0x00 "TSD2_SF_TARGETS_67,Targest 67 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140110++0x03 line.long 0x00 "TSD2_SF_TARGETS_68,Targest 68 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140114++0x03 line.long 0x00 "TSD2_SF_TARGETS_69,Targest 69 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140118++0x03 line.long 0x00 "TSD2_SF_TARGETS_70,Targest 70 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14011C++0x03 line.long 0x00 "TSD2_SF_TARGETS_71,Targest 71 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140120++0x03 line.long 0x00 "TSD2_SF_TARGETS_72,Targest 72 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140124++0x03 line.long 0x00 "TSD2_SF_TARGETS_73,Targest 73 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140128++0x03 line.long 0x00 "TSD2_SF_TARGETS_74,Targest 74 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14012C++0x03 line.long 0x00 "TSD2_SF_TARGETS_75,Targest 75 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140130++0x03 line.long 0x00 "TSD2_SF_TARGETS_76,Targest 76 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140134++0x03 line.long 0x00 "TSD2_SF_TARGETS_77,Targest 77 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140138++0x03 line.long 0x00 "TSD2_SF_TARGETS_78,Targest 78 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14013C++0x03 line.long 0x00 "TSD2_SF_TARGETS_79,Targest 79 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140140++0x03 line.long 0x00 "TSD2_SF_TARGETS_80,Targest 80 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140144++0x03 line.long 0x00 "TSD2_SF_TARGETS_81,Targest 81 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140148++0x03 line.long 0x00 "TSD2_SF_TARGETS_82,Targest 82 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14014C++0x03 line.long 0x00 "TSD2_SF_TARGETS_83,Targest 83 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140150++0x03 line.long 0x00 "TSD2_SF_TARGETS_84,Targest 84 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140154++0x03 line.long 0x00 "TSD2_SF_TARGETS_85,Targest 85 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140158++0x03 line.long 0x00 "TSD2_SF_TARGETS_86,Targest 86 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14015C++0x03 line.long 0x00 "TSD2_SF_TARGETS_87,Targest 87 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140160++0x03 line.long 0x00 "TSD2_SF_TARGETS_88,Targest 88 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140164++0x03 line.long 0x00 "TSD2_SF_TARGETS_89,Targest 89 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140168++0x03 line.long 0x00 "TSD2_SF_TARGETS_90,Targest 90 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14016C++0x03 line.long 0x00 "TSD2_SF_TARGETS_91,Targest 91 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140170++0x03 line.long 0x00 "TSD2_SF_TARGETS_92,Targest 92 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140174++0x03 line.long 0x00 "TSD2_SF_TARGETS_93,Targest 93 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140178++0x03 line.long 0x00 "TSD2_SF_TARGETS_94,Targest 94 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14017C++0x03 line.long 0x00 "TSD2_SF_TARGETS_95,Targest 95 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140180++0x03 line.long 0x00 "TSD2_SF_TARGETS_96,Targest 96 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140184++0x03 line.long 0x00 "TSD2_SF_TARGETS_97,Targest 97 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140188++0x03 line.long 0x00 "TSD2_SF_TARGETS_98,Targest 98 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14018C++0x03 line.long 0x00 "TSD2_SF_TARGETS_99,Targest 99 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140190++0x03 line.long 0x00 "TSD2_SF_TARGETS_100,Targest 100 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140194++0x03 line.long 0x00 "TSD2_SF_TARGETS_101,Targest 101 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140198++0x03 line.long 0x00 "TSD2_SF_TARGETS_102,Targest 102 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14019C++0x03 line.long 0x00 "TSD2_SF_TARGETS_103,Targest 103 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401A0++0x03 line.long 0x00 "TSD2_SF_TARGETS_104,Targest 104 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401A4++0x03 line.long 0x00 "TSD2_SF_TARGETS_105,Targest 105 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401A8++0x03 line.long 0x00 "TSD2_SF_TARGETS_106,Targest 106 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401AC++0x03 line.long 0x00 "TSD2_SF_TARGETS_107,Targest 107 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401B0++0x03 line.long 0x00 "TSD2_SF_TARGETS_108,Targest 108 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401B4++0x03 line.long 0x00 "TSD2_SF_TARGETS_109,Targest 109 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401B8++0x03 line.long 0x00 "TSD2_SF_TARGETS_110,Targest 110 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401BC++0x03 line.long 0x00 "TSD2_SF_TARGETS_111,Targest 111 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401C0++0x03 line.long 0x00 "TSD2_SF_TARGETS_112,Targest 112 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401C4++0x03 line.long 0x00 "TSD2_SF_TARGETS_113,Targest 113 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401C8++0x03 line.long 0x00 "TSD2_SF_TARGETS_114,Targest 114 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401CC++0x03 line.long 0x00 "TSD2_SF_TARGETS_115,Targest 115 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401D0++0x03 line.long 0x00 "TSD2_SF_TARGETS_116,Targest 116 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401D4++0x03 line.long 0x00 "TSD2_SF_TARGETS_117,Targest 117 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401D8++0x03 line.long 0x00 "TSD2_SF_TARGETS_118,Targest 118 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401DC++0x03 line.long 0x00 "TSD2_SF_TARGETS_119,Targest 119 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401E0++0x03 line.long 0x00 "TSD2_SF_TARGETS_120,Targest 120 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401E4++0x03 line.long 0x00 "TSD2_SF_TARGETS_121,Targest 121 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401E8++0x03 line.long 0x00 "TSD2_SF_TARGETS_122,Targest 122 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401EC++0x03 line.long 0x00 "TSD2_SF_TARGETS_123,Targest 123 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401F0++0x03 line.long 0x00 "TSD2_SF_TARGETS_124,Targest 124 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401F4++0x03 line.long 0x00 "TSD2_SF_TARGETS_125,Targest 125 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401F8++0x03 line.long 0x00 "TSD2_SF_TARGETS_126,Targest 126 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1401FC++0x03 line.long 0x00 "TSD2_SF_TARGETS_127,Targest 127 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140200++0x03 line.long 0x00 "TSD2_SF_TARGETS_128,Targest 128 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140204++0x03 line.long 0x00 "TSD2_SF_TARGETS_129,Targest 129 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140208++0x03 line.long 0x00 "TSD2_SF_TARGETS_130,Targest 130 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14020C++0x03 line.long 0x00 "TSD2_SF_TARGETS_131,Targest 131 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140210++0x03 line.long 0x00 "TSD2_SF_TARGETS_132,Targest 132 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140214++0x03 line.long 0x00 "TSD2_SF_TARGETS_133,Targest 133 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140218++0x03 line.long 0x00 "TSD2_SF_TARGETS_134,Targest 134 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14021C++0x03 line.long 0x00 "TSD2_SF_TARGETS_135,Targest 135 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140220++0x03 line.long 0x00 "TSD2_SF_TARGETS_136,Targest 136 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140224++0x03 line.long 0x00 "TSD2_SF_TARGETS_137,Targest 137 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140228++0x03 line.long 0x00 "TSD2_SF_TARGETS_138,Targest 138 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14022C++0x03 line.long 0x00 "TSD2_SF_TARGETS_139,Targest 139 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140230++0x03 line.long 0x00 "TSD2_SF_TARGETS_140,Targest 140 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140234++0x03 line.long 0x00 "TSD2_SF_TARGETS_141,Targest 141 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140238++0x03 line.long 0x00 "TSD2_SF_TARGETS_142,Targest 142 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14023C++0x03 line.long 0x00 "TSD2_SF_TARGETS_143,Targest 143 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140240++0x03 line.long 0x00 "TSD2_SF_TARGETS_144,Targest 144 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140244++0x03 line.long 0x00 "TSD2_SF_TARGETS_145,Targest 145 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140248++0x03 line.long 0x00 "TSD2_SF_TARGETS_146,Targest 146 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14024C++0x03 line.long 0x00 "TSD2_SF_TARGETS_147,Targest 147 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140250++0x03 line.long 0x00 "TSD2_SF_TARGETS_148,Targest 148 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140254++0x03 line.long 0x00 "TSD2_SF_TARGETS_149,Targest 149 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140258++0x03 line.long 0x00 "TSD2_SF_TARGETS_150,Targest 150 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14025C++0x03 line.long 0x00 "TSD2_SF_TARGETS_151,Targest 151 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140260++0x03 line.long 0x00 "TSD2_SF_TARGETS_152,Targest 152 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140264++0x03 line.long 0x00 "TSD2_SF_TARGETS_153,Targest 153 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140268++0x03 line.long 0x00 "TSD2_SF_TARGETS_154,Targest 154 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14026C++0x03 line.long 0x00 "TSD2_SF_TARGETS_155,Targest 155 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140270++0x03 line.long 0x00 "TSD2_SF_TARGETS_156,Targest 156 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140274++0x03 line.long 0x00 "TSD2_SF_TARGETS_157,Targest 157 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140278++0x03 line.long 0x00 "TSD2_SF_TARGETS_158,Targest 158 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14027C++0x03 line.long 0x00 "TSD2_SF_TARGETS_159,Targest 159 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140280++0x03 line.long 0x00 "TSD2_SF_TARGETS_160,Targest 160 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140284++0x03 line.long 0x00 "TSD2_SF_TARGETS_161,Targest 161 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140288++0x03 line.long 0x00 "TSD2_SF_TARGETS_162,Targest 162 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14028C++0x03 line.long 0x00 "TSD2_SF_TARGETS_163,Targest 163 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140290++0x03 line.long 0x00 "TSD2_SF_TARGETS_164,Targest 164 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140294++0x03 line.long 0x00 "TSD2_SF_TARGETS_165,Targest 165 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140298++0x03 line.long 0x00 "TSD2_SF_TARGETS_166,Targest 166 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14029C++0x03 line.long 0x00 "TSD2_SF_TARGETS_167,Targest 167 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402A0++0x03 line.long 0x00 "TSD2_SF_TARGETS_168,Targest 168 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402A4++0x03 line.long 0x00 "TSD2_SF_TARGETS_169,Targest 169 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402A8++0x03 line.long 0x00 "TSD2_SF_TARGETS_170,Targest 170 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402AC++0x03 line.long 0x00 "TSD2_SF_TARGETS_171,Targest 171 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402B0++0x03 line.long 0x00 "TSD2_SF_TARGETS_172,Targest 172 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402B4++0x03 line.long 0x00 "TSD2_SF_TARGETS_173,Targest 173 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402B8++0x03 line.long 0x00 "TSD2_SF_TARGETS_174,Targest 174 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402BC++0x03 line.long 0x00 "TSD2_SF_TARGETS_175,Targest 175 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402C0++0x03 line.long 0x00 "TSD2_SF_TARGETS_176,Targest 176 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402C4++0x03 line.long 0x00 "TSD2_SF_TARGETS_177,Targest 177 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402C8++0x03 line.long 0x00 "TSD2_SF_TARGETS_178,Targest 178 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402CC++0x03 line.long 0x00 "TSD2_SF_TARGETS_179,Targest 179 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402D0++0x03 line.long 0x00 "TSD2_SF_TARGETS_180,Targest 180 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402D4++0x03 line.long 0x00 "TSD2_SF_TARGETS_181,Targest 181 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402D8++0x03 line.long 0x00 "TSD2_SF_TARGETS_182,Targest 182 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402DC++0x03 line.long 0x00 "TSD2_SF_TARGETS_183,Targest 183 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402E0++0x03 line.long 0x00 "TSD2_SF_TARGETS_184,Targest 184 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402E4++0x03 line.long 0x00 "TSD2_SF_TARGETS_185,Targest 185 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402E8++0x03 line.long 0x00 "TSD2_SF_TARGETS_186,Targest 186 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402EC++0x03 line.long 0x00 "TSD2_SF_TARGETS_187,Targest 187 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402F0++0x03 line.long 0x00 "TSD2_SF_TARGETS_188,Targest 188 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402F4++0x03 line.long 0x00 "TSD2_SF_TARGETS_189,Targest 189 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402F8++0x03 line.long 0x00 "TSD2_SF_TARGETS_190,Targest 190 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1402FC++0x03 line.long 0x00 "TSD2_SF_TARGETS_191,Targest 191 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140300++0x03 line.long 0x00 "TSD2_SF_TARGETS_192,Targest 192 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140304++0x03 line.long 0x00 "TSD2_SF_TARGETS_193,Targest 193 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140308++0x03 line.long 0x00 "TSD2_SF_TARGETS_194,Targest 194 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14030C++0x03 line.long 0x00 "TSD2_SF_TARGETS_195,Targest 195 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140310++0x03 line.long 0x00 "TSD2_SF_TARGETS_196,Targest 196 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140314++0x03 line.long 0x00 "TSD2_SF_TARGETS_197,Targest 197 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140318++0x03 line.long 0x00 "TSD2_SF_TARGETS_198,Targest 198 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14031C++0x03 line.long 0x00 "TSD2_SF_TARGETS_199,Targest 199 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140320++0x03 line.long 0x00 "TSD2_SF_TARGETS_200,Targest 200 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140324++0x03 line.long 0x00 "TSD2_SF_TARGETS_201,Targest 201 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140328++0x03 line.long 0x00 "TSD2_SF_TARGETS_202,Targest 202 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14032C++0x03 line.long 0x00 "TSD2_SF_TARGETS_203,Targest 203 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140330++0x03 line.long 0x00 "TSD2_SF_TARGETS_204,Targest 204 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140334++0x03 line.long 0x00 "TSD2_SF_TARGETS_205,Targest 205 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140338++0x03 line.long 0x00 "TSD2_SF_TARGETS_206,Targest 206 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14033C++0x03 line.long 0x00 "TSD2_SF_TARGETS_207,Targest 207 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140340++0x03 line.long 0x00 "TSD2_SF_TARGETS_208,Targest 208 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140344++0x03 line.long 0x00 "TSD2_SF_TARGETS_209,Targest 209 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140348++0x03 line.long 0x00 "TSD2_SF_TARGETS_210,Targest 210 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14034C++0x03 line.long 0x00 "TSD2_SF_TARGETS_211,Targest 211 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140350++0x03 line.long 0x00 "TSD2_SF_TARGETS_212,Targest 212 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140354++0x03 line.long 0x00 "TSD2_SF_TARGETS_213,Targest 213 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140358++0x03 line.long 0x00 "TSD2_SF_TARGETS_214,Targest 214 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14035C++0x03 line.long 0x00 "TSD2_SF_TARGETS_215,Targest 215 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140360++0x03 line.long 0x00 "TSD2_SF_TARGETS_216,Targest 216 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140364++0x03 line.long 0x00 "TSD2_SF_TARGETS_217,Targest 217 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140368++0x03 line.long 0x00 "TSD2_SF_TARGETS_218,Targest 218 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14036C++0x03 line.long 0x00 "TSD2_SF_TARGETS_219,Targest 219 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140370++0x03 line.long 0x00 "TSD2_SF_TARGETS_220,Targest 220 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140374++0x03 line.long 0x00 "TSD2_SF_TARGETS_221,Targest 221 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140378++0x03 line.long 0x00 "TSD2_SF_TARGETS_222,Targest 222 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14037C++0x03 line.long 0x00 "TSD2_SF_TARGETS_223,Targest 223 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140380++0x03 line.long 0x00 "TSD2_SF_TARGETS_224,Targest 224 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140384++0x03 line.long 0x00 "TSD2_SF_TARGETS_225,Targest 225 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140388++0x03 line.long 0x00 "TSD2_SF_TARGETS_226,Targest 226 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14038C++0x03 line.long 0x00 "TSD2_SF_TARGETS_227,Targest 227 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140390++0x03 line.long 0x00 "TSD2_SF_TARGETS_228,Targest 228 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140394++0x03 line.long 0x00 "TSD2_SF_TARGETS_229,Targest 229 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x140398++0x03 line.long 0x00 "TSD2_SF_TARGETS_230,Targest 230 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x14039C++0x03 line.long 0x00 "TSD2_SF_TARGETS_231,Targest 231 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403A0++0x03 line.long 0x00 "TSD2_SF_TARGETS_232,Targest 232 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403A4++0x03 line.long 0x00 "TSD2_SF_TARGETS_233,Targest 233 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403A8++0x03 line.long 0x00 "TSD2_SF_TARGETS_234,Targest 234 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403AC++0x03 line.long 0x00 "TSD2_SF_TARGETS_235,Targest 235 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403B0++0x03 line.long 0x00 "TSD2_SF_TARGETS_236,Targest 236 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403B4++0x03 line.long 0x00 "TSD2_SF_TARGETS_237,Targest 237 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403B8++0x03 line.long 0x00 "TSD2_SF_TARGETS_238,Targest 238 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403BC++0x03 line.long 0x00 "TSD2_SF_TARGETS_239,Targest 239 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403C0++0x03 line.long 0x00 "TSD2_SF_TARGETS_240,Targest 240 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403C4++0x03 line.long 0x00 "TSD2_SF_TARGETS_241,Targest 241 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403C8++0x03 line.long 0x00 "TSD2_SF_TARGETS_242,Targest 242 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403CC++0x03 line.long 0x00 "TSD2_SF_TARGETS_243,Targest 243 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403D0++0x03 line.long 0x00 "TSD2_SF_TARGETS_244,Targest 244 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403D4++0x03 line.long 0x00 "TSD2_SF_TARGETS_245,Targest 245 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403D8++0x03 line.long 0x00 "TSD2_SF_TARGETS_246,Targest 246 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403DC++0x03 line.long 0x00 "TSD2_SF_TARGETS_247,Targest 247 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403E0++0x03 line.long 0x00 "TSD2_SF_TARGETS_248,Targest 248 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403E4++0x03 line.long 0x00 "TSD2_SF_TARGETS_249,Targest 249 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403E8++0x03 line.long 0x00 "TSD2_SF_TARGETS_250,Targest 250 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403EC++0x03 line.long 0x00 "TSD2_SF_TARGETS_251,Targest 251 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403F0++0x03 line.long 0x00 "TSD2_SF_TARGETS_252,Targest 252 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403F4++0x03 line.long 0x00 "TSD2_SF_TARGETS_253,Targest 253 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403F8++0x03 line.long 0x00 "TSD2_SF_TARGETS_254,Targest 254 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" wgroup.long 0x1403FC++0x03 line.long 0x00 "TSD2_SF_TARGETS_255,Targest 255 data" hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Section data expected" bitfld.long 0x00 23. " ENABLE0_7 ,Enables the Data0 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 22. " ENABLE0_6 ,Enables the Data0 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " ENABLE0_5 ,Enables the Data0 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 20. " ENABLE0_4 ,Enables the Data0 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 19. " ENABLE0_3 ,Enables the Data0 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " ENABLE0_2 ,Enables the Data0 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 17. " ENABLE0_1 ,Enables the Data0 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 16. " ENABLE0_0 ,Enables the Data0 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 8.--15. 1. " DATA1 ,Section data expected" bitfld.long 0x00 7. " ENABLE1_7 ,Enables the Data1 bit 7 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 6. " ENABLE1_6 ,Enables the Data1 bit 6 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " Enable1_5 ,Enables the Data1 bit 5 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 4. " ENABLE1_4 ,Enables the Data1 bit 4 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 3. " ENABLE1_3 ,Enables the Data1 bit 3 to be compared with the incoming section data bit" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " ENABLE1_2 ,Enables the Data1 bit 2 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 1. " ENABLE1_1 ,Enables the Data1 bit 1 to be compared with the incoming section data bit" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE1_0 ,Enables the Data1 bit 0 to be compared with the incoming section data bit" "Disabled,Enabled" tree.end tree.end width 17. tree "DEP Pointers" tree "TSD1" wgroup.long 0x40400++0x03 line.long 0x00 "TSD1_SF_PTR_0,DEP Pointer 0" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40404++0x03 line.long 0x00 "TSD1_SF_PTR_1,DEP Pointer 1" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40408++0x03 line.long 0x00 "TSD1_SF_PTR_2,DEP Pointer 2" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4040C++0x03 line.long 0x00 "TSD1_SF_PTR_3,DEP Pointer 3" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40410++0x03 line.long 0x00 "TSD1_SF_PTR_4,DEP Pointer 4" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40414++0x03 line.long 0x00 "TSD1_SF_PTR_5,DEP Pointer 5" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40418++0x03 line.long 0x00 "TSD1_SF_PTR_6,DEP Pointer 6" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4041C++0x03 line.long 0x00 "TSD1_SF_PTR_7,DEP Pointer 7" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40420++0x03 line.long 0x00 "TSD1_SF_PTR_8,DEP Pointer 8" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40424++0x03 line.long 0x00 "TSD1_SF_PTR_9,DEP Pointer 9" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40428++0x03 line.long 0x00 "TSD1_SF_PTR_10,DEP Pointer 10" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4042C++0x03 line.long 0x00 "TSD1_SF_PTR_11,DEP Pointer 11" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40430++0x03 line.long 0x00 "TSD1_SF_PTR_12,DEP Pointer 12" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40434++0x03 line.long 0x00 "TSD1_SF_PTR_13,DEP Pointer 13" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40438++0x03 line.long 0x00 "TSD1_SF_PTR_14,DEP Pointer 14" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4043C++0x03 line.long 0x00 "TSD1_SF_PTR_15,DEP Pointer 15" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40440++0x03 line.long 0x00 "TSD1_SF_PTR_16,DEP Pointer 16" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40444++0x03 line.long 0x00 "TSD1_SF_PTR_17,DEP Pointer 17" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40448++0x03 line.long 0x00 "TSD1_SF_PTR_18,DEP Pointer 18" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4044C++0x03 line.long 0x00 "TSD1_SF_PTR_19,DEP Pointer 19" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40450++0x03 line.long 0x00 "TSD1_SF_PTR_20,DEP Pointer 20" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40454++0x03 line.long 0x00 "TSD1_SF_PTR_21,DEP Pointer 21" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40458++0x03 line.long 0x00 "TSD1_SF_PTR_22,DEP Pointer 22" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4045C++0x03 line.long 0x00 "TSD1_SF_PTR_23,DEP Pointer 23" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40460++0x03 line.long 0x00 "TSD1_SF_PTR_24,DEP Pointer 24" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40464++0x03 line.long 0x00 "TSD1_SF_PTR_25,DEP Pointer 25" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40468++0x03 line.long 0x00 "TSD1_SF_PTR_26,DEP Pointer 26" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4046C++0x03 line.long 0x00 "TSD1_SF_PTR_27,DEP Pointer 27" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40470++0x03 line.long 0x00 "TSD1_SF_PTR_28,DEP Pointer 28" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40474++0x03 line.long 0x00 "TSD1_SF_PTR_29,DEP Pointer 29" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40478++0x03 line.long 0x00 "TSD1_SF_PTR_30,DEP Pointer 30" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4047C++0x03 line.long 0x00 "TSD1_SF_PTR_31,DEP Pointer 31" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40480++0x03 line.long 0x00 "TSD1_SF_PTR_32,DEP Pointer 32" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40484++0x03 line.long 0x00 "TSD1_SF_PTR_33,DEP Pointer 33" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40488++0x03 line.long 0x00 "TSD1_SF_PTR_34,DEP Pointer 34" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4048C++0x03 line.long 0x00 "TSD1_SF_PTR_35,DEP Pointer 35" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40490++0x03 line.long 0x00 "TSD1_SF_PTR_36,DEP Pointer 36" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40494++0x03 line.long 0x00 "TSD1_SF_PTR_37,DEP Pointer 37" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40498++0x03 line.long 0x00 "TSD1_SF_PTR_38,DEP Pointer 38" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4049C++0x03 line.long 0x00 "TSD1_SF_PTR_39,DEP Pointer 39" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404A0++0x03 line.long 0x00 "TSD1_SF_PTR_40,DEP Pointer 40" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404A4++0x03 line.long 0x00 "TSD1_SF_PTR_41,DEP Pointer 41" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404A8++0x03 line.long 0x00 "TSD1_SF_PTR_42,DEP Pointer 42" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404AC++0x03 line.long 0x00 "TSD1_SF_PTR_43,DEP Pointer 43" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404B0++0x03 line.long 0x00 "TSD1_SF_PTR_44,DEP Pointer 44" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404B4++0x03 line.long 0x00 "TSD1_SF_PTR_45,DEP Pointer 45" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404B8++0x03 line.long 0x00 "TSD1_SF_PTR_46,DEP Pointer 46" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404BC++0x03 line.long 0x00 "TSD1_SF_PTR_47,DEP Pointer 47" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404C0++0x03 line.long 0x00 "TSD1_SF_PTR_48,DEP Pointer 48" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404C4++0x03 line.long 0x00 "TSD1_SF_PTR_49,DEP Pointer 49" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404C8++0x03 line.long 0x00 "TSD1_SF_PTR_50,DEP Pointer 50" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404CC++0x03 line.long 0x00 "TSD1_SF_PTR_51,DEP Pointer 51" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404D0++0x03 line.long 0x00 "TSD1_SF_PTR_52,DEP Pointer 52" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404D4++0x03 line.long 0x00 "TSD1_SF_PTR_53,DEP Pointer 53" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404D8++0x03 line.long 0x00 "TSD1_SF_PTR_54,DEP Pointer 54" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404DC++0x03 line.long 0x00 "TSD1_SF_PTR_55,DEP Pointer 55" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404E0++0x03 line.long 0x00 "TSD1_SF_PTR_56,DEP Pointer 56" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404E4++0x03 line.long 0x00 "TSD1_SF_PTR_57,DEP Pointer 57" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404E8++0x03 line.long 0x00 "TSD1_SF_PTR_58,DEP Pointer 58" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404EC++0x03 line.long 0x00 "TSD1_SF_PTR_59,DEP Pointer 59" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404F0++0x03 line.long 0x00 "TSD1_SF_PTR_60,DEP Pointer 60" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404F4++0x03 line.long 0x00 "TSD1_SF_PTR_61,DEP Pointer 61" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404F8++0x03 line.long 0x00 "TSD1_SF_PTR_62,DEP Pointer 62" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x404FC++0x03 line.long 0x00 "TSD1_SF_PTR_63,DEP Pointer 63" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40500++0x03 line.long 0x00 "TSD1_SF_PTR_64,DEP Pointer 64" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40504++0x03 line.long 0x00 "TSD1_SF_PTR_65,DEP Pointer 65" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40508++0x03 line.long 0x00 "TSD1_SF_PTR_66,DEP Pointer 66" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4050C++0x03 line.long 0x00 "TSD1_SF_PTR_67,DEP Pointer 67" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40510++0x03 line.long 0x00 "TSD1_SF_PTR_68,DEP Pointer 68" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40514++0x03 line.long 0x00 "TSD1_SF_PTR_69,DEP Pointer 69" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40518++0x03 line.long 0x00 "TSD1_SF_PTR_70,DEP Pointer 70" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4051C++0x03 line.long 0x00 "TSD1_SF_PTR_71,DEP Pointer 71" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40520++0x03 line.long 0x00 "TSD1_SF_PTR_72,DEP Pointer 72" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40524++0x03 line.long 0x00 "TSD1_SF_PTR_73,DEP Pointer 73" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40528++0x03 line.long 0x00 "TSD1_SF_PTR_74,DEP Pointer 74" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4052C++0x03 line.long 0x00 "TSD1_SF_PTR_75,DEP Pointer 75" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40530++0x03 line.long 0x00 "TSD1_SF_PTR_76,DEP Pointer 76" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40534++0x03 line.long 0x00 "TSD1_SF_PTR_77,DEP Pointer 77" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40538++0x03 line.long 0x00 "TSD1_SF_PTR_78,DEP Pointer 78" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4053C++0x03 line.long 0x00 "TSD1_SF_PTR_79,DEP Pointer 79" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40540++0x03 line.long 0x00 "TSD1_SF_PTR_80,DEP Pointer 80" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40544++0x03 line.long 0x00 "TSD1_SF_PTR_81,DEP Pointer 81" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40548++0x03 line.long 0x00 "TSD1_SF_PTR_82,DEP Pointer 82" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4054C++0x03 line.long 0x00 "TSD1_SF_PTR_83,DEP Pointer 83" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40550++0x03 line.long 0x00 "TSD1_SF_PTR_84,DEP Pointer 84" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40554++0x03 line.long 0x00 "TSD1_SF_PTR_85,DEP Pointer 85" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40558++0x03 line.long 0x00 "TSD1_SF_PTR_86,DEP Pointer 86" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4055C++0x03 line.long 0x00 "TSD1_SF_PTR_87,DEP Pointer 87" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40560++0x03 line.long 0x00 "TSD1_SF_PTR_88,DEP Pointer 88" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40564++0x03 line.long 0x00 "TSD1_SF_PTR_89,DEP Pointer 89" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40568++0x03 line.long 0x00 "TSD1_SF_PTR_90,DEP Pointer 90" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4056C++0x03 line.long 0x00 "TSD1_SF_PTR_91,DEP Pointer 91" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40570++0x03 line.long 0x00 "TSD1_SF_PTR_92,DEP Pointer 92" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40574++0x03 line.long 0x00 "TSD1_SF_PTR_93,DEP Pointer 93" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40578++0x03 line.long 0x00 "TSD1_SF_PTR_94,DEP Pointer 94" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4057C++0x03 line.long 0x00 "TSD1_SF_PTR_95,DEP Pointer 95" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40580++0x03 line.long 0x00 "TSD1_SF_PTR_96,DEP Pointer 96" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40584++0x03 line.long 0x00 "TSD1_SF_PTR_97,DEP Pointer 97" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40588++0x03 line.long 0x00 "TSD1_SF_PTR_98,DEP Pointer 98" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4058C++0x03 line.long 0x00 "TSD1_SF_PTR_99,DEP Pointer 99" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40590++0x03 line.long 0x00 "TSD1_SF_PTR_100,DEP Pointer 100" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40594++0x03 line.long 0x00 "TSD1_SF_PTR_101,DEP Pointer 101" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x40598++0x03 line.long 0x00 "TSD1_SF_PTR_102,DEP Pointer 102" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x4059C++0x03 line.long 0x00 "TSD1_SF_PTR_103,DEP Pointer 103" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405A0++0x03 line.long 0x00 "TSD1_SF_PTR_104,DEP Pointer 104" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405A4++0x03 line.long 0x00 "TSD1_SF_PTR_105,DEP Pointer 105" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405A8++0x03 line.long 0x00 "TSD1_SF_PTR_106,DEP Pointer 106" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405AC++0x03 line.long 0x00 "TSD1_SF_PTR_107,DEP Pointer 107" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405B0++0x03 line.long 0x00 "TSD1_SF_PTR_108,DEP Pointer 108" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405B4++0x03 line.long 0x00 "TSD1_SF_PTR_109,DEP Pointer 109" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405B8++0x03 line.long 0x00 "TSD1_SF_PTR_110,DEP Pointer 110" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405BC++0x03 line.long 0x00 "TSD1_SF_PTR_111,DEP Pointer 111" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405C0++0x03 line.long 0x00 "TSD1_SF_PTR_112,DEP Pointer 112" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405C4++0x03 line.long 0x00 "TSD1_SF_PTR_113,DEP Pointer 113" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405C8++0x03 line.long 0x00 "TSD1_SF_PTR_114,DEP Pointer 114" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405CC++0x03 line.long 0x00 "TSD1_SF_PTR_115,DEP Pointer 115" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405D0++0x03 line.long 0x00 "TSD1_SF_PTR_116,DEP Pointer 116" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405D4++0x03 line.long 0x00 "TSD1_SF_PTR_117,DEP Pointer 117" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405D8++0x03 line.long 0x00 "TSD1_SF_PTR_118,DEP Pointer 118" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405DC++0x03 line.long 0x00 "TSD1_SF_PTR_119,DEP Pointer 119" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405E0++0x03 line.long 0x00 "TSD1_SF_PTR_120,DEP Pointer 120" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405E4++0x03 line.long 0x00 "TSD1_SF_PTR_121,DEP Pointer 121" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405E8++0x03 line.long 0x00 "TSD1_SF_PTR_122,DEP Pointer 122" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405EC++0x03 line.long 0x00 "TSD1_SF_PTR_123,DEP Pointer 123" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405F0++0x03 line.long 0x00 "TSD1_SF_PTR_124,DEP Pointer 124" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405F4++0x03 line.long 0x00 "TSD1_SF_PTR_125,DEP Pointer 125" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405F8++0x03 line.long 0x00 "TSD1_SF_PTR_126,DEP Pointer 126" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x405FC++0x03 line.long 0x00 "TSD1_SF_PTR_127,DEP Pointer 127" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" tree.end tree "TSD2" wgroup.long 0x140400++0x03 line.long 0x00 "TSD2_SF_PTR_0,DEP Pointer 0" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140404++0x03 line.long 0x00 "TSD2_SF_PTR_1,DEP Pointer 1" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140408++0x03 line.long 0x00 "TSD2_SF_PTR_2,DEP Pointer 2" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14040C++0x03 line.long 0x00 "TSD2_SF_PTR_3,DEP Pointer 3" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140410++0x03 line.long 0x00 "TSD2_SF_PTR_4,DEP Pointer 4" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140414++0x03 line.long 0x00 "TSD2_SF_PTR_5,DEP Pointer 5" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140418++0x03 line.long 0x00 "TSD2_SF_PTR_6,DEP Pointer 6" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14041C++0x03 line.long 0x00 "TSD2_SF_PTR_7,DEP Pointer 7" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140420++0x03 line.long 0x00 "TSD2_SF_PTR_8,DEP Pointer 8" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140424++0x03 line.long 0x00 "TSD2_SF_PTR_9,DEP Pointer 9" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140428++0x03 line.long 0x00 "TSD2_SF_PTR_10,DEP Pointer 10" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14042C++0x03 line.long 0x00 "TSD2_SF_PTR_11,DEP Pointer 11" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140430++0x03 line.long 0x00 "TSD2_SF_PTR_12,DEP Pointer 12" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140434++0x03 line.long 0x00 "TSD2_SF_PTR_13,DEP Pointer 13" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140438++0x03 line.long 0x00 "TSD2_SF_PTR_14,DEP Pointer 14" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14043C++0x03 line.long 0x00 "TSD2_SF_PTR_15,DEP Pointer 15" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140440++0x03 line.long 0x00 "TSD2_SF_PTR_16,DEP Pointer 16" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140444++0x03 line.long 0x00 "TSD2_SF_PTR_17,DEP Pointer 17" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140448++0x03 line.long 0x00 "TSD2_SF_PTR_18,DEP Pointer 18" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14044C++0x03 line.long 0x00 "TSD2_SF_PTR_19,DEP Pointer 19" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140450++0x03 line.long 0x00 "TSD2_SF_PTR_20,DEP Pointer 20" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140454++0x03 line.long 0x00 "TSD2_SF_PTR_21,DEP Pointer 21" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140458++0x03 line.long 0x00 "TSD2_SF_PTR_22,DEP Pointer 22" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14045C++0x03 line.long 0x00 "TSD2_SF_PTR_23,DEP Pointer 23" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140460++0x03 line.long 0x00 "TSD2_SF_PTR_24,DEP Pointer 24" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140464++0x03 line.long 0x00 "TSD2_SF_PTR_25,DEP Pointer 25" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140468++0x03 line.long 0x00 "TSD2_SF_PTR_26,DEP Pointer 26" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14046C++0x03 line.long 0x00 "TSD2_SF_PTR_27,DEP Pointer 27" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140470++0x03 line.long 0x00 "TSD2_SF_PTR_28,DEP Pointer 28" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140474++0x03 line.long 0x00 "TSD2_SF_PTR_29,DEP Pointer 29" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140478++0x03 line.long 0x00 "TSD2_SF_PTR_30,DEP Pointer 30" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14047C++0x03 line.long 0x00 "TSD2_SF_PTR_31,DEP Pointer 31" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140480++0x03 line.long 0x00 "TSD2_SF_PTR_32,DEP Pointer 32" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140484++0x03 line.long 0x00 "TSD2_SF_PTR_33,DEP Pointer 33" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140488++0x03 line.long 0x00 "TSD2_SF_PTR_34,DEP Pointer 34" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14048C++0x03 line.long 0x00 "TSD2_SF_PTR_35,DEP Pointer 35" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140490++0x03 line.long 0x00 "TSD2_SF_PTR_36,DEP Pointer 36" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140494++0x03 line.long 0x00 "TSD2_SF_PTR_37,DEP Pointer 37" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140498++0x03 line.long 0x00 "TSD2_SF_PTR_38,DEP Pointer 38" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14049C++0x03 line.long 0x00 "TSD2_SF_PTR_39,DEP Pointer 39" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404A0++0x03 line.long 0x00 "TSD2_SF_PTR_40,DEP Pointer 40" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404A4++0x03 line.long 0x00 "TSD2_SF_PTR_41,DEP Pointer 41" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404A8++0x03 line.long 0x00 "TSD2_SF_PTR_42,DEP Pointer 42" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404AC++0x03 line.long 0x00 "TSD2_SF_PTR_43,DEP Pointer 43" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404B0++0x03 line.long 0x00 "TSD2_SF_PTR_44,DEP Pointer 44" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404B4++0x03 line.long 0x00 "TSD2_SF_PTR_45,DEP Pointer 45" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404B8++0x03 line.long 0x00 "TSD2_SF_PTR_46,DEP Pointer 46" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404BC++0x03 line.long 0x00 "TSD2_SF_PTR_47,DEP Pointer 47" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404C0++0x03 line.long 0x00 "TSD2_SF_PTR_48,DEP Pointer 48" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404C4++0x03 line.long 0x00 "TSD2_SF_PTR_49,DEP Pointer 49" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404C8++0x03 line.long 0x00 "TSD2_SF_PTR_50,DEP Pointer 50" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404CC++0x03 line.long 0x00 "TSD2_SF_PTR_51,DEP Pointer 51" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404D0++0x03 line.long 0x00 "TSD2_SF_PTR_52,DEP Pointer 52" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404D4++0x03 line.long 0x00 "TSD2_SF_PTR_53,DEP Pointer 53" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404D8++0x03 line.long 0x00 "TSD2_SF_PTR_54,DEP Pointer 54" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404DC++0x03 line.long 0x00 "TSD2_SF_PTR_55,DEP Pointer 55" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404E0++0x03 line.long 0x00 "TSD2_SF_PTR_56,DEP Pointer 56" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404E4++0x03 line.long 0x00 "TSD2_SF_PTR_57,DEP Pointer 57" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404E8++0x03 line.long 0x00 "TSD2_SF_PTR_58,DEP Pointer 58" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404EC++0x03 line.long 0x00 "TSD2_SF_PTR_59,DEP Pointer 59" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404F0++0x03 line.long 0x00 "TSD2_SF_PTR_60,DEP Pointer 60" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404F4++0x03 line.long 0x00 "TSD2_SF_PTR_61,DEP Pointer 61" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404F8++0x03 line.long 0x00 "TSD2_SF_PTR_62,DEP Pointer 62" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1404FC++0x03 line.long 0x00 "TSD2_SF_PTR_63,DEP Pointer 63" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140500++0x03 line.long 0x00 "TSD2_SF_PTR_64,DEP Pointer 64" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140504++0x03 line.long 0x00 "TSD2_SF_PTR_65,DEP Pointer 65" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140508++0x03 line.long 0x00 "TSD2_SF_PTR_66,DEP Pointer 66" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14050C++0x03 line.long 0x00 "TSD2_SF_PTR_67,DEP Pointer 67" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140510++0x03 line.long 0x00 "TSD2_SF_PTR_68,DEP Pointer 68" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140514++0x03 line.long 0x00 "TSD2_SF_PTR_69,DEP Pointer 69" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140518++0x03 line.long 0x00 "TSD2_SF_PTR_70,DEP Pointer 70" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14051C++0x03 line.long 0x00 "TSD2_SF_PTR_71,DEP Pointer 71" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140520++0x03 line.long 0x00 "TSD2_SF_PTR_72,DEP Pointer 72" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140524++0x03 line.long 0x00 "TSD2_SF_PTR_73,DEP Pointer 73" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140528++0x03 line.long 0x00 "TSD2_SF_PTR_74,DEP Pointer 74" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14052C++0x03 line.long 0x00 "TSD2_SF_PTR_75,DEP Pointer 75" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140530++0x03 line.long 0x00 "TSD2_SF_PTR_76,DEP Pointer 76" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140534++0x03 line.long 0x00 "TSD2_SF_PTR_77,DEP Pointer 77" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140538++0x03 line.long 0x00 "TSD2_SF_PTR_78,DEP Pointer 78" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14053C++0x03 line.long 0x00 "TSD2_SF_PTR_79,DEP Pointer 79" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140540++0x03 line.long 0x00 "TSD2_SF_PTR_80,DEP Pointer 80" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140544++0x03 line.long 0x00 "TSD2_SF_PTR_81,DEP Pointer 81" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140548++0x03 line.long 0x00 "TSD2_SF_PTR_82,DEP Pointer 82" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14054C++0x03 line.long 0x00 "TSD2_SF_PTR_83,DEP Pointer 83" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140550++0x03 line.long 0x00 "TSD2_SF_PTR_84,DEP Pointer 84" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140554++0x03 line.long 0x00 "TSD2_SF_PTR_85,DEP Pointer 85" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140558++0x03 line.long 0x00 "TSD2_SF_PTR_86,DEP Pointer 86" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14055C++0x03 line.long 0x00 "TSD2_SF_PTR_87,DEP Pointer 87" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140560++0x03 line.long 0x00 "TSD2_SF_PTR_88,DEP Pointer 88" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140564++0x03 line.long 0x00 "TSD2_SF_PTR_89,DEP Pointer 89" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140568++0x03 line.long 0x00 "TSD2_SF_PTR_90,DEP Pointer 90" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14056C++0x03 line.long 0x00 "TSD2_SF_PTR_91,DEP Pointer 91" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140570++0x03 line.long 0x00 "TSD2_SF_PTR_92,DEP Pointer 92" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140574++0x03 line.long 0x00 "TSD2_SF_PTR_93,DEP Pointer 93" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140578++0x03 line.long 0x00 "TSD2_SF_PTR_94,DEP Pointer 94" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14057C++0x03 line.long 0x00 "TSD2_SF_PTR_95,DEP Pointer 95" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140580++0x03 line.long 0x00 "TSD2_SF_PTR_96,DEP Pointer 96" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140584++0x03 line.long 0x00 "TSD2_SF_PTR_97,DEP Pointer 97" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140588++0x03 line.long 0x00 "TSD2_SF_PTR_98,DEP Pointer 98" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14058C++0x03 line.long 0x00 "TSD2_SF_PTR_99,DEP Pointer 99" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140590++0x03 line.long 0x00 "TSD2_SF_PTR_100,DEP Pointer 100" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140594++0x03 line.long 0x00 "TSD2_SF_PTR_101,DEP Pointer 101" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x140598++0x03 line.long 0x00 "TSD2_SF_PTR_102,DEP Pointer 102" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x14059C++0x03 line.long 0x00 "TSD2_SF_PTR_103,DEP Pointer 103" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405A0++0x03 line.long 0x00 "TSD2_SF_PTR_104,DEP Pointer 104" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405A4++0x03 line.long 0x00 "TSD2_SF_PTR_105,DEP Pointer 105" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405A8++0x03 line.long 0x00 "TSD2_SF_PTR_106,DEP Pointer 106" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405AC++0x03 line.long 0x00 "TSD2_SF_PTR_107,DEP Pointer 107" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405B0++0x03 line.long 0x00 "TSD2_SF_PTR_108,DEP Pointer 108" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405B4++0x03 line.long 0x00 "TSD2_SF_PTR_109,DEP Pointer 109" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405B8++0x03 line.long 0x00 "TSD2_SF_PTR_110,DEP Pointer 110" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405BC++0x03 line.long 0x00 "TSD2_SF_PTR_111,DEP Pointer 111" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405C0++0x03 line.long 0x00 "TSD2_SF_PTR_112,DEP Pointer 112" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405C4++0x03 line.long 0x00 "TSD2_SF_PTR_113,DEP Pointer 113" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405C8++0x03 line.long 0x00 "TSD2_SF_PTR_114,DEP Pointer 114" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405CC++0x03 line.long 0x00 "TSD2_SF_PTR_115,DEP Pointer 115" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405D0++0x03 line.long 0x00 "TSD2_SF_PTR_116,DEP Pointer 116" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405D4++0x03 line.long 0x00 "TSD2_SF_PTR_117,DEP Pointer 117" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405D8++0x03 line.long 0x00 "TSD2_SF_PTR_118,DEP Pointer 118" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405DC++0x03 line.long 0x00 "TSD2_SF_PTR_119,DEP Pointer 119" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405E0++0x03 line.long 0x00 "TSD2_SF_PTR_120,DEP Pointer 120" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405E4++0x03 line.long 0x00 "TSD2_SF_PTR_121,DEP Pointer 121" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405E8++0x03 line.long 0x00 "TSD2_SF_PTR_122,DEP Pointer 122" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405EC++0x03 line.long 0x00 "TSD2_SF_PTR_123,DEP Pointer 123" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405F0++0x03 line.long 0x00 "TSD2_SF_PTR_124,DEP Pointer 124" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405F4++0x03 line.long 0x00 "TSD2_SF_PTR_125,DEP Pointer 125" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405F8++0x03 line.long 0x00 "TSD2_SF_PTR_126,DEP Pointer 126" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" wgroup.long 0x1405FC++0x03 line.long 0x00 "TSD2_SF_PTR_127,DEP Pointer 127" bitfld.long 0x00 7. " EOL ,The corresponding RAM line is the End of filter target" "Not EOL,EOL" hexmask.long.byte 0x00 0.--6. 1. " NXTDEPPTR ,The line number of next DEP" tree.end tree.end width 26. textline " " group.long 0x42000++0x03 line.long 0x00 "TSD1_SF_WAIT_FOR_BM,Wait or not for BM to store section before generating IRQ" bitfld.long 0x00 0. " VALUE ,Wait for BM" "Do not wait,Wait" group.long 0x42004++0xF "Debug Registers" line.long 0x0 "TSD1_SF_STARTED_CNT,Indicates how many times the section filter FSM is started" line.long 0x4 "TSD1_SF_CMP_STARTED_CNT,Indicates how many times the section comparator FSM is started" line.long 0x8 "TSD1_SF_CMP_FINISHED_CNT,Indicates how many times the section comparator FSM has finished successfully" line.long 0xC "TSD1_SEC_END_FOUND_CNT,Indicates how many complete section has been found" textline " " group.long 0x142000++0x03 line.long 0x00 "TSD2_SF_WAIT_FOR_BM,Wait or not for BM to store section before generating IRQ" bitfld.long 0x00 0. " VALUE ,Wait for BM" "Do not wait,Wait" group.long 0x142004++0xF "Debug Registers" line.long 0x0 "TSD2_SF_STARTED_CNT,Indicates how many times the section filter FSM is started" line.long 0x4 "TSD2_SF_CMP_STARTED_CNT,Indicates how many times the section comparator FSM is started" line.long 0x8 "TSD2_SF_CMP_FINISHED_CNT,Indicates how many times the section comparator FSM has finished successfully" line.long 0xC "TSD2_SEC_END_FOUND_CNT,Indicates how many complete section has been found" tree.end width 24. tree "PES Parser" group.long 0x470000++0x03 line.long 0x00 "TSD_PES0_CFG,Configuration register of PES parser" bitfld.long 0x00 22. " SEARCHAUDINHDR ,Indicates if AUD shall also be searched in PES packet header" "Not searched,Searched" bitfld.long 0x00 21. " HDRIRQENABLE ,Enables PES_HDR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 16.--20. " HDRBUF ,Specifies into which buffer the removed PES packet headers shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 15. " STOREHDR ,Enables PES packet header to be stored into the buffer specified with HdrBuf" "Disabled,Enabled" textline " " bitfld.long 0x00 14. " RMPADDINGSTREAM ,Indicates if padding stream shall be removed" "Not removed,Removed" bitfld.long 0x00 13. " PESPACKETSTARTIRQENABLE ,Enables PES_PACKET_START_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " STORERESIDUE ,This bit indicates if the residue from first PES packet shall be stored" "Not stored,Stored" bitfld.long 0x00 11. " KEEPSCRCTRL ,Scrambling control bits in packet header can be kept without being reset" "Reset,No reset" textline " " bitfld.long 0x00 9.--10. " INDEX ,Indicates in which TSD the bit group PidIndex is located" "0,1,2,3" bitfld.long 0x00 4.--8. " PIDINDEX ,Defines which PID channel shall be processed by this PES parser" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x00 3. " BYPASSPESDSC ,Indicates if PES level descrambler shall be bypassed" "Not bypassed,Baypassed" bitfld.long 0x00 2. " RMPESHEADER ,Remove PES packet header" "Not removed,Removed" textline " " bitfld.long 0x00 1. " PTSIRQENABLE ,PTS_IRQ enable" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE ,Enables this PES parser" "Disabled,Enabled" group.long 0x470004++0x03 line.long 0x00 "TSD_PES1_CFG,Configuration register of PES parser" bitfld.long 0x00 22. " SEARCHAUDINHDR ,Indicates if AUD shall also be searched in PES packet header" "Not searched,Searched" bitfld.long 0x00 21. " HDRIRQENABLE ,Enables PES_HDR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 16.--20. " HDRBUF ,Specifies into which buffer the removed PES packet headers shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 15. " STOREHDR ,Enables PES packet header to be stored into the buffer specified with HdrBuf" "Disabled,Enabled" textline " " bitfld.long 0x00 14. " RMPADDINGSTREAM ,Indicates if padding stream shall be removed" "Not removed,Removed" bitfld.long 0x00 13. " PESPACKETSTARTIRQENABLE ,Enables PES_PACKET_START_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " STORERESIDUE ,This bit indicates if the residue from first PES packet shall be stored" "Not stored,Stored" bitfld.long 0x00 11. " KEEPSCRCTRL ,Scrambling control bits in packet header can be kept without being reset" "Reset,No reset" textline " " bitfld.long 0x00 9.--10. " INDEX ,Indicates in which TSD the bit group PidIndex is located" "0,1,2,3" bitfld.long 0x00 4.--8. " PIDINDEX ,Defines which PID channel shall be processed by this PES parser" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x00 3. " BYPASSPESDSC ,Indicates if PES level descrambler shall be bypassed" "Not bypassed,Baypassed" bitfld.long 0x00 2. " RMPESHEADER ,Remove PES packet header" "Not removed,Removed" textline " " bitfld.long 0x00 1. " PTSIRQENABLE ,PTS_IRQ enable" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE ,Enables this PES parser" "Disabled,Enabled" group.long 0x470008++0x03 line.long 0x00 "TSD_PES2_CFG,Configuration register of PES parser" bitfld.long 0x00 22. " SEARCHAUDINHDR ,Indicates if AUD shall also be searched in PES packet header" "Not searched,Searched" bitfld.long 0x00 21. " HDRIRQENABLE ,Enables PES_HDR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 16.--20. " HDRBUF ,Specifies into which buffer the removed PES packet headers shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 15. " STOREHDR ,Enables PES packet header to be stored into the buffer specified with HdrBuf" "Disabled,Enabled" textline " " bitfld.long 0x00 14. " RMPADDINGSTREAM ,Indicates if padding stream shall be removed" "Not removed,Removed" bitfld.long 0x00 13. " PESPACKETSTARTIRQENABLE ,Enables PES_PACKET_START_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " STORERESIDUE ,This bit indicates if the residue from first PES packet shall be stored" "Not stored,Stored" bitfld.long 0x00 11. " KEEPSCRCTRL ,Scrambling control bits in packet header can be kept without being reset" "Reset,No reset" textline " " bitfld.long 0x00 9.--10. " INDEX ,Indicates in which TSD the bit group PidIndex is located" "0,1,2,3" bitfld.long 0x00 4.--8. " PIDINDEX ,Defines which PID channel shall be processed by this PES parser" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x00 3. " BYPASSPESDSC ,Indicates if PES level descrambler shall be bypassed" "Not bypassed,Baypassed" bitfld.long 0x00 2. " RMPESHEADER ,Remove PES packet header" "Not removed,Removed" textline " " bitfld.long 0x00 1. " PTSIRQENABLE ,PTS_IRQ enable" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE ,Enables this PES parser" "Disabled,Enabled" group.long 0x47000C++0x03 line.long 0x00 "TSD_PES3_CFG,Configuration register of PES parser" bitfld.long 0x00 22. " SEARCHAUDINHDR ,Indicates if AUD shall also be searched in PES packet header" "Not searched,Searched" bitfld.long 0x00 21. " HDRIRQENABLE ,Enables PES_HDR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 16.--20. " HDRBUF ,Specifies into which buffer the removed PES packet headers shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 15. " STOREHDR ,Enables PES packet header to be stored into the buffer specified with HdrBuf" "Disabled,Enabled" textline " " bitfld.long 0x00 14. " RMPADDINGSTREAM ,Indicates if padding stream shall be removed" "Not removed,Removed" bitfld.long 0x00 13. " PESPACKETSTARTIRQENABLE ,Enables PES_PACKET_START_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " STORERESIDUE ,This bit indicates if the residue from first PES packet shall be stored" "Not stored,Stored" bitfld.long 0x00 11. " KEEPSCRCTRL ,Scrambling control bits in packet header can be kept without being reset" "Reset,No reset" textline " " bitfld.long 0x00 9.--10. " INDEX ,Indicates in which TSD the bit group PidIndex is located" "0,1,2,3" bitfld.long 0x00 4.--8. " PIDINDEX ,Defines which PID channel shall be processed by this PES parser" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x00 3. " BYPASSPESDSC ,Indicates if PES level descrambler shall be bypassed" "Not bypassed,Baypassed" bitfld.long 0x00 2. " RMPESHEADER ,Remove PES packet header" "Not removed,Removed" textline " " bitfld.long 0x00 1. " PTSIRQENABLE ,PTS_IRQ enable" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE ,Enables this PES parser" "Disabled,Enabled" group.long 0x470010++0x03 line.long 0x00 "TSD_PES4_CFG,Configuration register of PES parser" bitfld.long 0x00 22. " SEARCHAUDINHDR ,Indicates if AUD shall also be searched in PES packet header" "Not searched,Searched" bitfld.long 0x00 21. " HDRIRQENABLE ,Enables PES_HDR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 16.--20. " HDRBUF ,Specifies into which buffer the removed PES packet headers shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 15. " STOREHDR ,Enables PES packet header to be stored into the buffer specified with HdrBuf" "Disabled,Enabled" textline " " bitfld.long 0x00 14. " RMPADDINGSTREAM ,Indicates if padding stream shall be removed" "Not removed,Removed" bitfld.long 0x00 13. " PESPACKETSTARTIRQENABLE ,Enables PES_PACKET_START_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " STORERESIDUE ,This bit indicates if the residue from first PES packet shall be stored" "Not stored,Stored" bitfld.long 0x00 11. " KEEPSCRCTRL ,Scrambling control bits in packet header can be kept without being reset" "Reset,No reset" textline " " bitfld.long 0x00 9.--10. " INDEX ,Indicates in which TSD the bit group PidIndex is located" "0,1,2,3" bitfld.long 0x00 4.--8. " PIDINDEX ,Defines which PID channel shall be processed by this PES parser" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x00 3. " BYPASSPESDSC ,Indicates if PES level descrambler shall be bypassed" "Not bypassed,Baypassed" bitfld.long 0x00 2. " RMPESHEADER ,Remove PES packet header" "Not removed,Removed" textline " " bitfld.long 0x00 1. " PTSIRQENABLE ,PTS_IRQ enable" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE ,Enables this PES parser" "Disabled,Enabled" group.long 0x470014++0x03 line.long 0x00 "TSD_PES5_CFG,Configuration register of PES parser" bitfld.long 0x00 22. " SEARCHAUDINHDR ,Indicates if AUD shall also be searched in PES packet header" "Not searched,Searched" bitfld.long 0x00 21. " HDRIRQENABLE ,Enables PES_HDR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 16.--20. " HDRBUF ,Specifies into which buffer the removed PES packet headers shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 15. " STOREHDR ,Enables PES packet header to be stored into the buffer specified with HdrBuf" "Disabled,Enabled" textline " " bitfld.long 0x00 14. " RMPADDINGSTREAM ,Indicates if padding stream shall be removed" "Not removed,Removed" bitfld.long 0x00 13. " PESPACKETSTARTIRQENABLE ,Enables PES_PACKET_START_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " STORERESIDUE ,This bit indicates if the residue from first PES packet shall be stored" "Not stored,Stored" bitfld.long 0x00 11. " KEEPSCRCTRL ,Scrambling control bits in packet header can be kept without being reset" "Reset,No reset" textline " " bitfld.long 0x00 9.--10. " INDEX ,Indicates in which TSD the bit group PidIndex is located" "0,1,2,3" bitfld.long 0x00 4.--8. " PIDINDEX ,Defines which PID channel shall be processed by this PES parser" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x00 3. " BYPASSPESDSC ,Indicates if PES level descrambler shall be bypassed" "Not bypassed,Baypassed" bitfld.long 0x00 2. " RMPESHEADER ,Remove PES packet header" "Not removed,Removed" textline " " bitfld.long 0x00 1. " PTSIRQENABLE ,PTS_IRQ enable" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE ,Enables this PES parser" "Disabled,Enabled" group.long 0x470018++0x03 line.long 0x00 "TSD_PES6_CFG,Configuration register of PES parser" bitfld.long 0x00 22. " SEARCHAUDINHDR ,Indicates if AUD shall also be searched in PES packet header" "Not searched,Searched" bitfld.long 0x00 21. " HDRIRQENABLE ,Enables PES_HDR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 16.--20. " HDRBUF ,Specifies into which buffer the removed PES packet headers shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 15. " STOREHDR ,Enables PES packet header to be stored into the buffer specified with HdrBuf" "Disabled,Enabled" textline " " bitfld.long 0x00 14. " RMPADDINGSTREAM ,Indicates if padding stream shall be removed" "Not removed,Removed" bitfld.long 0x00 13. " PESPACKETSTARTIRQENABLE ,Enables PES_PACKET_START_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " STORERESIDUE ,This bit indicates if the residue from first PES packet shall be stored" "Not stored,Stored" bitfld.long 0x00 11. " KEEPSCRCTRL ,Scrambling control bits in packet header can be kept without being reset" "Reset,No reset" textline " " bitfld.long 0x00 9.--10. " INDEX ,Indicates in which TSD the bit group PidIndex is located" "0,1,2,3" bitfld.long 0x00 4.--8. " PIDINDEX ,Defines which PID channel shall be processed by this PES parser" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x00 3. " BYPASSPESDSC ,Indicates if PES level descrambler shall be bypassed" "Not bypassed,Baypassed" bitfld.long 0x00 2. " RMPESHEADER ,Remove PES packet header" "Not removed,Removed" textline " " bitfld.long 0x00 1. " PTSIRQENABLE ,PTS_IRQ enable" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE ,Enables this PES parser" "Disabled,Enabled" group.long 0x47001C++0x03 line.long 0x00 "TSD_PES7_CFG,Configuration register of PES parser" bitfld.long 0x00 22. " SEARCHAUDINHDR ,Indicates if AUD shall also be searched in PES packet header" "Not searched,Searched" bitfld.long 0x00 21. " HDRIRQENABLE ,Enables PES_HDR_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 16.--20. " HDRBUF ,Specifies into which buffer the removed PES packet headers shall be stored" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 15. " STOREHDR ,Enables PES packet header to be stored into the buffer specified with HdrBuf" "Disabled,Enabled" textline " " bitfld.long 0x00 14. " RMPADDINGSTREAM ,Indicates if padding stream shall be removed" "Not removed,Removed" bitfld.long 0x00 13. " PESPACKETSTARTIRQENABLE ,Enables PES_PACKET_START_IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " STORERESIDUE ,This bit indicates if the residue from first PES packet shall be stored" "Not stored,Stored" bitfld.long 0x00 11. " KEEPSCRCTRL ,Scrambling control bits in packet header can be kept without being reset" "Reset,No reset" textline " " bitfld.long 0x00 9.--10. " INDEX ,Indicates in which TSD the bit group PidIndex is located" "0,1,2,3" bitfld.long 0x00 4.--8. " PIDINDEX ,Defines which PID channel shall be processed by this PES parser" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x00 3. " BYPASSPESDSC ,Indicates if PES level descrambler shall be bypassed" "Not bypassed,Baypassed" bitfld.long 0x00 2. " RMPESHEADER ,Remove PES packet header" "Not removed,Removed" textline " " bitfld.long 0x00 1. " PTSIRQENABLE ,PTS_IRQ enable" "Disabled,Enabled" bitfld.long 0x00 0. " ENABLE ,Enables this PES parser" "Disabled,Enabled" group.quad 0x470040++0x07 line.quad 0x00 "TSD_PES0_PTS,TSD_PES0_PTS" hexmask.quad 0x00 0.--32. 1. " VALUE ,The PTS value of PES parser 0" group.quad 0x470140++0x07 line.quad 0x00 "TSD_PES1_PTS,TSD_PES1_PTS" hexmask.quad 0x00 0.--32. 1. " VALUE ,The PTS value of PES parser 1" group.quad 0x470240++0x07 line.quad 0x00 "TSD_PES2_PTS,TSD_PES2_PTS" hexmask.quad 0x00 0.--32. 1. " VALUE ,The PTS value of PES parser 2" group.quad 0x470340++0x07 line.quad 0x00 "TSD_PES3_PTS,TSD_PES3_PTS" hexmask.quad 0x00 0.--32. 1. " VALUE ,The PTS value of PES parser 3" group.quad 0x470440++0x07 line.quad 0x00 "TSD_PES4_PTS,TSD_PES4_PTS" hexmask.quad 0x00 0.--32. 1. " VALUE ,The PTS value of PES parser 4" group.quad 0x470540++0x07 line.quad 0x00 "TSD_PES5_PTS,TSD_PES5_PTS" hexmask.quad 0x00 0.--32. 1. " VALUE ,The PTS value of PES parser 5" group.quad 0x470640++0x07 line.quad 0x00 "TSD_PES6_PTS,TSD_PES6_PTS" hexmask.quad 0x00 0.--32. 1. " VALUE ,The PTS value of PES parser 6" group.quad 0x470740++0x07 line.quad 0x00 "TSD_PES7_PTS,TSD_PES7_PTS" hexmask.quad 0x00 0.--32. 1. " VALUE ,The PTS value of PES parser 7" tree.end width 24. tree "TSD IRQ Controller" hgroup.long 0x460000++0x03 hide.long 0x00 "TSD_IRQ,TSD IRQ value" width 16. tree "TSD_IRQ_DBG" rgroup.long 0x460100++0x03 line.long 0x00 "TSD_IRQ_DBG_0,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460104++0x03 line.long 0x00 "TSD_IRQ_DBG_1,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460108++0x03 line.long 0x00 "TSD_IRQ_DBG_2,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x46010C++0x03 line.long 0x00 "TSD_IRQ_DBG_3,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460110++0x03 line.long 0x00 "TSD_IRQ_DBG_4,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460114++0x03 line.long 0x00 "TSD_IRQ_DBG_5,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460118++0x03 line.long 0x00 "TSD_IRQ_DBG_6,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x46011C++0x03 line.long 0x00 "TSD_IRQ_DBG_7,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460120++0x03 line.long 0x00 "TSD_IRQ_DBG_8,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460124++0x03 line.long 0x00 "TSD_IRQ_DBG_9,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460128++0x03 line.long 0x00 "TSD_IRQ_DBG_10,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x46012C++0x03 line.long 0x00 "TSD_IRQ_DBG_11,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460130++0x03 line.long 0x00 "TSD_IRQ_DBG_12,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460134++0x03 line.long 0x00 "TSD_IRQ_DBG_13,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460138++0x03 line.long 0x00 "TSD_IRQ_DBG_14,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x46013C++0x03 line.long 0x00 "TSD_IRQ_DBG_15,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460140++0x03 line.long 0x00 "TSD_IRQ_DBG_16,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460144++0x03 line.long 0x00 "TSD_IRQ_DBG_17,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460148++0x03 line.long 0x00 "TSD_IRQ_DBG_18,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x46014C++0x03 line.long 0x00 "TSD_IRQ_DBG_19,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460150++0x03 line.long 0x00 "TSD_IRQ_DBG_20,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460154++0x03 line.long 0x00 "TSD_IRQ_DBG_21,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460158++0x03 line.long 0x00 "TSD_IRQ_DBG_22,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x46015C++0x03 line.long 0x00 "TSD_IRQ_DBG_23,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460160++0x03 line.long 0x00 "TSD_IRQ_DBG_24,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460164++0x03 line.long 0x00 "TSD_IRQ_DBG_25,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460168++0x03 line.long 0x00 "TSD_IRQ_DBG_26,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x46016C++0x03 line.long 0x00 "TSD_IRQ_DBG_27,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460170++0x03 line.long 0x00 "TSD_IRQ_DBG_28,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460174++0x03 line.long 0x00 "TSD_IRQ_DBG_29,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460178++0x03 line.long 0x00 "TSD_IRQ_DBG_30,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x46017C++0x03 line.long 0x00 "TSD_IRQ_DBG_31,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460180++0x03 line.long 0x00 "TSD_IRQ_DBG_32,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460184++0x03 line.long 0x00 "TSD_IRQ_DBG_33,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460188++0x03 line.long 0x00 "TSD_IRQ_DBG_34,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x46018C++0x03 line.long 0x00 "TSD_IRQ_DBG_35,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460190++0x03 line.long 0x00 "TSD_IRQ_DBG_36,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460194++0x03 line.long 0x00 "TSD_IRQ_DBG_37,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x460198++0x03 line.long 0x00 "TSD_IRQ_DBG_38,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x46019C++0x03 line.long 0x00 "TSD_IRQ_DBG_39,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601A0++0x03 line.long 0x00 "TSD_IRQ_DBG_40,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601A4++0x03 line.long 0x00 "TSD_IRQ_DBG_41,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601A8++0x03 line.long 0x00 "TSD_IRQ_DBG_42,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601AC++0x03 line.long 0x00 "TSD_IRQ_DBG_43,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601B0++0x03 line.long 0x00 "TSD_IRQ_DBG_44,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601B4++0x03 line.long 0x00 "TSD_IRQ_DBG_45,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601B8++0x03 line.long 0x00 "TSD_IRQ_DBG_46,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601BC++0x03 line.long 0x00 "TSD_IRQ_DBG_47,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601C0++0x03 line.long 0x00 "TSD_IRQ_DBG_48,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601C4++0x03 line.long 0x00 "TSD_IRQ_DBG_49,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601C8++0x03 line.long 0x00 "TSD_IRQ_DBG_50,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601CC++0x03 line.long 0x00 "TSD_IRQ_DBG_51,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601D0++0x03 line.long 0x00 "TSD_IRQ_DBG_52,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601D4++0x03 line.long 0x00 "TSD_IRQ_DBG_53,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601D8++0x03 line.long 0x00 "TSD_IRQ_DBG_54,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601DC++0x03 line.long 0x00 "TSD_IRQ_DBG_55,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601E0++0x03 line.long 0x00 "TSD_IRQ_DBG_56,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601E4++0x03 line.long 0x00 "TSD_IRQ_DBG_57,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601E8++0x03 line.long 0x00 "TSD_IRQ_DBG_58,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601EC++0x03 line.long 0x00 "TSD_IRQ_DBG_59,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601F0++0x03 line.long 0x00 "TSD_IRQ_DBG_60,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601F4++0x03 line.long 0x00 "TSD_IRQ_DBG_61,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601F8++0x03 line.long 0x00 "TSD_IRQ_DBG_62,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" rgroup.long 0x4601FC++0x03 line.long 0x00 "TSD_IRQ_DBG_63,TSD IRQ debug value" bitfld.long 0x00 31. " FIFOOVF ,Indicates if this IRQ FIFO overflows" "Not overflow,Overflow" bitfld.long 0x00 30. " IRQAVAILABLE ,Indicates if IRQ is available" "Not available,Available" bitfld.long 0x00 29. " TRANSPORTERROR ,Indicates if IRQ is generated through a TS packet with transport error" "No error,Error" textline " " hexmask.long.word 0x00 13.--28. 1. " MISCELLANEOUS1 ,Miscellaneous1" bitfld.long 0x00 8.--12. " ID ,IRQ ID" "PACKET_END_IRQ,SECTION_END_IRQ,INPUT_TIMEOUT_IRQ,PID_TIMEOUT_IRQ,CONTINUITY_ERROR_IRQ,NEW_PCR_IRQ,PACKET_BUFFER_OVERFLOW,PUS_IRQ,PTS_IRQ,AF_PL_IRQ,TRANSPORT_ERROR_IRQ,DUPLICATE_IRQ,,PES_PACKET_START_IRQ,PES_HDR_IRQ,AF_END_IRQ,?..." hexmask.long.byte 0x00 0.--7. 1. " MISCELLANEOUS0 ,Miscellaneous0" tree.end width 24. textline " " wgroup.long 0x460400++0x03 line.long 0x00 "TSD_IRQ_FIFO_CLEAR,CLEAR IRQ FIFO" rgroup.long 0x460200++0x03 line.long 0x00 "TSD_IRQ_FIFO_RD_PTR,IRQ FIFO read pointer" hexmask.long.byte 0x00 0.--6. 1. " VALUE ,The read pointer of the IRQ FIFO" rgroup.long 0x460300++0x03 line.long 0x00 "TSD_IRQ_FIFO_WR_PTR,IRQ FIFO write pointer" hexmask.long.byte 0x00 0.--6. 1. " VALUE ,The write pointer of the IRQ FIFO" rgroup.long 0x460500++0x03 line.long 0x00 "TSD_IRQ_FIFO_FLAG,IRQ FIFO flag" bitfld.long 0x00 2. " OVERFLOW ,FIFO overflow flag" "Not overflow,Overflow" bitfld.long 0x00 1. " FULL ,FIFO full flag" "Not full,Full" textline " " bitfld.long 0x00 0. " EMPTY ,FIFO empty flag" "Not empty,Empty" group.long 0x470048++0x03 line.long 0x00 "TSD_PES0_LENGTH_OFFSET,TSD_PES0_LENGTH_OFFSET" bitfld.long 0x00 18. " PACKETLENGTH-Defined ,Indicates if the PES packet length if defined" "Not defined,Defined" bitfld.long 0x00 17. " UPPERLENGTHVALID ,Indicates if the upper half (bit[15:8]) of the bit group VALUE is valid" "Invalid,Valid" textline " " bitfld.long 0x00 16. " LOWERLENGTHVALID ,Indicates if the lower half (bit[7:0]) of the bit group VALUE is valid" "Invalid,Valid" hexmask.long.word 0x00 0.--15. 1. " VALUE ,The PES packet length offset" group.long 0x470148++0x03 line.long 0x00 "TSD_PES1_LENGTH_OFFSET,TSD_PES1_LENGTH_OFFSET" bitfld.long 0x00 18. " PACKETLENGTH-Defined ,Indicates if the PES packet length if defined" "Not defined,Defined" bitfld.long 0x00 17. " UPPERLENGTHVALID ,Indicates if the upper half (bit[15:8]) of the bit group VALUE is valid" "Invalid,Valid" textline " " bitfld.long 0x00 16. " LOWERLENGTHVALID ,Indicates if the lower half (bit[7:0]) of the bit group VALUE is valid" "Invalid,Valid" hexmask.long.word 0x00 0.--15. 1. " VALUE ,The PES packet length offset" group.long 0x470248++0x03 line.long 0x00 "TSD_PES2_LENGTH_OFFSET,TSD_PES2_LENGTH_OFFSET" bitfld.long 0x00 18. " PACKETLENGTH-Defined ,Indicates if the PES packet length if defined" "Not defined,Defined" bitfld.long 0x00 17. " UPPERLENGTHVALID ,Indicates if the upper half (bit[15:8]) of the bit group VALUE is valid" "Invalid,Valid" textline " " bitfld.long 0x00 16. " LOWERLENGTHVALID ,Indicates if the lower half (bit[7:0]) of the bit group VALUE is valid" "Invalid,Valid" hexmask.long.word 0x00 0.--15. 1. " VALUE ,The PES packet length offset" group.long 0x470348++0x03 line.long 0x00 "TSD_PES3_LENGTH_OFFSET,TSD_PES3_LENGTH_OFFSET" bitfld.long 0x00 18. " PACKETLENGTH-Defined ,Indicates if the PES packet length if defined" "Not defined,Defined" bitfld.long 0x00 17. " UPPERLENGTHVALID ,Indicates if the upper half (bit[15:8]) of the bit group VALUE is valid" "Invalid,Valid" textline " " bitfld.long 0x00 16. " LOWERLENGTHVALID ,Indicates if the lower half (bit[7:0]) of the bit group VALUE is valid" "Invalid,Valid" hexmask.long.word 0x00 0.--15. 1. " VALUE ,The PES packet length offset" group.long 0x470448++0x03 line.long 0x00 "TSD_PES4_LENGTH_OFFSET,TSD_PES4_LENGTH_OFFSET" bitfld.long 0x00 18. " PACKETLENGTH-Defined ,Indicates if the PES packet length if defined" "Not defined,Defined" bitfld.long 0x00 17. " UPPERLENGTHVALID ,Indicates if the upper half (bit[15:8]) of the bit group VALUE is valid" "Invalid,Valid" textline " " bitfld.long 0x00 16. " LOWERLENGTHVALID ,Indicates if the lower half (bit[7:0]) of the bit group VALUE is valid" "Invalid,Valid" hexmask.long.word 0x00 0.--15. 1. " VALUE ,The PES packet length offset" group.long 0x470548++0x03 line.long 0x00 "TSD_PES5_LENGTH_OFFSET,TSD_PES5_LENGTH_OFFSET" bitfld.long 0x00 18. " PACKETLENGTH-Defined ,Indicates if the PES packet length if defined" "Not defined,Defined" bitfld.long 0x00 17. " UPPERLENGTHVALID ,Indicates if the upper half (bit[15:8]) of the bit group VALUE is valid" "Invalid,Valid" textline " " bitfld.long 0x00 16. " LOWERLENGTHVALID ,Indicates if the lower half (bit[7:0]) of the bit group VALUE is valid" "Invalid,Valid" hexmask.long.word 0x00 0.--15. 1. " VALUE ,The PES packet length offset" group.long 0x470648++0x03 line.long 0x00 "TSD_PES6_LENGTH_OFFSET,TSD_PES6_LENGTH_OFFSET" bitfld.long 0x00 18. " PACKETLENGTH-Defined ,Indicates if the PES packet length if defined" "Not defined,Defined" bitfld.long 0x00 17. " UPPERLENGTHVALID ,Indicates if the upper half (bit[15:8]) of the bit group VALUE is valid" "Invalid,Valid" textline " " bitfld.long 0x00 16. " LOWERLENGTHVALID ,Indicates if the lower half (bit[7:0]) of the bit group VALUE is valid" "Invalid,Valid" hexmask.long.word 0x00 0.--15. 1. " VALUE ,The PES packet length offset" group.long 0x470748++0x03 line.long 0x00 "TSD_PES7_LENGTH_OFFSET,TSD_PES7_LENGTH_OFFSET" bitfld.long 0x00 18. " PACKETLENGTH-Defined ,Indicates if the PES packet length if defined" "Not defined,Defined" bitfld.long 0x00 17. " UPPERLENGTHVALID ,Indicates if the upper half (bit[15:8]) of the bit group VALUE is valid" "Invalid,Valid" textline " " bitfld.long 0x00 16. " LOWERLENGTHVALID ,Indicates if the lower half (bit[7:0]) of the bit group VALUE is valid" "Invalid,Valid" hexmask.long.word 0x00 0.--15. 1. " VALUE ,The PES packet length offset" if (((per.l(ad:0xC0000000+0x90+0x10))&0x30)==0x10) group.long 0x90++0x3 line.long 0x0 "TSD1_TRANSPORT_ERR_CFG,Transport error configuration" hexmask.long.byte 0x0 12.--19. 1. " COUNTER_START_VALUE ,The start value of transport error counter" bitfld.long 0x0 8. " RM_PACKET ,To configure if TS packet with transport error shall be removed" "Not removed,Removed" bitfld.long 0x0 4.--5. " IRQ_MODE ,Defines the transport error IRQ generation mode" "Flag,CNT,PID," textline " " bitfld.long 0x0 1. " IVSELECTMODE ,Specify the AES/MULTI2 Initial Vector selection mode (SklySelector with odd/even flag or without)" "Odd/Even flag,No Odd/Even flag" bitfld.long 0x0 0. " IRQ_ENABLE ,Enables transport error IRQ" "Disabled,Enabled" else group.long 0x90++0x3 line.long 0x0 "TSD1_TRANSPORT_ERR_CFG,Transport error configuration" bitfld.long 0x0 8. " RM_PACKET ,To configure if TS packet with transport error shall be removed" "Not removed,Removed" bitfld.long 0x0 4.--5. " IRQ_MODE ,Defines the transport error IRQ generation mode" "Flag,CNT,PID," textline " " bitfld.long 0x0 1. " IVSELECTMODE ,Specify the AES/MULTI2 Initial Vector selection mode (SklySelector with odd/even flag or without)" "Odd/Even flag,No Odd/Even flag" bitfld.long 0x0 0. " IRQ_ENABLE ,Enables transport error IRQ" "Disabled,Enabled" endif if (((per.l(ad:0xC0000000+0x100090+0x10))&0x30)==0x10) group.long 0x100090++0x3 line.long 0x0 "TSD2_TRANSPORT_ERR_CFG,Transport error configuration" hexmask.long.byte 0x0 12.--19. 1. " COUNTER_START_VALUE ,The start value of transport error counter" bitfld.long 0x0 8. " RM_PACKET ,To configure if TS packet with transport error shall be removed" "Not removed,Removed" bitfld.long 0x0 4.--5. " IRQ_MODE ,Defines the transport error IRQ generation mode" "Flag,CNT,PID," textline " " bitfld.long 0x0 1. " IVSELECTMODE ,Specify the AES/MULTI2 Initial Vector selection mode (SklySelector with odd/even flag or without)" "Odd/Even flag,No Odd/Even flag" bitfld.long 0x0 0. " IRQ_ENABLE ,Enables transport error IRQ" "Disabled,Enabled" else group.long 0x100090++0x3 line.long 0x0 "TSD2_TRANSPORT_ERR_CFG,Transport error configuration" bitfld.long 0x0 8. " RM_PACKET ,To configure if TS packet with transport error shall be removed" "Not removed,Removed" bitfld.long 0x0 4.--5. " IRQ_MODE ,Defines the transport error IRQ generation mode" "Flag,CNT,PID," textline " " bitfld.long 0x0 1. " IVSELECTMODE ,Specify the AES/MULTI2 Initial Vector selection mode (SklySelector with odd/even flag or without)" "Odd/Even flag,No Odd/Even flag" bitfld.long 0x0 0. " IRQ_ENABLE ,Enables transport error IRQ" "Disabled,Enabled" endif width 23. tree "TSD_PID_TIMEOUT_CFG" group.long 0x400240++0x3 line.long 0x00 "TSD_PID_TIMEOUT_CFG0,PID timeout counter" hexmask.long.tbyte 0x00 8.--31. 1. " CNTVALUE ,CntValue" bitfld.long 0x00 7. " ENABLE ,Enables the PID timeout counter and PID timeout IRQ" "Disabled,Enabled" bitfld.long 0x00 5.--6. " INDEX ,Indicates for which TSD the PID timeout is configured" "0,1,2,3" bitfld.long 0x00 0.--4. " PIDINDEX ,Indicates for which PID channel the PID timeout is configured" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x400244++0x3 line.long 0x00 "TSD_PID_TIMEOUT_CFG1,PID timeout counter" hexmask.long.tbyte 0x00 8.--31. 1. " CNTVALUE ,CntValue" bitfld.long 0x00 7. " ENABLE ,Enables the PID timeout counter and PID timeout IRQ" "Disabled,Enabled" bitfld.long 0x00 5.--6. " INDEX ,Indicates for which TSD the PID timeout is configured" "0,1,2,3" bitfld.long 0x00 0.--4. " PIDINDEX ,Indicates for which PID channel the PID timeout is configured" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x400248++0x3 line.long 0x00 "TSD_PID_TIMEOUT_CFG2,PID timeout counter" hexmask.long.tbyte 0x00 8.--31. 1. " CNTVALUE ,CntValue" bitfld.long 0x00 7. " ENABLE ,Enables the PID timeout counter and PID timeout IRQ" "Disabled,Enabled" bitfld.long 0x00 5.--6. " INDEX ,Indicates for which TSD the PID timeout is configured" "0,1,2,3" bitfld.long 0x00 0.--4. " PIDINDEX ,Indicates for which PID channel the PID timeout is configured" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x40024C++0x3 line.long 0x00 "TSD_PID_TIMEOUT_CFG3,PID timeout counter" hexmask.long.tbyte 0x00 8.--31. 1. " CNTVALUE ,CntValue" bitfld.long 0x00 7. " ENABLE ,Enables the PID timeout counter and PID timeout IRQ" "Disabled,Enabled" bitfld.long 0x00 5.--6. " INDEX ,Indicates for which TSD the PID timeout is configured" "0,1,2,3" bitfld.long 0x00 0.--4. " PIDINDEX ,Indicates for which PID channel the PID timeout is configured" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x400250++0x3 line.long 0x00 "TSD_PID_TIMEOUT_CFG4,PID timeout counter" hexmask.long.tbyte 0x00 8.--31. 1. " CNTVALUE ,CntValue" bitfld.long 0x00 7. " ENABLE ,Enables the PID timeout counter and PID timeout IRQ" "Disabled,Enabled" bitfld.long 0x00 5.--6. " INDEX ,Indicates for which TSD the PID timeout is configured" "0,1,2,3" bitfld.long 0x00 0.--4. " PIDINDEX ,Indicates for which PID channel the PID timeout is configured" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x400254++0x3 line.long 0x00 "TSD_PID_TIMEOUT_CFG5,PID timeout counter" hexmask.long.tbyte 0x00 8.--31. 1. " CNTVALUE ,CntValue" bitfld.long 0x00 7. " ENABLE ,Enables the PID timeout counter and PID timeout IRQ" "Disabled,Enabled" bitfld.long 0x00 5.--6. " INDEX ,Indicates for which TSD the PID timeout is configured" "0,1,2,3" bitfld.long 0x00 0.--4. " PIDINDEX ,Indicates for which PID channel the PID timeout is configured" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x400258++0x3 line.long 0x00 "TSD_PID_TIMEOUT_CFG6,PID timeout counter" hexmask.long.tbyte 0x00 8.--31. 1. " CNTVALUE ,CntValue" bitfld.long 0x00 7. " ENABLE ,Enables the PID timeout counter and PID timeout IRQ" "Disabled,Enabled" bitfld.long 0x00 5.--6. " INDEX ,Indicates for which TSD the PID timeout is configured" "0,1,2,3" bitfld.long 0x00 0.--4. " PIDINDEX ,Indicates for which PID channel the PID timeout is configured" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x40025C++0x3 line.long 0x00 "TSD_PID_TIMEOUT_CFG7,PID timeout counter" hexmask.long.tbyte 0x00 8.--31. 1. " CNTVALUE ,CntValue" bitfld.long 0x00 7. " ENABLE ,Enables the PID timeout counter and PID timeout IRQ" "Disabled,Enabled" bitfld.long 0x00 5.--6. " INDEX ,Indicates for which TSD the PID timeout is configured" "0,1,2,3" bitfld.long 0x00 0.--4. " PIDINDEX ,Indicates for which PID channel the PID timeout is configured" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x400260++0x3 line.long 0x00 "TSD_PID_TIMEOUT_CFG8,PID timeout counter" hexmask.long.tbyte 0x00 8.--31. 1. " CNTVALUE ,CntValue" bitfld.long 0x00 7. " ENABLE ,Enables the PID timeout counter and PID timeout IRQ" "Disabled,Enabled" bitfld.long 0x00 5.--6. " INDEX ,Indicates for which TSD the PID timeout is configured" "0,1,2,3" bitfld.long 0x00 0.--4. " PIDINDEX ,Indicates for which PID channel the PID timeout is configured" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x400264++0x3 line.long 0x00 "TSD_PID_TIMEOUT_CFG9,PID timeout counter" hexmask.long.tbyte 0x00 8.--31. 1. " CNTVALUE ,CntValue" bitfld.long 0x00 7. " ENABLE ,Enables the PID timeout counter and PID timeout IRQ" "Disabled,Enabled" bitfld.long 0x00 5.--6. " INDEX ,Indicates for which TSD the PID timeout is configured" "0,1,2,3" bitfld.long 0x00 0.--4. " PIDINDEX ,Indicates for which PID channel the PID timeout is configured" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x400268++0x3 line.long 0x00 "TSD_PID_TIMEOUT_CFG10,PID timeout counter" hexmask.long.tbyte 0x00 8.--31. 1. " CNTVALUE ,CntValue" bitfld.long 0x00 7. " ENABLE ,Enables the PID timeout counter and PID timeout IRQ" "Disabled,Enabled" bitfld.long 0x00 5.--6. " INDEX ,Indicates for which TSD the PID timeout is configured" "0,1,2,3" bitfld.long 0x00 0.--4. " PIDINDEX ,Indicates for which PID channel the PID timeout is configured" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x40026C++0x3 line.long 0x00 "TSD_PID_TIMEOUT_CFG11,PID timeout counter" hexmask.long.tbyte 0x00 8.--31. 1. " CNTVALUE ,CntValue" bitfld.long 0x00 7. " ENABLE ,Enables the PID timeout counter and PID timeout IRQ" "Disabled,Enabled" bitfld.long 0x00 5.--6. " INDEX ,Indicates for which TSD the PID timeout is configured" "0,1,2,3" bitfld.long 0x00 0.--4. " PIDINDEX ,Indicates for which PID channel the PID timeout is configured" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" tree.end textline " " width 37. group.long 0xA8++0x23 line.long 0x00 "TSD1_CSA21_CONFORMANCE,Indicate if CSA descrambler shall activate its conformance mechanism" line.long 0x04 "TSD1_AES_IV_31_0,Bits [31:0] of AES Initial Vector" line.long 0x08 "TSD1_AES_IV_63_32,Bits [63:32] of AES Initial Vector" line.long 0x0C "TSD1_AES_IV_95_64,Bits [95:64] of AES Initial Vector" line.long 0x10 "TSD1_AES_IV_127_96,Bits [127:96] of AES Initial Vector" line.long 0x14 "TSD1_INPUT_TIMEOUT,Max timeout between two input packets" line.long 0x1C "TSD1_INPUT_TIMEOUT_IRQ_ENABLE,Enables input timeout IRQ of TSD 1" bitfld.long 0x1C 0. " VALUE ,Enables input timeout IRQ" "Disabled,Enabled" line.long 0x18 "TSD1_VALID_INPUT_TIMEOUT,Max timeout between two valid input packets" line.long 0x20 "TSD1_VALID_INPUT_TIMEOUT_IRQ_ENABLE,Enables valid input timeout IRQ of TSD 1" bitfld.long 0x20 0. " VALUE ,Enables valid input timeout IRQ" "Disabled,Enabled" group.long 0x1000A8++0x23 line.long 0x00 "TSD2_CSA21_CONFORMANCE,Indicate if CSA descrambler shall activate its conformance mechanism" line.long 0x04 "TSD2_AES_IV_31_0,Bits [31:0] of AES Initial Vector" line.long 0x08 "TSD2_AES_IV_63_32,Bits [63:32] of AES Initial Vector" line.long 0x0C "TSD2_AES_IV_95_64,Bits [95:64] of AES Initial Vector" line.long 0x10 "TSD2_AES_IV_127_96,Bits [127:96] of AES Initial Vector" line.long 0x14 "TSD2_INPUT_TIMEOUT,Max timeout between two input packets" line.long 0x1C "TSD2_INPUT_TIMEOUT_IRQ_ENABLE,Enables input timeout IRQ of TSD 2" bitfld.long 0x1C 0. " VALUE ,Enables input timeout IRQ" "Disabled,Enabled" line.long 0x18 "TSD2_VALID_INPUT_TIMEOUT,Max timeout between two valid input packets" line.long 0x20 "TSD2_VALID_INPUT_TIMEOUT_IRQ_ENABLE,Enables valid input timeout IRQ of TSD 2" bitfld.long 0x20 0. " VALUE ,Enables valid input timeout IRQ" "Disabled,Enabled" tree.end width 15. tree "Reset FSMs in TDS" group.long 0x400218++0x03 line.long 0x00 "TSD_RESET_FSM,Reset FSMs in TSD" bitfld.long 0x00 0. " VALUE ,Reset all FSMs in TSD" "No reset,Reset" rgroup.long 0x40021C++0x03 line.long 0x00 "TSD_FSM_STATE,Hardware debug register" bitfld.long 0x00 29.--30. " PES ,PES parser state" "0,1,2,3" bitfld.long 0x00 24.--26. " BMAXIRD ,Buffer manager AXI bus read state" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 20.--23. " BMINBUFRD ,Buffer manager input buffer read state" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 16.--19. " BMAXIWR ,Buffer manager AXI bus write state" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 13.--15. " SB ,Section buffer state" "0,1,2,3,4,5,6,7" bitfld.long 0x00 8.--12. " PACKETPARSER ,Packet parser state" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x00 4.--7. " SF ,Section filter state" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 0.--3. " SFCMP ,Section filter comparison state" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" tree.end width 16. tree "Base Address" group.long 0x50100++0x03 line.long 0x00 "BM0_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50104++0x03 line.long 0x00 "BM1_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50108++0x03 line.long 0x00 "BM2_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x5010C++0x03 line.long 0x00 "BM3_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50110++0x03 line.long 0x00 "BM4_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50114++0x03 line.long 0x00 "BM5_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50118++0x03 line.long 0x00 "BM6_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x5011C++0x03 line.long 0x00 "BM7_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50120++0x03 line.long 0x00 "BM8_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50124++0x03 line.long 0x00 "BM9_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50128++0x03 line.long 0x00 "BM10_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x5012C++0x03 line.long 0x00 "BM11_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50130++0x03 line.long 0x00 "BM12_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50134++0x03 line.long 0x00 "BM13_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50138++0x03 line.long 0x00 "BM14_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x5013C++0x03 line.long 0x00 "BM15_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50140++0x03 line.long 0x00 "BM16_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50144++0x03 line.long 0x00 "BM17_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50148++0x03 line.long 0x00 "BM18_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x5014C++0x03 line.long 0x00 "BM19_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50150++0x03 line.long 0x00 "BM20_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50154++0x03 line.long 0x00 "BM21_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50158++0x03 line.long 0x00 "BM22_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x5015C++0x03 line.long 0x00 "BM23_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50160++0x03 line.long 0x00 "BM24_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50164++0x03 line.long 0x00 "BM25_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50168++0x03 line.long 0x00 "BM26_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x5016C++0x03 line.long 0x00 "BM27_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50170++0x03 line.long 0x00 "BM28_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50174++0x03 line.long 0x00 "BM29_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x50178++0x03 line.long 0x00 "BM30_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" group.long 0x5017C++0x03 line.long 0x00 "BM31_BASE_ADDR,Buffer start address" hexmask.long 0x00 10.--30. 0x400 " VALUE ,Buffer base address can only be set in steps of 1K bytes" tree.end width 23. tree "Global Offset" group.long 0x5029C++0x03 line.long 0x00 "BM1_GLOBAL_OFFSET,BM1 global ofset" bitfld.long 0x00 0. " VALUE ,The global offset for BM1" "If 0x0,If 0x80000000" group.long 0x15029C++0x03 line.long 0x00 "BM2_GLOBAL_OFFSET,BM2 global ofset" bitfld.long 0x00 0. " VALUE ,The global offset for BM2" "If 0x0,If 0x80000000" width 17. tree "BUF_SIZE" tree "BM1" group.long 0x50000++0x03 line.long 0x00 "BM1_BUF_SIZE_0,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50004++0x03 line.long 0x00 "BM1_BUF_SIZE_1,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50008++0x03 line.long 0x00 "BM1_BUF_SIZE_2,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x5000C++0x03 line.long 0x00 "BM1_BUF_SIZE_3,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50010++0x03 line.long 0x00 "BM1_BUF_SIZE_4,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50014++0x03 line.long 0x00 "BM1_BUF_SIZE_5,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50018++0x03 line.long 0x00 "BM1_BUF_SIZE_6,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x5001C++0x03 line.long 0x00 "BM1_BUF_SIZE_7,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50020++0x03 line.long 0x00 "BM1_BUF_SIZE_8,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50024++0x03 line.long 0x00 "BM1_BUF_SIZE_9,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50028++0x03 line.long 0x00 "BM1_BUF_SIZE_10,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x5002C++0x03 line.long 0x00 "BM1_BUF_SIZE_11,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50030++0x03 line.long 0x00 "BM1_BUF_SIZE_12,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50034++0x03 line.long 0x00 "BM1_BUF_SIZE_13,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50038++0x03 line.long 0x00 "BM1_BUF_SIZE_14,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x5003C++0x03 line.long 0x00 "BM1_BUF_SIZE_15,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50040++0x03 line.long 0x00 "BM1_BUF_SIZE_16,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50044++0x03 line.long 0x00 "BM1_BUF_SIZE_17,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50048++0x03 line.long 0x00 "BM1_BUF_SIZE_18,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x5004C++0x03 line.long 0x00 "BM1_BUF_SIZE_19,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50050++0x03 line.long 0x00 "BM1_BUF_SIZE_20,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50054++0x03 line.long 0x00 "BM1_BUF_SIZE_21,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50058++0x03 line.long 0x00 "BM1_BUF_SIZE_22,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x5005C++0x03 line.long 0x00 "BM1_BUF_SIZE_23,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50060++0x03 line.long 0x00 "BM1_BUF_SIZE_24,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50064++0x03 line.long 0x00 "BM1_BUF_SIZE_25,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50068++0x03 line.long 0x00 "BM1_BUF_SIZE_26,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x5006C++0x03 line.long 0x00 "BM1_BUF_SIZE_27,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50070++0x03 line.long 0x00 "BM1_BUF_SIZE_28,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50074++0x03 line.long 0x00 "BM1_BUF_SIZE_29,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x50078++0x03 line.long 0x00 "BM1_BUF_SIZE_30,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" group.long 0x5007C++0x03 line.long 0x00 "BM1_BUF_SIZE_31,Buffer Size" hexmask.long.word 0x00 10.--23. 1. " VALUE ,Buffer size in 1K-byte blocks" tree.end tree "BM2" group.long 0x150000++0x03 line.long 0x00 "BM2_BUF_SIZE_0,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150004++0x03 line.long 0x00 "BM2_BUF_SIZE_1,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150008++0x03 line.long 0x00 "BM2_BUF_SIZE_2,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x15000C++0x03 line.long 0x00 "BM2_BUF_SIZE_3,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150010++0x03 line.long 0x00 "BM2_BUF_SIZE_4,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150014++0x03 line.long 0x00 "BM2_BUF_SIZE_5,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150018++0x03 line.long 0x00 "BM2_BUF_SIZE_6,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x15001C++0x03 line.long 0x00 "BM2_BUF_SIZE_7,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150020++0x03 line.long 0x00 "BM2_BUF_SIZE_8,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150024++0x03 line.long 0x00 "BM2_BUF_SIZE_9,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150028++0x03 line.long 0x00 "BM2_BUF_SIZE_10,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x15002C++0x03 line.long 0x00 "BM2_BUF_SIZE_11,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150030++0x03 line.long 0x00 "BM2_BUF_SIZE_12,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150034++0x03 line.long 0x00 "BM2_BUF_SIZE_13,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150038++0x03 line.long 0x00 "BM2_BUF_SIZE_14,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x15003C++0x03 line.long 0x00 "BM2_BUF_SIZE_15,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150040++0x03 line.long 0x00 "BM2_BUF_SIZE_16,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150044++0x03 line.long 0x00 "BM2_BUF_SIZE_17,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150048++0x03 line.long 0x00 "BM2_BUF_SIZE_18,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x15004C++0x03 line.long 0x00 "BM2_BUF_SIZE_19,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150050++0x03 line.long 0x00 "BM2_BUF_SIZE_20,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150054++0x03 line.long 0x00 "BM2_BUF_SIZE_21,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150058++0x03 line.long 0x00 "BM2_BUF_SIZE_22,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x15005C++0x03 line.long 0x00 "BM2_BUF_SIZE_23,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150060++0x03 line.long 0x00 "BM2_BUF_SIZE_24,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150064++0x03 line.long 0x00 "BM2_BUF_SIZE_25,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150068++0x03 line.long 0x00 "BM2_BUF_SIZE_26,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x15006C++0x03 line.long 0x00 "BM2_BUF_SIZE_27,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150070++0x03 line.long 0x00 "BM2_BUF_SIZE_28,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150074++0x03 line.long 0x00 "BM2_BUF_SIZE_29,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x150078++0x03 line.long 0x00 "BM2_BUF_SIZE_30,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" group.long 0x15007C++0x03 line.long 0x00 "BM2_BUF_SIZE_31,Buffer Size" hexmask.long.word 0x00 10.--23. 1. "VALUE,Buffer size in 1K-byte blocks" tree.end tree.end width 15. tree "WR_PTR" tree "BM1" group.long 0x50080++0x03 line.long 0x00 "BM1_WR_PTR_0,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x50084++0x03 line.long 0x00 "BM1_WR_PTR_1,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x50088++0x03 line.long 0x00 "BM1_WR_PTR_2,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x5008C++0x03 line.long 0x00 "BM1_WR_PTR_3,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x50090++0x03 line.long 0x00 "BM1_WR_PTR_4,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x50094++0x03 line.long 0x00 "BM1_WR_PTR_5,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x50098++0x03 line.long 0x00 "BM1_WR_PTR_6,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x5009C++0x03 line.long 0x00 "BM1_WR_PTR_7,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500A0++0x03 line.long 0x00 "BM1_WR_PTR_8,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500A4++0x03 line.long 0x00 "BM1_WR_PTR_9,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500A8++0x03 line.long 0x00 "BM1_WR_PTR_10,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500AC++0x03 line.long 0x00 "BM1_WR_PTR_11,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500B0++0x03 line.long 0x00 "BM1_WR_PTR_12,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500B4++0x03 line.long 0x00 "BM1_WR_PTR_13,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500B8++0x03 line.long 0x00 "BM1_WR_PTR_14,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500BC++0x03 line.long 0x00 "BM1_WR_PTR_15,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500C0++0x03 line.long 0x00 "BM1_WR_PTR_16,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500C4++0x03 line.long 0x00 "BM1_WR_PTR_17,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500C8++0x03 line.long 0x00 "BM1_WR_PTR_18,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500CC++0x03 line.long 0x00 "BM1_WR_PTR_19,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500D0++0x03 line.long 0x00 "BM1_WR_PTR_20,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500D4++0x03 line.long 0x00 "BM1_WR_PTR_21,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500D8++0x03 line.long 0x00 "BM1_WR_PTR_22,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500DC++0x03 line.long 0x00 "BM1_WR_PTR_23,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500E0++0x03 line.long 0x00 "BM1_WR_PTR_24,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500E4++0x03 line.long 0x00 "BM1_WR_PTR_25,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500E8++0x03 line.long 0x00 "BM1_WR_PTR_26,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500EC++0x03 line.long 0x00 "BM1_WR_PTR_27,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500F0++0x03 line.long 0x00 "BM1_WR_PTR_28,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500F4++0x03 line.long 0x00 "BM1_WR_PTR_29,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500F8++0x03 line.long 0x00 "BM1_WR_PTR_30,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x500FC++0x03 line.long 0x00 "BM1_WR_PTR_31,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" tree.end tree "BM2" group.long 0x150080++0x03 line.long 0x00 "BM2_WR_PTR_0,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x150084++0x03 line.long 0x00 "BM2_WR_PTR_1,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x150088++0x03 line.long 0x00 "BM2_WR_PTR_2,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x15008C++0x03 line.long 0x00 "BM2_WR_PTR_3,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x150090++0x03 line.long 0x00 "BM2_WR_PTR_4,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x150094++0x03 line.long 0x00 "BM2_WR_PTR_5,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x150098++0x03 line.long 0x00 "BM2_WR_PTR_6,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x15009C++0x03 line.long 0x00 "BM2_WR_PTR_7,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500A0++0x03 line.long 0x00 "BM2_WR_PTR_8,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500A4++0x03 line.long 0x00 "BM2_WR_PTR_9,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500A8++0x03 line.long 0x00 "BM2_WR_PTR_10,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500AC++0x03 line.long 0x00 "BM2_WR_PTR_11,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500B0++0x03 line.long 0x00 "BM2_WR_PTR_12,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500B4++0x03 line.long 0x00 "BM2_WR_PTR_13,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500B8++0x03 line.long 0x00 "BM2_WR_PTR_14,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500BC++0x03 line.long 0x00 "BM2_WR_PTR_15,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500C0++0x03 line.long 0x00 "BM2_WR_PTR_16,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500C4++0x03 line.long 0x00 "BM2_WR_PTR_17,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500C8++0x03 line.long 0x00 "BM2_WR_PTR_18,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500CC++0x03 line.long 0x00 "BM2_WR_PTR_19,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500D0++0x03 line.long 0x00 "BM2_WR_PTR_20,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500D4++0x03 line.long 0x00 "BM2_WR_PTR_21,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500D8++0x03 line.long 0x00 "BM2_WR_PTR_22,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500DC++0x03 line.long 0x00 "BM2_WR_PTR_23,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500E0++0x03 line.long 0x00 "BM2_WR_PTR_24,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500E4++0x03 line.long 0x00 "BM2_WR_PTR_25,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500E8++0x03 line.long 0x00 "BM2_WR_PTR_26,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500EC++0x03 line.long 0x00 "BM2_WR_PTR_27,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500F0++0x03 line.long 0x00 "BM2_WR_PTR_28,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500F4++0x03 line.long 0x00 "BM2_WR_PTR_29,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500F8++0x03 line.long 0x00 "BM2_WR_PTR_30,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" group.long 0x1500FC++0x03 line.long 0x00 "BM2_WR_PTR_31,Write pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Write Pointer" tree.end tree.end tree "RD_PTR" tree "BM1" group.long 0x50180++0x03 line.long 0x00 "BM1_RD_PTR_0,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x50184++0x03 line.long 0x00 "BM1_RD_PTR_1,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x50188++0x03 line.long 0x00 "BM1_RD_PTR_2,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x5018C++0x03 line.long 0x00 "BM1_RD_PTR_3,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x50190++0x03 line.long 0x00 "BM1_RD_PTR_4,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x50194++0x03 line.long 0x00 "BM1_RD_PTR_5,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x50198++0x03 line.long 0x00 "BM1_RD_PTR_6,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x5019C++0x03 line.long 0x00 "BM1_RD_PTR_7,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501A0++0x03 line.long 0x00 "BM1_RD_PTR_8,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501A4++0x03 line.long 0x00 "BM1_RD_PTR_9,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501A8++0x03 line.long 0x00 "BM1_RD_PTR_10,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501AC++0x03 line.long 0x00 "BM1_RD_PTR_11,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501B0++0x03 line.long 0x00 "BM1_RD_PTR_12,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501B4++0x03 line.long 0x00 "BM1_RD_PTR_13,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501B8++0x03 line.long 0x00 "BM1_RD_PTR_14,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501BC++0x03 line.long 0x00 "BM1_RD_PTR_15,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501C0++0x03 line.long 0x00 "BM1_RD_PTR_16,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501C4++0x03 line.long 0x00 "BM1_RD_PTR_17,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501C8++0x03 line.long 0x00 "BM1_RD_PTR_18,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501CC++0x03 line.long 0x00 "BM1_RD_PTR_19,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501D0++0x03 line.long 0x00 "BM1_RD_PTR_20,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501D4++0x03 line.long 0x00 "BM1_RD_PTR_21,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501D8++0x03 line.long 0x00 "BM1_RD_PTR_22,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501DC++0x03 line.long 0x00 "BM1_RD_PTR_23,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501E0++0x03 line.long 0x00 "BM1_RD_PTR_24,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501E4++0x03 line.long 0x00 "BM1_RD_PTR_25,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501E8++0x03 line.long 0x00 "BM1_RD_PTR_26,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501EC++0x03 line.long 0x00 "BM1_RD_PTR_27,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501F0++0x03 line.long 0x00 "BM1_RD_PTR_28,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501F4++0x03 line.long 0x00 "BM1_RD_PTR_29,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501F8++0x03 line.long 0x00 "BM1_RD_PTR_30,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x501FC++0x03 line.long 0x00 "BM1_RD_PTR_31,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" tree.end tree "BM2" group.long 0x150180++0x03 line.long 0x00 "BM1_RD_PTR_0,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x150184++0x03 line.long 0x00 "BM1_RD_PTR_1,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x150188++0x03 line.long 0x00 "BM1_RD_PTR_2,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x15018C++0x03 line.long 0x00 "BM1_RD_PTR_3,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x150190++0x03 line.long 0x00 "BM1_RD_PTR_4,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x150194++0x03 line.long 0x00 "BM1_RD_PTR_5,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x150198++0x03 line.long 0x00 "BM1_RD_PTR_6,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x15019C++0x03 line.long 0x00 "BM1_RD_PTR_7,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501A0++0x03 line.long 0x00 "BM1_RD_PTR_8,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501A4++0x03 line.long 0x00 "BM1_RD_PTR_9,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501A8++0x03 line.long 0x00 "BM1_RD_PTR_10,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501AC++0x03 line.long 0x00 "BM1_RD_PTR_11,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501B0++0x03 line.long 0x00 "BM1_RD_PTR_12,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501B4++0x03 line.long 0x00 "BM1_RD_PTR_13,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501B8++0x03 line.long 0x00 "BM1_RD_PTR_14,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501BC++0x03 line.long 0x00 "BM1_RD_PTR_15,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501C0++0x03 line.long 0x00 "BM1_RD_PTR_16,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501C4++0x03 line.long 0x00 "BM1_RD_PTR_17,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501C8++0x03 line.long 0x00 "BM1_RD_PTR_18,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501CC++0x03 line.long 0x00 "BM1_RD_PTR_19,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501D0++0x03 line.long 0x00 "BM1_RD_PTR_20,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501D4++0x03 line.long 0x00 "BM1_RD_PTR_21,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501D8++0x03 line.long 0x00 "BM1_RD_PTR_22,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501DC++0x03 line.long 0x00 "BM1_RD_PTR_23,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501E0++0x03 line.long 0x00 "BM1_RD_PTR_24,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501E4++0x03 line.long 0x00 "BM1_RD_PTR_25,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501E8++0x03 line.long 0x00 "BM1_RD_PTR_26,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501EC++0x03 line.long 0x00 "BM1_RD_PTR_27,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501F0++0x03 line.long 0x00 "BM1_RD_PTR_28,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501F4++0x03 line.long 0x00 "BM1_RD_PTR_29,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501F8++0x03 line.long 0x00 "BM1_RD_PTR_30,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" group.long 0x1501FC++0x03 line.long 0x00 "BM1_RD_PTR_31,Read pointer" hexmask.long.tbyte 0x00 0.--23. 1. "VALUE,Read Pointer" tree.end tree.end width 23. textline " " group.long 0x50298++0x03 line.long 0x00 "BM1_BUFFER_WR_ENDIAN,Buffer write endian" bitfld.long 0x00 31. " VALUE31 ,Bit 31 specifies the write endian of buffer 31" "Big endian,Little endian" bitfld.long 0x00 30. " VALUE30 ,Bit 30 specifies the write endian of buffer 30" "Big endian,Little endian" bitfld.long 0x00 29. " VALUE29 ,Bit 29 specifies the write endian of buffer 29" "Big endian,Little endian" textline " " bitfld.long 0x00 28. " VALUE28 ,Bit 28 specifies the write endian of buffer 28" "Big endian,Little endian" bitfld.long 0x00 27. " VALUE27 ,Bit 27 specifies the write endian of buffer 27" "Big endian,Little endian" bitfld.long 0x00 26. " VALUE26 ,Bit 26 specifies the write endian of buffer 26" "Big endian,Little endian" textline " " bitfld.long 0x00 25. " VALUE25 ,Bit 25 specifies the write endian of buffer 25" "Big endian,Little endian" bitfld.long 0x00 24. " VALUE24 ,Bit 24 specifies the write endian of buffer 24" "Big endian,Little endian" bitfld.long 0x00 23. " VALUE23 ,Bit 23 specifies the write endian of buffer 23" "Big endian,Little endian" textline " " bitfld.long 0x00 22. " VALUE22 ,Bit 22 specifies the write endian of buffer 22" "Big endian,Little endian" bitfld.long 0x00 21. " VALUE21 ,Bit 21 specifies the write endian of buffer 21" "Big endian,Little endian" bitfld.long 0x00 20. " VALUE20 ,Bit 20 specifies the write endian of buffer 20" "Big endian,Little endian" textline " " bitfld.long 0x00 19. " VALUE19 ,Bit 19 specifies the write endian of buffer 19" "Big endian,Little endian" bitfld.long 0x00 18. " VALUE18 ,Bit 18 specifies the write endian of buffer 18" "Big endian,Little endian" bitfld.long 0x00 17. " VALUE17 ,Bit 17 specifies the write endian of buffer 17" "Big endian,Little endian" textline " " bitfld.long 0x00 16. " VALUE16 ,Bit 16 specifies the write endian of buffer 16" "Big endian,Little endian" bitfld.long 0x00 15. " VALUE15 ,Bit 15 specifies the write endian of buffer 15" "Big endian,Little endian" bitfld.long 0x00 14. " VALUE14 ,Bit 14 specifies the write endian of buffer 14" "Big endian,Little endian" textline " " bitfld.long 0x00 13. " VALUE13 ,Bit 13 specifies the write endian of buffer 13" "Big endian,Little endian" bitfld.long 0x00 12. " VALUE12 ,Bit 12 specifies the write endian of buffer 12" "Big endian,Little endian" bitfld.long 0x00 11. " VALUE11 ,Bit 11 specifies the write endian of buffer 11" "Big endian,Little endian" textline " " bitfld.long 0x00 10. " VALUE10 ,Bit 10 specifies the write endian of buffer 10" "Big endian,Little endian" bitfld.long 0x00 9. " VALUE9 ,Bit 9 specifies the write endian of buffer 9" "Big endian,Little endian" bitfld.long 0x00 8. " VALUE8 ,Bit 8 specifies the write endian of buffer 8" "Big endian,Little endian" textline " " bitfld.long 0x00 7. " VALUE7 ,Bit 7 specifies the write endian of buffer 7" "Big endian,Little endian" bitfld.long 0x00 6. " VALUE6 ,Bit 6 specifies the write endian of buffer 6" "Big endian,Little endian" bitfld.long 0x00 5. " VALUE5 ,Bit 5 specifies the write endian of buffer 5" "Big endian,Little endian" textline " " bitfld.long 0x00 4. " VALUE4 ,Bit 4 specifies the write endian of buffer 4" "Big endian,Little endian" bitfld.long 0x00 3. " VALUE3 ,Bit 3 specifies the write endian of buffer 3" "Big endian,Little endian" bitfld.long 0x00 2. " VALUE2 ,Bit 2 specifies the write endian of buffer 2" "Big endian,Little endian" textline " " bitfld.long 0x00 1. " VALUE1 ,Bit 1 specifies the write endian of buffer 1" "Big endian,Little endian" bitfld.long 0x00 0. " VALUE0 ,Bit 0 specifies the write endian of buffer 0" "Big endian,Little endian" group.long 0x150298++0x03 line.long 0x00 "BM2_BUFFER_WR_ENDIAN,Buffer write endian" bitfld.long 0x00 31. " VALUE31 ,Bit 31 specifies the write endian of buffer 31" "Big endian,Little endian" bitfld.long 0x00 30. " VALUE30 ,Bit 30 specifies the write endian of buffer 30" "Big endian,Little endian" bitfld.long 0x00 29. " VALUE29 ,Bit 29 specifies the write endian of buffer 29" "Big endian,Little endian" textline " " bitfld.long 0x00 28. " VALUE28 ,Bit 28 specifies the write endian of buffer 28" "Big endian,Little endian" bitfld.long 0x00 27. " VALUE27 ,Bit 27 specifies the write endian of buffer 27" "Big endian,Little endian" bitfld.long 0x00 26. " VALUE26 ,Bit 26 specifies the write endian of buffer 26" "Big endian,Little endian" textline " " bitfld.long 0x00 25. " VALUE25 ,Bit 25 specifies the write endian of buffer 25" "Big endian,Little endian" bitfld.long 0x00 24. " VALUE24 ,Bit 24 specifies the write endian of buffer 24" "Big endian,Little endian" bitfld.long 0x00 23. " VALUE23 ,Bit 23 specifies the write endian of buffer 23" "Big endian,Little endian" textline " " bitfld.long 0x00 22. " VALUE22 ,Bit 22 specifies the write endian of buffer 22" "Big endian,Little endian" bitfld.long 0x00 21. " VALUE21 ,Bit 21 specifies the write endian of buffer 21" "Big endian,Little endian" bitfld.long 0x00 20. " VALUE20 ,Bit 20 specifies the write endian of buffer 20" "Big endian,Little endian" textline " " bitfld.long 0x00 19. " VALUE19 ,Bit 19 specifies the write endian of buffer 19" "Big endian,Little endian" bitfld.long 0x00 18. " VALUE18 ,Bit 18 specifies the write endian of buffer 18" "Big endian,Little endian" bitfld.long 0x00 17. " VALUE17 ,Bit 17 specifies the write endian of buffer 17" "Big endian,Little endian" textline " " bitfld.long 0x00 16. " VALUE16 ,Bit 16 specifies the write endian of buffer 16" "Big endian,Little endian" bitfld.long 0x00 15. " VALUE15 ,Bit 15 specifies the write endian of buffer 15" "Big endian,Little endian" bitfld.long 0x00 14. " VALUE14 ,Bit 14 specifies the write endian of buffer 14" "Big endian,Little endian" textline " " bitfld.long 0x00 13. " VALUE13 ,Bit 13 specifies the write endian of buffer 13" "Big endian,Little endian" bitfld.long 0x00 12. " VALUE12 ,Bit 12 specifies the write endian of buffer 12" "Big endian,Little endian" bitfld.long 0x00 11. " VALUE11 ,Bit 11 specifies the write endian of buffer 11" "Big endian,Little endian" textline " " bitfld.long 0x00 10. " VALUE10 ,Bit 10 specifies the write endian of buffer 10" "Big endian,Little endian" bitfld.long 0x00 9. " VALUE9 ,Bit 9 specifies the write endian of buffer 9" "Big endian,Little endian" bitfld.long 0x00 8. " VALUE8 ,Bit 8 specifies the write endian of buffer 8" "Big endian,Little endian" textline " " bitfld.long 0x00 7. " VALUE7 ,Bit 7 specifies the write endian of buffer 7" "Big endian,Little endian" bitfld.long 0x00 6. " VALUE6 ,Bit 6 specifies the write endian of buffer 6" "Big endian,Little endian" bitfld.long 0x00 5. " VALUE5 ,Bit 5 specifies the write endian of buffer 5" "Big endian,Little endian" textline " " bitfld.long 0x00 4. " VALUE4 ,Bit 4 specifies the write endian of buffer 4" "Big endian,Little endian" bitfld.long 0x00 3. " VALUE3 ,Bit 3 specifies the write endian of buffer 3" "Big endian,Little endian" bitfld.long 0x00 2. " VALUE2 ,Bit 2 specifies the write endian of buffer 2" "Big endian,Little endian" textline " " bitfld.long 0x00 1. " VALUE1 ,Bit 1 specifies the write endian of buffer 1" "Big endian,Little endian" bitfld.long 0x00 0. " VALUE0 ,Bit 0 specifies the write endian of buffer 0" "Big endian,Little endian" tree.end width 20. tree "Access Unit Delimiter Detector" group.long 0x450634++0x03 line.long 0x00 "BM_AUD0_BUF_SELECT,Selectes buffer for AUD detector 0" bitfld.long 0x00 8. " ENABLE ,Enables AUD detection and clears the search pipe line" "Disabled,Enabled" bitfld.long 0x00 5.--6. " INDEX ,Indicates in which BM the AUD will be searched" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates in which buffer the AUD will be searched" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x450674++0x03 line.long 0x00 "BM_AUD1_BUF_SELECT,Selectes buffer for AUD detector 1" bitfld.long 0x00 8. " ENABLE ,Enables AUD detection and clears the search pipe line" "Disabled,Enabled" bitfld.long 0x00 5.--6. " INDEX ,Indicates in which BM the AUD will be searched" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates in which buffer the AUD will be searched" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" group.long 0x450600++0x03 line.long 0x00 "BM1_AUD0_VALUE,AUD write pointer of AUD detector 0" bitfld.long 0x00 16. " ENABLE ,Enables AUD detection for this Code-Mask Pair and the corresponding IRQ" "Disabled,Enabled" hexmask.long.byte 0x00 8.--15. 1. " MASK ,The Code and the Mask together determine which AUD will be detected" hexmask.long.byte 0x00 0.--7. 1. " CODE ,The Code and the Mask together determine which AUD will be detected" rgroup.long (0x450600+0x20)++0x03 line.long 0x00 "BM1_AUD0_WR_PTR,AUD write pointer of AUD detector 0" bitfld.long 0x00 25. " SEPARATEDBYPTS ,Indicates if the AUD is separated by a PTS" "Not separated,Separated" bitfld.long 0x00 24. " VALID ,Indicates if the write pointer is valid" "Invalid,Valid" hexmask.long.tbyte 0x00 0.--23. 1. " PTR ,The byte address of the first byte following AUD" group.long 0x450604++0x03 line.long 0x00 "BM1_AUD1_VALUE,AUD write pointer of AUD detector 1" bitfld.long 0x00 16. " ENABLE ,Enables AUD detection for this Code-Mask Pair and the corresponding IRQ" "Disabled,Enabled" hexmask.long.byte 0x00 8.--15. 1. " MASK ,The Code and the Mask together determine which AUD will be detected" hexmask.long.byte 0x00 0.--7. 1. " CODE ,The Code and the Mask together determine which AUD will be detected" rgroup.long (0x450604+0x20)++0x03 line.long 0x00 "BM1_AUD1_WR_PTR,AUD write pointer of AUD detector 1" bitfld.long 0x00 25. " SEPARATEDBYPTS ,Indicates if the AUD is separated by a PTS" "Not separated,Separated" bitfld.long 0x00 24. " VALID ,Indicates if the write pointer is valid" "Invalid,Valid" hexmask.long.tbyte 0x00 0.--23. 1. " PTR ,The byte address of the first byte following AUD" group.long 0x450608++0x03 line.long 0x00 "BM1_AUD2_VALUE,AUD write pointer of AUD detector 2" bitfld.long 0x00 16. " ENABLE ,Enables AUD detection for this Code-Mask Pair and the corresponding IRQ" "Disabled,Enabled" hexmask.long.byte 0x00 8.--15. 1. " MASK ,The Code and the Mask together determine which AUD will be detected" hexmask.long.byte 0x00 0.--7. 1. " CODE ,The Code and the Mask together determine which AUD will be detected" rgroup.long (0x450608+0x20)++0x03 line.long 0x00 "BM1_AUD2_WR_PTR,AUD write pointer of AUD detector 2" bitfld.long 0x00 25. " SEPARATEDBYPTS ,Indicates if the AUD is separated by a PTS" "Not separated,Separated" bitfld.long 0x00 24. " VALID ,Indicates if the write pointer is valid" "Invalid,Valid" hexmask.long.tbyte 0x00 0.--23. 1. " PTR ,The byte address of the first byte following AUD" group.long 0x45060C++0x03 line.long 0x00 "BM1_AUD3_VALUE,AUD write pointer of AUD detector 3" bitfld.long 0x00 16. " ENABLE ,Enables AUD detection for this Code-Mask Pair and the corresponding IRQ" "Disabled,Enabled" hexmask.long.byte 0x00 8.--15. 1. " MASK ,The Code and the Mask together determine which AUD will be detected" hexmask.long.byte 0x00 0.--7. 1. " CODE ,The Code and the Mask together determine which AUD will be detected" rgroup.long (0x45060C+0x20)++0x03 line.long 0x00 "BM1_AUD3_WR_PTR,AUD write pointer of AUD detector 3" bitfld.long 0x00 25. " SEPARATEDBYPTS ,Indicates if the AUD is separated by a PTS" "Not separated,Separated" bitfld.long 0x00 24. " VALID ,Indicates if the write pointer is valid" "Invalid,Valid" hexmask.long.tbyte 0x00 0.--23. 1. " PTR ,The byte address of the first byte following AUD" group.long 0x450610++0x03 line.long 0x00 "BM1_AUD4_VALUE,AUD write pointer of AUD detector 4" bitfld.long 0x00 16. " ENABLE ,Enables AUD detection for this Code-Mask Pair and the corresponding IRQ" "Disabled,Enabled" hexmask.long.byte 0x00 8.--15. 1. " MASK ,The Code and the Mask together determine which AUD will be detected" hexmask.long.byte 0x00 0.--7. 1. " CODE ,The Code and the Mask together determine which AUD will be detected" rgroup.long (0x450610+0x20)++0x03 line.long 0x00 "BM1_AUD4_WR_PTR,AUD write pointer of AUD detector 4" bitfld.long 0x00 25. " SEPARATEDBYPTS ,Indicates if the AUD is separated by a PTS" "Not separated,Separated" bitfld.long 0x00 24. " VALID ,Indicates if the write pointer is valid" "Invalid,Valid" hexmask.long.tbyte 0x00 0.--23. 1. " PTR ,The byte address of the first byte following AUD" group.long 0x450640++0x03 line.long 0x00 "BM2_AUD0_VALUE,AUD write pointer of AUD detector 0" bitfld.long 0x00 16. " ENABLE ,Enables AUD detection for this Code-Mask Pair and the corresponding IRQ" "Disabled,Enabled" hexmask.long.byte 0x00 8.--15. 1. " MASK ,The Code and the Mask together determine which AUD will be detected" hexmask.long.byte 0x00 0.--7. 1. " CODE ,The Code and the Mask together determine which AUD will be detected" rgroup.long (0x450640+0x20)++0x03 line.long 0x00 "BM2_AUD0_WR_PTR,AUD write pointer of AUD detector 0" bitfld.long 0x00 25. " SEPARATEDBYPTS ,Indicates if the AUD is separated by a PTS" "Not separated,Separated" bitfld.long 0x00 24. " VALID ,Indicates if the write pointer is valid" "Invalid,Valid" hexmask.long.tbyte 0x00 0.--23. 1. " PTR ,The byte address of the first byte following AUD" group.long 0x450644++0x03 line.long 0x00 "BM2_AUD1_VALUE,AUD write pointer of AUD detector 1" bitfld.long 0x00 16. " ENABLE ,Enables AUD detection for this Code-Mask Pair and the corresponding IRQ" "Disabled,Enabled" hexmask.long.byte 0x00 8.--15. 1. " MASK ,The Code and the Mask together determine which AUD will be detected" hexmask.long.byte 0x00 0.--7. 1. " CODE ,The Code and the Mask together determine which AUD will be detected" rgroup.long (0x450644+0x20)++0x03 line.long 0x00 "BM2_AUD1_WR_PTR,AUD write pointer of AUD detector 1" bitfld.long 0x00 25. " SEPARATEDBYPTS ,Indicates if the AUD is separated by a PTS" "Not separated,Separated" bitfld.long 0x00 24. " VALID ,Indicates if the write pointer is valid" "Invalid,Valid" hexmask.long.tbyte 0x00 0.--23. 1. " PTR ,The byte address of the first byte following AUD" group.long 0x450648++0x03 line.long 0x00 "BM2_AUD2_VALUE,AUD write pointer of AUD detector 2" bitfld.long 0x00 16. " ENABLE ,Enables AUD detection for this Code-Mask Pair and the corresponding IRQ" "Disabled,Enabled" hexmask.long.byte 0x00 8.--15. 1. " MASK ,The Code and the Mask together determine which AUD will be detected" hexmask.long.byte 0x00 0.--7. 1. " CODE ,The Code and the Mask together determine which AUD will be detected" rgroup.long (0x450648+0x20)++0x03 line.long 0x00 "BM2_AUD2_WR_PTR,AUD write pointer of AUD detector 2" bitfld.long 0x00 25. " SEPARATEDBYPTS ,Indicates if the AUD is separated by a PTS" "Not separated,Separated" bitfld.long 0x00 24. " VALID ,Indicates if the write pointer is valid" "Invalid,Valid" hexmask.long.tbyte 0x00 0.--23. 1. " PTR ,The byte address of the first byte following AUD" group.long 0x45064C++0x03 line.long 0x00 "BM2_AUD3_VALUE,AUD write pointer of AUD detector 3" bitfld.long 0x00 16. " ENABLE ,Enables AUD detection for this Code-Mask Pair and the corresponding IRQ" "Disabled,Enabled" hexmask.long.byte 0x00 8.--15. 1. " MASK ,The Code and the Mask together determine which AUD will be detected" hexmask.long.byte 0x00 0.--7. 1. " CODE ,The Code and the Mask together determine which AUD will be detected" rgroup.long (0x45064C+0x20)++0x03 line.long 0x00 "BM2_AUD3_WR_PTR,AUD write pointer of AUD detector 3" bitfld.long 0x00 25. " SEPARATEDBYPTS ,Indicates if the AUD is separated by a PTS" "Not separated,Separated" bitfld.long 0x00 24. " VALID ,Indicates if the write pointer is valid" "Invalid,Valid" hexmask.long.tbyte 0x00 0.--23. 1. " PTR ,The byte address of the first byte following AUD" group.long 0x450650++0x03 line.long 0x00 "BM2_AUD4_VALUE,AUD write pointer of AUD detector 4" bitfld.long 0x00 16. " ENABLE ,Enables AUD detection for this Code-Mask Pair and the corresponding IRQ" "Disabled,Enabled" hexmask.long.byte 0x00 8.--15. 1. " MASK ,The Code and the Mask together determine which AUD will be detected" hexmask.long.byte 0x00 0.--7. 1. " CODE ,The Code and the Mask together determine which AUD will be detected" rgroup.long (0x450650+0x20)++0x03 line.long 0x00 "BM2_AUD4_WR_PTR,AUD write pointer of AUD detector 4" bitfld.long 0x00 25. " SEPARATEDBYPTS ,Indicates if the AUD is separated by a PTS" "Not separated,Separated" bitfld.long 0x00 24. " VALID ,Indicates if the write pointer is valid" "Invalid,Valid" hexmask.long.tbyte 0x00 0.--23. 1. " PTR ,The byte address of the first byte following AUD" tree.end width 25. tree "Buffer Manager" tree "Buffer IRQ Status" rgroup.long 0x4505C0++0x03 line.long 0x00 "BM_IRQ_STATUS_RD,BM IRQ status register" bitfld.long 0x00 31. " OVERFLOW[3] ,Indicates buffer[3] overflows" "No overflow,Overflow" bitfld.long 0x00 30. " OVERFLOW[2] ,Indicates buffer[2] overflows" "No overflow,Overflow" bitfld.long 0x00 29. " OVERFLOW[1] ,Indicates buffer[1] overflows" "No overflow,Overflow" textline " " bitfld.long 0x00 28. " OVERFLOW[0] ,Indicates buffer[0] overflows" "No overflow,Overflow" bitfld.long 0x00 27. " AUDIRQ[3] ,IRQ status of AUD's" "No,Yes" bitfld.long 0x00 26. " AUDIRQ[2] ,IRQ status of AUD's" "No,Yes" textline " " bitfld.long 0x00 25. " AUDIRQ[1] ,IRQ status of AUD's" "No,Yes" bitfld.long 0x00 24. " AUDIRQ[0] ,IRQ status of AUD's" "No,Yes" bitfld.long 0x00 23. " INPUTBUFOVERFLOW ,Indicate if BM input buffer overflows" "No overflow,Overflow" textline " " bitfld.long 0x00 15. " HIGHLEVELIRQ_15 ,High level (almost full) IRQ status" "Not detected,Detected" bitfld.long 0x00 14. " HIGHLEVELIRQ_14 ,High level (almost full) IRQ status" "Not detected,Detected" bitfld.long 0x00 13. " HIGHLEVELIRQ_13 ,High level (almost full) IRQ status" "Not detected,Detected" textline " " bitfld.long 0x00 12. " HIGHLEVELIRQ_12 ,High level (almost full) IRQ status" "Not detected,Detected" bitfld.long 0x00 11. " HIGHLEVELIRQ_11 ,High level (almost full) IRQ status" "Not detected,Detected" bitfld.long 0x00 10. " HIGHLEVELIRQ_10 ,High level (almost full) IRQ status" "Not detected,Detected" textline " " bitfld.long 0x00 9. " HIGHLEVELIRQ_9 ,High level (almost full) IRQ status" "Not detected,Detected" bitfld.long 0x00 8. " HIGHLEVELIRQ_8 ,High level (almost full) IRQ status" "Not detected,Detected" bitfld.long 0x00 7. " HIGHLEVELIRQ_7 ,High level (almost full) IRQ status" "Not detected,Detected" textline " " bitfld.long 0x00 6. " HIGHLEVELIRQ_6 ,High level (almost full) IRQ status" "Not detected,Detected" bitfld.long 0x00 5. " HIGHLEVELIRQ_5 ,High level (almost full) IRQ status" "Not detected,Detected" bitfld.long 0x00 4. " HIGHLEVELIRQ_4 ,High level (almost full) IRQ status" "Not detected,Detected" textline " " bitfld.long 0x00 3. " HIGHLEVELIRQ_3 ,High level (almost full) IRQ status" "Not detected,Detected" bitfld.long 0x00 2. " HIGHLEVELIRQ_2 ,High level (almost full) IRQ status" "Not detected,Detected" bitfld.long 0x00 1. " HIGHLEVELIRQ_1 ,High level (almost full) IRQ status" "Not detected,Detected" textline " " bitfld.long 0x00 0. " HIGHLEVELIRQ_0 ,High level (almost full) IRQ status" "Not detected,Detected" hgroup.long 0x4505D0++0x03 hide.long 0x00 "BM_IRQ_STATUS_RD_CLR,MB IRQ read clear register" tree.end width 27. tree "Buffer Overflow IRQ" group.long 0x50280++0x03 line.long 0x00 "BM1_OVERFLOW_CHECK_ENABLE,Buffer overflow checking register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow shall be checked" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow shall be checked" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow shall be checked" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow shall be checked" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow shall be checked" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow shall be checked" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow shall be checked" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow shall be checked" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow shall be checked" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow shall be checked" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow shall be checked" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow shall be checked" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow shall be checked" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow shall be checked" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow shall be checked" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow shall be checked" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow shall be checked" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow shall be checked" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow shall be checked" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow shall be checked" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow shall be checked" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow shall be checked" "No,Yes" group.long 0x150280++0x03 line.long 0x00 "BM2_OVERFLOW_CHECK_ENABLE,Buffer overflow checking register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow shall be checked" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow shall be checked" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow shall be checked" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow shall be checked" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow shall be checked" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow shall be checked" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow shall be checked" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow shall be checked" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow shall be checked" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow shall be checked" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow shall be checked" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow shall be checked" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow shall be checked" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow shall be checked" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow shall be checked" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow shall be checked" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow shall be checked" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow shall be checked" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow shall be checked" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow shall be checked" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow shall be checked" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow shall be checked" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow shall be checked" "No,Yes" group.long 0x50288++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_ENABLE,Buffer overflow IRQ enable register" bitfld.long 0x00 31. " VALUE31 ,Enables buffer 31 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 30. " VALUE30 ,Enables buffer 30 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 29. " VALUE29 ,Enables buffer 29 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 28. " VALUE28 ,Enables buffer 28 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 27. " VALUE27 ,Enables buffer 27 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 26. " VALUE26 ,Enables buffer 26 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 25. " VALUE25 ,Enables buffer 25 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 24. " VALUE24 ,Enables buffer 24 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 23. " VALUE23 ,Enables buffer 23 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " VALUE22 ,Enables buffer 22 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 21. " VALUE21 ,Enables buffer 21 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 20. " VALUE20 ,Enables buffer 20 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " VALUE19 ,Enables buffer 19 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 18. " VALUE18 ,Enables buffer 18 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 17. " VALUE17 ,Enables buffer 17 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 16. " VALUE16 ,Enables buffer 16 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 15. " VALUE15 ,Enables buffer 15 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 14. " VALUE14 ,Enables buffer 14 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 13. " VALUE13 ,Enables buffer 13 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 12. " VALUE12 ,Enables buffer 12 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 11. " VALUE11 ,Enables buffer 11 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 10. " VALUE10 ,Enables buffer 10 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 9. " VALUE9 ,Enables buffer 9 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 8. " VALUE8 ,Enables buffer 8 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " VALUE7 ,Enables buffer 7 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 6. " VALUE6 ,Enables buffer 6 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 5. " VALUE5 ,Enables buffer 5 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " VALUE4 ,Enables buffer 4 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 3. " VALUE3 ,Enables buffer 3 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 2. " VALUE2 ,Enables buffer 2 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " VALUE1 ,Enables buffer 1 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 0. " VALUE0 ,Enables buffer 0 overflow IRQ" "Disabled,Enabled" group.long 0x150288++0x03 line.long 0x00 "BM2_OVERFLOW_IRQ_ENABLE,Buffer overflow IRQ enable register" bitfld.long 0x00 31. " VALUE31 ,Enables buffer 31 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 30. " VALUE30 ,Enables buffer 30 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 29. " VALUE29 ,Enables buffer 29 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 28. " VALUE28 ,Enables buffer 28 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 27. " VALUE27 ,Enables buffer 27 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 26. " VALUE26 ,Enables buffer 26 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 25. " VALUE25 ,Enables buffer 25 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 24. " VALUE24 ,Enables buffer 24 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 23. " VALUE23 ,Enables buffer 23 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " VALUE22 ,Enables buffer 22 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 21. " VALUE21 ,Enables buffer 21 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 20. " VALUE20 ,Enables buffer 20 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " VALUE19 ,Enables buffer 19 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 18. " VALUE18 ,Enables buffer 18 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 17. " VALUE17 ,Enables buffer 17 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 16. " VALUE16 ,Enables buffer 16 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 15. " VALUE15 ,Enables buffer 15 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 14. " VALUE14 ,Enables buffer 14 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 13. " VALUE13 ,Enables buffer 13 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 12. " VALUE12 ,Enables buffer 12 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 11. " VALUE11 ,Enables buffer 11 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 10. " VALUE10 ,Enables buffer 10 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 9. " VALUE9 ,Enables buffer 9 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 8. " VALUE8 ,Enables buffer 8 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " VALUE7 ,Enables buffer 7 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 6. " VALUE6 ,Enables buffer 6 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 5. " VALUE5 ,Enables buffer 5 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " VALUE4 ,Enables buffer 4 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 3. " VALUE3 ,Enables buffer 3 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 2. " VALUE2 ,Enables buffer 2 overflow IRQ" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " VALUE1 ,Enables buffer 1 overflow IRQ" "Disabled,Enabled" bitfld.long 0x00 0. " VALUE0 ,Enables buffer 0 overflow IRQ" "Disabled,Enabled" rgroup.long 0x50290++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_RD,Buffer overflow IRQ status" bitfld.long 0x00 31. " VALUE31 ,Indicates if buffer 31 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 30. " VALUE30 ,Indicates if buffer 30 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 29. " VALUE29 ,Indicates if buffer 29 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 28. " VALUE28 ,Indicates if buffer 28 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 27. " VALUE27 ,Indicates if buffer 27 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 26. " VALUE26 ,Indicates if buffer 26 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 25. " VALUE25 ,Indicates if buffer 25 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 24. " VALUE24 ,Indicates if buffer 24 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 23. " VALUE23 ,Indicates if buffer 23 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 22. " VALUE22 ,Indicates if buffer 22 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 21. " VALUE21 ,Indicates if buffer 21 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 20. " VALUE20 ,Indicates if buffer 20 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 19. " VALUE19 ,Indicates if buffer 19 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 18. " VALUE18 ,Indicates if buffer 18 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 17. " VALUE17 ,Indicates if buffer 17 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 16. " VALUE16 ,Indicates if buffer 16 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 15. " VALUE15 ,Indicates if buffer 15 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 14. " VALUE14 ,Indicates if buffer 14 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 13. " VALUE13 ,Indicates if buffer 13 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 12. " VALUE12 ,Indicates if buffer 12 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 11. " VALUE11 ,Indicates if buffer 11 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 10. " VALUE10 ,Indicates if buffer 10 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 9. " VALUE9 ,Indicates if buffer 9 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 8. " VALUE8 ,Indicates if buffer 8 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 7. " VALUE7 ,Indicates if buffer 7 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 6. " VALUE6 ,Indicates if buffer 6 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 5. " VALUE5 ,Indicates if buffer 5 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 4. " VALUE4 ,Indicates if buffer 4 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 3. " VALUE3 ,Indicates if buffer 3 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 2. " VALUE2 ,Indicates if buffer 2 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 1. " VALUE1 ,Indicates if buffer 1 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 0. " VALUE0 ,Indicates if buffer 0 overflow IRQ is generated" "No overflow,Overflow" rgroup.long 0x150290++0x03 line.long 0x00 "BM2_OVERFLOW_IRQ_RD,Buffer overflow IRQ status" bitfld.long 0x00 31. " VALUE31 ,Indicates if buffer 31 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 30. " VALUE30 ,Indicates if buffer 30 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 29. " VALUE29 ,Indicates if buffer 29 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 28. " VALUE28 ,Indicates if buffer 28 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 27. " VALUE27 ,Indicates if buffer 27 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 26. " VALUE26 ,Indicates if buffer 26 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 25. " VALUE25 ,Indicates if buffer 25 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 24. " VALUE24 ,Indicates if buffer 24 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 23. " VALUE23 ,Indicates if buffer 23 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 22. " VALUE22 ,Indicates if buffer 22 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 21. " VALUE21 ,Indicates if buffer 21 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 20. " VALUE20 ,Indicates if buffer 20 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 19. " VALUE19 ,Indicates if buffer 19 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 18. " VALUE18 ,Indicates if buffer 18 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 17. " VALUE17 ,Indicates if buffer 17 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 16. " VALUE16 ,Indicates if buffer 16 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 15. " VALUE15 ,Indicates if buffer 15 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 14. " VALUE14 ,Indicates if buffer 14 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 13. " VALUE13 ,Indicates if buffer 13 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 12. " VALUE12 ,Indicates if buffer 12 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 11. " VALUE11 ,Indicates if buffer 11 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 10. " VALUE10 ,Indicates if buffer 10 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 9. " VALUE9 ,Indicates if buffer 9 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 8. " VALUE8 ,Indicates if buffer 8 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 7. " VALUE7 ,Indicates if buffer 7 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 6. " VALUE6 ,Indicates if buffer 6 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 5. " VALUE5 ,Indicates if buffer 5 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 4. " VALUE4 ,Indicates if buffer 4 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 3. " VALUE3 ,Indicates if buffer 3 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 2. " VALUE2 ,Indicates if buffer 2 overflow IRQ is generated" "No overflow,Overflow" textline " " bitfld.long 0x00 1. " VALUE1 ,Indicates if buffer 1 overflow IRQ is generated" "No overflow,Overflow" bitfld.long 0x00 0. " VALUE0 ,Indicates if buffer 0 overflow IRQ is generated" "No overflow,Overflow" rgroup.long 0x50284++0x03 line.long 0x00 "BM1_OVERFLOW_STATUS,Buffer overflow status" bitfld.long 0x00 31. " VALUE31 ,Bit 31 corresponds to buffer 31" "Not overflow,Overflow" bitfld.long 0x00 30. " VALUE30 ,Bit 30 corresponds to buffer 30" "Not overflow,Overflow" bitfld.long 0x00 29. " VALUE29 ,Bit 29 corresponds to buffer 29" "Not overflow,Overflow" textline " " bitfld.long 0x00 28. " VALUE28 ,Bit 28 corresponds to buffer 28" "Not overflow,Overflow" bitfld.long 0x00 27. " VALUE27 ,Bit 27 corresponds to buffer 27" "Not overflow,Overflow" bitfld.long 0x00 26. " VALUE26 ,Bit 26 corresponds to buffer 26" "Not overflow,Overflow" textline " " bitfld.long 0x00 25. " VALUE25 ,Bit 25 corresponds to buffer 25" "Not overflow,Overflow" bitfld.long 0x00 24. " VALUE24 ,Bit 24 corresponds to buffer 24" "Not overflow,Overflow" bitfld.long 0x00 23. " VALUE23 ,Bit 23 corresponds to buffer 23" "Not overflow,Overflow" textline " " bitfld.long 0x00 22. " VALUE22 ,Bit 22 corresponds to buffer 22" "Not overflow,Overflow" bitfld.long 0x00 21. " VALUE21 ,Bit 21 corresponds to buffer 21" "Not overflow,Overflow" bitfld.long 0x00 20. " VALUE20 ,Bit 20 corresponds to buffer 20" "Not overflow,Overflow" textline " " bitfld.long 0x00 19. " VALUE19 ,Bit 19 corresponds to buffer 19" "Not overflow,Overflow" bitfld.long 0x00 18. " VALUE18 ,Bit 18 corresponds to buffer 18" "Not overflow,Overflow" bitfld.long 0x00 17. " VALUE17 ,Bit 17 corresponds to buffer 17" "Not overflow,Overflow" textline " " bitfld.long 0x00 16. " VALUE16 ,Bit 16 corresponds to buffer 16" "Not overflow,Overflow" bitfld.long 0x00 15. " VALUE15 ,Bit 15 corresponds to buffer 15" "Not overflow,Overflow" bitfld.long 0x00 14. " VALUE14 ,Bit 14 corresponds to buffer 14" "Not overflow,Overflow" textline " " bitfld.long 0x00 13. " VALUE13 ,Bit 13 corresponds to buffer 13" "Not overflow,Overflow" bitfld.long 0x00 12. " VALUE12 ,Bit 12 corresponds to buffer 12" "Not overflow,Overflow" bitfld.long 0x00 11. " VALUE11 ,Bit 11 corresponds to buffer 11" "Not overflow,Overflow" textline " " bitfld.long 0x00 10. " VALUE10 ,Bit 10 corresponds to buffer 10" "Not overflow,Overflow" bitfld.long 0x00 9. " VALUE9 ,Bit 9 corresponds to buffer 9" "Not overflow,Overflow" bitfld.long 0x00 8. " VALUE8 ,Bit 8 corresponds to buffer 8" "Not overflow,Overflow" textline " " bitfld.long 0x00 7. " VALUE7 ,Bit 7 corresponds to buffer 7" "Not overflow,Overflow" bitfld.long 0x00 6. " VALUE6 ,Bit 6 corresponds to buffer 6" "Not overflow,Overflow" bitfld.long 0x00 5. " VALUE5 ,Bit 5 corresponds to buffer 5" "Not overflow,Overflow" textline " " bitfld.long 0x00 4. " VALUE4 ,Bit 4 corresponds to buffer 4" "Not overflow,Overflow" bitfld.long 0x00 3. " VALUE3 ,Bit 3 corresponds to buffer 3" "Not overflow,Overflow" bitfld.long 0x00 2. " VALUE2 ,Bit 2 corresponds to buffer 2" "Not overflow,Overflow" textline " " bitfld.long 0x00 1. " VALUE1 ,Bit 1 corresponds to buffer 1" "Not overflow,Overflow" bitfld.long 0x00 0. " VALUE0 ,Bit 0 corresponds to buffer 0" "Not overflow,Overflow" rgroup.long 0x150284++0x03 line.long 0x00 "BM2_OVERFLOW_STATUS,Buffer overflow status" bitfld.long 0x00 31. " VALUE31 ,Bit 31 corresponds to buffer 31" "Not overflow,Overflow" bitfld.long 0x00 30. " VALUE30 ,Bit 30 corresponds to buffer 30" "Not overflow,Overflow" bitfld.long 0x00 29. " VALUE29 ,Bit 29 corresponds to buffer 29" "Not overflow,Overflow" textline " " bitfld.long 0x00 28. " VALUE28 ,Bit 28 corresponds to buffer 28" "Not overflow,Overflow" bitfld.long 0x00 27. " VALUE27 ,Bit 27 corresponds to buffer 27" "Not overflow,Overflow" bitfld.long 0x00 26. " VALUE26 ,Bit 26 corresponds to buffer 26" "Not overflow,Overflow" textline " " bitfld.long 0x00 25. " VALUE25 ,Bit 25 corresponds to buffer 25" "Not overflow,Overflow" bitfld.long 0x00 24. " VALUE24 ,Bit 24 corresponds to buffer 24" "Not overflow,Overflow" bitfld.long 0x00 23. " VALUE23 ,Bit 23 corresponds to buffer 23" "Not overflow,Overflow" textline " " bitfld.long 0x00 22. " VALUE22 ,Bit 22 corresponds to buffer 22" "Not overflow,Overflow" bitfld.long 0x00 21. " VALUE21 ,Bit 21 corresponds to buffer 21" "Not overflow,Overflow" bitfld.long 0x00 20. " VALUE20 ,Bit 20 corresponds to buffer 20" "Not overflow,Overflow" textline " " bitfld.long 0x00 19. " VALUE19 ,Bit 19 corresponds to buffer 19" "Not overflow,Overflow" bitfld.long 0x00 18. " VALUE18 ,Bit 18 corresponds to buffer 18" "Not overflow,Overflow" bitfld.long 0x00 17. " VALUE17 ,Bit 17 corresponds to buffer 17" "Not overflow,Overflow" textline " " bitfld.long 0x00 16. " VALUE16 ,Bit 16 corresponds to buffer 16" "Not overflow,Overflow" bitfld.long 0x00 15. " VALUE15 ,Bit 15 corresponds to buffer 15" "Not overflow,Overflow" bitfld.long 0x00 14. " VALUE14 ,Bit 14 corresponds to buffer 14" "Not overflow,Overflow" textline " " bitfld.long 0x00 13. " VALUE13 ,Bit 13 corresponds to buffer 13" "Not overflow,Overflow" bitfld.long 0x00 12. " VALUE12 ,Bit 12 corresponds to buffer 12" "Not overflow,Overflow" bitfld.long 0x00 11. " VALUE11 ,Bit 11 corresponds to buffer 11" "Not overflow,Overflow" textline " " bitfld.long 0x00 10. " VALUE10 ,Bit 10 corresponds to buffer 10" "Not overflow,Overflow" bitfld.long 0x00 9. " VALUE9 ,Bit 9 corresponds to buffer 9" "Not overflow,Overflow" bitfld.long 0x00 8. " VALUE8 ,Bit 8 corresponds to buffer 8" "Not overflow,Overflow" textline " " bitfld.long 0x00 7. " VALUE7 ,Bit 7 corresponds to buffer 7" "Not overflow,Overflow" bitfld.long 0x00 6. " VALUE6 ,Bit 6 corresponds to buffer 6" "Not overflow,Overflow" bitfld.long 0x00 5. " VALUE5 ,Bit 5 corresponds to buffer 5" "Not overflow,Overflow" textline " " bitfld.long 0x00 4. " VALUE4 ,Bit 4 corresponds to buffer 4" "Not overflow,Overflow" bitfld.long 0x00 3. " VALUE3 ,Bit 3 corresponds to buffer 3" "Not overflow,Overflow" bitfld.long 0x00 2. " VALUE2 ,Bit 2 corresponds to buffer 2" "Not overflow,Overflow" textline " " bitfld.long 0x00 1. " VALUE1 ,Bit 1 corresponds to buffer 1" "Not overflow,Overflow" bitfld.long 0x00 0. " VALUE0 ,Bit 0 corresponds to buffer 0" "Not overflow,Overflow" hgroup.long 0x50290++0x03 hide.long 0x00 "BM1_OVERFLOW_IRQ_RD_CLR,Buffer overflow IRQ read clear register" hgroup.long 0x150290++0x03 hide.long 0x00 "BM2_OVERFLOW_IRQ_RD_CLR,Buffer overflow IRQ read clear register" wgroup.long 0x50294++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_WR_CLR,Buffer overflow IRQ write clear register" bitfld.long 0x00 31. " VALUE31 ,Indicates if buffer 31 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 30. " VALUE30 ,Indicates if buffer 30 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 29. " VALUE29 ,Indicates if buffer 29 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 28. " VALUE28 ,Indicates if buffer 28 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 27. " VALUE27 ,Indicates if buffer 27 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 26. " VALUE26 ,Indicates if buffer 26 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 25. " VALUE25 ,Indicates if buffer 25 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 24. " VALUE24 ,Indicates if buffer 24 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 23. " VALUE23 ,Indicates if buffer 23 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 22. " VALUE22 ,Indicates if buffer 22 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 21. " VALUE21 ,Indicates if buffer 21 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 20. " VALUE20 ,Indicates if buffer 20 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 19. " VALUE19 ,Indicates if buffer 19 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 18. " VALUE18 ,Indicates if buffer 18 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 17. " VALUE17 ,Indicates if buffer 17 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 16. " VALUE16 ,Indicates if buffer 16 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 15. " VALUE15 ,Indicates if buffer 15 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 14. " VALUE14 ,Indicates if buffer 14 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 13. " VALUE13 ,Indicates if buffer 13 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 12. " VALUE12 ,Indicates if buffer 12 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 11. " VALUE11 ,Indicates if buffer 11 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 10. " VALUE10 ,Indicates if buffer 10 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 9. " VALUE9 ,Indicates if buffer 9 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 8. " VALUE8 ,Indicates if buffer 8 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 7. " VALUE7 ,Indicates if buffer 7 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 6. " VALUE6 ,Indicates if buffer 6 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 5. " VALUE5 ,Indicates if buffer 5 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 4. " VALUE4 ,Indicates if buffer 4 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 3. " VALUE3 ,Indicates if buffer 3 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 2. " VALUE2 ,Indicates if buffer 2 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 1. " VALUE1 ,Indicates if buffer 1 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 0. " VALUE0 ,Indicates if buffer 0 overflow IRQ is generated" "Clear,Not Clear" wgroup.long 0x150294++0x03 line.long 0x00 "BM2_OVERFLOW_IRQ_WR_CLR,Buffer overflow IRQ write clear register" bitfld.long 0x00 31. " VALUE31 ,Indicates if buffer 31 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 30. " VALUE30 ,Indicates if buffer 30 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 29. " VALUE29 ,Indicates if buffer 29 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 28. " VALUE28 ,Indicates if buffer 28 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 27. " VALUE27 ,Indicates if buffer 27 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 26. " VALUE26 ,Indicates if buffer 26 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 25. " VALUE25 ,Indicates if buffer 25 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 24. " VALUE24 ,Indicates if buffer 24 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 23. " VALUE23 ,Indicates if buffer 23 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 22. " VALUE22 ,Indicates if buffer 22 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 21. " VALUE21 ,Indicates if buffer 21 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 20. " VALUE20 ,Indicates if buffer 20 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 19. " VALUE19 ,Indicates if buffer 19 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 18. " VALUE18 ,Indicates if buffer 18 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 17. " VALUE17 ,Indicates if buffer 17 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 16. " VALUE16 ,Indicates if buffer 16 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 15. " VALUE15 ,Indicates if buffer 15 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 14. " VALUE14 ,Indicates if buffer 14 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 13. " VALUE13 ,Indicates if buffer 13 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 12. " VALUE12 ,Indicates if buffer 12 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 11. " VALUE11 ,Indicates if buffer 11 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 10. " VALUE10 ,Indicates if buffer 10 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 9. " VALUE9 ,Indicates if buffer 9 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 8. " VALUE8 ,Indicates if buffer 8 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 7. " VALUE7 ,Indicates if buffer 7 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 6. " VALUE6 ,Indicates if buffer 6 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 5. " VALUE5 ,Indicates if buffer 5 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 4. " VALUE4 ,Indicates if buffer 4 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 3. " VALUE3 ,Indicates if buffer 3 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 2. " VALUE2 ,Indicates if buffer 2 overflow IRQ is generated" "Clear,Not Clear" textline " " bitfld.long 0x00 1. " VALUE1 ,Indicates if buffer 1 overflow IRQ is generated" "Clear,Not Clear" bitfld.long 0x00 0. " VALUE0 ,Indicates if buffer 0 overflow IRQ is generated" "Clear,Not Clear" width 35. tree "BM_OVERFLOW_IRQ_SINGLE_RD_CLR" tree "BM1" rgroup.long 0x50200++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_1,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50204++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_2,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50208++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_3,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x5020C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_4,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50210++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_5,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50214++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_6,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50218++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_7,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x5021C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_8,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50220++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_9,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50224++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_10,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50228++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_11,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x5022C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_12,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50230++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_13,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50234++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_14,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50238++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_15,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x5023C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_16,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50240++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_17,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50244++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_18,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50248++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_19,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x5024C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_20,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50250++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_21,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50254++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_22,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50258++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_23,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x5025C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_24,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50260++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_25,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50264++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_26,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50268++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_27,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x5026C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_28,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50270++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_29,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50274++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_30,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x50278++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_31,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x5027C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_32,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" tree.end tree "BM2" rgroup.long 0x150200++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_1,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150204++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_2,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150208++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_3,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x15020C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_4,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150210++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_5,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150214++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_6,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150218++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_7,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x15021C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_8,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150220++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_9,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150224++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_10,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150228++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_11,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x15022C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_12,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150230++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_13,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150234++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_14,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150238++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_15,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x15023C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_16,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150240++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_17,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150244++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_18,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150248++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_19,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x15024C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_20,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150250++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_21,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150254++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_22,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150258++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_23,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x15025C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_24,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150260++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_25,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150264++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_26,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150268++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_27,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x15026C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_28,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150270++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_29,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150274++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_30,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x150278++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_31,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" rgroup.long 0x15027C++0x03 line.long 0x00 "BM1_OVERFLOW_IRQ_SINGLE_RD_CLR_32,Buffer overflow IRQ individual clear register" bitfld.long 0x00 31. " VALUE_31 ,Bit 31 indicates if buffer 31 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 30. " VALUE_30 ,Bit 30 indicates if buffer 30 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 29. " VALUE_29 ,Bit 29 indicates if buffer 29 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 28. " VALUE_28 ,Bit 28 indicates if buffer 28 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 27. " VALUE_27 ,Bit 27 indicates if buffer 27 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 26. " VALUE_26 ,Bit 26 indicates if buffer 26 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 25. " VALUE_25 ,Bit 25 indicates if buffer 25 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 24. " VALUE_24 ,Bit 24 indicates if buffer 24 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 23. " VALUE_23 ,Bit 23 indicates if buffer 23 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 22. " VALUE_22 ,Bit 22 indicates if buffer 22 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 21. " VALUE_21 ,Bit 21 indicates if buffer 21 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 20. " VALUE_20 ,Bit 20 indicates if buffer 20 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 19. " VALUE_19 ,Bit 19 indicates if buffer 19 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 18. " VALUE_18 ,Bit 18 indicates if buffer 18 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 17. " VALUE_17 ,Bit 17 indicates if buffer 17 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 16. " VALUE_16 ,Bit 16 indicates if buffer 16 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 15. " VALUE_15 ,Bit 15 indicates if buffer 15 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 14. " VALUE_14 ,Bit 14 indicates if buffer 14 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 13. " VALUE_13 ,Bit 13 indicates if buffer 13 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 12. " VALUE_12 ,Bit 12 indicates if buffer 12 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 11. " VALUE_11 ,Bit 11 indicates if buffer 11 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 10. " VALUE_10 ,Bit 10 indicates if buffer 10 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 9. " VALUE_9 ,Bit 9 indicates if buffer 9 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 8. " VALUE_8 ,Bit 8 indicates if buffer 8 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 7. " VALUE_7 ,Bit 7 indicates if buffer 7 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 6. " VALUE_6 ,Bit 6 indicates if buffer 6 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 5. " VALUE_5 ,Bit 5 indicates if buffer 5 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 4. " VALUE_4 ,Bit 4 indicates if buffer 4 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 3. " VALUE_3 ,Bit 3 indicates if buffer 3 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 2. " VALUE_2 ,Bit 2 indicates if buffer 2 overflow IRQ is generated" "No,Yes" textline " " bitfld.long 0x00 1. " VALUE_1 ,Bit 1 indicates if buffer 1 overflow IRQ is generated" "No,Yes" bitfld.long 0x00 0. " VALUE_0 ,Bit 0 indicates if buffer 0 overflow IRQ is generated" "No,Yes" tree.end tree.end tree.end width 20. tree "AUD IRQ" rgroup.long 0x450638++0x03 line.long 0x00 "BM_AUD0_IRQ_RD,AUD IRQ status register of AUD detector 0" bitfld.long 0x00 4. " VALUE_4 ,Indicates if the 4 AUD Code-Mask Pair defined" "Not found,Found" bitfld.long 0x00 3. " VALUE_3 ,Indicates if the 3 AUD Code-Mask Pair defined" "Not found,Found" textline " " bitfld.long 0x00 2. " VALUE_2 ,Indicates if the 2 AUD Code-Mask Pair defined" "Not found,Found" bitfld.long 0x00 1. " VALUE_1 ,Indicates if the 1 AUD Code-Mask Pair defined" "Not found,Found" bitfld.long 0x00 0. " VALUE_0 ,Indicates if the 0 AUD Code-Mask Pair defined" "Not found,Found" wgroup.long (0x450638+0x04)++0x03 line.long 0x00 "BM_AUD0_IRQ_WR_CLR,AUD IRQ write clear register for AUD detector 0" bitfld.long 0x00 4. " VALUE_4 ,Writing 0 to bit 4 clears AUD IRQ for AUD value 4" "Not found,Found" bitfld.long 0x00 3. " VALUE_3 ,Writing 0 to bit 3 clears AUD IRQ for AUD value 3" "Not found,Found" textline " " bitfld.long 0x00 2. " VALUE_2 ,Writing 0 to bit 2 clears AUD IRQ for AUD value 2" "Not found,Found" bitfld.long 0x00 1. " VALUE_1 ,Writing 0 to bit 1 clears AUD IRQ for AUD value 1" "Not found,Found" bitfld.long 0x00 0. " VALUE_0 ,Writing 0 to bit 0 clears AUD IRQ for AUD value 0" "Not found,Found" rgroup.long 0x450678++0x03 line.long 0x00 "BM_AUD1_IRQ_RD,AUD IRQ status register of AUD detector 1" bitfld.long 0x00 4. " VALUE_4 ,Indicates if the 4 AUD Code-Mask Pair defined" "Not found,Found" bitfld.long 0x00 3. " VALUE_3 ,Indicates if the 3 AUD Code-Mask Pair defined" "Not found,Found" textline " " bitfld.long 0x00 2. " VALUE_2 ,Indicates if the 2 AUD Code-Mask Pair defined" "Not found,Found" bitfld.long 0x00 1. " VALUE_1 ,Indicates if the 1 AUD Code-Mask Pair defined" "Not found,Found" bitfld.long 0x00 0. " VALUE_0 ,Indicates if the 0 AUD Code-Mask Pair defined" "Not found,Found" wgroup.long (0x450678+0x04)++0x03 line.long 0x00 "BM_AUD1_IRQ_WR_CLR,AUD IRQ write clear register for AUD detector 1" bitfld.long 0x00 4. " VALUE_4 ,Writing 0 to bit 4 clears AUD IRQ for AUD value 4" "Not found,Found" bitfld.long 0x00 3. " VALUE_3 ,Writing 0 to bit 3 clears AUD IRQ for AUD value 3" "Not found,Found" textline " " bitfld.long 0x00 2. " VALUE_2 ,Writing 0 to bit 2 clears AUD IRQ for AUD value 2" "Not found,Found" bitfld.long 0x00 1. " VALUE_1 ,Writing 0 to bit 1 clears AUD IRQ for AUD value 1" "Not found,Found" bitfld.long 0x00 0. " VALUE_0 ,Writing 0 to bit 0 clears AUD IRQ for AUD value 0" "Not found,Found" rgroup.long 0x450740++0x03 line.long 0x00 "BM_IN_BUF_AUD_IRQ_RD,Debug register" tree.end width 31. tree "Input Buffer Overflow IRQ" group.long 0x4505E0++0x03 line.long 0x00 "BM_IN_BUF_AFAE_THRESHOLD,Input buffer almost full and almost empty threshold register" hexmask.long.byte 0x00 8.--15. 1. " ALMOSTFULL ,Threshold for BM input buffer almost full signal" hexmask.long.byte 0x00 0.--7. 1. " ALMOSTEMPTY ,Threshold for BM input buffer almost empty signal" group.long 0x4505D4++0x03 line.long 0x00 "BM_IN_BUF_OVERFLOW_IRQ_ENABLE,Input buffer overflow IRQ enable register" bitfld.long 0x00 0. " VALUE ,Enables BM input buffer overflow IRQ" "Disabled,Enabled" rgroup.long 0x4505D8++0x03 line.long 0x00 "BM_IN_BUF_OVERFLOW_IRQ_RD,Input buffer overflow IRQ status register" bitfld.long 0x00 12. " VALID ,Indicates if the IRQ is valid" "Invalid,Valid" bitfld.long 0x00 8.--9. " INDEX ,Indicates which BM receives data from TSD as the input buffer overflows" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates for which buffer the input buffer collects data as it overflows" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hgroup.long 0x4505DC++0x03 hide.long 0x00 "BM_IN_BUF_OVERFLOW_IRQ_RD_CLR,Input buffer overflow IRQ read clear register" tree.end textline " " group.long 0x450400++0x03 line.long 0x00 "BM_HCB_ENABLE_SINGLE,HCB enable register" group.long 0x450420++0x07 line.long 0x00 "BM_HCB_ENABLE_ALL,HCB enable register" line.long 0x04 "BM_HCB_RD_ENDIAN,HCB read endian" group.long 0x4504C0++0x03 line.long 0x00 "BM_LOW_LEV_CFG_0,Low level IRQ configuration register" group.long 0x4504C4++0x03 line.long 0x00 "BM_LOW_LEV_CFG_1,Low level IRQ configuration register" group.long 0x4504C8++0x03 line.long 0x00 "BM_LOW_LEV_CFG_2,Low level IRQ configuration register" group.long 0x4504CC++0x03 line.long 0x00 "BM_LOW_LEV_CFG_3,Low level IRQ configuration register" group.long 0x4504D0++0x03 line.long 0x00 "BM_LOW_LEV_CFG_4,Low level IRQ configuration register" group.long 0x4504D4++0x03 line.long 0x00 "BM_LOW_LEV_CFG_5,Low level IRQ configuration register" group.long 0x4504D8++0x03 line.long 0x00 "BM_LOW_LEV_CFG_6,Low level IRQ configuration register" width 27. tree "Buffer High Level IRQ" group.long 0x450540++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_0,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x450540+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_0,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x450544++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_1,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x450544+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_1,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x450548++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_2,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x450548+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_2,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x45054C++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_3,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x45054C+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_3,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x450550++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_4,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x450550+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_4,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x450554++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_5,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x450554+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_5,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x450558++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_6,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x450558+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_6,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x45055C++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_7,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x45055C+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_7,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x450560++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_8,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x450560+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_8,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x450564++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_9,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x450564+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_9,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x450568++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_10,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x450568+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_10,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x45056C++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_11,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x45056C+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_11,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x450570++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_12,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x450570+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_12,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x450574++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_13,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x450574+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_13,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x450578++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_14,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x450578+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_14,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" group.long 0x45057C++0x03 line.long 0x00 "BM_HIGH_LEV_CFG_15,Low level IRQ configuration register" bitfld.long 0x00 31. " IRQEN ,High level IRQ enable bit" "Disabled,Enabled" hexmask.long.word 0x00 8.--23. 1. " THRESHOLD ,Buffer high level threshold" textline " " bitfld.long 0x00 5.--6. " INDEX ,Indicates which BM the high level shall be detected" "0,1,2,3" bitfld.long 0x00 0.--4. " BUFFERINDEX ,Indicates which buffer the high level shall be detected" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" rgroup.long (0x45057C+0x40)++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_RD_CLR_15,High level IRQ real clear register" hexmask.long.word 0x00 0.--15. 1. " VALUE ,A read access of this register will clear the high level IRQ n (IRQ 0 to 15)" wgroup.long 0x4505E4++0x03 line.long 0x00 "BM_HIGH_LEV_IRQ_WR_CLR,High level IRQ write clear register" bitfld.long 0x00 15. " VALUE15 ,Writing 1 to bit 15 will clear the high level IRQ in the corresponding buffer 15" "Clear,Not clear" bitfld.long 0x00 14. " VALUE14 ,Writing 1 to bit 14 will clear the high level IRQ in the corresponding buffer 14" "Clear,Not clear" bitfld.long 0x00 13. " VALUE13 ,Writing 1 to bit 13 will clear the high level IRQ in the corresponding buffer 13" "Clear,Not clear" textline " " bitfld.long 0x00 12. " VALUE12 ,Writing 1 to bit 12 will clear the high level IRQ in the corresponding buffer 12" "Clear,Not clear" bitfld.long 0x00 11. " VALUE11 ,Writing 1 to bit 11 will clear the high level IRQ in the corresponding buffer 11" "Clear,Not clear" bitfld.long 0x00 10. " VALUE10 ,Writing 1 to bit 10 will clear the high level IRQ in the corresponding buffer 10" "Clear,Not clear" textline " " bitfld.long 0x00 9. " VALUE9 ,Writing 1 to bit 9 will clear the high level IRQ in the corresponding buffer 9" "Clear,Not clear" bitfld.long 0x00 8. " VALUE8 ,Writing 1 to bit 8 will clear the high level IRQ in the corresponding buffer 8" "Clear,Not clear" bitfld.long 0x00 7. " VALUE7 ,Writing 1 to bit 7 will clear the high level IRQ in the corresponding buffer 7" "Clear,Not clear" textline " " bitfld.long 0x00 6. " VALUE6 ,Writing 1 to bit 6 will clear the high level IRQ in the corresponding buffer 6" "Clear,Not clear" bitfld.long 0x00 5. " VALUE5 ,Writing 1 to bit 5 will clear the high level IRQ in the corresponding buffer 5" "Clear,Not clear" bitfld.long 0x00 4. " VALUE4 ,Writing 1 to bit 4 will clear the high level IRQ in the corresponding buffer 4" "Clear,Not clear" textline " " bitfld.long 0x00 3. " VALUE3 ,Writing 1 to bit 3 will clear the high level IRQ in the corresponding buffer 3" "Clear,Not clear" bitfld.long 0x00 2. " VALUE2 ,Writing 1 to bit 2 will clear the high level IRQ in the corresponding buffer 2" "Clear,Not clear" bitfld.long 0x00 1. " VALUE1 ,Writing 1 to bit 1 will clear the high level IRQ in the corresponding buffer 1" "Clear,Not clear" textline " " bitfld.long 0x00 0. " VALUE0 ,Writing 1 to bit 0 will clear the high level IRQ in the corresponding buffer 0" "Clear,Not clear" hgroup.long 0x4505C4++0x03 hide.long 0x00 "BM_LEVEL_IRQ_RD_CLR,MB High and low level IRQ read clear register" tree.end width 15. tree "BM FSM" group.long 0x4505CC++0x03 line.long 0x00 "BM_FSM_ENABLE,Debug register" bitfld.long 0x00 2. " INBUFENABLE ,Enables BM input buffer" "Disabled,Enabled" bitfld.long 0x00 1. " WRAXIENABLE ,Enables AXI write access" "Disabled,Enabled" bitfld.long 0x00 0. " RDAXIENABLE ,Enables AXI read access" "Disabled,Enabled" if ((((per.l(ad:0xC0000000+0x4505C8))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x4505C8))&0x80)==0x80)) rgroup.long 0x4505C8++0x03 line.long 0x00 "BM_STATUS,Debug register" bitfld.long 0x00 31. " AXIACTIVE ,Indicates if AXI bus access is active" "Not active,Avtive" bitfld.long 0x00 27.--28. " HCBRD ,Buffer manager HCB read state" "0,1,2,3" bitfld.long 0x00 24.--26. " AXIRD ,Buffer manager AXI bus read state" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 20.--23. " BMINBUFRD ,Buffer manager input buffer read state" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 16.--19. " AXIWR ,Buffer manager AXI bus write state" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 15. " INBUFRD ,Indicates if BM input buffer is being read" "Not read,Read" textline " " bitfld.long 0x00 13.--14. " INBUFRDBMINDEX ,Indicate which BM is reading data from input buffer" "0,1,2,3" bitfld.long 0x00 8.--12. " INBUFRDBUFFERINDEX ,indicate which buffer is reading data from input buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x00 7. " INBUFWR ,Indicates if BM input buffer is being written" "No,Yes" textline " " bitfld.long 0x00 5.--6. " INBUFWRBMINDEX ,Indicate which BM is collecting data from TSD" "0,1,2,3" bitfld.long 0x00 0.--4. " INBUFWRBUFFERINDEX ,indicate which buffer is collecting data from TSD" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" elif ((((per.l(ad:0xC0000000+0x4505C8))&0x8000)==0x8000)&&(((per.l(ad:0xC0000000+0x4505C8))&0x80)==0x00)) rgroup.long 0x4505C8++0x03 line.long 0x00 "BM_STATUS,Debug register" bitfld.long 0x00 31. " AXIACTIVE ,Indicates if AXI bus access is active" "Not active,Avtive" bitfld.long 0x00 27.--28. " HCBRD ,Buffer manager HCB read state" "0,1,2,3" bitfld.long 0x00 24.--26. " AXIRD ,Buffer manager AXI bus read state" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 20.--23. " BMINBUFRD ,Buffer manager input buffer read state" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 16.--19. " AXIWR ,Buffer manager AXI bus write state" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 15. " INBUFRD ,Indicates if BM input buffer is being read" "Not read,Read" textline " " bitfld.long 0x00 13.--14. " INBUFRDBMINDEX ,Indicate which BM is reading data from input buffer" "0,1,2,3" bitfld.long 0x00 8.--12. " INBUFRDBUFFERINDEX ,indicate which buffer is reading data from input buffer" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x00 7. " INBUFWR ,Indicates if BM input buffer is being written" "No,Yes" elif ((((per.l(ad:0xC0000000+0x4505C8))&0x8000)==0x00)&&(((per.l(ad:0xC0000000+0x4505C8))&0x80)==0x80)) rgroup.long 0x4505C8++0x03 line.long 0x00 "BM_STATUS,Debug register" bitfld.long 0x00 31. " AXIACTIVE ,Indicates if AXI bus access is active" "Not active,Avtive" bitfld.long 0x00 27.--28. " HCBRD ,Buffer manager HCB read state" "0,1,2,3" bitfld.long 0x00 24.--26. " AXIRD ,Buffer manager AXI bus read state" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 20.--23. " BMINBUFRD ,Buffer manager input buffer read state" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 16.--19. " AXIWR ,Buffer manager AXI bus write state" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 15. " INBUFRD ,Indicates if BM input buffer is being read" "Not read,Read" textline " " bitfld.long 0x00 7. " INBUFWR ,Indicates if BM input buffer is being written" "No,Yes" bitfld.long 0x00 5.--6. " INBUFWRBMINDEX ,Indicate which BM is collecting data from TSD" "0,1,2,3" textline " " bitfld.long 0x00 0.--4. " INBUFWRBUFFERINDEX ,indicate which buffer is collecting data from TSD" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" else rgroup.long 0x4505C8++0x03 line.long 0x00 "BM_STATUS,Debug register" bitfld.long 0x00 31. " AXIACTIVE ,Indicates if AXI bus access is active" "Not active,Avtive" bitfld.long 0x00 27.--28. " HCBRD ,Buffer manager HCB read state" "0,1,2,3" bitfld.long 0x00 24.--26. " AXIRD ,Buffer manager AXI bus read state" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 20.--23. " BMINBUFRD ,Buffer manager input buffer read state" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 16.--19. " AXIWR ,Buffer manager AXI bus write state" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 15. " INBUFRD ,Indicates if BM input buffer is being read" "Not read,Read" textline " " bitfld.long 0x00 7. " INBUFWR ,Indicates if BM input buffer is being written" "No,Yes" endif tree.end tree.end width 0x0B tree.end sif (cpu()!="MB86R11F") tree "APIX_TX" tree "Channel 0" base ad:0x3A010000 width 31. group.long 0x00++0x07 line.long 0x00 "SWRESET,Resets APIX IP core" bitfld.long 0x00 0. " CFG_VALID ,cfg_valid" "Core in reset,Core enabled" line.long 0x04 "APIXMODE,General configuration register" bitfld.long 0x04 0. " APIX_MODE ,Apix mode" "APIX1,APIX2" group.long 0x08++0x0B line.long 0x00 "FIR_FILTER_0,Configuration for APIX transmitter FIR filter" bitfld.long 0x00 30. " C3SIGN ,Sign FIR coefficient c3" "0,1" bitfld.long 0x00 24.--29. " C3COEFF ,Value FIR coefficient c3" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x00 22. " C2SIGN ,Sign FIR coefficient c2" "0,1" bitfld.long 0x00 16.--21. " C2COEFF ,Value FIR coefficient c2" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x00 14. " C1SIGN ,Sign FIR coefficient c1" "0,1" bitfld.long 0x00 8.--13. " C1COEFF ,Value FIR coefficient c1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x00 6. " C0SIGN ,Sign FIR coefficient c0" "0,1" bitfld.long 0x00 0.--5. " C0COEFF ,Value FIR coefficient c0" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x04 "FIR_FILTER_1,Configuration for APIX transmitter FIR filter" bitfld.long 0x04 2.--4. " FIROUTCOEFF ,Defines the FIR output coefficients d4 d3 d2" "0,1,2,3,4,5,6,7" bitfld.long 0x04 0.--1. " FIRINCOEFF ,Defines the FIR input coefficients b3 b2" "0,1,2,3" line.long 0x08 "CALIB_I_TST_CFG,Calibration Test configuration" bitfld.long 0x08 31. " I_CALIB_EN ,Enable process compensation calibration" "Disabled,Enabled" rgroup.long 0x10++0x03 line.long 0x00 "CALIB_I_TST_STS,Calibration Test status" hexmask.long.word 0x00 16.--26. 1. " I_CALIB ,Internal comparator calibration value" hexmask.long.word 0x00 0.--8. 1. " I_CONTROL ,Process compensation value" group.long 0x14++0x03 line.long 0x00 "CALIB_P_TST_CFG,Calibration Prebuffer Test configuration" bitfld.long 0x00 31. " P_CALIB_EN ,Enable cable dependent calibration" "Disabled,Enabled" rgroup.long 0x18++0x03 line.long 0x00 "CALIB_P_TST_STS,Calibration Prebuffer Test status" hexmask.long.word 0x00 16.--26. 1. " P_CALIB ,Internal comparator calibration value" hexmask.long.word 0x00 0.--8. 1. " P_CONTROL ,Cable dependent calibration value" group.long 0x30++0x17 line.long 0x00 "LINKCFG,Configuration of different toplevel link functions" bitfld.long 0x00 8. " APIX1_GPIOREGEN ,Enables register access to APIX1 SBGIO port" "Disabled,Enabled" bitfld.long 0x00 7. " AICCONNECT1 ,Configuration for AIC 2:3 crossbar(AIC1)" "Disabled,Enabled" textline " " bitfld.long 0x00 6. " AICCONNECT0 ,Configuration for AIC 2:3 crossbar(AIC1)" "Disabled,Enabled" bitfld.long 0x00 4.--5. " AICMODE ,Selects data and direction for AIC pins" "Mode0 2bit AIC,Mode1 1bit AIC,Mode2 2bit AIC-2," textline " " bitfld.long 0x00 0. " PIXCH0SEL ,Selects pixel input for pixel channel 0 output" "Input 0,Input 1" line.long 0x04 "CH0PACKER_COLORCOMPONENTBITS,Color component size of outgoing pixel stream channel 0" bitfld.long 0x04 24.--27. " CH0COMPONENTBITSRED ,Number of red bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x04 16.--19. " CH0COMPONENTBITSGREEN ,Number of green bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x04 8.--11. " CH0COMPONENTBITSBLUE ,Number of blue bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "CH0PACKER_COLORCOMPONENTSHIFT,Color component offset of outgoing pixel stream channel 0" bitfld.long 0x08 24.--28. " CH0COMPONENTSHIFTRED ,Component Shift Red" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x08 16.--20. " CH0COMPONENTSHIFTGREEN ,Component Shift Green" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x08 8.--12. " CH0COMPONENTSHIFTBLUE ,Component Shift Blue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x0C "CH1PACKER_COLORCOMPONENTBITS,Color component size of outgoing pixel stream channel 1" bitfld.long 0x0C 24.--27. " CH1COMPONENTBITSRED ,Number of red bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x0C 16.--19. " CH1COMPONENTBITSGREEN ,Number of green bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x0C 8.--11. " CH1COMPONENTBITSBLUE ,Number of blue bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x10 "CH1PACKER_COLORCOMPONENTSHIFT,Color component offset of outgoing pixel stream channel 1" bitfld.long 0x10 24.--28. " CH1COMPONENTSHIFTRED ,Component Shift Red" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x10 16.--20. " CH1COMPONENTSHIFTGREEN ,Component Shift Green" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x10 8.--12. " CH1COMPONENTSHIFTBLUE ,Component Shift Blue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x14 "APIX12_CFG_0,Inova Config Byte 01" bitfld.long 0x14 0.--1. " DOWNBW ,Setting of the downstream bandwidth" ",M500mode,G1mode,G3mode" textline "" width 18. if (((per.l(ad:0x3A010000+0x04))&0x01)==0x01) group.long 0x48++0x03 line.long 0x00 "APIX12_CFG_2,Inova Config Bytes 0B_0A_09" bitfld.long 0x00 16.--17. " UPSPOFFSET750 ,Upstream sample point multiple of 750 MHz clock cycles" "0 cycles,1 cycles,2 cycles,3 cycles" bitfld.long 0x00 11.--12. " UPSPOFFSET ,Upstream sample point multiple of core clock after detect transitions" "0 cycles,1 cycles,2 cycles,3 cycles" textline " " bitfld.long 0x00 8.--9. " UPSERIALBW ,Upstream serial bandwidth" "APIX2_fast 187.5 Mbit/s,,APIX2_slow 62.5 Mbit/s," bitfld.long 0x00 5. " BACKPREN ,AShell back pressure enable" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " UPWDFAEN ,Watchdog upstream frame alignment" "Disabled,Enabled" bitfld.long 0x00 3. " UPWDBAEN ,Watchdog upstream bit alignment" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " CH1PIXEN ,Enable pixel channel1 in APIX2 core" "Disabled,Enabled" bitfld.long 0x00 0. " CH0PIXEN ,Enable pixel channel0 in APIX2 core" "Disabled,Enabled" else group.long 0x48++0x03 line.long 0x00 "APIX12_CFG_2,Inova Config Bytes 0B_0A_09" bitfld.long 0x00 16.--17. " UPSPOFFSET750 ,Upstream sample point multiple of 750 MHz clock cycles" "0 cycles,1 cycles,2 cycles,3 cycles" bitfld.long 0x00 11.--12. " UPSPOFFSET ,Upstream sample point multiple of core clock after detect transitions" "0 cycles,1 cycles,2 cycles,3 cycles" textline " " bitfld.long 0x00 8.--9. " UPSERIALBW ,Upstream serial bandwidth" ",APIX1_fast 62.5 Mbit/s,,APIX1_slow 31.25 Mbit/s" bitfld.long 0x00 5. " BACKPREN ,AShell back pressure enable" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " UPWDFAEN ,Watchdog upstream frame alignment" "Disabled,Enabled" bitfld.long 0x00 3. " UPWDBAEN ,Watchdog upstream bit alignment" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " CH1PIXEN ,Enable pixel channel1 in APIX2 core" "Disabled,Enabled" bitfld.long 0x00 0. " CH0PIXEN ,Enable pixel channel0 in APIX2 core" "Disabled,Enabled" endif group.long 0x50++0x03 line.long 0x00 "APIX2_CFG_1,Inova COnfig Bytes 10_0F_0E_0D" bitfld.long 0x00 31. " ASHELL2_1_BROADCASTEN ,Broadcast mode of AShell2_1" "Disabled,Enabled" bitfld.long 0x00 30. " ASHELL2_1_LINKERRORTOL ,Link error tolerance of AShell2_1" "0,1" textline " " bitfld.long 0x00 26.--29. " ASHELL2_1_CRCTOCNT ,CRC timeout counter of AShell2_1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 25. " ASHELL2_1_ARQ_DIS ,Disable ARQ of AShell2_1" "No,Yes" textline " " bitfld.long 0x00 24. " ASHELL2_1_EN ,AShell2_1 enable" "Disabled,Enabled" bitfld.long 0x00 23. " ASHELL2_0_BROADCASTEN ,Broadcast mode of AShell2_0" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " ASHELL2_0_LINKERRORTOL ,Link error tolerance of AShell2_0" "0,1" bitfld.long 0x00 18.--21. " ASHELL2_0_CRCTOCNT ,CRC timeout counter of AShell2_0" "Disabled,4,6,10,8,16,24,40,32,64,96,160,256,512,768,1280" textline " " bitfld.long 0x00 17. " ASHELL2_0_ARQ_DIS ,Disable ARQ of AShell2_0" "Yes,No" bitfld.long 0x00 16. " ASHELL2_0_EN ,AShell2_0 enable" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " AUDIOEN ,Audio Interface enable" "Disabled,Enabled" bitfld.long 0x00 10. " AUDIOBW ,Audio bandwidth" "Ordinary bandwidth,High bandwidth" textline " " bitfld.long 0x00 9. " RXDAISYCHAIN ,RX daisy chain" "1 Apix2 DC off,2 Apix2 DC on" if (((per.l(ad:0x3A010000+0x44))&0x03)==0x01) group.long 0x54++0x03 line.long 0x00 "APIX2_CFG_2,Inova Config Bytes 13_12_11" bitfld.long 0x00 22. " GPIODWNBW ,GPIO downstream bandwidth mode" "Low speed,High speed" bitfld.long 0x00 21. " GPIODWNHALFBW ,Halve GPIO downstream bandwidth" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " GPIOUPBW ,GPIO upstream bandwidth mode" "Low speed,High speed" textline " " bitfld.long 0x00 19. " GPIO0UPEN ,GPIO0 upstream channel enable" "Disabled,Enabled" bitfld.long 0x00 18. " GPIO1UPEN ,GPIO1 upstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " GPIO0DWNEN ,GPIO0 downstream channel enable" "Disabled,Enabled" bitfld.long 0x00 16. " GPIO1DWNEN ,GPIO1 downstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 14.--15. " ASH2DWNDIV ,AShell2 downstream bandwidth divider" "/1,/2,/4,/8" bitfld.long 0x00 9.--13. " DOWNDATABW ,Totally available downstream bandwidth for AShell data audio and GPIO" ",56 MBit/s,42 MBit/s,,29 MBit/s,,,,15 MBit/s,,,,,,,,1.3 MBit/s,..." textline " " bitfld.long 0x00 6. " BULKDATAEN ,Bulk data mode" "Disabled,Enabled" bitfld.long 0x00 5. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24bits,21 bits" textline " " bitfld.long 0x00 3.--4. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "BpP10,BpP12,BpP18,BpP24" bitfld.long 0x00 2. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24bits,21bits" textline " " bitfld.long 0x00 0.--1. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "BpP10,BpP12,BpP18,BpP24" elif (((per.l(ad:0x3A010000+0x44))&0x03)==0x02) group.long 0x54++0x03 line.long 0x00 "APIX2_CFG_2,Inova Config Bytes 13_12_11" bitfld.long 0x00 22. " GPIODWNBW ,GPIO downstream bandwidth mode" "Low speed,High speed" bitfld.long 0x00 21. " GPIODWNHALFBW ,Halve GPIO downstream bandwidth" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " GPIOUPBW ,GPIO upstream bandwidth mode" "Low speed,High speed" textline " " bitfld.long 0x00 19. " GPIO0UPEN ,GPIO0 upstream channel enable" "Disabled,Enabled" bitfld.long 0x00 18. " GPIO1UPEN ,GPIO1 upstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " GPIO0DWNEN ,GPIO0 downstream channel enable" "Disabled,Enabled" bitfld.long 0x00 16. " GPIO1DWNEN ,GPIO1 downstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 14.--15. " ASH2DWNDIV ,AShell2 downstream bandwidth divider" "/1,/2,/4,/8" bitfld.long 0x00 9.--13. " DOWNDATABW ,Totally available downstream bandwidth for AShell data audio and GPIO" ",113 MBit/s,85 MBit/s,,58 MBit/s,,,,30 MBit/s,..." textline " " bitfld.long 0x00 6. " BULKDATAEN ,Bulk data mode" "Disabled,Enabled" bitfld.long 0x00 5. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24bits,21 bits" textline " " bitfld.long 0x00 3.--4. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "10bit per pixel,12bit per pixel,18bit per pixel,24" bitfld.long 0x00 2. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24bits,21bits" textline " " bitfld.long 0x00 0.--1. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "10bit per pixel,12bit per pixel,18bit per pixel,24" elif (((per.l(ad:0x3A010000+0x44))&0x03)==0x03) group.long 0x54++0x03 line.long 0x00 "APIX2_CFG_2,Inova Config Bytes 13_12_11" bitfld.long 0x00 22. " GPIODWNBW ,GPIO downstream bandwidth mode" "Low speed,High speed" bitfld.long 0x00 21. " GPIODWNHALFBW ,Halve GPIO downstream bandwidth" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " GPIOUPBW ,GPIO upstream bandwidth mode" "Low speed,High speed" textline " " bitfld.long 0x00 19. " GPIO0UPEN ,GPIO0 upstream channel enable" "Disabled,Enabled" bitfld.long 0x00 18. " GPIO1UPEN ,GPIO1 upstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " GPIO0DWNEN ,GPIO0 downstream channel enable" "Disabled,Enabled" bitfld.long 0x00 16. " GPIO1DWNEN ,GPIO1 downstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 14.--15. " ASH2DWNDIV ,AShell2 downstream bandwidth divider" "/1,/2,/4,/8" bitfld.long 0x00 9.--13. " DOWNDATABW ,Totally available downstream bandwidth for AShell data audio and GPIO" ",340 MBit/s,257 MBit/s,,174 MBit/s,,,,91 MBit/s,..." textline " " bitfld.long 0x00 6. " BULKDATAEN ,Bulk data mode" "Disabled,Enabled" bitfld.long 0x00 5. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24bits,21 bits" textline " " bitfld.long 0x00 3.--4. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "BpP10,BpP12,BpP18,BpP24" bitfld.long 0x00 2. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24bits,21bits" textline " " bitfld.long 0x00 0.--1. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "BpP10,BpP12,BpP18,BpP24" else group.long 0x54++0x03 line.long 0x00 "APIX2_CFG_2,Inova Config Bytes 13_12_11" bitfld.long 0x00 22. " GPIODWNBW ,GPIO downstream bandwidth mode" "Low speed,High speed" bitfld.long 0x00 21. " GPIODWNHALFBW ,Halve GPIO downstream bandwidth" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " GPIOUPBW ,GPIO upstream bandwidth mode" "Low speed,High speed" textline " " bitfld.long 0x00 19. " GPIO0UPEN ,GPIO0 upstream channel enable" "Disabled,Enabled" bitfld.long 0x00 18. " GPIO1UPEN ,GPIO1 upstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " GPIO0DWNEN ,GPIO0 downstream channel enable" "Disabled,Enabled" bitfld.long 0x00 16. " GPIO1DWNEN ,GPIO1 downstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 14.--15. " ASH2DWNDIV ,AShell2 downstream bandwidth divider" "/1,/2,/4,/8" textline " " bitfld.long 0x00 6. " BULKDATAEN ,Bulk data mode" "Disabled,Enabled" bitfld.long 0x00 5. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24bits,21 bits" textline " " bitfld.long 0x00 3.--4. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "BpP10,BpP12,BpP18,BpP24" bitfld.long 0x00 2. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24bits,21bits" textline " " bitfld.long 0x00 0.--1. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "BpP10,BpP12,BpP18,BpP24" endif group.long 0x58++0x17 line.long 0x00 "APIX1_CFG_0,Inova Config Byte 14" hexmask.long.byte 0x00 24.--30. 1. " SBDOWN_DATA_CYCLETIME6TO0 ,Cycle time of sbdown clock in multiples of 8ns" line.long 0x04 "APIX1_CFG_1,Inova Config Bytes 18_17_16_15" bitfld.long 0x04 27.--28. " PX_CTRL_PIGGYBACK ,APIX PHY (Soft IP): transmission of pixel controls" "Never,Unused,With even pixels only,With every pixel" bitfld.long 0x04 25.--26. " PIXEL_DATA_WIDTH ,Pixel data width" "10bit per pixel,12bit per pixel,18bit per pixel,24" textline " " bitfld.long 0x04 23. " ARQ_DISABLE ,Retransmission disable" "No,Yes" bitfld.long 0x04 22. " SUPPRESS_IDLE ,Suppress idle transmission to reduce data traffic" "Disabled,Enabled" textline " " bitfld.long 0x04 16.--18. " SBDOWN_DATA_CYCLETIME9TO7 ,Upper bits of sbdown_data_cycletime" "0,1,2,3,4,5,6,7" bitfld.long 0x04 12.--15. " CRC_TIME_OUT_VALUE ,CRC timeout value" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x04 8.--11. " WINDOW_SIZE ,AShell window size Window size of the retransmission protocol" ",1,2,3,4,5,6,7,8,9,10,11,12,,," bitfld.long 0x04 7. " SBUP_DWIDTH ,Enable sbup data ports" "1 bit,2 bit" textline " " bitfld.long 0x04 6. " SBUP_DACLK ,Validate sbup_data automatic or with transmitted valid" "Disabled,Enabled" bitfld.long 0x04 5. " SBDOWN_DWIDTH ,Enable sbdown data ports" "1 bit data and valid,2 bit data" textline " " bitfld.long 0x04 3.--4. " SBDOWN_DACLK ,Generate sbdown clock and transmit as sbdown_data[1]" ",Sbdown_trigger,Internal counter," bitfld.long 0x04 1. " ESHELLEN ,Connect internal APIX1 PHY to external sideband data through APIX1 SBGPIO (AIC) interface" "Disabled,Enabled" textline " " bitfld.long 0x04 0. " SPI_OVER_SB ,Selects between two different sideband transmission modes" "Full data mode,SPI mode" line.long 0x08 "APIX1_CFG_2,Inova Config Bytes 1C_1B_1A_19" hexmask.long.byte 0x08 25.--31. 1. " SBDOWN_CLOCK_HIGH_PULSE ,Configure high pulse width of signal 'sb_down_clk' if sb_down_clk and sb_up_clk enable" hexmask.long.byte 0x08 17.--23. 1. " SBDOWN_CLOCK_CYCLES ,Configures sbdown clk cycle" textline " " bitfld.long 0x08 15. " DDOWN_ENABLE ,APIX PHY (Soft IP) / AShell: configure downstream data path" "Pixel stream mode,Data mode" bitfld.long 0x08 14. " EXT_SB_DATA_DIS ,Sideband data are 2-stage registered internal have to be used with external sideband data" "External,No external" textline " " bitfld.long 0x08 11. " ASHELL1_EN ,APIX1 Ashell1" "Disabled,Enabled" bitfld.long 0x08 10. " SB_CLK_EN ,Enable sb_down_clk and sb_up_clk" "Disabled,Enabled" textline " " bitfld.long 0x08 8.--9. " SB_UP_CLK_CYCLES ,Configure high pulse width of signal 'sb_up_clk' if sb_down_clk and sb_up_clk enable" "1cycle,2cycles,3cysles,4cycles" line.long 0x0C "APIX1_CFG_3,Inova Config Byte 1D" hexmask.long.byte 0x0C 1.--7. 1. " SBDOWN_CLOCK_START_POS ,Start position of signal sbdown_clk relative to internal \u2018strobe position\u2019" line.long 0x10 "TEST_CONFIG,Config for Inova BIST Test" hexmask.long.word 0x10 16.--31. 1. " TEST_PATTERN ,Test pattern" bitfld.long 0x10 12. " TESTPATTERN_EN ,Test pattern generation" "Disabled,Enabled" textline " " bitfld.long 0x10 11. " PSRTEST_MODE ,PSR test pattern generation" "Disabled,Enabled" bitfld.long 0x10 9.--10. " PSRTEST_8B10B ,Psr Test 8B10B" "Run length 8,Run length 10,Run length 12,Run length 16" textline " " bitfld.long 0x10 8. " BG_MASK_DISABLE ,Line coder mask disable" "No,Yes" line.long 0x14 "AAC,Configuration for AShell1-to-AShell1 - Connector (AAC)" bitfld.long 0x14 14.--15. " AACOFFSET ,Cfg_data[15:14] offset between edges of AAC clock and AAC data[1:0] as multiples of core clock" "1cycle,2cycles,3cycles,4cycles" hexmask.long.word 0x14 2.--13. 1. " AACFREQUENCY ,Defines AAC clock frequency" textline " " bitfld.long 0x14 1. " AACEN ,Data path selection" "APIX1 PHY,ACC" bitfld.long 0x14 0. " AACMODE ,AAC clock mode" "Both edges,Rising edges" group.long 0x70++0x0B line.long 0x00 "AAA,Configuration for Ashell1-to-Ashell2 Adapter" bitfld.long 0x00 1. " AAAEN ,AShell1 to AShell2 Adapter enable" "Disabled,Enabled" bitfld.long 0x00 0. " ASHELL2_SELECT ,Ashell2 select" "AShell2_1,AShell2_0" line.long 0x04 "APIX1_GPO,GPIO DATA for APIX1 communication" bitfld.long 0x04 0.--1. " APIX1_GPO ,2 bit GPIO output data corresponds to GPIO pins of INAP1 device" "0,1,2,3" line.long 0x08 "APIX1_GPI_INTCFG,APIX1GPI INTCFG" bitfld.long 0x08 1. " APIX1_GPI_INTCFG ,APIX1_GPI_INTCFG" "Rising edge,Falling edge" bitfld.long 0x08 0. " APIX0_GPI_INTCFG ,APIX0_GPI_INTCFG" "Rising edge,Falling edge" rgroup.long 0x7C++0x03 line.long 0x00 "APIX1_GPI,GPIO DATA for APIX1 communication" bitfld.long 0x00 0.--1. " APIX1_GP1 ,2 bit GPIO output data corresponds to GPIO pins of INAP1 device" "0,1,2,3" group.long 0x80++0x07 line.long 0x00 "APIX2_GPO,GPIO DATA for APIX2 communication" bitfld.long 0x00 0.--1. " APIX2_GPO ,2 bit GPIO output data corresponds to GPIO pins of INAP1 device" "0,1,2,3" line.long 0x04 "APIX2_GPI_INTCFG,APIX2_GPI_INTCFG" bitfld.long 0x04 3. " APIX2_GPI_INTCFG[3] ,APIX2_GPI_INTCFG[3]" "Rising edge,Falling edge" bitfld.long 0x04 2. " APIX2_GPI_INTCFG[2] ,APIX2_GPI_INTCFG[2]" "Rising edge,Falling edge" textline " " bitfld.long 0x04 1. " APIX2_GPI_INTCFG[1] ,APIX2_GPI_INTCFG[1]" "Rising edge,Falling edge" bitfld.long 0x04 0. " APIX2_GPI_INTCFG[0] ,APIX2_GPI_INTCFG[0]" "Rising edge,Falling edge" rgroup.long 0x88++0x03 line.long 0x00 "APIX2_GPI,GPIO DATA for APIX2 communication" bitfld.long 0x00 0.--3. " APIX2_GPI ,2 bit GPIO input data, corresponds to GPIO pins of INAP1 device" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" group.long 0x200++0x07 line.long 0x00 "APIX_CTRL_0,Signals to AShell restart and counter clears" eventfld.long 0x00 4. " ASHELL2_1_TCNT_CLEAR ,AShell2_1_tcnt_clear" "Not clear,Clear" eventfld.long 0x00 3. " ASHELL2_0_TCNT_CLEAR ,AShell2_0_tcnt_clear" "Not clear,Clear" textline " " eventfld.long 0x00 2. " ASHELL1_REALIGN ,Apix1 AShell realign by writing a 1" "Not realign,Realign" eventfld.long 0x00 1. " ASHELL2_1_REALIGN ,AShell2_1 realign by writing a 1" "Not realign,Realign" textline " " eventfld.long 0x00 0. " ASHELL2_0_REALIGN ,AShell2_0 realign by writing a 1" "Not realign,Realign" line.long 0x04 "APIX_CTRL_1,Reset for counter values" eventfld.long 0x04 5. " ASHELL2_0_CRCERRCNTCLEAR ,Clear Ashell2_0_CRCErrCnt by writing a 1" "Not clear,Clear" eventfld.long 0x04 4. " ASHELL2_1_CRCERRCNTCLEAR ,Clear Ashell2_1_CRCErrCnt by writing a 1" "Not clear,Clear" textline " " eventfld.long 0x04 3. " APIX1UPFALIGNERRCNTCLEAR ,Clear Apix1upFAlignErrCnt by writing a 1" "Not clear,Clear" eventfld.long 0x04 2. " ASHELL1_CRCERRCNTCLEAR ,Clear Ashell2_1_CRCErrCnt by writing a 1" "Not clear,Clear" textline " " eventfld.long 0x04 1. " APIX2UPFALIGNERRCNTCLEAR ,Clear Apix2upFAlignErrCnt by writing a 1" "Not clear,Clear" group.long 0x208++0x0B line.long 0x00 "APIX12_STATUS_0,Status from Inova Status bytes 01 and 02 PHY status pixelstream status" rbitfld.long 0x00 12. " APIX2UPFALIGN ,Apix2 upstream frame aligned" "No,Yes" rbitfld.long 0x00 8.--11. " APIX2UPFALIGNERRCNT ,APIX2 upstream frame aligned error counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 0. " UPBITALIGNED ,Upstream bit aligned" "0,1" line.long 0x04 "APIX2_STATUS_0,Status from Inova Status bytes 06_05_04_03 Pixelstream status Ashell2_0 Status" hexmask.long.byte 0x04 24.--31. 1. " ASHELL2_0_TADIFFCNT ,Transaction counter difference of AShell2_0" rbitfld.long 0x04 17. " ASHELL2_0_OPERATIONAL ,AShell operational" "Not asserted,Asserted" textline " " hexmask.long.byte 0x04 8.--15. 1. " ASHELL2_0_CRCERRCNT ,CRC error counter of AShell2_0" rbitfld.long 0x04 7. " CH1HSYNCPOL ,Pixel channel 1 horizontal polarity" "Active low,Active high" textline " " rbitfld.long 0x04 6. " CH1VSYNCPOL ,Pixel channel 1 vertical polarity" "Active low,Active high" rbitfld.long 0x04 5. " CH1PIXFIFOEMPTY ,Pixel channel 1 FIFO underflow" "No,Yes" textline " " rbitfld.long 0x04 4. " CH1PIXFIFOFULL ,Pixel channel 1 FIFO overflow" "No,Yes" rbitfld.long 0x04 3. " CH0HSYNCPOL ,Pixel channel 0 horizontal polarity" "Active low,Active high" textline " " rbitfld.long 0x04 2. " CH0VSYNCPOL ,Pixel channel 0 vertical polarity" "Active low,Active high" rbitfld.long 0x04 1. " CH0PIXFIFOEMPTY ,Pixel channel 0 FIFO underflow" "No,Yes" textline " " bitfld.long 0x04 0. " CH0PIXFIFOFULL ,Pixel channel 0 FIFO overflow" "No,Yes" line.long 0x08 "APIX2_STATUS_1,Status from Inova Status bytes 09_08_07 Ashell2_1 status" hexmask.long.byte 0x08 24.--31. 1. " ASHELL2_1_TADIFFCNT ,Transaction counter difference of AShell2_1" rbitfld.long 0x08 17. " ASHELL2_1_OPERATIONAL ,AShell operational" "Not asserted,Asserted" textline " " hexmask.long.byte 0x08 8.--15. 1. " ASHELL2_1_CRCERRCNT ,CRC error counter of AShell2_0 Number of received CRC errors" rgroup.long 0x214++0x03 line.long 0x00 "APIX1_STATUS_0,Status from Inova Status bytes 0C_0B_0A Ashell1 and APIX1 PHY" bitfld.long 0x00 22. " APIX1UPFRAMEALIGNED ,Apix1 upstream frame aligned" "No,Yes" bitfld.long 0x00 16.--21. " APIX1UPFRAMEALIGNEDERRCNT ,Apix1 upstream frame aligned error counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x00 8.--13. " ASHELL1_CRCERRCNT ,Apix1 AShell CRC error counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 6. " ASHELL1_OPERATIONAL ,Apix1 AShell operational" "Not asserted,Asserted" tree "Interrupt registers" width 13. rgroup.long 0x300++0x0B line.long 0x00 "INTSTATUS0,Interrupt Status Register 0" bitfld.long 0x00 31. " RX1_REMOTE_INBOUND_I2C_JOB_CANCEL ,APIX2 Remote command cancel I2C job received from device RX1" "Inactive,Active" bitfld.long 0x00 30. " RX1_REMOTE_INBOUND_ASHELL2_CLEAR_TICKET_COUNTER ,APIX2 Remote command clear Ashell2 ticket counter received from device RX1" "Inactive,Active" textline " " bitfld.long 0x00 29. " RX1_REMOTE_INBOUND_ASHELL2_REALIGN ,APIX2 Remote command realign Ashell2 received from device RX1" "Inactive,Active" bitfld.long 0x00 28. " RX1_REMOTE_INBOUND_SOFT_RESET ,APIX2 Remote command soft reset received from device RX1" "Inactive,Active" textline " " bitfld.long 0x00 27. " RX0_REMOTE_INBOUND_I2C_JOB_CANCEL ,APIX2 Remote command cancel I2C job received from device RX0" "Inactive,Active" bitfld.long 0x00 26. " RX0_REMOTE_INBOUND_ASHELL2_CLEAR_TICKET_COUNTER ,APIX2 Remote command clear Ashell2 ticket counter received from device RX0" "Inactive,Active" textline " " bitfld.long 0x00 25. " RX0_REMOTE_INBOUND_ASHELL2_REALIGN ,APIX2 Remote command realign Ashell2 received from device RX0" "Inactive,Active" bitfld.long 0x00 24. " RX0_REMOTE_INBOUND_SOFT_RESET ,APIX2 Remote command soft reset received from device RX0" "Inactive,Active" textline " " bitfld.long 0x00 23. " GPI_1 ,APIX1 GPIO Edge detected at APIX1 GPI_1 port" "Inactive,Active" bitfld.long 0x00 22. " GPI_0 ,APIX1 GPIO Edge detected at APIX1 GPI_0 port" "Inactive,Active" textline " " bitfld.long 0x00 21. " ASHELL1_FATAL ,APIX1 Ashell1 Fatal Error" "Inactive,Active" bitfld.long 0x00 20. " ASHELL1_CRCERROR ,APIX1 Ashell1 detected CRC error at incoming data" "Inactive,Active" textline " " bitfld.long 0x00 19. " ASHELL1_UNCONNECTED ,APIX1 Ashell1 unconnected with remote Ashell" "Inactive,Active" bitfld.long 0x00 18. " ASHELL1_CONNECTED ,APIX1 Ashell1 connected with remote Ashell" "Inactive,Active" textline " " bitfld.long 0x00 17. " ASHELL1_CRCTIMEOUT ,APIX1 Ashell1 CRC error threshold was reached" "Inactive,Active" bitfld.long 0x00 16. " ASHELL1_PROTERR ,APIX1 Ashell1 Protocoll Error" "Inactive,Active" textline " " bitfld.long 0x00 15. " ASHELL1_REMRESTARTED ,APIX1 Ashell1 Remote Ashell1 was restarted" "Inactive,Active" bitfld.long 0x00 14. " ASHELL2_1_UNCONNECTED ,APIX2 Ashell2_1 unconnected with remote Ashell" "Inactive,Active" textline " " bitfld.long 0x00 13. " ASHELL2_1_CONNECTED ,APIX2 Ashell2_1 connected with remote Ashell" "Inactive,Active" bitfld.long 0x00 12. " ASHELL2_1_TRANSACTION_LOSS ,APIX2 Ashell2_1 Transaction Loss Error" "Inactive,Active" textline " " bitfld.long 0x00 11. " ASHELL2_1_FATAL ,APIX2 Ashell2_1 Fatal Error" "Inactive,Active" bitfld.long 0x00 10. " ASHELL2_1_CRCERROR ,APIX2 Ashell2_1 CRC error" "Inactive,Active" textline " " bitfld.long 0x00 9. " ASHELL2_0_UNCONNECTED ,APIX2 Ashell2_0 unconnected with remote Ashell" "Inactive,Active" bitfld.long 0x00 8. " ASHELL2_0_CONNECTED ,APIX2 Ashell2_0 connected with remote Ashell" "Inactive,Active" textline " " bitfld.long 0x00 7. " ASHELL2_0_TRANSACTION_LOSS ,APIX2 Ashell2_0 Transaction Loss Error" "Inactive,Active" bitfld.long 0x00 6. " ASHELL2_0_FATAL ,APIX2 Ashell2_0 Fatal Error" "Inactive,Active" textline " " bitfld.long 0x00 5. " ASHELL2_0_CRCERROR ,APIX2 Ashell2_0 CRC error" "Inactive,Active" bitfld.long 0x00 4. " CH0PIXFIFOFULL_INT ,APIX2 PIX Channel 0 pixelfifo overflow error" "Inactive,Active" textline " " bitfld.long 0x00 3. " CH0PIXFIFOEMPTY_INT ,APIX2 PIX Channel 0 pixelfiifo underflow error" "Inactive,Active" bitfld.long 0x00 2. " CH1PIXFIFOFULL_INT ,APIX2 PIX Channel 1 pixelfifo overflow error" "Inactive,Active" textline " " bitfld.long 0x00 1. " CH1PIXFIFOEMPTY_INT ,APIX2 PIX Channel 1 pixelfiifo underflow error" "Inactive,Active" bitfld.long 0x00 0. " UPBITALIGNEDLOSS ,PHY Loss of upstream PHY Bit alignment" "Inactive,Active" line.long 0x04 "INTSTATUS1,Interrupt Status Register 1" bitfld.long 0x04 31. " RX1_REMOTE_SERVICE_INBOUND_ERROR_INT ,APIX2 remote IF Data loss at inbound remote service data register (Rx1)" "Inactive,Active" bitfld.long 0x04 30. " RX1_REMOTE_SERVICE_INBOUND_VALID_INT ,APIX2 remote IF Received valid inbound data from remote service IF of device RX1" "Inactive,Active" textline " " bitfld.long 0x04 29. " RX1_REMOTE_CONTROLLER_INBOUND_ERROR_INT ,APIX2 remote IF Data loss at inbound remote control data register (RX1)" "Inactive,Active" bitfld.long 0x04 28. " RX1_REMOTE_CONTROLLER_INBOUND_VALID_INT ,APIX2 remote IF Received valid inbound data from remote control IF of device RX1" "Inactive,Active" textline " " bitfld.long 0x04 27. " RX0_REMOTE_SERVICE_INBOUND_ERROR_INT ,APIX2 remote IF Data loss at inbound remote service data register (Rx0)" "Inactive,Active" bitfld.long 0x04 26. " RX0_REMOTE_SERVICE_INBOUND_VALID_INT ,APIX2 remote IF Received valid inbound data from remote service IF of device RX0" "Inactive,Active" textline " " bitfld.long 0x04 25. " RX0_REMOTE_CONTROLLER_INBOUND_ERROR_INT ,APIX2 remote IF Data loss at inbound remote control data register (RX0)" "Inactive,Active" bitfld.long 0x04 24. " RX0_REMOTE_CONTROLLER_INBOUND_VALID_INT ,APIX2 remote IF Received valid inbound data from remote control IF of device RX0" "Inactive,Active" textline " " bitfld.long 0x04 23. " RX1_I2C_INBOUND_READ_RESPONSE_ERROR_INT ,APIX2 remote IF Data loss at i2c inbound read response register (RX1)" "Inactive,Active" bitfld.long 0x04 22. " RX1_I2C_INBOUND_READ_RESPONSE_VALID_INT ,APIX2 I2C Received valid inbound I2C read response from device RX1" "Inactive,Active" textline " " bitfld.long 0x04 21. " RX1_I2C_INBOUND_STATUS_ERROR_INT ,APIX2 I2C Data loss at inbound i2c status register (RX1)" "Inactive,Active" bitfld.long 0x04 20. " RX1_I2C_INBOUND_STATUS_VALID_INT ,APIX2 I2C Received valid inbound i2c status from device RX1" "Inactive,Active" textline " " bitfld.long 0x04 19. " RX1_I2C_INBOUND_JOB_SPEC_ERROR_INT ,APIX2 I2C Data loss at i2c job specification register (RX1)" "Inactive,Active" bitfld.long 0x04 18. " RRX1_I2C_INBOUND_JOB_SPEC_VALID_INT ,APIX2 I2C Received valid inbound i2c job specification from device RX1" "Inactive,Active" textline " " bitfld.long 0x04 17. " RX0_I2C_INBOUND_READ_RESPONSE_ERROR_INT ,APIX2 I2C Data loss at i2c inbound read response register (RX0)" "Inactive,Active" bitfld.long 0x04 16. " RX0_I2C_INBOUND_READ_RESPONSE_VALID_INT ,APIX2 I2C Received valid inbound I2C read response from device RX0" "Inactive,Active" textline " " bitfld.long 0x04 15. " RX0_I2C_INBOUND_STATUS_ERROR_INT ,APIX2 I2C Data loss at inbound i2c status register (RX0)" "Inactive,Active" bitfld.long 0x04 14. " RX0_I2C_INBOUND_STATUS_VALID_INT ,APIX2 I2C Received valid inbound i2c status from device RX0" "Inactive,Active" textline " " bitfld.long 0x04 13. " RX0_I2C_INBOUND_JOB_SPEC_ERROR_INT ,APIX2 I2C Data loss at i2c job specification register (RX0)" "Inactive,Active" bitfld.long 0x04 12. " RX0_I2C_INBOUND_JOB_SPEC_VALID_INT ,APIX2 I2C Received valid inbound i2c job specification from device RX0" "Inactive,Active" textline " " bitfld.long 0x04 11. " WDG_TIMEOUT_INT ,Message buffer Wrbuf Watchdog timeout" "Inactive,Active" bitfld.long 0x04 10. " WRBUF_EMPTY_INT ,Message buffer Write buffer #1 becomes empty" "Inactive,Active" textline " " bitfld.long 0x04 9. " WRBUF_FULL_INT ,Message buffer Write buffer #1 becomes full" "Inactive,Active" bitfld.long 0x04 8. " R1BUF_NOT_EMPTY ,Message buffer Read buffer #1 becomes not empty" "Inactive,Active" textline " " bitfld.long 0x04 7. " R1BUF_FULL_INT ,Message buffer Read buffer #1 becomes full" "Inactive,Active" bitfld.long 0x04 6. " R0BUF_NOT_EMPTY ,Message buffer Read buffer #0 becomes not empty" "Inactive,Active" textline " " bitfld.long 0x04 5. " R0BUF_FULL_INT ,Message buffer Read buffer #0 becomes full" "Inactive,Active" bitfld.long 0x04 4. " WRBUF_OVERFLOW ,Message buffer Write buffer overflow" "Inactive,Active" textline " " bitfld.long 0x04 3. " R1BUF_UNDERRUN ,Message buffer Read buffer #1 underrun" "Inactive,Active" bitfld.long 0x04 2. " R1BUF_OVERFLOW ,Message buffer Read buffer #1 overflow" "Inactive,Active" textline " " bitfld.long 0x04 1. " R0BUF_UNDERRUN ,Message buffer Read buffer #0 underrun" "Inactive,Active" bitfld.long 0x04 0. " R0BUF_OVERFLOW ,Message buffer Read buffer #0 overflow" "Inactive,Active" line.long 0x08 "INTSTATUS2,Interrupt Status Register 2" bitfld.long 0x08 6. " FRAME_ALIGNMENT_TIMEOUT_DETECT ,PHY signalizes that the device was not frame aligned" "Inactive,Active" bitfld.long 0x08 5. " DEBUG_TIMEOUT ,APIX2TX_link Abort of read access to debug register happened" "Inactive,Active" textline " " bitfld.long 0x08 4. " STATUS_TIMEOUT ,APIX2TX_link Abort of read access to status register happened" "Inactive,Active" bitfld.long 0x08 3. " APIX2_GPI_1_RX1 ,APIX2 GPIO Rising or falling edge detected at APIX2 GPI1 from device RX1" "Inactive,Active" textline " " bitfld.long 0x08 2. " APIX2_GPI_0_RX1 ,APIX2 GPIO Rising or falling edge detected at APIX2 GPI0 from device RX1" "Inactive,Active" bitfld.long 0x08 1. " APIX2_GPI_1_RX0 ,APIX2 GPIO Rising or falling edge detected at APIX2 GPI1 from device RX0" "Inactive,Active" textline " " bitfld.long 0x08 0. " APIX2_GPI_0_RX0 ,APIX2 GPIO Rising or falling edge detected at APIX2 GPI0 from device RX0" "Inactive,Active" textline "" ;section group.long 0x30C++0x2F line.long 0x00 "INT0ENABLE0,Interrupt Enable Register 0 for interrupts bits" bitfld.long 0x00 31. " INT0ENABLE0_[31] ,Interrupt 0 Enable bit 31" "Disabled,Enabled" bitfld.long 0x00 30. " [30] ,Interrupt 0 Enable bit 30" "Disabled,Enabled" bitfld.long 0x00 29. " [29] ,Interrupt 0 Enable bit 29" "Disabled,Enabled" bitfld.long 0x00 28. " [28] ,Interrupt 0 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x00 27. " [27] ,Interrupt 0 Enable bit 27" "Disabled,Enabled" bitfld.long 0x00 26. " [26] ,Interrupt 0 Enable bit 26" "Disabled,Enabled" bitfld.long 0x00 25. " [25] ,Interrupt 0 Enable bit 25" "Disabled,Enabled" bitfld.long 0x00 24. " [24] ,Interrupt 0 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x00 23. " [23] ,Interrupt 0 Enable bit 23" "Disabled,Enabled" bitfld.long 0x00 22. " [22] ,Interrupt 0 Enable bit 22" "Disabled,Enabled" bitfld.long 0x00 21. " [21] ,Interrupt 0 Enable bit 21" "Disabled,Enabled" bitfld.long 0x00 20. " [20] ,Interrupt 0 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " [19] ,Interrupt 0 Enable bit 19" "Disabled,Enabled" bitfld.long 0x00 18. " [18] ,Interrupt 0 Enable bit 18" "Disabled,Enabled" bitfld.long 0x00 17. " [17] ,Interrupt 0 Enable bit 17" "Disabled,Enabled" bitfld.long 0x00 16. " [16] ,Interrupt 0 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x00 15. " [15] ,Interrupt 0 Enable bit 15" "Disabled,Enabled" bitfld.long 0x00 14. " [14] ,Interrupt 0 Enable bit 14" "Disabled,Enabled" bitfld.long 0x00 13. " [13] ,Interrupt 0 Enable bit 13" "Disabled,Enabled" bitfld.long 0x00 12. " [12] ,Interrupt 0 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " [11] ,Interrupt 0 Enable bit 11" "Disabled,Enabled" bitfld.long 0x00 10. " [10] ,Interrupt 0 Enable bit 10" "Disabled,Enabled" bitfld.long 0x00 9. " [9] ,Interrupt 0 Enable bit 9" "Disabled,Enabled" bitfld.long 0x00 8. " [8] ,Interrupt 0 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " [7] ,Interrupt 0 Enable bit 7" "Disabled,Enabled" bitfld.long 0x00 6. " [6] ,Interrupt 0 Enable bit 6" "Disabled,Enabled" bitfld.long 0x00 5. " [5] ,Interrupt 0 Enable bit 5" "Disabled,Enabled" bitfld.long 0x00 4. " [4] ,Interrupt 0 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " [3] ,Interrupt 0 Enable bit 3" "Disabled,Enabled" bitfld.long 0x00 2. " [2] ,Interrupt 0 Enable bit 2" "Disabled,Enabled" bitfld.long 0x00 1. " [1] ,Interrupt 0 Enable bit 1" "Disabled,Enabled" bitfld.long 0x00 0. " [0] ,Interrupt 0 Enable bit 0" "Disabled,Enabled" line.long 0x04 "INT0ENABLE1,Interrupt Enable Register 1 for interrupts bits" bitfld.long 0x04 31. " INT0ENABLE1_[31] ,Interrupt 0 Enable bit 31" "Disabled,Enabled" bitfld.long 0x04 30. " [30] ,Interrupt 0 Enable bit 30" "Disabled,Enabled" bitfld.long 0x04 29. " [29] ,Interrupt 0 Enable bit 29" "Disabled,Enabled" bitfld.long 0x04 28. " [28] ,Interrupt 0 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x04 27. " [27] ,Interrupt 0 Enable bit 27" "Disabled,Enabled" bitfld.long 0x04 26. " [26] ,Interrupt 0 Enable bit 26" "Disabled,Enabled" bitfld.long 0x04 25. " [25] ,Interrupt 0 Enable bit 25" "Disabled,Enabled" bitfld.long 0x04 24. " [24] ,Interrupt 0 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x04 23. " [23] ,Interrupt 0 Enable bit 23" "Disabled,Enabled" bitfld.long 0x04 22. " [22] ,Interrupt 0 Enable bit 22" "Disabled,Enabled" bitfld.long 0x04 21. " [21] ,Interrupt 0 Enable bit 21" "Disabled,Enabled" bitfld.long 0x04 20. " [20] ,Interrupt 0 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x04 19. " [19] ,Interrupt 0 Enable bit 19" "Disabled,Enabled" bitfld.long 0x04 18. " [18] ,Interrupt 0 Enable bit 18" "Disabled,Enabled" bitfld.long 0x04 17. " [17] ,Interrupt 0 Enable bit 17" "Disabled,Enabled" bitfld.long 0x04 16. " [16] ,Interrupt 0 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x04 15. " [15] ,Interrupt 0 Enable bit 15" "Disabled,Enabled" bitfld.long 0x04 14. " [14] ,Interrupt 0 Enable bit 14" "Disabled,Enabled" bitfld.long 0x04 13. " [13] ,Interrupt 0 Enable bit 13" "Disabled,Enabled" bitfld.long 0x04 12. " [12] ,Interrupt 0 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x04 11. " [11] ,Interrupt 0 Enable bit 11" "Disabled,Enabled" bitfld.long 0x04 10. " [10] ,Interrupt 0 Enable bit 10" "Disabled,Enabled" bitfld.long 0x04 9. " [9] ,Interrupt 0 Enable bit 9" "Disabled,Enabled" bitfld.long 0x04 8. " [8] ,Interrupt 0 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x04 7. " [7] ,Interrupt 0 Enable bit 7" "Disabled,Enabled" bitfld.long 0x04 6. " [6] ,Interrupt 0 Enable bit 6" "Disabled,Enabled" bitfld.long 0x04 5. " [5] ,Interrupt 0 Enable bit 5" "Disabled,Enabled" bitfld.long 0x04 4. " [4] ,Interrupt 0 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x04 3. " [3] ,Interrupt 0 Enable bit 3" "Disabled,Enabled" bitfld.long 0x04 2. " [2] ,Interrupt 0 Enable bit 2" "Disabled,Enabled" bitfld.long 0x04 1. " [1] ,Interrupt 0 Enable bit 1" "Disabled,Enabled" bitfld.long 0x04 0. " [0] ,Interrupt 0 Enable bit 0" "Disabled,Enabled" line.long 0x08 "INT0ENABLE2,Interrupt Enable Register 2 for interrupts bits" bitfld.long 0x08 7. " INT0ENABLE2_[7] ,Interrupt 0 Enable bit 7" "Disabled,Enabled" bitfld.long 0x08 6. " [6] ,Interrupt 0 Enable bit 6" "Disabled,Enabled" bitfld.long 0x08 5. " [5] ,Interrupt 0 Enable bit 5" "Disabled,Enabled" bitfld.long 0x08 4. " [4] ,Interrupt 0 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x08 3. " [3] ,Interrupt 0 Enable bit 3" "Disabled,Enabled" bitfld.long 0x08 2. " [2] ,Interrupt 0 Enable bit 2" "Disabled,Enabled" bitfld.long 0x08 1. " [1] ,Interrupt 0 Enable bit 1" "Disabled,Enabled" bitfld.long 0x08 0. " [0] ,Interrupt 0 Enable bit 0" "Disabled,Enabled" textline "" line.long 0x0C "INT1ENABLE0,Interrupt Enable Register 0 for interrupts bits" bitfld.long 0x0C 31. " INT1ENABLE0_[31] ,Interrupt 1 Enable bit 31" "Disabled,Enabled" bitfld.long 0x0C 30. " [30] ,Interrupt 1 Enable bit 30" "Disabled,Enabled" bitfld.long 0x0C 29. " [29] ,Interrupt 1 Enable bit 29" "Disabled,Enabled" bitfld.long 0x0C 28. " [28] ,Interrupt 1 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x0C 27. " [27] ,Interrupt 1 Enable bit 27" "Disabled,Enabled" bitfld.long 0x0C 26. " [26] ,Interrupt 1 Enable bit 26" "Disabled,Enabled" bitfld.long 0x0C 25. " [25] ,Interrupt 1 Enable bit 25" "Disabled,Enabled" bitfld.long 0x0C 24. " [24] ,Interrupt 1 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x0C 23. " [23] ,Interrupt 1 Enable bit 23" "Disabled,Enabled" bitfld.long 0x0C 22. " [22] ,Interrupt 1 Enable bit 22" "Disabled,Enabled" bitfld.long 0x0C 21. " [21] ,Interrupt 1 Enable bit 21" "Disabled,Enabled" bitfld.long 0x0C 20. " [20] ,Interrupt 1 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x0C 19. " [19] ,Interrupt 1 Enable bit 19" "Disabled,Enabled" bitfld.long 0x0C 18. " [18] ,Interrupt 1 Enable bit 18" "Disabled,Enabled" bitfld.long 0x0C 17. " [17] ,Interrupt 1 Enable bit 17" "Disabled,Enabled" bitfld.long 0x0C 16. " [16] ,Interrupt 1 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x0C 15. " [15] ,Interrupt 1 Enable bit 15" "Disabled,Enabled" bitfld.long 0x0C 14. " [14] ,Interrupt 1 Enable bit 14" "Disabled,Enabled" bitfld.long 0x0C 13. " [13] ,Interrupt 1 Enable bit 13" "Disabled,Enabled" bitfld.long 0x0C 12. " [12] ,Interrupt 1 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x0C 11. " [11] ,Interrupt 1 Enable bit 11" "Disabled,Enabled" bitfld.long 0x0C 10. " [10] ,Interrupt 1 Enable bit 10" "Disabled,Enabled" bitfld.long 0x0C 9. " [9] ,Interrupt 1 Enable bit 9" "Disabled,Enabled" bitfld.long 0x0C 8. " [8] ,Interrupt 1 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x0C 7. " [7] ,Interrupt 1 Enable bit 7" "Disabled,Enabled" bitfld.long 0x0C 6. " [6] ,Interrupt 1 Enable bit 6" "Disabled,Enabled" bitfld.long 0x0C 5. " [5] ,Interrupt 1 Enable bit 5" "Disabled,Enabled" bitfld.long 0x0C 4. " [4] ,Interrupt 1 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x0C 3. " [3] ,Interrupt 1 Enable bit 3" "Disabled,Enabled" bitfld.long 0x0C 2. " [2] ,Interrupt 1 Enable bit 2" "Disabled,Enabled" bitfld.long 0x0C 1. " [1] ,Interrupt 1 Enable bit 1" "Disabled,Enabled" bitfld.long 0x0C 0. " [0] ,Interrupt 1 Enable bit 0" "Disabled,Enabled" line.long 0x10 "INT1ENABLE1,Interrupt Enable Register 1 for interrupts bits" bitfld.long 0x10 31. " INT1ENABLE1_[31] ,Interrupt 1 Enable bit 31" "Disabled,Enabled" bitfld.long 0x10 30. " [30] ,Interrupt 1 Enable bit 30" "Disabled,Enabled" bitfld.long 0x10 29. " [29] ,Interrupt 1 Enable bit 29" "Disabled,Enabled" bitfld.long 0x10 28. " [28] ,Interrupt 1 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x10 27. " [27] ,Interrupt 1 Enable bit 27" "Disabled,Enabled" bitfld.long 0x10 26. " [26] ,Interrupt 1 Enable bit 26" "Disabled,Enabled" bitfld.long 0x10 25. " [25] ,Interrupt 1 Enable bit 25" "Disabled,Enabled" bitfld.long 0x10 24. " [24] ,Interrupt 1 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x10 23. " [23] ,Interrupt 1 Enable bit 23" "Disabled,Enabled" bitfld.long 0x10 22. " [22] ,Interrupt 1 Enable bit 22" "Disabled,Enabled" bitfld.long 0x10 21. " [21] ,Interrupt 1 Enable bit 21" "Disabled,Enabled" bitfld.long 0x10 20. " [20] ,Interrupt 1 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x10 19. " [19] ,Interrupt 1 Enable bit 19" "Disabled,Enabled" bitfld.long 0x10 18. " [18] ,Interrupt 1 Enable bit 18" "Disabled,Enabled" bitfld.long 0x10 17. " [17] ,Interrupt 1 Enable bit 17" "Disabled,Enabled" bitfld.long 0x10 16. " [16] ,Interrupt 1 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x10 15. " [15] ,Interrupt 1 Enable bit 15" "Disabled,Enabled" bitfld.long 0x10 14. " [14] ,Interrupt 1 Enable bit 14" "Disabled,Enabled" bitfld.long 0x10 13. " [13] ,Interrupt 1 Enable bit 13" "Disabled,Enabled" bitfld.long 0x10 12. " [12] ,Interrupt 1 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x10 11. " [11] ,Interrupt 1 Enable bit 11" "Disabled,Enabled" bitfld.long 0x10 10. " [10] ,Interrupt 1 Enable bit 10" "Disabled,Enabled" bitfld.long 0x10 9. " [9] ,Interrupt 1 Enable bit 9" "Disabled,Enabled" bitfld.long 0x10 8. " [8] ,Interrupt 1 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x10 7. " [7] ,Interrupt 1 Enable bit 7" "Disabled,Enabled" bitfld.long 0x10 6. " [6] ,Interrupt 1 Enable bit 6" "Disabled,Enabled" bitfld.long 0x10 5. " [5] ,Interrupt 1 Enable bit 5" "Disabled,Enabled" bitfld.long 0x10 4. " [4] ,Interrupt 1 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x10 3. " [3] ,Interrupt 1 Enable bit 3" "Disabled,Enabled" bitfld.long 0x10 2. " [2] ,Interrupt 1 Enable bit 2" "Disabled,Enabled" bitfld.long 0x10 1. " [1] ,Interrupt 1 Enable bit 1" "Disabled,Enabled" bitfld.long 0x10 0. " [0] ,Interrupt 1 Enable bit 0" "Disabled,Enabled" line.long 0x14 "INT1ENABLE2,Interrupt Enable Register 2 for interrupts bits" bitfld.long 0x14 7. " INT1ENABLE2_[7] ,Interrupt 1 Enable bit 7" "Disabled,Enabled" bitfld.long 0x14 6. " [6] ,Interrupt 1 Enable bit 6" "Disabled,Enabled" bitfld.long 0x14 5. " [5] ,Interrupt 1 Enable bit 5" "Disabled,Enabled" bitfld.long 0x14 4. " [4] ,Interrupt 1 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x14 3. " [3] ,Interrupt 1 Enable bit 3" "Disabled,Enabled" bitfld.long 0x14 2. " [2] ,Interrupt 1 Enable bit 2" "Disabled,Enabled" bitfld.long 0x14 1. " [1] ,Interrupt 1 Enable bit 1" "Disabled,Enabled" bitfld.long 0x14 0. " [0] ,Interrupt 1 Enable bit 0" "Disabled,Enabled" textline "" line.long 0x18 "INTCLEAR0,Interrupt Clear Register 0 for interrupt bits" eventfld.long 0x18 31. " INTCLEAR0_[31] ,Interrupt Clear bit 31" "Not clear,Clear" eventfld.long 0x18 30. " [30] ,Interrupt Clear bit 30" "Not clear,Clear" eventfld.long 0x18 29. " [29] ,Interrupt Clear bit 29" "Not clear,Clear" eventfld.long 0x18 28. " [28] ,Interrupt Clear bit 28" "Not clear,Clear" textline " " eventfld.long 0x18 27. " [27] ,Interrupt Clear bit 27" "Not clear,Clear" eventfld.long 0x18 26. " [26] ,Interrupt Clear bit 26" "Not clear,Clear" eventfld.long 0x18 25. " [25] ,Interrupt Clear bit 25" "Not clear,Clear" eventfld.long 0x18 24. " [24] ,Interrupt Clear bit 24" "Not clear,Clear" textline " " eventfld.long 0x18 23. " [23] ,Interrupt Clear bit 23" "Not clear,Clear" eventfld.long 0x18 22. " [22] ,Interrupt Clear bit 22" "Not clear,Clear" eventfld.long 0x18 21. " [21] ,Interrupt Clear bit 21" "Not clear,Clear" eventfld.long 0x18 20. " [20] ,Interrupt Clear bit 20" "Not clear,Clear" textline " " eventfld.long 0x18 19. " [19] ,Interrupt Clear bit 19" "Not clear,Clear" eventfld.long 0x18 18. " [18] ,Interrupt Clear bit 18" "Not clear,Clear" eventfld.long 0x18 17. " [17] ,Interrupt Clear bit 17" "Not clear,Clear" eventfld.long 0x18 16. " [16] ,Interrupt Clear bit 16" "Not clear,Clear" textline " " eventfld.long 0x18 15. " [15] ,Interrupt Clear bit 15" "Not clear,Clear" eventfld.long 0x18 14. " [14] ,Interrupt Clear bit 14" "Not clear,Clear" eventfld.long 0x18 13. " [13] ,Interrupt Clear bit 13" "Not clear,Clear" eventfld.long 0x18 12. " [12] ,Interrupt Clear bit 12" "Not clear,Clear" textline " " eventfld.long 0x18 11. " [11] ,Interrupt Clear bit 11" "Not clear,Clear" eventfld.long 0x18 10. " [10] ,Interrupt Clear bit 10" "Not clear,Clear" eventfld.long 0x18 9. " [9] ,Interrupt Clear bit 9" "Not clear,Clear" eventfld.long 0x18 8. " [8] ,Interrupt Clear bit 8" "Not clear,Clear" textline " " eventfld.long 0x18 7. " [7] ,Interrupt Clear bit 7" "Not clear,Clear" eventfld.long 0x18 6. " [6] ,Interrupt Clear bit 6" "Not clear,Clear" eventfld.long 0x18 5. " [5] ,Interrupt Clear bit 5" "Not clear,Clear" eventfld.long 0x18 4. " [4] ,Interrupt Clear bit 4" "Not clear,Clear" textline " " eventfld.long 0x18 3. " [3] ,Interrupt Clear bit 3" "Not clear,Clear" eventfld.long 0x18 2. " [2] ,Interrupt Clear bit 2" "Not clear,Clear" eventfld.long 0x18 1. " [1] ,Interrupt Clear bit 1" "Not clear,Clear" eventfld.long 0x18 0. " [0] ,Interrupt Clear bit 0" "Not clear,Clear" line.long 0x1C "INTCLEAR1,Interrupt Clear Register 1 for interrupt bits" eventfld.long 0x1C 31. " INTCLEAR1_[31] ,Interrupt Clear bit 31" "Not clear,Clear" eventfld.long 0x1C 30. " [30] ,Interrupt Clear bit 30" "Not clear,Clear" eventfld.long 0x1C 29. " [29] ,Interrupt Clear bit 29" "Not clear,Clear" eventfld.long 0x1C 28. " [28] ,Interrupt Clear bit 28" "Not clear,Clear" textline " " eventfld.long 0x1C 27. " [27] ,Interrupt Clear bit 27" "Not clear,Clear" eventfld.long 0x1C 26. " [26] ,Interrupt Clear bit 26" "Not clear,Clear" eventfld.long 0x1C 25. " [25] ,Interrupt Clear bit 25" "Not clear,Clear" eventfld.long 0x1C 24. " [24] ,Interrupt Clear bit 24" "Not clear,Clear" textline " " eventfld.long 0x1C 23. " [23] ,Interrupt Clear bit 23" "Not clear,Clear" eventfld.long 0x1C 22. " [22] ,Interrupt Clear bit 22" "Not clear,Clear" eventfld.long 0x1C 21. " [21] ,Interrupt Clear bit 21" "Not clear,Clear" eventfld.long 0x1C 20. " [20] ,Interrupt Clear bit 20" "Not clear,Clear" textline " " eventfld.long 0x1C 19. " [19] ,Interrupt Clear bit 19" "Not clear,Clear" eventfld.long 0x1C 18. " [18] ,Interrupt Clear bit 18" "Not clear,Clear" eventfld.long 0x1C 17. " [17] ,Interrupt Clear bit 17" "Not clear,Clear" eventfld.long 0x1C 16. " [16] ,Interrupt Clear bit 16" "Not clear,Clear" textline " " eventfld.long 0x1C 15. " [15] ,Interrupt Clear bit 15" "Not clear,Clear" eventfld.long 0x1C 14. " [14] ,Interrupt Clear bit 14" "Not clear,Clear" eventfld.long 0x1C 13. " [13] ,Interrupt Clear bit 13" "Not clear,Clear" eventfld.long 0x1C 12. " [12] ,Interrupt Clear bit 12" "Not clear,Clear" textline " " eventfld.long 0x1C 11. " [11] ,Interrupt Clear bit 11" "Not clear,Clear" eventfld.long 0x1C 10. " [10] ,Interrupt Clear bit 10" "Not clear,Clear" eventfld.long 0x1C 9. " [9] ,Interrupt Clear bit 9" "Not clear,Clear" eventfld.long 0x1C 8. " [8] ,Interrupt Clear bit 8" "Not clear,Clear" textline " " eventfld.long 0x1C 7. " [7] ,Interrupt Clear bit 7" "Not clear,Clear" eventfld.long 0x1C 6. " [6] ,Interrupt Clear bit 6" "Not clear,Clear" eventfld.long 0x1C 5. " [5] ,Interrupt Clear bit 5" "Not clear,Clear" eventfld.long 0x1C 4. " [4] ,Interrupt Clear bit 4" "Not clear,Clear" textline " " eventfld.long 0x1C 3. " [3] ,Interrupt Clear bit 3" "Not clear,Clear" eventfld.long 0x1C 2. " [2] ,Interrupt Clear bit 2" "Not clear,Clear" eventfld.long 0x1C 1. " [1] ,Interrupt Clear bit 1" "Not clear,Clear" eventfld.long 0x1C 0. " [0] ,Interrupt Clear bit 0" "Not clear,Clear" line.long 0x20 "INTCLEAR2,Interrupt Clear Register 2 for interrupt bits" eventfld.long 0x20 7. " INTCLEAR2_[7] ,Interrupt Clear bit 7" "Not clear,Clear" eventfld.long 0x20 6. " [6] ,Interrupt Clear bit 6" "Not clear,Clear" eventfld.long 0x20 5. " [5] ,Interrupt Clear bit 5" "Not clear,Clear" eventfld.long 0x20 4. " [4] ,Interrupt Clear bit 4" "Not clear,Clear" textline " " eventfld.long 0x20 3. " [3] ,Interrupt Clear bit 3" "Not clear,Clear" eventfld.long 0x20 2. " [2] ,Interrupt Clear bit 2" "Not clear,Clear" eventfld.long 0x20 1. " [1] ,Interrupt Clear bit 1" "Not clear,Clear" eventfld.long 0x20 0. " [0] ,Interrupt Clear bit 0" "Not clear,Clear" textline "" line.long 0x24 "INTPRESET0,Interrupt Preset Register 1 for interrupt bits" eventfld.long 0x24 31. " INTPRESET0_[31] ,Interrupt Preset bit 31" "Not interrupt,Interrupt" eventfld.long 0x24 30. " [30] ,Interrupt Preset bit 30" "Not interrupt,Interrupt" eventfld.long 0x24 29. " [29] ,Interrupt Preset bit 29" "Not interrupt,Interrupt" eventfld.long 0x24 28. " [28] ,Interrupt Preset bit 28" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 27. " [27] ,Interrupt Preset bit 27" "Not interrupt,Interrupt" eventfld.long 0x24 26. " [26] ,Interrupt Preset bit 26" "Not interrupt,Interrupt" eventfld.long 0x24 25. " [25] ,Interrupt Preset bit 25" "Not interrupt,Interrupt" eventfld.long 0x24 24. " [24] ,Interrupt Preset bit 24" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 23. " [23] ,Interrupt Preset bit 23" "Not interrupt,Interrupt" eventfld.long 0x24 22. " [22] ,Interrupt Preset bit 22" "Not interrupt,Interrupt" eventfld.long 0x24 21. " [21] ,Interrupt Preset bit 21" "Not interrupt,Interrupt" eventfld.long 0x24 20. " [20] ,Interrupt Preset bit 20" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 19. " [19] ,Interrupt Preset bit 19" "Not interrupt,Interrupt" eventfld.long 0x24 18. " [18] ,Interrupt Preset bit 18" "Not interrupt,Interrupt" eventfld.long 0x24 17. " [17] ,Interrupt Preset bit 17" "Not interrupt,Interrupt" eventfld.long 0x24 16. " [16] ,Interrupt Preset bit 16" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 15. " [15] ,Interrupt Preset bit 15" "Not interrupt,Interrupt" eventfld.long 0x24 14. " [14] ,Interrupt Preset bit 14" "Not interrupt,Interrupt" eventfld.long 0x24 13. " [13] ,Interrupt Preset bit 13" "Not interrupt,Interrupt" eventfld.long 0x24 12. " [12] ,Interrupt Preset bit 12" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 11. " [11] ,Interrupt Preset bit 11" "Not interrupt,Interrupt" eventfld.long 0x24 10. " [10] ,Interrupt Preset bit 10" "Not interrupt,Interrupt" eventfld.long 0x24 9. " [9] ,Interrupt Preset bit 9" "Not interrupt,Interrupt" eventfld.long 0x24 8. " [8] ,Interrupt Preset bit 8" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 7. " [7] ,Interrupt Preset bit 7" "Not interrupt,Interrupt" eventfld.long 0x24 6. " [6] ,Interrupt Preset bit 6" "Not interrupt,Interrupt" eventfld.long 0x24 5. " [5] ,Interrupt Preset bit 5" "Not interrupt,Interrupt" eventfld.long 0x24 4. " [4] ,Interrupt Preset bit 4" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 3. " [3] ,Interrupt Preset bit 3" "Not interrupt,Interrupt" eventfld.long 0x24 2. " [2] ,Interrupt Preset bit 2" "Not interrupt,Interrupt" eventfld.long 0x24 1. " [1] ,Interrupt Preset bit 1" "Not interrupt,Interrupt" eventfld.long 0x24 0. " [0] ,Interrupt Preset bit 0" "Not interrupt,Interrupt" line.long 0x28 "INTPRESET1,Interrupt Preset Register 1 for interrupt bits" eventfld.long 0x28 31. " INTPRESET1_[31] ,Interrupt Preset bit 31" "Not interrupt,Interrupt" eventfld.long 0x28 30. " [30] ,Interrupt Preset bit 30" "Not interrupt,Interrupt" eventfld.long 0x28 29. " [29] ,Interrupt Preset bit 29" "Not interrupt,Interrupt" eventfld.long 0x28 28. " [28] ,Interrupt Preset bit 28" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 27. " [27] ,Interrupt Preset bit 27" "Not interrupt,Interrupt" eventfld.long 0x28 26. " [26] ,Interrupt Preset bit 26" "Not interrupt,Interrupt" eventfld.long 0x28 25. " [25] ,Interrupt Preset bit 25" "Not interrupt,Interrupt" eventfld.long 0x28 24. " [24] ,Interrupt Preset bit 24" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 23. " [23] ,Interrupt Preset bit 23" "Not interrupt,Interrupt" eventfld.long 0x28 22. " [22] ,Interrupt Preset bit 22" "Not interrupt,Interrupt" eventfld.long 0x28 21. " [21] ,Interrupt Preset bit 21" "Not interrupt,Interrupt" eventfld.long 0x28 20. " [20] ,Interrupt Preset bit 20" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 19. " [19] ,Interrupt Preset bit 19" "Not interrupt,Interrupt" eventfld.long 0x28 18. " [18] ,Interrupt Preset bit 18" "Not interrupt,Interrupt" eventfld.long 0x28 17. " [17] ,Interrupt Preset bit 17" "Not interrupt,Interrupt" eventfld.long 0x28 16. " [16] ,Interrupt Preset bit 16" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 15. " [15] ,Interrupt Preset bit 15" "Not interrupt,Interrupt" eventfld.long 0x28 14. " [14] ,Interrupt Preset bit 14" "Not interrupt,Interrupt" eventfld.long 0x28 13. " [13] ,Interrupt Preset bit 13" "Not interrupt,Interrupt" eventfld.long 0x28 12. " [12] ,Interrupt Preset bit 12" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 11. " [11] ,Interrupt Preset bit 11" "Not interrupt,Interrupt" eventfld.long 0x28 10. " [10] ,Interrupt Preset bit 10" "Not interrupt,Interrupt" eventfld.long 0x28 9. " [9] ,Interrupt Preset bit 9" "Not interrupt,Interrupt" eventfld.long 0x28 8. " [8] ,Interrupt Preset bit 8" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 7. " [7] ,Interrupt Preset bit 7" "Not interrupt,Interrupt" eventfld.long 0x28 6. " [6] ,Interrupt Preset bit 6" "Not interrupt,Interrupt" eventfld.long 0x28 5. " [5] ,Interrupt Preset bit 5" "Not interrupt,Interrupt" eventfld.long 0x28 4. " [4] ,Interrupt Preset bit 4" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 3. " [3] ,Interrupt Preset bit 3" "Not interrupt,Interrupt" eventfld.long 0x28 2. " [2] ,Interrupt Preset bit 2" "Not interrupt,Interrupt" eventfld.long 0x28 1. " [1] ,Interrupt Preset bit 1" "Not interrupt,Interrupt" eventfld.long 0x28 0. " [0] ,Interrupt Preset bit 0" "Not interrupt,Interrupt" line.long 0x2C "INTPRESET2,Interrupt Preset Register 2 for interrupt bits" eventfld.long 0x2C 7. " INTPRESET2_[7] ,Interrupt Preset bit 7" "Not interrupt,Interrupt" eventfld.long 0x2C 6. " [6] ,Interrupt Preset bit 6" "Not interrupt,Interrupt" eventfld.long 0x2C 5. " [5] ,Interrupt Preset bit 5" "Not interrupt,Interrupt" eventfld.long 0x2C 4. " [4] ,Interrupt Preset bit 4" "Not interrupt,Interrupt" textline " " eventfld.long 0x2C 3. " [3] ,Interrupt Preset bit 3" "Not interrupt,Interrupt" eventfld.long 0x2C 2. " [2] ,Interrupt Preset bit 2" "Not interrupt,Interrupt" eventfld.long 0x2C 1. " [1] ,Interrupt Preset bit 1" "Not interrupt,Interrupt" eventfld.long 0x2C 0. " [0] ,Interrupt Preset bit 0" "Not interrupt,Interrupt" tree.end width 15. group.long 0x400++0x03 line.long 0x00 "FIFO,FIFO" button "FIFO" "d (ad:0x3A010000+0x400)--(ad:0x3A010000+0x4FF) /long" group.long 0x500++0x03 line.long 0x00 "CONTROL,Message Buffer Control" bitfld.long 0x00 31. " BLOCK_ON_FATAL ,Suppress pending signal when fatal error was detected" "No error,Error" bitfld.long 0x00 2. " R1BUF_BACKPRESSURE_ENABLE ,Enable backpressure when read buffer 1 is running full" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " R0BUF_BACKPRESSURE_ENABLE ,Enable backpressure when read buffer 0 is running full" "Disabled,Enabled" rgroup.long 0x504++0x03 line.long 0x00 "STATUS,Message Buffer Status" bitfld.long 0x00 6. " WDG_TIMEOUT ,Watchdog timeout" "Not timeout,Timeout" bitfld.long 0x00 5. " WRBUF_EMPTY ,Write buffer is empty" "Not empty,Empty" textline " " bitfld.long 0x00 4. " WRBUF_FULL ,Write buffer is full" "Not full,Full" bitfld.long 0x00 3. " R1BUF_EMPTY ,Read buffer 1 is empty" "Not empty,Empty" textline " " bitfld.long 0x00 2. " R1BUF_FULL ,Read buffer 1 is full" "Not full,Full" bitfld.long 0x00 1. " R0BUF_EMPTY ,Read buffer 0 is empty" "Not empty,Empty" textline " " bitfld.long 0x00 0. " R0BUF_FULL ,Read buffer 0 is full" "Not full,Full" group.long 0x508++0x0B line.long 0x00 "CLEAR,Message Buffer Clear" eventfld.long 0x00 2. " R1BUF_CLEAR ,Writing a '1' clears read buffer 1" "Not clear,Clear" eventfld.long 0x00 1. " R0BUF_CLEAR ,Writing a '1' clears read buffer 0" "Not clear,Clear" textline " " eventfld.long 0x00 0. " WRBUF_CLEAR ,Writing a '1' clears write buffer" "Not clear,Clear" line.long 0x04 "DMA_CONTROL,DMA Control" bitfld.long 0x04 24.--25. " DMA2_MODE ,Dma2 mode" "Previous,Local,Both," bitfld.long 0x04 20.--21. " DMA1_MODE ,Dma1 mode" "Previous,Local,Both," textline " " bitfld.long 0x04 16.--17. " DMA0_MODE ,Dma0 mode" "Previous,Local,Both," bitfld.long 0x04 10. " R1BUF_DMA_ENABLE ,Enable DMA for read buffer 1" "Disabled,Enabled" textline " " bitfld.long 0x04 6. " R0BUF_DMA_ENABLE ,Enable DMA for read buffer 0" "Disabled,Enabled" bitfld.long 0x04 4.--5. " R0BUF_DMA_PORT ,DMA port number for read buffer 0" "0,1,2,3" textline " " bitfld.long 0x04 2. " WRBUF_DMA_ENABLE ,Enable DMA for write buffer" "Disabled,Enabled" bitfld.long 0x04 0.--1. " WRBUF_DMA_PORT ,DMA port number for write buffer" "0,1,2,3" line.long 0x08 "WATCHDOG_LOAD,Watchdog counter preset value" textline "" width 39. group.long 0x600++0x0B line.long 0x00 "RX0_I2C_OUTBOUND_JOB_SPEC_STATUS,RX0_I2C_Outbound_Job_Spec_Status" eventfld.long 0x00 31. " RX0_I2C_OUTBOUND_JOB_SPEC_CLEAR ,RX0_I2C_Outbound_Job_Spec_Clear" "Not clear,Clear" textline " " rbitfld.long 0x00 0. " RX0_I2C_OUTBOUND_JOB_SPEC_BUSY ,RX0_I2C_Outbound_Job_Spec_Busy" "Not busy,Busy" line.long 0x04 "RX0_I2C_OUTBOUND_JOB_SPEC_DATA_LOW,RX0_I2C_Outbound_Job_Spec_Data_Low" line.long 0x08 "RX0_I2C_OUTBOUND_JOB_SPEC_DATA_HIGH,RX0_I2C_Outbound_Job_Spec_Data_High" rgroup.long 0x60C++0x0B line.long 0x00 "RX0_I2C_INBOUND_JOB_SPEC_STATUS,RX0_I2C_Inbound_Job_Spec_Status" bitfld.long 0x00 0. " RX0_I2C_INBOUND_JOB_SPEC_VALID ,RX0_I2C_Inbound_Job_Spec_Valid" "No,Yes" line.long 0x04 "RX0_I2C_INBOUND_JOB_SPEC_DATA_LOW,RX0_I2C_Inbound_Job_Spec_Data_Low" line.long 0x08 "RX0_I2C_INBOUND_JOB_SPEC_DATA_HIGH,RX0_I2C_Inbound_Job_Spec_Data_High" group.long 0x618++0x0B line.long 0x00 "RX0_I2C_INBOUND_JOB_SPEC_ERROR,RX0_I2C_Inbound_Job_Spec_Error" bitfld.long 0x00 31. " RX0_I2C_INBOUND_JOB_SPEC_ERROR ,RX0_I2C_Inbound_Job_Spec_Error" "No error,Error" line.long 0x04 "RX0_I2C_OUTBOUND_STATUS,RX0_I2C_Outbound_Status" eventfld.long 0x04 31. " RX0_I2C_OUTBOUND_STATUS_CLEAR ,RX0_I2C_Outbound_Status_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX0_I2C_OUTBOUND_STATUS_BUSY ,RX0_I2C_Outbound_Status_Busy" "Not busy,Busy" line.long 0x08 "RX0_I2C_OUTBOUND_STATUS_DATA,RX0_I2C_Outbound_Status_Data" bitfld.long 0x08 3. " RX0_I2C_OUTBOUND_STATUS_ALOST_DETECTED ,RX0_I2C_Outbound_Status_Alost_Detected" "Not detected,Detected" textline " " bitfld.long 0x08 2. " RX0_I2C_OUTBOUND_STATUS_NACK_DETECTED ,RX0_I2C_Outbound_Status_Nack_Detected" "Not detected,Detected" textline " " bitfld.long 0x08 1. " RX0_I2C_OUTBOUND_STATUS_JOB_CACC ,RX0_I2C_Outbound_Status_Job_Cacc" "0,1" textline " " bitfld.long 0x08 0. " RX0_I2C_OUTBOUND_STATUS_JOB_DONE ,RX0_I2C_Outbound_Status_Job_Done" "0,1" rgroup.long 0x624++0x03 line.long 0x00 "RX0_I2C_INBOUND_STATUS,RX0_I2C_Inbound_Status" bitfld.long 0x00 0. " RX0_I2C_INBOUND_STATUS_VALID ,RX0_I2C_Inbound_Status_Valid" "No,Yes" group.long 0x628++0x0B line.long 0x00 "RX0_I2C_INBOUND_STATUS_DATA,RX0_I2C_Inbound_Status_Data" bitfld.long 0x00 31. " RX0_I2C_INBOUND_STATUS_ERROR ,RX0_I2C_Inbound_Status_Error" "No error,Error" textline " " rbitfld.long 0x00 3. " RX0_I2C_INBOUND_STATUS_ALOST_DETECTED ,RX0_I2C_Inbound_Status_Alost_detected" "Not detected,Detected" textline " " rbitfld.long 0x00 2. " RX0_I2C_INBOUND_STATUS_NACK_DETECTED ,RX0_I2C_Inbound_Status_Nack_detected" "Not detected,Detected" textline " " rbitfld.long 0x00 1. " RX0_I2C_INBOUND_STATUS_JOB_CACC ,RX0_I2C_Inbound_Status_Job_cacc" "0,1" textline " " rbitfld.long 0x00 0. " RX0_I2C_INBOUND_STATUS_JOB_DONE ,RX0_I2C_Inbound_Status_Job_done" "0,1" line.long 0x04 "RX0_I2C_OUTBOUND_READ_RESPONSE_STATUS,RX0_I2C_Outbound_Read_Response_Status" eventfld.long 0x04 31. " RX0_I2C_OUTBOUND_READ_RESPONSE_CLEAR ,RX0_I2C_Outbound_Read_Response_Clear" "Not clear,Clear" textline " " bitfld.long 0x04 0. " RX0_I2C_OUTBOUND_READ_RESPONSE_BUSY ,RX0_I2C_Outbound_Read_Response_Busy" "Not busy,Busy" line.long 0x08 "RX0_I2C_OUTBOUND_READ_RESPONSE_DATA,RX0_I2C_Outbound_Read_Response_Data" hexmask.long.byte 0x08 0.--7. 1. " RX0_I2C_OUTBOUND_READ_RESPONSE_DATA ,RX0_I2C_Outbound_Read_Response_Data" rgroup.long 0x634++0x03 line.long 0x00 "RX0_I2C_INBOUND_READ_RESPONSE_STATUS,RX0_I2C_Inbound_Read_Response_Status" bitfld.long 0x00 0. " RX0_I2C_INBOUND_READ_RESPONSE_VALID ,RX0_I2C_Inbound_Read_Response_Valid" "No,Yes" group.long 0x638++0x0F line.long 0x00 "RX0_I2C_INBOUND_READ_RESPONSE_DATA,RX0_I2C_Inbound_Read_Response_Data" bitfld.long 0x00 31. " RX0_I2C_INBOUND_READ_RESPONSE_ERROR ,RX0_I2C_Inbound_Read_Response_Error" "No error,Error" textline " " rbitfld.long 0x00 8.--10. " RX0_I2C_INBOUND_READ_RESPONSE_DATA_NUM ,RX0_I2C_Inbound_Read_Response_Data_Num" "0,1,2,3,4,5,6,7" textline " " hexmask.long.byte 0x00 0.--7. 1. " RX0_I2C_INBOUND_READ_RESPONSE_DATA ,RX0_I2C_Inbound_Read_Response_Data" line.long 0x04 "RX1_I2C_OUTBOUND_JOB_SPEC_STATUS,RX1_I2C_Outbound_Job_Spec_Status" eventfld.long 0x04 31. " RX1_I2C_OUTBOUND_JOB_SPEC_CLEAR ,RX1_I2C_Outbound_Job_Spec_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX1_I2C_OUTBOUND_JOB_SPEC_BUSY ,RX1_I2C_Outbound_Job_Spec_Busy" "Not busy,Busy" line.long 0x08 "RX1_I2C_OUTBOUND_JOB_SPEC_DATA_LOW,RX1_I2C_Outbound_Job_Spec_Data_Low" line.long 0x0C "RX1_I2C_OUTBOUND_JOB_SPEC_DATA_HIGH,RX1_I2C_Outbound_Job_Spec_Data_High" rgroup.long 0x648++0x0B line.long 0x00 "RX1_I2C_INBOUND_JOB_SPEC_STATUS,RX1_I2C_Inbound_Job_Spec_Status" bitfld.long 0x00 0. " RX1_I2C_INBOUND_JOB_SPEC_VALID ,RX1_I2C_Inbound_Job_Spec_Valid" "No,Yes" line.long 0x04 "RX1_I2C_INBOUND_JOB_SPEC_DATA_LOW,RX1_I2C_Inbound_Job_Spec_Data_Low" line.long 0x08 "RX1_I2C_INBOUND_JOB_SPEC_DATA_HIGH,RX1_I2C_Inbound_Job_Spec_Data_High" group.long 0x654++0x0B line.long 0x00 "RX1_I2C_INBOUND_JOB_SPEC_ERROR,RX1_I2C_Inbound_Job_Spec_Error" bitfld.long 0x00 31. " RX1_I2C_INBOUND_JOB_SPEC_ERROR ,RX1_I2C_Inbound_Job_Spec_Error" "No error,Error" line.long 0x04 "RX1_I2C_OUTBOUND_STATUS,RX1_I2C_Outbound_Status" eventfld.long 0x04 31. " RX1_I2C_OUTBOUND_STATUS_CLEAR ,RX1_I2C_Outbound_Status_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX1_I2C_OUTBOUND_STATUS_BUSY ,RX1_I2C_Outbound_Status_Busy" "Not busy,Busy" line.long 0x08 "RX1_I2C_OUTBOUND_STATUS_DATA,RX1_I2C_Outbound_Status_Data" bitfld.long 0x08 3. " RX1_I2C_OUTBOUND_STATUS_ALOST_DETECTED ,RX1_I2C_Outbound_Status_Alost_Detected" "Not detected,Detected" textline " " bitfld.long 0x08 2. " RX1_I2C_OUTBOUND_STATUS_NACK_DETECTED ,RX1_I2C_Outbound_Status_Nack_Detected" "Not detected,Detected" textline " " bitfld.long 0x08 1. " RX1_I2C_OUTBOUND_STATUS_JOB_CACC ,RX1_I2C_Outbound_Status_Job_Cacc" "0,1" textline " " bitfld.long 0x08 0. " RX1_I2C_OUTBOUND_STATUS_JOB_DONE ,RX1_I2C_Outbound_Status_Job_Done" "0,1" rgroup.long 0x660++0x03 line.long 0x00 "RX1_I2C_INBOUND_STATUS,RX1_I2C_Inbound_Status" bitfld.long 0x00 0. " RX1_I2C_INBOUND_STATUS_VALID ,RX1_I2C_Inbound_Status_Valid" "No,Yes" group.long 0x664++0x0B line.long 0x00 "RX1_I2C_INBOUND_STATUS_DATA,RX1_I2C_Inbound_Status_Data" bitfld.long 0x00 31. " RX1_I2C_INBOUND_STATUS_ERROR ,RX1_I2C_Inbound_Status_Error" "No error,Error" textline " " rbitfld.long 0x00 3. " RX1_I2C_INBOUND_STATUS_ALOST_DETECTED ,RX1_I2C_Inbound_Status_Alost_detected" "Not detected,Detected" textline " " bitfld.long 0x00 2. " RX1_I2C_INBOUND_STATUS_NACK_DETECTED ,RX1_I2C_Inbound_Status_Nack_detected" "Not detected,Detected" textline " " rbitfld.long 0x00 1. " RX1_I2C_INBOUND_STATUS_JOB_CACC ,RX1_I2C_Inbound_Status_Job_cacc" "0,1" textline " " bitfld.long 0x00 0. " RX1_I2C_INBOUND_STATUS_JOB_DONE ,RX1_I2C_Inbound_Status_Job_done" "0,1" line.long 0x04 "RX1_I2C_OUTBOUND_READ_RESPONSE_STATUS,RX1_I2C_Outbound_Read_Response_Status" eventfld.long 0x04 31. " RX1_I2C_OUTBOUND_READ_RESPONSE_CLEAR ,RX1_I2C_Outbound_Read_Response_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX1_I2C_OUTBOUND_READ_RESPONSE_BUSY ,RX1_I2C_Outbound_Read_Response_Busy" "Not busy,Busy" line.long 0x08 "RX1_I2C_OUTBOUND_READ_RESPONSE_DATA,RX1_I2C_Outbound_Read_Response_Data" hexmask.long.byte 0x08 0.--7. 1. " RX1_I2C_OUTBOUND_READ_RESPONSE_DATA ,RX1_I2C_Outbound_Read_Response_Data" rgroup.long 0x670++0x03 line.long 0x00 "RX1_I2C_INBOUND_READ_RESPONSE_STATUS,RX1_I2C_Inbound_Read_Response_Status" bitfld.long 0x00 0. " RX1_I2C_INBOUND_READ_RESPONSE_VALID ,RX1_I2C_Inbound_Read_Response_Valid" "No,Yes" group.long 0x674++0x0B line.long 0x00 "RX1_I2C_INBOUND_READ_RESPONSE_DATA,RX1_I2C_Inbound_Read_Response_Data" bitfld.long 0x00 31. " RX1_I2C_INBOUND_READ_RESPONSE_ERROR ,RX1_I2C_Inbound_Read_Response_Error" "No error,Error" textline " " rbitfld.long 0x00 8.--10. " RX1_I2C_INBOUND_READ_RESPONSE_DATA_NUM ,RX1_I2C_Inbound_Read_Response_Data_Num" "0,1,2,3,4,5,6,7" textline " " hexmask.long.byte 0x00 0.--7. 1. " RX1_I2C_INBOUND_READ_RESPONSE_DATA ,RX1_I2C_Inbound_Read_Response_Data" line.long 0x04 "RX0_REMOTE_CONTROLLER_OUTBOUND_STATUS,RX0_Remote_Controller_Outbound_Status" eventfld.long 0x04 31. " RX0_REMOTE_CONTROLLER_OUTBOUND_CLEAR ,RX0_Remote_Controller_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX0_REMOTE_CONTROLLER_OUTBOUND_BUSY ,RX0_Remote_Controller_Outbound_Busy" "Not busy,Busy" line.long 0x08 "RX0_REMOTE_CONTROLLER_OUTBOUND_DATA,RX0_Remote_Controller_Outbound_Data" hexmask.long.byte 0x08 8.--15. 1. " RX0_REMOTE_CONTROLLER_OUTBOUND_DATA ,RX0_Remote_Controller_Outbound_Data" textline " " bitfld.long 0x08 7. " RX0_REMOTE_CONTROLLER_OUTBOUND_RW ,RX0_Remote_Controller_Outbound_RW" "0,1" textline " " hexmask.long.byte 0x08 0.--6. 1. " RX0_REMOTE_CONTROLLER_OUTBOUND_ADDRESS ,RX0_Remote_Controller_Outbound_Address" rgroup.long 0x680++0x03 line.long 0x00 "RX0_REMOTE_CONTROLLER_INBOUND_STATUS,RX0_Remote_Controller_Inbound_Status" bitfld.long 0x00 0. " RX0_REMOTE_CONTROLLER_INBOUND_VALID ,RX0_Remote_Controller_Inbound_Valid" "No,Yes" group.long 0x684++0x03 line.long 0x00 "RX0_REMOTE_CONTROLLER_INBOUND_DATA,RX0_Remote_Controller_Inbound_Data" rbitfld.long 0x00 31. " RX0_REMOTE_CONTROLLER_INBOUND_ERROR ,RX0_Remote_Controller_Inbound_Error" "No error,Error" textline " " hexmask.long.byte 0x00 0.--7. 1. " RX0_REMOTE_CONTROLLER_INBOUND_RESPONSE_DATA ,RX0_Remote_Controller_Inbound_Response_Data" rgroup.long 0x688++0x03 line.long 0x00 "RX0_REMOTE_SERVICE_INBOUND_STATUS,RX0_Remote_Service_Inbound_Status" bitfld.long 0x00 0. " RX0_REMOTE_SERVICE_INBOUND_VALID ,RX0_Remote_Service_Inbound_Valid" "No,Yes" group.long 0x68C++0x1B line.long 0x00 "RX0_REMOTE_SERVICE_INBOUND_DATA,RX0_Remote_Service_Inbound_Data" bitfld.long 0x00 31. " RX0_REMOTE_SERVICE_INBOUND_ERROR ,RX0_Remote_Service_Inbound_Error" "No error,Error" textline " " hexmask.long.byte 0x00 8.--15. 1. " RX0_REMOTE_SERVICE_INBOUND_DATA ,RX0_Remote_Service_Inbound_Data" textline " " bitfld.long 0x00 7. " RX0_REMOTE_SERVICE_INBOUND_RW ,RX0_Remote_Service_Inbound_RW" "0,1" textline " " hexmask.long.byte 0x00 0.--6. 1. " RX0_REMOTE_SERVICE_INBOUND_ADDRESS ,RX0_Remote_Service_Inbound_Address" line.long 0x04 "RX0_REMOTE_SERVICE_OUTBOUND_STATUS,RX0_Remote_Service_Outbound_Status" eventfld.long 0x04 31. " RX0_REMOTE_SERVICE_OUTBOUND_CLEAR ,RX0_Remote_Service_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX0_REMOTE_SERVICE_OUTBOUND_BUSY ,RX0_Remote_Service_Outbound_Busy" "Not busy,Busy" line.long 0x08 "RX0_REMOTE_SERVICE_OUTBOUND_DATA,RX0_Remote_Service_Outbound_Data" hexmask.long.byte 0x08 0.--7. 1. " RX0_REMOTE_SERVICE_OUTBOUND_READ_RESPONSE_DATA ,RX0_Remote_Service_Outbound_Read_Response_Data" line.long 0x0C "RX0_REMOTE_COMMAND_OUTBOUND_STATUS,RX0_Remote_Command_Outbound_Status" eventfld.long 0x0C 31. " RX0_REMOTE_COMMAND_OUTBOUND_CLEAR ,RX0_Remote_Command_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x0C 0. " RX0_REMOTE_COMMAND_OUTBOUND_BUSY ,RX0_Remote_Command_Outbound_Busy" "Not busy,Busy" line.long 0x10 "RX0_REMOTE_COMMAND_OUTBOUND_DATA,RX0_Remote_Command_Outbound_Data" bitfld.long 0x10 3. " RX0_REMOTE_COMMAND_OUTBOUND_JOB_CANCEL ,RX0_Remote_Command_Outbound_Job_Cancel" "0,1" textline " " bitfld.long 0x10 2. " RX0_REMOTE_COMMAND_OUTBOUND_CLEAR_TICKET_COUNTER ,RX0_Remote_Command_Outbound_Clear_Ticket_Counter" "Not clear,Clear" textline " " bitfld.long 0x10 1. " RX0_REMOTE_COMMAND_OUTBOUND_REALIGN ,RX0_Remote_Command_Outbound_Realign" "No,Yes" textline " " bitfld.long 0x10 0. " RX0_REMOTE_COMMAND_OUTBOUND_SOFT_RESET ,RX0_Remote_Command_Outbound_Soft_Reset" "No reset,Reset" line.long 0x14 "RX1_REMOTE_CONTROLLER_OUTBOUND_STATUS,RX1_Remote_Controller_Outbound_Status" eventfld.long 0x14 31. " RX1_REMOTE_CONTROLLER_OUTBOUND_CLEAR ,RX1_Remote_Controller_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x14 0. " RX1_REMOTE_CONTROLLER_OUTBOUND_BUSY ,RX1_Remote_Controller_Outbound_Busy" "Not busy,Busy" line.long 0x18 "RX1_REMOTE_CONTROLLER_OUTBOUND_DATA,RX1_Remote_Controller_Outbound_Data" hexmask.long.byte 0x18 8.--15. 1. " RX1_REMOTE_CONTROLLER_OUTBOUND_DATA ,RX1_Remote_Controller_Outbound_Data" textline " " bitfld.long 0x18 7. " RX1_REMOTE_CONTROLLER_OUTBOUND_RW ,RX1_Remote_Controller_Outbound_RW" "0,1" textline " " hexmask.long.byte 0x18 0.--6. 1. " RX1_REMOTE_CONTROLLER_OUTBOUND_ADDRESS ,RX1_Remote_Controller_Outbound_Address" rgroup.long 0x6A8++0x03 line.long 0x00 "RX1_REMOTE_CONTROLLER_INBOUND_STATUS,RX1_Remote_Controller_Inbound_Status" bitfld.long 0x00 0. " RX1_REMOTE_CONTROLLER_INBOUND_VALID ,RX1_Remote_Controller_Inbound_Valid" "No,Yes" group.long 0x6AC++0x03 line.long 0x00 "RX1_REMOTE_CONTROLLER_INBOUND_DATA,RX1_Remote_Controller_Inbound_Data" bitfld.long 0x00 31. " RX1_REMOTE_CONTROLLER_INBOUND_ERROR ,RX1_Remote_Controller_Inbound_Error" "No error,Error" textline " " hexmask.long.byte 0x00 0.--7. 1. " RX1_REMOTE_CONTROLLER_INBOUND_RESPONSE_DATA ,RX1_Remote_Controller_Inbound_Response_Data" rgroup.long 0x6B0++0x03 line.long 0x00 "RX1_REMOTE_SERVICE_INBOUND_STATUS,RX1_Remote_Service_Inbound_Status" bitfld.long 0x00 0. " RX1_REMOTE_SERVICE_INBOUND_VALID ,RX1_Remote_Service_Inbound_Valid" "No,Yes" group.long 0x6B4++0x13 line.long 0x00 "RX1_REMOTE_SERVICE_INBOUND_DATA,RX1_Remote_Service_Inbound_Data" bitfld.long 0x00 31. " RX1_REMOTE_SERVICE_INBOUND_ERROR ,RX1_Remote_Service_Inbound_Error" "No error,Error" textline " " hexmask.long.byte 0x00 8.--15. 1. " RX1_REMOTE_SERVICE_INBOUND_DATA ,RX1_Remote_Service_Inbound_Data" textline " " bitfld.long 0x00 7. " RX1_REMOTE_SERVICE_INBOUND_RW ,RX1_Remote_Service_Inbound_RW" "0,1" textline " " hexmask.long.byte 0x00 0.--6. 1. " RX1_REMOTE_SERVICE_INBOUND_ADDRESS ,RX1_Remote_Service_Inbound_Address" line.long 0x04 "RX1_REMOTE_SERVICE_OUTBOUND_STATUS,RX1_Remote_Service_Outbound_Status" eventfld.long 0x04 31. " RX1_REMOTE_SERVICE_OUTBOUND_CLEAR ,RX1_Remote_Service_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX1_REMOTE_SERVICE_OUTBOUND_BUSY ,RX1_Remote_Service_Outbound_Busy" "Not busy,Busy" line.long 0x08 "RX1_REMOTE_SERVICE_OUTBOUND_DATA,RX1_Remote_Service_Outbound_Data" hexmask.long.byte 0x08 0.--7. 1. " RX1_REMOTE_SERVICE_OUTBOUND_READ_RESPONSE_DATA ,RX1_Remote_Service_Outbound_Read_Response_Data" line.long 0x0C "RX1_REMOTE_COMMAND_OUTBOUND_STATUS,RX1_Remote_Command_Outbound_Status" eventfld.long 0x0C 31. " RX1_REMOTE_COMMAND_OUTBOUND_CLEAR ,RX1_Remote_Command_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x0C 0. " RX1_REMOTE_COMMAND_OUTBOUND_BUSY ,RX1_Remote_Command_Outbound_Busy" "Not busy,Busy" line.long 0x10 "RX1_REMOTE_COMMAND_OUTBOUND_DATA,RX1_Remote_Command_Outbound_Data" bitfld.long 0x10 2. " RX1_REMOTE_COMMAND_OUTBOUND_CLEAR_TICKET_COUNTER ,RX1_Remote_Command_Outbound_Clear_Ticket_Counter" "Not clear,Clear" textline " " bitfld.long 0x10 1. " RX1_REMOTE_COMMAND_OUTBOUND_REALIGN ,RX1_Remote_Command_Outbound_Realign" "No,Yes" textline " " bitfld.long 0x10 0. " RX1_REMOTE_COMMAND_OUTBOUND_SOFT_RESET ,RX1_Remote_Command_Outbound_Soft_Reset" "No reset,Reset" width 12. tree.end tree "Channel 1" base ad:0x3A020000 width 31. group.long 0x00++0x07 line.long 0x00 "SWRESET,Resets APIX IP core" bitfld.long 0x00 0. " CFG_VALID ,cfg_valid" "Core in reset,Core enabled" line.long 0x04 "APIXMODE,General configuration register" bitfld.long 0x04 0. " APIX_MODE ,Apix mode" "APIX1,APIX2" group.long 0x08++0x0B line.long 0x00 "FIR_FILTER_0,Configuration for APIX transmitter FIR filter" bitfld.long 0x00 30. " C3SIGN ,Sign FIR coefficient c3" "0,1" bitfld.long 0x00 24.--29. " C3COEFF ,Value FIR coefficient c3" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x00 22. " C2SIGN ,Sign FIR coefficient c2" "0,1" bitfld.long 0x00 16.--21. " C2COEFF ,Value FIR coefficient c2" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x00 14. " C1SIGN ,Sign FIR coefficient c1" "0,1" bitfld.long 0x00 8.--13. " C1COEFF ,Value FIR coefficient c1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x00 6. " C0SIGN ,Sign FIR coefficient c0" "0,1" bitfld.long 0x00 0.--5. " C0COEFF ,Value FIR coefficient c0" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x04 "FIR_FILTER_1,Configuration for APIX transmitter FIR filter" bitfld.long 0x04 2.--4. " FIROUTCOEFF ,Defines the FIR output coefficients d4 d3 d2" "0,1,2,3,4,5,6,7" bitfld.long 0x04 0.--1. " FIRINCOEFF ,Defines the FIR input coefficients b3 b2" "0,1,2,3" line.long 0x08 "CALIB_I_TST_CFG,Calibration Test configuration" bitfld.long 0x08 31. " I_CALIB_EN ,Enable process compensation calibration" "Disabled,Enabled" rgroup.long 0x10++0x03 line.long 0x00 "CALIB_I_TST_STS,Calibration Test status" hexmask.long.word 0x00 16.--26. 1. " I_CALIB ,Internal comparator calibration value" hexmask.long.word 0x00 0.--8. 1. " I_CONTROL ,Process compensation value" group.long 0x14++0x03 line.long 0x00 "CALIB_P_TST_CFG,Calibration Prebuffer Test configuration" bitfld.long 0x00 31. " P_CALIB_EN ,Enable cable dependent calibration" "Disabled,Enabled" rgroup.long 0x18++0x03 line.long 0x00 "CALIB_P_TST_STS,Calibration Prebuffer Test status" hexmask.long.word 0x00 16.--26. 1. " P_CALIB ,Internal comparator calibration value" hexmask.long.word 0x00 0.--8. 1. " P_CONTROL ,Cable dependent calibration value" group.long 0x30++0x17 line.long 0x00 "LINKCFG,Configuration of different toplevel link functions" bitfld.long 0x00 8. " APIX1_GPIOREGEN ,Enables register access to APIX1 SBGIO port" "Disabled,Enabled" bitfld.long 0x00 7. " AICCONNECT1 ,Configuration for AIC 2:3 crossbar(AIC1)" "Disabled,Enabled" textline " " bitfld.long 0x00 6. " AICCONNECT0 ,Configuration for AIC 2:3 crossbar(AIC1)" "Disabled,Enabled" bitfld.long 0x00 4.--5. " AICMODE ,Selects data and direction for AIC pins" "Mode0 2bit AIC,Mode1 1bit AIC,Mode2 2bit AIC-2," textline " " bitfld.long 0x00 0. " PIXCH0SEL ,Selects pixel input for pixel channel 0 output" "Input 0,Input 1" line.long 0x04 "CH0PACKER_COLORCOMPONENTBITS,Color component size of outgoing pixel stream channel 0" bitfld.long 0x04 24.--27. " CH0COMPONENTBITSRED ,Number of red bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x04 16.--19. " CH0COMPONENTBITSGREEN ,Number of green bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x04 8.--11. " CH0COMPONENTBITSBLUE ,Number of blue bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "CH0PACKER_COLORCOMPONENTSHIFT,Color component offset of outgoing pixel stream channel 0" bitfld.long 0x08 24.--28. " CH0COMPONENTSHIFTRED ,Component Shift Red" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x08 16.--20. " CH0COMPONENTSHIFTGREEN ,Component Shift Green" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x08 8.--12. " CH0COMPONENTSHIFTBLUE ,Component Shift Blue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x0C "CH1PACKER_COLORCOMPONENTBITS,Color component size of outgoing pixel stream channel 1" bitfld.long 0x0C 24.--27. " CH1COMPONENTBITSRED ,Number of red bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x0C 16.--19. " CH1COMPONENTBITSGREEN ,Number of green bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x0C 8.--11. " CH1COMPONENTBITSBLUE ,Number of blue bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x10 "CH1PACKER_COLORCOMPONENTSHIFT,Color component offset of outgoing pixel stream channel 1" bitfld.long 0x10 24.--28. " CH1COMPONENTSHIFTRED ,Component Shift Red" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x10 16.--20. " CH1COMPONENTSHIFTGREEN ,Component Shift Green" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x10 8.--12. " CH1COMPONENTSHIFTBLUE ,Component Shift Blue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x14 "APIX12_CFG_0,Inova Config Byte 01" bitfld.long 0x14 0.--1. " DOWNBW ,Setting of the downstream bandwidth" ",M500mode,G1mode,G3mode" textline "" width 18. if (((per.l(ad:0x3A020000+0x04))&0x01)==0x01) group.long 0x48++0x03 line.long 0x00 "APIX12_CFG_2,Inova Config Bytes 0B_0A_09" bitfld.long 0x00 16.--17. " UPSPOFFSET750 ,Upstream sample point multiple of 750 MHz clock cycles" "0 cycles,1 cycles,2 cycles,3 cycles" bitfld.long 0x00 11.--12. " UPSPOFFSET ,Upstream sample point multiple of core clock after detect transitions" "0 cycles,1 cycles,2 cycles,3 cycles" textline " " bitfld.long 0x00 8.--9. " UPSERIALBW ,Upstream serial bandwidth" "APIX2_fast 187.5 Mbit/s,,APIX2_slow 62.5 Mbit/s," bitfld.long 0x00 5. " BACKPREN ,AShell back pressure enable" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " UPWDFAEN ,Watchdog upstream frame alignment" "Disabled,Enabled" bitfld.long 0x00 3. " UPWDBAEN ,Watchdog upstream bit alignment" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " CH1PIXEN ,Enable pixel channel1 in APIX2 core" "Disabled,Enabled" bitfld.long 0x00 0. " CH0PIXEN ,Enable pixel channel0 in APIX2 core" "Disabled,Enabled" else group.long 0x48++0x03 line.long 0x00 "APIX12_CFG_2,Inova Config Bytes 0B_0A_09" bitfld.long 0x00 16.--17. " UPSPOFFSET750 ,Upstream sample point multiple of 750 MHz clock cycles" "0 cycles,1 cycles,2 cycles,3 cycles" bitfld.long 0x00 11.--12. " UPSPOFFSET ,Upstream sample point multiple of core clock after detect transitions" "0 cycles,1 cycles,2 cycles,3 cycles" textline " " bitfld.long 0x00 8.--9. " UPSERIALBW ,Upstream serial bandwidth" ",APIX1_fast 62.5 Mbit/s,,APIX1_slow 31.25 Mbit/s" bitfld.long 0x00 5. " BACKPREN ,AShell back pressure enable" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " UPWDFAEN ,Watchdog upstream frame alignment" "Disabled,Enabled" bitfld.long 0x00 3. " UPWDBAEN ,Watchdog upstream bit alignment" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " CH1PIXEN ,Enable pixel channel1 in APIX2 core" "Disabled,Enabled" bitfld.long 0x00 0. " CH0PIXEN ,Enable pixel channel0 in APIX2 core" "Disabled,Enabled" endif group.long 0x50++0x03 line.long 0x00 "APIX2_CFG_1,Inova COnfig Bytes 10_0F_0E_0D" bitfld.long 0x00 31. " ASHELL2_1_BROADCASTEN ,Broadcast mode of AShell2_1" "Disabled,Enabled" bitfld.long 0x00 30. " ASHELL2_1_LINKERRORTOL ,Link error tolerance of AShell2_1" "0,1" textline " " bitfld.long 0x00 26.--29. " ASHELL2_1_CRCTOCNT ,CRC timeout counter of AShell2_1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 25. " ASHELL2_1_ARQ_DIS ,Disable ARQ of AShell2_1" "No,Yes" textline " " bitfld.long 0x00 24. " ASHELL2_1_EN ,AShell2_1 enable" "Disabled,Enabled" bitfld.long 0x00 23. " ASHELL2_0_BROADCASTEN ,Broadcast mode of AShell2_0" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " ASHELL2_0_LINKERRORTOL ,Link error tolerance of AShell2_0" "0,1" bitfld.long 0x00 18.--21. " ASHELL2_0_CRCTOCNT ,CRC timeout counter of AShell2_0" "Disabled,4,6,10,8,16,24,40,32,64,96,160,256,512,768,1280" textline " " bitfld.long 0x00 17. " ASHELL2_0_ARQ_DIS ,Disable ARQ of AShell2_0" "Yes,No" bitfld.long 0x00 16. " ASHELL2_0_EN ,AShell2_0 enable" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " AUDIOEN ,Audio Interface enable" "Disabled,Enabled" bitfld.long 0x00 10. " AUDIOBW ,Audio bandwidth" "Ordinary bandwidth,High bandwidth" textline " " bitfld.long 0x00 9. " RXDAISYCHAIN ,RX daisy chain" "1 Apix2 DC off,2 Apix2 DC on" if (((per.l(ad:0x3A020000+0x44))&0x03)==0x01) group.long 0x54++0x03 line.long 0x00 "APIX2_CFG_2,Inova Config Bytes 13_12_11" bitfld.long 0x00 22. " GPIODWNBW ,GPIO downstream bandwidth mode" "Low speed,High speed" bitfld.long 0x00 21. " GPIODWNHALFBW ,Halve GPIO downstream bandwidth" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " GPIOUPBW ,GPIO upstream bandwidth mode" "Low speed,High speed" textline " " bitfld.long 0x00 19. " GPIO0UPEN ,GPIO0 upstream channel enable" "Disabled,Enabled" bitfld.long 0x00 18. " GPIO1UPEN ,GPIO1 upstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " GPIO0DWNEN ,GPIO0 downstream channel enable" "Disabled,Enabled" bitfld.long 0x00 16. " GPIO1DWNEN ,GPIO1 downstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 14.--15. " ASH2DWNDIV ,AShell2 downstream bandwidth divider" "/1,/2,/4,/8" bitfld.long 0x00 9.--13. " DOWNDATABW ,Totally available downstream bandwidth for AShell data audio and GPIO" ",56 MBit/s,42 MBit/s,,29 MBit/s,,,,15 MBit/s,,,,,,,,1.3 MBit/s,..." textline " " bitfld.long 0x00 6. " BULKDATAEN ,Bulk data mode" "Disabled,Enabled" bitfld.long 0x00 5. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24bits,21 bits" textline " " bitfld.long 0x00 3.--4. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "BpP10,BpP12,BpP18,BpP24" bitfld.long 0x00 2. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24bits,21bits" textline " " bitfld.long 0x00 0.--1. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "BpP10,BpP12,BpP18,BpP24" elif (((per.l(ad:0x3A020000+0x44))&0x03)==0x02) group.long 0x54++0x03 line.long 0x00 "APIX2_CFG_2,Inova Config Bytes 13_12_11" bitfld.long 0x00 22. " GPIODWNBW ,GPIO downstream bandwidth mode" "Low speed,High speed" bitfld.long 0x00 21. " GPIODWNHALFBW ,Halve GPIO downstream bandwidth" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " GPIOUPBW ,GPIO upstream bandwidth mode" "Low speed,High speed" textline " " bitfld.long 0x00 19. " GPIO0UPEN ,GPIO0 upstream channel enable" "Disabled,Enabled" bitfld.long 0x00 18. " GPIO1UPEN ,GPIO1 upstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " GPIO0DWNEN ,GPIO0 downstream channel enable" "Disabled,Enabled" bitfld.long 0x00 16. " GPIO1DWNEN ,GPIO1 downstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 14.--15. " ASH2DWNDIV ,AShell2 downstream bandwidth divider" "/1,/2,/4,/8" bitfld.long 0x00 9.--13. " DOWNDATABW ,Totally available downstream bandwidth for AShell data audio and GPIO" ",113 MBit/s,85 MBit/s,,58 MBit/s,,,,30 MBit/s,..." textline " " bitfld.long 0x00 6. " BULKDATAEN ,Bulk data mode" "Disabled,Enabled" bitfld.long 0x00 5. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24bits,21 bits" textline " " bitfld.long 0x00 3.--4. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "10bit per pixel,12bit per pixel,18bit per pixel,24" bitfld.long 0x00 2. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24bits,21bits" textline " " bitfld.long 0x00 0.--1. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "10bit per pixel,12bit per pixel,18bit per pixel,24" elif (((per.l(ad:0x3A020000+0x44))&0x03)==0x03) group.long 0x54++0x03 line.long 0x00 "APIX2_CFG_2,Inova Config Bytes 13_12_11" bitfld.long 0x00 22. " GPIODWNBW ,GPIO downstream bandwidth mode" "Low speed,High speed" bitfld.long 0x00 21. " GPIODWNHALFBW ,Halve GPIO downstream bandwidth" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " GPIOUPBW ,GPIO upstream bandwidth mode" "Low speed,High speed" textline " " bitfld.long 0x00 19. " GPIO0UPEN ,GPIO0 upstream channel enable" "Disabled,Enabled" bitfld.long 0x00 18. " GPIO1UPEN ,GPIO1 upstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " GPIO0DWNEN ,GPIO0 downstream channel enable" "Disabled,Enabled" bitfld.long 0x00 16. " GPIO1DWNEN ,GPIO1 downstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 14.--15. " ASH2DWNDIV ,AShell2 downstream bandwidth divider" "/1,/2,/4,/8" bitfld.long 0x00 9.--13. " DOWNDATABW ,Totally available downstream bandwidth for AShell data audio and GPIO" ",340 MBit/s,257 MBit/s,,174 MBit/s,,,,91 MBit/s,..." textline " " bitfld.long 0x00 6. " BULKDATAEN ,Bulk data mode" "Disabled,Enabled" bitfld.long 0x00 5. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24bits,21 bits" textline " " bitfld.long 0x00 3.--4. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "BpP10,BpP12,BpP18,BpP24" bitfld.long 0x00 2. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24bits,21bits" textline " " bitfld.long 0x00 0.--1. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "BpP10,BpP12,BpP18,BpP24" else group.long 0x54++0x03 line.long 0x00 "APIX2_CFG_2,Inova Config Bytes 13_12_11" bitfld.long 0x00 22. " GPIODWNBW ,GPIO downstream bandwidth mode" "Low speed,High speed" bitfld.long 0x00 21. " GPIODWNHALFBW ,Halve GPIO downstream bandwidth" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " GPIOUPBW ,GPIO upstream bandwidth mode" "Low speed,High speed" textline " " bitfld.long 0x00 19. " GPIO0UPEN ,GPIO0 upstream channel enable" "Disabled,Enabled" bitfld.long 0x00 18. " GPIO1UPEN ,GPIO1 upstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " GPIO0DWNEN ,GPIO0 downstream channel enable" "Disabled,Enabled" bitfld.long 0x00 16. " GPIO1DWNEN ,GPIO1 downstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 14.--15. " ASH2DWNDIV ,AShell2 downstream bandwidth divider" "/1,/2,/4,/8" textline " " bitfld.long 0x00 6. " BULKDATAEN ,Bulk data mode" "Disabled,Enabled" bitfld.long 0x00 5. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24bits,21 bits" textline " " bitfld.long 0x00 3.--4. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "BpP10,BpP12,BpP18,BpP24" bitfld.long 0x00 2. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24bits,21bits" textline " " bitfld.long 0x00 0.--1. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "BpP10,BpP12,BpP18,BpP24" endif group.long 0x58++0x17 line.long 0x00 "APIX1_CFG_0,Inova Config Byte 14" hexmask.long.byte 0x00 24.--30. 1. " SBDOWN_DATA_CYCLETIME6TO0 ,Cycle time of sbdown clock in multiples of 8ns" line.long 0x04 "APIX1_CFG_1,Inova Config Bytes 18_17_16_15" bitfld.long 0x04 27.--28. " PX_CTRL_PIGGYBACK ,APIX PHY (Soft IP): transmission of pixel controls" "Never,Unused,With even pixels only,With every pixel" bitfld.long 0x04 25.--26. " PIXEL_DATA_WIDTH ,Pixel data width" "10bit per pixel,12bit per pixel,18bit per pixel,24" textline " " bitfld.long 0x04 23. " ARQ_DISABLE ,Retransmission disable" "No,Yes" bitfld.long 0x04 22. " SUPPRESS_IDLE ,Suppress idle transmission to reduce data traffic" "Disabled,Enabled" textline " " bitfld.long 0x04 16.--18. " SBDOWN_DATA_CYCLETIME9TO7 ,Upper bits of sbdown_data_cycletime" "0,1,2,3,4,5,6,7" bitfld.long 0x04 12.--15. " CRC_TIME_OUT_VALUE ,CRC timeout value" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x04 8.--11. " WINDOW_SIZE ,AShell window size Window size of the retransmission protocol" ",1,2,3,4,5,6,7,8,9,10,11,12,,," bitfld.long 0x04 7. " SBUP_DWIDTH ,Enable sbup data ports" "1 bit,2 bit" textline " " bitfld.long 0x04 6. " SBUP_DACLK ,Validate sbup_data automatic or with transmitted valid" "Disabled,Enabled" bitfld.long 0x04 5. " SBDOWN_DWIDTH ,Enable sbdown data ports" "1 bit data and valid,2 bit data" textline " " bitfld.long 0x04 3.--4. " SBDOWN_DACLK ,Generate sbdown clock and transmit as sbdown_data[1]" ",Sbdown_trigger,Internal counter," bitfld.long 0x04 1. " ESHELLEN ,Connect internal APIX1 PHY to external sideband data through APIX1 SBGPIO (AIC) interface" "Disabled,Enabled" textline " " bitfld.long 0x04 0. " SPI_OVER_SB ,Selects between two different sideband transmission modes" "Full data mode,SPI mode" line.long 0x08 "APIX1_CFG_2,Inova Config Bytes 1C_1B_1A_19" hexmask.long.byte 0x08 25.--31. 1. " SBDOWN_CLOCK_HIGH_PULSE ,Configure high pulse width of signal 'sb_down_clk' if sb_down_clk and sb_up_clk enable" hexmask.long.byte 0x08 17.--23. 1. " SBDOWN_CLOCK_CYCLES ,Configures sbdown clk cycle" textline " " bitfld.long 0x08 15. " DDOWN_ENABLE ,APIX PHY (Soft IP) / AShell: configure downstream data path" "Pixel stream mode,Data mode" bitfld.long 0x08 14. " EXT_SB_DATA_DIS ,Sideband data are 2-stage registered internal have to be used with external sideband data" "External,No external" textline " " bitfld.long 0x08 11. " ASHELL1_EN ,APIX1 Ashell1" "Disabled,Enabled" bitfld.long 0x08 10. " SB_CLK_EN ,Enable sb_down_clk and sb_up_clk" "Disabled,Enabled" textline " " bitfld.long 0x08 8.--9. " SB_UP_CLK_CYCLES ,Configure high pulse width of signal 'sb_up_clk' if sb_down_clk and sb_up_clk enable" "1cycle,2cycles,3cysles,4cycles" line.long 0x0C "APIX1_CFG_3,Inova Config Byte 1D" hexmask.long.byte 0x0C 1.--7. 1. " SBDOWN_CLOCK_START_POS ,Start position of signal sbdown_clk relative to internal \u2018strobe position\u2019" line.long 0x10 "TEST_CONFIG,Config for Inova BIST Test" hexmask.long.word 0x10 16.--31. 1. " TEST_PATTERN ,Test pattern" bitfld.long 0x10 12. " TESTPATTERN_EN ,Test pattern generation" "Disabled,Enabled" textline " " bitfld.long 0x10 11. " PSRTEST_MODE ,PSR test pattern generation" "Disabled,Enabled" bitfld.long 0x10 9.--10. " PSRTEST_8B10B ,Psr Test 8B10B" "Run length 8,Run length 10,Run length 12,Run length 16" textline " " bitfld.long 0x10 8. " BG_MASK_DISABLE ,Line coder mask disable" "No,Yes" line.long 0x14 "AAC,Configuration for AShell1-to-AShell1 - Connector (AAC)" bitfld.long 0x14 14.--15. " AACOFFSET ,Cfg_data[15:14] offset between edges of AAC clock and AAC data[1:0] as multiples of core clock" "1cycle,2cycles,3cycles,4cycles" hexmask.long.word 0x14 2.--13. 1. " AACFREQUENCY ,Defines AAC clock frequency" textline " " bitfld.long 0x14 1. " AACEN ,Data path selection" "APIX1 PHY,ACC" bitfld.long 0x14 0. " AACMODE ,AAC clock mode" "Both edges,Rising edges" group.long 0x70++0x0B line.long 0x00 "AAA,Configuration for Ashell1-to-Ashell2 Adapter" bitfld.long 0x00 1. " AAAEN ,AShell1 to AShell2 Adapter enable" "Disabled,Enabled" bitfld.long 0x00 0. " ASHELL2_SELECT ,Ashell2 select" "AShell2_1,AShell2_0" line.long 0x04 "APIX1_GPO,GPIO DATA for APIX1 communication" bitfld.long 0x04 0.--1. " APIX1_GPO ,2 bit GPIO output data corresponds to GPIO pins of INAP1 device" "0,1,2,3" line.long 0x08 "APIX1_GPI_INTCFG,APIX1GPI INTCFG" bitfld.long 0x08 1. " APIX1_GPI_INTCFG ,APIX1_GPI_INTCFG" "Rising edge,Falling edge" bitfld.long 0x08 0. " APIX0_GPI_INTCFG ,APIX0_GPI_INTCFG" "Rising edge,Falling edge" rgroup.long 0x7C++0x03 line.long 0x00 "APIX1_GPI,GPIO DATA for APIX1 communication" bitfld.long 0x00 0.--1. " APIX1_GP1 ,2 bit GPIO output data corresponds to GPIO pins of INAP1 device" "0,1,2,3" group.long 0x80++0x07 line.long 0x00 "APIX2_GPO,GPIO DATA for APIX2 communication" bitfld.long 0x00 0.--1. " APIX2_GPO ,2 bit GPIO output data corresponds to GPIO pins of INAP1 device" "0,1,2,3" line.long 0x04 "APIX2_GPI_INTCFG,APIX2_GPI_INTCFG" bitfld.long 0x04 3. " APIX2_GPI_INTCFG[3] ,APIX2_GPI_INTCFG[3]" "Rising edge,Falling edge" bitfld.long 0x04 2. " APIX2_GPI_INTCFG[2] ,APIX2_GPI_INTCFG[2]" "Rising edge,Falling edge" textline " " bitfld.long 0x04 1. " APIX2_GPI_INTCFG[1] ,APIX2_GPI_INTCFG[1]" "Rising edge,Falling edge" bitfld.long 0x04 0. " APIX2_GPI_INTCFG[0] ,APIX2_GPI_INTCFG[0]" "Rising edge,Falling edge" rgroup.long 0x88++0x03 line.long 0x00 "APIX2_GPI,GPIO DATA for APIX2 communication" bitfld.long 0x00 0.--3. " APIX2_GPI ,2 bit GPIO input data, corresponds to GPIO pins of INAP1 device" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" group.long 0x200++0x07 line.long 0x00 "APIX_CTRL_0,Signals to AShell restart and counter clears" eventfld.long 0x00 4. " ASHELL2_1_TCNT_CLEAR ,AShell2_1_tcnt_clear" "Not clear,Clear" eventfld.long 0x00 3. " ASHELL2_0_TCNT_CLEAR ,AShell2_0_tcnt_clear" "Not clear,Clear" textline " " eventfld.long 0x00 2. " ASHELL1_REALIGN ,Apix1 AShell realign by writing a 1" "Not realign,Realign" eventfld.long 0x00 1. " ASHELL2_1_REALIGN ,AShell2_1 realign by writing a 1" "Not realign,Realign" textline " " eventfld.long 0x00 0. " ASHELL2_0_REALIGN ,AShell2_0 realign by writing a 1" "Not realign,Realign" line.long 0x04 "APIX_CTRL_1,Reset for counter values" eventfld.long 0x04 5. " ASHELL2_0_CRCERRCNTCLEAR ,Clear Ashell2_0_CRCErrCnt by writing a 1" "Not clear,Clear" eventfld.long 0x04 4. " ASHELL2_1_CRCERRCNTCLEAR ,Clear Ashell2_1_CRCErrCnt by writing a 1" "Not clear,Clear" textline " " eventfld.long 0x04 3. " APIX1UPFALIGNERRCNTCLEAR ,Clear Apix1upFAlignErrCnt by writing a 1" "Not clear,Clear" eventfld.long 0x04 2. " ASHELL1_CRCERRCNTCLEAR ,Clear Ashell2_1_CRCErrCnt by writing a 1" "Not clear,Clear" textline " " eventfld.long 0x04 1. " APIX2UPFALIGNERRCNTCLEAR ,Clear Apix2upFAlignErrCnt by writing a 1" "Not clear,Clear" group.long 0x208++0x0B line.long 0x00 "APIX12_STATUS_0,Status from Inova Status bytes 01 and 02 PHY status pixelstream status" rbitfld.long 0x00 12. " APIX2UPFALIGN ,Apix2 upstream frame aligned" "No,Yes" rbitfld.long 0x00 8.--11. " APIX2UPFALIGNERRCNT ,APIX2 upstream frame aligned error counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 0. " UPBITALIGNED ,Upstream bit aligned" "0,1" line.long 0x04 "APIX2_STATUS_0,Status from Inova Status bytes 06_05_04_03 Pixelstream status Ashell2_0 Status" hexmask.long.byte 0x04 24.--31. 1. " ASHELL2_0_TADIFFCNT ,Transaction counter difference of AShell2_0" rbitfld.long 0x04 17. " ASHELL2_0_OPERATIONAL ,AShell operational" "Not asserted,Asserted" textline " " hexmask.long.byte 0x04 8.--15. 1. " ASHELL2_0_CRCERRCNT ,CRC error counter of AShell2_0" rbitfld.long 0x04 7. " CH1HSYNCPOL ,Pixel channel 1 horizontal polarity" "Active low,Active high" textline " " rbitfld.long 0x04 6. " CH1VSYNCPOL ,Pixel channel 1 vertical polarity" "Active low,Active high" rbitfld.long 0x04 5. " CH1PIXFIFOEMPTY ,Pixel channel 1 FIFO underflow" "No,Yes" textline " " rbitfld.long 0x04 4. " CH1PIXFIFOFULL ,Pixel channel 1 FIFO overflow" "No,Yes" rbitfld.long 0x04 3. " CH0HSYNCPOL ,Pixel channel 0 horizontal polarity" "Active low,Active high" textline " " rbitfld.long 0x04 2. " CH0VSYNCPOL ,Pixel channel 0 vertical polarity" "Active low,Active high" rbitfld.long 0x04 1. " CH0PIXFIFOEMPTY ,Pixel channel 0 FIFO underflow" "No,Yes" textline " " bitfld.long 0x04 0. " CH0PIXFIFOFULL ,Pixel channel 0 FIFO overflow" "No,Yes" line.long 0x08 "APIX2_STATUS_1,Status from Inova Status bytes 09_08_07 Ashell2_1 status" hexmask.long.byte 0x08 24.--31. 1. " ASHELL2_1_TADIFFCNT ,Transaction counter difference of AShell2_1" rbitfld.long 0x08 17. " ASHELL2_1_OPERATIONAL ,AShell operational" "Not asserted,Asserted" textline " " hexmask.long.byte 0x08 8.--15. 1. " ASHELL2_1_CRCERRCNT ,CRC error counter of AShell2_0 Number of received CRC errors" rgroup.long 0x214++0x03 line.long 0x00 "APIX1_STATUS_0,Status from Inova Status bytes 0C_0B_0A Ashell1 and APIX1 PHY" bitfld.long 0x00 22. " APIX1UPFRAMEALIGNED ,Apix1 upstream frame aligned" "No,Yes" bitfld.long 0x00 16.--21. " APIX1UPFRAMEALIGNEDERRCNT ,Apix1 upstream frame aligned error counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x00 8.--13. " ASHELL1_CRCERRCNT ,Apix1 AShell CRC error counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 6. " ASHELL1_OPERATIONAL ,Apix1 AShell operational" "Not asserted,Asserted" tree "Interrupt registers" width 13. rgroup.long 0x300++0x0B line.long 0x00 "INTSTATUS0,Interrupt Status Register 0" bitfld.long 0x00 31. " RX1_REMOTE_INBOUND_I2C_JOB_CANCEL ,APIX2 Remote command cancel I2C job received from device RX1" "Inactive,Active" bitfld.long 0x00 30. " RX1_REMOTE_INBOUND_ASHELL2_CLEAR_TICKET_COUNTER ,APIX2 Remote command clear Ashell2 ticket counter received from device RX1" "Inactive,Active" textline " " bitfld.long 0x00 29. " RX1_REMOTE_INBOUND_ASHELL2_REALIGN ,APIX2 Remote command realign Ashell2 received from device RX1" "Inactive,Active" bitfld.long 0x00 28. " RX1_REMOTE_INBOUND_SOFT_RESET ,APIX2 Remote command soft reset received from device RX1" "Inactive,Active" textline " " bitfld.long 0x00 27. " RX0_REMOTE_INBOUND_I2C_JOB_CANCEL ,APIX2 Remote command cancel I2C job received from device RX0" "Inactive,Active" bitfld.long 0x00 26. " RX0_REMOTE_INBOUND_ASHELL2_CLEAR_TICKET_COUNTER ,APIX2 Remote command clear Ashell2 ticket counter received from device RX0" "Inactive,Active" textline " " bitfld.long 0x00 25. " RX0_REMOTE_INBOUND_ASHELL2_REALIGN ,APIX2 Remote command realign Ashell2 received from device RX0" "Inactive,Active" bitfld.long 0x00 24. " RX0_REMOTE_INBOUND_SOFT_RESET ,APIX2 Remote command soft reset received from device RX0" "Inactive,Active" textline " " bitfld.long 0x00 23. " GPI_1 ,APIX1 GPIO Edge detected at APIX1 GPI_1 port" "Inactive,Active" bitfld.long 0x00 22. " GPI_0 ,APIX1 GPIO Edge detected at APIX1 GPI_0 port" "Inactive,Active" textline " " bitfld.long 0x00 21. " ASHELL1_FATAL ,APIX1 Ashell1 Fatal Error" "Inactive,Active" bitfld.long 0x00 20. " ASHELL1_CRCERROR ,APIX1 Ashell1 detected CRC error at incoming data" "Inactive,Active" textline " " bitfld.long 0x00 19. " ASHELL1_UNCONNECTED ,APIX1 Ashell1 unconnected with remote Ashell" "Inactive,Active" bitfld.long 0x00 18. " ASHELL1_CONNECTED ,APIX1 Ashell1 connected with remote Ashell" "Inactive,Active" textline " " bitfld.long 0x00 17. " ASHELL1_CRCTIMEOUT ,APIX1 Ashell1 CRC error threshold was reached" "Inactive,Active" bitfld.long 0x00 16. " ASHELL1_PROTERR ,APIX1 Ashell1 Protocoll Error" "Inactive,Active" textline " " bitfld.long 0x00 15. " ASHELL1_REMRESTARTED ,APIX1 Ashell1 Remote Ashell1 was restarted" "Inactive,Active" bitfld.long 0x00 14. " ASHELL2_1_UNCONNECTED ,APIX2 Ashell2_1 unconnected with remote Ashell" "Inactive,Active" textline " " bitfld.long 0x00 13. " ASHELL2_1_CONNECTED ,APIX2 Ashell2_1 connected with remote Ashell" "Inactive,Active" bitfld.long 0x00 12. " ASHELL2_1_TRANSACTION_LOSS ,APIX2 Ashell2_1 Transaction Loss Error" "Inactive,Active" textline " " bitfld.long 0x00 11. " ASHELL2_1_FATAL ,APIX2 Ashell2_1 Fatal Error" "Inactive,Active" bitfld.long 0x00 10. " ASHELL2_1_CRCERROR ,APIX2 Ashell2_1 CRC error" "Inactive,Active" textline " " bitfld.long 0x00 9. " ASHELL2_0_UNCONNECTED ,APIX2 Ashell2_0 unconnected with remote Ashell" "Inactive,Active" bitfld.long 0x00 8. " ASHELL2_0_CONNECTED ,APIX2 Ashell2_0 connected with remote Ashell" "Inactive,Active" textline " " bitfld.long 0x00 7. " ASHELL2_0_TRANSACTION_LOSS ,APIX2 Ashell2_0 Transaction Loss Error" "Inactive,Active" bitfld.long 0x00 6. " ASHELL2_0_FATAL ,APIX2 Ashell2_0 Fatal Error" "Inactive,Active" textline " " bitfld.long 0x00 5. " ASHELL2_0_CRCERROR ,APIX2 Ashell2_0 CRC error" "Inactive,Active" bitfld.long 0x00 4. " CH0PIXFIFOFULL_INT ,APIX2 PIX Channel 0 pixelfifo overflow error" "Inactive,Active" textline " " bitfld.long 0x00 3. " CH0PIXFIFOEMPTY_INT ,APIX2 PIX Channel 0 pixelfiifo underflow error" "Inactive,Active" bitfld.long 0x00 2. " CH1PIXFIFOFULL_INT ,APIX2 PIX Channel 1 pixelfifo overflow error" "Inactive,Active" textline " " bitfld.long 0x00 1. " CH1PIXFIFOEMPTY_INT ,APIX2 PIX Channel 1 pixelfiifo underflow error" "Inactive,Active" bitfld.long 0x00 0. " UPBITALIGNEDLOSS ,PHY Loss of upstream PHY Bit alignment" "Inactive,Active" line.long 0x04 "INTSTATUS1,Interrupt Status Register 1" bitfld.long 0x04 31. " RX1_REMOTE_SERVICE_INBOUND_ERROR_INT ,APIX2 remote IF Data loss at inbound remote service data register (Rx1)" "Inactive,Active" bitfld.long 0x04 30. " RX1_REMOTE_SERVICE_INBOUND_VALID_INT ,APIX2 remote IF Received valid inbound data from remote service IF of device RX1" "Inactive,Active" textline " " bitfld.long 0x04 29. " RX1_REMOTE_CONTROLLER_INBOUND_ERROR_INT ,APIX2 remote IF Data loss at inbound remote control data register (RX1)" "Inactive,Active" bitfld.long 0x04 28. " RX1_REMOTE_CONTROLLER_INBOUND_VALID_INT ,APIX2 remote IF Received valid inbound data from remote control IF of device RX1" "Inactive,Active" textline " " bitfld.long 0x04 27. " RX0_REMOTE_SERVICE_INBOUND_ERROR_INT ,APIX2 remote IF Data loss at inbound remote service data register (Rx0)" "Inactive,Active" bitfld.long 0x04 26. " RX0_REMOTE_SERVICE_INBOUND_VALID_INT ,APIX2 remote IF Received valid inbound data from remote service IF of device RX0" "Inactive,Active" textline " " bitfld.long 0x04 25. " RX0_REMOTE_CONTROLLER_INBOUND_ERROR_INT ,APIX2 remote IF Data loss at inbound remote control data register (RX0)" "Inactive,Active" bitfld.long 0x04 24. " RX0_REMOTE_CONTROLLER_INBOUND_VALID_INT ,APIX2 remote IF Received valid inbound data from remote control IF of device RX0" "Inactive,Active" textline " " bitfld.long 0x04 23. " RX1_I2C_INBOUND_READ_RESPONSE_ERROR_INT ,APIX2 remote IF Data loss at i2c inbound read response register (RX1)" "Inactive,Active" bitfld.long 0x04 22. " RX1_I2C_INBOUND_READ_RESPONSE_VALID_INT ,APIX2 I2C Received valid inbound I2C read response from device RX1" "Inactive,Active" textline " " bitfld.long 0x04 21. " RX1_I2C_INBOUND_STATUS_ERROR_INT ,APIX2 I2C Data loss at inbound i2c status register (RX1)" "Inactive,Active" bitfld.long 0x04 20. " RX1_I2C_INBOUND_STATUS_VALID_INT ,APIX2 I2C Received valid inbound i2c status from device RX1" "Inactive,Active" textline " " bitfld.long 0x04 19. " RX1_I2C_INBOUND_JOB_SPEC_ERROR_INT ,APIX2 I2C Data loss at i2c job specification register (RX1)" "Inactive,Active" bitfld.long 0x04 18. " RRX1_I2C_INBOUND_JOB_SPEC_VALID_INT ,APIX2 I2C Received valid inbound i2c job specification from device RX1" "Inactive,Active" textline " " bitfld.long 0x04 17. " RX0_I2C_INBOUND_READ_RESPONSE_ERROR_INT ,APIX2 I2C Data loss at i2c inbound read response register (RX0)" "Inactive,Active" bitfld.long 0x04 16. " RX0_I2C_INBOUND_READ_RESPONSE_VALID_INT ,APIX2 I2C Received valid inbound I2C read response from device RX0" "Inactive,Active" textline " " bitfld.long 0x04 15. " RX0_I2C_INBOUND_STATUS_ERROR_INT ,APIX2 I2C Data loss at inbound i2c status register (RX0)" "Inactive,Active" bitfld.long 0x04 14. " RX0_I2C_INBOUND_STATUS_VALID_INT ,APIX2 I2C Received valid inbound i2c status from device RX0" "Inactive,Active" textline " " bitfld.long 0x04 13. " RX0_I2C_INBOUND_JOB_SPEC_ERROR_INT ,APIX2 I2C Data loss at i2c job specification register (RX0)" "Inactive,Active" bitfld.long 0x04 12. " RX0_I2C_INBOUND_JOB_SPEC_VALID_INT ,APIX2 I2C Received valid inbound i2c job specification from device RX0" "Inactive,Active" textline " " bitfld.long 0x04 11. " WDG_TIMEOUT_INT ,Message buffer Wrbuf Watchdog timeout" "Inactive,Active" bitfld.long 0x04 10. " WRBUF_EMPTY_INT ,Message buffer Write buffer #1 becomes empty" "Inactive,Active" textline " " bitfld.long 0x04 9. " WRBUF_FULL_INT ,Message buffer Write buffer #1 becomes full" "Inactive,Active" bitfld.long 0x04 8. " R1BUF_NOT_EMPTY ,Message buffer Read buffer #1 becomes not empty" "Inactive,Active" textline " " bitfld.long 0x04 7. " R1BUF_FULL_INT ,Message buffer Read buffer #1 becomes full" "Inactive,Active" bitfld.long 0x04 6. " R0BUF_NOT_EMPTY ,Message buffer Read buffer #0 becomes not empty" "Inactive,Active" textline " " bitfld.long 0x04 5. " R0BUF_FULL_INT ,Message buffer Read buffer #0 becomes full" "Inactive,Active" bitfld.long 0x04 4. " WRBUF_OVERFLOW ,Message buffer Write buffer overflow" "Inactive,Active" textline " " bitfld.long 0x04 3. " R1BUF_UNDERRUN ,Message buffer Read buffer #1 underrun" "Inactive,Active" bitfld.long 0x04 2. " R1BUF_OVERFLOW ,Message buffer Read buffer #1 overflow" "Inactive,Active" textline " " bitfld.long 0x04 1. " R0BUF_UNDERRUN ,Message buffer Read buffer #0 underrun" "Inactive,Active" bitfld.long 0x04 0. " R0BUF_OVERFLOW ,Message buffer Read buffer #0 overflow" "Inactive,Active" line.long 0x08 "INTSTATUS2,Interrupt Status Register 2" bitfld.long 0x08 6. " FRAME_ALIGNMENT_TIMEOUT_DETECT ,PHY signalizes that the device was not frame aligned" "Inactive,Active" bitfld.long 0x08 5. " DEBUG_TIMEOUT ,APIX2TX_link Abort of read access to debug register happened" "Inactive,Active" textline " " bitfld.long 0x08 4. " STATUS_TIMEOUT ,APIX2TX_link Abort of read access to status register happened" "Inactive,Active" bitfld.long 0x08 3. " APIX2_GPI_1_RX1 ,APIX2 GPIO Rising or falling edge detected at APIX2 GPI1 from device RX1" "Inactive,Active" textline " " bitfld.long 0x08 2. " APIX2_GPI_0_RX1 ,APIX2 GPIO Rising or falling edge detected at APIX2 GPI0 from device RX1" "Inactive,Active" bitfld.long 0x08 1. " APIX2_GPI_1_RX0 ,APIX2 GPIO Rising or falling edge detected at APIX2 GPI1 from device RX0" "Inactive,Active" textline " " bitfld.long 0x08 0. " APIX2_GPI_0_RX0 ,APIX2 GPIO Rising or falling edge detected at APIX2 GPI0 from device RX0" "Inactive,Active" textline "" ;section group.long 0x30C++0x2F line.long 0x00 "INT0ENABLE0,Interrupt Enable Register 0 for interrupts bits" bitfld.long 0x00 31. " INT0ENABLE0_[31] ,Interrupt 0 Enable bit 31" "Disabled,Enabled" bitfld.long 0x00 30. " [30] ,Interrupt 0 Enable bit 30" "Disabled,Enabled" bitfld.long 0x00 29. " [29] ,Interrupt 0 Enable bit 29" "Disabled,Enabled" bitfld.long 0x00 28. " [28] ,Interrupt 0 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x00 27. " [27] ,Interrupt 0 Enable bit 27" "Disabled,Enabled" bitfld.long 0x00 26. " [26] ,Interrupt 0 Enable bit 26" "Disabled,Enabled" bitfld.long 0x00 25. " [25] ,Interrupt 0 Enable bit 25" "Disabled,Enabled" bitfld.long 0x00 24. " [24] ,Interrupt 0 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x00 23. " [23] ,Interrupt 0 Enable bit 23" "Disabled,Enabled" bitfld.long 0x00 22. " [22] ,Interrupt 0 Enable bit 22" "Disabled,Enabled" bitfld.long 0x00 21. " [21] ,Interrupt 0 Enable bit 21" "Disabled,Enabled" bitfld.long 0x00 20. " [20] ,Interrupt 0 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " [19] ,Interrupt 0 Enable bit 19" "Disabled,Enabled" bitfld.long 0x00 18. " [18] ,Interrupt 0 Enable bit 18" "Disabled,Enabled" bitfld.long 0x00 17. " [17] ,Interrupt 0 Enable bit 17" "Disabled,Enabled" bitfld.long 0x00 16. " [16] ,Interrupt 0 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x00 15. " [15] ,Interrupt 0 Enable bit 15" "Disabled,Enabled" bitfld.long 0x00 14. " [14] ,Interrupt 0 Enable bit 14" "Disabled,Enabled" bitfld.long 0x00 13. " [13] ,Interrupt 0 Enable bit 13" "Disabled,Enabled" bitfld.long 0x00 12. " [12] ,Interrupt 0 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " [11] ,Interrupt 0 Enable bit 11" "Disabled,Enabled" bitfld.long 0x00 10. " [10] ,Interrupt 0 Enable bit 10" "Disabled,Enabled" bitfld.long 0x00 9. " [9] ,Interrupt 0 Enable bit 9" "Disabled,Enabled" bitfld.long 0x00 8. " [8] ,Interrupt 0 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " [7] ,Interrupt 0 Enable bit 7" "Disabled,Enabled" bitfld.long 0x00 6. " [6] ,Interrupt 0 Enable bit 6" "Disabled,Enabled" bitfld.long 0x00 5. " [5] ,Interrupt 0 Enable bit 5" "Disabled,Enabled" bitfld.long 0x00 4. " [4] ,Interrupt 0 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " [3] ,Interrupt 0 Enable bit 3" "Disabled,Enabled" bitfld.long 0x00 2. " [2] ,Interrupt 0 Enable bit 2" "Disabled,Enabled" bitfld.long 0x00 1. " [1] ,Interrupt 0 Enable bit 1" "Disabled,Enabled" bitfld.long 0x00 0. " [0] ,Interrupt 0 Enable bit 0" "Disabled,Enabled" line.long 0x04 "INT0ENABLE1,Interrupt Enable Register 1 for interrupts bits" bitfld.long 0x04 31. " INT0ENABLE1_[31] ,Interrupt 0 Enable bit 31" "Disabled,Enabled" bitfld.long 0x04 30. " [30] ,Interrupt 0 Enable bit 30" "Disabled,Enabled" bitfld.long 0x04 29. " [29] ,Interrupt 0 Enable bit 29" "Disabled,Enabled" bitfld.long 0x04 28. " [28] ,Interrupt 0 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x04 27. " [27] ,Interrupt 0 Enable bit 27" "Disabled,Enabled" bitfld.long 0x04 26. " [26] ,Interrupt 0 Enable bit 26" "Disabled,Enabled" bitfld.long 0x04 25. " [25] ,Interrupt 0 Enable bit 25" "Disabled,Enabled" bitfld.long 0x04 24. " [24] ,Interrupt 0 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x04 23. " [23] ,Interrupt 0 Enable bit 23" "Disabled,Enabled" bitfld.long 0x04 22. " [22] ,Interrupt 0 Enable bit 22" "Disabled,Enabled" bitfld.long 0x04 21. " [21] ,Interrupt 0 Enable bit 21" "Disabled,Enabled" bitfld.long 0x04 20. " [20] ,Interrupt 0 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x04 19. " [19] ,Interrupt 0 Enable bit 19" "Disabled,Enabled" bitfld.long 0x04 18. " [18] ,Interrupt 0 Enable bit 18" "Disabled,Enabled" bitfld.long 0x04 17. " [17] ,Interrupt 0 Enable bit 17" "Disabled,Enabled" bitfld.long 0x04 16. " [16] ,Interrupt 0 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x04 15. " [15] ,Interrupt 0 Enable bit 15" "Disabled,Enabled" bitfld.long 0x04 14. " [14] ,Interrupt 0 Enable bit 14" "Disabled,Enabled" bitfld.long 0x04 13. " [13] ,Interrupt 0 Enable bit 13" "Disabled,Enabled" bitfld.long 0x04 12. " [12] ,Interrupt 0 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x04 11. " [11] ,Interrupt 0 Enable bit 11" "Disabled,Enabled" bitfld.long 0x04 10. " [10] ,Interrupt 0 Enable bit 10" "Disabled,Enabled" bitfld.long 0x04 9. " [9] ,Interrupt 0 Enable bit 9" "Disabled,Enabled" bitfld.long 0x04 8. " [8] ,Interrupt 0 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x04 7. " [7] ,Interrupt 0 Enable bit 7" "Disabled,Enabled" bitfld.long 0x04 6. " [6] ,Interrupt 0 Enable bit 6" "Disabled,Enabled" bitfld.long 0x04 5. " [5] ,Interrupt 0 Enable bit 5" "Disabled,Enabled" bitfld.long 0x04 4. " [4] ,Interrupt 0 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x04 3. " [3] ,Interrupt 0 Enable bit 3" "Disabled,Enabled" bitfld.long 0x04 2. " [2] ,Interrupt 0 Enable bit 2" "Disabled,Enabled" bitfld.long 0x04 1. " [1] ,Interrupt 0 Enable bit 1" "Disabled,Enabled" bitfld.long 0x04 0. " [0] ,Interrupt 0 Enable bit 0" "Disabled,Enabled" line.long 0x08 "INT0ENABLE2,Interrupt Enable Register 2 for interrupts bits" bitfld.long 0x08 7. " INT0ENABLE2_[7] ,Interrupt 0 Enable bit 7" "Disabled,Enabled" bitfld.long 0x08 6. " [6] ,Interrupt 0 Enable bit 6" "Disabled,Enabled" bitfld.long 0x08 5. " [5] ,Interrupt 0 Enable bit 5" "Disabled,Enabled" bitfld.long 0x08 4. " [4] ,Interrupt 0 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x08 3. " [3] ,Interrupt 0 Enable bit 3" "Disabled,Enabled" bitfld.long 0x08 2. " [2] ,Interrupt 0 Enable bit 2" "Disabled,Enabled" bitfld.long 0x08 1. " [1] ,Interrupt 0 Enable bit 1" "Disabled,Enabled" bitfld.long 0x08 0. " [0] ,Interrupt 0 Enable bit 0" "Disabled,Enabled" textline "" line.long 0x0C "INT1ENABLE0,Interrupt Enable Register 0 for interrupts bits" bitfld.long 0x0C 31. " INT1ENABLE0_[31] ,Interrupt 1 Enable bit 31" "Disabled,Enabled" bitfld.long 0x0C 30. " [30] ,Interrupt 1 Enable bit 30" "Disabled,Enabled" bitfld.long 0x0C 29. " [29] ,Interrupt 1 Enable bit 29" "Disabled,Enabled" bitfld.long 0x0C 28. " [28] ,Interrupt 1 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x0C 27. " [27] ,Interrupt 1 Enable bit 27" "Disabled,Enabled" bitfld.long 0x0C 26. " [26] ,Interrupt 1 Enable bit 26" "Disabled,Enabled" bitfld.long 0x0C 25. " [25] ,Interrupt 1 Enable bit 25" "Disabled,Enabled" bitfld.long 0x0C 24. " [24] ,Interrupt 1 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x0C 23. " [23] ,Interrupt 1 Enable bit 23" "Disabled,Enabled" bitfld.long 0x0C 22. " [22] ,Interrupt 1 Enable bit 22" "Disabled,Enabled" bitfld.long 0x0C 21. " [21] ,Interrupt 1 Enable bit 21" "Disabled,Enabled" bitfld.long 0x0C 20. " [20] ,Interrupt 1 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x0C 19. " [19] ,Interrupt 1 Enable bit 19" "Disabled,Enabled" bitfld.long 0x0C 18. " [18] ,Interrupt 1 Enable bit 18" "Disabled,Enabled" bitfld.long 0x0C 17. " [17] ,Interrupt 1 Enable bit 17" "Disabled,Enabled" bitfld.long 0x0C 16. " [16] ,Interrupt 1 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x0C 15. " [15] ,Interrupt 1 Enable bit 15" "Disabled,Enabled" bitfld.long 0x0C 14. " [14] ,Interrupt 1 Enable bit 14" "Disabled,Enabled" bitfld.long 0x0C 13. " [13] ,Interrupt 1 Enable bit 13" "Disabled,Enabled" bitfld.long 0x0C 12. " [12] ,Interrupt 1 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x0C 11. " [11] ,Interrupt 1 Enable bit 11" "Disabled,Enabled" bitfld.long 0x0C 10. " [10] ,Interrupt 1 Enable bit 10" "Disabled,Enabled" bitfld.long 0x0C 9. " [9] ,Interrupt 1 Enable bit 9" "Disabled,Enabled" bitfld.long 0x0C 8. " [8] ,Interrupt 1 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x0C 7. " [7] ,Interrupt 1 Enable bit 7" "Disabled,Enabled" bitfld.long 0x0C 6. " [6] ,Interrupt 1 Enable bit 6" "Disabled,Enabled" bitfld.long 0x0C 5. " [5] ,Interrupt 1 Enable bit 5" "Disabled,Enabled" bitfld.long 0x0C 4. " [4] ,Interrupt 1 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x0C 3. " [3] ,Interrupt 1 Enable bit 3" "Disabled,Enabled" bitfld.long 0x0C 2. " [2] ,Interrupt 1 Enable bit 2" "Disabled,Enabled" bitfld.long 0x0C 1. " [1] ,Interrupt 1 Enable bit 1" "Disabled,Enabled" bitfld.long 0x0C 0. " [0] ,Interrupt 1 Enable bit 0" "Disabled,Enabled" line.long 0x10 "INT1ENABLE1,Interrupt Enable Register 1 for interrupts bits" bitfld.long 0x10 31. " INT1ENABLE1_[31] ,Interrupt 1 Enable bit 31" "Disabled,Enabled" bitfld.long 0x10 30. " [30] ,Interrupt 1 Enable bit 30" "Disabled,Enabled" bitfld.long 0x10 29. " [29] ,Interrupt 1 Enable bit 29" "Disabled,Enabled" bitfld.long 0x10 28. " [28] ,Interrupt 1 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x10 27. " [27] ,Interrupt 1 Enable bit 27" "Disabled,Enabled" bitfld.long 0x10 26. " [26] ,Interrupt 1 Enable bit 26" "Disabled,Enabled" bitfld.long 0x10 25. " [25] ,Interrupt 1 Enable bit 25" "Disabled,Enabled" bitfld.long 0x10 24. " [24] ,Interrupt 1 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x10 23. " [23] ,Interrupt 1 Enable bit 23" "Disabled,Enabled" bitfld.long 0x10 22. " [22] ,Interrupt 1 Enable bit 22" "Disabled,Enabled" bitfld.long 0x10 21. " [21] ,Interrupt 1 Enable bit 21" "Disabled,Enabled" bitfld.long 0x10 20. " [20] ,Interrupt 1 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x10 19. " [19] ,Interrupt 1 Enable bit 19" "Disabled,Enabled" bitfld.long 0x10 18. " [18] ,Interrupt 1 Enable bit 18" "Disabled,Enabled" bitfld.long 0x10 17. " [17] ,Interrupt 1 Enable bit 17" "Disabled,Enabled" bitfld.long 0x10 16. " [16] ,Interrupt 1 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x10 15. " [15] ,Interrupt 1 Enable bit 15" "Disabled,Enabled" bitfld.long 0x10 14. " [14] ,Interrupt 1 Enable bit 14" "Disabled,Enabled" bitfld.long 0x10 13. " [13] ,Interrupt 1 Enable bit 13" "Disabled,Enabled" bitfld.long 0x10 12. " [12] ,Interrupt 1 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x10 11. " [11] ,Interrupt 1 Enable bit 11" "Disabled,Enabled" bitfld.long 0x10 10. " [10] ,Interrupt 1 Enable bit 10" "Disabled,Enabled" bitfld.long 0x10 9. " [9] ,Interrupt 1 Enable bit 9" "Disabled,Enabled" bitfld.long 0x10 8. " [8] ,Interrupt 1 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x10 7. " [7] ,Interrupt 1 Enable bit 7" "Disabled,Enabled" bitfld.long 0x10 6. " [6] ,Interrupt 1 Enable bit 6" "Disabled,Enabled" bitfld.long 0x10 5. " [5] ,Interrupt 1 Enable bit 5" "Disabled,Enabled" bitfld.long 0x10 4. " [4] ,Interrupt 1 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x10 3. " [3] ,Interrupt 1 Enable bit 3" "Disabled,Enabled" bitfld.long 0x10 2. " [2] ,Interrupt 1 Enable bit 2" "Disabled,Enabled" bitfld.long 0x10 1. " [1] ,Interrupt 1 Enable bit 1" "Disabled,Enabled" bitfld.long 0x10 0. " [0] ,Interrupt 1 Enable bit 0" "Disabled,Enabled" line.long 0x14 "INT1ENABLE2,Interrupt Enable Register 2 for interrupts bits" bitfld.long 0x14 7. " INT1ENABLE2_[7] ,Interrupt 1 Enable bit 7" "Disabled,Enabled" bitfld.long 0x14 6. " [6] ,Interrupt 1 Enable bit 6" "Disabled,Enabled" bitfld.long 0x14 5. " [5] ,Interrupt 1 Enable bit 5" "Disabled,Enabled" bitfld.long 0x14 4. " [4] ,Interrupt 1 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x14 3. " [3] ,Interrupt 1 Enable bit 3" "Disabled,Enabled" bitfld.long 0x14 2. " [2] ,Interrupt 1 Enable bit 2" "Disabled,Enabled" bitfld.long 0x14 1. " [1] ,Interrupt 1 Enable bit 1" "Disabled,Enabled" bitfld.long 0x14 0. " [0] ,Interrupt 1 Enable bit 0" "Disabled,Enabled" textline "" line.long 0x18 "INTCLEAR0,Interrupt Clear Register 0 for interrupt bits" eventfld.long 0x18 31. " INTCLEAR0_[31] ,Interrupt Clear bit 31" "Not clear,Clear" eventfld.long 0x18 30. " [30] ,Interrupt Clear bit 30" "Not clear,Clear" eventfld.long 0x18 29. " [29] ,Interrupt Clear bit 29" "Not clear,Clear" eventfld.long 0x18 28. " [28] ,Interrupt Clear bit 28" "Not clear,Clear" textline " " eventfld.long 0x18 27. " [27] ,Interrupt Clear bit 27" "Not clear,Clear" eventfld.long 0x18 26. " [26] ,Interrupt Clear bit 26" "Not clear,Clear" eventfld.long 0x18 25. " [25] ,Interrupt Clear bit 25" "Not clear,Clear" eventfld.long 0x18 24. " [24] ,Interrupt Clear bit 24" "Not clear,Clear" textline " " eventfld.long 0x18 23. " [23] ,Interrupt Clear bit 23" "Not clear,Clear" eventfld.long 0x18 22. " [22] ,Interrupt Clear bit 22" "Not clear,Clear" eventfld.long 0x18 21. " [21] ,Interrupt Clear bit 21" "Not clear,Clear" eventfld.long 0x18 20. " [20] ,Interrupt Clear bit 20" "Not clear,Clear" textline " " eventfld.long 0x18 19. " [19] ,Interrupt Clear bit 19" "Not clear,Clear" eventfld.long 0x18 18. " [18] ,Interrupt Clear bit 18" "Not clear,Clear" eventfld.long 0x18 17. " [17] ,Interrupt Clear bit 17" "Not clear,Clear" eventfld.long 0x18 16. " [16] ,Interrupt Clear bit 16" "Not clear,Clear" textline " " eventfld.long 0x18 15. " [15] ,Interrupt Clear bit 15" "Not clear,Clear" eventfld.long 0x18 14. " [14] ,Interrupt Clear bit 14" "Not clear,Clear" eventfld.long 0x18 13. " [13] ,Interrupt Clear bit 13" "Not clear,Clear" eventfld.long 0x18 12. " [12] ,Interrupt Clear bit 12" "Not clear,Clear" textline " " eventfld.long 0x18 11. " [11] ,Interrupt Clear bit 11" "Not clear,Clear" eventfld.long 0x18 10. " [10] ,Interrupt Clear bit 10" "Not clear,Clear" eventfld.long 0x18 9. " [9] ,Interrupt Clear bit 9" "Not clear,Clear" eventfld.long 0x18 8. " [8] ,Interrupt Clear bit 8" "Not clear,Clear" textline " " eventfld.long 0x18 7. " [7] ,Interrupt Clear bit 7" "Not clear,Clear" eventfld.long 0x18 6. " [6] ,Interrupt Clear bit 6" "Not clear,Clear" eventfld.long 0x18 5. " [5] ,Interrupt Clear bit 5" "Not clear,Clear" eventfld.long 0x18 4. " [4] ,Interrupt Clear bit 4" "Not clear,Clear" textline " " eventfld.long 0x18 3. " [3] ,Interrupt Clear bit 3" "Not clear,Clear" eventfld.long 0x18 2. " [2] ,Interrupt Clear bit 2" "Not clear,Clear" eventfld.long 0x18 1. " [1] ,Interrupt Clear bit 1" "Not clear,Clear" eventfld.long 0x18 0. " [0] ,Interrupt Clear bit 0" "Not clear,Clear" line.long 0x1C "INTCLEAR1,Interrupt Clear Register 1 for interrupt bits" eventfld.long 0x1C 31. " INTCLEAR1_[31] ,Interrupt Clear bit 31" "Not clear,Clear" eventfld.long 0x1C 30. " [30] ,Interrupt Clear bit 30" "Not clear,Clear" eventfld.long 0x1C 29. " [29] ,Interrupt Clear bit 29" "Not clear,Clear" eventfld.long 0x1C 28. " [28] ,Interrupt Clear bit 28" "Not clear,Clear" textline " " eventfld.long 0x1C 27. " [27] ,Interrupt Clear bit 27" "Not clear,Clear" eventfld.long 0x1C 26. " [26] ,Interrupt Clear bit 26" "Not clear,Clear" eventfld.long 0x1C 25. " [25] ,Interrupt Clear bit 25" "Not clear,Clear" eventfld.long 0x1C 24. " [24] ,Interrupt Clear bit 24" "Not clear,Clear" textline " " eventfld.long 0x1C 23. " [23] ,Interrupt Clear bit 23" "Not clear,Clear" eventfld.long 0x1C 22. " [22] ,Interrupt Clear bit 22" "Not clear,Clear" eventfld.long 0x1C 21. " [21] ,Interrupt Clear bit 21" "Not clear,Clear" eventfld.long 0x1C 20. " [20] ,Interrupt Clear bit 20" "Not clear,Clear" textline " " eventfld.long 0x1C 19. " [19] ,Interrupt Clear bit 19" "Not clear,Clear" eventfld.long 0x1C 18. " [18] ,Interrupt Clear bit 18" "Not clear,Clear" eventfld.long 0x1C 17. " [17] ,Interrupt Clear bit 17" "Not clear,Clear" eventfld.long 0x1C 16. " [16] ,Interrupt Clear bit 16" "Not clear,Clear" textline " " eventfld.long 0x1C 15. " [15] ,Interrupt Clear bit 15" "Not clear,Clear" eventfld.long 0x1C 14. " [14] ,Interrupt Clear bit 14" "Not clear,Clear" eventfld.long 0x1C 13. " [13] ,Interrupt Clear bit 13" "Not clear,Clear" eventfld.long 0x1C 12. " [12] ,Interrupt Clear bit 12" "Not clear,Clear" textline " " eventfld.long 0x1C 11. " [11] ,Interrupt Clear bit 11" "Not clear,Clear" eventfld.long 0x1C 10. " [10] ,Interrupt Clear bit 10" "Not clear,Clear" eventfld.long 0x1C 9. " [9] ,Interrupt Clear bit 9" "Not clear,Clear" eventfld.long 0x1C 8. " [8] ,Interrupt Clear bit 8" "Not clear,Clear" textline " " eventfld.long 0x1C 7. " [7] ,Interrupt Clear bit 7" "Not clear,Clear" eventfld.long 0x1C 6. " [6] ,Interrupt Clear bit 6" "Not clear,Clear" eventfld.long 0x1C 5. " [5] ,Interrupt Clear bit 5" "Not clear,Clear" eventfld.long 0x1C 4. " [4] ,Interrupt Clear bit 4" "Not clear,Clear" textline " " eventfld.long 0x1C 3. " [3] ,Interrupt Clear bit 3" "Not clear,Clear" eventfld.long 0x1C 2. " [2] ,Interrupt Clear bit 2" "Not clear,Clear" eventfld.long 0x1C 1. " [1] ,Interrupt Clear bit 1" "Not clear,Clear" eventfld.long 0x1C 0. " [0] ,Interrupt Clear bit 0" "Not clear,Clear" line.long 0x20 "INTCLEAR2,Interrupt Clear Register 2 for interrupt bits" eventfld.long 0x20 7. " INTCLEAR2_[7] ,Interrupt Clear bit 7" "Not clear,Clear" eventfld.long 0x20 6. " [6] ,Interrupt Clear bit 6" "Not clear,Clear" eventfld.long 0x20 5. " [5] ,Interrupt Clear bit 5" "Not clear,Clear" eventfld.long 0x20 4. " [4] ,Interrupt Clear bit 4" "Not clear,Clear" textline " " eventfld.long 0x20 3. " [3] ,Interrupt Clear bit 3" "Not clear,Clear" eventfld.long 0x20 2. " [2] ,Interrupt Clear bit 2" "Not clear,Clear" eventfld.long 0x20 1. " [1] ,Interrupt Clear bit 1" "Not clear,Clear" eventfld.long 0x20 0. " [0] ,Interrupt Clear bit 0" "Not clear,Clear" textline "" line.long 0x24 "INTPRESET0,Interrupt Preset Register 1 for interrupt bits" eventfld.long 0x24 31. " INTPRESET0_[31] ,Interrupt Preset bit 31" "Not interrupt,Interrupt" eventfld.long 0x24 30. " [30] ,Interrupt Preset bit 30" "Not interrupt,Interrupt" eventfld.long 0x24 29. " [29] ,Interrupt Preset bit 29" "Not interrupt,Interrupt" eventfld.long 0x24 28. " [28] ,Interrupt Preset bit 28" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 27. " [27] ,Interrupt Preset bit 27" "Not interrupt,Interrupt" eventfld.long 0x24 26. " [26] ,Interrupt Preset bit 26" "Not interrupt,Interrupt" eventfld.long 0x24 25. " [25] ,Interrupt Preset bit 25" "Not interrupt,Interrupt" eventfld.long 0x24 24. " [24] ,Interrupt Preset bit 24" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 23. " [23] ,Interrupt Preset bit 23" "Not interrupt,Interrupt" eventfld.long 0x24 22. " [22] ,Interrupt Preset bit 22" "Not interrupt,Interrupt" eventfld.long 0x24 21. " [21] ,Interrupt Preset bit 21" "Not interrupt,Interrupt" eventfld.long 0x24 20. " [20] ,Interrupt Preset bit 20" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 19. " [19] ,Interrupt Preset bit 19" "Not interrupt,Interrupt" eventfld.long 0x24 18. " [18] ,Interrupt Preset bit 18" "Not interrupt,Interrupt" eventfld.long 0x24 17. " [17] ,Interrupt Preset bit 17" "Not interrupt,Interrupt" eventfld.long 0x24 16. " [16] ,Interrupt Preset bit 16" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 15. " [15] ,Interrupt Preset bit 15" "Not interrupt,Interrupt" eventfld.long 0x24 14. " [14] ,Interrupt Preset bit 14" "Not interrupt,Interrupt" eventfld.long 0x24 13. " [13] ,Interrupt Preset bit 13" "Not interrupt,Interrupt" eventfld.long 0x24 12. " [12] ,Interrupt Preset bit 12" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 11. " [11] ,Interrupt Preset bit 11" "Not interrupt,Interrupt" eventfld.long 0x24 10. " [10] ,Interrupt Preset bit 10" "Not interrupt,Interrupt" eventfld.long 0x24 9. " [9] ,Interrupt Preset bit 9" "Not interrupt,Interrupt" eventfld.long 0x24 8. " [8] ,Interrupt Preset bit 8" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 7. " [7] ,Interrupt Preset bit 7" "Not interrupt,Interrupt" eventfld.long 0x24 6. " [6] ,Interrupt Preset bit 6" "Not interrupt,Interrupt" eventfld.long 0x24 5. " [5] ,Interrupt Preset bit 5" "Not interrupt,Interrupt" eventfld.long 0x24 4. " [4] ,Interrupt Preset bit 4" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 3. " [3] ,Interrupt Preset bit 3" "Not interrupt,Interrupt" eventfld.long 0x24 2. " [2] ,Interrupt Preset bit 2" "Not interrupt,Interrupt" eventfld.long 0x24 1. " [1] ,Interrupt Preset bit 1" "Not interrupt,Interrupt" eventfld.long 0x24 0. " [0] ,Interrupt Preset bit 0" "Not interrupt,Interrupt" line.long 0x28 "INTPRESET1,Interrupt Preset Register 1 for interrupt bits" eventfld.long 0x28 31. " INTPRESET1_[31] ,Interrupt Preset bit 31" "Not interrupt,Interrupt" eventfld.long 0x28 30. " [30] ,Interrupt Preset bit 30" "Not interrupt,Interrupt" eventfld.long 0x28 29. " [29] ,Interrupt Preset bit 29" "Not interrupt,Interrupt" eventfld.long 0x28 28. " [28] ,Interrupt Preset bit 28" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 27. " [27] ,Interrupt Preset bit 27" "Not interrupt,Interrupt" eventfld.long 0x28 26. " [26] ,Interrupt Preset bit 26" "Not interrupt,Interrupt" eventfld.long 0x28 25. " [25] ,Interrupt Preset bit 25" "Not interrupt,Interrupt" eventfld.long 0x28 24. " [24] ,Interrupt Preset bit 24" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 23. " [23] ,Interrupt Preset bit 23" "Not interrupt,Interrupt" eventfld.long 0x28 22. " [22] ,Interrupt Preset bit 22" "Not interrupt,Interrupt" eventfld.long 0x28 21. " [21] ,Interrupt Preset bit 21" "Not interrupt,Interrupt" eventfld.long 0x28 20. " [20] ,Interrupt Preset bit 20" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 19. " [19] ,Interrupt Preset bit 19" "Not interrupt,Interrupt" eventfld.long 0x28 18. " [18] ,Interrupt Preset bit 18" "Not interrupt,Interrupt" eventfld.long 0x28 17. " [17] ,Interrupt Preset bit 17" "Not interrupt,Interrupt" eventfld.long 0x28 16. " [16] ,Interrupt Preset bit 16" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 15. " [15] ,Interrupt Preset bit 15" "Not interrupt,Interrupt" eventfld.long 0x28 14. " [14] ,Interrupt Preset bit 14" "Not interrupt,Interrupt" eventfld.long 0x28 13. " [13] ,Interrupt Preset bit 13" "Not interrupt,Interrupt" eventfld.long 0x28 12. " [12] ,Interrupt Preset bit 12" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 11. " [11] ,Interrupt Preset bit 11" "Not interrupt,Interrupt" eventfld.long 0x28 10. " [10] ,Interrupt Preset bit 10" "Not interrupt,Interrupt" eventfld.long 0x28 9. " [9] ,Interrupt Preset bit 9" "Not interrupt,Interrupt" eventfld.long 0x28 8. " [8] ,Interrupt Preset bit 8" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 7. " [7] ,Interrupt Preset bit 7" "Not interrupt,Interrupt" eventfld.long 0x28 6. " [6] ,Interrupt Preset bit 6" "Not interrupt,Interrupt" eventfld.long 0x28 5. " [5] ,Interrupt Preset bit 5" "Not interrupt,Interrupt" eventfld.long 0x28 4. " [4] ,Interrupt Preset bit 4" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 3. " [3] ,Interrupt Preset bit 3" "Not interrupt,Interrupt" eventfld.long 0x28 2. " [2] ,Interrupt Preset bit 2" "Not interrupt,Interrupt" eventfld.long 0x28 1. " [1] ,Interrupt Preset bit 1" "Not interrupt,Interrupt" eventfld.long 0x28 0. " [0] ,Interrupt Preset bit 0" "Not interrupt,Interrupt" line.long 0x2C "INTPRESET2,Interrupt Preset Register 2 for interrupt bits" eventfld.long 0x2C 7. " INTPRESET2_[7] ,Interrupt Preset bit 7" "Not interrupt,Interrupt" eventfld.long 0x2C 6. " [6] ,Interrupt Preset bit 6" "Not interrupt,Interrupt" eventfld.long 0x2C 5. " [5] ,Interrupt Preset bit 5" "Not interrupt,Interrupt" eventfld.long 0x2C 4. " [4] ,Interrupt Preset bit 4" "Not interrupt,Interrupt" textline " " eventfld.long 0x2C 3. " [3] ,Interrupt Preset bit 3" "Not interrupt,Interrupt" eventfld.long 0x2C 2. " [2] ,Interrupt Preset bit 2" "Not interrupt,Interrupt" eventfld.long 0x2C 1. " [1] ,Interrupt Preset bit 1" "Not interrupt,Interrupt" eventfld.long 0x2C 0. " [0] ,Interrupt Preset bit 0" "Not interrupt,Interrupt" tree.end width 15. group.long 0x400++0x03 line.long 0x00 "FIFO,FIFO" button "FIFO" "d (ad:0x3A020000+0x400)--(ad:0x3A020000+0x4FF) /long" group.long 0x500++0x03 line.long 0x00 "CONTROL,Message Buffer Control" bitfld.long 0x00 31. " BLOCK_ON_FATAL ,Suppress pending signal when fatal error was detected" "No error,Error" bitfld.long 0x00 2. " R1BUF_BACKPRESSURE_ENABLE ,Enable backpressure when read buffer 1 is running full" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " R0BUF_BACKPRESSURE_ENABLE ,Enable backpressure when read buffer 0 is running full" "Disabled,Enabled" rgroup.long 0x504++0x03 line.long 0x00 "STATUS,Message Buffer Status" bitfld.long 0x00 6. " WDG_TIMEOUT ,Watchdog timeout" "Not timeout,Timeout" bitfld.long 0x00 5. " WRBUF_EMPTY ,Write buffer is empty" "Not empty,Empty" textline " " bitfld.long 0x00 4. " WRBUF_FULL ,Write buffer is full" "Not full,Full" bitfld.long 0x00 3. " R1BUF_EMPTY ,Read buffer 1 is empty" "Not empty,Empty" textline " " bitfld.long 0x00 2. " R1BUF_FULL ,Read buffer 1 is full" "Not full,Full" bitfld.long 0x00 1. " R0BUF_EMPTY ,Read buffer 0 is empty" "Not empty,Empty" textline " " bitfld.long 0x00 0. " R0BUF_FULL ,Read buffer 0 is full" "Not full,Full" group.long 0x508++0x0B line.long 0x00 "CLEAR,Message Buffer Clear" eventfld.long 0x00 2. " R1BUF_CLEAR ,Writing a '1' clears read buffer 1" "Not clear,Clear" eventfld.long 0x00 1. " R0BUF_CLEAR ,Writing a '1' clears read buffer 0" "Not clear,Clear" textline " " eventfld.long 0x00 0. " WRBUF_CLEAR ,Writing a '1' clears write buffer" "Not clear,Clear" line.long 0x04 "DMA_CONTROL,DMA Control" bitfld.long 0x04 24.--25. " DMA2_MODE ,Dma2 mode" "Previous,Local,Both," bitfld.long 0x04 20.--21. " DMA1_MODE ,Dma1 mode" "Previous,Local,Both," textline " " bitfld.long 0x04 16.--17. " DMA0_MODE ,Dma0 mode" "Previous,Local,Both," bitfld.long 0x04 10. " R1BUF_DMA_ENABLE ,Enable DMA for read buffer 1" "Disabled,Enabled" textline " " bitfld.long 0x04 6. " R0BUF_DMA_ENABLE ,Enable DMA for read buffer 0" "Disabled,Enabled" bitfld.long 0x04 4.--5. " R0BUF_DMA_PORT ,DMA port number for read buffer 0" "0,1,2,3" textline " " bitfld.long 0x04 2. " WRBUF_DMA_ENABLE ,Enable DMA for write buffer" "Disabled,Enabled" bitfld.long 0x04 0.--1. " WRBUF_DMA_PORT ,DMA port number for write buffer" "0,1,2,3" line.long 0x08 "WATCHDOG_LOAD,Watchdog counter preset value" textline "" width 39. group.long 0x600++0x0B line.long 0x00 "RX0_I2C_OUTBOUND_JOB_SPEC_STATUS,RX0_I2C_Outbound_Job_Spec_Status" eventfld.long 0x00 31. " RX0_I2C_OUTBOUND_JOB_SPEC_CLEAR ,RX0_I2C_Outbound_Job_Spec_Clear" "Not clear,Clear" textline " " rbitfld.long 0x00 0. " RX0_I2C_OUTBOUND_JOB_SPEC_BUSY ,RX0_I2C_Outbound_Job_Spec_Busy" "Not busy,Busy" line.long 0x04 "RX0_I2C_OUTBOUND_JOB_SPEC_DATA_LOW,RX0_I2C_Outbound_Job_Spec_Data_Low" line.long 0x08 "RX0_I2C_OUTBOUND_JOB_SPEC_DATA_HIGH,RX0_I2C_Outbound_Job_Spec_Data_High" rgroup.long 0x60C++0x0B line.long 0x00 "RX0_I2C_INBOUND_JOB_SPEC_STATUS,RX0_I2C_Inbound_Job_Spec_Status" bitfld.long 0x00 0. " RX0_I2C_INBOUND_JOB_SPEC_VALID ,RX0_I2C_Inbound_Job_Spec_Valid" "No,Yes" line.long 0x04 "RX0_I2C_INBOUND_JOB_SPEC_DATA_LOW,RX0_I2C_Inbound_Job_Spec_Data_Low" line.long 0x08 "RX0_I2C_INBOUND_JOB_SPEC_DATA_HIGH,RX0_I2C_Inbound_Job_Spec_Data_High" group.long 0x618++0x0B line.long 0x00 "RX0_I2C_INBOUND_JOB_SPEC_ERROR,RX0_I2C_Inbound_Job_Spec_Error" bitfld.long 0x00 31. " RX0_I2C_INBOUND_JOB_SPEC_ERROR ,RX0_I2C_Inbound_Job_Spec_Error" "No error,Error" line.long 0x04 "RX0_I2C_OUTBOUND_STATUS,RX0_I2C_Outbound_Status" eventfld.long 0x04 31. " RX0_I2C_OUTBOUND_STATUS_CLEAR ,RX0_I2C_Outbound_Status_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX0_I2C_OUTBOUND_STATUS_BUSY ,RX0_I2C_Outbound_Status_Busy" "Not busy,Busy" line.long 0x08 "RX0_I2C_OUTBOUND_STATUS_DATA,RX0_I2C_Outbound_Status_Data" bitfld.long 0x08 3. " RX0_I2C_OUTBOUND_STATUS_ALOST_DETECTED ,RX0_I2C_Outbound_Status_Alost_Detected" "Not detected,Detected" textline " " bitfld.long 0x08 2. " RX0_I2C_OUTBOUND_STATUS_NACK_DETECTED ,RX0_I2C_Outbound_Status_Nack_Detected" "Not detected,Detected" textline " " bitfld.long 0x08 1. " RX0_I2C_OUTBOUND_STATUS_JOB_CACC ,RX0_I2C_Outbound_Status_Job_Cacc" "0,1" textline " " bitfld.long 0x08 0. " RX0_I2C_OUTBOUND_STATUS_JOB_DONE ,RX0_I2C_Outbound_Status_Job_Done" "0,1" rgroup.long 0x624++0x03 line.long 0x00 "RX0_I2C_INBOUND_STATUS,RX0_I2C_Inbound_Status" bitfld.long 0x00 0. " RX0_I2C_INBOUND_STATUS_VALID ,RX0_I2C_Inbound_Status_Valid" "No,Yes" group.long 0x628++0x0B line.long 0x00 "RX0_I2C_INBOUND_STATUS_DATA,RX0_I2C_Inbound_Status_Data" bitfld.long 0x00 31. " RX0_I2C_INBOUND_STATUS_ERROR ,RX0_I2C_Inbound_Status_Error" "No error,Error" textline " " rbitfld.long 0x00 3. " RX0_I2C_INBOUND_STATUS_ALOST_DETECTED ,RX0_I2C_Inbound_Status_Alost_detected" "Not detected,Detected" textline " " rbitfld.long 0x00 2. " RX0_I2C_INBOUND_STATUS_NACK_DETECTED ,RX0_I2C_Inbound_Status_Nack_detected" "Not detected,Detected" textline " " rbitfld.long 0x00 1. " RX0_I2C_INBOUND_STATUS_JOB_CACC ,RX0_I2C_Inbound_Status_Job_cacc" "0,1" textline " " rbitfld.long 0x00 0. " RX0_I2C_INBOUND_STATUS_JOB_DONE ,RX0_I2C_Inbound_Status_Job_done" "0,1" line.long 0x04 "RX0_I2C_OUTBOUND_READ_RESPONSE_STATUS,RX0_I2C_Outbound_Read_Response_Status" eventfld.long 0x04 31. " RX0_I2C_OUTBOUND_READ_RESPONSE_CLEAR ,RX0_I2C_Outbound_Read_Response_Clear" "Not clear,Clear" textline " " bitfld.long 0x04 0. " RX0_I2C_OUTBOUND_READ_RESPONSE_BUSY ,RX0_I2C_Outbound_Read_Response_Busy" "Not busy,Busy" line.long 0x08 "RX0_I2C_OUTBOUND_READ_RESPONSE_DATA,RX0_I2C_Outbound_Read_Response_Data" hexmask.long.byte 0x08 0.--7. 1. " RX0_I2C_OUTBOUND_READ_RESPONSE_DATA ,RX0_I2C_Outbound_Read_Response_Data" rgroup.long 0x634++0x03 line.long 0x00 "RX0_I2C_INBOUND_READ_RESPONSE_STATUS,RX0_I2C_Inbound_Read_Response_Status" bitfld.long 0x00 0. " RX0_I2C_INBOUND_READ_RESPONSE_VALID ,RX0_I2C_Inbound_Read_Response_Valid" "No,Yes" group.long 0x638++0x0F line.long 0x00 "RX0_I2C_INBOUND_READ_RESPONSE_DATA,RX0_I2C_Inbound_Read_Response_Data" bitfld.long 0x00 31. " RX0_I2C_INBOUND_READ_RESPONSE_ERROR ,RX0_I2C_Inbound_Read_Response_Error" "No error,Error" textline " " rbitfld.long 0x00 8.--10. " RX0_I2C_INBOUND_READ_RESPONSE_DATA_NUM ,RX0_I2C_Inbound_Read_Response_Data_Num" "0,1,2,3,4,5,6,7" textline " " hexmask.long.byte 0x00 0.--7. 1. " RX0_I2C_INBOUND_READ_RESPONSE_DATA ,RX0_I2C_Inbound_Read_Response_Data" line.long 0x04 "RX1_I2C_OUTBOUND_JOB_SPEC_STATUS,RX1_I2C_Outbound_Job_Spec_Status" eventfld.long 0x04 31. " RX1_I2C_OUTBOUND_JOB_SPEC_CLEAR ,RX1_I2C_Outbound_Job_Spec_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX1_I2C_OUTBOUND_JOB_SPEC_BUSY ,RX1_I2C_Outbound_Job_Spec_Busy" "Not busy,Busy" line.long 0x08 "RX1_I2C_OUTBOUND_JOB_SPEC_DATA_LOW,RX1_I2C_Outbound_Job_Spec_Data_Low" line.long 0x0C "RX1_I2C_OUTBOUND_JOB_SPEC_DATA_HIGH,RX1_I2C_Outbound_Job_Spec_Data_High" rgroup.long 0x648++0x0B line.long 0x00 "RX1_I2C_INBOUND_JOB_SPEC_STATUS,RX1_I2C_Inbound_Job_Spec_Status" bitfld.long 0x00 0. " RX1_I2C_INBOUND_JOB_SPEC_VALID ,RX1_I2C_Inbound_Job_Spec_Valid" "No,Yes" line.long 0x04 "RX1_I2C_INBOUND_JOB_SPEC_DATA_LOW,RX1_I2C_Inbound_Job_Spec_Data_Low" line.long 0x08 "RX1_I2C_INBOUND_JOB_SPEC_DATA_HIGH,RX1_I2C_Inbound_Job_Spec_Data_High" group.long 0x654++0x0B line.long 0x00 "RX1_I2C_INBOUND_JOB_SPEC_ERROR,RX1_I2C_Inbound_Job_Spec_Error" bitfld.long 0x00 31. " RX1_I2C_INBOUND_JOB_SPEC_ERROR ,RX1_I2C_Inbound_Job_Spec_Error" "No error,Error" line.long 0x04 "RX1_I2C_OUTBOUND_STATUS,RX1_I2C_Outbound_Status" eventfld.long 0x04 31. " RX1_I2C_OUTBOUND_STATUS_CLEAR ,RX1_I2C_Outbound_Status_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX1_I2C_OUTBOUND_STATUS_BUSY ,RX1_I2C_Outbound_Status_Busy" "Not busy,Busy" line.long 0x08 "RX1_I2C_OUTBOUND_STATUS_DATA,RX1_I2C_Outbound_Status_Data" bitfld.long 0x08 3. " RX1_I2C_OUTBOUND_STATUS_ALOST_DETECTED ,RX1_I2C_Outbound_Status_Alost_Detected" "Not detected,Detected" textline " " bitfld.long 0x08 2. " RX1_I2C_OUTBOUND_STATUS_NACK_DETECTED ,RX1_I2C_Outbound_Status_Nack_Detected" "Not detected,Detected" textline " " bitfld.long 0x08 1. " RX1_I2C_OUTBOUND_STATUS_JOB_CACC ,RX1_I2C_Outbound_Status_Job_Cacc" "0,1" textline " " bitfld.long 0x08 0. " RX1_I2C_OUTBOUND_STATUS_JOB_DONE ,RX1_I2C_Outbound_Status_Job_Done" "0,1" rgroup.long 0x660++0x03 line.long 0x00 "RX1_I2C_INBOUND_STATUS,RX1_I2C_Inbound_Status" bitfld.long 0x00 0. " RX1_I2C_INBOUND_STATUS_VALID ,RX1_I2C_Inbound_Status_Valid" "No,Yes" group.long 0x664++0x0B line.long 0x00 "RX1_I2C_INBOUND_STATUS_DATA,RX1_I2C_Inbound_Status_Data" bitfld.long 0x00 31. " RX1_I2C_INBOUND_STATUS_ERROR ,RX1_I2C_Inbound_Status_Error" "No error,Error" textline " " rbitfld.long 0x00 3. " RX1_I2C_INBOUND_STATUS_ALOST_DETECTED ,RX1_I2C_Inbound_Status_Alost_detected" "Not detected,Detected" textline " " bitfld.long 0x00 2. " RX1_I2C_INBOUND_STATUS_NACK_DETECTED ,RX1_I2C_Inbound_Status_Nack_detected" "Not detected,Detected" textline " " rbitfld.long 0x00 1. " RX1_I2C_INBOUND_STATUS_JOB_CACC ,RX1_I2C_Inbound_Status_Job_cacc" "0,1" textline " " bitfld.long 0x00 0. " RX1_I2C_INBOUND_STATUS_JOB_DONE ,RX1_I2C_Inbound_Status_Job_done" "0,1" line.long 0x04 "RX1_I2C_OUTBOUND_READ_RESPONSE_STATUS,RX1_I2C_Outbound_Read_Response_Status" eventfld.long 0x04 31. " RX1_I2C_OUTBOUND_READ_RESPONSE_CLEAR ,RX1_I2C_Outbound_Read_Response_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX1_I2C_OUTBOUND_READ_RESPONSE_BUSY ,RX1_I2C_Outbound_Read_Response_Busy" "Not busy,Busy" line.long 0x08 "RX1_I2C_OUTBOUND_READ_RESPONSE_DATA,RX1_I2C_Outbound_Read_Response_Data" hexmask.long.byte 0x08 0.--7. 1. " RX1_I2C_OUTBOUND_READ_RESPONSE_DATA ,RX1_I2C_Outbound_Read_Response_Data" rgroup.long 0x670++0x03 line.long 0x00 "RX1_I2C_INBOUND_READ_RESPONSE_STATUS,RX1_I2C_Inbound_Read_Response_Status" bitfld.long 0x00 0. " RX1_I2C_INBOUND_READ_RESPONSE_VALID ,RX1_I2C_Inbound_Read_Response_Valid" "No,Yes" group.long 0x674++0x0B line.long 0x00 "RX1_I2C_INBOUND_READ_RESPONSE_DATA,RX1_I2C_Inbound_Read_Response_Data" bitfld.long 0x00 31. " RX1_I2C_INBOUND_READ_RESPONSE_ERROR ,RX1_I2C_Inbound_Read_Response_Error" "No error,Error" textline " " rbitfld.long 0x00 8.--10. " RX1_I2C_INBOUND_READ_RESPONSE_DATA_NUM ,RX1_I2C_Inbound_Read_Response_Data_Num" "0,1,2,3,4,5,6,7" textline " " hexmask.long.byte 0x00 0.--7. 1. " RX1_I2C_INBOUND_READ_RESPONSE_DATA ,RX1_I2C_Inbound_Read_Response_Data" line.long 0x04 "RX0_REMOTE_CONTROLLER_OUTBOUND_STATUS,RX0_Remote_Controller_Outbound_Status" eventfld.long 0x04 31. " RX0_REMOTE_CONTROLLER_OUTBOUND_CLEAR ,RX0_Remote_Controller_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX0_REMOTE_CONTROLLER_OUTBOUND_BUSY ,RX0_Remote_Controller_Outbound_Busy" "Not busy,Busy" line.long 0x08 "RX0_REMOTE_CONTROLLER_OUTBOUND_DATA,RX0_Remote_Controller_Outbound_Data" hexmask.long.byte 0x08 8.--15. 1. " RX0_REMOTE_CONTROLLER_OUTBOUND_DATA ,RX0_Remote_Controller_Outbound_Data" textline " " bitfld.long 0x08 7. " RX0_REMOTE_CONTROLLER_OUTBOUND_RW ,RX0_Remote_Controller_Outbound_RW" "0,1" textline " " hexmask.long.byte 0x08 0.--6. 1. " RX0_REMOTE_CONTROLLER_OUTBOUND_ADDRESS ,RX0_Remote_Controller_Outbound_Address" rgroup.long 0x680++0x03 line.long 0x00 "RX0_REMOTE_CONTROLLER_INBOUND_STATUS,RX0_Remote_Controller_Inbound_Status" bitfld.long 0x00 0. " RX0_REMOTE_CONTROLLER_INBOUND_VALID ,RX0_Remote_Controller_Inbound_Valid" "No,Yes" group.long 0x684++0x03 line.long 0x00 "RX0_REMOTE_CONTROLLER_INBOUND_DATA,RX0_Remote_Controller_Inbound_Data" rbitfld.long 0x00 31. " RX0_REMOTE_CONTROLLER_INBOUND_ERROR ,RX0_Remote_Controller_Inbound_Error" "No error,Error" textline " " hexmask.long.byte 0x00 0.--7. 1. " RX0_REMOTE_CONTROLLER_INBOUND_RESPONSE_DATA ,RX0_Remote_Controller_Inbound_Response_Data" rgroup.long 0x688++0x03 line.long 0x00 "RX0_REMOTE_SERVICE_INBOUND_STATUS,RX0_Remote_Service_Inbound_Status" bitfld.long 0x00 0. " RX0_REMOTE_SERVICE_INBOUND_VALID ,RX0_Remote_Service_Inbound_Valid" "No,Yes" group.long 0x68C++0x1B line.long 0x00 "RX0_REMOTE_SERVICE_INBOUND_DATA,RX0_Remote_Service_Inbound_Data" bitfld.long 0x00 31. " RX0_REMOTE_SERVICE_INBOUND_ERROR ,RX0_Remote_Service_Inbound_Error" "No error,Error" textline " " hexmask.long.byte 0x00 8.--15. 1. " RX0_REMOTE_SERVICE_INBOUND_DATA ,RX0_Remote_Service_Inbound_Data" textline " " bitfld.long 0x00 7. " RX0_REMOTE_SERVICE_INBOUND_RW ,RX0_Remote_Service_Inbound_RW" "0,1" textline " " hexmask.long.byte 0x00 0.--6. 1. " RX0_REMOTE_SERVICE_INBOUND_ADDRESS ,RX0_Remote_Service_Inbound_Address" line.long 0x04 "RX0_REMOTE_SERVICE_OUTBOUND_STATUS,RX0_Remote_Service_Outbound_Status" eventfld.long 0x04 31. " RX0_REMOTE_SERVICE_OUTBOUND_CLEAR ,RX0_Remote_Service_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX0_REMOTE_SERVICE_OUTBOUND_BUSY ,RX0_Remote_Service_Outbound_Busy" "Not busy,Busy" line.long 0x08 "RX0_REMOTE_SERVICE_OUTBOUND_DATA,RX0_Remote_Service_Outbound_Data" hexmask.long.byte 0x08 0.--7. 1. " RX0_REMOTE_SERVICE_OUTBOUND_READ_RESPONSE_DATA ,RX0_Remote_Service_Outbound_Read_Response_Data" line.long 0x0C "RX0_REMOTE_COMMAND_OUTBOUND_STATUS,RX0_Remote_Command_Outbound_Status" eventfld.long 0x0C 31. " RX0_REMOTE_COMMAND_OUTBOUND_CLEAR ,RX0_Remote_Command_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x0C 0. " RX0_REMOTE_COMMAND_OUTBOUND_BUSY ,RX0_Remote_Command_Outbound_Busy" "Not busy,Busy" line.long 0x10 "RX0_REMOTE_COMMAND_OUTBOUND_DATA,RX0_Remote_Command_Outbound_Data" bitfld.long 0x10 3. " RX0_REMOTE_COMMAND_OUTBOUND_JOB_CANCEL ,RX0_Remote_Command_Outbound_Job_Cancel" "0,1" textline " " bitfld.long 0x10 2. " RX0_REMOTE_COMMAND_OUTBOUND_CLEAR_TICKET_COUNTER ,RX0_Remote_Command_Outbound_Clear_Ticket_Counter" "Not clear,Clear" textline " " bitfld.long 0x10 1. " RX0_REMOTE_COMMAND_OUTBOUND_REALIGN ,RX0_Remote_Command_Outbound_Realign" "No,Yes" textline " " bitfld.long 0x10 0. " RX0_REMOTE_COMMAND_OUTBOUND_SOFT_RESET ,RX0_Remote_Command_Outbound_Soft_Reset" "No reset,Reset" line.long 0x14 "RX1_REMOTE_CONTROLLER_OUTBOUND_STATUS,RX1_Remote_Controller_Outbound_Status" eventfld.long 0x14 31. " RX1_REMOTE_CONTROLLER_OUTBOUND_CLEAR ,RX1_Remote_Controller_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x14 0. " RX1_REMOTE_CONTROLLER_OUTBOUND_BUSY ,RX1_Remote_Controller_Outbound_Busy" "Not busy,Busy" line.long 0x18 "RX1_REMOTE_CONTROLLER_OUTBOUND_DATA,RX1_Remote_Controller_Outbound_Data" hexmask.long.byte 0x18 8.--15. 1. " RX1_REMOTE_CONTROLLER_OUTBOUND_DATA ,RX1_Remote_Controller_Outbound_Data" textline " " bitfld.long 0x18 7. " RX1_REMOTE_CONTROLLER_OUTBOUND_RW ,RX1_Remote_Controller_Outbound_RW" "0,1" textline " " hexmask.long.byte 0x18 0.--6. 1. " RX1_REMOTE_CONTROLLER_OUTBOUND_ADDRESS ,RX1_Remote_Controller_Outbound_Address" rgroup.long 0x6A8++0x03 line.long 0x00 "RX1_REMOTE_CONTROLLER_INBOUND_STATUS,RX1_Remote_Controller_Inbound_Status" bitfld.long 0x00 0. " RX1_REMOTE_CONTROLLER_INBOUND_VALID ,RX1_Remote_Controller_Inbound_Valid" "No,Yes" group.long 0x6AC++0x03 line.long 0x00 "RX1_REMOTE_CONTROLLER_INBOUND_DATA,RX1_Remote_Controller_Inbound_Data" bitfld.long 0x00 31. " RX1_REMOTE_CONTROLLER_INBOUND_ERROR ,RX1_Remote_Controller_Inbound_Error" "No error,Error" textline " " hexmask.long.byte 0x00 0.--7. 1. " RX1_REMOTE_CONTROLLER_INBOUND_RESPONSE_DATA ,RX1_Remote_Controller_Inbound_Response_Data" rgroup.long 0x6B0++0x03 line.long 0x00 "RX1_REMOTE_SERVICE_INBOUND_STATUS,RX1_Remote_Service_Inbound_Status" bitfld.long 0x00 0. " RX1_REMOTE_SERVICE_INBOUND_VALID ,RX1_Remote_Service_Inbound_Valid" "No,Yes" group.long 0x6B4++0x13 line.long 0x00 "RX1_REMOTE_SERVICE_INBOUND_DATA,RX1_Remote_Service_Inbound_Data" bitfld.long 0x00 31. " RX1_REMOTE_SERVICE_INBOUND_ERROR ,RX1_Remote_Service_Inbound_Error" "No error,Error" textline " " hexmask.long.byte 0x00 8.--15. 1. " RX1_REMOTE_SERVICE_INBOUND_DATA ,RX1_Remote_Service_Inbound_Data" textline " " bitfld.long 0x00 7. " RX1_REMOTE_SERVICE_INBOUND_RW ,RX1_Remote_Service_Inbound_RW" "0,1" textline " " hexmask.long.byte 0x00 0.--6. 1. " RX1_REMOTE_SERVICE_INBOUND_ADDRESS ,RX1_Remote_Service_Inbound_Address" line.long 0x04 "RX1_REMOTE_SERVICE_OUTBOUND_STATUS,RX1_Remote_Service_Outbound_Status" eventfld.long 0x04 31. " RX1_REMOTE_SERVICE_OUTBOUND_CLEAR ,RX1_Remote_Service_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX1_REMOTE_SERVICE_OUTBOUND_BUSY ,RX1_Remote_Service_Outbound_Busy" "Not busy,Busy" line.long 0x08 "RX1_REMOTE_SERVICE_OUTBOUND_DATA,RX1_Remote_Service_Outbound_Data" hexmask.long.byte 0x08 0.--7. 1. " RX1_REMOTE_SERVICE_OUTBOUND_READ_RESPONSE_DATA ,RX1_Remote_Service_Outbound_Read_Response_Data" line.long 0x0C "RX1_REMOTE_COMMAND_OUTBOUND_STATUS,RX1_Remote_Command_Outbound_Status" eventfld.long 0x0C 31. " RX1_REMOTE_COMMAND_OUTBOUND_CLEAR ,RX1_Remote_Command_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x0C 0. " RX1_REMOTE_COMMAND_OUTBOUND_BUSY ,RX1_Remote_Command_Outbound_Busy" "Not busy,Busy" line.long 0x10 "RX1_REMOTE_COMMAND_OUTBOUND_DATA,RX1_Remote_Command_Outbound_Data" bitfld.long 0x10 2. " RX1_REMOTE_COMMAND_OUTBOUND_CLEAR_TICKET_COUNTER ,RX1_Remote_Command_Outbound_Clear_Ticket_Counter" "Not clear,Clear" textline " " bitfld.long 0x10 1. " RX1_REMOTE_COMMAND_OUTBOUND_REALIGN ,RX1_Remote_Command_Outbound_Realign" "No,Yes" textline " " bitfld.long 0x10 0. " RX1_REMOTE_COMMAND_OUTBOUND_SOFT_RESET ,RX1_Remote_Command_Outbound_Soft_Reset" "No reset,Reset" width 12. tree.end tree "Channel 2" base ad:0x3A030000 width 31. group.long 0x00++0x07 line.long 0x00 "SWRESET,Resets APIX IP core" bitfld.long 0x00 0. " CFG_VALID ,cfg_valid" "Core in reset,Core enabled" line.long 0x04 "APIXMODE,General configuration register" bitfld.long 0x04 0. " APIX_MODE ,Apix mode" "APIX1,APIX2" group.long 0x08++0x0B line.long 0x00 "FIR_FILTER_0,Configuration for APIX transmitter FIR filter" bitfld.long 0x00 30. " C3SIGN ,Sign FIR coefficient c3" "0,1" bitfld.long 0x00 24.--29. " C3COEFF ,Value FIR coefficient c3" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x00 22. " C2SIGN ,Sign FIR coefficient c2" "0,1" bitfld.long 0x00 16.--21. " C2COEFF ,Value FIR coefficient c2" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x00 14. " C1SIGN ,Sign FIR coefficient c1" "0,1" bitfld.long 0x00 8.--13. " C1COEFF ,Value FIR coefficient c1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x00 6. " C0SIGN ,Sign FIR coefficient c0" "0,1" bitfld.long 0x00 0.--5. " C0COEFF ,Value FIR coefficient c0" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x04 "FIR_FILTER_1,Configuration for APIX transmitter FIR filter" bitfld.long 0x04 2.--4. " FIROUTCOEFF ,Defines the FIR output coefficients d4 d3 d2" "0,1,2,3,4,5,6,7" bitfld.long 0x04 0.--1. " FIRINCOEFF ,Defines the FIR input coefficients b3 b2" "0,1,2,3" line.long 0x08 "CALIB_I_TST_CFG,Calibration Test configuration" bitfld.long 0x08 31. " I_CALIB_EN ,Enable process compensation calibration" "Disabled,Enabled" rgroup.long 0x10++0x03 line.long 0x00 "CALIB_I_TST_STS,Calibration Test status" hexmask.long.word 0x00 16.--26. 1. " I_CALIB ,Internal comparator calibration value" hexmask.long.word 0x00 0.--8. 1. " I_CONTROL ,Process compensation value" group.long 0x14++0x03 line.long 0x00 "CALIB_P_TST_CFG,Calibration Prebuffer Test configuration" bitfld.long 0x00 31. " P_CALIB_EN ,Enable cable dependent calibration" "Disabled,Enabled" rgroup.long 0x18++0x03 line.long 0x00 "CALIB_P_TST_STS,Calibration Prebuffer Test status" hexmask.long.word 0x00 16.--26. 1. " P_CALIB ,Internal comparator calibration value" hexmask.long.word 0x00 0.--8. 1. " P_CONTROL ,Cable dependent calibration value" group.long 0x30++0x17 line.long 0x00 "LINKCFG,Configuration of different toplevel link functions" bitfld.long 0x00 8. " APIX1_GPIOREGEN ,Enables register access to APIX1 SBGIO port" "Disabled,Enabled" bitfld.long 0x00 7. " AICCONNECT1 ,Configuration for AIC 2:3 crossbar(AIC1)" "Disabled,Enabled" textline " " bitfld.long 0x00 6. " AICCONNECT0 ,Configuration for AIC 2:3 crossbar(AIC1)" "Disabled,Enabled" bitfld.long 0x00 4.--5. " AICMODE ,Selects data and direction for AIC pins" "Mode0 2bit AIC,Mode1 1bit AIC,Mode2 2bit AIC-2," textline " " bitfld.long 0x00 0. " PIXCH0SEL ,Selects pixel input for pixel channel 0 output" "Input 0,Input 1" line.long 0x04 "CH0PACKER_COLORCOMPONENTBITS,Color component size of outgoing pixel stream channel 0" bitfld.long 0x04 24.--27. " CH0COMPONENTBITSRED ,Number of red bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x04 16.--19. " CH0COMPONENTBITSGREEN ,Number of green bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x04 8.--11. " CH0COMPONENTBITSBLUE ,Number of blue bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "CH0PACKER_COLORCOMPONENTSHIFT,Color component offset of outgoing pixel stream channel 0" bitfld.long 0x08 24.--28. " CH0COMPONENTSHIFTRED ,Component Shift Red" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x08 16.--20. " CH0COMPONENTSHIFTGREEN ,Component Shift Green" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x08 8.--12. " CH0COMPONENTSHIFTBLUE ,Component Shift Blue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x0C "CH1PACKER_COLORCOMPONENTBITS,Color component size of outgoing pixel stream channel 1" bitfld.long 0x0C 24.--27. " CH1COMPONENTBITSRED ,Number of red bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x0C 16.--19. " CH1COMPONENTBITSGREEN ,Number of green bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x0C 8.--11. " CH1COMPONENTBITSBLUE ,Number of blue bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x10 "CH1PACKER_COLORCOMPONENTSHIFT,Color component offset of outgoing pixel stream channel 1" bitfld.long 0x10 24.--28. " CH1COMPONENTSHIFTRED ,Component Shift Red" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x10 16.--20. " CH1COMPONENTSHIFTGREEN ,Component Shift Green" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x10 8.--12. " CH1COMPONENTSHIFTBLUE ,Component Shift Blue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x14 "APIX12_CFG_0,Inova Config Byte 01" bitfld.long 0x14 0.--1. " DOWNBW ,Setting of the downstream bandwidth" ",M500mode,G1mode,G3mode" textline "" width 18. if (((per.l(ad:0x3A030000+0x04))&0x01)==0x01) group.long 0x48++0x03 line.long 0x00 "APIX12_CFG_2,Inova Config Bytes 0B_0A_09" bitfld.long 0x00 16.--17. " UPSPOFFSET750 ,Upstream sample point multiple of 750 MHz clock cycles" "0 cycles,1 cycles,2 cycles,3 cycles" bitfld.long 0x00 11.--12. " UPSPOFFSET ,Upstream sample point multiple of core clock after detect transitions" "0 cycles,1 cycles,2 cycles,3 cycles" textline " " bitfld.long 0x00 8.--9. " UPSERIALBW ,Upstream serial bandwidth" "APIX2_fast 187.5 Mbit/s,,APIX2_slow 62.5 Mbit/s," bitfld.long 0x00 5. " BACKPREN ,AShell back pressure enable" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " UPWDFAEN ,Watchdog upstream frame alignment" "Disabled,Enabled" bitfld.long 0x00 3. " UPWDBAEN ,Watchdog upstream bit alignment" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " CH1PIXEN ,Enable pixel channel1 in APIX2 core" "Disabled,Enabled" bitfld.long 0x00 0. " CH0PIXEN ,Enable pixel channel0 in APIX2 core" "Disabled,Enabled" else group.long 0x48++0x03 line.long 0x00 "APIX12_CFG_2,Inova Config Bytes 0B_0A_09" bitfld.long 0x00 16.--17. " UPSPOFFSET750 ,Upstream sample point multiple of 750 MHz clock cycles" "0 cycles,1 cycles,2 cycles,3 cycles" bitfld.long 0x00 11.--12. " UPSPOFFSET ,Upstream sample point multiple of core clock after detect transitions" "0 cycles,1 cycles,2 cycles,3 cycles" textline " " bitfld.long 0x00 8.--9. " UPSERIALBW ,Upstream serial bandwidth" ",APIX1_fast 62.5 Mbit/s,,APIX1_slow 31.25 Mbit/s" bitfld.long 0x00 5. " BACKPREN ,AShell back pressure enable" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " UPWDFAEN ,Watchdog upstream frame alignment" "Disabled,Enabled" bitfld.long 0x00 3. " UPWDBAEN ,Watchdog upstream bit alignment" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " CH1PIXEN ,Enable pixel channel1 in APIX2 core" "Disabled,Enabled" bitfld.long 0x00 0. " CH0PIXEN ,Enable pixel channel0 in APIX2 core" "Disabled,Enabled" endif group.long 0x50++0x03 line.long 0x00 "APIX2_CFG_1,Inova COnfig Bytes 10_0F_0E_0D" bitfld.long 0x00 31. " ASHELL2_1_BROADCASTEN ,Broadcast mode of AShell2_1" "Disabled,Enabled" bitfld.long 0x00 30. " ASHELL2_1_LINKERRORTOL ,Link error tolerance of AShell2_1" "0,1" textline " " bitfld.long 0x00 26.--29. " ASHELL2_1_CRCTOCNT ,CRC timeout counter of AShell2_1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 25. " ASHELL2_1_ARQ_DIS ,Disable ARQ of AShell2_1" "No,Yes" textline " " bitfld.long 0x00 24. " ASHELL2_1_EN ,AShell2_1 enable" "Disabled,Enabled" bitfld.long 0x00 23. " ASHELL2_0_BROADCASTEN ,Broadcast mode of AShell2_0" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " ASHELL2_0_LINKERRORTOL ,Link error tolerance of AShell2_0" "0,1" bitfld.long 0x00 18.--21. " ASHELL2_0_CRCTOCNT ,CRC timeout counter of AShell2_0" "Disabled,4,6,10,8,16,24,40,32,64,96,160,256,512,768,1280" textline " " bitfld.long 0x00 17. " ASHELL2_0_ARQ_DIS ,Disable ARQ of AShell2_0" "Yes,No" bitfld.long 0x00 16. " ASHELL2_0_EN ,AShell2_0 enable" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " AUDIOEN ,Audio Interface enable" "Disabled,Enabled" bitfld.long 0x00 10. " AUDIOBW ,Audio bandwidth" "Ordinary bandwidth,High bandwidth" textline " " bitfld.long 0x00 9. " RXDAISYCHAIN ,RX daisy chain" "1 Apix2 DC off,2 Apix2 DC on" if (((per.l(ad:0x3A030000+0x44))&0x03)==0x01) group.long 0x54++0x03 line.long 0x00 "APIX2_CFG_2,Inova Config Bytes 13_12_11" bitfld.long 0x00 22. " GPIODWNBW ,GPIO downstream bandwidth mode" "Low speed,High speed" bitfld.long 0x00 21. " GPIODWNHALFBW ,Halve GPIO downstream bandwidth" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " GPIOUPBW ,GPIO upstream bandwidth mode" "Low speed,High speed" textline " " bitfld.long 0x00 19. " GPIO0UPEN ,GPIO0 upstream channel enable" "Disabled,Enabled" bitfld.long 0x00 18. " GPIO1UPEN ,GPIO1 upstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " GPIO0DWNEN ,GPIO0 downstream channel enable" "Disabled,Enabled" bitfld.long 0x00 16. " GPIO1DWNEN ,GPIO1 downstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 14.--15. " ASH2DWNDIV ,AShell2 downstream bandwidth divider" "/1,/2,/4,/8" bitfld.long 0x00 9.--13. " DOWNDATABW ,Totally available downstream bandwidth for AShell data audio and GPIO" ",56 MBit/s,42 MBit/s,,29 MBit/s,,,,15 MBit/s,,,,,,,,1.3 MBit/s,..." textline " " bitfld.long 0x00 6. " BULKDATAEN ,Bulk data mode" "Disabled,Enabled" bitfld.long 0x00 5. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24bits,21 bits" textline " " bitfld.long 0x00 3.--4. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "BpP10,BpP12,BpP18,BpP24" bitfld.long 0x00 2. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24bits,21bits" textline " " bitfld.long 0x00 0.--1. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "BpP10,BpP12,BpP18,BpP24" elif (((per.l(ad:0x3A030000+0x44))&0x03)==0x02) group.long 0x54++0x03 line.long 0x00 "APIX2_CFG_2,Inova Config Bytes 13_12_11" bitfld.long 0x00 22. " GPIODWNBW ,GPIO downstream bandwidth mode" "Low speed,High speed" bitfld.long 0x00 21. " GPIODWNHALFBW ,Halve GPIO downstream bandwidth" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " GPIOUPBW ,GPIO upstream bandwidth mode" "Low speed,High speed" textline " " bitfld.long 0x00 19. " GPIO0UPEN ,GPIO0 upstream channel enable" "Disabled,Enabled" bitfld.long 0x00 18. " GPIO1UPEN ,GPIO1 upstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " GPIO0DWNEN ,GPIO0 downstream channel enable" "Disabled,Enabled" bitfld.long 0x00 16. " GPIO1DWNEN ,GPIO1 downstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 14.--15. " ASH2DWNDIV ,AShell2 downstream bandwidth divider" "/1,/2,/4,/8" bitfld.long 0x00 9.--13. " DOWNDATABW ,Totally available downstream bandwidth for AShell data audio and GPIO" ",113 MBit/s,85 MBit/s,,58 MBit/s,,,,30 MBit/s,..." textline " " bitfld.long 0x00 6. " BULKDATAEN ,Bulk data mode" "Disabled,Enabled" bitfld.long 0x00 5. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24bits,21 bits" textline " " bitfld.long 0x00 3.--4. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "10bit per pixel,12bit per pixel,18bit per pixel,24" bitfld.long 0x00 2. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24bits,21bits" textline " " bitfld.long 0x00 0.--1. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "10bit per pixel,12bit per pixel,18bit per pixel,24" elif (((per.l(ad:0x3A030000+0x44))&0x03)==0x03) group.long 0x54++0x03 line.long 0x00 "APIX2_CFG_2,Inova Config Bytes 13_12_11" bitfld.long 0x00 22. " GPIODWNBW ,GPIO downstream bandwidth mode" "Low speed,High speed" bitfld.long 0x00 21. " GPIODWNHALFBW ,Halve GPIO downstream bandwidth" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " GPIOUPBW ,GPIO upstream bandwidth mode" "Low speed,High speed" textline " " bitfld.long 0x00 19. " GPIO0UPEN ,GPIO0 upstream channel enable" "Disabled,Enabled" bitfld.long 0x00 18. " GPIO1UPEN ,GPIO1 upstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " GPIO0DWNEN ,GPIO0 downstream channel enable" "Disabled,Enabled" bitfld.long 0x00 16. " GPIO1DWNEN ,GPIO1 downstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 14.--15. " ASH2DWNDIV ,AShell2 downstream bandwidth divider" "/1,/2,/4,/8" bitfld.long 0x00 9.--13. " DOWNDATABW ,Totally available downstream bandwidth for AShell data audio and GPIO" ",340 MBit/s,257 MBit/s,,174 MBit/s,,,,91 MBit/s,..." textline " " bitfld.long 0x00 6. " BULKDATAEN ,Bulk data mode" "Disabled,Enabled" bitfld.long 0x00 5. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24bits,21 bits" textline " " bitfld.long 0x00 3.--4. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "BpP10,BpP12,BpP18,BpP24" bitfld.long 0x00 2. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24bits,21bits" textline " " bitfld.long 0x00 0.--1. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "BpP10,BpP12,BpP18,BpP24" else group.long 0x54++0x03 line.long 0x00 "APIX2_CFG_2,Inova Config Bytes 13_12_11" bitfld.long 0x00 22. " GPIODWNBW ,GPIO downstream bandwidth mode" "Low speed,High speed" bitfld.long 0x00 21. " GPIODWNHALFBW ,Halve GPIO downstream bandwidth" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " GPIOUPBW ,GPIO upstream bandwidth mode" "Low speed,High speed" textline " " bitfld.long 0x00 19. " GPIO0UPEN ,GPIO0 upstream channel enable" "Disabled,Enabled" bitfld.long 0x00 18. " GPIO1UPEN ,GPIO1 upstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " GPIO0DWNEN ,GPIO0 downstream channel enable" "Disabled,Enabled" bitfld.long 0x00 16. " GPIO1DWNEN ,GPIO1 downstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 14.--15. " ASH2DWNDIV ,AShell2 downstream bandwidth divider" "/1,/2,/4,/8" textline " " bitfld.long 0x00 6. " BULKDATAEN ,Bulk data mode" "Disabled,Enabled" bitfld.long 0x00 5. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24bits,21 bits" textline " " bitfld.long 0x00 3.--4. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "BpP10,BpP12,BpP18,BpP24" bitfld.long 0x00 2. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24bits,21bits" textline " " bitfld.long 0x00 0.--1. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "BpP10,BpP12,BpP18,BpP24" endif group.long 0x58++0x17 line.long 0x00 "APIX1_CFG_0,Inova Config Byte 14" hexmask.long.byte 0x00 24.--30. 1. " SBDOWN_DATA_CYCLETIME6TO0 ,Cycle time of sbdown clock in multiples of 8ns" line.long 0x04 "APIX1_CFG_1,Inova Config Bytes 18_17_16_15" bitfld.long 0x04 27.--28. " PX_CTRL_PIGGYBACK ,APIX PHY (Soft IP): transmission of pixel controls" "Never,Unused,With even pixels only,With every pixel" bitfld.long 0x04 25.--26. " PIXEL_DATA_WIDTH ,Pixel data width" "10bit per pixel,12bit per pixel,18bit per pixel,24" textline " " bitfld.long 0x04 23. " ARQ_DISABLE ,Retransmission disable" "No,Yes" bitfld.long 0x04 22. " SUPPRESS_IDLE ,Suppress idle transmission to reduce data traffic" "Disabled,Enabled" textline " " bitfld.long 0x04 16.--18. " SBDOWN_DATA_CYCLETIME9TO7 ,Upper bits of sbdown_data_cycletime" "0,1,2,3,4,5,6,7" bitfld.long 0x04 12.--15. " CRC_TIME_OUT_VALUE ,CRC timeout value" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x04 8.--11. " WINDOW_SIZE ,AShell window size Window size of the retransmission protocol" ",1,2,3,4,5,6,7,8,9,10,11,12,,," bitfld.long 0x04 7. " SBUP_DWIDTH ,Enable sbup data ports" "1 bit,2 bit" textline " " bitfld.long 0x04 6. " SBUP_DACLK ,Validate sbup_data automatic or with transmitted valid" "Disabled,Enabled" bitfld.long 0x04 5. " SBDOWN_DWIDTH ,Enable sbdown data ports" "1 bit data and valid,2 bit data" textline " " bitfld.long 0x04 3.--4. " SBDOWN_DACLK ,Generate sbdown clock and transmit as sbdown_data[1]" ",Sbdown_trigger,Internal counter," bitfld.long 0x04 1. " ESHELLEN ,Connect internal APIX1 PHY to external sideband data through APIX1 SBGPIO (AIC) interface" "Disabled,Enabled" textline " " bitfld.long 0x04 0. " SPI_OVER_SB ,Selects between two different sideband transmission modes" "Full data mode,SPI mode" line.long 0x08 "APIX1_CFG_2,Inova Config Bytes 1C_1B_1A_19" hexmask.long.byte 0x08 25.--31. 1. " SBDOWN_CLOCK_HIGH_PULSE ,Configure high pulse width of signal 'sb_down_clk' if sb_down_clk and sb_up_clk enable" hexmask.long.byte 0x08 17.--23. 1. " SBDOWN_CLOCK_CYCLES ,Configures sbdown clk cycle" textline " " bitfld.long 0x08 15. " DDOWN_ENABLE ,APIX PHY (Soft IP) / AShell: configure downstream data path" "Pixel stream mode,Data mode" bitfld.long 0x08 14. " EXT_SB_DATA_DIS ,Sideband data are 2-stage registered internal have to be used with external sideband data" "External,No external" textline " " bitfld.long 0x08 11. " ASHELL1_EN ,APIX1 Ashell1" "Disabled,Enabled" bitfld.long 0x08 10. " SB_CLK_EN ,Enable sb_down_clk and sb_up_clk" "Disabled,Enabled" textline " " bitfld.long 0x08 8.--9. " SB_UP_CLK_CYCLES ,Configure high pulse width of signal 'sb_up_clk' if sb_down_clk and sb_up_clk enable" "1cycle,2cycles,3cysles,4cycles" line.long 0x0C "APIX1_CFG_3,Inova Config Byte 1D" hexmask.long.byte 0x0C 1.--7. 1. " SBDOWN_CLOCK_START_POS ,Start position of signal sbdown_clk relative to internal \u2018strobe position\u2019" line.long 0x10 "TEST_CONFIG,Config for Inova BIST Test" hexmask.long.word 0x10 16.--31. 1. " TEST_PATTERN ,Test pattern" bitfld.long 0x10 12. " TESTPATTERN_EN ,Test pattern generation" "Disabled,Enabled" textline " " bitfld.long 0x10 11. " PSRTEST_MODE ,PSR test pattern generation" "Disabled,Enabled" bitfld.long 0x10 9.--10. " PSRTEST_8B10B ,Psr Test 8B10B" "Run length 8,Run length 10,Run length 12,Run length 16" textline " " bitfld.long 0x10 8. " BG_MASK_DISABLE ,Line coder mask disable" "No,Yes" line.long 0x14 "AAC,Configuration for AShell1-to-AShell1 - Connector (AAC)" bitfld.long 0x14 14.--15. " AACOFFSET ,Cfg_data[15:14] offset between edges of AAC clock and AAC data[1:0] as multiples of core clock" "1cycle,2cycles,3cycles,4cycles" hexmask.long.word 0x14 2.--13. 1. " AACFREQUENCY ,Defines AAC clock frequency" textline " " bitfld.long 0x14 1. " AACEN ,Data path selection" "APIX1 PHY,ACC" bitfld.long 0x14 0. " AACMODE ,AAC clock mode" "Both edges,Rising edges" group.long 0x70++0x0B line.long 0x00 "AAA,Configuration for Ashell1-to-Ashell2 Adapter" bitfld.long 0x00 1. " AAAEN ,AShell1 to AShell2 Adapter enable" "Disabled,Enabled" bitfld.long 0x00 0. " ASHELL2_SELECT ,Ashell2 select" "AShell2_1,AShell2_0" line.long 0x04 "APIX1_GPO,GPIO DATA for APIX1 communication" bitfld.long 0x04 0.--1. " APIX1_GPO ,2 bit GPIO output data corresponds to GPIO pins of INAP1 device" "0,1,2,3" line.long 0x08 "APIX1_GPI_INTCFG,APIX1GPI INTCFG" bitfld.long 0x08 1. " APIX1_GPI_INTCFG ,APIX1_GPI_INTCFG" "Rising edge,Falling edge" bitfld.long 0x08 0. " APIX0_GPI_INTCFG ,APIX0_GPI_INTCFG" "Rising edge,Falling edge" rgroup.long 0x7C++0x03 line.long 0x00 "APIX1_GPI,GPIO DATA for APIX1 communication" bitfld.long 0x00 0.--1. " APIX1_GP1 ,2 bit GPIO output data corresponds to GPIO pins of INAP1 device" "0,1,2,3" group.long 0x80++0x07 line.long 0x00 "APIX2_GPO,GPIO DATA for APIX2 communication" bitfld.long 0x00 0.--1. " APIX2_GPO ,2 bit GPIO output data corresponds to GPIO pins of INAP1 device" "0,1,2,3" line.long 0x04 "APIX2_GPI_INTCFG,APIX2_GPI_INTCFG" bitfld.long 0x04 3. " APIX2_GPI_INTCFG[3] ,APIX2_GPI_INTCFG[3]" "Rising edge,Falling edge" bitfld.long 0x04 2. " APIX2_GPI_INTCFG[2] ,APIX2_GPI_INTCFG[2]" "Rising edge,Falling edge" textline " " bitfld.long 0x04 1. " APIX2_GPI_INTCFG[1] ,APIX2_GPI_INTCFG[1]" "Rising edge,Falling edge" bitfld.long 0x04 0. " APIX2_GPI_INTCFG[0] ,APIX2_GPI_INTCFG[0]" "Rising edge,Falling edge" rgroup.long 0x88++0x03 line.long 0x00 "APIX2_GPI,GPIO DATA for APIX2 communication" bitfld.long 0x00 0.--3. " APIX2_GPI ,2 bit GPIO input data, corresponds to GPIO pins of INAP1 device" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" group.long 0x200++0x07 line.long 0x00 "APIX_CTRL_0,Signals to AShell restart and counter clears" eventfld.long 0x00 4. " ASHELL2_1_TCNT_CLEAR ,AShell2_1_tcnt_clear" "Not clear,Clear" eventfld.long 0x00 3. " ASHELL2_0_TCNT_CLEAR ,AShell2_0_tcnt_clear" "Not clear,Clear" textline " " eventfld.long 0x00 2. " ASHELL1_REALIGN ,Apix1 AShell realign by writing a 1" "Not realign,Realign" eventfld.long 0x00 1. " ASHELL2_1_REALIGN ,AShell2_1 realign by writing a 1" "Not realign,Realign" textline " " eventfld.long 0x00 0. " ASHELL2_0_REALIGN ,AShell2_0 realign by writing a 1" "Not realign,Realign" line.long 0x04 "APIX_CTRL_1,Reset for counter values" eventfld.long 0x04 5. " ASHELL2_0_CRCERRCNTCLEAR ,Clear Ashell2_0_CRCErrCnt by writing a 1" "Not clear,Clear" eventfld.long 0x04 4. " ASHELL2_1_CRCERRCNTCLEAR ,Clear Ashell2_1_CRCErrCnt by writing a 1" "Not clear,Clear" textline " " eventfld.long 0x04 3. " APIX1UPFALIGNERRCNTCLEAR ,Clear Apix1upFAlignErrCnt by writing a 1" "Not clear,Clear" eventfld.long 0x04 2. " ASHELL1_CRCERRCNTCLEAR ,Clear Ashell2_1_CRCErrCnt by writing a 1" "Not clear,Clear" textline " " eventfld.long 0x04 1. " APIX2UPFALIGNERRCNTCLEAR ,Clear Apix2upFAlignErrCnt by writing a 1" "Not clear,Clear" group.long 0x208++0x0B line.long 0x00 "APIX12_STATUS_0,Status from Inova Status bytes 01 and 02 PHY status pixelstream status" rbitfld.long 0x00 12. " APIX2UPFALIGN ,Apix2 upstream frame aligned" "No,Yes" rbitfld.long 0x00 8.--11. " APIX2UPFALIGNERRCNT ,APIX2 upstream frame aligned error counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 0. " UPBITALIGNED ,Upstream bit aligned" "0,1" line.long 0x04 "APIX2_STATUS_0,Status from Inova Status bytes 06_05_04_03 Pixelstream status Ashell2_0 Status" hexmask.long.byte 0x04 24.--31. 1. " ASHELL2_0_TADIFFCNT ,Transaction counter difference of AShell2_0" rbitfld.long 0x04 17. " ASHELL2_0_OPERATIONAL ,AShell operational" "Not asserted,Asserted" textline " " hexmask.long.byte 0x04 8.--15. 1. " ASHELL2_0_CRCERRCNT ,CRC error counter of AShell2_0" rbitfld.long 0x04 7. " CH1HSYNCPOL ,Pixel channel 1 horizontal polarity" "Active low,Active high" textline " " rbitfld.long 0x04 6. " CH1VSYNCPOL ,Pixel channel 1 vertical polarity" "Active low,Active high" rbitfld.long 0x04 5. " CH1PIXFIFOEMPTY ,Pixel channel 1 FIFO underflow" "No,Yes" textline " " rbitfld.long 0x04 4. " CH1PIXFIFOFULL ,Pixel channel 1 FIFO overflow" "No,Yes" rbitfld.long 0x04 3. " CH0HSYNCPOL ,Pixel channel 0 horizontal polarity" "Active low,Active high" textline " " rbitfld.long 0x04 2. " CH0VSYNCPOL ,Pixel channel 0 vertical polarity" "Active low,Active high" rbitfld.long 0x04 1. " CH0PIXFIFOEMPTY ,Pixel channel 0 FIFO underflow" "No,Yes" textline " " bitfld.long 0x04 0. " CH0PIXFIFOFULL ,Pixel channel 0 FIFO overflow" "No,Yes" line.long 0x08 "APIX2_STATUS_1,Status from Inova Status bytes 09_08_07 Ashell2_1 status" hexmask.long.byte 0x08 24.--31. 1. " ASHELL2_1_TADIFFCNT ,Transaction counter difference of AShell2_1" rbitfld.long 0x08 17. " ASHELL2_1_OPERATIONAL ,AShell operational" "Not asserted,Asserted" textline " " hexmask.long.byte 0x08 8.--15. 1. " ASHELL2_1_CRCERRCNT ,CRC error counter of AShell2_0 Number of received CRC errors" rgroup.long 0x214++0x03 line.long 0x00 "APIX1_STATUS_0,Status from Inova Status bytes 0C_0B_0A Ashell1 and APIX1 PHY" bitfld.long 0x00 22. " APIX1UPFRAMEALIGNED ,Apix1 upstream frame aligned" "No,Yes" bitfld.long 0x00 16.--21. " APIX1UPFRAMEALIGNEDERRCNT ,Apix1 upstream frame aligned error counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x00 8.--13. " ASHELL1_CRCERRCNT ,Apix1 AShell CRC error counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x00 6. " ASHELL1_OPERATIONAL ,Apix1 AShell operational" "Not asserted,Asserted" tree "Interrupt registers" width 13. rgroup.long 0x300++0x0B line.long 0x00 "INTSTATUS0,Interrupt Status Register 0" bitfld.long 0x00 31. " RX1_REMOTE_INBOUND_I2C_JOB_CANCEL ,APIX2 Remote command cancel I2C job received from device RX1" "Inactive,Active" bitfld.long 0x00 30. " RX1_REMOTE_INBOUND_ASHELL2_CLEAR_TICKET_COUNTER ,APIX2 Remote command clear Ashell2 ticket counter received from device RX1" "Inactive,Active" textline " " bitfld.long 0x00 29. " RX1_REMOTE_INBOUND_ASHELL2_REALIGN ,APIX2 Remote command realign Ashell2 received from device RX1" "Inactive,Active" bitfld.long 0x00 28. " RX1_REMOTE_INBOUND_SOFT_RESET ,APIX2 Remote command soft reset received from device RX1" "Inactive,Active" textline " " bitfld.long 0x00 27. " RX0_REMOTE_INBOUND_I2C_JOB_CANCEL ,APIX2 Remote command cancel I2C job received from device RX0" "Inactive,Active" bitfld.long 0x00 26. " RX0_REMOTE_INBOUND_ASHELL2_CLEAR_TICKET_COUNTER ,APIX2 Remote command clear Ashell2 ticket counter received from device RX0" "Inactive,Active" textline " " bitfld.long 0x00 25. " RX0_REMOTE_INBOUND_ASHELL2_REALIGN ,APIX2 Remote command realign Ashell2 received from device RX0" "Inactive,Active" bitfld.long 0x00 24. " RX0_REMOTE_INBOUND_SOFT_RESET ,APIX2 Remote command soft reset received from device RX0" "Inactive,Active" textline " " bitfld.long 0x00 23. " GPI_1 ,APIX1 GPIO Edge detected at APIX1 GPI_1 port" "Inactive,Active" bitfld.long 0x00 22. " GPI_0 ,APIX1 GPIO Edge detected at APIX1 GPI_0 port" "Inactive,Active" textline " " bitfld.long 0x00 21. " ASHELL1_FATAL ,APIX1 Ashell1 Fatal Error" "Inactive,Active" bitfld.long 0x00 20. " ASHELL1_CRCERROR ,APIX1 Ashell1 detected CRC error at incoming data" "Inactive,Active" textline " " bitfld.long 0x00 19. " ASHELL1_UNCONNECTED ,APIX1 Ashell1 unconnected with remote Ashell" "Inactive,Active" bitfld.long 0x00 18. " ASHELL1_CONNECTED ,APIX1 Ashell1 connected with remote Ashell" "Inactive,Active" textline " " bitfld.long 0x00 17. " ASHELL1_CRCTIMEOUT ,APIX1 Ashell1 CRC error threshold was reached" "Inactive,Active" bitfld.long 0x00 16. " ASHELL1_PROTERR ,APIX1 Ashell1 Protocoll Error" "Inactive,Active" textline " " bitfld.long 0x00 15. " ASHELL1_REMRESTARTED ,APIX1 Ashell1 Remote Ashell1 was restarted" "Inactive,Active" bitfld.long 0x00 14. " ASHELL2_1_UNCONNECTED ,APIX2 Ashell2_1 unconnected with remote Ashell" "Inactive,Active" textline " " bitfld.long 0x00 13. " ASHELL2_1_CONNECTED ,APIX2 Ashell2_1 connected with remote Ashell" "Inactive,Active" bitfld.long 0x00 12. " ASHELL2_1_TRANSACTION_LOSS ,APIX2 Ashell2_1 Transaction Loss Error" "Inactive,Active" textline " " bitfld.long 0x00 11. " ASHELL2_1_FATAL ,APIX2 Ashell2_1 Fatal Error" "Inactive,Active" bitfld.long 0x00 10. " ASHELL2_1_CRCERROR ,APIX2 Ashell2_1 CRC error" "Inactive,Active" textline " " bitfld.long 0x00 9. " ASHELL2_0_UNCONNECTED ,APIX2 Ashell2_0 unconnected with remote Ashell" "Inactive,Active" bitfld.long 0x00 8. " ASHELL2_0_CONNECTED ,APIX2 Ashell2_0 connected with remote Ashell" "Inactive,Active" textline " " bitfld.long 0x00 7. " ASHELL2_0_TRANSACTION_LOSS ,APIX2 Ashell2_0 Transaction Loss Error" "Inactive,Active" bitfld.long 0x00 6. " ASHELL2_0_FATAL ,APIX2 Ashell2_0 Fatal Error" "Inactive,Active" textline " " bitfld.long 0x00 5. " ASHELL2_0_CRCERROR ,APIX2 Ashell2_0 CRC error" "Inactive,Active" bitfld.long 0x00 4. " CH0PIXFIFOFULL_INT ,APIX2 PIX Channel 0 pixelfifo overflow error" "Inactive,Active" textline " " bitfld.long 0x00 3. " CH0PIXFIFOEMPTY_INT ,APIX2 PIX Channel 0 pixelfiifo underflow error" "Inactive,Active" bitfld.long 0x00 2. " CH1PIXFIFOFULL_INT ,APIX2 PIX Channel 1 pixelfifo overflow error" "Inactive,Active" textline " " bitfld.long 0x00 1. " CH1PIXFIFOEMPTY_INT ,APIX2 PIX Channel 1 pixelfiifo underflow error" "Inactive,Active" bitfld.long 0x00 0. " UPBITALIGNEDLOSS ,PHY Loss of upstream PHY Bit alignment" "Inactive,Active" line.long 0x04 "INTSTATUS1,Interrupt Status Register 1" bitfld.long 0x04 31. " RX1_REMOTE_SERVICE_INBOUND_ERROR_INT ,APIX2 remote IF Data loss at inbound remote service data register (Rx1)" "Inactive,Active" bitfld.long 0x04 30. " RX1_REMOTE_SERVICE_INBOUND_VALID_INT ,APIX2 remote IF Received valid inbound data from remote service IF of device RX1" "Inactive,Active" textline " " bitfld.long 0x04 29. " RX1_REMOTE_CONTROLLER_INBOUND_ERROR_INT ,APIX2 remote IF Data loss at inbound remote control data register (RX1)" "Inactive,Active" bitfld.long 0x04 28. " RX1_REMOTE_CONTROLLER_INBOUND_VALID_INT ,APIX2 remote IF Received valid inbound data from remote control IF of device RX1" "Inactive,Active" textline " " bitfld.long 0x04 27. " RX0_REMOTE_SERVICE_INBOUND_ERROR_INT ,APIX2 remote IF Data loss at inbound remote service data register (Rx0)" "Inactive,Active" bitfld.long 0x04 26. " RX0_REMOTE_SERVICE_INBOUND_VALID_INT ,APIX2 remote IF Received valid inbound data from remote service IF of device RX0" "Inactive,Active" textline " " bitfld.long 0x04 25. " RX0_REMOTE_CONTROLLER_INBOUND_ERROR_INT ,APIX2 remote IF Data loss at inbound remote control data register (RX0)" "Inactive,Active" bitfld.long 0x04 24. " RX0_REMOTE_CONTROLLER_INBOUND_VALID_INT ,APIX2 remote IF Received valid inbound data from remote control IF of device RX0" "Inactive,Active" textline " " bitfld.long 0x04 23. " RX1_I2C_INBOUND_READ_RESPONSE_ERROR_INT ,APIX2 remote IF Data loss at i2c inbound read response register (RX1)" "Inactive,Active" bitfld.long 0x04 22. " RX1_I2C_INBOUND_READ_RESPONSE_VALID_INT ,APIX2 I2C Received valid inbound I2C read response from device RX1" "Inactive,Active" textline " " bitfld.long 0x04 21. " RX1_I2C_INBOUND_STATUS_ERROR_INT ,APIX2 I2C Data loss at inbound i2c status register (RX1)" "Inactive,Active" bitfld.long 0x04 20. " RX1_I2C_INBOUND_STATUS_VALID_INT ,APIX2 I2C Received valid inbound i2c status from device RX1" "Inactive,Active" textline " " bitfld.long 0x04 19. " RX1_I2C_INBOUND_JOB_SPEC_ERROR_INT ,APIX2 I2C Data loss at i2c job specification register (RX1)" "Inactive,Active" bitfld.long 0x04 18. " RRX1_I2C_INBOUND_JOB_SPEC_VALID_INT ,APIX2 I2C Received valid inbound i2c job specification from device RX1" "Inactive,Active" textline " " bitfld.long 0x04 17. " RX0_I2C_INBOUND_READ_RESPONSE_ERROR_INT ,APIX2 I2C Data loss at i2c inbound read response register (RX0)" "Inactive,Active" bitfld.long 0x04 16. " RX0_I2C_INBOUND_READ_RESPONSE_VALID_INT ,APIX2 I2C Received valid inbound I2C read response from device RX0" "Inactive,Active" textline " " bitfld.long 0x04 15. " RX0_I2C_INBOUND_STATUS_ERROR_INT ,APIX2 I2C Data loss at inbound i2c status register (RX0)" "Inactive,Active" bitfld.long 0x04 14. " RX0_I2C_INBOUND_STATUS_VALID_INT ,APIX2 I2C Received valid inbound i2c status from device RX0" "Inactive,Active" textline " " bitfld.long 0x04 13. " RX0_I2C_INBOUND_JOB_SPEC_ERROR_INT ,APIX2 I2C Data loss at i2c job specification register (RX0)" "Inactive,Active" bitfld.long 0x04 12. " RX0_I2C_INBOUND_JOB_SPEC_VALID_INT ,APIX2 I2C Received valid inbound i2c job specification from device RX0" "Inactive,Active" textline " " bitfld.long 0x04 11. " WDG_TIMEOUT_INT ,Message buffer Wrbuf Watchdog timeout" "Inactive,Active" bitfld.long 0x04 10. " WRBUF_EMPTY_INT ,Message buffer Write buffer #1 becomes empty" "Inactive,Active" textline " " bitfld.long 0x04 9. " WRBUF_FULL_INT ,Message buffer Write buffer #1 becomes full" "Inactive,Active" bitfld.long 0x04 8. " R1BUF_NOT_EMPTY ,Message buffer Read buffer #1 becomes not empty" "Inactive,Active" textline " " bitfld.long 0x04 7. " R1BUF_FULL_INT ,Message buffer Read buffer #1 becomes full" "Inactive,Active" bitfld.long 0x04 6. " R0BUF_NOT_EMPTY ,Message buffer Read buffer #0 becomes not empty" "Inactive,Active" textline " " bitfld.long 0x04 5. " R0BUF_FULL_INT ,Message buffer Read buffer #0 becomes full" "Inactive,Active" bitfld.long 0x04 4. " WRBUF_OVERFLOW ,Message buffer Write buffer overflow" "Inactive,Active" textline " " bitfld.long 0x04 3. " R1BUF_UNDERRUN ,Message buffer Read buffer #1 underrun" "Inactive,Active" bitfld.long 0x04 2. " R1BUF_OVERFLOW ,Message buffer Read buffer #1 overflow" "Inactive,Active" textline " " bitfld.long 0x04 1. " R0BUF_UNDERRUN ,Message buffer Read buffer #0 underrun" "Inactive,Active" bitfld.long 0x04 0. " R0BUF_OVERFLOW ,Message buffer Read buffer #0 overflow" "Inactive,Active" line.long 0x08 "INTSTATUS2,Interrupt Status Register 2" bitfld.long 0x08 6. " FRAME_ALIGNMENT_TIMEOUT_DETECT ,PHY signalizes that the device was not frame aligned" "Inactive,Active" bitfld.long 0x08 5. " DEBUG_TIMEOUT ,APIX2TX_link Abort of read access to debug register happened" "Inactive,Active" textline " " bitfld.long 0x08 4. " STATUS_TIMEOUT ,APIX2TX_link Abort of read access to status register happened" "Inactive,Active" bitfld.long 0x08 3. " APIX2_GPI_1_RX1 ,APIX2 GPIO Rising or falling edge detected at APIX2 GPI1 from device RX1" "Inactive,Active" textline " " bitfld.long 0x08 2. " APIX2_GPI_0_RX1 ,APIX2 GPIO Rising or falling edge detected at APIX2 GPI0 from device RX1" "Inactive,Active" bitfld.long 0x08 1. " APIX2_GPI_1_RX0 ,APIX2 GPIO Rising or falling edge detected at APIX2 GPI1 from device RX0" "Inactive,Active" textline " " bitfld.long 0x08 0. " APIX2_GPI_0_RX0 ,APIX2 GPIO Rising or falling edge detected at APIX2 GPI0 from device RX0" "Inactive,Active" textline "" ;section group.long 0x30C++0x2F line.long 0x00 "INT0ENABLE0,Interrupt Enable Register 0 for interrupts bits" bitfld.long 0x00 31. " INT0ENABLE0_[31] ,Interrupt 0 Enable bit 31" "Disabled,Enabled" bitfld.long 0x00 30. " [30] ,Interrupt 0 Enable bit 30" "Disabled,Enabled" bitfld.long 0x00 29. " [29] ,Interrupt 0 Enable bit 29" "Disabled,Enabled" bitfld.long 0x00 28. " [28] ,Interrupt 0 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x00 27. " [27] ,Interrupt 0 Enable bit 27" "Disabled,Enabled" bitfld.long 0x00 26. " [26] ,Interrupt 0 Enable bit 26" "Disabled,Enabled" bitfld.long 0x00 25. " [25] ,Interrupt 0 Enable bit 25" "Disabled,Enabled" bitfld.long 0x00 24. " [24] ,Interrupt 0 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x00 23. " [23] ,Interrupt 0 Enable bit 23" "Disabled,Enabled" bitfld.long 0x00 22. " [22] ,Interrupt 0 Enable bit 22" "Disabled,Enabled" bitfld.long 0x00 21. " [21] ,Interrupt 0 Enable bit 21" "Disabled,Enabled" bitfld.long 0x00 20. " [20] ,Interrupt 0 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " [19] ,Interrupt 0 Enable bit 19" "Disabled,Enabled" bitfld.long 0x00 18. " [18] ,Interrupt 0 Enable bit 18" "Disabled,Enabled" bitfld.long 0x00 17. " [17] ,Interrupt 0 Enable bit 17" "Disabled,Enabled" bitfld.long 0x00 16. " [16] ,Interrupt 0 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x00 15. " [15] ,Interrupt 0 Enable bit 15" "Disabled,Enabled" bitfld.long 0x00 14. " [14] ,Interrupt 0 Enable bit 14" "Disabled,Enabled" bitfld.long 0x00 13. " [13] ,Interrupt 0 Enable bit 13" "Disabled,Enabled" bitfld.long 0x00 12. " [12] ,Interrupt 0 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " [11] ,Interrupt 0 Enable bit 11" "Disabled,Enabled" bitfld.long 0x00 10. " [10] ,Interrupt 0 Enable bit 10" "Disabled,Enabled" bitfld.long 0x00 9. " [9] ,Interrupt 0 Enable bit 9" "Disabled,Enabled" bitfld.long 0x00 8. " [8] ,Interrupt 0 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " [7] ,Interrupt 0 Enable bit 7" "Disabled,Enabled" bitfld.long 0x00 6. " [6] ,Interrupt 0 Enable bit 6" "Disabled,Enabled" bitfld.long 0x00 5. " [5] ,Interrupt 0 Enable bit 5" "Disabled,Enabled" bitfld.long 0x00 4. " [4] ,Interrupt 0 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " [3] ,Interrupt 0 Enable bit 3" "Disabled,Enabled" bitfld.long 0x00 2. " [2] ,Interrupt 0 Enable bit 2" "Disabled,Enabled" bitfld.long 0x00 1. " [1] ,Interrupt 0 Enable bit 1" "Disabled,Enabled" bitfld.long 0x00 0. " [0] ,Interrupt 0 Enable bit 0" "Disabled,Enabled" line.long 0x04 "INT0ENABLE1,Interrupt Enable Register 1 for interrupts bits" bitfld.long 0x04 31. " INT0ENABLE1_[31] ,Interrupt 0 Enable bit 31" "Disabled,Enabled" bitfld.long 0x04 30. " [30] ,Interrupt 0 Enable bit 30" "Disabled,Enabled" bitfld.long 0x04 29. " [29] ,Interrupt 0 Enable bit 29" "Disabled,Enabled" bitfld.long 0x04 28. " [28] ,Interrupt 0 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x04 27. " [27] ,Interrupt 0 Enable bit 27" "Disabled,Enabled" bitfld.long 0x04 26. " [26] ,Interrupt 0 Enable bit 26" "Disabled,Enabled" bitfld.long 0x04 25. " [25] ,Interrupt 0 Enable bit 25" "Disabled,Enabled" bitfld.long 0x04 24. " [24] ,Interrupt 0 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x04 23. " [23] ,Interrupt 0 Enable bit 23" "Disabled,Enabled" bitfld.long 0x04 22. " [22] ,Interrupt 0 Enable bit 22" "Disabled,Enabled" bitfld.long 0x04 21. " [21] ,Interrupt 0 Enable bit 21" "Disabled,Enabled" bitfld.long 0x04 20. " [20] ,Interrupt 0 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x04 19. " [19] ,Interrupt 0 Enable bit 19" "Disabled,Enabled" bitfld.long 0x04 18. " [18] ,Interrupt 0 Enable bit 18" "Disabled,Enabled" bitfld.long 0x04 17. " [17] ,Interrupt 0 Enable bit 17" "Disabled,Enabled" bitfld.long 0x04 16. " [16] ,Interrupt 0 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x04 15. " [15] ,Interrupt 0 Enable bit 15" "Disabled,Enabled" bitfld.long 0x04 14. " [14] ,Interrupt 0 Enable bit 14" "Disabled,Enabled" bitfld.long 0x04 13. " [13] ,Interrupt 0 Enable bit 13" "Disabled,Enabled" bitfld.long 0x04 12. " [12] ,Interrupt 0 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x04 11. " [11] ,Interrupt 0 Enable bit 11" "Disabled,Enabled" bitfld.long 0x04 10. " [10] ,Interrupt 0 Enable bit 10" "Disabled,Enabled" bitfld.long 0x04 9. " [9] ,Interrupt 0 Enable bit 9" "Disabled,Enabled" bitfld.long 0x04 8. " [8] ,Interrupt 0 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x04 7. " [7] ,Interrupt 0 Enable bit 7" "Disabled,Enabled" bitfld.long 0x04 6. " [6] ,Interrupt 0 Enable bit 6" "Disabled,Enabled" bitfld.long 0x04 5. " [5] ,Interrupt 0 Enable bit 5" "Disabled,Enabled" bitfld.long 0x04 4. " [4] ,Interrupt 0 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x04 3. " [3] ,Interrupt 0 Enable bit 3" "Disabled,Enabled" bitfld.long 0x04 2. " [2] ,Interrupt 0 Enable bit 2" "Disabled,Enabled" bitfld.long 0x04 1. " [1] ,Interrupt 0 Enable bit 1" "Disabled,Enabled" bitfld.long 0x04 0. " [0] ,Interrupt 0 Enable bit 0" "Disabled,Enabled" line.long 0x08 "INT0ENABLE2,Interrupt Enable Register 2 for interrupts bits" bitfld.long 0x08 7. " INT0ENABLE2_[7] ,Interrupt 0 Enable bit 7" "Disabled,Enabled" bitfld.long 0x08 6. " [6] ,Interrupt 0 Enable bit 6" "Disabled,Enabled" bitfld.long 0x08 5. " [5] ,Interrupt 0 Enable bit 5" "Disabled,Enabled" bitfld.long 0x08 4. " [4] ,Interrupt 0 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x08 3. " [3] ,Interrupt 0 Enable bit 3" "Disabled,Enabled" bitfld.long 0x08 2. " [2] ,Interrupt 0 Enable bit 2" "Disabled,Enabled" bitfld.long 0x08 1. " [1] ,Interrupt 0 Enable bit 1" "Disabled,Enabled" bitfld.long 0x08 0. " [0] ,Interrupt 0 Enable bit 0" "Disabled,Enabled" textline "" line.long 0x0C "INT1ENABLE0,Interrupt Enable Register 0 for interrupts bits" bitfld.long 0x0C 31. " INT1ENABLE0_[31] ,Interrupt 1 Enable bit 31" "Disabled,Enabled" bitfld.long 0x0C 30. " [30] ,Interrupt 1 Enable bit 30" "Disabled,Enabled" bitfld.long 0x0C 29. " [29] ,Interrupt 1 Enable bit 29" "Disabled,Enabled" bitfld.long 0x0C 28. " [28] ,Interrupt 1 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x0C 27. " [27] ,Interrupt 1 Enable bit 27" "Disabled,Enabled" bitfld.long 0x0C 26. " [26] ,Interrupt 1 Enable bit 26" "Disabled,Enabled" bitfld.long 0x0C 25. " [25] ,Interrupt 1 Enable bit 25" "Disabled,Enabled" bitfld.long 0x0C 24. " [24] ,Interrupt 1 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x0C 23. " [23] ,Interrupt 1 Enable bit 23" "Disabled,Enabled" bitfld.long 0x0C 22. " [22] ,Interrupt 1 Enable bit 22" "Disabled,Enabled" bitfld.long 0x0C 21. " [21] ,Interrupt 1 Enable bit 21" "Disabled,Enabled" bitfld.long 0x0C 20. " [20] ,Interrupt 1 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x0C 19. " [19] ,Interrupt 1 Enable bit 19" "Disabled,Enabled" bitfld.long 0x0C 18. " [18] ,Interrupt 1 Enable bit 18" "Disabled,Enabled" bitfld.long 0x0C 17. " [17] ,Interrupt 1 Enable bit 17" "Disabled,Enabled" bitfld.long 0x0C 16. " [16] ,Interrupt 1 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x0C 15. " [15] ,Interrupt 1 Enable bit 15" "Disabled,Enabled" bitfld.long 0x0C 14. " [14] ,Interrupt 1 Enable bit 14" "Disabled,Enabled" bitfld.long 0x0C 13. " [13] ,Interrupt 1 Enable bit 13" "Disabled,Enabled" bitfld.long 0x0C 12. " [12] ,Interrupt 1 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x0C 11. " [11] ,Interrupt 1 Enable bit 11" "Disabled,Enabled" bitfld.long 0x0C 10. " [10] ,Interrupt 1 Enable bit 10" "Disabled,Enabled" bitfld.long 0x0C 9. " [9] ,Interrupt 1 Enable bit 9" "Disabled,Enabled" bitfld.long 0x0C 8. " [8] ,Interrupt 1 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x0C 7. " [7] ,Interrupt 1 Enable bit 7" "Disabled,Enabled" bitfld.long 0x0C 6. " [6] ,Interrupt 1 Enable bit 6" "Disabled,Enabled" bitfld.long 0x0C 5. " [5] ,Interrupt 1 Enable bit 5" "Disabled,Enabled" bitfld.long 0x0C 4. " [4] ,Interrupt 1 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x0C 3. " [3] ,Interrupt 1 Enable bit 3" "Disabled,Enabled" bitfld.long 0x0C 2. " [2] ,Interrupt 1 Enable bit 2" "Disabled,Enabled" bitfld.long 0x0C 1. " [1] ,Interrupt 1 Enable bit 1" "Disabled,Enabled" bitfld.long 0x0C 0. " [0] ,Interrupt 1 Enable bit 0" "Disabled,Enabled" line.long 0x10 "INT1ENABLE1,Interrupt Enable Register 1 for interrupts bits" bitfld.long 0x10 31. " INT1ENABLE1_[31] ,Interrupt 1 Enable bit 31" "Disabled,Enabled" bitfld.long 0x10 30. " [30] ,Interrupt 1 Enable bit 30" "Disabled,Enabled" bitfld.long 0x10 29. " [29] ,Interrupt 1 Enable bit 29" "Disabled,Enabled" bitfld.long 0x10 28. " [28] ,Interrupt 1 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x10 27. " [27] ,Interrupt 1 Enable bit 27" "Disabled,Enabled" bitfld.long 0x10 26. " [26] ,Interrupt 1 Enable bit 26" "Disabled,Enabled" bitfld.long 0x10 25. " [25] ,Interrupt 1 Enable bit 25" "Disabled,Enabled" bitfld.long 0x10 24. " [24] ,Interrupt 1 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x10 23. " [23] ,Interrupt 1 Enable bit 23" "Disabled,Enabled" bitfld.long 0x10 22. " [22] ,Interrupt 1 Enable bit 22" "Disabled,Enabled" bitfld.long 0x10 21. " [21] ,Interrupt 1 Enable bit 21" "Disabled,Enabled" bitfld.long 0x10 20. " [20] ,Interrupt 1 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x10 19. " [19] ,Interrupt 1 Enable bit 19" "Disabled,Enabled" bitfld.long 0x10 18. " [18] ,Interrupt 1 Enable bit 18" "Disabled,Enabled" bitfld.long 0x10 17. " [17] ,Interrupt 1 Enable bit 17" "Disabled,Enabled" bitfld.long 0x10 16. " [16] ,Interrupt 1 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x10 15. " [15] ,Interrupt 1 Enable bit 15" "Disabled,Enabled" bitfld.long 0x10 14. " [14] ,Interrupt 1 Enable bit 14" "Disabled,Enabled" bitfld.long 0x10 13. " [13] ,Interrupt 1 Enable bit 13" "Disabled,Enabled" bitfld.long 0x10 12. " [12] ,Interrupt 1 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x10 11. " [11] ,Interrupt 1 Enable bit 11" "Disabled,Enabled" bitfld.long 0x10 10. " [10] ,Interrupt 1 Enable bit 10" "Disabled,Enabled" bitfld.long 0x10 9. " [9] ,Interrupt 1 Enable bit 9" "Disabled,Enabled" bitfld.long 0x10 8. " [8] ,Interrupt 1 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x10 7. " [7] ,Interrupt 1 Enable bit 7" "Disabled,Enabled" bitfld.long 0x10 6. " [6] ,Interrupt 1 Enable bit 6" "Disabled,Enabled" bitfld.long 0x10 5. " [5] ,Interrupt 1 Enable bit 5" "Disabled,Enabled" bitfld.long 0x10 4. " [4] ,Interrupt 1 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x10 3. " [3] ,Interrupt 1 Enable bit 3" "Disabled,Enabled" bitfld.long 0x10 2. " [2] ,Interrupt 1 Enable bit 2" "Disabled,Enabled" bitfld.long 0x10 1. " [1] ,Interrupt 1 Enable bit 1" "Disabled,Enabled" bitfld.long 0x10 0. " [0] ,Interrupt 1 Enable bit 0" "Disabled,Enabled" line.long 0x14 "INT1ENABLE2,Interrupt Enable Register 2 for interrupts bits" bitfld.long 0x14 7. " INT1ENABLE2_[7] ,Interrupt 1 Enable bit 7" "Disabled,Enabled" bitfld.long 0x14 6. " [6] ,Interrupt 1 Enable bit 6" "Disabled,Enabled" bitfld.long 0x14 5. " [5] ,Interrupt 1 Enable bit 5" "Disabled,Enabled" bitfld.long 0x14 4. " [4] ,Interrupt 1 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x14 3. " [3] ,Interrupt 1 Enable bit 3" "Disabled,Enabled" bitfld.long 0x14 2. " [2] ,Interrupt 1 Enable bit 2" "Disabled,Enabled" bitfld.long 0x14 1. " [1] ,Interrupt 1 Enable bit 1" "Disabled,Enabled" bitfld.long 0x14 0. " [0] ,Interrupt 1 Enable bit 0" "Disabled,Enabled" textline "" line.long 0x18 "INTCLEAR0,Interrupt Clear Register 0 for interrupt bits" eventfld.long 0x18 31. " INTCLEAR0_[31] ,Interrupt Clear bit 31" "Not clear,Clear" eventfld.long 0x18 30. " [30] ,Interrupt Clear bit 30" "Not clear,Clear" eventfld.long 0x18 29. " [29] ,Interrupt Clear bit 29" "Not clear,Clear" eventfld.long 0x18 28. " [28] ,Interrupt Clear bit 28" "Not clear,Clear" textline " " eventfld.long 0x18 27. " [27] ,Interrupt Clear bit 27" "Not clear,Clear" eventfld.long 0x18 26. " [26] ,Interrupt Clear bit 26" "Not clear,Clear" eventfld.long 0x18 25. " [25] ,Interrupt Clear bit 25" "Not clear,Clear" eventfld.long 0x18 24. " [24] ,Interrupt Clear bit 24" "Not clear,Clear" textline " " eventfld.long 0x18 23. " [23] ,Interrupt Clear bit 23" "Not clear,Clear" eventfld.long 0x18 22. " [22] ,Interrupt Clear bit 22" "Not clear,Clear" eventfld.long 0x18 21. " [21] ,Interrupt Clear bit 21" "Not clear,Clear" eventfld.long 0x18 20. " [20] ,Interrupt Clear bit 20" "Not clear,Clear" textline " " eventfld.long 0x18 19. " [19] ,Interrupt Clear bit 19" "Not clear,Clear" eventfld.long 0x18 18. " [18] ,Interrupt Clear bit 18" "Not clear,Clear" eventfld.long 0x18 17. " [17] ,Interrupt Clear bit 17" "Not clear,Clear" eventfld.long 0x18 16. " [16] ,Interrupt Clear bit 16" "Not clear,Clear" textline " " eventfld.long 0x18 15. " [15] ,Interrupt Clear bit 15" "Not clear,Clear" eventfld.long 0x18 14. " [14] ,Interrupt Clear bit 14" "Not clear,Clear" eventfld.long 0x18 13. " [13] ,Interrupt Clear bit 13" "Not clear,Clear" eventfld.long 0x18 12. " [12] ,Interrupt Clear bit 12" "Not clear,Clear" textline " " eventfld.long 0x18 11. " [11] ,Interrupt Clear bit 11" "Not clear,Clear" eventfld.long 0x18 10. " [10] ,Interrupt Clear bit 10" "Not clear,Clear" eventfld.long 0x18 9. " [9] ,Interrupt Clear bit 9" "Not clear,Clear" eventfld.long 0x18 8. " [8] ,Interrupt Clear bit 8" "Not clear,Clear" textline " " eventfld.long 0x18 7. " [7] ,Interrupt Clear bit 7" "Not clear,Clear" eventfld.long 0x18 6. " [6] ,Interrupt Clear bit 6" "Not clear,Clear" eventfld.long 0x18 5. " [5] ,Interrupt Clear bit 5" "Not clear,Clear" eventfld.long 0x18 4. " [4] ,Interrupt Clear bit 4" "Not clear,Clear" textline " " eventfld.long 0x18 3. " [3] ,Interrupt Clear bit 3" "Not clear,Clear" eventfld.long 0x18 2. " [2] ,Interrupt Clear bit 2" "Not clear,Clear" eventfld.long 0x18 1. " [1] ,Interrupt Clear bit 1" "Not clear,Clear" eventfld.long 0x18 0. " [0] ,Interrupt Clear bit 0" "Not clear,Clear" line.long 0x1C "INTCLEAR1,Interrupt Clear Register 1 for interrupt bits" eventfld.long 0x1C 31. " INTCLEAR1_[31] ,Interrupt Clear bit 31" "Not clear,Clear" eventfld.long 0x1C 30. " [30] ,Interrupt Clear bit 30" "Not clear,Clear" eventfld.long 0x1C 29. " [29] ,Interrupt Clear bit 29" "Not clear,Clear" eventfld.long 0x1C 28. " [28] ,Interrupt Clear bit 28" "Not clear,Clear" textline " " eventfld.long 0x1C 27. " [27] ,Interrupt Clear bit 27" "Not clear,Clear" eventfld.long 0x1C 26. " [26] ,Interrupt Clear bit 26" "Not clear,Clear" eventfld.long 0x1C 25. " [25] ,Interrupt Clear bit 25" "Not clear,Clear" eventfld.long 0x1C 24. " [24] ,Interrupt Clear bit 24" "Not clear,Clear" textline " " eventfld.long 0x1C 23. " [23] ,Interrupt Clear bit 23" "Not clear,Clear" eventfld.long 0x1C 22. " [22] ,Interrupt Clear bit 22" "Not clear,Clear" eventfld.long 0x1C 21. " [21] ,Interrupt Clear bit 21" "Not clear,Clear" eventfld.long 0x1C 20. " [20] ,Interrupt Clear bit 20" "Not clear,Clear" textline " " eventfld.long 0x1C 19. " [19] ,Interrupt Clear bit 19" "Not clear,Clear" eventfld.long 0x1C 18. " [18] ,Interrupt Clear bit 18" "Not clear,Clear" eventfld.long 0x1C 17. " [17] ,Interrupt Clear bit 17" "Not clear,Clear" eventfld.long 0x1C 16. " [16] ,Interrupt Clear bit 16" "Not clear,Clear" textline " " eventfld.long 0x1C 15. " [15] ,Interrupt Clear bit 15" "Not clear,Clear" eventfld.long 0x1C 14. " [14] ,Interrupt Clear bit 14" "Not clear,Clear" eventfld.long 0x1C 13. " [13] ,Interrupt Clear bit 13" "Not clear,Clear" eventfld.long 0x1C 12. " [12] ,Interrupt Clear bit 12" "Not clear,Clear" textline " " eventfld.long 0x1C 11. " [11] ,Interrupt Clear bit 11" "Not clear,Clear" eventfld.long 0x1C 10. " [10] ,Interrupt Clear bit 10" "Not clear,Clear" eventfld.long 0x1C 9. " [9] ,Interrupt Clear bit 9" "Not clear,Clear" eventfld.long 0x1C 8. " [8] ,Interrupt Clear bit 8" "Not clear,Clear" textline " " eventfld.long 0x1C 7. " [7] ,Interrupt Clear bit 7" "Not clear,Clear" eventfld.long 0x1C 6. " [6] ,Interrupt Clear bit 6" "Not clear,Clear" eventfld.long 0x1C 5. " [5] ,Interrupt Clear bit 5" "Not clear,Clear" eventfld.long 0x1C 4. " [4] ,Interrupt Clear bit 4" "Not clear,Clear" textline " " eventfld.long 0x1C 3. " [3] ,Interrupt Clear bit 3" "Not clear,Clear" eventfld.long 0x1C 2. " [2] ,Interrupt Clear bit 2" "Not clear,Clear" eventfld.long 0x1C 1. " [1] ,Interrupt Clear bit 1" "Not clear,Clear" eventfld.long 0x1C 0. " [0] ,Interrupt Clear bit 0" "Not clear,Clear" line.long 0x20 "INTCLEAR2,Interrupt Clear Register 2 for interrupt bits" eventfld.long 0x20 7. " INTCLEAR2_[7] ,Interrupt Clear bit 7" "Not clear,Clear" eventfld.long 0x20 6. " [6] ,Interrupt Clear bit 6" "Not clear,Clear" eventfld.long 0x20 5. " [5] ,Interrupt Clear bit 5" "Not clear,Clear" eventfld.long 0x20 4. " [4] ,Interrupt Clear bit 4" "Not clear,Clear" textline " " eventfld.long 0x20 3. " [3] ,Interrupt Clear bit 3" "Not clear,Clear" eventfld.long 0x20 2. " [2] ,Interrupt Clear bit 2" "Not clear,Clear" eventfld.long 0x20 1. " [1] ,Interrupt Clear bit 1" "Not clear,Clear" eventfld.long 0x20 0. " [0] ,Interrupt Clear bit 0" "Not clear,Clear" textline "" line.long 0x24 "INTPRESET0,Interrupt Preset Register 1 for interrupt bits" eventfld.long 0x24 31. " INTPRESET0_[31] ,Interrupt Preset bit 31" "Not interrupt,Interrupt" eventfld.long 0x24 30. " [30] ,Interrupt Preset bit 30" "Not interrupt,Interrupt" eventfld.long 0x24 29. " [29] ,Interrupt Preset bit 29" "Not interrupt,Interrupt" eventfld.long 0x24 28. " [28] ,Interrupt Preset bit 28" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 27. " [27] ,Interrupt Preset bit 27" "Not interrupt,Interrupt" eventfld.long 0x24 26. " [26] ,Interrupt Preset bit 26" "Not interrupt,Interrupt" eventfld.long 0x24 25. " [25] ,Interrupt Preset bit 25" "Not interrupt,Interrupt" eventfld.long 0x24 24. " [24] ,Interrupt Preset bit 24" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 23. " [23] ,Interrupt Preset bit 23" "Not interrupt,Interrupt" eventfld.long 0x24 22. " [22] ,Interrupt Preset bit 22" "Not interrupt,Interrupt" eventfld.long 0x24 21. " [21] ,Interrupt Preset bit 21" "Not interrupt,Interrupt" eventfld.long 0x24 20. " [20] ,Interrupt Preset bit 20" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 19. " [19] ,Interrupt Preset bit 19" "Not interrupt,Interrupt" eventfld.long 0x24 18. " [18] ,Interrupt Preset bit 18" "Not interrupt,Interrupt" eventfld.long 0x24 17. " [17] ,Interrupt Preset bit 17" "Not interrupt,Interrupt" eventfld.long 0x24 16. " [16] ,Interrupt Preset bit 16" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 15. " [15] ,Interrupt Preset bit 15" "Not interrupt,Interrupt" eventfld.long 0x24 14. " [14] ,Interrupt Preset bit 14" "Not interrupt,Interrupt" eventfld.long 0x24 13. " [13] ,Interrupt Preset bit 13" "Not interrupt,Interrupt" eventfld.long 0x24 12. " [12] ,Interrupt Preset bit 12" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 11. " [11] ,Interrupt Preset bit 11" "Not interrupt,Interrupt" eventfld.long 0x24 10. " [10] ,Interrupt Preset bit 10" "Not interrupt,Interrupt" eventfld.long 0x24 9. " [9] ,Interrupt Preset bit 9" "Not interrupt,Interrupt" eventfld.long 0x24 8. " [8] ,Interrupt Preset bit 8" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 7. " [7] ,Interrupt Preset bit 7" "Not interrupt,Interrupt" eventfld.long 0x24 6. " [6] ,Interrupt Preset bit 6" "Not interrupt,Interrupt" eventfld.long 0x24 5. " [5] ,Interrupt Preset bit 5" "Not interrupt,Interrupt" eventfld.long 0x24 4. " [4] ,Interrupt Preset bit 4" "Not interrupt,Interrupt" textline " " eventfld.long 0x24 3. " [3] ,Interrupt Preset bit 3" "Not interrupt,Interrupt" eventfld.long 0x24 2. " [2] ,Interrupt Preset bit 2" "Not interrupt,Interrupt" eventfld.long 0x24 1. " [1] ,Interrupt Preset bit 1" "Not interrupt,Interrupt" eventfld.long 0x24 0. " [0] ,Interrupt Preset bit 0" "Not interrupt,Interrupt" line.long 0x28 "INTPRESET1,Interrupt Preset Register 1 for interrupt bits" eventfld.long 0x28 31. " INTPRESET1_[31] ,Interrupt Preset bit 31" "Not interrupt,Interrupt" eventfld.long 0x28 30. " [30] ,Interrupt Preset bit 30" "Not interrupt,Interrupt" eventfld.long 0x28 29. " [29] ,Interrupt Preset bit 29" "Not interrupt,Interrupt" eventfld.long 0x28 28. " [28] ,Interrupt Preset bit 28" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 27. " [27] ,Interrupt Preset bit 27" "Not interrupt,Interrupt" eventfld.long 0x28 26. " [26] ,Interrupt Preset bit 26" "Not interrupt,Interrupt" eventfld.long 0x28 25. " [25] ,Interrupt Preset bit 25" "Not interrupt,Interrupt" eventfld.long 0x28 24. " [24] ,Interrupt Preset bit 24" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 23. " [23] ,Interrupt Preset bit 23" "Not interrupt,Interrupt" eventfld.long 0x28 22. " [22] ,Interrupt Preset bit 22" "Not interrupt,Interrupt" eventfld.long 0x28 21. " [21] ,Interrupt Preset bit 21" "Not interrupt,Interrupt" eventfld.long 0x28 20. " [20] ,Interrupt Preset bit 20" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 19. " [19] ,Interrupt Preset bit 19" "Not interrupt,Interrupt" eventfld.long 0x28 18. " [18] ,Interrupt Preset bit 18" "Not interrupt,Interrupt" eventfld.long 0x28 17. " [17] ,Interrupt Preset bit 17" "Not interrupt,Interrupt" eventfld.long 0x28 16. " [16] ,Interrupt Preset bit 16" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 15. " [15] ,Interrupt Preset bit 15" "Not interrupt,Interrupt" eventfld.long 0x28 14. " [14] ,Interrupt Preset bit 14" "Not interrupt,Interrupt" eventfld.long 0x28 13. " [13] ,Interrupt Preset bit 13" "Not interrupt,Interrupt" eventfld.long 0x28 12. " [12] ,Interrupt Preset bit 12" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 11. " [11] ,Interrupt Preset bit 11" "Not interrupt,Interrupt" eventfld.long 0x28 10. " [10] ,Interrupt Preset bit 10" "Not interrupt,Interrupt" eventfld.long 0x28 9. " [9] ,Interrupt Preset bit 9" "Not interrupt,Interrupt" eventfld.long 0x28 8. " [8] ,Interrupt Preset bit 8" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 7. " [7] ,Interrupt Preset bit 7" "Not interrupt,Interrupt" eventfld.long 0x28 6. " [6] ,Interrupt Preset bit 6" "Not interrupt,Interrupt" eventfld.long 0x28 5. " [5] ,Interrupt Preset bit 5" "Not interrupt,Interrupt" eventfld.long 0x28 4. " [4] ,Interrupt Preset bit 4" "Not interrupt,Interrupt" textline " " eventfld.long 0x28 3. " [3] ,Interrupt Preset bit 3" "Not interrupt,Interrupt" eventfld.long 0x28 2. " [2] ,Interrupt Preset bit 2" "Not interrupt,Interrupt" eventfld.long 0x28 1. " [1] ,Interrupt Preset bit 1" "Not interrupt,Interrupt" eventfld.long 0x28 0. " [0] ,Interrupt Preset bit 0" "Not interrupt,Interrupt" line.long 0x2C "INTPRESET2,Interrupt Preset Register 2 for interrupt bits" eventfld.long 0x2C 7. " INTPRESET2_[7] ,Interrupt Preset bit 7" "Not interrupt,Interrupt" eventfld.long 0x2C 6. " [6] ,Interrupt Preset bit 6" "Not interrupt,Interrupt" eventfld.long 0x2C 5. " [5] ,Interrupt Preset bit 5" "Not interrupt,Interrupt" eventfld.long 0x2C 4. " [4] ,Interrupt Preset bit 4" "Not interrupt,Interrupt" textline " " eventfld.long 0x2C 3. " [3] ,Interrupt Preset bit 3" "Not interrupt,Interrupt" eventfld.long 0x2C 2. " [2] ,Interrupt Preset bit 2" "Not interrupt,Interrupt" eventfld.long 0x2C 1. " [1] ,Interrupt Preset bit 1" "Not interrupt,Interrupt" eventfld.long 0x2C 0. " [0] ,Interrupt Preset bit 0" "Not interrupt,Interrupt" tree.end width 15. group.long 0x400++0x03 line.long 0x00 "FIFO,FIFO" button "FIFO" "d (ad:0x3A030000+0x400)--(ad:0x3A030000+0x4FF) /long" group.long 0x500++0x03 line.long 0x00 "CONTROL,Message Buffer Control" bitfld.long 0x00 31. " BLOCK_ON_FATAL ,Suppress pending signal when fatal error was detected" "No error,Error" bitfld.long 0x00 2. " R1BUF_BACKPRESSURE_ENABLE ,Enable backpressure when read buffer 1 is running full" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " R0BUF_BACKPRESSURE_ENABLE ,Enable backpressure when read buffer 0 is running full" "Disabled,Enabled" rgroup.long 0x504++0x03 line.long 0x00 "STATUS,Message Buffer Status" bitfld.long 0x00 6. " WDG_TIMEOUT ,Watchdog timeout" "Not timeout,Timeout" bitfld.long 0x00 5. " WRBUF_EMPTY ,Write buffer is empty" "Not empty,Empty" textline " " bitfld.long 0x00 4. " WRBUF_FULL ,Write buffer is full" "Not full,Full" bitfld.long 0x00 3. " R1BUF_EMPTY ,Read buffer 1 is empty" "Not empty,Empty" textline " " bitfld.long 0x00 2. " R1BUF_FULL ,Read buffer 1 is full" "Not full,Full" bitfld.long 0x00 1. " R0BUF_EMPTY ,Read buffer 0 is empty" "Not empty,Empty" textline " " bitfld.long 0x00 0. " R0BUF_FULL ,Read buffer 0 is full" "Not full,Full" group.long 0x508++0x0B line.long 0x00 "CLEAR,Message Buffer Clear" eventfld.long 0x00 2. " R1BUF_CLEAR ,Writing a '1' clears read buffer 1" "Not clear,Clear" eventfld.long 0x00 1. " R0BUF_CLEAR ,Writing a '1' clears read buffer 0" "Not clear,Clear" textline " " eventfld.long 0x00 0. " WRBUF_CLEAR ,Writing a '1' clears write buffer" "Not clear,Clear" line.long 0x04 "DMA_CONTROL,DMA Control" bitfld.long 0x04 24.--25. " DMA2_MODE ,Dma2 mode" "Previous,Local,Both," bitfld.long 0x04 20.--21. " DMA1_MODE ,Dma1 mode" "Previous,Local,Both," textline " " bitfld.long 0x04 16.--17. " DMA0_MODE ,Dma0 mode" "Previous,Local,Both," bitfld.long 0x04 10. " R1BUF_DMA_ENABLE ,Enable DMA for read buffer 1" "Disabled,Enabled" textline " " bitfld.long 0x04 6. " R0BUF_DMA_ENABLE ,Enable DMA for read buffer 0" "Disabled,Enabled" bitfld.long 0x04 4.--5. " R0BUF_DMA_PORT ,DMA port number for read buffer 0" "0,1,2,3" textline " " bitfld.long 0x04 2. " WRBUF_DMA_ENABLE ,Enable DMA for write buffer" "Disabled,Enabled" bitfld.long 0x04 0.--1. " WRBUF_DMA_PORT ,DMA port number for write buffer" "0,1,2,3" line.long 0x08 "WATCHDOG_LOAD,Watchdog counter preset value" textline "" width 39. group.long 0x600++0x0B line.long 0x00 "RX0_I2C_OUTBOUND_JOB_SPEC_STATUS,RX0_I2C_Outbound_Job_Spec_Status" eventfld.long 0x00 31. " RX0_I2C_OUTBOUND_JOB_SPEC_CLEAR ,RX0_I2C_Outbound_Job_Spec_Clear" "Not clear,Clear" textline " " rbitfld.long 0x00 0. " RX0_I2C_OUTBOUND_JOB_SPEC_BUSY ,RX0_I2C_Outbound_Job_Spec_Busy" "Not busy,Busy" line.long 0x04 "RX0_I2C_OUTBOUND_JOB_SPEC_DATA_LOW,RX0_I2C_Outbound_Job_Spec_Data_Low" line.long 0x08 "RX0_I2C_OUTBOUND_JOB_SPEC_DATA_HIGH,RX0_I2C_Outbound_Job_Spec_Data_High" rgroup.long 0x60C++0x0B line.long 0x00 "RX0_I2C_INBOUND_JOB_SPEC_STATUS,RX0_I2C_Inbound_Job_Spec_Status" bitfld.long 0x00 0. " RX0_I2C_INBOUND_JOB_SPEC_VALID ,RX0_I2C_Inbound_Job_Spec_Valid" "No,Yes" line.long 0x04 "RX0_I2C_INBOUND_JOB_SPEC_DATA_LOW,RX0_I2C_Inbound_Job_Spec_Data_Low" line.long 0x08 "RX0_I2C_INBOUND_JOB_SPEC_DATA_HIGH,RX0_I2C_Inbound_Job_Spec_Data_High" group.long 0x618++0x0B line.long 0x00 "RX0_I2C_INBOUND_JOB_SPEC_ERROR,RX0_I2C_Inbound_Job_Spec_Error" bitfld.long 0x00 31. " RX0_I2C_INBOUND_JOB_SPEC_ERROR ,RX0_I2C_Inbound_Job_Spec_Error" "No error,Error" line.long 0x04 "RX0_I2C_OUTBOUND_STATUS,RX0_I2C_Outbound_Status" eventfld.long 0x04 31. " RX0_I2C_OUTBOUND_STATUS_CLEAR ,RX0_I2C_Outbound_Status_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX0_I2C_OUTBOUND_STATUS_BUSY ,RX0_I2C_Outbound_Status_Busy" "Not busy,Busy" line.long 0x08 "RX0_I2C_OUTBOUND_STATUS_DATA,RX0_I2C_Outbound_Status_Data" bitfld.long 0x08 3. " RX0_I2C_OUTBOUND_STATUS_ALOST_DETECTED ,RX0_I2C_Outbound_Status_Alost_Detected" "Not detected,Detected" textline " " bitfld.long 0x08 2. " RX0_I2C_OUTBOUND_STATUS_NACK_DETECTED ,RX0_I2C_Outbound_Status_Nack_Detected" "Not detected,Detected" textline " " bitfld.long 0x08 1. " RX0_I2C_OUTBOUND_STATUS_JOB_CACC ,RX0_I2C_Outbound_Status_Job_Cacc" "0,1" textline " " bitfld.long 0x08 0. " RX0_I2C_OUTBOUND_STATUS_JOB_DONE ,RX0_I2C_Outbound_Status_Job_Done" "0,1" rgroup.long 0x624++0x03 line.long 0x00 "RX0_I2C_INBOUND_STATUS,RX0_I2C_Inbound_Status" bitfld.long 0x00 0. " RX0_I2C_INBOUND_STATUS_VALID ,RX0_I2C_Inbound_Status_Valid" "No,Yes" group.long 0x628++0x0B line.long 0x00 "RX0_I2C_INBOUND_STATUS_DATA,RX0_I2C_Inbound_Status_Data" bitfld.long 0x00 31. " RX0_I2C_INBOUND_STATUS_ERROR ,RX0_I2C_Inbound_Status_Error" "No error,Error" textline " " rbitfld.long 0x00 3. " RX0_I2C_INBOUND_STATUS_ALOST_DETECTED ,RX0_I2C_Inbound_Status_Alost_detected" "Not detected,Detected" textline " " rbitfld.long 0x00 2. " RX0_I2C_INBOUND_STATUS_NACK_DETECTED ,RX0_I2C_Inbound_Status_Nack_detected" "Not detected,Detected" textline " " rbitfld.long 0x00 1. " RX0_I2C_INBOUND_STATUS_JOB_CACC ,RX0_I2C_Inbound_Status_Job_cacc" "0,1" textline " " rbitfld.long 0x00 0. " RX0_I2C_INBOUND_STATUS_JOB_DONE ,RX0_I2C_Inbound_Status_Job_done" "0,1" line.long 0x04 "RX0_I2C_OUTBOUND_READ_RESPONSE_STATUS,RX0_I2C_Outbound_Read_Response_Status" eventfld.long 0x04 31. " RX0_I2C_OUTBOUND_READ_RESPONSE_CLEAR ,RX0_I2C_Outbound_Read_Response_Clear" "Not clear,Clear" textline " " bitfld.long 0x04 0. " RX0_I2C_OUTBOUND_READ_RESPONSE_BUSY ,RX0_I2C_Outbound_Read_Response_Busy" "Not busy,Busy" line.long 0x08 "RX0_I2C_OUTBOUND_READ_RESPONSE_DATA,RX0_I2C_Outbound_Read_Response_Data" hexmask.long.byte 0x08 0.--7. 1. " RX0_I2C_OUTBOUND_READ_RESPONSE_DATA ,RX0_I2C_Outbound_Read_Response_Data" rgroup.long 0x634++0x03 line.long 0x00 "RX0_I2C_INBOUND_READ_RESPONSE_STATUS,RX0_I2C_Inbound_Read_Response_Status" bitfld.long 0x00 0. " RX0_I2C_INBOUND_READ_RESPONSE_VALID ,RX0_I2C_Inbound_Read_Response_Valid" "No,Yes" group.long 0x638++0x0F line.long 0x00 "RX0_I2C_INBOUND_READ_RESPONSE_DATA,RX0_I2C_Inbound_Read_Response_Data" bitfld.long 0x00 31. " RX0_I2C_INBOUND_READ_RESPONSE_ERROR ,RX0_I2C_Inbound_Read_Response_Error" "No error,Error" textline " " rbitfld.long 0x00 8.--10. " RX0_I2C_INBOUND_READ_RESPONSE_DATA_NUM ,RX0_I2C_Inbound_Read_Response_Data_Num" "0,1,2,3,4,5,6,7" textline " " hexmask.long.byte 0x00 0.--7. 1. " RX0_I2C_INBOUND_READ_RESPONSE_DATA ,RX0_I2C_Inbound_Read_Response_Data" line.long 0x04 "RX1_I2C_OUTBOUND_JOB_SPEC_STATUS,RX1_I2C_Outbound_Job_Spec_Status" eventfld.long 0x04 31. " RX1_I2C_OUTBOUND_JOB_SPEC_CLEAR ,RX1_I2C_Outbound_Job_Spec_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX1_I2C_OUTBOUND_JOB_SPEC_BUSY ,RX1_I2C_Outbound_Job_Spec_Busy" "Not busy,Busy" line.long 0x08 "RX1_I2C_OUTBOUND_JOB_SPEC_DATA_LOW,RX1_I2C_Outbound_Job_Spec_Data_Low" line.long 0x0C "RX1_I2C_OUTBOUND_JOB_SPEC_DATA_HIGH,RX1_I2C_Outbound_Job_Spec_Data_High" rgroup.long 0x648++0x0B line.long 0x00 "RX1_I2C_INBOUND_JOB_SPEC_STATUS,RX1_I2C_Inbound_Job_Spec_Status" bitfld.long 0x00 0. " RX1_I2C_INBOUND_JOB_SPEC_VALID ,RX1_I2C_Inbound_Job_Spec_Valid" "No,Yes" line.long 0x04 "RX1_I2C_INBOUND_JOB_SPEC_DATA_LOW,RX1_I2C_Inbound_Job_Spec_Data_Low" line.long 0x08 "RX1_I2C_INBOUND_JOB_SPEC_DATA_HIGH,RX1_I2C_Inbound_Job_Spec_Data_High" group.long 0x654++0x0B line.long 0x00 "RX1_I2C_INBOUND_JOB_SPEC_ERROR,RX1_I2C_Inbound_Job_Spec_Error" bitfld.long 0x00 31. " RX1_I2C_INBOUND_JOB_SPEC_ERROR ,RX1_I2C_Inbound_Job_Spec_Error" "No error,Error" line.long 0x04 "RX1_I2C_OUTBOUND_STATUS,RX1_I2C_Outbound_Status" eventfld.long 0x04 31. " RX1_I2C_OUTBOUND_STATUS_CLEAR ,RX1_I2C_Outbound_Status_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX1_I2C_OUTBOUND_STATUS_BUSY ,RX1_I2C_Outbound_Status_Busy" "Not busy,Busy" line.long 0x08 "RX1_I2C_OUTBOUND_STATUS_DATA,RX1_I2C_Outbound_Status_Data" bitfld.long 0x08 3. " RX1_I2C_OUTBOUND_STATUS_ALOST_DETECTED ,RX1_I2C_Outbound_Status_Alost_Detected" "Not detected,Detected" textline " " bitfld.long 0x08 2. " RX1_I2C_OUTBOUND_STATUS_NACK_DETECTED ,RX1_I2C_Outbound_Status_Nack_Detected" "Not detected,Detected" textline " " bitfld.long 0x08 1. " RX1_I2C_OUTBOUND_STATUS_JOB_CACC ,RX1_I2C_Outbound_Status_Job_Cacc" "0,1" textline " " bitfld.long 0x08 0. " RX1_I2C_OUTBOUND_STATUS_JOB_DONE ,RX1_I2C_Outbound_Status_Job_Done" "0,1" rgroup.long 0x660++0x03 line.long 0x00 "RX1_I2C_INBOUND_STATUS,RX1_I2C_Inbound_Status" bitfld.long 0x00 0. " RX1_I2C_INBOUND_STATUS_VALID ,RX1_I2C_Inbound_Status_Valid" "No,Yes" group.long 0x664++0x0B line.long 0x00 "RX1_I2C_INBOUND_STATUS_DATA,RX1_I2C_Inbound_Status_Data" bitfld.long 0x00 31. " RX1_I2C_INBOUND_STATUS_ERROR ,RX1_I2C_Inbound_Status_Error" "No error,Error" textline " " rbitfld.long 0x00 3. " RX1_I2C_INBOUND_STATUS_ALOST_DETECTED ,RX1_I2C_Inbound_Status_Alost_detected" "Not detected,Detected" textline " " bitfld.long 0x00 2. " RX1_I2C_INBOUND_STATUS_NACK_DETECTED ,RX1_I2C_Inbound_Status_Nack_detected" "Not detected,Detected" textline " " rbitfld.long 0x00 1. " RX1_I2C_INBOUND_STATUS_JOB_CACC ,RX1_I2C_Inbound_Status_Job_cacc" "0,1" textline " " bitfld.long 0x00 0. " RX1_I2C_INBOUND_STATUS_JOB_DONE ,RX1_I2C_Inbound_Status_Job_done" "0,1" line.long 0x04 "RX1_I2C_OUTBOUND_READ_RESPONSE_STATUS,RX1_I2C_Outbound_Read_Response_Status" eventfld.long 0x04 31. " RX1_I2C_OUTBOUND_READ_RESPONSE_CLEAR ,RX1_I2C_Outbound_Read_Response_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX1_I2C_OUTBOUND_READ_RESPONSE_BUSY ,RX1_I2C_Outbound_Read_Response_Busy" "Not busy,Busy" line.long 0x08 "RX1_I2C_OUTBOUND_READ_RESPONSE_DATA,RX1_I2C_Outbound_Read_Response_Data" hexmask.long.byte 0x08 0.--7. 1. " RX1_I2C_OUTBOUND_READ_RESPONSE_DATA ,RX1_I2C_Outbound_Read_Response_Data" rgroup.long 0x670++0x03 line.long 0x00 "RX1_I2C_INBOUND_READ_RESPONSE_STATUS,RX1_I2C_Inbound_Read_Response_Status" bitfld.long 0x00 0. " RX1_I2C_INBOUND_READ_RESPONSE_VALID ,RX1_I2C_Inbound_Read_Response_Valid" "No,Yes" group.long 0x674++0x0B line.long 0x00 "RX1_I2C_INBOUND_READ_RESPONSE_DATA,RX1_I2C_Inbound_Read_Response_Data" bitfld.long 0x00 31. " RX1_I2C_INBOUND_READ_RESPONSE_ERROR ,RX1_I2C_Inbound_Read_Response_Error" "No error,Error" textline " " rbitfld.long 0x00 8.--10. " RX1_I2C_INBOUND_READ_RESPONSE_DATA_NUM ,RX1_I2C_Inbound_Read_Response_Data_Num" "0,1,2,3,4,5,6,7" textline " " hexmask.long.byte 0x00 0.--7. 1. " RX1_I2C_INBOUND_READ_RESPONSE_DATA ,RX1_I2C_Inbound_Read_Response_Data" line.long 0x04 "RX0_REMOTE_CONTROLLER_OUTBOUND_STATUS,RX0_Remote_Controller_Outbound_Status" eventfld.long 0x04 31. " RX0_REMOTE_CONTROLLER_OUTBOUND_CLEAR ,RX0_Remote_Controller_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX0_REMOTE_CONTROLLER_OUTBOUND_BUSY ,RX0_Remote_Controller_Outbound_Busy" "Not busy,Busy" line.long 0x08 "RX0_REMOTE_CONTROLLER_OUTBOUND_DATA,RX0_Remote_Controller_Outbound_Data" hexmask.long.byte 0x08 8.--15. 1. " RX0_REMOTE_CONTROLLER_OUTBOUND_DATA ,RX0_Remote_Controller_Outbound_Data" textline " " bitfld.long 0x08 7. " RX0_REMOTE_CONTROLLER_OUTBOUND_RW ,RX0_Remote_Controller_Outbound_RW" "0,1" textline " " hexmask.long.byte 0x08 0.--6. 1. " RX0_REMOTE_CONTROLLER_OUTBOUND_ADDRESS ,RX0_Remote_Controller_Outbound_Address" rgroup.long 0x680++0x03 line.long 0x00 "RX0_REMOTE_CONTROLLER_INBOUND_STATUS,RX0_Remote_Controller_Inbound_Status" bitfld.long 0x00 0. " RX0_REMOTE_CONTROLLER_INBOUND_VALID ,RX0_Remote_Controller_Inbound_Valid" "No,Yes" group.long 0x684++0x03 line.long 0x00 "RX0_REMOTE_CONTROLLER_INBOUND_DATA,RX0_Remote_Controller_Inbound_Data" rbitfld.long 0x00 31. " RX0_REMOTE_CONTROLLER_INBOUND_ERROR ,RX0_Remote_Controller_Inbound_Error" "No error,Error" textline " " hexmask.long.byte 0x00 0.--7. 1. " RX0_REMOTE_CONTROLLER_INBOUND_RESPONSE_DATA ,RX0_Remote_Controller_Inbound_Response_Data" rgroup.long 0x688++0x03 line.long 0x00 "RX0_REMOTE_SERVICE_INBOUND_STATUS,RX0_Remote_Service_Inbound_Status" bitfld.long 0x00 0. " RX0_REMOTE_SERVICE_INBOUND_VALID ,RX0_Remote_Service_Inbound_Valid" "No,Yes" group.long 0x68C++0x1B line.long 0x00 "RX0_REMOTE_SERVICE_INBOUND_DATA,RX0_Remote_Service_Inbound_Data" bitfld.long 0x00 31. " RX0_REMOTE_SERVICE_INBOUND_ERROR ,RX0_Remote_Service_Inbound_Error" "No error,Error" textline " " hexmask.long.byte 0x00 8.--15. 1. " RX0_REMOTE_SERVICE_INBOUND_DATA ,RX0_Remote_Service_Inbound_Data" textline " " bitfld.long 0x00 7. " RX0_REMOTE_SERVICE_INBOUND_RW ,RX0_Remote_Service_Inbound_RW" "0,1" textline " " hexmask.long.byte 0x00 0.--6. 1. " RX0_REMOTE_SERVICE_INBOUND_ADDRESS ,RX0_Remote_Service_Inbound_Address" line.long 0x04 "RX0_REMOTE_SERVICE_OUTBOUND_STATUS,RX0_Remote_Service_Outbound_Status" eventfld.long 0x04 31. " RX0_REMOTE_SERVICE_OUTBOUND_CLEAR ,RX0_Remote_Service_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX0_REMOTE_SERVICE_OUTBOUND_BUSY ,RX0_Remote_Service_Outbound_Busy" "Not busy,Busy" line.long 0x08 "RX0_REMOTE_SERVICE_OUTBOUND_DATA,RX0_Remote_Service_Outbound_Data" hexmask.long.byte 0x08 0.--7. 1. " RX0_REMOTE_SERVICE_OUTBOUND_READ_RESPONSE_DATA ,RX0_Remote_Service_Outbound_Read_Response_Data" line.long 0x0C "RX0_REMOTE_COMMAND_OUTBOUND_STATUS,RX0_Remote_Command_Outbound_Status" eventfld.long 0x0C 31. " RX0_REMOTE_COMMAND_OUTBOUND_CLEAR ,RX0_Remote_Command_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x0C 0. " RX0_REMOTE_COMMAND_OUTBOUND_BUSY ,RX0_Remote_Command_Outbound_Busy" "Not busy,Busy" line.long 0x10 "RX0_REMOTE_COMMAND_OUTBOUND_DATA,RX0_Remote_Command_Outbound_Data" bitfld.long 0x10 3. " RX0_REMOTE_COMMAND_OUTBOUND_JOB_CANCEL ,RX0_Remote_Command_Outbound_Job_Cancel" "0,1" textline " " bitfld.long 0x10 2. " RX0_REMOTE_COMMAND_OUTBOUND_CLEAR_TICKET_COUNTER ,RX0_Remote_Command_Outbound_Clear_Ticket_Counter" "Not clear,Clear" textline " " bitfld.long 0x10 1. " RX0_REMOTE_COMMAND_OUTBOUND_REALIGN ,RX0_Remote_Command_Outbound_Realign" "No,Yes" textline " " bitfld.long 0x10 0. " RX0_REMOTE_COMMAND_OUTBOUND_SOFT_RESET ,RX0_Remote_Command_Outbound_Soft_Reset" "No reset,Reset" line.long 0x14 "RX1_REMOTE_CONTROLLER_OUTBOUND_STATUS,RX1_Remote_Controller_Outbound_Status" eventfld.long 0x14 31. " RX1_REMOTE_CONTROLLER_OUTBOUND_CLEAR ,RX1_Remote_Controller_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x14 0. " RX1_REMOTE_CONTROLLER_OUTBOUND_BUSY ,RX1_Remote_Controller_Outbound_Busy" "Not busy,Busy" line.long 0x18 "RX1_REMOTE_CONTROLLER_OUTBOUND_DATA,RX1_Remote_Controller_Outbound_Data" hexmask.long.byte 0x18 8.--15. 1. " RX1_REMOTE_CONTROLLER_OUTBOUND_DATA ,RX1_Remote_Controller_Outbound_Data" textline " " bitfld.long 0x18 7. " RX1_REMOTE_CONTROLLER_OUTBOUND_RW ,RX1_Remote_Controller_Outbound_RW" "0,1" textline " " hexmask.long.byte 0x18 0.--6. 1. " RX1_REMOTE_CONTROLLER_OUTBOUND_ADDRESS ,RX1_Remote_Controller_Outbound_Address" rgroup.long 0x6A8++0x03 line.long 0x00 "RX1_REMOTE_CONTROLLER_INBOUND_STATUS,RX1_Remote_Controller_Inbound_Status" bitfld.long 0x00 0. " RX1_REMOTE_CONTROLLER_INBOUND_VALID ,RX1_Remote_Controller_Inbound_Valid" "No,Yes" group.long 0x6AC++0x03 line.long 0x00 "RX1_REMOTE_CONTROLLER_INBOUND_DATA,RX1_Remote_Controller_Inbound_Data" bitfld.long 0x00 31. " RX1_REMOTE_CONTROLLER_INBOUND_ERROR ,RX1_Remote_Controller_Inbound_Error" "No error,Error" textline " " hexmask.long.byte 0x00 0.--7. 1. " RX1_REMOTE_CONTROLLER_INBOUND_RESPONSE_DATA ,RX1_Remote_Controller_Inbound_Response_Data" rgroup.long 0x6B0++0x03 line.long 0x00 "RX1_REMOTE_SERVICE_INBOUND_STATUS,RX1_Remote_Service_Inbound_Status" bitfld.long 0x00 0. " RX1_REMOTE_SERVICE_INBOUND_VALID ,RX1_Remote_Service_Inbound_Valid" "No,Yes" group.long 0x6B4++0x13 line.long 0x00 "RX1_REMOTE_SERVICE_INBOUND_DATA,RX1_Remote_Service_Inbound_Data" bitfld.long 0x00 31. " RX1_REMOTE_SERVICE_INBOUND_ERROR ,RX1_Remote_Service_Inbound_Error" "No error,Error" textline " " hexmask.long.byte 0x00 8.--15. 1. " RX1_REMOTE_SERVICE_INBOUND_DATA ,RX1_Remote_Service_Inbound_Data" textline " " bitfld.long 0x00 7. " RX1_REMOTE_SERVICE_INBOUND_RW ,RX1_Remote_Service_Inbound_RW" "0,1" textline " " hexmask.long.byte 0x00 0.--6. 1. " RX1_REMOTE_SERVICE_INBOUND_ADDRESS ,RX1_Remote_Service_Inbound_Address" line.long 0x04 "RX1_REMOTE_SERVICE_OUTBOUND_STATUS,RX1_Remote_Service_Outbound_Status" eventfld.long 0x04 31. " RX1_REMOTE_SERVICE_OUTBOUND_CLEAR ,RX1_Remote_Service_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x04 0. " RX1_REMOTE_SERVICE_OUTBOUND_BUSY ,RX1_Remote_Service_Outbound_Busy" "Not busy,Busy" line.long 0x08 "RX1_REMOTE_SERVICE_OUTBOUND_DATA,RX1_Remote_Service_Outbound_Data" hexmask.long.byte 0x08 0.--7. 1. " RX1_REMOTE_SERVICE_OUTBOUND_READ_RESPONSE_DATA ,RX1_Remote_Service_Outbound_Read_Response_Data" line.long 0x0C "RX1_REMOTE_COMMAND_OUTBOUND_STATUS,RX1_Remote_Command_Outbound_Status" eventfld.long 0x0C 31. " RX1_REMOTE_COMMAND_OUTBOUND_CLEAR ,RX1_Remote_Command_Outbound_Clear" "Not clear,Clear" textline " " rbitfld.long 0x0C 0. " RX1_REMOTE_COMMAND_OUTBOUND_BUSY ,RX1_Remote_Command_Outbound_Busy" "Not busy,Busy" line.long 0x10 "RX1_REMOTE_COMMAND_OUTBOUND_DATA,RX1_Remote_Command_Outbound_Data" bitfld.long 0x10 2. " RX1_REMOTE_COMMAND_OUTBOUND_CLEAR_TICKET_COUNTER ,RX1_Remote_Command_Outbound_Clear_Ticket_Counter" "Not clear,Clear" textline " " bitfld.long 0x10 1. " RX1_REMOTE_COMMAND_OUTBOUND_REALIGN ,RX1_Remote_Command_Outbound_Realign" "No,Yes" textline " " bitfld.long 0x10 0. " RX1_REMOTE_COMMAND_OUTBOUND_SOFT_RESET ,RX1_Remote_Command_Outbound_Soft_Reset" "No reset,Reset" width 12. tree.end tree.end tree "APIX_RX" base ad:0x3A000000 width 33. group.long 0x00++0x07 line.long 0x00 "RX_ANALOG_CFG,Configuration for analog macro" bitfld.long 0x00 0.--5. " UPAMPL ,Defines the amplitude of the RX upstream driver" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x04 "CDR_MODE,Cdr mode" bitfld.long 0x04 2.--5. " CDR_COUNTER_DEPTH ,CDR counter depth" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" group.long 0x100++0x1F line.long 0x00 "SWRESET,Resets APIX IP core" bitfld.long 0x00 0. " CFG_VALID ,cfg_valid" "Core in reset,Core enabled" line.long 0x04 "APIXMODE,General configuration register" bitfld.long 0x04 1. " APIX_RX0_RX1 ,Selects the RX device number" "RX0,RX1" bitfld.long 0x04 0. " APIX_MODE ,Apix mode" "APIX1,APIX2" line.long 0x08 "LINKCFG,Configuration of different toplevel link functions" bitfld.long 0x08 8.--10. " HDCP_TARGET_SEL ,Selects HDCP support data target" "V000 TX2-IF RX0,V001 TX2-IF RX1,V010 TX1-IF RX0,V011 TX1-IF RX1,V100 TX0-IF RX0,V101 TX0-IF RX1,," bitfld.long 0x08 4. " PIXCH1_PIXELFIFO_PATH_EN ,Enable the channel 1 pixel stream to the small PixelFIFO" "Disabled,Enabled" textline " " bitfld.long 0x08 1. " PIXCH0_APIX2LOOPTHROUGH_PATH_EN ,Enable the channel 0 pixel stream to theapix2 loop through output" "Disabled,Enabled" bitfld.long 0x08 0. " PIXCH0_PIXELFIFO_PATH_EN ,Enable the channel 0 pixel stream to thesmall PixelFIFO" "Disable,Enabled" line.long 0x0C "CH0UNPACKER_COLORCOMPONENTBITS,Color component size of outgoing pixel stream channel 0" bitfld.long 0x0C 24.--27. " CH0COMPONENTBITSRED ,Number of red bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x0C 16.--19. " CH0COMPONENTBITSGREEN ,Number of green bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x0C 8.--11. " CH0COMPONENTBITSBLUE ,Number of blue bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x10 "CH0UNPACKER_COLORCOMPONENTSHIFT,Color component offset of outgoing pixel stream channel 0" bitfld.long 0x10 24.--28. " CH0COMPONENTSHIFTRED ,Shift position of red bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x10 16.--20. " CH0COMPONENTSHIFTGREEN ,Shift position of green bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x10 8.--12. " CH0COMPONENTSHIFTBLUE ,Shift position of blue bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" line.long 0x14 "CH1UNPACKER_COLORCOMPONENTBITS,Color component size of outgoing pixel stream channel 1" bitfld.long 0x14 24.--27. " CH1COMPONENTBITSRED ,Number of red bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x14 16.--19. " CH1COMPONENTBITSGREEN ,Number of green bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x14 8.--11. " CH1COMPONENTBITSBLUE ,Number of blue bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x18 "CH1UNPACKER_COLORCOMPONENTSHIFT,Color component offset of outgoing pixel stream channel 1" bitfld.long 0x18 24.--28. " CH1COMPONENTSHIFTRED ,Component Shift Red" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" bitfld.long 0x18 16.--20. " CH1COMPONENTSHIFTGREEN ,Component Shift Green" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline " " bitfld.long 0x18 8.--12. " CH1COMPONENTSHIFTBLUE ,Component Shift Blue" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" textline "" width 18. line.long 0x1C "APIX12_CFG_0,Config for Inova bytes 04_03_02_01 for APIX1 and APIX2 mode" bitfld.long 0x1C 15. " AGCAUTOCALCOFF ,AGC coefficient auto calculation" "Yes,No" bitfld.long 0x1C 14. " FIRAUTOCALCOFF ,Enable auto calculation of FIR coefficients for DFE" "Yes,No" textline " " bitfld.long 0x1C 8.--9. " DOWNBW ,[1:0] downstream bandwidth" ",M500mode,G1mode,G3mode" group.long 0x120++0x03 line.long 0x00 "APIX12_CFG_1,Config for Inova bytes 08_07_06_05 for APIX1 and APIX2 mode" bitfld.long 0x00 22. " FIRSIGNUM2 ,Defines the signum of FIR coefficient 2" "Negative,Positive" bitfld.long 0x00 16.--21. " FIRCOEFF2 ,Defines the FIR coefficient 2" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x00 14. " FIRSIGNUM1 ,Defines the signum of FIR coefficient 1" "Negative,Positive" bitfld.long 0x00 8.--13. " FIRCOEFF1 ,Defines the FIR coefficient 1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x00 6. " FIRSIGNUM0 ,Defines the signum of FIR coefficient 0" "Negative,Positive" bitfld.long 0x00 0.--5. " FIRCOEFF0 ,Defines the FIR coefficient 0" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" if (((per.l(ad:0x3A000000+0x104))&0x01)==0x01) group.long 0x124++0x03 line.long 0x00 "APIX12_CFG_2,Config for Inova bytes 0C_0B_0A_09 for APIX1 and APIX2 mode" bitfld.long 0x00 23. " WATCHDOGDFE ,Watchdog for restart of DFE Decision Feedback Equalizer algorithm" "Disabled,Enabled" bitfld.long 0x00 16.--17. " UPSERIALBW ,Upstream serial bandwidth" "APIX2_fast 187.5 Mbit/s,,APIX2_slow 62.5 Mbit/s," textline " " hexmask.long.byte 0x00 8.--14. 1. " AGCCOEFF ,Defines the AGC coefficient" else group.long 0x124++0x03 line.long 0x00 "APIX12_CFG_2,Config for Inova bytes 0C_0B_0A_09 for APIX1 and APIX2 mode" bitfld.long 0x00 23. " WATCHDOGDFE ,Watchdog for restart of DFE Decision Feedback Equalizer algorithm" "Disabled,Enabled" bitfld.long 0x00 16.--17. " UPSERIALBW ,Upstream serial bandwidth" ",APIX1_fast 62.5 Mbit/s,,APIX1_slow 31.25 Mbit/s" textline " " hexmask.long.byte 0x00 8.--14. 1. " AGCCOEFF ,Defines the AGC coefficient" endif group.long 0x128++0x03 line.long 0x00 "APIX12_CFG_3,Config for Inova bytes 0F_0E_0D for APIX1 and APIX2 mode" bitfld.long 0x00 21. " AUDIOBW ,Audio bandwidth" "Ordinary bandwidth,High bandwidth" bitfld.long 0x00 20. " AUDIOEN ,Audio interface enable" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " BACKPREN ,AShell back pressure enable" "Disabled,Enabled" bitfld.long 0x00 17. " MIIEN ,MII enable" "Disabled,Enabled" textline " " bitfld.long 0x00 16. " ETHERNETMODEEN ,Ethernet mode" "Disabled,Enabled" bitfld.long 0x00 13.--14. " AUDIOESTIMLEVEL ,Estimation interval" "16,32,48,64" textline " " bitfld.long 0x00 10.--12. " ESTIMATION_INTERVAL ,Step size for cycle time change" "250,166,125,83,62,42,31,21" bitfld.long 0x00 1. " CH1PIXEN ,Enable pixel channel 1 in APIX2 core" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " CH0PIXEN ,Enable pixel channel 0 in APIX2 core" "Disabled,Enabled" if (((per.l(ad:0x3A000000+0x11C))&0x300)==0x100) group.long 0x12C++0x03 line.long 0x00 "APIX2_CFG_0, Config for Inova bytes 13_12_11_10 for APIX2 mode MII clock settings" bitfld.long 0x00 31. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24 bit,21 bit" bitfld.long 0x00 29.--30. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "10Bit per Pixel,12Bit per Pixel,18Bit per Pixel,24Bit per Pixel" textline " " bitfld.long 0x00 28. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24 bits,21 bits" bitfld.long 0x00 26.--27. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "10Bit per Pixel,12Bit per Pixel,18Bit per Pixel,24Bit per Pixel" textline " " bitfld.long 0x00 25. " SWAPPIXPATH ,Swap pixel paths TX pixel stream video interface" "Interface 1,Interface 0" bitfld.long 0x00 24. " CLONEPIXPATH ,Clone pixel path TX pixel stream video interface" "Interface 0,Interface 1" textline " " bitfld.long 0x00 23. " ASHELL2_BROADCASTEN ,Broadcast mode of AShell2_0" "Disabled,Enabled" bitfld.long 0x00 22. " ASHELL2_LINKERRORTOL ,Link error tolerance of AShell2_0" "Starts,Repeats" textline " " bitfld.long 0x00 18.--21. " ASHELL2_CRCTOCNT ,CRC timeout counter of AShell2_0" "Disabled,4,6,10,8,16,24,40,32,62,96,160,256,512,768,1280" bitfld.long 0x00 17. " ASHELL2_ARQ_DIS ,Disable ARQ of AShell2_0" "ARQ enable,ARQ disable" textline " " bitfld.long 0x00 16. " ASHELL2_EN ,AShell2_0 enable" "AShell2_0 disable,AShell2_0 enable" bitfld.long 0x00 13.--14. " ASH2UPDIV ,AShell2 upstream bandwidth divider" "/1,/2,/4,/8" textline " " bitfld.long 0x00 8.--12. " DOWNDATABW ,Totally available downstream bandwidth for AShell data audio and GPIO" ",56MBit/s,42MBit/s,,29MBit/s,,,,15MBit/s,,,,,,,,1.3MBit/s,..." bitfld.long 0x00 5. " MIICLKSEL ,Selects one of two internally generated MII clocks" "Clock 0,Clock 1" textline " " bitfld.long 0x00 0.--4. " MIICLK0FREQ ,MII clock frequency(FORMULA187.5 / (2*N) )" "Off,93.75,46.875,31.25,23.4375,18.75,15.625,13.3929,11.7188,10.4167,9.375,8.522,7.8125,7.2115,6.6964,6.25,5.8593,5.5147,5.2083,4.9342,4.6875,4.4642,4.2613,4.0760,3.9062,3.7500,3.6057,3.4722,3.3482,3.2327,3.1250,187.5 / 3" elif (((per.l(ad:0x3A000000+0x11C))&0x300)==0x200) group.long 0x12C++0x03 line.long 0x00 "APIX2_CFG_0, Config for Inova bytes 13_12_11_10 for APIX2 mode MII clock settings" bitfld.long 0x00 31. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24 bit,21 bit" bitfld.long 0x00 29.--30. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "10Bit per Pixel,12Bit per Pixel,18Bit per Pixel,24Bit per Pixel" textline " " bitfld.long 0x00 28. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24 bits,21 bits" bitfld.long 0x00 26.--27. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "10Bit per Pixel,12Bit per Pixel,18Bit per Pixel,24Bit per Pixel" textline " " bitfld.long 0x00 25. " SWAPPIXPATH ,Swap pixel paths TX pixel stream video interface" "Interface 1,Interface 0" bitfld.long 0x00 24. " CLONEPIXPATH ,Clone pixel path TX pixel stream video interface" "Interface 0,Interface 1" textline " " bitfld.long 0x00 23. " ASHELL2_BROADCASTEN ,Broadcast mode of AShell2_0" "Disabled,Enabled" bitfld.long 0x00 22. " ASHELL2_LINKERRORTOL ,Link error tolerance of AShell2_0" "Starts,Repeats" textline " " bitfld.long 0x00 18.--21. " ASHELL2_CRCTOCNT ,CRC timeout counter of AShell2_0" "Disabled,4,6,10,8,16,24,40,32,62,96,160,256,512,768,1280" bitfld.long 0x00 17. " ASHELL2_ARQ_DIS ,Disable ARQ of AShell2_0" "ARQ enable,ARQ disable" textline " " bitfld.long 0x00 16. " ASHELL2_EN ,AShell2_0 enable" "AShell2_0 disable,AShell2_0 enable" bitfld.long 0x00 13.--14. " ASH2UPDIV ,AShell2 upstream bandwidth divider" "/1,/2,/4,/8" textline " " bitfld.long 0x00 8.--12. " DOWNDATABW ,Totally available downstream bandwidth for AShell data audio and GPIO" ",113MBit/s,85MBit/s,,58MBit/s,,,,30MBit/s,,,,,,,,2.6MBit/s,..." bitfld.long 0x00 5. " MIICLKSEL ,Selects one of two internally generated MII clocks" "Clock 0,Clock 1" textline " " bitfld.long 0x00 0.--4. " MIICLK0FREQ ,MII clock frequency(FORMULA187.5 / (2*N) )" "Off,93.75,46.875,31.25,23.4375,18.75,15.625,13.3929,11.7188,10.4167,9.375,8.522,7.8125,7.2115,6.6964,6.25,5.8593,5.5147,5.2083,4.9342,4.6875,4.4642,4.2613,4.0760,3.9062,3.7500,3.6057,3.4722,3.3482,3.2327,3.1250,187.5 / 3" elif (((per.l(ad:0x3A000000+0x11C))&0x300)==0x300) group.long 0x12C++0x03 line.long 0x00 "APIX2_CFG_0, Config for Inova bytes 13_12_11_10 for APIX2 mode MII clock settings" bitfld.long 0x00 31. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24 bit,21 bit" bitfld.long 0x00 29.--30. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "10Bit per Pixel,12Bit per Pixel,18Bit per Pixel,24Bit per Pixel" textline " " bitfld.long 0x00 28. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24 bits,21 bits" bitfld.long 0x00 26.--27. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "10Bit per Pixel,12Bit per Pixel,18Bit per Pixel,24Bit per Pixel" textline " " bitfld.long 0x00 25. " SWAPPIXPATH ,Swap pixel paths TX pixel stream video interface" "Interface 1,Interface 0" bitfld.long 0x00 24. " CLONEPIXPATH ,Clone pixel path TX pixel stream video interface" "Interface 0,Interface 1" textline " " bitfld.long 0x00 23. " ASHELL2_BROADCASTEN ,Broadcast mode of AShell2_0" "Disabled,Enabled" bitfld.long 0x00 22. " ASHELL2_LINKERRORTOL ,Link error tolerance of AShell2_0" "Starts,Repeats" textline " " bitfld.long 0x00 18.--21. " ASHELL2_CRCTOCNT ,CRC timeout counter of AShell2_0" "Disabled,4,6,10,8,16,24,40,32,62,96,160,256,512,768,1280" bitfld.long 0x00 17. " ASHELL2_ARQ_DIS ,Disable ARQ of AShell2_0" "ARQ enable,ARQ disable" textline " " bitfld.long 0x00 16. " ASHELL2_EN ,AShell2_0 enable" "AShell2_0 disable,AShell2_0 enable" bitfld.long 0x00 13.--14. " ASH2UPDIV ,AShell2 upstream bandwidth divider" "/1,/2,/4,/8" textline " " bitfld.long 0x00 8.--12. " DOWNDATABW ,Totally available downstream bandwidth for AShell data audio and GPIO" ",340MBit/s,257MBit/s,,174MBit/s,,,,91MBit/s,,,,,,,,8.7MBit/s,..." bitfld.long 0x00 5. " MIICLKSEL ,Selects one of two internally generated MII clocks" "Clock 0,Clock 1" textline " " bitfld.long 0x00 0.--4. " MIICLK0FREQ ,MII clock frequency(FORMULA187.5 / (2*N) )" "Off,93.75,46.875,31.25,23.4375,18.75,15.625,13.3929,11.7188,10.4167,9.375,8.522,7.8125,7.2115,6.6964,6.25,5.8593,5.5147,5.2083,4.9342,4.6875,4.4642,4.2613,4.0760,3.9062,3.7500,3.6057,3.4722,3.3482,3.2327,3.1250,187.5 / 3" else group.long 0x12C++0x03 line.long 0x00 "APIX2_CFG_0, Config for Inova bytes 13_12_11_10 for APIX2 mode MII clock settings" bitfld.long 0x00 31. " CH1USE21 ,Use 21 of 24 Bit at pixel channel 1" "24 bit,21 bit" bitfld.long 0x00 29.--30. " CH1PIXWIDTH ,Pixel data width at pixel channel 1" "10Bit per Pixel,12Bit per Pixel,18Bit per Pixel,24Bit per Pixel" textline " " bitfld.long 0x00 28. " CH0USE21 ,Use 21 of 24 Bit at pixel channel 0" "24 bits,21 bits" bitfld.long 0x00 26.--27. " CH0PIXWIDTH ,Pixel data width at pixel channel 0" "10Bit per Pixel,12Bit per Pixel,18Bit per Pixel,24Bit per Pixel" textline " " bitfld.long 0x00 25. " SWAPPIXPATH ,Swap pixel paths TX pixel stream video interface" "Interface 1,Interface 0" bitfld.long 0x00 24. " CLONEPIXPATH ,Clone pixel path TX pixel stream video interface" "Interface 0,Interface 1" textline " " bitfld.long 0x00 23. " ASHELL2_BROADCASTEN ,Broadcast mode of AShell2_0" "Disabled,Enabled" bitfld.long 0x00 22. " ASHELL2_LINKERRORTOL ,Link error tolerance of AShell2_0" "Starts,Repeats" textline " " bitfld.long 0x00 18.--21. " ASHELL2_CRCTOCNT ,CRC timeout counter of AShell2_0" "Disabled,4,6,10,8,16,24,40,32,62,96,160,256,512,768,1280" bitfld.long 0x00 17. " ASHELL2_ARQ_DIS ,Disable ARQ of AShell2_0" "ARQ enable,ARQ disable" textline " " bitfld.long 0x00 16. " ASHELL2_EN ,AShell2_0 enable" "AShell2_0 disable,AShell2_0 enable" bitfld.long 0x00 13.--14. " ASH2UPDIV ,AShell2 upstream bandwidth divider" "/1,/2,/4,/8" textline " " bitfld.long 0x00 5. " MIICLKSEL ,Selects one of two internally generated MII clocks" "Clock 0,Clock 1" bitfld.long 0x00 0.--4. " MIICLK0FREQ ,MII clock frequency(FORMULA187.5 / (2*N) )" "Off,93.75,46.875,31.25,23.4375,18.75,15.625,13.3929,11.7188,10.4167,9.375,8.522,7.8125,7.2115,6.6964,6.25,5.8593,5.5147,5.2083,4.9342,4.6875,4.4642,4.2613,4.0760,3.9062,3.7500,3.6057,3.4722,3.3482,3.2327,3.1250,187.5 / 3" endif group.long 0x130++0x13 line.long 0x00 "APIX2_CFG_1,Config for Inova bytes 15_14 for APIX2 mode" bitfld.long 0x00 14. " GPIOUPBW ,GPIO upstream bandwidth mode" "Low,High" bitfld.long 0x00 13. " GPIO0UPEN ,GPIO0 upstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " GPIO1UPEN ,GPIO1 upstream channel enable" "Disabled,Enabled" bitfld.long 0x00 11. " GPIO0DWNEN ,GPIO0 downstream channel enable" "Disabled,Enabled" textline " " bitfld.long 0x00 10. " GPIO1DWNEN ,GPIO1 downstream channel enable" "Disabled,Enabled" bitfld.long 0x00 9. " GPIODWNBW ,GPIO downstream bandwidth mode" "Low,High" textline " " bitfld.long 0x00 8. " GPIODWNHALFBW ,Halve GPIO down bandwidth" "Disabled,Enabled" bitfld.long 0x00 7. " DWNWDFAEN ,Watchdog downstream frame alignment" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " BULKDATAEN ,Bulk data mode" "Disabled,Enabled" bitfld.long 0x00 2. " DWNLENIENTDIS ,Downstream lenient mode disable" "No,Yes" textline " " bitfld.long 0x00 1. " PIXMAJCHECK ,Majority check of parameters in pixel path" "Two,Three" line.long 0x04 "APIX1_CFG_0,Config for Inova bytes 19_18_17_16 for APIX1 mode" bitfld.long 0x04 28.--31. " WINDOW_SIZE ,AShell window size Window size of the retransmission protocol" ",1,2,3,4,5,6,7,8,9,10,11,12,,," bitfld.long 0x04 27. " ARQ_DISABLE ,Retransmission disable" "No,Yes" textline " " bitfld.long 0x04 26. " SUPPRESS_IDLE ,Suppress idle transmission to reduce data traffic" "Disabled,Enabled" bitfld.long 0x04 23. " SBDOWN_VALIDATION ,Validate sbdown_data automatic or with transmitted valid" "Disabled,Valid" textline " " bitfld.long 0x04 21. " ESHELL ,Connect internalAPIX1 PHY to external sideband data through APIX1 GPIO interface" "Enabled,Disabled" bitfld.long 0x04 20. " SPI_OVER_SB ,Selects between two different sideband transmission modes" "Full data,SPI" textline " " bitfld.long 0x04 16.--19. " CRC_TIME_OUT_VALUE ,CRC timeout value" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x04 12.--15. " SBUP_DATA_CYCLETIME3TO0 ,Configures cycle time of sbup clock" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x04 11. " SBUP_DWIDTH ,Enable sbup data ports" "1 bit data,2 bit data" bitfld.long 0x04 9.--10. " SBUP_DACLK ,AShell: generate sbup clock and transmit as sbup_data[1]" "Disabled,Enabled,Enabled,Disabled" textline " " bitfld.long 0x04 8. " SBDOWN_DWIDTH ,Enable sbdown data ports" "1 bit data,2 bit data" hexmask.long.byte 0x04 0.--6. 1. " SBUP_DATA_CYCLETIME10TO4 ,Configures cycle time of sbup clock" line.long 0x08 "APIX1_CFG_1, Config for Inova bytes 1D_1C_1B_1A for APIX1 mode" bitfld.long 0x08 14.--15. " PIXEL_DATA_WIDTH ,Pixel data width" "10Bit per Pixel,12Bit per Pixel,18Bit per Pixel,24Bit per Pixel" bitfld.long 0x08 12.--13. " PX_CTRL_PIGGYBACK ,APIX PHY (Soft IP): transmission of pixel controls" "Never,Unused,Pixel only,With every pixel" textline " " bitfld.long 0x08 7. " ASHELL1_EN ,APIX1 Ashell1 enable" "Disabled,Enabled" bitfld.long 0x08 6. " SBDOWN_CLK_EN ,APIX1 sideband downstream clock enable" "Disabled,Enabled" textline " " bitfld.long 0x08 3. " APIX1DWNLENIENTDIS ,APIX1 mode downstream lenient mode disable" "Mode enabled,Mode Disabled" bitfld.long 0x08 1. " DDOWN_ENABLE ,APIX PHY (Soft IP) / AShell: configure downstream data path" "Disabled,Enablde" textline " " bitfld.long 0x08 0. " EXT_SB_DATA_DIS ,Sideband data are 2-stage registered internal have to be used with external sideband data" "External,No external" line.long 0x0C "APIX1_GPO,GPIO DATA for APIX1 communication" bitfld.long 0x0C 0.--1. " APIX1_GPO ,2 bit GPIO output data" "0,1,2,3" line.long 0x10 "APIX1_GPI_INTCFG,APIX1_GPI_INTCFG" bitfld.long 0x10 1. " APIX1_GPI_INTCFG[1] ,APIX1_GPI_INTCFG" "Rising edge,Falling edge" bitfld.long 0x10 0. " APIX1_GPI_INTCFG[0] ,APIX1_GPI_INTCFG" "Rising edge,Falling edge" rgroup.long 0x144++0x03 line.long 0x00 "APIX1_GPI,GPIO DATA IF for APIX1 communication" bitfld.long 0x00 0.--1. " APIX1_GP ,2 bit GPIO input data" "0,1,2,3" group.long 0x148++0x13 line.long 0x00 "APIX2_GPO,GPIO DATA IF for APIX2 communication" bitfld.long 0x00 0.--1. " APIX2_GPO ,2 bit GPIO output data" "0,1,2,3" line.long 0x04 "APIX2_GPI_INTCFG,APIX2_GPI_INTCFG" bitfld.long 0x04 1. " APIX2_GPI_INTCFG[1] ,APIX1_GPI_INTCFG" "Rising edge,Falling edge" bitfld.long 0x04 0. " APIX2_GPI_INTCFG[0] ,APIX1_GPI_INTCFG" "Rising edge,Falling edge" line.long 0x08 "APIX2_GPI,GPIO DATA IF for APIX2 communication" bitfld.long 0x08 0.--1. " APIX2_GPI ,2 bit GPIO input data corresponds to GPIO pins of INAP1 device" "0,1,2,3" line.long 0x0C "TEST_CONFIG,Configuration for INOVA IP BIST configuration" bitfld.long 0x0C 11.--12. " PSRTEST_8B10B ,PsrTest_8B10B" "Run length 8,Run length 10,Run length 12,Run length 16" bitfld.long 0x0C 10. " PSRTEST_MODE ,PSR test pattern generation" "Disabled,Enabled" line.long 0x10 "TEST_STS_DATA,Inova Bist Status Data input from IP" rbitfld.long 0x10 17. " BISTSYNC ,Inova BIST pseudo random test Sync" "0,1" hexmask.long.word 0x10 0.--15. 1. " BISTERRCNT ,Inova BIST pseudo random test - error counter" rgroup.long 0x174++0x03 line.long 0x00 "DBG_STS_DATA_4,FIR and AGC coefficient status" hexmask.long.byte 0x00 24.--30. 1. " DBG_RX_FIR_COEFF0 ,Currently set FIR coefficient 0 including sign" hexmask.long.byte 0x00 16.--22. 1. " DBG_RX_AGC_COEFF ,Currently set AGC coefficient" group.long 0x178++0x03 line.long 0x00 "DBG_STS_DATA_5,FIR coefficient status" hexmask.long.byte 0x00 8.--14. 1. " DBG_RX_FIR_COEFF2 ,Currently set FIR coefficient 2 including sign" hexmask.long.byte 0x00 0.--6. 1. " DBG_RX_FIR_COEFF1 ,Currently set FIR coefficient 1 including sign" group.long 0x200++0x07 line.long 0x00 "APIX_CTRL_0,General control register" eventfld.long 0x00 4. " AUDIOCLK_RESTART ,Audio clock synthesis controller restart" "No restart,Restart" eventfld.long 0x00 2. " ASHELL2_0_TADIFFCNT_CLEAR ,Clear field AShell2_0_TADiffCnt by writinga 1" "-,Clear" textline " " eventfld.long 0x00 1. " ASHELL1_REALIGN ,Apix1 AShell realign" "Not Realign,Realign" eventfld.long 0x00 1. " ASHELL2_REALIGN ,Apix2 AShell realign" "Not Realign,Realign" line.long 0x04 "APIX_CTRL_1,Reset for counter values " eventfld.long 0x04 7. " BISTERRCNTCLEAR ,Clear Inova BIST pseudo random test error counter" "-,Clear" eventfld.long 0x04 5. " ASHELL2_0_CRCERRCNTCLEAR ,Clear Ashell2_0_CRCErrCnt" "-,Clear" textline " " eventfld.long 0x04 4. " ASHELL1_CRCERRCNTCLEAR ,Clear Ashell2_1_CRCErrCnt" "-,Clear" eventfld.long 0x04 3. " APIX1DOWNFALIGNERRCNTCLEAR ,Clear Apix1downFAlignErrCnt" "-,Clear" textline " " eventfld.long 0x04 1. " APIX2DOWNFALIGNERRCNTCLEAR ,Clear Apix2downFAlignErrCnt" "-,Clear" rgroup.long 0x20C++0x0F line.long 0x00 "APIX2_STATUS_0,Status register for Inova bytes 04 03" bitfld.long 0x00 14. " APIX2DOWNFALIGN ,Apix2 downstream frame aligned" "No,Yes" bitfld.long 0x00 8.--13. " APIX2DOWNFALIGNERRCNT ,Downstream frame aligned error counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" line.long 0x04 "APIX2_STATUS_1,Status register for Inova bytes 07_06_05 general status information of AShell2_0" hexmask.long.byte 0x04 16.--23. 1. " ASHELL2_0_CRCERRCNT ,CRC error counter of AShell2_0" hexmask.long.byte 0x04 8.--15. 1. " ASHELL2_0_TADIFFCNT ,Transaction counter difference of AShell2_0" textline " " bitfld.long 0x04 1. " ASHELL2_0_OPERATIONAL ,AShell operational" "No,Yes" line.long 0x08 "APIX1_STATUS_0,Status from Inova Status bytes 08_09_0A" bitfld.long 0x08 22. " APIX1DOWNFRAMEALIGNED ,Apix1 downstream frame aligned" "No,Yes" bitfld.long 0x08 16.--21. " APIX1DOWNFALIGNERRCNT ,Apix1 downstream frame aligned error counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " bitfld.long 0x08 10.--15. " ASHELL1_CRCERRCNT ,Apix1 AShell CRC error counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" bitfld.long 0x08 1. " ASHELL1_OPERATIONAL ,Apix1 AShell operational" "No,Yes" line.long 0x0C "APIX12_STATUS_1, Status register for Inova bytes 0C 0B pixel fifo status" bitfld.long 0x0C 14. " APIX1PIXALIGNED ,Apix1 mode pixel stream aligned" "No,Yes" bitfld.long 0x0C 7. " CH1PIXFIFOEMPTY ,Pixel channel 1 FIFO empty" "Not empty,Empty" textline " " bitfld.long 0x0C 6. " CH1PIXFIFOFULL ,Pixel channel 1 FIFO full" "Not full,Full" bitfld.long 0x0C 5. " CH0PIXFIFOEMPTY ,Pixel channel 0 FIFO empty" "Not empty,Empty" textline " " bitfld.long 0x0C 4. " CH0PIXFIFOFULL ,Pixel channel 0 FIFO full" "Not full,Full" width 13. tree "Interrupt registers" rgroup.long 0x300++0x07 line.long 0x00 "INTSTATUS0,Interrupt Status Register 0" bitfld.long 0x00 31. " APIX2_GPI_1 ,Edge detected at APIX2 GPI_1 port" "Inactive,Active" bitfld.long 0x00 30. " APIX2_GPI_0 ,Edge detected at APIX2 GPI_0 port" "Inactive,Active" textline " " bitfld.long 0x00 29. " APIX1_GPI_1 ,Edge detected at APIX1 GPI_1 port" "Inactive,Active" bitfld.long 0x00 28. " APIX1_GPI_0 ,Edge detected at APIX1 GPI_0 port" "Inactive,Active" textline " " bitfld.long 0x00 26. " FRAME_ALIGNMENT_TIMEOUT_DETECT ,Signalizes that the device was not frame aligned when the watchdog of frame alignment was expired" "Inactive,Active" textline " " bitfld.long 0x00 25. " REMOTE_INBOUND_I2C_JOB_CANCEL ,APIX2 Ashell2Remote command cancel I2C job received" "Inactive,Active" bitfld.long 0x00 24. " REMOTE_INBOUND_ASHELL2_CLEAR_TICKET_COUNTER ,APIX2 Ashell2 Remote command clear Ashell2 ticket counter received" "Inactive,Active" textline " " bitfld.long 0x00 23. " REMOTE_INBOUND_ASHELL2_REALIGN ,APIX2 Ashell2 Remote command realign Ashell2 received" "Inactive,Active" bitfld.long 0x00 22. " REMOTE_INBOUND_SOFT_RESET ,APIX2 Ashell2 Remote command soft reset received" "Inactive,Active" textline " " bitfld.long 0x00 21. " CH0PIXFATAL ,APIX2 PIX Pixel channel 0 fatal error on pixel control transmission" "Inactive,Active" bitfld.long 0x00 20. " CH1PIXFATAL ,APIX2 PIX Pixel channel 1 fatal error on pixel control transmission" "Inactive,Active" textline " " bitfld.long 0x00 19. " APIX1_PIXALIGNEDLOSS ,APIX1 PIX Pixel stream looses alignment" "Inactive,Active" bitfld.long 0x00 18. " APIX1_PIXALIGNED ,APIX1 PIX Pixel stream becomes aligned" "Inactive,Active" textline " " bitfld.long 0x00 17. " INT_CH0PIXFIFOFULL ,APIX2 PIX, Channel 0 Pixel FIFO is full" "Inactive,Active" bitfld.long 0x00 16. " INT_CH0PIXFIFOEMPTY ,APIX2 PIX Channel 0 Pixel FIFO is empty" "Inactive,Active" textline " " bitfld.long 0x00 15. " INT_CH1PIXFIFOFULL ,APIX2 PIX Channel 1 Pixel FIFO is full" "Inactive,Active" bitfld.long 0x00 14. " INT_CH1PIXFIFOEMPTY ,APIX2 PIX Channel 1 Pixel FIFO is empty" "Inactive,Active" textline " " bitfld.long 0x00 13. " APIX1_DOWNREADYLOSS ,APIX1 PHY Loss of APIX1 downstream PHY frame alignment" "Inactive,Active" bitfld.long 0x00 12. " ASHELL1_FATAL ,APIX1 Ashell1 Fatal Error" "Inactive,Active" textline " " bitfld.long 0x00 11. " ASHELL1_CRCERROR ,APIX1 Ashell1 CRC Error incoming transaction is defective" "Inactive,Active" bitfld.long 0x00 10. " ASHELL1_UNCONNECTED ,APIX1 Ashell1 looses operational state" "Inactive,Active" textline " " bitfld.long 0x00 9. " ASHELL1_CONNECTED ,APIX1 Ashell1 enters operational state" "Inactive,Active" bitfld.long 0x00 8. " ASHELL1_CRCTIMEOUT ,APIX1 Ashell1 CRC Timeout" "Inactive,Active" textline " " bitfld.long 0x00 7. " ASHELL1_PROTERR ,APIX1 Ashell1 Protocol Error" "Inactive,Active" bitfld.long 0x00 6. " ASHELL1_REMRESTARTED ,APIX1 Ashell1 remote AShell was restarted" "Inactive,Active" textline " " bitfld.long 0x00 5. " ASHELL2_UNCONNECTED ,APIX2 Ashell2 looses operational state" "Inactive,Active" bitfld.long 0x00 4. " ASHELL2_CONNECTED ,APIX2 Ashell2 enters operational state" "Inactive,Active" textline " " bitfld.long 0x00 3. " ASHELL2_TALOSS ,APIX2 Ashell2 Transaction loss" "Inactive,Active" bitfld.long 0x00 2. " ASHELL2_FATAL ,APIX2 Ashell2 Fatal Error" "Inactive,Active" textline " " bitfld.long 0x00 1. " ASHELL2_CRCERROR ,APIX2 Ashell2 CRC Error incoming transaction is defective" "Inactive,Active" bitfld.long 0x00 0. " APIX2DOWNFRAMEALIGNEDLOSS ,APIX2 PHY Loss of APIX2 downstream PHY frame alignment" "Inactive,Active" line.long 0x04 "INTSTATUS1,Interrupt Status Register 1" bitfld.long 0x04 30. " PLL_GOOD_LOSS ,APIX PHY Detected falling edge at pll_good from PHY" "Inactive,Active" bitfld.long 0x04 29. " PLL_GOOD ,APIX PHY Detected rising edge at pll_good from PHY" "Inactive,Active" textline " " bitfld.long 0x04 28. " STATUS_TIMEOUT ,APIX2RX_link Abort of read access to status register happened" "Inactive,Active" bitfld.long 0x04 27. " REFRAMER_UNDERRUN ,Reframer FIFO underrun error" "Inactive,Active" textline " " bitfld.long 0x04 26. " REFRAMER_OVERFLOW ,Reframer FIFO overflow error" "Inactive,Active" bitfld.long 0x04 25. " REFRAMER_INTTX2 ,Reframer has lost synchronization to the received video timing" "Inactive,Active" textline " " bitfld.long 0x04 24. " REFRAMER_INTTX1 ,Reframer tx1 programmable interrupt" "Inactive,Active" bitfld.long 0x04 23. " REFRAMER_INTTX0 ,Reframer tx0 programmable interrupt" "Inactive,Active" textline " " bitfld.long 0x04 22. " REFRAMER_INTRX ,Reframer rx vsync interrupt" "Inactive,Active" bitfld.long 0x04 21. " REMOTE_SERVICE_INBOUND_ERROR ,Remote_service_inbound_error" "Inactive,Active" textline " " bitfld.long 0x04 20. " REMOTE_SERVICE_INBOUND_VALID ,APIX2 remote IF Received valid inbound data from remote service IF" "Inactive,Active" bitfld.long 0x04 19. " REMOTE_CONTROLLER_INBOUND_ERROR ,APIX2 remote IF Data loss at inbound remote control data register" "Inactive,Active" textline " " bitfld.long 0x04 18. " REMOTE_CONTROLLER_INBOUND_VALID ,APIX2 remote IF Received valid inbound data from remote control IF" "Inactive,Active" bitfld.long 0x04 17. " I2C_INBOUND_READ_RESPONSE_ERROR ,APIX2 remote i2c Data loss at i2c inbound read response register" "Inactive,Active" textline " " bitfld.long 0x04 16. " I2C_INBOUND_READ_RESPONSE_VALID ,APIX2 remote i2c Received valid inbound I2C read response" "Inactive,Active" bitfld.long 0x04 15. " I2C_INBOUND_STATUS_ERROR ,APIX2 remote i2c Data loss at inbound i2c status register" "Inactive,Active" textline " " bitfld.long 0x04 14. " I2C_INBOUND_STATUS_VALID ,APIX2 remote i2c Received valid inbound i2c status" "Inactive,Active" bitfld.long 0x04 13. " I2C_INBOUND_JOB_SPEC_ERROR ,APIX2 remote i2c Data loss at i2c job specification register" "Inactive,Active" textline " " bitfld.long 0x04 12. " I2C_INBOUND_JOB_SPEC_VALID ,APIX2 remote i2c Received valid inbound i2c job specification" "Inactive,Active" bitfld.long 0x04 11. " WDG_TIMEOUT ,Message buffer Wrbuf Watchdog timeout" "Inactive,Active" textline " " bitfld.long 0x04 10. " WRBUF_EMPTY_INT ,Message buffer Write buffer #1 becomes empty" "Inactive,Active" bitfld.long 0x04 9. " WRBUF_FULL_INT ,Message buffer Write buffer #1 becomes full" "Inactive,Active" textline " " bitfld.long 0x04 8. " R1BUF_NOT_EMPTY ,Message buffer Read buffer #1 becomes not empty" "Inactive,Active" bitfld.long 0x04 7. " R1BUF_FULL_INT ,Message buffer Read buffer #1 becomes full" "Inactive,Active" textline " " bitfld.long 0x04 6. " R0BUF_NOT_EMPTY ,Message buffer Read buffer #0 becomes not empty" "Inactive,Active" bitfld.long 0x04 5. " R0BUF_FULL_INT ,Message buffer Read buffer #0 becomes full" "Inactive,Active" textline " " bitfld.long 0x04 4. " WRBUF_OVERFLOW ,Message buffer Write buffer overflow" "Inactive,Active" bitfld.long 0x04 3. " R1BUF_UNDERRUN ,Message buffer Read buffer #1 underrun" "Inactive,Active" textline " " bitfld.long 0x04 2. " R1BUF_OVERFLOW ,Message buffer Read buffer #1 overflow" "Inactive,Active" bitfld.long 0x04 1. " R0BUF_UNDERRUN ,Message buffer Read buffer #0 underrun" "Inactive,Active" textline " " bitfld.long 0x04 0. " R0BUF_OVERFLOW ,Message buffer Read buffer #0 overflow" "Inactive,Active" group.long 0x308++0x1F line.long 0x00 "INT0ENABLE0,Interrupt Enable Register 0 for interrupts bits" bitfld.long 0x00 31. " INT0ENABLE0_[31] ,Interrupt 0 Enable bit 31" "Disabled,Enabled" bitfld.long 0x00 30. " [30] ,Interrupt 0 Enable bit 30" "Disabled,Enabled" bitfld.long 0x00 29. " [29] ,Interrupt 0 Enable bit 29" "Disabled,Enabled" bitfld.long 0x00 28. " [28] ,Interrupt 0 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x00 27. " [27] ,Interrupt 0 Enable bit 27" "Disabled,Enabled" bitfld.long 0x00 26. " [26] ,Interrupt 0 Enable bit 26" "Disabled,Enabled" bitfld.long 0x00 25. " [25] ,Interrupt 0 Enable bit 25" "Disabled,Enabled" bitfld.long 0x00 24. " [24] ,Interrupt 0 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x00 23. " [23] ,Interrupt 0 Enable bit 23" "Disabled,Enabled" bitfld.long 0x00 22. " [22] ,Interrupt 0 Enable bit 22" "Disabled,Enabled" bitfld.long 0x00 21. " [21] ,Interrupt 0 Enable bit 21" "Disabled,Enabled" bitfld.long 0x00 20. " [20] ,Interrupt 0 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " [19] ,Interrupt 0 Enable bit 19" "Disabled,Enabled" bitfld.long 0x00 18. " [18] ,Interrupt 0 Enable bit 18" "Disabled,Enabled" bitfld.long 0x00 17. " [17] ,Interrupt 0 Enable bit 17" "Disabled,Enabled" bitfld.long 0x00 16. " [16] ,Interrupt 0 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x00 15. " [15] ,Interrupt 0 Enable bit 15" "Disabled,Enabled" bitfld.long 0x00 14. " [14] ,Interrupt 0 Enable bit 14" "Disabled,Enabled" bitfld.long 0x00 13. " [13] ,Interrupt 0 Enable bit 13" "Disabled,Enabled" bitfld.long 0x00 12. " [12] ,Interrupt 0 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x00 11. " [11] ,Interrupt 0 Enable bit 11" "Disabled,Enabled" bitfld.long 0x00 10. " [10] ,Interrupt 0 Enable bit 10" "Disabled,Enabled" bitfld.long 0x00 9. " [9] ,Interrupt 0 Enable bit 9" "Disabled,Enabled" bitfld.long 0x00 8. " [8] ,Interrupt 0 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " [7] ,Interrupt 0 Enable bit 7" "Disabled,Enabled" bitfld.long 0x00 6. " [6] ,Interrupt 0 Enable bit 6" "Disabled,Enabled" bitfld.long 0x00 5. " [5] ,Interrupt 0 Enable bit 5" "Disabled,Enabled" bitfld.long 0x00 4. " [4] ,Interrupt 0 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " [3] ,Interrupt 0 Enable bit 3" "Disabled,Enabled" bitfld.long 0x00 2. " [2] ,Interrupt 0 Enable bit 2" "Disabled,Enabled" bitfld.long 0x00 1. " [1] ,Interrupt 0 Enable bit 1" "Disabled,Enabled" bitfld.long 0x00 0. " [0] ,Interrupt 0 Enable bit 0" "Disabled,Enabled" line.long 0x04 "INT0ENABLE1,Interrupt Enable Register 1 for interrupts bits" bitfld.long 0x04 30. " INT0ENABLE1_[30] ,Interrupt 0 Enable bit 30" "Disabled,Enabled" bitfld.long 0x04 29. " [29] ,Interrupt 0 Enable bit 29" "Disabled,Enabled" bitfld.long 0x04 28. " [28] ,Interrupt 0 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x04 27. " [27] ,Interrupt 0 Enable bit 27" "Disabled,Enabled" bitfld.long 0x04 26. " [26] ,Interrupt 0 Enable bit 26" "Disabled,Enabled" bitfld.long 0x04 25. " [25] ,Interrupt 0 Enable bit 25" "Disabled,Enabled" bitfld.long 0x04 24. " [24] ,Interrupt 0 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x04 23. " [23] ,Interrupt 0 Enable bit 23" "Disabled,Enabled" bitfld.long 0x04 22. " [22] ,Interrupt 0 Enable bit 22" "Disabled,Enabled" bitfld.long 0x04 21. " [21] ,Interrupt 0 Enable bit 21" "Disabled,Enabled" bitfld.long 0x04 20. " [20] ,Interrupt 0 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x04 19. " [19] ,Interrupt 0 Enable bit 19" "Disabled,Enabled" bitfld.long 0x04 18. " [18] ,Interrupt 0 Enable bit 18" "Disabled,Enabled" bitfld.long 0x04 17. " [17] ,Interrupt 0 Enable bit 17" "Disabled,Enabled" bitfld.long 0x04 16. " [16] ,Interrupt 0 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x04 15. " [15] ,Interrupt 0 Enable bit 15" "Disabled,Enabled" bitfld.long 0x04 14. " [14] ,Interrupt 0 Enable bit 14" "Disabled,Enabled" bitfld.long 0x04 13. " [13] ,Interrupt 0 Enable bit 13" "Disabled,Enabled" bitfld.long 0x04 12. " [12] ,Interrupt 0 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x04 11. " [11] ,Interrupt 0 Enable bit 11" "Disabled,Enabled" bitfld.long 0x04 10. " [10] ,Interrupt 0 Enable bit 10" "Disabled,Enabled" bitfld.long 0x04 9. " [9] ,Interrupt 0 Enable bit 9" "Disabled,Enabled" bitfld.long 0x04 8. " [8] ,Interrupt 0 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x04 7. " [7] ,Interrupt 0 Enable bit 7" "Disabled,Enabled" bitfld.long 0x04 6. " [6] ,Interrupt 0 Enable bit 6" "Disabled,Enabled" bitfld.long 0x04 5. " [5] ,Interrupt 0 Enable bit 5" "Disabled,Enabled" bitfld.long 0x04 4. " [4] ,Interrupt 0 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x04 3. " [3] ,Interrupt 0 Enable bit 3" "Disabled,Enabled" bitfld.long 0x04 2. " [2] ,Interrupt 0 Enable bit 2" "Disabled,Enabled" bitfld.long 0x04 1. " [1] ,Interrupt 0 Enable bit 1" "Disabled,Enabled" bitfld.long 0x04 0. " [0] ,Interrupt 0 Enable bit 0" "Disabled,Enabled" line.long 0x08 "INT1ENABLE0,Interrupt Enable Register 0 for interrupts bits" bitfld.long 0x08 31. " INT1ENABLE0_[31] ,Interrupt 1 Enable bit 31" "Disabled,Enabled" bitfld.long 0x08 30. " [30] ,Interrupt 1 Enable bit 30" "Disabled,Enabled" bitfld.long 0x08 29. " [29] ,Interrupt 1 Enable bit 29" "Disabled,Enabled" bitfld.long 0x08 28. " [28] ,Interrupt 1 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x08 27. " [27] ,Interrupt 1 Enable bit 27" "Disabled,Enabled" bitfld.long 0x08 26. " [26] ,Interrupt 1 Enable bit 26" "Disabled,Enabled" bitfld.long 0x08 25. " [25] ,Interrupt 1 Enable bit 25" "Disabled,Enabled" bitfld.long 0x08 24. " [24] ,Interrupt 1 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x08 23. " [23] ,Interrupt 1 Enable bit 23" "Disabled,Enabled" bitfld.long 0x08 22. " [22] ,Interrupt 1 Enable bit 22" "Disabled,Enabled" bitfld.long 0x08 21. " [21] ,Interrupt 1 Enable bit 21" "Disabled,Enabled" bitfld.long 0x08 20. " [20] ,Interrupt 1 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x08 19. " [19] ,Interrupt 1 Enable bit 19" "Disabled,Enabled" bitfld.long 0x08 18. " [18] ,Interrupt 1 Enable bit 18" "Disabled,Enabled" bitfld.long 0x08 17. " [17] ,Interrupt 1 Enable bit 17" "Disabled,Enabled" bitfld.long 0x08 16. " [16] ,Interrupt 1 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x08 15. " [15] ,Interrupt 1 Enable bit 15" "Disabled,Enabled" bitfld.long 0x08 14. " [14] ,Interrupt 1 Enable bit 14" "Disabled,Enabled" bitfld.long 0x08 13. " [13] ,Interrupt 1 Enable bit 13" "Disabled,Enabled" bitfld.long 0x08 12. " [12] ,Interrupt 1 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x08 11. " [11] ,Interrupt 1 Enable bit 11" "Disabled,Enabled" bitfld.long 0x08 10. " [10] ,Interrupt 1 Enable bit 10" "Disabled,Enabled" bitfld.long 0x08 9. " [9] ,Interrupt 1 Enable bit 9" "Disabled,Enabled" bitfld.long 0x08 8. " [8] ,Interrupt 1 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x08 7. " [7] ,Interrupt 1 Enable bit 7" "Disabled,Enabled" bitfld.long 0x08 6. " [6] ,Interrupt 1 Enable bit 6" "Disabled,Enabled" bitfld.long 0x08 5. " [5] ,Interrupt 1 Enable bit 5" "Disabled,Enabled" bitfld.long 0x08 4. " [4] ,Interrupt 1 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x08 3. " [3] ,Interrupt 1 Enable bit 3" "Disabled,Enabled" bitfld.long 0x08 2. " [2] ,Interrupt 1 Enable bit 2" "Disabled,Enabled" bitfld.long 0x08 1. " [1] ,Interrupt 1 Enable bit 1" "Disabled,Enabled" bitfld.long 0x08 0. " [0] ,Interrupt 1 Enable bit 0" "Disabled,Enabled" line.long 0x0C "INT1ENABLE1,Interrupt Enable Register 1 for interrupts bits" bitfld.long 0x0C 30. " INT1ENABLE1_[30] ,Interrupt 1 Enable bit 30" "Disabled,Enabled" bitfld.long 0x0C 29. " [29] ,Interrupt 1 Enable bit 29" "Disabled,Enabled" bitfld.long 0x0C 28. " [28] ,Interrupt 1 Enable bit 28" "Disabled,Enabled" textline " " bitfld.long 0x0C 27. " [27] ,Interrupt 1 Enable bit 27" "Disabled,Enabled" bitfld.long 0x0C 26. " [26] ,Interrupt 1 Enable bit 26" "Disabled,Enabled" bitfld.long 0x0C 25. " [25] ,Interrupt 1 Enable bit 25" "Disabled,Enabled" bitfld.long 0x0C 24. " [24] ,Interrupt 1 Enable bit 24" "Disabled,Enabled" textline " " bitfld.long 0x0C 23. " [23] ,Interrupt 1 Enable bit 23" "Disabled,Enabled" bitfld.long 0x0C 22. " [22] ,Interrupt 1 Enable bit 22" "Disabled,Enabled" bitfld.long 0x0C 21. " [21] ,Interrupt 1 Enable bit 21" "Disabled,Enabled" bitfld.long 0x0C 20. " [20] ,Interrupt 1 Enable bit 20" "Disabled,Enabled" textline " " bitfld.long 0x0C 19. " [19] ,Interrupt 1 Enable bit 19" "Disabled,Enabled" bitfld.long 0x0C 18. " [18] ,Interrupt 1 Enable bit 18" "Disabled,Enabled" bitfld.long 0x0C 17. " [17] ,Interrupt 1 Enable bit 17" "Disabled,Enabled" bitfld.long 0x0C 16. " [16] ,Interrupt 1 Enable bit 16" "Disabled,Enabled" textline " " bitfld.long 0x0C 15. " [15] ,Interrupt 1 Enable bit 15" "Disabled,Enabled" bitfld.long 0x0C 14. " [14] ,Interrupt 1 Enable bit 14" "Disabled,Enabled" bitfld.long 0x0C 13. " [13] ,Interrupt 1 Enable bit 13" "Disabled,Enabled" bitfld.long 0x0C 12. " [12] ,Interrupt 1 Enable bit 12" "Disabled,Enabled" textline " " bitfld.long 0x0C 11. " [11] ,Interrupt 1 Enable bit 11" "Disabled,Enabled" bitfld.long 0x0C 10. " [10] ,Interrupt 1 Enable bit 10" "Disabled,Enabled" bitfld.long 0x0C 9. " [9] ,Interrupt 1 Enable bit 9" "Disabled,Enabled" bitfld.long 0x0C 8. " [8] ,Interrupt 1 Enable bit 8" "Disabled,Enabled" textline " " bitfld.long 0x0C 7. " [7] ,Interrupt 1 Enable bit 7" "Disabled,Enabled" bitfld.long 0x0C 6. " [6] ,Interrupt 1 Enable bit 6" "Disabled,Enabled" bitfld.long 0x0C 5. " [5] ,Interrupt 1 Enable bit 5" "Disabled,Enabled" bitfld.long 0x0C 4. " [4] ,Interrupt 1 Enable bit 4" "Disabled,Enabled" textline " " bitfld.long 0x0C 3. " [3] ,Interrupt 1 Enable bit 3" "Disabled,Enabled" bitfld.long 0x0C 2. " [2] ,Interrupt 1 Enable bit 2" "Disabled,Enabled" bitfld.long 0x0C 1. " [1] ,Interrupt 1 Enable bit 1" "Disabled,Enabled" bitfld.long 0x0C 0. " [0] ,Interrupt 1 Enable bit 0" "Disabled,Enabled" line.long 0x10 "INTCLEAR0,Interrupt Clear Register 0 for interrupt bits" eventfld.long 0x10 31. " INTCLEAR0_[31] ,Interrupt Clear bit 31" "Not clear,Clear" eventfld.long 0x10 30. " [30] ,Interrupt Clear bit 30" "Not clear,Clear" eventfld.long 0x10 29. " [29] ,Interrupt Clear bit 29" "Not clear,Clear" eventfld.long 0x10 28. " [28] ,Interrupt Clear bit 28" "Not clear,Clear" textline " " eventfld.long 0x10 27. " [27] ,Interrupt Clear bit 27" "Not clear,Clear" eventfld.long 0x10 26. " [26] ,Interrupt Clear bit 26" "Not clear,Clear" eventfld.long 0x10 25. " [25] ,Interrupt Clear bit 25" "Not clear,Clear" eventfld.long 0x10 24. " [24] ,Interrupt Clear bit 24" "Not clear,Clear" textline " " eventfld.long 0x10 23. " [23] ,Interrupt Clear bit 23" "Not clear,Clear" eventfld.long 0x10 22. " [22] ,Interrupt Clear bit 22" "Not clear,Clear" eventfld.long 0x10 21. " [21] ,Interrupt Clear bit 21" "Not clear,Clear" eventfld.long 0x10 20. " [20] ,Interrupt Clear bit 20" "Not clear,Clear" textline " " eventfld.long 0x10 19. " [19] ,Interrupt Clear bit 19" "Not clear,Clear" eventfld.long 0x10 18. " [18] ,Interrupt Clear bit 18" "Not clear,Clear" eventfld.long 0x10 17. " [17] ,Interrupt Clear bit 17" "Not clear,Clear" eventfld.long 0x10 16. " [16] ,Interrupt Clear bit 16" "Not clear,Clear" textline " " eventfld.long 0x10 15. " [15] ,Interrupt Clear bit 15" "Not clear,Clear" eventfld.long 0x10 14. " [14] ,Interrupt Clear bit 14" "Not clear,Clear" eventfld.long 0x10 13. " [13] ,Interrupt Clear bit 13" "Not clear,Clear" eventfld.long 0x10 12. " [12] ,Interrupt Clear bit 12" "Not clear,Clear" textline " " eventfld.long 0x10 11. " [11] ,Interrupt Clear bit 11" "Not clear,Clear" eventfld.long 0x10 10. " [10] ,Interrupt Clear bit 10" "Not clear,Clear" eventfld.long 0x10 9. " [9] ,Interrupt Clear bit 9" "Not clear,Clear" eventfld.long 0x10 8. " [8] ,Interrupt Clear bit 8" "Not clear,Clear" textline " " eventfld.long 0x10 7. " [7] ,Interrupt Clear bit 7" "Not clear,Clear" eventfld.long 0x10 6. " [6] ,Interrupt Clear bit 6" "Not clear,Clear" eventfld.long 0x10 5. " [5] ,Interrupt Clear bit 5" "Not clear,Clear" eventfld.long 0x10 4. " [4] ,Interrupt Clear bit 4" "Not clear,Clear" textline " " eventfld.long 0x10 3. " [3] ,Interrupt Clear bit 3" "Not clear,Clear" eventfld.long 0x10 2. " [2] ,Interrupt Clear bit 2" "Not clear,Clear" eventfld.long 0x10 1. " [1] ,Interrupt Clear bit 1" "Not clear,Clear" eventfld.long 0x10 0. " [0] ,Interrupt Clear bit 0" "Not clear,Clear" line.long 0x14 "INTCLEAR1,Interrupt Clear Register 1 for interrupt bits" eventfld.long 0x14 31. " INTCLEAR1_[31] ,Interrupt Clear bit 31" "Not clear,Clear" eventfld.long 0x14 30. " [30] ,Interrupt Clear bit 30" "Not clear,Clear" eventfld.long 0x14 29. " [29] ,Interrupt Clear bit 29" "Not clear,Clear" eventfld.long 0x14 28. " [28] ,Interrupt Clear bit 28" "Not clear,Clear" textline " " eventfld.long 0x14 27. " [27] ,Interrupt Clear bit 27" "Not clear,Clear" eventfld.long 0x14 26. " [26] ,Interrupt Clear bit 26" "Not clear,Clear" eventfld.long 0x14 25. " [25] ,Interrupt Clear bit 25" "Not clear,Clear" eventfld.long 0x14 24. " [24] ,Interrupt Clear bit 24" "Not clear,Clear" textline " " eventfld.long 0x14 23. " [23] ,Interrupt Clear bit 23" "Not clear,Clear" eventfld.long 0x14 22. " [22] ,Interrupt Clear bit 22" "Not clear,Clear" eventfld.long 0x14 21. " [21] ,Interrupt Clear bit 21" "Not clear,Clear" eventfld.long 0x14 20. " [20] ,Interrupt Clear bit 20" "Not clear,Clear" textline " " eventfld.long 0x14 19. " [19] ,Interrupt Clear bit 19" "Not clear,Clear" eventfld.long 0x14 18. " [18] ,Interrupt Clear bit 18" "Not clear,Clear" eventfld.long 0x14 17. " [17] ,Interrupt Clear bit 17" "Not clear,Clear" eventfld.long 0x14 16. " [16] ,Interrupt Clear bit 16" "Not clear,Clear" textline " " eventfld.long 0x14 15. " [15] ,Interrupt Clear bit 15" "Not clear,Clear" eventfld.long 0x14 14. " [14] ,Interrupt Clear bit 14" "Not clear,Clear" eventfld.long 0x14 13. " [13] ,Interrupt Clear bit 13" "Not clear,Clear" eventfld.long 0x14 12. " [12] ,Interrupt Clear bit 12" "Not clear,Clear" textline " " eventfld.long 0x14 11. " [11] ,Interrupt Clear bit 11" "Not clear,Clear" eventfld.long 0x14 10. " [10] ,Interrupt Clear bit 10" "Not clear,Clear" eventfld.long 0x14 9. " [9] ,Interrupt Clear bit 9" "Not clear,Clear" eventfld.long 0x14 8. " [8] ,Interrupt Clear bit 8" "Not clear,Clear" textline " " eventfld.long 0x14 7. " [7] ,Interrupt Clear bit 7" "Not clear,Clear" eventfld.long 0x14 6. " [6] ,Interrupt Clear bit 6" "Not clear,Clear" eventfld.long 0x14 5. " [5] ,Interrupt Clear bit 5" "Not clear,Clear" eventfld.long 0x14 4. " [4] ,Interrupt Clear bit 4" "Not clear,Clear" textline " " eventfld.long 0x14 3. " [3] ,Interrupt Clear bit 3" "Not clear,Clear" eventfld.long 0x14 2. " [2] ,Interrupt Clear bit 2" "Not clear,Clear" eventfld.long 0x14 1. " [1] ,Interrupt Clear bit 1" "Not clear,Clear" eventfld.long 0x14 0. " [0] ,Interrupt Clear bit 0" "Not clear,Clear" line.long 0x18 "INTPRESET0,Interrupt Preset Register 1 for interrupt bits" eventfld.long 0x18 31. " INTPRESET0_[31] ,Interrupt Preset bit 31" "Not interrupt,Interrupt" eventfld.long 0x18 30. " [30] ,Interrupt Preset bit 30" "Not interrupt,Interrupt" eventfld.long 0x18 29. " [29] ,Interrupt Preset bit 29" "Not interrupt,Interrupt" eventfld.long 0x18 28. " [28] ,Interrupt Preset bit 28" "Not interrupt,Interrupt" textline " " eventfld.long 0x18 27. " [27] ,Interrupt Preset bit 27" "Not interrupt,Interrupt" eventfld.long 0x18 26. " [26] ,Interrupt Preset bit 26" "Not interrupt,Interrupt" eventfld.long 0x18 25. " [25] ,Interrupt Preset bit 25" "Not interrupt,Interrupt" eventfld.long 0x18 24. " [24] ,Interrupt Preset bit 24" "Not interrupt,Interrupt" textline " " eventfld.long 0x18 23. " [23] ,Interrupt Preset bit 23" "Not interrupt,Interrupt" eventfld.long 0x18 22. " [22] ,Interrupt Preset bit 22" "Not interrupt,Interrupt" eventfld.long 0x18 21. " [21] ,Interrupt Preset bit 21" "Not interrupt,Interrupt" eventfld.long 0x18 20. " [20] ,Interrupt Preset bit 20" "Not interrupt,Interrupt" textline " " eventfld.long 0x18 19. " [19] ,Interrupt Preset bit 19" "Not interrupt,Interrupt" eventfld.long 0x18 18. " [18] ,Interrupt Preset bit 18" "Not interrupt,Interrupt" eventfld.long 0x18 17. " [17] ,Interrupt Preset bit 17" "Not interrupt,Interrupt" eventfld.long 0x18 16. " [16] ,Interrupt Preset bit 16" "Not interrupt,Interrupt" textline " " eventfld.long 0x18 15. " [15] ,Interrupt Preset bit 15" "Not interrupt,Interrupt" eventfld.long 0x18 14. " [14] ,Interrupt Preset bit 14" "Not interrupt,Interrupt" eventfld.long 0x18 13. " [13] ,Interrupt Preset bit 13" "Not interrupt,Interrupt" eventfld.long 0x18 12. " [12] ,Interrupt Preset bit 12" "Not interrupt,Interrupt" textline " " eventfld.long 0x18 11. " [11] ,Interrupt Preset bit 11" "Not interrupt,Interrupt" eventfld.long 0x18 10. " [10] ,Interrupt Preset bit 10" "Not interrupt,Interrupt" eventfld.long 0x18 9. " [9] ,Interrupt Preset bit 9" "Not interrupt,Interrupt" eventfld.long 0x18 8. " [8] ,Interrupt Preset bit 8" "Not interrupt,Interrupt" textline " " eventfld.long 0x18 7. " [7] ,Interrupt Preset bit 7" "Not interrupt,Interrupt" eventfld.long 0x18 6. " [6] ,Interrupt Preset bit 6" "Not interrupt,Interrupt" eventfld.long 0x18 5. " [5] ,Interrupt Preset bit 5" "Not interrupt,Interrupt" eventfld.long 0x18 4. " [4] ,Interrupt Preset bit 4" "Not interrupt,Interrupt" textline " " eventfld.long 0x18 3. " [3] ,Interrupt Preset bit 3" "Not interrupt,Interrupt" eventfld.long 0x18 2. " [2] ,Interrupt Preset bit 2" "Not interrupt,Interrupt" eventfld.long 0x18 1. " [1] ,Interrupt Preset bit 1" "Not interrupt,Interrupt" eventfld.long 0x18 0. " [0] ,Interrupt Preset bit 0" "Not interrupt,Interrupt" line.long 0x1C "INTPRESET1,Interrupt Preset Register 1 for interrupt bits" eventfld.long 0x1C 31. " INTPRESET1_[31] ,Interrupt Preset bit 31" "Not interrupt,Interrupt" eventfld.long 0x1C 30. " [30] ,Interrupt Preset bit 30" "Not interrupt,Interrupt" eventfld.long 0x1C 29. " [29] ,Interrupt Preset bit 29" "Not interrupt,Interrupt" eventfld.long 0x1C 28. " [28] ,Interrupt Preset bit 28" "Not interrupt,Interrupt" textline " " eventfld.long 0x1C 27. " [27] ,Interrupt Preset bit 27" "Not interrupt,Interrupt" eventfld.long 0x1C 26. " [26] ,Interrupt Preset bit 26" "Not interrupt,Interrupt" eventfld.long 0x1C 25. " [25] ,Interrupt Preset bit 25" "Not interrupt,Interrupt" eventfld.long 0x1C 24. " [24] ,Interrupt Preset bit 24" "Not interrupt,Interrupt" textline " " eventfld.long 0x1C 23. " [23] ,Interrupt Preset bit 23" "Not interrupt,Interrupt" eventfld.long 0x1C 22. " [22] ,Interrupt Preset bit 22" "Not interrupt,Interrupt" eventfld.long 0x1C 21. " [21] ,Interrupt Preset bit 21" "Not interrupt,Interrupt" eventfld.long 0x1C 20. " [20] ,Interrupt Preset bit 20" "Not interrupt,Interrupt" textline " " eventfld.long 0x1C 19. " [19] ,Interrupt Preset bit 19" "Not interrupt,Interrupt" eventfld.long 0x1C 18. " [18] ,Interrupt Preset bit 18" "Not interrupt,Interrupt" eventfld.long 0x1C 17. " [17] ,Interrupt Preset bit 17" "Not interrupt,Interrupt" eventfld.long 0x1C 16. " [16] ,Interrupt Preset bit 16" "Not interrupt,Interrupt" textline " " eventfld.long 0x1C 15. " [15] ,Interrupt Preset bit 15" "Not interrupt,Interrupt" eventfld.long 0x1C 14. " [14] ,Interrupt Preset bit 14" "Not interrupt,Interrupt" eventfld.long 0x1C 13. " [13] ,Interrupt Preset bit 13" "Not interrupt,Interrupt" eventfld.long 0x1C 12. " [12] ,Interrupt Preset bit 12" "Not interrupt,Interrupt" textline " " eventfld.long 0x1C 11. " [11] ,Interrupt Preset bit 11" "Not interrupt,Interrupt" eventfld.long 0x1C 10. " [10] ,Interrupt Preset bit 10" "Not interrupt,Interrupt" eventfld.long 0x1C 9. " [9] ,Interrupt Preset bit 9" "Not interrupt,Interrupt" eventfld.long 0x1C 8. " [8] ,Interrupt Preset bit 8" "Not interrupt,Interrupt" textline " " eventfld.long 0x1C 7. " [7] ,Interrupt Preset bit 7" "Not interrupt,Interrupt" eventfld.long 0x1C 6. " [6] ,Interrupt Preset bit 6" "Not interrupt,Interrupt" eventfld.long 0x1C 5. " [5] ,Interrupt Preset bit 5" "Not interrupt,Interrupt" eventfld.long 0x1C 4. " [4] ,Interrupt Preset bit 4" "Not interrupt,Interrupt" textline " " eventfld.long 0x1C 3. " [3] ,Interrupt Preset bit 3" "Not interrupt,Interrupt" eventfld.long 0x1C 2. " [2] ,Interrupt Preset bit 2" "Not interrupt,Interrupt" eventfld.long 0x1C 1. " [1] ,Interrupt Preset bit 1" "Not interrupt,Interrupt" eventfld.long 0x1C 0. " [0] ,Interrupt Preset bit 0" "Not interrupt,Interrupt" tree.end width 15. group.long 0x400++0x03 line.long 0x00 "FIFO,FIFO" button "FIFO" "d (ad:0x3A000000+0x400)--(ad:0x3A000000+0x4FF) /long" group.long 0x500++0x03 line.long 0x00 "CONTROL,Message Buffer Control" bitfld.long 0x00 31. " BLOCK_ON_FATAL ,Suppress pending signal when fatal error was detected" "No error,Error" bitfld.long 0x00 2. " R1BUF_BACKPRESSURE_ENABLE ,Enable backpressure when read buffer 1 is running full" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " R0BUF_BACKPRESSURE_ENABLE ,Enable backpressure when read buffer 0 is running full" "Disabled,Enabled" rgroup.long 0x504++0x03 line.long 0x00 "STATUS,Message Buffer Status" bitfld.long 0x00 6. " WDG_TIMEOUT ,Watchdog timeout" "Not timeout,Timeout" bitfld.long 0x00 5. " WRBUF_EMPTY ,Write buffer is empty" "Not empty,Empty" textline " " bitfld.long 0x00 4. " WRBUF_FULL ,Write buffer is full" "Not full,Full" bitfld.long 0x00 3. " R1BUF_EMPTY ,Read buffer 1 is empty" "Not empty,Empty" textline " " bitfld.long 0x00 2. " R1BUF_FULL ,Read buffer 1 is full" "Not full,Full" bitfld.long 0x00 1. " R0BUF_EMPTY ,Read buffer 0 is empty" "Not empty,Empty" textline " " bitfld.long 0x00 0. " R0BUF_FULL ,Read buffer 0 is full" "Not full,Full" group.long 0x508++0x0B line.long 0x00 "CLEAR,Message Buffer Clear" eventfld.long 0x00 2. " R1BUF_CLEAR ,Writing a '1' clears read buffer 1" "-,Clear" eventfld.long 0x00 1. " R0BUF_CLEAR ,Writing a '1' clears read buffer 0" "-,Clear" textline " " eventfld.long 0x00 0. " WRBUF_CLEAR ,Writing a '1' clears write buffer" "-,Clear" line.long 0x04 "DMA_CONTROL,DMA Control" bitfld.long 0x04 24.--25. " DMA2_MODE ,Dma2 mode" "PREVIOUS,LOCAL,BOTH," bitfld.long 0x04 20.--21. " DMA1_MODE ,Dma1 mode" "PREVIOUS,LOCAL,BOTH," textline " " bitfld.long 0x04 16.--17. " DMA0_MODE ,Dma0 mode" "PREVIOUS,LOCAL,BOTH," bitfld.long 0x04 10. " R1BUF_DMA_ENABLE ,Enable DMA for read buffer 1" "Disabled,Enabled" textline " " bitfld.long 0x04 8.--9. " R1BUF_DMA_PORT ,R1buf_dma_port" "0,1,2,3" bitfld.long 0x04 6. " R0BUF_DMA_ENABLE ,Enable DMA for read buffer 0" "Disabled,Enabled" textline " " bitfld.long 0x04 4.--5. " R0BUF_DMA_PORT ,DMA port number for read buffer 0" "0,1,2,3" bitfld.long 0x04 2. " WRBUF_DMA_ENABLE ,Enable DMA for write buffer" "Disabled,Enabled" textline " " bitfld.long 0x04 0.--1. " WRBUF_DMA_PORT ,DMA port number for write buffer" "0,1,2,3" line.long 0x08 "WATCHDOG_LOAD,Watchdog counter preset value" textline "" width 15. group.long 0x600++0x03 line.long 0x00 "RFC,Reframer Control Register" bitfld.long 0x00 14. " INTTX0_MODE ,Configuration inttx0 interrupt behavior" "Frame is programmable,Triggered with leading edge" textline " " bitfld.long 0x00 12.--13. " INTTX2_MODE ,Configuration of interrupt source of inttx2 interrupt" "Not active,HS out-of-sync,VS out-of-sync,HS or VS out-of-sync" textline " " bitfld.long 0x00 0. " RFEN ,Disable/Enable reframer" "Disabled,Enabled" rgroup.long 0x604++0x03 line.long 0x00 "RSR,Reframer Status Register" bitfld.long 0x00 1. " VS_STATE ,Indicates the status of synchronisation of the vertical sync" "Synchronized,Not synchronized" textline " " bitfld.long 0x00 0. " HS_STATE ,Indicates the status of synchronisation of the horizontal sync" "Synchronized,Not synchronized" group.long 0x608++0x2B line.long 0x00 "HTP,Horizontal Total Pixels" hexmask.long.word 0x00 16.--27. 1. " HTP ,Specifies the horizontal total pixel count" line.long 0x04 "HDP,Horizontal Display Period" hexmask.long.word 0x04 0.--11. 1. " HDP ,Specifies the horizontal display period in units of pixel clocks" line.long 0x08 "HSP_HSW_VSW,Horizontal Synchronize pulse PositionHorizontal Synchronize pulse WidthVertical Synchronize pulse Width" bitfld.long 0x08 24.--29. " VSW ,Specifies the pulse width of the vertical synchronization signal in units of rasters" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" textline " " hexmask.long.byte 0x08 16.--23. 1. " HSW ,Specifies the pulse width of the horizontal synchronization signal in units of pixel clocks" textline " " hexmask.long.word 0x08 0.--11. 1. " HSP ,Specifies the pulse position of the horizontal synchronization signal in units of pixel clocks" line.long 0x0C "VTR,Vertical Total Raster" hexmask.long.word 0x0C 16.--27. 1. " VTR ,Specifies the vertical total raster count" line.long 0x10 "VDP_VSP,Vertical Display PeriodVertical Synchronize pulse Position" hexmask.long.word 0x10 16.--27. 1. " VDP ,Specifies the vertical display period in units of rasters" textline " " hexmask.long.word 0x10 0.--11. 1. " VSP ,Specifies the pulse position of the vertical synchronization signal in units of rasters" line.long 0x14 "AGT,Setting of Forward Alignment Guard Time and Backward Alignment Guard Time" bitfld.long 0x14 8.--11. " VBAGT ,Backward alignment guard time for vertical synchronisation in number of vertical sync cycles" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x14 0.--3. " VFAGT ,Forward alignment guard time for vertical synchronisation in number of vertical sync cycles" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x18 "INTTX0TRIGGER,Coordinates of the trigger point for generation of the INT0 interrupt signal" hexmask.long.word 0x18 16.--27. 1. " INTTX0ROW ,Specifies on which row of the display raster the INTTX0 signal is triggered" textline " " hexmask.long.word 0x18 0.--11. 1. " INTTX0COL ,Specifies on which column of the display raster the INTTX0 signal is triggered" line.long 0x1C "INTTX1TRIGGER,Coordinates of the trigger point for generation of the INT1 interrupt signal" hexmask.long.word 0x1C 16.--27. 1. " INTTX1ROW ,Specifies on which row of the display raster the INTTX1 signal is triggered" textline " " hexmask.long.word 0x1C 0.--11. 1. " INTTX1COL ,Specifies on which column of the display raster the INTTX1 signal is triggered" line.long 0x20 "RESYNCMODE,Program features of resynchronization mode" bitfld.long 0x20 25. " EVEN_FP ,Enable even number of pixels for horizontal front porch" "Disabled,Enabled" textline " " bitfld.long 0x20 24. " ADJUST_LINE ,Enable alignment mode to odd or even number of pixel for horizontal front porch" "Disabled,Enablded" textline " " hexmask.long.byte 0x20 8.--15. 1. " VSP_START ,Initial value of vertical front porch down counter" textline " " hexmask.long.byte 0x20 0.--7. 1. " HSP_START ,Initial value of horizontal front porch down counter" line.long 0x24 "CHPOLARITY,Change Polarity of video sync signals on rx (input) and tx (output) side" bitfld.long 0x24 6. " VS_TX ,Change polarity of signal 'vertical sync' on tx (output) side" "Active low,Active high" textline " " bitfld.long 0x24 5. " HS_TX ,Change polarity of signal 'horizontal sync' on tx (output) side" "Active low,Active high" textline " " bitfld.long 0x24 4. " DE_TX ,Change polarity of signal 'data enable' on tx (output) side" "Active high,Active low" textline " " bitfld.long 0x24 2. " VS_RX ,Change polarity of signal 'vertical sync' on rx (input) side" "Active low,Active high" textline " " bitfld.long 0x24 1. " HS_RX ,Change polarity of signal 'horizontal sync' on rx (input) side" "Active low,Active high" textline " " bitfld.long 0x24 0. " DE_RX ,Change polarity of signal 'data enable' on rx (input) side" "Active high,Active low" line.long 0x28 "TIMINGDELAY,Delay external (rx) synchronisation signals HSYNC and VSYNC" hexmask.long.word 0x28 16.--26. 1. " VSTIMDELAY ,Delay external (rx) synchronisation signals VSYNC" textline " " hexmask.long.word 0x28 0.--10. 1. " HSTIMDELAY ,Delay external (rx) synchronisation signals HSYNC" textline " " width 35. group.long 0x644++0x03 line.long 0x00 "I2C_OUTBOUND_JOB_SPEC_STATUS,I2C_Outbound_Job_Spec_Status" eventfld.long 0x00 31. " I2C_OUTBOUND_JOB_SPEC_CLEAR ,I2C_Outbound_Job_Spec_Clear" "-,Clear" textline " " rbitfld.long 0x00 0. " I2C_OUTBOUND_JOB_SPEC_BUSY ,I2C_Outbound_Job_Spec_Busy" "Not busy,Busy" group.long 0x648++0x07 line.long 0x00 "I2C_OUTBOUND_JOB_SPEC_DATA_LOW,I2C_Outbound_Job_Spec_Data_Low" line.long 0x04 "I2C_OUTBOUND_JOB_SPEC_DATA_HIGH,I2C_Outbound_Job_Spec_Data_High" rgroup.long 0x650++0x0B line.long 0x00 "I2C_INBOUND_JOB_SPEC_STATUS,I2C_Inbound_Job_Spec_Status" rbitfld.long 0x00 0. " I2C_INBOUND_JOB_SPEC_VALID ,I2C_Inbound_Job_Spec_Valid" "No,Yes" line.long 0x04 "I2C_INBOUND_JOB_SPEC_L,I2C_Inbound_Job_spec_l" line.long 0x08 "I2C_INBOUND_JOB_SPEC_H,I2C_Inbound_Job_spec_h" group.long 0x65C++0x03 line.long 0x00 "I2C_INBOUND_JOB_SPEC_ERROR,I2C_Inbound_Job_Spec_Error" bitfld.long 0x00 31. " I2C_INBOUND_JOB_SPEC_ERROR ,I2C_Inbound_Job_Spec_Error" "No error,Error" group.long 0x660++0x07 line.long 0x00 "I2C_OUTBOUND_STATUS,I2C_Outbound_Status" eventfld.long 0x00 31. " I2C_OUTBOUND_STATUS_CLEAR ,I2C_Outbound_Status_Clear" "-,Clear" textline " " rbitfld.long 0x00 0. " I2C_OUTBOUND_STATUS_BUSY ,I2C_Outbound_Status_Busy" "Not busy,Busy" line.long 0x04 "I2C_OUTBOUND_STATUS_DATA,I2C_Outbound_Status_Data" bitfld.long 0x04 3. " I2C_OUTBOUND_STATUS_ALOST_DETECTED ,I2C bus arbitration status" "No arbitration,Arbitration" textline " " bitfld.long 0x04 2. " I2C_OUTBOUND_STATUS_NACK_DETECTED ,I2C_Outbound_Status_Nack_Detected" "No occurred,Occurred" textline " " bitfld.long 0x04 1. " I2C_OUTBOUND_STATUS_JOB_CACC ,I2C_Outbound_Status_Job_Cacc" "No canceled,Canceled" textline " " bitfld.long 0x04 0. " I2C_OUTBOUND_STATUS_JOB_DONE ,I2C_Outbound_Status_Job_Done" "0,1" group.long 0x668++0x03 line.long 0x00 "I2C_INBOUND_STATUS,I2C_Inbound_Status" rbitfld.long 0x00 0. " I2C_INBOUND_STATUS_VALID ,I2C_Inbound_Status_Valid" "No,Yes" group.long 0x66C++0x0B line.long 0x00 "I2C_INBOUND_STATUS_DATA,I2C_Inbound_Status_Data" bitfld.long 0x00 31. " I2C_INBOUND_STATUS_ERROR ,I2C_Inbound_Status_Error" "No error,Error" textline " " rbitfld.long 0x00 3. " I2C_INBOUND_STATUS_ALOST_DETECTED ,I2C_Inbound_Status_Alost_detected" "Not detected,Detected" textline " " rbitfld.long 0x00 2. " I2C_INBOUND_STATUS_NACK_DETECTED ,I2C_Inbound_Status_Nack_detected" "Not detected,Detected" textline " " rbitfld.long 0x00 1. " I2C_INBOUND_STATUS_JOB_CACC ,I2C_Inbound_Status_Job_cacc" "0,1" textline " " rbitfld.long 0x00 0. " I2C_INBOUND_STATUS_JOB_DONE ,I2C_Inbound_Status_Job_done" "0,1" line.long 0x04 "I2C_OUTBOUND_READ_RESPONSE_STATUS,I2C_Outbound_Read_Response_Status" eventfld.long 0x04 31. " I2C_OUTBOUND_READ_RESPONSE_CLEAR ,I2C_Outbound_Read_Response_Clear" "-,Clear" textline " " rbitfld.long 0x04 0. " I2C_OUTBOUND_READ_RESPONSE_BUSY ,I2C_Outbound_Read_Response_Busy" "Not busy,Busy" line.long 0x08 "I2C_OUTBOUND_READ_RESPONSE_DATA,I2C_Outbound_Read_Response_Data" hexmask.long.byte 0x08 0.--7. 1. " I2C_OUTBOUND_READ_RESPONSE_DATA ,I2C_Outbound_Read_Response_Data" rgroup.long 0x678++0x03 line.long 0x00 "I2C_INBOUND_READ_RESPONSE_STATUS,I2C_Inbound_Read_Response_Status" rbitfld.long 0x00 0. " I2C_INBOUND_READ_RESPONSE_VALID ,I2C_Inbound_Read_Response_Valid" "No,Yes" group.long 0x67C++0x0B line.long 0x00 "I2C_INBOUND_READ_RESPONSE_DATA,I2C_Inbound_Read_Response_Data" bitfld.long 0x00 31. " I2C_INBOUND_READ_RESPONSE_ERROR ,I2C_Inbound_Read_Response_Error" "No error,Error" textline " " rbitfld.long 0x00 8.--10. " I2C_INBOUND_READ_RESPONSE_DATA_NUM ,I2C_Inbound_Read_Response_Data_Num" "0,1,2,3,4,5,6,7" textline " " hexmask.long.byte 0x00 0.--7. 1. " I2C_INBOUND_READ_RESPONSE_DATA ,I2C_Inbound_Read_Response_Data" line.long 0x04 "REMOTE_CONTROLLER_OUTBOUND_STATUS,Remote_Controller_Outbound_Status" eventfld.long 0x04 31. " REMOTE_CONTROLLER_OUTBOUND_CLEAR ,Remote_Controller_Outbound_Clear" "No busy,Busy" textline " " rbitfld.long 0x04 0. " REMOTE_CONTROLLER_OUTBOUND_BUSY ,Remote_Controller_Outbound_Busy" "-,Clear" line.long 0x08 "REMOTE_CONTROLLER_OUTBOUND_DATA,Remote_Controller_Outbound_Data" hexmask.long.byte 0x08 8.--15. 1. " REMOTE_CONTROLLER_OUTBOUND_DATA ,Remote_Controller_Outbound_Data" textline " " bitfld.long 0x08 7. " REMOTE_CONTROLLER_OUTBOUND_RW ,Remote_Controller_Outbound_RW" "0,1" textline " " hexmask.long.byte 0x08 0.--6. 1. " REMOTE_CONTROLLER_OUTBOUND_ADDRESS ,Remote_Controller_Outbound_Address" rgroup.long 0x688++0x03 line.long 0x00 "REMOTE_CONTROLLER_INBOUND_STATUS,Remote_Controller_Inbound_Status" bitfld.long 0x00 0. " REMOTE_CONTROLLER_INBOUND_VALID ,Remote_Controller_Inbound_Valid" "No,Yes" group.long 0x68C++0x03 line.long 0x00 "REMOTE_CONTROLLER_INBOUND_DATA,Remote_Controller_Inbound_Data" bitfld.long 0x00 31. " REMOTE_CONTROLLER_INBOUND_ERROR ,Remote_Controller_Inbound_Error" "No error,Error" textline " " hexmask.long.byte 0x00 0.--7. 1. " REMOTE_CONTROLLER_INBOUND_RESPONSE_DATA ,Remote_Controller_Inbound_Response_Data" rgroup.long 0x690++0x03 line.long 0x00 "REMOTE_SERVICE_INBOUND_STATUS,Remote_Service_Inbound_Status" bitfld.long 0x00 0. " REMOTE_SERVICE_INBOUND_VALID ,Remote_Service_Inbound_Valid" "No,Yes" group.long 0x694++0x13 line.long 0x00 "REMOTE_SERVICE_INBOUND_DATA,Remote_Service_Inbound_Data" bitfld.long 0x00 31. " REMOTE_SERVICE_INBOUND_ERROR ,Remote_Service_Inbound_Error" "No error,Error" textline " " hexmask.long.byte 0x00 8.--15. 1. " REMOTE_SERVICE_INBOUND_DATA ,Remote_Service_Inbound_Data" textline " " rbitfld.long 0x00 7. " REMOTE_SERVICE_INBOUND_RW ,Remote_Service_Inbound_RW" "0,1" textline " " hexmask.long.byte 0x00 0.--6. 1. " REMOTE_SERVICE_INBOUND_ADDRESS ,Remote_Service_Inbound_Address" line.long 0x04 "REMOTE_SERVICE_OUTBOUND_STATUS,Remote_Service_Outbound_Status" eventfld.long 0x04 31. " REMOTE_SERVICE_OUTBOUND_CLEAR ,Remote_Service_Outbound_Clear" "-,Clear" textline " " rbitfld.long 0x04 0. " REMOTE_SERVICE_OUTBOUND_BUSY ,Remote_Service_Outbound_Busy" "Not busy,Busy" line.long 0x08 "REMOTE_SERVICE_OUTBOUND_DATA,Remote_Service_Outbound_Data" hexmask.long.byte 0x08 0.--7. 1. " REMOTE_SERVICE_OUTBOUND_READ_RESPONSE_DATA ,Remote_Service_Outbound_Read_Response_Data" line.long 0x0C "REMOTE_COMMAND_OUTBOUND_STATUS,Remote_Command_Outbound_Status" eventfld.long 0x0C 31. " REMOTE_COMMAND_OUTBOUND_CLEAR ,Remote_Command_Outbound_Clear" "-,Clear" textline " " rbitfld.long 0x0C 0. " REMOTE_COMMAND_OUTBOUND_BUSY ,Remote_Command_Outbound_Busy" "Not busy,Busy" line.long 0x10 "REMOTE_COMMAND_OUTBOUND_DATA,Remote_Command_Outbound_Data" bitfld.long 0x10 3. " REMOTE_COMMAND_OUTBOUND_JOB_CANCEL ,Remote_Command_Outbound_Job_Cancel" "Not set,Set" textline " " bitfld.long 0x10 2. " REMOTE_COMMAND_OUTBOUND_CLEAR_TICKET_COUNTER ,Remote_Command_Outbound_Clear_Ticket_Counter" "-,Clear" textline " " bitfld.long 0x10 1. " REMOTE_COMMAND_OUTBOUND_REALIGN ,Remote_Command_Outbound_Realign" "Not Realign,Realign" textline " " bitfld.long 0x10 0. " REMOTE_COMMAND_OUTBOUND_SOFT_RESET ,Remote_Command_Outbound_Soft_Reset" "Not reset,Reset" width 12. tree.end tree "APIX_PHY" base ad:0x3A000000 width 18. group.long 0x700++0x07 line.long 0x00 "PHY_RESET,Phy reset" bitfld.long 0x00 1. " PLL_RESET_N ,Pll_reset_n" "Reset,Operational" bitfld.long 0x00 0. " PHY_RESET_N ,Phy_reset_n" "Reset,Operational" line.long 0x04 "PHY_POWER_CTRL,Phy power control" bitfld.long 0x04 26. " TX0POWER_ON ,Power on tx0 macro" "Off,On" bitfld.long 0x04 25. " TX1POWER_ON ,Power on tx1 macro" "Off,On" textline " " bitfld.long 0x04 24. " TX2POWER_ON ,Power on tx2 macro" "Off,On" bitfld.long 0x04 18. " TX0CLKBUF_ON ,Power on clock buffer in tx0" "Off,On" textline " " bitfld.long 0x04 17. " TX1CLKBUF_ON ,Power on clock buffer in tx1" "Off,On" bitfld.long 0x04 16. " TX2CLKBUF_ON ,Power on clock buffer in tx2" "Off,On" textline " " bitfld.long 0x04 10. " MCLK_POWER_ON ,Power on synthesized clock" "Off,On" bitfld.long 0x04 9. " RXUP_POWER_ON ,Power on Receiver upstream" "Off,On" textline " " bitfld.long 0x04 8. " RX_POWER_ON ,Power on Receiver" "Off,On" bitfld.long 0x04 0.--5. " RLL_POWER_ON ,Power Control for PLL" "Off,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,On" group.long 0x714++0x03 line.long 0x00 "PLL_STATUS_CLEAR,PLL status clear" eventfld.long 0x00 0. " PLLERRCNTCLEAR ,Clear PLLErrCnt by writing a 1" "Not clear,Clear" if (((per.l(ad:0x3A000000+0x100))&0x01)==0x01) group.long 0x718++0x03 line.long 0x00 "PLL_STS,PLL_sts" bitfld.long 0x00 8.--13. " PLLERRCNT ,PLL error counter[5:0]" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" rbitfld.long 0x00 0. " PLLGOOD ,PLL locked" "0,1" else hgroup.long 0x718++0x03 hide.long 0x00 "PLL_STS,PLL_sts" endif group.long 0x878++0x0F line.long 0x00 "TIMER_CFG,Timer Configuration Register needed e.g. for calibration" bitfld.long 0x00 1. " TIMER_SEL16MS ,Timer cycle select" "1ms,16ms" bitfld.long 0x00 0. " TIMER_EN ,Enable timer" "Disabled,Enabled" line.long 0x04 "CAL_CFG,Calibration Configuration Register" bitfld.long 0x04 8.--10. " SEL_CAL ,Select calibration input and method" "OVERR/Signal rx_cfg,DAT0/Signal tx0,DAT1/Signal tx1,DAT2/Signal tx2,,,," line.long 0x08 "TRIG_CFG,Trigger Configuration Register needed e.g. for calibration" bitfld.long 0x08 16. " TRIG_HW_SRC ,Select HW trigger source" "TIMER Timer,IPIN Input-Pin" hexmask.long.word 0x08 0.--9. 1. " TRIG_SEL ,Selects hardware trigger source for trigger pin9..0" line.long 0x0C "TRIG_ACTV,Trigger Activation Register needed e.g. for calibration" hexmask.long.word 0x0C 0.--9. 1. " TRIG_ACTV ,Write 1 to respective bit to send a trigger pulse 16 AHB clock cycles long" width 0xb tree.end endif tree "AXI (Bus Interconnect)" base ad:0xD0000000 width 20. group.long 0x42100++0x03 line.long 0x00 "DISP0_READ_QOS,Display0 read priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x43100++0x03 line.long 0x00 "DISP1_READ_QOS,Display1 read priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x44100++0x03 line.long 0x00 "DISP2_READ_QOS,Display2 read priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x45104++0x03 line.long 0x00 "CAP0_WRITE_QOS,Capture0 write priority(QOS)" bitfld.long 0x00 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x46104++0x03 line.long 0x00 "CAP1_WRITE_QOS,Capture1 write priority(QOS)" bitfld.long 0x00 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x47104++0x03 line.long 0x00 "CAP2_WRITE_QOS,Capture2 write priority(QOS)" bitfld.long 0x00 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x48104++0x03 line.long 0x00 "CAP3_WRITE_QOS,Capture3 write priority(QOS)" bitfld.long 0x00 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x49040++0x03 line.long 0x00 "COMSEQ1_TIDEMARK,This register sets how many data to straighten to FIFO" bitfld.long 0x00 0.--3. " Wr_tidemark ,Wr_tidemark" "Non buffering,,,,Buffering FIFO,,,,,,,,,,," group.long 0x49100++0x03 line.long 0x00 "COMSEQ1_READ_QOS,COMSEQ1_READ_QOS" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x49104++0x03 line.long 0x00 "COMSEQ1_WRITE_QOS,COMSEQ1_WRITE_QOS" bitfld.long 0x00 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x4A104++0x03 line.long 0x00 "WB_WRITE_QOS,WriteBack write priority(QOS)" bitfld.long 0x00 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x4C100++0x03 line.long 0x00 "3DGE_0_READ_QOS,3DGE master#0 read priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x4C104++0x03 line.long 0x00 "3DGE_0_WRITE_QOS,3DGE master#0 write priority(QOS)" bitfld.long 0x00 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x4D100++0x07 line.long 0x00 "3DGE_1_READ_QOS,3DGE master#1 read priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" line.long 0x04 "3DGE_1_WRITE_QOS,3DGE master#1 write priority(QOS)" bitfld.long 0x04 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x4E100++0x07 line.long 0x00 "3DGE_2_READ_QOS,3DGE master#2 read priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" line.long 0x04 "3DGE_2_WRITE_QOS,3DGE master#2 write priority(QOS)" bitfld.long 0x04 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x4F100++0x03 line.long 0x00 "PIXENG_r0_READ_QOS,Pixel Engine read master#0 priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x50100++0x03 line.long 0x00 "PIXENG_r1_READ_QOS,Pixel Engine read master#1 priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x51100++0x03 line.long 0x00 "PIXENG_r2_READ_QOS,Pixel Engine read master#2 priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x52104++0x03 line.long 0x00 "PIXENG_w_WRITE_QOS,Pixel Engine write master priority(QOS)" bitfld.long 0x00 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x53100++0x07 line.long 0x00 "CPU_0_READ_QOS,CPU(Cortex-A9) master#0 read priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" line.long 0x04 "CPU_0_WRITE_QOS,CPU(Cortex-A9) master#0 write Priority(QOS)" bitfld.long 0x04 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x54100++0x07 line.long 0x00 "CPU_1_READ_QOS,CPU(Cortex-A9) master#1 read priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" line.long 0x04 "CPU_1_WRITE_QOS,CPU(Cortex-A9) master#1 write priority(QOS)" bitfld.long 0x04 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x55100++0x07 line.long 0x00 "XDMAC_READ_QOS,XDMAC master read priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" line.long 0x04 "XDMAC_WRITE_QOS,XDMAC master write priority(QOS)" bitfld.long 0x04 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x56040++0x03 line.long 0x00 "COMSEQ0_TIDEMARK,This register sets how many data to straighten to FIFO" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Non buffering,,,,Buffering FIFO,,,,,,,,,,," group.long 0x56100++0x07 line.long 0x00 "COMSEQ0_READ_QOS,Command Sequencer 0 master read priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" line.long 0x04 "COMSEQ0_WRITE_QOS,Command Sequencer 0 master write priority(QOS)" bitfld.long 0x04 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x57100++0x07 line.long 0x00 "AHB_0_READ_QOS,AHB_0 master read priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" line.long 0x04 "AHB_0_WRITE_QOS,AHB_0 master write priority(QOS)" bitfld.long 0x04 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x58100++0x07 line.long 0x00 "AHB_1_READ_QOS,AHB_1 master read priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" line.long 0x04 "AHB_1_WRITE_QOS,AHB_1 master write priority(QOS)" bitfld.long 0x04 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" group.long 0x59100++0x07 line.long 0x00 "TS_READ_QOS,TS master read priority(QOS)" bitfld.long 0x00 0.--3. " Read_qos ,Read_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" line.long 0x04 "TS_WRITE_QOS,TS master write priority(QOS)" bitfld.long 0x04 0.--3. " Write_qos ,Write_qos" "Low priority,1,2,3,4,5,6,7,8,9,10,11,12,13,14,High priority" base ad:0xD0400000 group.long 0x00++0x0B line.long 0x00 "PortSet0,DDR Port Setting register 0" bitfld.long 0x00 24. " CAP3W ,DDR Memory Write Port(Capture3)" "Port 0,Port 1" bitfld.long 0x00 20. " CAP2W ,DDR Memory Write Port(Capture2)" "Port 0,Port 1" textline " " bitfld.long 0x00 16. " CAP1W ,DDR Memory Write Port(Capture1)" "Port 0,Port 1" bitfld.long 0x00 12. " CAP0W ,DDR Memory Write Port(Capture0)" "Port 0,Port 1" textline " " bitfld.long 0x00 8. " DISP2R ,DDR Memory Read Port(Display2)" "Port 0,Port 1" bitfld.long 0x00 4. " DISP1R ,DDR Memory Read Port(Display1)" "Port 0,Port 1" textline " " bitfld.long 0x00 0. " DISP0R ,DDR Memory Read Port(Display0)" "Port 0,Port 1" line.long 0x04 "PortSet1,DDR Port setting register 1" bitfld.long 0x04 24. " PIXW ,DDR Memory Write Port(Pixel Engine Write)" "Port 2,Port 3" bitfld.long 0x04 20. " PIXR2 ,DDR Memory Read Port(Pixel Engine Read 2)" "Port 2,Port 3" textline " " bitfld.long 0x04 16. " PIXR1 ,DDR Memory Read Port(Pixel Engine Read 1)" "Port 2,Port 3" bitfld.long 0x04 12. " PIXR0 ,DDR Memory Read Port(Pixel Engine Read 0)" "Port 2,Port 3" textline " " bitfld.long 0x04 0. " WBW ,DDR Memory Write Port(Writeback)" "Port 0,Port 1" line.long 0x08 "PortSet2,DDR Port setting register 2" bitfld.long 0x08 20. " 3DGE2W ,DDR Memory Write Port(3DGE Master2)" "Port 2,Port 3" bitfld.long 0x08 16. " 3DGE2R ,DDR Memory Read Port(3DGE Master2)" "Port 2,Port 3" textline " " bitfld.long 0x08 12. " 3DGE1W ,DDR Memory Write Port(3DGE Master1)" "Port 2,Port 3" bitfld.long 0x08 8. " 3DGE1R ,DDR Memory Read Port(3DGE Master1)" "Port 2,Port 3" textline " " bitfld.long 0x08 4. " 3DGE0W ,DDR Memory Write Port(3DGE Master0)" "Port 2,Port 3" bitfld.long 0x08 0. " 3DGE0R ,DDR Memory Read Port(3DGE Master0)" "Port 2,Port 3" width 0xb tree.end sif (cpu()=="MB86R11F") tree "CAN" tree "CAN ch0" base ad:0x3E100000 width 9. group.byte 0x20++0x00 line.byte 0x00 "CCNTRL,MCAN Control Register" bitfld.byte 0x00 7. " MODE ,Undefined mode" "Mode off,Mode on" bitfld.byte 0x00 6. " SPD ,Speed mode" "Slow,Fast" bitfld.byte 0x00 4. " OIE ,Overrun interrupt enable" "Disabled,Enabled" bitfld.byte 0x00 3. " EIE ,Error interrupt enable" "Disabled,Enabled" textline " " bitfld.byte 0x00 2. " TIE ,Transmit interrupt enable" "Disabled,Enabled" bitfld.byte 0x00 1. " RIE ,Receive interrupt enable" "Disabled,Enabled" bitfld.byte 0x00 0. " RR ,Reset request" "No reset,Reset" if ((((per.b((ad:0x3E100000+0x20))&0x01))==0x00)) wgroup.byte 0x21++0x00 line.byte 0x00 "CCOM,MCAN Command Register" bitfld.byte 0x00 7. " RX0 ,Receive pin 0" " RX0 ,VDD/2" bitfld.byte 0x00 6. " RX1 ,Receive pin 1" "RX0,VDD/2" bitfld.byte 0x00 5. " COMPSEL ,Comparator selector" "RX0/1 with VDD/2,RX0 with RX1" bitfld.byte 0x00 4. " SLEEP ,Sleep mode off/on" "Mode off,Mode On" textline " " bitfld.byte 0x00 3. " COS ,Clear overrun status" "No action,Clear" bitfld.byte 0x00 2. " RRB ,Release receive buffer" "Not released,Released" bitfld.byte 0x00 1. " AT ,Abort transmission" "No action,Abort" bitfld.byte 0x00 0. " TR ,Transmission request" "Not requested,Requested" else hgroup.byte 0x21++0x00 hide.byte 0x00 "CCOM,MCAN Command Register" endif rgroup.byte 0x22++0x00 line.byte 0x00 "CSTAT,MCAN Status Register" bitfld.byte 0x00 7. " BS ,Bus status" "On,Off" bitfld.byte 0x00 6. " ES ,Error status" "No error,Error" bitfld.byte 0x00 5. " TS ,Transmit status" "Idle,Transmit" bitfld.byte 0x00 4. " RS ,Receive status" "Idle,Receive" textline " " bitfld.byte 0x00 3. " TCS ,Transmission complete status" "Not completed,Completed" bitfld.byte 0x00 2. " TBA ,Transmit buffer access" "Locked,Released" bitfld.byte 0x00 1. " DO ,Data overrun" "Normal operation,Overrun" bitfld.byte 0x00 0. " RBS ,Receive buffer status" "Empty,Full" hgroup.byte 0x23++0x00 hide.byte 0x00 "CINT,MCAN Interrupt Register" in if ((((per.b((ad:0x3E100000+0x20))&0x01))==0x01)) group.byte 0x24++0x00 line.byte 0x00 "CACC,MCAN Acceptance Code Register" group.byte 0x05++0x0 line.byte 0x00 "CACM,MCAN Acceptance Mask Register" bitfld.byte 0x00 7. " AM_[7] ,Acceptance mask bit 7" "Match,Ignore" bitfld.byte 0x00 6. " [6] ,Acceptance mask bit 6" "Match,Ignore" bitfld.byte 0x00 5. " [5] ,Acceptance mask bit 5" "Match,Ignore" bitfld.byte 0x00 4. " [4] ,Acceptance mask bit 4" "Match,Ignore" textline " " bitfld.byte 0x00 3. " [3] ,Acceptance mask bit 3" "Match,Ignore" bitfld.byte 0x00 2. " [2] ,Acceptance mask bit 2" "Match,Ignore" bitfld.byte 0x00 1. " [1] ,Acceptance mask bit 1" "Match,Ignore" bitfld.byte 0x00 0. " [0] ,Acceptance mask bit 0" "Match,Ignore" group.byte 0x26++0x00 line.byte 0x00 "CBT0,MCAN Bus Timing Register 0" bitfld.byte 0x00 6.--7. " SJW1 ,Synchronization jump width bits" "1 cycle,2cycles,3cycles,4cycles" bitfld.byte 0x00 0.--5. " BRP ,Baud rate prescaler bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" group.byte 0x27++0x00 line.byte 0x00 "CBT1,MCAN Bus Timing Register 1" bitfld.byte 0x00 7. " SAMP_[7] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" bitfld.byte 0x00 6. " [6] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" bitfld.byte 0x00 5. " [5] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" bitfld.byte 0x00 4. " [4] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" textline " " bitfld.byte 0x00 3. " [3] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" bitfld.byte 0x00 2. " [2] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" bitfld.byte 0x00 1. " [1] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" bitfld.byte 0x00 0. " [0] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" group.byte 0x28++0x00 line.byte 0x00 "COCNTRL,MCAN Output Control Register" bitfld.byte 0x00 7. " OCTP1 ,P-type output control transistors enable" "Disabled,Enabled" bitfld.byte 0x00 6. " OCTN1 ,N-type output control transistor enable" "Disabled,Enabled" bitfld.byte 0x00 5. " OCPOL1 ,Driver output polarity" "Low,High" bitfld.byte 0x00 4. " OCTP0 ,P-type output control transistors enable" "Disabled,Enabled" bitfld.byte 0x00 3. " OCTN0 ,N-type output control transistor enable" "Disabled,Enabled" bitfld.byte 0x00 2. " OCPOL0 ,Driver output polarity" "Low,High" bitfld.byte 0x00 0.--1. " OCM ,Output control mode bits" "Biphase,,Mode 1,Mode 2" else hgroup.byte 0x24++0x04 hide.byte 0x00 "CACC,MCAN Acceptance Code Register" hide.byte 0x01 "CACM,MCAN Acceptance Mask Register" hide.byte 0x02 "CBT0,MCAN Bus Timing Register 0" hide.byte 0x03 "CBT1,MCAN Bus Timing Register 1" hide.byte 0x04 "COCNTRL,MCAN Output Control Register" endif group.byte 0x2A++0x1 line.byte 0x00 "TBI,Transmit Buffer Identifier Register" line.byte 0x01 "TRTDL,Remote Transmission Request and Data Length Code Register" bitfld.byte 0x01 5.--7. " ID ,Identifier bits" "0,1,2,3,4,5,6,7" bitfld.byte 0x01 4. " RTR ,Remote transmission request" "Remote,Data" bitfld.byte 0x01 0.--3. " DLC ,Data length code bits" "0,1,2,3,4,5,6,7,8,..." group.byte 0x2C++0x00 line.byte 0x00 "TDS1,Transmit Data Segment 1" group.byte 0x2D++0x00 line.byte 0x00 "TDS2,Transmit Data Segment 2" group.byte 0x2E++0x00 line.byte 0x00 "TDS3,Transmit Data Segment 3" group.byte 0x2F++0x00 line.byte 0x00 "TDS4,Transmit Data Segment 4" group.byte 0x30++0x00 line.byte 0x00 "TDS5,Transmit Data Segment 5" group.byte 0x31++0x00 line.byte 0x00 "TDS6,Transmit Data Segment 6" group.byte 0x32++0x00 line.byte 0x00 "TDS7,Transmit Data Segment 7" group.byte 0x33++0x00 line.byte 0x00 "TDS8,Transmit Data Segment 8" group.byte 0x34++0x01 line.byte 0x00 "RBI,Receive Buffer Identity" line.byte 0x01 "RRTDL,RemoteTtransmission Request and Data Length Code Register" bitfld.byte 0x01 5.--7. " ID ,Identifier bits" "0,1,2,3,4,5,6,7" bitfld.byte 0x01 4. " RTR ,Remote transmission request" "Remote,Data" bitfld.byte 0x01 0.--3. " DLC ,Data length code bits" "0,1,2,3,4,5,6,7,8,..." group.byte 0x36++0x00 line.byte 0x00 "TDS1,Transmit Data Segment 1" group.byte 0x37++0x00 line.byte 0x00 "TDS2,Transmit Data Segment 2" group.byte 0x38++0x00 line.byte 0x00 "TDS3,Transmit Data Segment 3" group.byte 0x39++0x00 line.byte 0x00 "TDS4,Transmit Data Segment 4" group.byte 0x3A++0x00 line.byte 0x00 "TDS5,Transmit Data Segment 5" group.byte 0x3B++0x00 line.byte 0x00 "TDS6,Transmit Data Segment 6" group.byte 0x3C++0x00 line.byte 0x00 "TDS7,Transmit Data Segment 7" group.byte 0x3D++0x00 line.byte 0x00 "TDS8,Transmit Data Segment 8" width 0xb tree.end tree "CAN ch1" base ad:0x3E110000 width 9. group.byte 0x20++0x00 line.byte 0x00 "CCNTRL,MCAN Control Register" bitfld.byte 0x00 7. " MODE ,Undefined mode" "Mode off,Mode on" bitfld.byte 0x00 6. " SPD ,Speed mode" "Slow,Fast" bitfld.byte 0x00 4. " OIE ,Overrun interrupt enable" "Disabled,Enabled" bitfld.byte 0x00 3. " EIE ,Error interrupt enable" "Disabled,Enabled" textline " " bitfld.byte 0x00 2. " TIE ,Transmit interrupt enable" "Disabled,Enabled" bitfld.byte 0x00 1. " RIE ,Receive interrupt enable" "Disabled,Enabled" bitfld.byte 0x00 0. " RR ,Reset request" "No reset,Reset" if ((((per.b((ad:0x3E110000+0x20))&0x01))==0x00)) wgroup.byte 0x21++0x00 line.byte 0x00 "CCOM,MCAN Command Register" bitfld.byte 0x00 7. " RX0 ,Receive pin 0" " RX0 ,VDD/2" bitfld.byte 0x00 6. " RX1 ,Receive pin 1" "RX0,VDD/2" bitfld.byte 0x00 5. " COMPSEL ,Comparator selector" "RX0/1 with VDD/2,RX0 with RX1" bitfld.byte 0x00 4. " SLEEP ,Sleep mode off/on" "Mode off,Mode On" textline " " bitfld.byte 0x00 3. " COS ,Clear overrun status" "No action,Clear" bitfld.byte 0x00 2. " RRB ,Release receive buffer" "Not released,Released" bitfld.byte 0x00 1. " AT ,Abort transmission" "No action,Abort" bitfld.byte 0x00 0. " TR ,Transmission request" "Not requested,Requested" else hgroup.byte 0x21++0x00 hide.byte 0x00 "CCOM,MCAN Command Register" endif rgroup.byte 0x22++0x00 line.byte 0x00 "CSTAT,MCAN Status Register" bitfld.byte 0x00 7. " BS ,Bus status" "On,Off" bitfld.byte 0x00 6. " ES ,Error status" "No error,Error" bitfld.byte 0x00 5. " TS ,Transmit status" "Idle,Transmit" bitfld.byte 0x00 4. " RS ,Receive status" "Idle,Receive" textline " " bitfld.byte 0x00 3. " TCS ,Transmission complete status" "Not completed,Completed" bitfld.byte 0x00 2. " TBA ,Transmit buffer access" "Locked,Released" bitfld.byte 0x00 1. " DO ,Data overrun" "Normal operation,Overrun" bitfld.byte 0x00 0. " RBS ,Receive buffer status" "Empty,Full" hgroup.byte 0x23++0x00 hide.byte 0x00 "CINT,MCAN Interrupt Register" in if ((((per.b((ad:0x3E110000+0x20))&0x01))==0x01)) group.byte 0x24++0x00 line.byte 0x00 "CACC,MCAN Acceptance Code Register" group.byte 0x05++0x0 line.byte 0x00 "CACM,MCAN Acceptance Mask Register" bitfld.byte 0x00 7. " AM_[7] ,Acceptance mask bit 7" "Match,Ignore" bitfld.byte 0x00 6. " [6] ,Acceptance mask bit 6" "Match,Ignore" bitfld.byte 0x00 5. " [5] ,Acceptance mask bit 5" "Match,Ignore" bitfld.byte 0x00 4. " [4] ,Acceptance mask bit 4" "Match,Ignore" textline " " bitfld.byte 0x00 3. " [3] ,Acceptance mask bit 3" "Match,Ignore" bitfld.byte 0x00 2. " [2] ,Acceptance mask bit 2" "Match,Ignore" bitfld.byte 0x00 1. " [1] ,Acceptance mask bit 1" "Match,Ignore" bitfld.byte 0x00 0. " [0] ,Acceptance mask bit 0" "Match,Ignore" group.byte 0x26++0x00 line.byte 0x00 "CBT0,MCAN Bus Timing Register 0" bitfld.byte 0x00 6.--7. " SJW1 ,Synchronization jump width bits" "1 cycle,2cycles,3cycles,4cycles" bitfld.byte 0x00 0.--5. " BRP ,Baud rate prescaler bits" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63" group.byte 0x27++0x00 line.byte 0x00 "CBT1,MCAN Bus Timing Register 1" bitfld.byte 0x00 7. " SAMP_[7] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" bitfld.byte 0x00 6. " [6] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" bitfld.byte 0x00 5. " [5] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" bitfld.byte 0x00 4. " [4] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" textline " " bitfld.byte 0x00 3. " [3] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" bitfld.byte 0x00 2. " [2] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" bitfld.byte 0x00 1. " [1] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" bitfld.byte 0x00 0. " [0] ,This bit determines the number of samples of the serial bus to be taken per bit time" "1,3" group.byte 0x28++0x00 line.byte 0x00 "COCNTRL,MCAN Output Control Register" bitfld.byte 0x00 7. " OCTP1 ,P-type output control transistors enable" "Disabled,Enabled" bitfld.byte 0x00 6. " OCTN1 ,N-type output control transistor enable" "Disabled,Enabled" bitfld.byte 0x00 5. " OCPOL1 ,Driver output polarity" "Low,High" bitfld.byte 0x00 4. " OCTP0 ,P-type output control transistors enable" "Disabled,Enabled" bitfld.byte 0x00 3. " OCTN0 ,N-type output control transistor enable" "Disabled,Enabled" bitfld.byte 0x00 2. " OCPOL0 ,Driver output polarity" "Low,High" bitfld.byte 0x00 0.--1. " OCM ,Output control mode bits" "Biphase,,Mode 1,Mode 2" else hgroup.byte 0x24++0x04 hide.byte 0x00 "CACC,MCAN Acceptance Code Register" hide.byte 0x01 "CACM,MCAN Acceptance Mask Register" hide.byte 0x02 "CBT0,MCAN Bus Timing Register 0" hide.byte 0x03 "CBT1,MCAN Bus Timing Register 1" hide.byte 0x04 "COCNTRL,MCAN Output Control Register" endif group.byte 0x2A++0x1 line.byte 0x00 "TBI,Transmit Buffer Identifier Register" line.byte 0x01 "TRTDL,Remote Transmission Request and Data Length Code Register" bitfld.byte 0x01 5.--7. " ID ,Identifier bits" "0,1,2,3,4,5,6,7" bitfld.byte 0x01 4. " RTR ,Remote transmission request" "Remote,Data" bitfld.byte 0x01 0.--3. " DLC ,Data length code bits" "0,1,2,3,4,5,6,7,8,..." group.byte 0x2C++0x00 line.byte 0x00 "TDS1,Transmit Data Segment 1" group.byte 0x2D++0x00 line.byte 0x00 "TDS2,Transmit Data Segment 2" group.byte 0x2E++0x00 line.byte 0x00 "TDS3,Transmit Data Segment 3" group.byte 0x2F++0x00 line.byte 0x00 "TDS4,Transmit Data Segment 4" group.byte 0x30++0x00 line.byte 0x00 "TDS5,Transmit Data Segment 5" group.byte 0x31++0x00 line.byte 0x00 "TDS6,Transmit Data Segment 6" group.byte 0x32++0x00 line.byte 0x00 "TDS7,Transmit Data Segment 7" group.byte 0x33++0x00 line.byte 0x00 "TDS8,Transmit Data Segment 8" group.byte 0x34++0x01 line.byte 0x00 "RBI,Receive Buffer Identity" line.byte 0x01 "RRTDL,RemoteTtransmission Request and Data Length Code Register" bitfld.byte 0x01 5.--7. " ID ,Identifier bits" "0,1,2,3,4,5,6,7" bitfld.byte 0x01 4. " RTR ,Remote transmission request" "Remote,Data" bitfld.byte 0x01 0.--3. " DLC ,Data length code bits" "0,1,2,3,4,5,6,7,8,..." group.byte 0x36++0x00 line.byte 0x00 "TDS1,Transmit Data Segment 1" group.byte 0x37++0x00 line.byte 0x00 "TDS2,Transmit Data Segment 2" group.byte 0x38++0x00 line.byte 0x00 "TDS3,Transmit Data Segment 3" group.byte 0x39++0x00 line.byte 0x00 "TDS4,Transmit Data Segment 4" group.byte 0x3A++0x00 line.byte 0x00 "TDS5,Transmit Data Segment 5" group.byte 0x3B++0x00 line.byte 0x00 "TDS6,Transmit Data Segment 6" group.byte 0x3C++0x00 line.byte 0x00 "TDS7,Transmit Data Segment 7" group.byte 0x3D++0x00 line.byte 0x00 "TDS8,Transmit Data Segment 8" width 0xb tree.end tree.end endif textline ""